Sharp PN-80TC3 User Guide

Download

Page 1

PN-80TC3

LCD MONITOR

OPERATION MANUAL

Page 2

Information on the Disposal of this Equipment and its Batteries

IF YOU WISH TO DISPOSE OF THIS EQUIPMENT OR ITS BATTERIES, DO NOT USE THE ORDINARY WASTE BIN, AND DO NOT PUT THEM INTO A FIREPLACE! Used electrical and electronic equipment and batteries should always be collected and treated SEPARATELY in accordance with local law.

Separate collection promotes an environment-friendly treatment, recycling of materials, and minimizing nal disposal of

waste. IMPROPER DISPOSAL can be harmful to human health and the environment due to certain substances! Take USED EQUIPMENT to a local, usually municipal, collection facility, where available. Remove USED BATTERIES from equipment, and take them to a battery collection facility; usually a place where new batteries are sold. If in doubt about disposal, contact your local authorities or dealer and ask for the correct method of disposal. ONLY FOR USERS IN THE EUROPEAN UNION, AND SOME OTHER COUNTRIES; FOR INSTANCE NORWAY AND SWITZERLAND: Your participation in separate collection is requested by law. The symbol shown above appears on electrical and electronic equipment and batteries (or the packaging) to remind users of this. If ‘Hg’ or ‘Pb’ appears below the symbol, this means that the battery contains traces of mercury (Hg) or lead (Pb), respectively. Users from PRIVATE HOUSEHOLDS are requested to use existing return facilities for used equipment and batteries. Batteries are collected at points of sale. Return is free of charge. If the equipment has been used for BUSINESS PURPOSES, please contact your SHARP dealer who will inform you about take-back. You might be charged for the costs arising from take-back. Small equipment (and small quantities) might be taken back by your local collection facility. For Spain: Please contact the established collection system or your local authority for take-back of your used products.

Page 3

IMPORTANT INFORMATION

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT

TO RAIN OR MOISTURE.

The lightning ash with arrowhead symbol, within

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC

SHOCK, DO NOT REMOVE COVER. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

a triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of

sufcient magnitude to constitute a risk of electric

shock to persons.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FOR CUSTOMERS IN U.K.

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

GREEN-AND-YELLOW: Earth BLUE: Neutral BROWN: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

• The wire which is coloured GREEN-AND-YELLOW must be connected to the terminal in the plug which is marked by the

letter E or by the safety earth

• The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.

• The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.

Ensure that your equipment is connected correctly. If you are in any doubt consult a qualied electrician.

“WARNING: THIS APPARATUS MUST BE EARTHED.”

or coloured green or green-and-yellow.

Page 4

DEAR SHARP CUSTOMER

Thank you for your purchase of a SHARP LCD product. To ensure safety and many years of trouble-free operation of your product, please read the Safety Precautions carefully before using this product.

SAFETY PRECAUTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can

result in electric shock and/or re. In order to prevent potential danger, please observe the following instructions when installing,

operating and cleaning the product. To ensure your safety and prolong the service life of your LCD product, please read the following precautions carefully before using the product.

1. Read instructions — All operating instructions must be read and understood before the product is operated.

2. Keep this manual in a safe place — These safety and operating instructions must be kept in a safe place for future reference.

3. Observe warnings — All warnings on the product and in the instructions must be observed closely.

4. Follow instructions — All operating instructions must be followed.

5. Cleaning — Unplug the power cord from the AC outlet before cleaning the product. Use a dry cloth to clean the product. Do not use liquid cleaners or aerosol cleaners. Do not use dirty cloths. Doing so may damage the product.

6. Attachments — Do not use attachments not recommended by the manufacturer. Use of inadequate attachments can result in accidents.

7. Water and moisture — Do not use the product near water. Do not install the product in a place where water may splash onto it. Be careful of equipment which drains water such as an air-conditioner.

8. Ventilation — The vents and other openings in the cabinet are designed for ventilation.

Do not cover or block these vents and openings since insufcient ventilation can cause overheating and/or shorten the life

of the product. Do not place the product on a sofa, rug or other similar surface, since they can block ventilation openings. Do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

9. Power cord protection — The power cords must be routed properly to prevent people from stepping on them or objects from resting on them.

10. The screen used in this product is made of glass. Therefore, it can break when the product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the screen breaks.

11. Overloading — Do not overload AC outlets or extension cords. Overloading can cause re or electric shock.

12. Entering of objects and liquids — Never insert an object into the product through vents or openings. High voltage ows in

the product, and inserting an object can cause electric shock and/or short internal parts.

For the same reason, do not spill water or liquid on the product.

13. Servicing — Do not attempt to service the product yourself. Removing covers can expose you to high voltage and other

dangerous conditions. Request a qualied service person to perform servicing.

14. Repair — If any of the following conditions occurs, unplug the power cord from the AC outlet, and request a qualied service

person to perform repairs. a. When the power cord or plug is damaged. b. When a liquid was spilled on the product or when objects have fallen into the product. c. When the product has been exposed to rain or water. d. When the product does not operate properly as described in the operating instructions. Do not touch the controls other than those described in the operating instructions. Improper adjustment of controls

not described in the instructions can cause damage, which often requires extensive adjustment work by a qualied

technician. e. When the product has been dropped or damaged. f. When the product displays an abnormal condition. Any noticeable abnormality in the product indicates that the product

needs servicing.

15. Replacement parts — In case the product needs replacement parts, make sure that the service person uses replacement

parts specied by the manufacturer, or those with the same characteristics and performance as the original parts. Use of unauthorized parts can result in re, electric shock and/or other danger.

16. Safety checks — Upon completion of service or repair work, request the service technician to perform safety checks to

ensure that the product is in proper operating condition.

17. Wall mounting — When mounting the product on a wall, be sure to install the product according to the method

recommended by the manufacturer.

18. Heat sources — Keep the product away from heat sources such as radiators, heaters, stoves and other heat-generating

products (including ampliers).

Page 5

SAFETY PRECAUTIONS (Continued)

19. Batteries — Incorrect use of batteries may cause the batteries to burst or ignite. A leaky battery may corrode the equipment,

dirty your hands or spoil your clothing. In order to avoid these problems, make sure to observe the precautions below:

• Use the specied batteries only.

• Install the batteries with due attention to the plus (+) and minus (-) sides of the batteries according to the instructions in the

compartment.

• Do not mix old and new batteries.

• Do not mix batteries of different types. Voltage specications of batteries of the same shape may vary.

• Replace an exhausted battery with a new one promptly.

• If you will not use the remote control for a long time, remove the batteries.

• If leaked battery uid gets on your skin or clothing, rinse immediately and thoroughly. If it gets into your eye, bathe your

eye well rather than rubbing and seek medical treatment immediately. Leaked battery uid that gets into your eye or your

clothing may cause a skin irritation or damage your eye.

20. Usage of the monitor must not be accompanied by fatal risks or dangers that, could lead directly to death, personal injury,

severe physical damage or other loss, including nuclear reaction control in nuclear facility, medical life support system, and missile launch control in a weapon system.

21. Do not stay in contact with the parts of the product that become hot for long periods of time. Doing so may result in

low-temperature burns.

22. Do not modify this product.

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

To maintain compliance with EMC regulations, use shielded cables to connect to the following terminals: HDMI input terminal, D-SUB input terminal, DisplayPort input/output terminals and RS-232C input terminal.

If a monitor is not positioned in a sufciently stable location, it can be potentially hazardous due to falling. Many injuries,

particularly to children, can be avoided by taking simple precautions such as:

• Using xing devices like wall mount brackets recommended by the manufacturer.

• Only using furniture that can safely support the monitor.

• Ensuring the monitor is not overhanging the edge of the supporting furniture.

• Not placing the monitor on tall furniture (for example, cupboards or bookcases) without anchoring both the furniture and the

monitor to a suitable support.

• Not standing the monitors on cloth or other materials placed between the monitor and supporting furniture.

• Educating children about the dangers of climbing on furniture to reach the monitor or its controls.

Especially for child safety

- Don’t allow children to climb on or play with the monitor.

- Don’t place the monitor on furniture that can easily be used as steps, such as a chest of drawers.

- Remember that children can become excited while watching a program, especially on a “larger than life” monitor. Care should be taken to place or install the monitor where it cannot be pushed, pulled over, or knocked down.

- Care should be taken to route all cords and cables connected to the monitor so that they cannot be pulled or grabbed by curious children.

Page 6

TIPS AND SAFETY INSTRUCTIONS

The TFT color LCD panel used in this monitor is made with the application of high precision technology. However, there may be minute points on the screen where pixels never light or are permanently lit. Also, if the screen is viewed from an acute angle there may be uneven colors or brightness. Please note that these are not malfunctions but common phenomena of LCDs and will not affect the performance of the monitor.

- Do not display a still picture for a long period, as this could cause a residual image.

- Never rub or tap the monitor with hard objects.

- Please understand that SHARP CORPORATION bears no responsibility for errors made during use by the customer or a third party, nor for any other malfunctions or damage to this product arising during use, except where indemnity liability is recognized under law.

- This monitor and its accessories may be upgraded without advance notice.

Do not use the monitor where there is a lot of dust, where humidity is high, or where the monitor may come into contact with oil or steam. Do not use in an environment where there are corrosive

gases (sulfur dioxide, hydrogen sulde, nitrogen dioxide, chlorine, ammonia, ozone, etc.). As this could lead to re.

Ensure that the monitor does not come into contact with water

or other uids. Ensure that no objects such as paper clips or pins enter the monitor as this could lead to re or electric shock.

- Do not place the monitor on top of unstable objects or in unsafe places. Do not allow the monitor to receive strong shocks or to strongly vibrate. Causing the monitor to fall or topple over may damage it.

- Do not use the monitor near heating equipment or in places where there is likelihood of high temperature, as this may

lead to generation of excessive heat and outbreak of re.

- Do not use the monitor in places where it may be exposed to direct sunlight. Risk of cabinet deformation and failure if the monitor is used in direct sunlight.

- Images cannot be rotated on this monitor. When using in portrait orientation, you will need to prepare appropriately orientated content in advance.

- The AC outlet shall be installed near the equipment and shall be easily accessible.

- Please be sure to constantly remove dust and garbage that has attached to the ventilation opening. If dust collects in the ventilation opening or the inside of the monitor, it may lead to excessive heat, outbreak of re, or malfunction. Please request a cleaning of the inside of the monitor from an authorized SHARP servicing dealer or service center.

- Do not touch the screen when the monitor power is turned on, it will lead to a malfunction. When this occurs, turn the monitor power off and then on.

- Do not operate the screen with a hard or pointed object such

as a ngernail or pencil.

- Depending on the application used, the touch pen may not function.

- If another USB device is connected to the computer to which the touch panel is connected, do not operate the USB device during touch panel input. Input may not take place correctly.

- Do not allow a cable to come near the screen. This may cause the touch panel to malfunction.

The Power Cord

- Use only the power cord supplied with the monitor.

- Do not damage the power cord nor place heavy objects on it, stretch it or over bend it. Also, do not add extension cords.

Damage to the cord may result in re or electric shock.

- Do not use the power cord with a power tap.

Adding an extension cord may lead to re as a result of

overheating.

- Do not remove or insert the power plug with wet hands. Doing so could result in electric shock.

- Unplug the power cord if it is not used for a long time.

- Do not attempt to repair the power cord if it is broken or malfunctioning. Refer the servicing to the service representative.

Manual Scope

- Microsoft, Windows, Internet Explorer, Excel and PowerPoint are either registered trademarks or trademarks of Microsoft Corporation in the United States and/or other countries.

- The terms HDMI and HDMI High-Denition Multimedia

Interface, and the HDMI Logo are trademarks or registered trademarks of HDMI Licensing, LLC in the United States and other countries.

- DisplayPort is a registered trademark of Video Electronics Standards Association.

- Adobe, Acrobat, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/or other countries.

- Intel, Celeron, and Intel Core 2 Duo are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the U.S.A. and other countries.

- AMD, AMD Sempron, AMD Athlon, and combinations thereof are trademarks of Advanced Micro Devices, Inc.

- This product comes with RICOH Bitmap Fonts produced and sold by RICOH COMPANY, LTD.

- All other brand and product names are trademarks or registered trademarks of their respective holders.

- Language of OSD menu used in this manual is English by way of example.

- Illustrations in this manual may not exactly represent the actual product or display.

- This manual assumes use in landscape orientation, except

where specically noted.

LED Backlight

● The LED backlight in this product has a limited lifetime.

* If the screen gets dark or does not turn on, it may be

necessary to replace the LED backlight.

