Sharp PN-ZK10 User Manual
97 (3 13/16)116 (4 9/16)
1835 (72
1
/
4
)
Main specications
Model PN-ZK10
Dimensions See the gure below.
Weight Approx. 23 kg (50.7 lbs.) (Weight includes two mounting brackets and bolts)
As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement
without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from
these values in individual units.
Unit: mm (inch)
(The gure shows the approximate values.)
Operation Manual
PN-ZK10
Mounting Bracket
Applicable models (as of July 2008)
Thank you for purchasing a SHARP product.
•
Before using the product, please be sure to read this operation manual carefully. In particular, be sure to read the
section “To ensure safe and correct use”. After reading the manual, keep it in a convenient location where it can be
accessed at any time.
TIPS
Please understand that Sharp Corporation bears no responsibility for errors made during use by the customer or a third party,
nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized
under law.
This product and its accessories may be upgraded without advance notice.
-
LCD MONITOR LB-1085
To ensure safe and correct use
This operation manual and the product use various displays and labels to ensure safe use. Ignoring these displays and labels
and incorrectly using the product could have results as classied below.
Please read the following warning symbol information before reading the rest of this section, and be sure to strictly observe all
instructions.
Warning:
The installation must be performed by qualied service personnel.
•
Improper installation work may cause the monitor to fall or topple over, resulting in injury.
Only use the accessories with specied models. Do not modify the LCD Monitor or the accessories.
•
Otherwise, the monitor may fall or topple over, resulting in injury.
Install the LCD Monitor in a location with minimal vibration and that is strong enough to hold the weight of
•
the LCD Monitor and mounting brackets.
Otherwise, the monitor may fall or topple over, resulting in injury.
Do not apply a load other than the LCD Monitor to the mounting brackets.
•
Otherwise, the monitor may fall or topple over, resulting in injury.
Caution:
Tighten all the screws and bolts fully and securely.
•
Insufcient tightening may cause the monitor to fall or topple over, resulting in injury.
When any deformation or cracks are found please stop using the LCD Monitor.
•
Using the monitor without repairing the problem may cause the monitor to fall or topple over, resulting in injury.
Not following these instructions could result in death or serious injury.
Not following these instructions could result in injury or property damage.
Printed in Japan
EN(1)
-
4
- -
1
-
M16 spring washe
r
M16 plain washer
Countersunk bolt
plain washer
Countersunk bolt
M8 spring washer
M8 plain washer
Supplied accessories
Conrm that the following accessories have been provided with the product.
□
Mounting bracket x 2
□
M8 bolt x 4
□
M10 bolt x 4
□
M16 bolt x 8
□
Countersunk bolt (M10) x 2
□
M8 spring washer x 4
□
M8 plain washer x 4
□
M16 spring washer x 4
□
M16 plain washer x 4
□
M10 (countersunk bolt) plain washer x 2
□
Operation manual (this manual)
Precautions on use
The installation, removal, or transportation of the LCD Monitor must be performed by qualied service personnel.
•
The LCD Monitor is large and heavy. Installation requires special knowledge and qualications.
Customers should not attempt to install, remove, or transport the LCD Monitor by themselves.
•
SHARP shall have no liability for any accidents or damages caused by improper installation or mishandling.
•
The installation requires two H-shaped steel frames set upright with bored mounting screw holes. For details, contact your
•
product dealer.
Attach the mounting brackets on the rear of the LCD
4
Monitor.
1) Attach 4 supplied M16 bolts, 2 on the right and 2
on the left as shown below, and slightly tighten the
bolts.
2) Attach the mounting brackets by inserting the bolts
through the 2 holes in the center.
Attach the LCD Monitor (mounting brackets) to the
6
H-shaped steel frame.
1) Hook the bottoms of the mounting brackets to the
bolts attached in step 5.
2) Conrm that the mounting brackets are securely
hooked and then attach the 2 supplied countersunk
bolts.
3) Tighten the countersunk bolts while gradually
loosening the chains of the hoisting device.
Installation procedure
Caution
The LCD Monitor is large and heavy. It must be moved with a hoisting device (chain block, etc.).
•
Installation requires at least four people.
•
Move the LCD Monitor in front of the H-shaped steel
1
frame to which it will be attached.
Insert the hooks of the hoisting device into the eye
2
bolts of the LCD Monitor and slightly lift the monitor.
Lift up the monitor so that the hoisting chains become
•
taut.
Remove the stand mounting bolts on the rear and
3
detach the LCD Monitor from the stand.
Loosen the 8 bolts gradually and evenly.
•
If it is difcult to loosen the bolts, lift the monitor up
slightly with the hoisting device to reduce the load on
the bolts.
Check the hoisting condition frequently to prevent the
•
LCD Monitor from falling.
3) Secure the mounting brackets with 4 supplied M16
bolts inserted into the remaining 2 holes on each
side.
4) Fully tighten the bolts which were tightened halfway
in step 1).
Attach the supplied M10 bolts to the H-shaped steel
5
frame so that you can hook the LCD Monitor
(mounting brackets).
1) Attach the bolts onto the both sides of the right and
left frames and ensure that all 4 of the bolts are
aligned at the same height.
4) Insert the 4 supplied M8 bolts from the sides of the
mounting brackets (2 for each) and secure them.
Conrm that the LCD Monitor is mounted securely,
7
and then remove the hooks of the hoisting device.
-
2
- -
3
-
Loading...