Page 1
Operation Manual Wireless Adapter
PN-ZW01
Applicable models
(as of April 2018)
Available models differ according to region.
CAN ICES-3 (A) / NMB-3 (A)
Thank you for purchasing a SHARP product.
•
Before using the product, please be sure to read this operation manual carefully. Before using the product, be sure to read and understand the “SAFET Y
PRECAUTIONS” in the operation manual of the LCD MONITOR. After reading the manual, keep it in a convenient location where it can be accessed
at any time. As for how to use the product, refer to the manual of the LCD MONITOR.
LCD MONITOR
PN- B401/PN -B501/PN- M401/PN-M501
TIPS
- This product was shipped after strict quality control and inspection; however, if breakage or a malfunction should be found, contact your SHARP dealer
or your nearest customer contact.
- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other
malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.
- This product and its accessories may be upgraded without advance notice.
IMPORTANT:
To aid reporting in case of loss or theft, please record the product’s model
and serial numbers in the space provided. The numbers are located in the
rear of the product.
Model No.:
Serial No.:
U.S.A. ONLY
WARNING:
FCC Regulations state that any unauthorized changes or modications to this equipment not expressly approved by the manufacturer could void the
user’s authority to operate this equipment.
NOTE:
This equipment has been tested and found to comply with the limits for Class A digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may
cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.
FCC CAUTION
Changes or modications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This transmitter must not be co-located or operated in conjunction with any other antenna or transmitter.
U.S.A. ONLY
This device complies with Part 15 of FCC Rules and Industry Canada licence-exempt RSS standard(s). Operation is subject to the following two
conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause
undesired operation of this device.
This equipment complies with FCC/IC radiation exposure limits set forth for an uncontrolled environment and meets the FCC radio frequency (RF)
Exposure Guidelines and RSS-102 of the IC radio frequency (RF) Exposure rules. This equipment has very low levels of RF energy that are deemed
to comply without testing of specic absorption ratio (SAR).
U.S.A. AND
CANADA ONLY
WARNING:
This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take
adequate counter measures.
Page 2
To ensure safe and correct use
Updating the Firmware
This operation manual and the product use various displays and labels to
ensure safe use. Ignoring these displays and labels and incorrectly using
the product could have results as classied below.
Please read the following warning symbol information before reading the
rest of this section, and be sure to strictly observe all instructions.
Warning: Not following these instructions could result in
death or serious injury.
•Never try to modify, disassemble, or repair this product.
Doing so may result in re, electric shock, or injury.
•Onlyusetheaccessorieswithspeciedmodels.
Failure to do so may result in re.
Specications
Model
Wireless
communication method
Input/output terminals USB port (2.0 compliant) (Type A)
Dimensions
inch (mm)
Weight lbs. (g) Approx. 0.022 (10)
As a part of our policy of continuous improvement, SHARP reserves the
right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are
nominal values of production units. There may be some deviations from
these values in individual units.
PN-ZW01
2.4 GHz, IEEE802.11b/g/n
5 GHz, IEEE802.11a/n
Approx. 1 (W) x 3 (D) x 7/16 (H)
(26.1 x 76.9 x 10.7)
Supplied Components
If any components are missing, please contact your dealer.
□
Wireless adapter: 1
□
Operation manual (this manual)
Installing the Device
In order to use this product, the LCD monitor’s rmware must be updated.
Follow the steps below to update the rmware.
Introduction
n
On your computer, install the Information Display Downloader from the
CD-ROM that is included with the LCD monitor.
* For information on using the Information Display Downloader, see the
operation manual for the Information Display Downloader.
A USB ash drive is required. Ready a USB ash drive that meets the
following requirements.
File System FAT32
Capacity
Do not use a USB ash drive with a security function or write protection
function.
Firmware update procedure
n
1. Insert the USB ash drive into your computer.
2. Start the Information Display Downloader, and download the rmware
to use PN-ZW01 for your model.
3. Update the rmware by following the Update Manual in the
downloaded le.
Up to 32 GB
(maximum le size 4 GB)
Wireless LAN Settings
When you have nished updating the rmware, follow the steps below to
congure the wireless LAN settings on the LCD monitor.
* For information on using the LCD monitor, see the operation manual
for the LCD monitor and the Software Guide.
1. Change the input mode to “APPLICATION” with the input mode
selection, or press the CONTENT MENU button.
2. Select “Setup” in the base screen of APPLICATION mode.
3. Set the “Network priority”.
If you will use wireless on the LCD monitor, we recommend that you
select “Wi-Fi > Ethernet”.
4. Select “Wi-Fi (Wireless LAN)” and display the AndroidTM screen.
5. Enable Wi-Fi in the Android settings, and congure the wireless LAN
settings.
Trademarks
n
• Android is a trademark of Google LLC.
• Wi-Fi is a registered trademark of Wi-Fi Alliance.
1. Insert the device into a USB port on the LCD monitor.
Loading...