* This LED backlight is exclusive to this product and must

be replaced by an authorized SHARP servicing dealer or service center. Please contact an authorized SHARP servicing dealer or service center for assistance.

Page 7

MOUNTING PRECAUTIONS

Cable clamp

• This product is for use indoors.

• A mounting bracket compliant with VESA specications is

required.

• Since the monitor is heavy, consult your dealer before

installing, removing or moving the monitor.

• Mounting the monitor on the wall requires special expertise

and the work must be performed by an authorized SHARP dealer. You should never attempt to perform any of this work yourself. Our company will bear no responsibility for accidents or injuries caused by improper mounting or mishandling.

• Use the monitor with the surface perpendicular to a level

surface. If necessary, the monitor may be tilted up to 20 degrees upward.

• When moving the monitor, be sure to hold it with the

handles and the unit bottom. Do not grasp the screen, tray, speaker, or speaker cover. This may cause product damage, failure, or injury.

• This monitor should be used at an ambient temperature

between 41°F (5°C) and 95°F (35°C).

• Be careful of high temperatures in the surrounding area.

When installing the monitor inside a housing, or if the ambient temperature may be outside of the range of 41°F (5°C) to 95°F (35°C), install a fan or take other measures to keep the ambient temperature within the required range.

• Temperature condition may change when using the monitor

together with the optional equipments recommended by SHARP. In such cases, please check the temperature

condition specied by the optional equipments.

• Do not block any ventilation openings. If the temperature

inside the monitor rises, this could lead to a malfunction.

• Do not place the monitor on a device which generates heat.

• Adhere to the following when installing the monitor in its

portrait orientation. Failing to adhere to the following may cause malfunctions.

- Install the monitor such that the power LED is located on the bottom side.

Power LED

- Set the MONITOR on the MONITOR menu to PORTRAIT. (See page 33.)

- Be sure to clamp the power cord (supplied) onto the cable clamp attachment using the supplied cable clamp. When clamping the power cord, take care not to stress the terminal of the power cord. Do not bend the power cord excessively.

Power cord (Supplied)

• Use the supplied vertical sticker when you install the

monitor in portrait orientation.

Cable clamp attachment

Cover SHARP logo

Logo

Page 8

Contents

IMPORTANT INFORMATION ............................................3

DEAR SHARP CUSTOMER ..............................................4

SAFETY PRECAUTIONS ..................................................4

TIPS AND SAFETY INSTRUCTIONS ...............................6

MOUNTING PRECAUTIONS ............................................7

Supplied Components .....................................................9

System Requirements .....................................................9

Part Names .....................................................................10

Connecting Peripheral Equipment ...............................12

Connecting the Power Cord .........................................14

Binding Cables ...............................................................14

Preparing the Remote Control Unit ..............................15

Installing the batteries ................................................15

Remote control operation range .................................15

Removing the Handles ..................................................16

Mounting a web camera ................................................16

Turning Power On/Off ....................................................17

Turning on the main power.........................................17

Turning power on .......................................................17

Turning power off .......................................................17

Touch Panel / Touch Pen Preparations ........................19

Connecting the touch pen adapter .............................19

Touch Pen Preparations ............................................. 19

Computer preparations ..............................................19

Calibration ..................................................................19

Touch pen actions ......................................................20

Adding touch pens (pairing) .......................................20

Touch action ...................................................................21

Touch action ............................................................... 21

Other functions ...........................................................23

Cautionary points .......................................................23

Eraser .........................................................................23

Basic Operation .............................................................24

Using the touch menu ................................................24

Using the remote control unit .....................................25

Menu Items .....................................................................27

Displaying the menu screen .......................................27

Menu item details .......................................................28

Adjustments for PC screen display ............................38

Initialization (Reset)/Functional Restriction Setting

(FUNCTION) ....................................................................39

Controlling the Monitor with a PC (RS-232C) ..............40

PC connection ............................................................40

Communication conditions .........................................40

Communication procedure .........................................40

Setting of the GAMMA user data ................................42

RS-232C command table ...........................................43

Controlling the Monitor with a PC (LAN) .....................51

Settings to connect to a LAN ......................................51

Controlling with a PC ..................................................53

[Advanced operation]

Command-based control ............................................59

Troubleshooting .............................................................60

Specications ...............................................................62

Mounting Precautions

(For SHARP dealers and service engineers) ...............67

For information on Touch Pen Utility, Touch Panel Settings Tool, Pen Software, Touch Display Downloader and Touch Display Link, see the manual for each.

Page 9

Supplied Components

If any components are missing, please contact your dealer.

Liquid Crystal Display Monitor: 1



Remote control unit: 1



Power cord



Remote control unit battery



(R-6 (“AA” size)): 2

Cable clamp: 3



Cable clamp (insertion type): 4



CD-ROM (Utility Disk): 1



CD-ROM (Touch Display Link): 1



Touch Display Link License: 1



Setup Manual: 1



Touch pen (for capacitive touch panel)



(PN-ZL03): 2

Touch pen adapter (PN-ZL01): 1



Pen tip for touch pen



(for capacitive touch panel): 8

Touch pen battery



(LR-03 (“AAA” size)): 2

Tray: 1



Speaker cover: 2



USB cable: 1



RS-232C conversion cable (3.5mm mini jack): 1



Eraser (for capacitive touch panel): 1



Camera mount: 1



Camera screw (inch thread): 1



Touch pen adapter screw (Step screw, M3): 1



Speaker cover attachment screws (M3)/



Camera mount screws (M3): 6

Vertical sticker (Logo): 1



ID labels (for touch pen): 4 x 2



Cover SHARP logo: 1



Place this sticker onto the SHARP logo to cover the logo.

* SHARP Corporation holds authorship rights to the Utility Disk program. Do not reproduce it without permission. * For environmental protection! Do not dispose of batteries in household waste. Follow the disposal instructions for your area.

System Requirements

Computer

PC/AT compatible computer with a USB 2.0 port and able to output a resolution of 1920 x 1080. (CD-ROM drive required for software installation.)

Windows 7 (32-bit or 64-bit version),

Windows 8 (32-bit or 64-bit version), Windows 8.1 (32-bit or 64-bit version), Windows 10 (32-bit or 64-bit version)

CPU

Intel Celeron or AMD Sempron 1.6 GHz or faster

Intel Core 2 Duo or AMD Athlon II X2 2.8 GHz or faster recommended Memory At least 2 GB Free space on hard drive At least 200 MB (free space separately required for data storage)

To use the touch panel, the touch panel and computer must be connected, and Touch Panel Settings Tool, Touch Pen Utility, and Pen Software must be installed on the computer from the supplied CD-ROM. When the Touch Display Downloader is installed, you can check and download the most recent versions of the software programs. To install the software, see the manual for each.

The USB port varies depending on the terminal connected to the computer.

D-sub 1 input terminal/DisplayPort input terminal/HDMI 1 input terminal USB 1 port D-sub 2 input terminal/HDMI 2 input terminal/HDMI 3 input terminal USB 2 port

(Factory setting. Can be changed in TOUCH INPUT SELECT in the SETUP menu.)

Download the setup program for the Touch Viewing Software with the Touch Display Downloader.

Page 10

Front view

9 10

Part Names

12 3

1. Remote control sensor (See page 15.)

2. Power LED (See page 17.)

3. Power button (See page 17.)

4. TOUCH MENU button (See page 24.)

Rear view

TIPS

• It is convenient to use the terminals for separate purposes;

for example, using the terminal on the bottom of the monitor

to connect a xed computer and using the terminal on the

side of the monitor to connect a mobile computer.

Caution

• Consult your SHARP dealer for attachment/detachment of

optional parts.

14 201915 16 181713

67 7

5. USB port (for USB device) (USB 2.0 compliant)

To use, remove the seal and connect the USB cable on the back of the tray (“31”) to the computer. (See page 13.)

6. Tray

7. Speakers

8. Handles

9. Vents

10. Optional attachment section

This section is used to connect optional

hardware for function expansion. Offering this attachment location is not a guarantee that future compatible hardware attachments will be released.

11. Main power switch (See page 17.)

12. AC input terminal (See page 14.)

13. External speaker terminals (See page 13.)

14. Audio output terminal (See page 13.)

15. DisplayPort output terminal (See page 13.)

16. Touch pen adapter port (See page 19.)

17. USB 1 port (for touch panel) (See page 13.)

18. LAN terminal (See page 13.)

19. Optional terminal

This terminal is provided for possible future (optional) function expansion. Offering of this terminal is not a guarantee that future expanded functionality will be provided.

20. D-sub 1 input terminal (See page 12.)

21. DisplayPort input terminal (See page 12.)

22. HDMI 1 input terminal (See page 12.)

23. Audio 1 input terminal (See page 13.)

24. RS-232C input terminal (See page 13.)

25. Terminal for rmware updating Normally not used.

26. USB 2 port (for touch panel) (See page 13.)

27. D-sub 2 input terminal (See page 12.)

28. HDMI 2 input terminal (See page 12.)

29. HDMI 3 input terminal (See page 12.)

30. Audio 2 input terminal (See page 13.)

31. USB cable (See page 13.)

Page 11

Remote control unit

Part Names

1. Signal transmitter

2. POWER button (See page 17.)

3. MUTE button (See page 25.)

4. VOL +/- buttons (See page 25.) BRIGHT +/- buttons (See page 25.)

Cursor control (

5. DISPLAY button (See page 25.)

6. MODE button (See page 25.)

7. INPUT button (See page 25.)

8. MENU button (See page 25.)

9. ENTER button (See page 25.)

10. RETURN button (See page 25.)

11. SIZE button (See page 25.)

/ / / ) buttons

Page 12

Connecting Peripheral Equipment

Caution

• Be sure to turn off the main power switch and disconnect

the plug from the power outlet before connecting/ disconnecting cables. Also, read the manual of the equipment to be connected.

• Be careful not to confuse the input terminal with the output

terminal when connecting cables. Accidentally reversing cables connected to the input and output terminals may cause malfunctions and the other problems.

• Do not use any cable that has a damaged or deformed

terminal. Using such cables may cause malfunctions.

TIPS

•

When using a touch panel, connect the USB cable to the computer. For details, see the Touch Panel Settings Tool Operation Manual.

• Images may not be displayed properly depending on the

computer (video card) to be connected.

• Use the automatic screen adjustment when a computer screen is displayed for the rst time using D-SUB1 or

D-SUB2, or when the setting of the computer is changed. The screen is adjusted automatically when SELF ADJUST in the MONITOR menu is set to ON.

• If the audio output from the playback device is connected

directly to speakers or other devices, the video on the monitor may appear delayed from the audio portion. Audio should be played through this monitor by connecting the playback device to the monitor’s audio input, and connecting the monitor’s audio output to the speakers or other devices.

• The audio input terminals used in each input mode are

factory-set as follows.

Input mode

D-SUB1 Audio 1 input terminal D-SUB2 Audio 2 input terminal DisplayPort DisplayPort input terminal HDMI1 HDMI 1 input terminal HDMI2 HDMI 2 input terminal HDMI3 HDMI 3 input terminal

Audio input terminal (Factory setting)

710 5 149 11 151216

It is convenient to use the terminals for separate purposes; For example, using the terminal on the bottom of the monitor

to connect a xed computer and using the terminal on the side

of the monitor to connect a mobile computer.

1. HDMI 1 input terminal

2. HDMI 2 input terminal

3. HDMI 3 input terminal

• Use a commercially available HDMI cable (conforming to

the HDMI standard).

• Set HDMI1/HDMI2/HDMI3 of INPUT SELECT on the

SETUP menu according to the device to be connected.

• Select the audio input terminal to be used in AUDIO

SELECT of the SETUP menu. When HDMI is selected, connection to the audio input terminal is unnecessary.

4. DisplayPort input terminal

• Use a commercially available DisplayPort cable

(conforming to the DisplayPort standard).

• Select the audio input terminal to be used in AUDIO

SELECT of the SETUP menu. When DisplayPort is selected, connection to the audio input terminal is unnecessary.

5. D-sub 1 input terminal

• Set D-SUB1 of INPUT SELECT on the SETUP menu

according to the device to be connected.

• To use with D-SUB1[VIDEO], connect the green terminal

to the device’s video output.

• Select the audio input terminal to be used in AUDIO

SELECT of the SETUP menu.

6. D-sub 2 input terminal

• Select the audio input terminal to be used in AUDIO

SELECT of the SETUP menu.

Page 13

Connecting Peripheral Equipment

7. Audio 1 input terminal

8. Audio 2 input terminal

• Useanaudiocablewithoutresistance.

• Settheaudioinputterminaltobeusedineachinput modeinAUDIOSELECTontheSETUPmenu.

