Sharp PN-ZS1C User Manual

1670 (65 3/4)

634

(24

/16)

815*

(32

/16)

Installation procedure

* * *

(continued)

Attach the left and right back cover with 16 supplied

M6 screws.

Cables can be bundled by

Back cover

Attach the cover reinforcement angle with the

supplied M6 screws to secure the front cover. (Use

10 screws for 1600 mm (63 inch), 7 screws for

1500 mm (59 1/16 inch).)

attaching the cable clamp to the back cover.

Main specications

Model PN-ZS1C Dimensions See the gure below.

Weight

As a part of our policy of continuous improvement, SHARP reserves

the right to make design and specication changes for product improvement without prior notice. The performance specication gures indicated are nominal values of production units. There may

be some deviations from these values in individual units.

Approx. 77 kg (169.8 lbs.) (Weight includes support rods, covers and screws)

Unit: mm (inch)

(The gure shows the approximate values.)

Operation Manual

PN-ZS1C

Stand cover

Applicable models (as of July 2008)

Thank you for purchasing a SHARP product.

•

Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be accessed at any time.

TIPS

Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party,

nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law. This product and its accessories may be upgraded without advance notice.

LCD MONITOR LB-1085

To ensure safe and correct use

* Not used when 1500 mm (59 1/16 inch)

* Height when mounted at 1600 mm (63 inch)

715 mm (28 1/8 inch) when mounted at 1500 mm (59 1/16 inch)

This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels

and incorrectly using the product could have results as classied below.

Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all instructions.

Warning:

The installation must be performed by qualied service personnel.

•

Improper installation work may cause the monitor to fall or topple over, resulting in injury.

Secure the stand with the anchor bolts before assembling these parts.

•

Otherwise, the monitor may topple over, resulting in injury.

Only use the accessories with specied models. Do not modify the LCD Monitor or the accessories.

•

Otherwise, the monitor may fall or topple over, resulting in injury.

Caution:

Tighten all the screws and bolts fully and securely.

•

Insufcient tightening may cause the monitor to fall or topple over, resulting in injury.

When any deformation or cracks are found please stop using the LCD Monitor.

•

Using the monitor without repairing the problem may cause the monitor to fall or topple over, resulting in injury.

Not following these instructions could result in death or serious injury.

Not following these instructions could result in injury or property damage.

Printed in Japan

EN(1)

- -

Supplied accessories

1600 mm* (63 inch)

1500 mm* (59 1/16 inch)

Conrm that the following accessories have been provided with the product.

□

Support rod x 2

□

M8 bolt x 4

□

M8 spring washer x 4

□

M8 plain washer x 4

□

Left and right base reinforcement

angles (x 1 each)

□

Left and right cover mounting

angles (x 1 each)

□

Front and rear base plates (x 1 each)

□

Front cover x 1

□

Extension front cover x 1

□

Left and right back covers (x 1 each)

□

Cover reinforcement angle x 1

□

M6 screw x 56

□

Cable clamp x 4

□

Operation manual (this manual)

Precautions on use

The installation, removal, or transportation of the LCD Monitor must be performed by qualied service personnel.

•

The LCD Monitor is large and heavy. Installation requires special knowledge and qualications. Customers should not attempt to install, remove, or transport the LCD Monitor by themselves.

•

SHARP shall have no liability for any accidents or damages caused by improper installation or mishandling.

•

Mount the support rods to the stand.

Mount using the supplied M8 bolts.

• The support rods can be mounted at two different

• heights.

Spring washer

Plain washer

*Height to center of the LCD Monitor

Hoist to the height where the LCD Monitor is to be

mounted.

Mounting stand cover

Attach the base reinforcement angle (L and R) to the

stand of the monitor with 6 supplied M6 screws.

Base reinforcement angle

Mount the LCD Monitor to the stand (and support

rods) using the bolts removed in step 3.

Plain washer

Spring washer

Conrm that the LCD Monitor is mounted securely,

and then remove the hooks of the hoisting device.

[Step 4 continued]

When height is 1600 mm (63 inch)

•

(1) Attach the extension front cover with 4 supplied M6

screws.

Extension front cover

Installation procedure

Mounting support rods

Caution

The LCD Monitor is large and heavy. It must be moved with a hoisting device (chain block, etc.).

• Installation requires at least four people.

•

Make sure the LCD Monitor stand is secured with

anchor bolts.

Insert the hooks of the hoisting device into the eye

bolts of the LCD Monitor and slightly lift the monitor.

Lift up the monitor so that the hoisting chains become

• taut.

Remove the stand mounting bolts on the rear and

detach the LCD Monitor from the stand.

Loosen the 8 bolts gradually and evenly.

•

If it is difcult to loosen the bolts, lift the monitor up

slightly with the hoisting device to reduce the load on the bolts. Check the hoisting condition frequently to prevent the

• LCD Monitor from falling.

- -

Attach the front base plate with 3 supplied M6

screws.

Front base plate

Attach the rear base plate, then the cover mounting

angle (L and R) with 9 supplied M6 screws.

Rear base plate

Attach the front cover with the top edge up.

Turn the front cover over if the screw holes are not

• aligned. Make sure that the front cover does not scrape against

• the base plates to prevent scratching.

Front cover mounting procedure

Fit one side of the front cover over the cover mounting angle

(1), then t the other side while pulling outwards (2, 3, 4).

Cover mounting angle

(2) Attach the front cover with 8 supplied M6 screws.

Front cover

When height is 1500 mm (59 1/16 inch)

•

(1) Attach the front cover with 10 supplied M6 screws.

Front cover

*Rear side of front cover