9. DisplayPort output terminal

• Thescreendisplayedonthemonitorandtheaudiooutput fromthemonitorcanbeoutputtoanexternaldevice.

• UseacommerciallyavailableDisplayPortcable (conformingtotheDisplayPortstandard).

• OutputtingHDCP-encryptedvideorequiresanexternal devicewhichsupportsHDCP.

10. Audio output terminal

• Theoutputsoundvariesdependingontheinputmode.

• Thevolumeoftheoutputsoundcanbexedbysetting AUDIOOUTPUTofAUDIOOPTIONontheSETUP menu.

• Itisnotpossibletocontrolthesoundoutputfromthe audiooutputterminalswiththeAUDIOmenu.

11. Touch pen adapter port

• Connectthetouchpenadapterinordertousethetouch pen.(Seepage19.)

12. USB 1 (type B) port

• Tousethetouchpanelwithacomputerconnectedtothe terminalbelow,connectthetouchpaneltothecomputer withaUSBcable. (Factorysetting.CanbechangedinTOUCHINPUT SELECTontheSETUPmenu.)

-D-sub1inputterminal

-DisplayPortinputterminal

-HDMI1inputterminal

13. USB 2 (type B) port

-D-sub2inputterminal

-HDMI2inputterminal

-HDMI3inputterminal

14. RS-232C input terminal

• Themonitorcanbeconnectedtoacomputerusingthe RS-232Cconversioncable(supplied)andacommercially availableRS-232straightcabletocontrolthemonitor fromthecomputer.

15. LAN terminal

• Youcancontrolthemonitorfromacomputeronanetwork byconnectingacommerciallyavailableLANcable betweenthisterminalandanetwork.

16. External speaker terminals

• Touseexternalspeakers,setSPEAKERSELECTto EXTERNALinAUDIOOPTIONontheSETUPmenu.

• Besuretouseexternalspeakerswithanimpedanceof6Ω orgreaterandaratedinputofatleast10W.

 1.Whilepushingthetab,insertthetipofthecable.  2.Releasethetab.

TIPS

• Besuretoconnectthe+and-terminalsandtheleftand rightspeakersproperly.

• Avoidshortcircuitingthe+and-terminals.

• WhenSPEAKERSELECTissettoEXTERNAL,the internalspeakersaredisabled.

17. USB cable

• TousetheUSBportonthefrontofthetray(forUSB device)(USB2.0compliant),connecttheUSBcableto theUSBportonthecomputer.

USB port (for USB device)



*Thetouchpanelmustbeconnectedseparately.

Computer

Page 14

Connecting the Power Cord

Caution

• Use only the power cord supplied with the monitor.

1. Turn off the main power switch.

2. Plug the power cord (supplied) into the AC input terminal.

3. Plug the power cord (supplied) into the AC power outlet.

For power outlet

Main power switch

Binding Cables

*1 *2

Power cord (Supplied)

The cables connected to the terminals on the rear of the monitor and the USB cable on the back of the tray can be fastened with the cable clamp.

AC input terminal

Cable clamp (insertion type)

Cable clamp attachment

Cable

Cable clamp attachment

Cable clamp

Cable

Page 15

Preparing the Remote Control Unit

Installing the batteries

1. Press the cover gently and slide it in the direction of the arrow.

2. See the instructions in the compartment and put in the

supplied batteries (R-6 (“AA” size) x 2) with their plus (+)

and minus (-) sides oriented correctly.

3. Close the cover.

TIPS

• When the batteries become exhausted, replace them with

new (commercially available) batteries.

• The supplied batteries (R-6 (“AA” size) x 2) may become

exhausted quickly depending on how they are stored.

• If you will not be using the remote control for a long time,

remove the batteries.

• Use manganese or alkaline batteries only.

Remote control operation range

The operation range of the remote control unit is approx. 16.4 feet (5 m) at an angle of approx 10° from the center to the top/ bottom/right/left of the remote control sensor.

Remote control sensor

16.4 feet (5 m)

10°10°

10°

TIPS

• Do not expose the remote control unit to shock by dropping

or stepping on it. This could lead to a malfunction.

• Do not expose the remote control unit to liquids, and do not

place it in an area with high humidity.

• The remote control unit may not work properly if the remote

control sensor is under direct sunlight or strong lighting.

• Objects between the remote control unit and the remote

control sensor may prevent proper operation.

• Replace the batteries when they run low as this may

shorten the remote control’s operation range.

• If a uorescent light is illuminated near the remote control

unit, it may interfere with proper operation.

• Do not use it with the remote control of other equipment

such as air conditioner, stereo components, etc.

Page 16

Removing the Handles

The handles can be removed.

Handle

Handle screws

Caution

• The removable handles and handle screws are for use with this monitor. Do not use them for any other devices.

• To attach handles, be sure to use the handles and handle screws which were removed from this monitor.

• Be sure the handles are attached securely.

Mounting a web camera

It is possible to mount a commercially available web camera in the following positions:

(1)

(1) Attach the supplied camera mount with the supplied

camera mount screws (x2).

(2) Attach the web camera to the camera mount with the

(2)

supplied camera screw (inch thread) (x1).

* The camera mount cannot be attached when the tray is

attached. To attach the camera mount, remove the tray

mount tting. (See page 68.)

Page 17

Turning Power On/Off

Caution

• Turn on the monitor rst before turning on the computer or

playback device.

• When switching the main power switch or the POWER

button off and back on, always wait for at least 5 seconds. A short interval may result in a malfunction.

Turning on the main power

Main power switch

Turning power off

Turning power off with monitor buttons

POWER button

1. Touch the POWER button.

The recognition screen appears.

2. Touch [OK].

The power is turned off. (Standby mode)

TIPS

• If about 15 seconds elapses while the recognition screen

appears, the power will automatically turn off.

Turning power off with remote control unit

Caution

• The main power must be turned on/off with the main power

switch. Do not connect/disconnect the power cord or turn the breaker on/off while the main power switch is on.

• For a complete electrical disconnection, pull out the main

plug.

Turning power on

Press the POWER button to turn the power ON.

Power LED POWER button

Status Status of the monitor

Green lit Power on Orange lit Power off (Standby mode) Green ashing Input signal waiting mode

1. Press the POWER button.

The power is turned off. (Standby mode)

TIPS

• When the main power switch is off, the monitor cannot be

turned on.

• If the monitor is in input signal waiting mode and you press

the POWER button, the monitor enters standby mode.

• Setting the SCHEDULE ashes the power LED alternately

in red and orange in standby mode.

• To disable the logo screen from displaying when turning the

power ON, set LOGO SCREEN to OFF on the OTHERS menu. (See page 35.)

TIPS

• You can x the input mode that appears after startup. Set

START INPUT MODE on the SETUP menu.

Page 18

Turning Power On/Off

ENTER

Operation mode

When the monitor is turned on for the rst time after being

shipped from the factory, the operation mode setting screen will be displayed. Set it to MODE1 or MODE2.

MODE1 ....OFF IF NO OPERATION is set to ON, and

STANDBY MODE is set to LOW POWER. (These settings can not be changed.) Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, or LAN for over 4 hours. Power consumption in standby mode is also minimized.

MODE2 ....Will perform standard operation.

OFF IF NO OPERATION is set to OFF, and STANDBY MODE is set to STANDARD. These

settings can be changed. Even after being set, changes can be made using OPERATION MODE, located in the menu of the monitor. (See page 33.)

Date/time setting

• If the time has yet to be set when the monitor is rst turned

on, the date/time setting screen appears. Set the date and time.

DATE/TIME SETTING

01 01 15/00 00

OK···[ENTER] CANCEL···[RETURN]

: :

:/ 20

1. Press or to select the date and time, and press

2. Press

• Be sure to set the date and time.

• The date/time setting screen will close automatically if

no operation is performed for about 15 seconds. The date and time can be set using DATE/TIME SETTING from the SETUP menu when the date/time setting screen disappears.

TIPS

•

Set the date in “Day/Month/Year” order.

•

Set the time on a 24-hour basis.

•

The clock is maintained by the internal battery.

•

If you already set the time but the date/time setting

or to change the numerical values.

screen appears when the power is turned on, the internal battery may be exhausted. Please contact your local SHARP servicing dealer or service center for assistance with battery replacement.

•

Estimated service life of the internal battery: About 5 years (depending on monitor operation)

•

The initial battery was inserted at the factory when the monitor was shipped, so it may run out of power before its expected operation life.

Page 19

Touch Panel / Touch Pen Preparations

Connecting the touch pen adapter

To use the touch pen, insert the touch pen adapter into the touch pen adapter port on the monitor.

Touch pen adapter port

Touch pen

adapter screw

Touch pen adaptor

(antitheft)

Touch Pen Preparations

Inserting the battery

2 touch pens are supplied. Insert the batteries in the touch pens.

1. Remove the battery cap.

2. Open the cover and insert the supplied battery (LR-03 (“AAA” size) x 1) into the touch pen.

Check the plus (+) and minus (-) markings on the inside

of the touch pen and insert the battery in the correct orientation.

Computer preparations

To use the touch panel, the touch pen and the eraser, install the software below.

• Touch Panel Settings Tool

• Touch Pen Utility

• Pen Software

To install the software, see the manual for each.

TIPS

• When the monitor is installed in the portrait orientation, the

operation of the touch pen, eraser, and pen software are not guaranteed.

Installed in portrait orientation

- The touch pen adapter does not need to be connected.

- The Touch Pen Utility and Pen Software do not need to be installed.

Calibration

If the touch position is out of place, perform position alignment. Perform calibration from the Touch Panel Settings Tool. For details, see the Touch Panel Settings Tool Operation Manual.

CAPACITIVE

Battery cap

3. Replace the cover and battery cap.

TIPS

• The supplied battery (LR-03 (“AAA” size)) may be

exhausted in a short time, depending on how it was stored.

• If the touch pen will not be used for an extended time,

remove the battery from the touch pen.

• For the battery, use an alkaline battery.

• You can afx the supplied ID labels to distinguish the touch

pens.

Page 20

Function button 2

Function button 1

Touch Panel / Touch Pen Preparations

Touch pen actions

Only use touch pens that are used with this monitor (supplied touch pens or optional PN-ZL03).

Pen tip

CAPACITIVE

Battery indicator

The factory default settings for the function buttons are as follows.

• Function button 1 : Pen Software Link

• Function button 2 : PageDown

• Function button 3 : PageUP

You can change the functions that are assigned to the function buttons. For details, see the Touch Pen Utility Operation Manual.

Using as a digitizer pen

A touch pen can be used as a Windows digitizer pen. To use a touch pen as a digitizer pen, change the “Input mode” to “Pen Digitizer” in the Touch Pen Utility. For details, see the Touch Pen Utility Operation Manual.

Function button 3

Touch pen settings

Touch pen settings are congured using the Touch Pen Utility.

For details on the settings and how to use the utility, see the Touch Pen Utility Operation Manual.

Adding touch pens (pairing)

• Up to 4 touch pens can be used simultaneously. (Up to 10

touch pens can be registered.)

• To use an optional touch pen with the monitor, the touch

pen must be registered in the touch pen adapter. (pairing)

Item Model Remarks

Touch pen PN-ZL03 For capacitive touch panel

Perform touch pen pairing for one pen at a time.

1. Click the Touch Pen Utility icon (

2. Click [Touch pen settings].

3. Select a line in the touch pen settings screen that does not have a pen registered, and touch [Registration].

) on the taskbar.

The function buttons are used differently when the pen is a digitizer pen. To use a function, touch the screen while holding down the button of that function.

TIPS

• Hold the touch pen at the part indicated below. Incorrect operation may result if your nger is too close to the tip of

the pen.

CAPACITIVE

• When the function button is pressed, the battery indicator

illuminates. If the battery indicator does not illuminate, check if the

battery is depleted.

• Use function buttons near the front of the screen. If too far

away, operation will not be possible.

• Press function buttons slowly and rmly. If pressed too

quickly, the action may not be recognized.

• The line may break if the touch pen battery is low or there

is other wireless equipment in operation nearby.

• If the pen tip becomes damaged and the touch panel does

not respond, replace the pen tip.

* When inserting the pen tip, insert rmly all the way in.

4. Simultaneously hold down function button 1 and function button 3 of the touch pen being paired for at least 5 seconds.

5. When the battery indicator blinks twice or more, release function button 1 and function button 3.

A message appears after completion of pairing.

6. Touch [OK].

TIPS

• When multiple touch pens are used, touch positions and

touch pen information (color, thickness, etc.) may become interchanged, and lines may break.

- When touched simultaneously

- When touch pens are moved near each other

- When batteries are low

- When other wireless equipment is operating nearby

• Do not press the pen tip on other than the screen.

This may cause malfunctioning.

• One touch pen cannot be registered in multiple touch pen

adapters.

• The pen tip is made soft to protect the screen and improve

writability. For this reason, the pen tip may become deformed, however, this is not a failure.

• The touch pens cannot be used as touch pens and digitizer

pens at the same time. When the setting is changed in the Touch Pen Utility, all touch pens become digitizer pens. Multiple digitizer pens cannot be used at the same time.

Page 21

Touch action

Touch actions that can be used with this monitor differ according to operating system and application. The functions of touch actions are also different. For details, check Windows Help and the application’s support documentation.

Touch Operation

Mode

Touch action

Single-tap

Double-tap

Swipe

Swipe from edge of screen

Drag-and-drop

Slide to pan

Flicks

Press-and-hold

Zoom

Press-and-tap

Rotate

* When “Recognize press and hold as right click” is set with

the Touch Panel Settings Tool. The action may be different from a mouse right-click in some cases.

Multi-Touch Mode Mouse Mode

Windows

8 / 8.1 / 10

Yes Yes Yes

Yes Yes No

Yes No No

Yes Yes Yes

Yes Yes No

Yes Yes Yes*

Yes Yes No

No Ye s No

Yes Yes No

Windows 7

Windows

7 / 8 / 8.1 / 10

Double-tap

Same action as double-clicking a mouse. Quickly touch twice with your nger/touch pen.

When double-tapping with your nger, be sure to lift your

nger sufciently off the screen after the rst tap. If there is insufcient distance between the screen and your nger,

double-tap will not take place.

Swipe

Touch the screen with your nger/touch pen, move without

lifting, and then stop.

TIPS

• In Windows 7, if the checkmark has been removed from

“Enable multi-touch gestures and inking” in “Pen and touch” in Control Panel, select the checkbox.

• For the procedures for using the touch pen in the Pen

Software, see the Pen Software Operation Manual.

Common nger and touch pen actions

Single-tap

Same action as left-clicking a mouse.

Touch with your nger/touch pen.

Swipe from edge of screen

After touching the edge of the monitor with your nger/touch pen, move horizontally without releasing your nger/touch pen

and then stop.

Page 22

Touch action

Drag-and-drop

Same action as drag-and-drop with a mouse. Touch the screen with your nger/touch pen and move without

lifting. When you have nished the movement, lift your nger/ touch pen.

Flicks

Flick your nger/touch pen in the direction of the function you want to use.

Flick your nger

Finger actions

Zoom

Use in a screen that is capable of enlargement/reduction.

Touch the screen with two ngers and move your ngers

closer together to reduce the view, or apart to enlarge the view.

Reduction

Press-and-hold

Same action as right-clicking a mouse.

Press briey with your nger/touch pen, and then lift your nger/touch pen from the screen.

Slide to pan

With your nger/touch pen touching the screen, move it up

and down to scroll the screen.

Enlargement

Press-and-tap

Same action as right-clicking a mouse.

With one nger touching the screen, tap once (single tap) with another nger.

Tap once (single tap) with another nger

With one nger touching

Page 23

Touch action

The main body

Rotation

Use this action in a screen that is capable of image rotation.

Touch the center point of the rotation with one nger. While holding that nger still, move another nger in the desired

direction of rotation.

Move another nger in the

desired direction of rotation

With one nger touching

TIPS

•

The screen may not respond correctly in the following cases:

Touch gesture is too quick The distance between the two points is too short The two points intersect

Other functions

In Windows 8/8.1/10, input panel functions can be used. In Windows 7, touch pointer and input panel functions can be used. For information on these functions, see Windows Help.

Touch pointer :

A translucent image of a mouse appears near the point touched. The left/right buttons of the image can be clicked to perform the same actions as left/right clicking a mouse.

Input panel :

A software keyboard and an input panel with handwriting recognition appear on the screen.

Windows 8/8.1/10 and Windows 7 (excluding Starter), the ink

function of Microsoft Ofce can be used.

Handwritten comments can be written, and handwriting can be recognized.

For details, see Microsoft Ofce Help.

Cautionary points

• Note the following when touching by nger:

- Do not touch with a wet nger.

- Touch with the ball of your nger.

- Touch with your bare nger.

The screen will not respond if you are wearing a glove.

• Do not use the touch pen for any purpose other than touch

panel operation.

• Do not press hard on the pen tip.

• This may not operate correctly if there is an inverter uorescent light nearby.

• Do not store with the pen tip of the touch pen or function

button pressed. The battery will be exhausted.

• If there is dirt or foreign matter on the tip of the touch pen,

remove it. Foreign matter may damage the screen.

• The touch pen position may occasionally deviate in the

• If the USB cable becomes disconnected, the touch

panel may not operate correctly after the USB cable is reconnected. In this case, restart the computer.

Eraser

Only use an eraser that is supplied with this monitor. The eraser is used with the Pen Software. For the procedure for using the eraser, refer to the Pen Software Operation Manual.

Caution

• Hold the main body of the eraser with your bare ngers.

The screen will not respond if you are wearing a glove.

• Slowly place the large face of the eraser fully on the screen. Insufcient contact may prevent the eraser from

being recognized. Touching the screen with one of the noncloth sides will damage the screen.

•

If there is any dirt or foreign matter on the surface that contacts the screen, remove it. Foreign matter may damage the screen.

• Place the eraser on the screen inside the display area. If the eraser rst touches the frame (outside the display area)

and then is moved inside the display area, the screen will not respond.

• When the “Input Mode” of the Touch Pen Utility is “Pen

Digitizer”:

- Even if you use the eraser in the Pen Software, the

eraser will be the standard size eraser.

- The eraser can be used in the software below.

Microsoft Ofce 2007/2010/2013

Page 24

Basic Operation

DISPLA

ENTER

RETURN

Using the touch menu

You can touch the monitor to change input mode, volume, and other settings.

1. Touch the TOUCH MENU button.

TOUCH MENU button

2. Touch the screen to change settings.

INPUT

SIDE INPUT TERMINAL

D-SUB2

HDMI2

HDMI3

BOTTOM INPUT TERMINAL

D-SUB1

DisplayPort

HDMI1

(4) (1) (2) (3)

(2) Volume adjustment

Changes the volume.

Increases the volume.

Decreases the volume. Mutes the sound.

Touch again to return the sound to the original volume.

(3) Touch action setting

Touch to disable touch action. Touch again to enable touch action.

TIPS

• When the input mode is changed, the disable touch

action setting is canceled.

• When TOUCH OUTPUT INVALID ICON is set to ON and

touch action is disabled, the TOUCH OUTPUT INVALID icon appears in the monitor.

(1) INPUT (Input mode selection)

Changes the input mode.

Input mode Video Audio

DisplayPort DisplayPort input terminal HDMI1 HDMI1 input terminal HDMI2 HDMI2 input terminal HDMI3 HDMI3 input terminal D-SUB1 D-sub1 input terminal D-SUB2 D-sub2 input terminal

• When the input mode is changed, the touch panel

connection also changes. You can set whether the side or bottom USB port is used in each input mode. (See page

32.)

*1 Select the terminal to be used in HDMI1 of INPUT

SELECT. (See page 31.)

*2 Select the terminal to be used in HDMI2 of INPUT

SELECT. (See page 31.)

*3 Select the terminal to be used in HDMI3 of INPUT

SELECT. (See page 31.)

*4 Select the terminal to be used in D-SUB1 of INPUT

SELECT. (See page 31.)

*5 Select the terminal for AUDIO SELECT which is used for

audio input. (See page 31.)

• You can touch the TOUCH OUTPUT INVALID icon in the

monitor to enable touch action.

• The position of the TOUCH OUTPUT INVALID icon can

be changed. (See page 33.)

• The TOUCH OUTPUT INVALID icon appears even when

a USB cable is not connected.

(4) Exit touch menu

Closes the touch menu.

TIPS

• The touch menu can also be used with the remote control

unit.

(1) Hold down

at least 5 seconds.

The touch menu appears. (2) Select the setting item with

(3) Set with

, and press

- The setting is entered.

- Press

to exit the touch menu.

Page 25

LAN

Basic Operation

Using the remote control unit

1. INPUT (Input mode selection)

The menu is displayed. Press mode, and press

* For the input modes that can be selected, see “Using the

touch menu” (See page 24.).

2. MUTE

Turns off the volume temporarily. Press the MUTE button again to turn the sound back to the previous level.

3. MENU

Displays and turns off the menu screen. (see page 27.)

4. VOL +/- (Volume adjustment)

Pressing menu screen is not displayed.

ENTER

to enter.

or displays the VOLUME menu when the

or to select the input

5. BRIGHT +/- (Backlight adjustment)

Pressing menu screen is not displayed.

Press or to adjust the brightness.

* If you do not press any buttons for about 4 seconds, the

BRIGHT menu automatically disappears.

6. ENTER

Conrms the setting.

7. RETURN

Returns to the previous screen.

8. SIZE (Screen size selection)

The menu is displayed. Press

9. DISPLAY

Displays monitor information.

The display changes from INFORMATION1 → INFORMATION2 → clear display, and so on every time you

press this button.

• The display disappears automatically after about 15

seconds.

•

• If

10. MODE (Color mode selection)

Each time you press this button, the color mode changes in the following order:

STD (Standard) → VIVID → sRGB → HIGH ILLUMINANCE → STD...

• sRGB applies to PC input only.

sRGB is international standard of color representation

specied by IEC (International Electrotechnical

Commission). Color conversion is made in taking account of liquid crystal’s characteristics and represents color tone close to its original image.

• HIGH ILLUMINANCE is a display with colors suited to

bright locations.

or displays the BRIGHT menu when the

BRIGHT 15

or to select the screen size. (See page 26.)

is displayed during LAN communication.

is displayed in red, there is a duplicate IP address.

Press or to adjust the volume of the sound.

* If you do not press any buttons for about 4 seconds, the

VOLUME menu automatically disappears.

* You can also change the setting by touch action.

Page 26

Basic Operation

Switching the screen size

Even when the screen size is changed, the display may remain the same depending on the input signal.

WIDE

ZOOM 1

ZOOM 2

NORMAL

Dot by Dot

PC input Displays image so it lls the entire screen.

AV input An image with a 4:3 aspect ratio is stretched to ll the entire

screen.

PC input An image with a 4:3 aspect ratio is enlarged to ll the entire screen

without changing the aspect ratio. The edges of the image may be

AV input

PC input Use this size if ZOOM 1 cuts off the subtitles.

AV input

PC input Displays image so it lls the screen without changing the aspect

AV input Displays the entire image of the aspect ratio of 4:3 without

PC input Displays the dots of the signals input from the connected PC as

AV input Displays the dots of the input signals as the corresponding dots on

cut off.

ratio of the input signals.

changing the aspect ratio.

the corresponding dots on the screen.

the screen.

TIPS

• Using this monitor’s screen-size switching or dual-screen display functions to compress or expand the screen for commercial

or public viewing in establishments like cafes or hotels may infringe on the rights of the creators, as protected by Copyright Law, so please be careful.

• When dual-screen display is selected, the screen size cannot be changed.

• The appearance of the original video may change if you select a screen size with a different aspect ratio than the original

image (e.g. TV broadcast or video input from external equipment).

• When an ordinary non-wide image (4:3) is viewed with the whole screen using the screen-size switching function of this

monitor, the edge of the image may be lost or appear distorted. If you wish to respect the creator’s intentions, set the screen size to “NORMAL”.

• When playing commercial software, parts of the image (like subtitles) may be cropped. In this case select the optimal screen

size using the screen-size switching function of this monitor. With some software, there may be noise or distortion at the edges of the screen. This is due to the characteristics of the software, and is not a malfunction.

• Depending on the original image size, black bands may remain at the edges of the screen.

Page 27

Menu Items

ENTER

RETURN

Displaying the menu screen

Video and audio adjustment and settings of various functions are enabled. This section describes how to use the menu items. See pages 28 to 35 for details of each menu items.

Caution

• Do not turn the main power switch off while the menu items

are being displayed. Doing so may initialize the settings.

Example of operation

(Adjusting CONTRAST in the PICTURE menu)

1. Press

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

PIP/PbyP

OTHERS

to display the menu screen.

SCREEN D-SUB1[RGB]

AUTO

CLOCK

PHASE

H-POS

V-POS

H-SIZE

V-SIZE

RESOLUTION SETTING

RESET

1 920x1080

V: 60 Hz H: 67.5 kHz

600

610

OK···[ENTER] BACK···[RETURN]

TIPS

• The menu will differ depending on the input mode.

• The menu screen will close automatically if no operation is

performed for about 15 seconds. (DATE/TIME SETTING, SCHEDULE and LAN SETUP screens will close in about 4 minutes.)

Menu screen display

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

PIP/PbyP

OTHERS

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

1 920x1080

30 30 30 12

V: 60 Hz H: 67.5 kHz

D-SUB1[RGB]

BACK···[RETURN]MOVE OSD···[DISPLAY]

1 Name of the menu 2 Input mode 3 An item being selected (highlighted) 4 Screen resolution of input signal, and other data.

2. Press

3. Press

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

PIP/PbyP

OTHERS

or to select PICTURE, and press

or to select CONTRAST.

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

1 920x1080

V: 60 Hz H: 67.5 kHz

30 30 30 12

4. Press or to adjust the setting.

SCREEN

PICTURE

AUDIO

SETUP

MONITOR

PIP/PbyP

OTHERS

PICTURE

BRIGHT

CONTRAST

BLACK LEVEL TINT COLORS SHARPNESS COLOR ADJUSTMENT ADVANCED RESET

1 920x1080

30 30 30 12

V: 60 Hz H: 67.5 kHz

D-SUB1[RGB]

BACK···[RETURN]MOVE OSD···[DISPLAY]

D-SUB1[RGB]

BACK···[RETURN]MOVE OSD···[DISPLAY]

TIPS

• Items that cannot be selected appear in gray. (e.g. Function not supported by the current input signal)

For items that have , press then press

5. Press

to close the menu screen.

, make settings and

Page 28

Menu Items

Menu item details

The menu will differ depending on the input mode.

SCREEN

You can move the menu screen display position each time

AUTO (D-SUB1[RGB]/D-SUB2)

The CLOCK, PHASE, H-POS, and V-POS are automatically adjusted. Pressing

computer screen for the rst time or when you change the setting of the computer. (See page 38.)

CLOCK (D-SUB1[RGB]/D-SUB2)

Adjusts frequency for sampling clock for applicable video.

Adjust when there is ickering in the form of vertical stripes.

When using the adjustment pattern (see page 38.), make adjustments so that no vertical stripe noise appears in it.

PHASE (D-SUB1[RGB]/D-SUB2)

Adjusts sampling clock phase for applicable video. Useful when small characters appear with low contrast and/or there are

ickers at corners. When using the adjustment pattern (see page 38.), make adjustments so that no horizontal stripe noise

appears in it.

H-POS

Adjust the horizontal position of the image.

V-POS

Adjust the vertical position of the image.

H-SIZE

Adjust the horizontal size of the image.

V-SIZE

Adjust the vertical size of the image.

RESOLUTION SETTING (D-SUB1[RGB]/D-SUB2)

H-RESOLUTION

V-RESOLUTION

RESET

Resets the values of the SCREEN menu items to the factory preset values. Select ON and then press

ENTER

performs adjustment. Use this automatic adjustment when you use the D-SUB1[RGB] or D-SUB2 to display a

Sets proper horizontal resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

Sets proper vertical resolution when the resolution of input signals is not recognized properly. (Adjustment may be impossible with some signals.)

ENTER

DISPLAY

is pressed.

Page 29

Menu Items

ENTER

PICTURE

You can move the menu screen display position each time

BRIGHT

Adjusts the backlight brightness. (In PIP mode, the main side setting is reected in the image.)

CONTRAST

Adjusts the difference between the bright and dark portions of the image.

BLACK LEVEL

Adjusts the entire brightness of the video signals.

TINT

Adjusts the hue. Selecting + changes the color towards green, and selecting - changes it towards magenta.

COLORS

Adjusts the color intensity.

SHARPNESS

Adjusts the sharpness of the image.

COLOR ADJUSTMENT

COLOR MODE

Changes the color mode on the screen. The color mode on the screen can also be changed using a remote control unit. (See page 25.) * sRGB is PC input only. See page 25 for details.

(In PIP mode, the main side setting is reected in the image.)

WHITE BALANCE

THRU ..............Displays the input signal level as is. (for PC input only)

PRESET .......... Selects the color temperature using PRESET.

USER .............. Used for adjusting R-/G-/B-CONTRAST and R-/G-/B-OFFSET respectively.

(In PIP mode, the main side setting is reected in the image.)

PRESET

Selects the color temperature when the WHITE BALANCE is set to PRESET. The setting values are shown for reference. The color temperature of the screen varies over time. This function is not intended to keep the color temperature constant.

USER

Adjusts each item when the WHITE BALANCE is set to USER.

R-CONTRAST .... Adjusts bright-toned red component.

G-CONTRAST ... Adjusts bright-toned green component.

B-CONTRAST .... Adjusts bright-toned blue component.

R-OFFSET ......... Adjusts dark-toned red component.

G-OFFSET ......... Adjusts dark-toned green component.

B-OFFSET ......... Adjusts dark-toned blue component.

COPY TO USER

Copies the value of PRESET to the USER setting. Select ON and then press (In the case other than white, color tone may differ from the PRESET.)

GAMMA

Selects the gamma. USER sets the gamma to the sent value (see page 42).

(In PIP mode, the main side setting is reected in the image.)

FLESH TONE (AV input)

Adjust the hue control. When FLESH TONE is set to LOW or HIGH, C.M.S.-HUE/-SATURATION/-VALUE cannot be set.

C.M.S.-HUE (AV input)

Adjusts color tone with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

C.M.S.-SATURATION (AV input)

Adjusts color vividness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

C.M.S.-VALUE (AV input)

Adjusts color brightness with 6 colors of R (red), Y (yellow), G (green), C (cyan), B (blue), and M (magenta).

DISPLAY

is pressed.

Page 30

Menu Items

ENTER

ADVANCED

AUTO (D-SUB1[RGB]/D-SUB2)

The ANALOG GAIN and ANALOG OFFSET are automatically adjusted. Pressing

ANALOG GAIN (D-SUB1[RGB]/D-SUB2)

Adjusts the bright portions of the video input signal.

ANALOG OFFSET (D-SUB1[RGB]/D-SUB2)

Adjusts the dark portions of the video input signal.

3D-NR (AV input)

Reduce the noise of playback images on video. Setting a higher level reduces more noise. However, it may cause blurring on an image.

MPEG-NR (AV input)

Reduce block noise caused by digital compression.

3D-Y/C (D-SUB1[VIDEO])

Specify whether to perform 3-dimension Y/C separation. If dot interference or cross-color is occurring in fast-motion scenes, selecting OFF may improve the image quality.

RGB INPUT RANGE (HDMI[PC]/HDMI[AV]/D-SUB1[RGB]/D-SUB2/DisplayPort)

Sets the RGB input signal range. When using HDMI or DisplayPort set to AUTO, the RGB input signal range is detected automatically. Use AUTO normally. If the RGB input signal range cannot be set appropriately even when using AUTO, set according to the image. When the setting is different, images will be displayed with washed out blacks and compressed gradients.

ACTIVE CONTRAST (AV input)

Automatically adjusts the contrast according to the image.

(In PIP mode, the main side setting is reected in the image.)

The adjustment operation may not be smooth depending on the image. In this case select OFF.

DISPLAY COLOR PATTERN

Displays a color pattern. Can be displayed while the menu screen is displayed, so you can refer to the pattern while adjusting the image.

OFF ...............No pattern display.

WHITE ...........White single color pattern display.

RED...............Red single color pattern display.

GREEN .........Green single color pattern display.

BLUE .............Blue single color pattern display.

USER ............Red/green/blue mixed color pattern display. When USER is selected, set each color’s level.

RESET

Resets the values of the PICTURE menu items to the factory preset values. Select ON and then press

performs adjustment.

Page 31

Menu Items

ENTER

AUDIO

TREBLE

Adjusts the volume of treble-level sound.

BASS

Adjusts the volume of bass-level sound.

BALANCE

Adjusts the balance of the audio sound between right and left.

RESET

Resets the values of the AUDIO menu items to the factory preset values. Select ON and then press

SETUP

DATE/TIME SETTING

Set the date and time. Press Set the date in “Day/Month/Year” order. Set the time on a 24-hour basis. (Factory default)

DATE/TIME FORMAT

Sets the date/time display format.

DATE ..................MM/DD/YYYY, DD/MM/YYYY, YYYY/MM/DD

TIME ...................Select 12- or 24-hour time.

SCHEDULE (See page 37.)

You can turn the power on/off and change the screen brightness at a specied time.

LANGUAGE

Sets the display language for the menu screen.

INPUT SELECT

HDMI1/HDMI2/HDMI3

Select the input mode to be used in HDMI1, HDMI2 and HDMI3 input terminals.

D-SUB1

Select the input mode to be used in D-Sub1 input terminal. Select SET after selecting the input mode, and then press

HDMI AUTO VIEW

When ON is selected, the screen size is adjusted automatically according to the screen size control signal included in the video signal input from the AV HDMI input terminal.

HOT PLUG CONTROL

Sets whether to use hot plug control for the HDMI1, HDMI2, and HDMI3 input terminals.

INPUT MODE NAME

For each terminal, you can change the input mode name that is displayed during input mode selection and display.

AUDIO SELECT

Selects the terminal used to input audio signals in each input mode.

AUDIO OPTION

SPEAKER SELECT

Selects the speaker to be used.

AUDIO OUTPUT

Sets the volume of sound output from the audio output terminals. When set to VARIABLE 2, sound will not be output from the built-in speaker or the external speaker terminal.

VARIABLE1 ........ You can adjust the volume using VOLUME.

VARIABLE2 ........ You can adjust the volume using VOLUME.

FIXED................. Fixes the sounds.

AUDIO INPUT LEVEL 1/2

Selects the maximum audio input level of the audio input 1, 2 terminals.

MONAURAL AUDIO

Outputs audio signals as monaural.

(YYYY: Year, MM: Month, DD: Day)

to select the date and time, and press or

to change the numerical values.

ENTER

Page 32

Menu Items

TOUCH INPUT SELECT

These settings enable use of the touch panel according to input mode selection.

BOTTOM USB

Sets the input mode for use of the touch panel, which is connected to the USB port at the bottom of the monitor. In the landscape orientation, select the terminal into which the video signal of the computer connected to the USB 1 port will be input. When BOTTOM INPUT TERM. is selected and the input mode is DisplayPort, HDMI1, or D-SUB1, the touch panel can be used with the computer connected to the USB 1 port. In the portrait orientation, select the terminal into which the video signal of the computer connected to the USB 2 port will be input. When BOTTOM INPUT TERM. is selected and the input mode is HDMI2, HDMI3, or D-SUB2, the touch panel can be used with the computer connected to the USB 2 port. When “-” is selected, the touch panel cannot be used.

SIDE USB

Sets the input mode for use of the touch panel, which is connected to the USB port at the side of the monitor. In the landscape orientation, select the terminal into which the video signal of the computer connected to the USB 2 port will be input. When SIDE INPUT TERM. is selected and the input mode is HDMI2, HDMI3, or D-SUB2, the touch panel can be used with the computer connected to the USB 2 port. In the portrait orientation, select the terminal into which the video signal of the computer connected to the USB 1 port will be input. When SIDE INPUT TERM. is selected and the input mode is DisplayPort, HDMI1, or D-SUB1, the touch panel can be used with the computer connected to the USB 1 port. When “-” is selected, the touch panel cannot be used.

START INPUT MODE

You can set the input mode that will be in effect when the power is turned on. When this is set to LAST INPUT MODE, the input mode when the power was last turned off will appear.

* When NO SIGNAL AUTO INPUT SEL is ON and there is no input signal in the set input mode, the input mode will change to

the input mode that has an input signal.

COMMUNICATION SETTING

RS-232C/LAN SELECT

Selects the method with which to control the monitor from the computer.

BAUD RATE

Selects the communication speed used for RS-232C communication.

LAN SETUP

Congures the settings to control the monitor from the computer via LAN. (See page 51.)

Page 33

Menu Items

MONITOR

Select the installation direction of the monitor.

LANDSCAPE ............Landscape orientation

PORTRAIT ...............Portrait orientation

OSD H-POSITION

Adjusts the horizontal display position of menu screen.

OSD V-POSITION

Adjusts the vertical display position of menu screen.

OPERATION MODE

MODE1 ......OFF IF NO OPERATION is set to ON, and STANDBY MODE is set to LOW POWER.

MODE2 ......Will perform standard operation. OFF IF NO OPERATION is set to OFF, and STANDBY MODE is set to

STANDBY MODE

When STANDARD is selected, startup time from standby mode is reduced. Note, however that, more power will be consumed in standby mode. When LOW POWER is selected, current consumption is reduced while the monitor is in standby mode. Note, however, that the startup time from standby mode becomes longer. When LOW POWER is set, RS-232C/LAN control are not possible in standby mode.

OFF IF NO OPERATION

Determines whether or not to set the monitor to go into standby mode when there is no operation from the remote control unit, RS-232C commands, or LAN for over 4 hours.

POWER ON DELAY

If POWER ON DELAY is set to ON, you can delay the screen display after the monitor is turned on. When ON is selected, set the delay time with INTERVAL (interval can be set up to 60 seconds in units of 1 second).

When this function is activated, the power LED ashes (at approx. 0.5 second interval) in green.

SELF ADJUST

On a D-SUB1[RGB]/D-SUB2 screen, specify whether to perform screen adjustment automatically or not. When ON is selected, the screen is automatically adjusted when its resolution is 800 x 600 or higher and the timing of input signals changes. “ADJUSTING” appears on the screen during the adjustment. If SELF ADJUST is set to ON, set the time it takes to start the SELF ADJUST function in START TIMING. For images with black edges, etc., depending on the signal, adjustment may not be possible. In this case select OFF. (Perform manual adjustment of the screen.)

TOUCH PANEL

TOUCH OUTPUT INVALID DISP.

TOUCH OUTPUT INVALID ICON ......

CHANGE DISPLAY POSITION .......... Sets the display position of the TOUCH OUTPUT INVALID icon.

TOUCH OPERATION MODE

Select the touch mode.

AUTO ................................................. Automatically switches between MOUSE MODE and MULTI-TOUCH MODE.

MOUSE MODE .................................. Touch information is output as mouse information.

MULTI-TOUCH MODE ....................... Touch information is output as digitizer information.

(These settings can not be changed.)

STANDARD. These settings can be changed.

Sets whether the TOUCH OUTPUT INVALID icon is displayed when touch action is disabled.

* If Touch Panel Settings Tool is installed on your computer, set with the Touch Panel Settings Tool.

* The touch panel must be connected in order to congure this setting.

TOUCH PANEL MODE (PC input)

When the resolution is 1920 x 1080, setting this to ON improves touch panel tracking. When two screens are displayed, or when V-POS or V-SIZE is adjusted on the SCREEN menu, the screen may become distorted. In this event, set to OFF.

Page 34

Menu Items

PIP/PbyP

PIP MODES

Sets the display method.

OFF ...........Displays one screen.

PIP .............Displays a sub screen inside a main screen.

PbyP ..........Displays a main screen and a sub screen in a line.

PbyP2 ........Displays a main screen which measures 1280 pixels in the longest direction and a sub screen in a line.

PIP SIZE

Sets the size of the sub screen in PIP mode.

PIP H-POS

Adjusts the horizontal position of the sub screen in PIP mode.

PIP V-POS

Adjusts the vertical position of the sub screen in PIP mode.

PIP BLEND

In PIP mode, use this menu item to display the sub screen transparently.

PIP SOURCE

Selects the input signal of the sub screen in PIP, PbyP, or PbyP2 mode.

SOUND CHANGE

Sets the sound which is output in PIP, PbyP, or PbyP2 mode. If the main screen is displayed as a full screen by the AUTO OFF function, the sound for the main screen is output even when

the sound for the sub screen is specied.

MAIN POS

Sets the position of the main screen in PbyP or PbyP2 mode.

PbyP2 POS

Sets the position of the sub screen in PbyP2 mode.

AUTO OFF

Sets the display method when no signals for the sub screen are input in PIP, PbyP, or PbyP2 mode.

MANUAL .... Displays a main screen and a black sub screen.

AUTO .........Displays the main screen as a full screen.

Page 35

Menu Items

OTHERS

SCREEN MOTION

PATTERN

Residual images are reduced by moving the screen.

OFF ................. SCREEN MOTION function is disabled.

PATTERN1 ...... The whole screen moves vertically and horizontally.

PATTERN2 ...... A black screen spreads from the bottom of the screen and then shrinks to the bottom of the screen. If the

PATTERN3 ...... A black bar moves from the left end to the right end of the screen. If the monitor is installed in the portrait

PATTERN4 ......

monitor is installed in the portrait orientation, a black screen spreads from the right end of the screen and then shrinks to the right end of the screen.

orientation, a black bar moves from the top to the bottom of the screen. Black screens appear from both the top and bottom of the screen, and the displayed image is compressed into the

central eld. If the monitor is installed in the portrait orientation, the screen is compressed from the left and right ends.

PATTERN1 PATTERN2

MOTION TIME 1

Specify a time period (operating interval) until SCREEN MOTION starts.

MOTION TIME 2

Specify a time period during which SCREEN MOTION operates (time period during which the screen will move).

POWER MANAGEMENT

POWER MANAGEMENT determines whether or not to switch modes from no signal to the input signal waiting mode.

CONNECT AUTO INPUT SELECT

Sets whether the input into the input terminal automatically changes when a video signal is input into that terminal. (With some input signals, the input may not change.)

NO SIGNAL AUTO INPUT SEL.

Specify whether to change inputs automatically. When ON is selected and no signal is present in the selected input mode, the monitor automatically changes the selected mode to another mode where a video signal is present. When there are video signals in multiple input modes, switching takes place according to the order of priority set in AUTO INPUT SELECT PRIORITY.

AUTO INPUT SELECT PRIORITY

Sets the order of input terminal priority for NO SIGNAL AUTO INPUT SEL.. Input does not change automatically for terminals without a priority setting.

LOGO SCREEN

Sets whether or not to display the logo screen.

INPUT SIGNAL (D-SUB1[RGB]/D-SUB2)

If the resolution of the computer is one of the following, make a selection from the following options.

480 LINES .......... AUTO, 640x480 or 848x480

768 LINES .......... AUTO, 1024x768, 1280x768, or 1360x768

1050 LINES ........ 1400x1050 or 1680x1050

ZOOM2 SPECIAL SETTING (See page 36.)

SCAN MODE (AV input)

Sets the scan mode used for AV mode input.

MODE1 ............... Over-scan display

MODE2 ............... Under-scan display

MODE3 ............... Under-scan display when the input signal is 1080i/p. Otherwise, over-scan display

Even when MODE1 is selected, under-scan display is used when the input signal is 1080i/p and the screen size is Dot by Dot.

COLOR SYSTEM (D-SUB1[VIDEO])

Select the color system of the AV equipment which is connected to D-sub1 input terminal. (AUTO / PAL / PAL-60 / SECAM / NTSC3.58 / NTSC4.43) When AUTO is selected, the color system is automatically set according to the input signal.

PATTERN4PATTERN3

TIPS

• When WHITE BALANCE is set to THRU, BLACK LEVEL, CONTRAST, TINT, COLORS, RGB INPUT RANGE, GAMMA and

COPY TO USER cannot be set.

• If COLOR MODE is set to sRGB, the following items cannot be set.

WHITE BALANCE, PRESET, USER, COPY TO USER, and GAMMA

• When the COLOR MODE is set to VIVID or HIGH ILLUMINANCE, GAMMA can not be adjusted.

• STANDBY MODE cannot be set to LOW POWER when SCHEDULE is effective.

• When displaying the color pattern, it is possible to adjust certain items of the PICTURE menu.

Non-adjustable items cannot be selected.

Page 36

Menu Items

Dual screen display

You can display two screens simultaneously. Set this function with “PIP MODES” in the PIP/PbyP menu.

PIP

PbyP

PbyP2

Main screen

Main

screen

Main screen

Sub

screen

Sub

screen

A sub screen is displayed inside a main screen.

A main screen and a sub screen are displayed in a line.

Displays a main screen which measures 1280

Sub

pixels in the longest direction and a sub screen in a line.

* The currently selected input signal is displayed on the main

screen.

* The following combinations are available for display:

DisplayPort - D-SUB1, D-SUB2 HDMI1, HDMI2, HDMI3 - D-SUB1, D-SUB2

TIPS

• You might infringe on a copyright of the author which is

protected by copyright law when you display the images of the computer screen and television/VCR simultaneously for

prot-making or to show the image to the public.

• The screen size for dual-screen display is the same as

the screen size for single-screen display. The Dot by Dot screen is displayed in NORMAL size except when it is set as the PIP main screen.

• When dual-screen display is selected, the SCREEN

MOTION function is disabled.

• When dual-screen display is selected, the CONNECT

AUTO INPUT SELECT function and NO SIGNAL AUTO INPUT SEL. function are disabled.

• When dual-screen display is selected, the INPUT SELECT

options cannot be set.

• When dual-screen display is selected, the AUDIO menu

cannot be set.

• When an interlaced signal (1080i, 480i, video) is input to the sub screen, horizontal lines may icker. If this happens,

display the image on the main screen.

• Touch operation cannot be used in the sub screen.

ZOOM2 SPECIAL SETTING

If you connect a laptop computer with any of the following screen resolutions and black bands appear around the screen, set ZOOM2 SPECIAL SETTING of INPUT SIGNAL on the OTHERS menu to ON and then select ZOOM2 in the SIZE setting. This displays the area inside the black band.

Laptop computer

Corresponding signal*

resolution 1280x800 1280x1024, 1280x960, 1400x1050*

1280x600 1280x720

1024x600 1024x768

*1: This setting is effective only when the screen resolution,

including the black band, is one of the resolutions listed above.

*2: Use the automatic screen adjustment.

Page 37

ENTER

Menu Items

SCHEDULE

You can set the time to switch the monitor on and off. Set this function with “SCHEDULE” in the SETUP menu. (See page 31.)

SCHEDULE

(1)

No.

– –

– – – – – –

1920x1080

– –/– –/– – – – – – –

(2) (3) (4)

POWER DAY OF THE WEEK

– – – – – –

– – – – – – – – – – – – –

– – – – – – – – – – – – – – – – – – – – – – – – – – – – – –

– –:– –:– –

V: 60 Hz H: 67.5 kHz

TIME

– – – –

– – – ––

OK···[ENTER] CANCEL···[RETURN]

D-SUB1[RGB]

(5)

INPUT BRIGHT

(6)

– – – – – – – –

– – – – – – – – – – – – – – – – – – – – – – – –

1. Press or to select the SCHEDULE number, and press

2. Set the SCHEDULE. (See the description below.)

Press

or to select items, and press or to

change the setting.

3. Press

SCHEDULE becomes effective.

Caution

• Donotswitchoffthemainpoweraftersettingthe

SCHEDULE.

• Specifythecorrectdateandtime.(Seepage31.)

SCHEDULE does not function unless the date and time are

specied.

• Checkregularlythatthesetdateandtimearecorrect.

• When STANDBY MODE is LOW POWER, SCHEDULE

cannot be set.

• Whenatemperatureabnormalityoccursandthebacklight

brightness is reduced, the brightness is not changed even

ifaschedulesettoBRIGHTisexecuted.

TIPS

• Upto8SCHEDULEitemscanberegistered.

• SettingtheSCHEDULEashesthepowerLEDalternately

in red and orange in standby mode.

• ASCHEDULEthathasalargenumberhasprecedence

over that of a small number when schedules overlap.

(1)

●:SCHEDULEeffective

:SCHEDULEnoteffective

(2) POWER

ON :Switchesthemonitoronatthespeciedtime. OFF:Switchesthemonitoroffatthespeciedtimeandputs

the monitor in standby mode.

(3) DAY OF THE WEEK

SpeciesthedayoftheweektoexecutetheSCHEDULE. 0:ONLY ONCE

ExecutestheSCHEDULEonceonthespeciedday. SpecifythedayoftheweektoexecutetheSCHEDULE.

1:EVERY WEEK

ExecutestheSCHEDULEonthespecieddayoftheweek everyweek.Specifythedayoftheweektoexecutethe

SCHEDULE. Periodic setting such as “Monday through Friday” is also possible.

2:EVERY DAY

ExecutestheSCHEDULEeverydayregardlessoftheday oftheweek.

(4) TIME

SpeciesthetimetoexecutetheSCHEDULE.

Set the time on a 24-hour basis. (Factory default) Can be entered as 12-hour time using the TIME setting in DATE/TIME FORMAT.

(5) INPUT

Speciestheinputmodeatpower-on.Ifnotspecied,the

START INPUT MODE setting will apply. By factory default, the input that was active when the power was last turned off will appear. Input modes displayed on HDMI1, HDMI2, HDMI3 and D-SUB1 will depend upon the INPUT SELECT settings.

(6) BRIGHT

Sets the brightness when changing the screen brightness at

aspeciedtime.

Page 38

Menu Items

Adjustments for PC screen display

Automatic adjustment

When you use D-SUB1 or D-SUB2 to display a computer

screen for the rst time, or when you change the setting of the

computer, use the automatic screen adjustment.

1. Switch the input to D-SUB1 or to D-SUB2 and display the adjustment pattern. (See the description below.)

2. Press

3. Press

4. Press

The automatic adjustment is complete in several seconds.

5. Press

• If the screen cannot be adjusted properly with one

Before making adjustments in the SCREEN menu or PICTURE menu, display an image to brighten the entire screen. If you are using a Windows PC, use the adjustment pattern on the supplied CD-ROM.

and use or to display the SCREEN

menu.

ENTER

and select “AUTO”.

ENTER

to close the menu screen.

TIPS

automatic adjustment, repeat the automatic adjustment two or three times. Try manual adjustment if necessary.

Screen display for adjustment

Opening the adjustment pattern

The following example is performed in Windows 7.

1. Load the supplied CD-ROM into the computer’s CDROM drive.

2. Open [CD Drive] in [Computer].

3. Double-click [Adj_uty.exe] in the [Monitor] folder.

The adjustment pattern will appear. Adjust the screen automatically or manually.

4. When adjustment is nished, press the [Esc] on the

computer’s keyboard to quit the adjustment program.

5. Eject the CD-ROM from the CD-ROM drive.

TIPS

• If the display mode on the computer you are using is

65,000 colors, the color levels in the color pattern may appear differently or grayscale may appear to be colored.

(This is due to the specications of the input signal and is

not a malfunction.)

Page 39

Initialization (Reset)/Functional Restriction Setting (FUNCTION)

RETURN

You can return the settings to their factory-preset values and restrict operations.

SIZE

1. Hold

down until “F” appears in the upper left

corner of the screen.

2. While “F” appears, press

, , , in that

order.

FUNCTION

▲

ALL RESET

ADJUSTMENT LOCK

ADJUSTMENT LOCK TARGET

RS-232C/LAN OSD DISPLAY LED TEMPERATURE ALERT

STATUS ALERT POWER BUTTON

EXTERNAL CONTROLLER INPUT

OK…[ENTER] END…[RETURN]

▲▲▲▲▲▲▲

UNLOCKED

OFF

ON 1

ON LED OFF

MONITOR

▲ ▲▲▲▲▲▲

3. Select and set the items.

ALL RESET

Resets the settings to the factory default settings.

ENTER

Press

ENTER

, select the resetting method, and then press

ALL RESET1 ....Resets all the settings to the factory

default settings.

ALL RESET2 ....Returns all settings to the factory default

settings except for the following items: LAN SETUP, RS-232C/LAN SELECT, BAUD RATE, NETWORK, MAIL, SERVICE & SUPPORT, and SNMP (See page 32, and pages 55 to 58.)

ADJUSTMENT LOCK

You can disable operations on the monitor and the remote control unit that use buttons. OFF ...Enables operation. ON 1 .. Disables all operations other than turning power

on/off and FUNCTION.

ON 2 .. Only the FUNCTION operation is enabled.

Disables all operations other than FUNCTION (not even power on/off). When STANDBY MODE is set to LOW POWER, ON 2 cannot be set.

ADJUSTMENT LOCK TARGET

Sets the target to prohibit operation of with ADJUSTMENT LOCK.

REMOTE CONTROL ..... Prohibits remote control

operation

MONITOR BUTTONS ... Prohibits monitor button

operation

BOTH ............................. Prohibits remote control and

monitor button operation

RS-232C/LAN

Species whether to allow control via RS-232C or LAN

(see pages 40 and 51).

OSD DISPLAY

Shows/hides the menu, modes and messages. The FUNCTION screen cannot be hidden.

ON 1 .............. Shows all menus, modes and messages.

ON 2 .............. Hides messages automatically displayed

by the display. Shows messages during operation.

OFF ............... Hides all menus, modes and messages.

LED

Species whether to light the power LED.

TEMPERATURE ALERT

Selects the notication method for an abnormal

temperature.

OFF .............. Do not notify about an abnormal

temperature.

OSD & LED .. When an abnormal temperature is

detected, the power LED ashes in red

and green alternately and the screen displays a message: TEMPERATURE.

LED............... When an abnormal temperature is

detected, the power LED ashes in red

and green alternately.

STATUS ALERT

Selects the notication method for a hardware error.

OFF .............. Do not notify about the error.

OSD & LED .. When a hardware error is detected, the

power LED ashes in red and the screen

displays a message: STATUS [xxxx].

LED............... When a hardware error is detected, the

power LED ashes in red.

POWER BUTTON

Normally, leave this setting as MONITOR. When using an optional part, if instruction appears, change the setting accordingly.

EXTERNAL CONTROLLER INPUT

Normally, you do not need to change this setting. When using an optional part, if instruction appears, change the setting accordingly.

4. Press

TIPS

to return to the normal screen.

• When both abnormal temperature and hardware error are detected, the hardware error notication overrides.

• If TEMPERATURE ALERT or STATUS ALERT is set to

OSD&LED, alert messages will appear even if the OSD DISPLAY is set to ON 2 or OFF.

• If TEMPERATURE ALERT or STATUS ALERT is set to LED

or OSD & LED, the LED lights even if the LED function is set to OFF.

Page 40

Controlling the Monitor with a PC (RS-232C)

Return code

You can control this monitor from a PC via RS-232C (COM port) on the PC.

TIPS

• To control the monitor via RS-232C, set RS-232C/LAN

SELECT to RS-232C.

• When STANDBY MODE is set to LOW POWER, control is

not possible in standby mode.

• You cannot use RS-232C and LAN control simultaneously.

PC connection

Connect the RS-232C conversion cable (supplied) to the RS232C input terminal on the monitor. Connect the RS-232C conversion cable (supplied) to the COM port (RS-232C port) on your computer with an RS-232 cable (straight).

RS-232C input terminal

Computer

To COM port

Communication conditions

Set the RS-232C communication settings on the PC to match the monitor’s communication settings as follows:

Baud rate *

Data length 8 bits Flow control None

Parity bit None

* Set to the same baud rate as the BAUD RATE setting of

SETUP menu. (Initial setting: 38400 bps)

Stop bit

1 bit

Communication procedure

Command format

When a command is sent from the PC to the monitor, the monitor operates according to the received command and sends a response message to the PC.

C1 C2 C3 C4 P1 P2 P3 P4

Command field

(4 prescribed

alphanumerical characters)

Example: VOLM0030 VOLM

Parameter field

(4 character string comprised of:

0-9, +, -, space, ?)

RS-232 straight cable (commercially available)

RS-232C conversion cable (supplied)

* Be sure to input 4 characters for the parameter. Pad with

spaces (“ (“ Wrong : VOLM30 Right : VOLM 30

When inputting a negative value, specify a numerical value in three digits.

Example: AUTR-005

Do not use spaces for MPOS, DATE, and SC01 through

SC08. Specify parameters using a specied number of

characters.

Example: MPOS010097

If a command has “R” listed for “DIRECTION” in the “RS-232C command table” on page 43, the current value can be returned by using “?” as the parameter.

Example:

VOLM ? ? ? ? ←

30 ←

”) if necessary.

” is a return code (0DH, 0AH or 0DH))

From PC to monitor (How much is current volume setting?).

From monitor to PC (Current volume setting: 30).

Page 41

Controlling the Monitor with a PC (RS-232C)

VOLM0020

Response code format

When a command has been executed correctly

O K

A response is returned after a command is executed.

When a command has not been executed

R R E

TIPS

• “ERR” is returned when there is no relevant command or

when the command cannot be used in the current state of the monitor.

• If communication has not been established for reasons

such as a bad connection between the PC and monitor, nothing is returned (not even ERR).

• “ERR” may be returned when a command cannot be

received correctly due to interference from the surrounding environment. Please ensure that the system or software retries the command if this occurs.

Return code (0DH, 0AH)

Communication interval

• After OK or ERR is returned, you must send the following

commands.

To set a timeout for the command response, specify 10

seconds or longer.

• Provide an interval of 100 ms or more between the

command response and the transmission of the next command.

Interval of 100 ms or more

INPS0001 WAIT OK

TIPS

• When executing ALL RESET, set the timeout period to 30

seconds or longer.

• When turning the power on while the POWER ON DELAY

function is in use, set the timeout period to the POWER ON

DELAY period + 10 seconds or longer.

If execution of the command is taking some time

I W T A

When the following commands are used, “WAIT” is returned. In this case, a value will be returned if you wait a while. Do not send any command during this period.

• Commands which return WAIT:

RSET, INPS, ASNC, WIDE, PXSL, POWR, AGIN, MWIN, MWIP, MWPP

When control via RS-232C is locked (see page 39)

E C D K O L

When RS-232C/LAN SELECT is set to LAN

U N S E L E C T E D

Return code (0DH, 0AH)

Return code (0D

H, 0AH)

Return code

H, 0AH)

(0D

Page 42

Controlling the Monitor with a PC (RS-232C)

…

UGRW01000000010002 … 0031C0

Command

Block number

32 pieces of data Checksum

Setting of the GAMMA user data

To transfer the GAMMA user data

Use the user data transfer commands (UGRW, UGGW and UGBW). For each of the R, G and B colors, divide the total 512 pieces of user data into 16 blocks, and transfer 32 pieces of data with each command.

C1 C2 C3 C4 P1 P2 P3 P4

Command field

Example: To transfer the data of block 1 (0 to 31 levels)

of red (R) data

* If data is less than 4 digits, add a “0” (zero) to make it 4

digits.

* The checksum eld is the character string (ASCII) data of

lower-order one byte which indicates the sum of the block number and 32 pieces of data in hexadecimal (0 to F).

Saving the GAMMA user data

Use the user data save command (UGSV) to save the transferred user data in the monitor. If the data is not saved, it will be cleared when:

• The main power switch is off

• STANDBY MODE is LOW POWER and the monitor enters

standby mode

Block number (01 to 16)

One piece of data consists

of 4 digits.

Data fieldChecksum field

S1 S2

Activating the GAMMA user data

To activate the transferred user data, select USER for GAMMA of the PICTURE menu, or send the corresponding RS-232C command.

Checking the GAMMA user data

Use the user data read commands (UGRR, UGGR and UGBR) to return 512 pieces of user data for each of the R, G and B colors. Divide the data into 16 blocks and return 32 pieces of data with each command. The value to be returned is not the value stored in the monitor, but the value in the temporary memory for display. (These values are the same when the user data save command (UGSV) above has been sent.)

TIPS

• The user data is not initialized by RESET of the PICTURE

menu. To initialize the user data, use ALL RESET of the FUNCTION menu. The GAMMA user data initialize command (UGRS) allows the initialization of the user data only.

Page 43

Controlling the Monitor with a PC (RS-232C)

RS-232C command table

How to read the command table

Command: Command eld (See page 40.) Direction: W When the “Parameter” is set in the parameter eld (see page 40), the command functions as described

R The returned value indicated under “Reply” can be obtained by setting “????” or “

Parameter: Parameter eld (See page 40.)

Reply: Response (Returned value) * : When "STANDBY MODE" is set to "STANDARD":

When "STANDBY MODE" is set to "LOW POWER":

Power control/Input mode selection

Function

POWER CONTROL POWR W 0

INPUT MODE SELECTION INPS W 0 Toggle change for input mode. Terminals not selected in INPUT SELECT cannot

under “Control/Response Contents”.

?” in the

parameter eld (see page 40).

“○” : Indicates a command which can be used in standby mode or when the power is on.

“–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.

“○/–” : Indicates a command which can be used when the power is on. Cannot be used in standby mode.

Command Direction

R 0 Standby mode

R 2 D-SUB1[RGB]

Parameter Reply Control/Response contents *

Switches to standby mode.

1 Enters the power ON state.

2 D-SUB1[RGB]

3 D-SUB1[COMPONENT]

4 D-SUB1[VIDEO]

9 HDMI1[AV]

10 HDMI1[PC]

12 HDMI2[AV]

13 HDMI2[PC]

14 DisplayPort 16 D-SUB2 17 HDMI3[AV]

18 HDMI3[PC]

1 Normal mode 2 Input signal waiting mode

be selected.

“ERR” when other than RGB is selected for D-SUB1 of INPUT SELECT.

“ERR” when other than COMPONENT is selected for D-SUB1 of INPUT SELECT.

“ERR” when other than VIDEO is selected for D-SUB1 of INPUT SELECT.

“ERR” when PC is selected for HDMI1 of INPUT SELECT.

“ERR” when AV is selected for HDMI1 of INPUT SELECT.

“ERR” when PC is selected for HDMI2 of INPUT SELECT.

“ERR” when AV is selected for HDMI2 of INPUT SELECT.

“ERR” when PC is selected for HDMI3 of INPUT SELECT.

“ERR” when AV is selected for HDMI3 of INPUT SELECT.

3 D-SUB1[COMPONENT] 4 D-SUB1[VIDEO]

9 HDMI1[AV] 10 HDMI1[PC] 12 HDMI2[AV] 13 HDMI2[PC] 14 DisplayPort 16 D-SUB2 17 HDMI3[AV] 18 HDMI3[PC]

○

Page 44

Controlling the Monitor with a PC (RS-232C)

SCREEN menu

AUTO ASNC W 1 When the input mode is D-SUB1[RGB], D-SUB2. CLOCK CLCK WR 0-1200 0-1200 When the input mode is D-SUB1[RGB], D-SUB2.

PHASE PHSE WR 0-63 0-63 When the input mode is D-SUB1[RGB], D-SUB2. POSITIONING POSITION OF

SIZE SIZE OF THE

RESOLUTION

RESET ARST W 1

Function

THE LONGEST DIRECTION

POSITION OF THE SHORTEST DIRECTION

LONGEST DIRECTION

SIZE OF THE SHORTEST DIRECTION

LONGEST DIRECTION RESOLUTION

SHORTEST DIRECTION RESOLUTION

Command Direction

HPOS WR 0-100 0-100 0-800 on D-SUB1[RGB], D-SUB2.

VPOS WR 0-100 0-100 0-200 on D-SUB1[RGB], D-SUB2.

HSIZ WR 0-100 0-100

VSIZ WR 0-100 0-100

HRES WR 300-1920 300-1920 When the input mode is D-SUB1[RGB], D-SUB2.

VRES WR 200-1200 200-1200

Parameter Reply Control/Response contents *

Varies depending on the signal.

Only even numbers are valid for parameters. Varies depending on the signal.

PICTURE menu

Function

BRIGHT VLMP WR 0-31 0-31

CONTRAST CONT WR 0-60 0-60

BLACK LEVEL BLVL WR 0-60 0-60

TINT TINT WR 0-60 0-60

COLORS COLR WR 0-60 0-60

SHARPNESS SHRP WR 0-24 0-24

COLOR ADJUSTMENT

COLOR MODE BMOD WR 0 0 STD

WHITE BALANCE

COPY TO USER CPTU W 0 Copies a preset value to the user setting. GAMMA GAMM WR 0-2 0-2 0: 1.8, 1: 2.2, 2: 2.4 (during PC input)

FLESH TONE (AV input) FLES WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH C.M.S.-HUE (AV input)

C.M.S.-SATURATION (AV input)

C.M.S.-VALUE (AV input)

THRU CTMP WR 0 0 PC input

PRESET 1-28 1-28

USER 99 99

R-CONTRAST CRTR WR 0-256 0-256 “ERR” when CTMP is not set to 99.

G-CONTRAST CRTG WR 0-256 0-256

B-CONTRAST CRTB WR 0-256 0-256

R-OFFSET OFSR WR -127-127 -127-127

G-OFFSET OFSG WR -127-127 -127-127 B-OFFSET OFSB WR -127-127 -127-127

Command Direction

CMHR WR -10-10 -10-10 R

CMHY Y

CMHG G

CMHC C

CMHB B

CMHM M

CRST W 1 Resets the hue.

CMSR WR -10-10 -10-10 R

CMSY Y

CMSG G

CMSC C

CMSB B

CMSM M

CRST W 2 Resets the saturation.

CMVR WR -10-10 -10-10 R

CMVY Y

CMVG G

CMVC C

CMVB B

CMVM M

CRST W 3 Resets the brightness.

Parameter Reply Control/Response contents *

2 2 VIVID

3 3 sRGB (When the input mode is PC)

4 4 HIGH ILLUMINANCE

From 1: approximately 3,000K to 15: approximately 10,000K (500K steps) 16: approximately 5,600K, 17: approximately 9,300K, 18: approximately 3,200K From 19: approximately 10,500K to 28: approximately 15,000K (500K steps)

4-6 4-6 4: USER, 5: 2.0, 6: STD (during PC input)

0: LIGHT 2, 2: DARK (during AV input)

4: USER, 5: LIGHT 1, 6: STD (during AV input)

“ERR” when other than OFF is selected for FLESH TONE.

○

Page 45

Controlling the Monitor with a PC (RS-232C)

Function

ADVANCED AUTO

ANALOG GAIN

ANALOG OFFSET

3D-NR (AV input) TDNR WR 0-2 0-2 0: OFF, 1: LOW, 2: HIGH

MPEG-NR (AV input) MPNR WR 0-1 0-1 0: OFF, 1: ON

3D-Y/C YCSP WR 0-1 0-1 0: OFF, 1: ON (When the input mode is D-SUB1[VIDEO]) RGB INPUT RANGE

(HDMI1[AV])

RGB INPUT RANGE (HDMI1[PC])

RGB INPUT RANGE (HDMI2[AV])

RGB INPUT RANGE (HDMI2[PC])

RGB INPUT RANGE (HDMI3[AV])

RGB INPUT RANGE (HDMI3[PC])

RGB INPUT RANGE (D-SUB1[RGB])

RGB INPUT RANGE (D-SUB2)

RGB INPUT RANGE (DisplayPort)

ACTIVE CONTRAST (AV input)

DISPLAY COLOR PATTERN

DISPLAY COLOR PATTERN (R)

DISPLAY COLOR PATTERN (G)

DISPLAY COLOR

RESET ARST W 2

PATTERN (B)

Command Direction

AGIN W 1 When the input mode is D-SUB1[RGB], D-SUB2.

ANGA WR 0-127 0-127 When the input mode is D-SUB1[RGB], D-SUB2.

ANOF WR 0-127 0-127 When the input mode is D-SUB1[RGB], D-SUB2.

AHDR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

PHDR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

AH2R WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

PH2R WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

AH3R WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

PH3R WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

PDSR WR 1-2 1-2 1: FULL, 2: LIMITED

PD2R WR 1-2 1-2 1: FULL, 2: LIMITED

PDPR WR 0-2 0-2 0: AUTO, 1: FULL, 2: LIMITED

ACNT WR 0-1 0-1 0: OFF, 1: ON

PTDF WR

PTDR WR 0-15 0-15 “ERR” when PTDF is not set to 99.

PTDG WR 0-15 0-15

PTDB WR 0-15 0-15

Parameter Reply Control/Response contents *

0 0 No pattern display.

1 1 White single color pattern display.

2 2 Red single color pattern display.

3 3 Green single color pattern display.

4 4 Blue single color pattern display.

99 99 Red/green/blue mixed color pattern display.

Set each color's level with PTDR, PTDG, PTDB.

○

AUDIO menu

Function

TREBLE AUTR WR -5-5 -5-5

BASS AUBS WR -5-5 -5-5

BALANCE AUBL WR -10-10 -10-10

RESET ARST W 3 -

Command Direction

Parameter Reply Control/Response contents *

○

Page 46

Controlling the Monitor with a PC (RS-232C)

SETUP menu

Function

DATE/TIME SETTING DATE WR DATE DISPLAY FORMAT DTFT WR

TIME DISPLAY FORMAT TMFT WR SCHEDULE SC01-

SCHEDULE BRIGHTNESS SB01-

LANGUAGE LANG WR 14 14 ENGLISH

INPUT SELECT

INPUT MODE NAME

AUDIO SELECT

AUDIO OPTION

TOUCH INPUT SELECT

START INPUT MODE SUIM

COMMUNICATION SETTING

HDMI1 HDSL WR 0-1 0-1 0:PC, 1:AV HDMI2 H2SL WR 0-1 0-1 0:PC, 1:AV HDMI3 H3SL WR 0-1 0-1 0:PC, 1:AV D-SUB1 SLDS WR 0-2 0-2 0:RGB, 1:COMPONENT, 2:VIDEO HDMI1 AUTO VIEW HDMI2 AUTO VIEW HDMI3 AUTO VIEW HOT PLUG CONTROL

(HDMI1) HOT PLUG CONTROL

(HDMI2) HOT PLUG CONTROL

(HDMI3) DisplayPort HDMI1 INH1 HDMI2 INH2 HDMI3 INH3 D-SUB1 IND1 D-SUB2 IND2 DisplayPort HDMI1[PC] HDMI1[AV] HDMI2[PC] HDMI2[AV] HDMI3[PC] HDMI3[AV] D-SUB1[RGB] D-SUB1[COMPONENT] D-SUB1[VIDEO] D-SUB2 SPEAKER SELECT AUDIO OUTPUT AUDIO INPUT LEVEL1 AUDIO INPUT LEVEL2 MONAURAL AUDIO BOTTOM USB

(Long side) SIDE USB (Short side) USCS WR

RS-232C/LAN SELECT

BAUD RATE BAUD WR

Command Direction

SC08

SB08

HDAW WR 0-1 0-1 0: OFF, 1: ON H2AW WR 0-1 0-1 0: OFF, 1: ON H3AW WR 0-1 0-1 0: OFF, 1: ON HPCH WR 0-1 0-1 0: OFF, 1: ON

HPH2 WR 0-1 0-1 0: OFF, 1: ON

HPH3 WR 0-1 0-1 0: OFF, 1: ON

INDP WR 0-30 0-30 0: NO SETTING, 1: PC1, 2:PC2, 3: PC3, 4: TV, 5: VIDEO, 6: DVD, 7: HDD,

ASDI WR 1-3 1-3 ASHP WR 0-2 0-2 ASHA WR 0-2 0-2 AH2P WR 0-2 0-2 AH2A WR 0-2 0-2 AH3P WR 0-2 0-2 AH3A WR 0-2 0-2 ASAP WR 1-2 1-2 ASC2 WR 1-2 1-2 ASV2 WR 1-2 1-2 ASA2 WR 1-2 1-2 SPSL WR 0-1 0-1 AOUT WR 0-2 0-2 AIVP WR 0-1 0-1 AIV2 WR 0-1 0-1 MONO WR 0-1 0-1 USCB WR

CTLS WR

WR ABCDEFFGGH ABCDEFFGGH Schedule of a specied number

WR 0-31 0-31 Screen brightness to change

WR 1-5, 7-8 1-5, 7-8

Parameter Reply Control/Response contents *

AABBCCDDEE AABBCCDDEE

0-2 0-2

0-1 0-1

99 99 Disable brightness setting

1 1 DEUTSCH 2 2 FRANÇAIS 3 3 ITALIANO 4 4 ESPAÑOL 5 5 РУССКИЙ 6 6

0-7 0-7

0-1 0-1

0-2 0-2

AA: Year, BB: Month, CC: Day, DD: Hour, EE: Minute 0: YYYY/MM/DD, 1: MM/DD/YYYY, 2: DD/MM/YYYY

YYYY: Year, MM: Month, DD: Day 0: 24-HOUR TIME, 1: 12-HOUR TIME

A: Schedule 0= Not effective, 1 = Effective B: Power 0 = OFF, 1 = ON C: Day of the week 1 0 = Only once, 1 = Every week, 2 = Every day D: Day of the week 2* 0 = Sunday, 1 = Monday through 6 = Saturday, 9 = Not exist E: Day of the week 3* 0 = Sunday, 1 = Monday through 6 = Saturday, 9 = Not exist F: Hour 00-23 G: Minute 00-59 H: Input 0 = Not specied, 1 = HDMI1, 2 = HDMI2, 3 = HDMI3,

* If “Every day” is selected for “Day of the week 1”, “ERR” occurs when other

than 9 is selected.

“ERR” when LOW POWER is selected for STANDBY MODE.

8: DVR, 9: BD, 10: CAMERA, 11: DOCUMENT CAMERA, 12: VIDEO CAMERA, 13: VIDEO CONFERENCE, 14: WIRELESS, 15: STB, 16: CONTROLLER, 17: COMPOSITE, 18: COMPONENT, 19: RGB, 20: INPUT1, 21: INPUT2, 22: INPUT3, 23: INPUT4, 24: INPUT5, 25: INPUT6, 26: SATELLITE, 27: CABLE, 28: CAMCORDER, 29: TABLET, 30: SURVEILLANCE CAM.

1: AUDIO1, 2: AUDIO2, 3: DisplayPort 0: HDMI, 1: AUDIO1, 2: AUDIO2 0: HDMI, 1: AUDIO1, 2: AUDIO2 0: HDMI, 1: AUDIO1, 2: AUDIO2 0: HDMI, 1: AUDIO1, 2: AUDIO2 0: HDMI, 1: AUDIO1, 2: AUDIO2 0: HDMI, 1: AUDIO1, 2: AUDIO2 1: AUDIO1, 2: AUDIO2 1: AUDIO1, 2: AUDIO2 1: AUDIO1, 2: AUDIO2 1: AUDIO1, 2: AUDIO2 0: Internal speaker, 1: External speaker 0: VARIABLE1, 1: FIXED, 2: VARIABLE2 0: 1.0Vrms, 1: 0.5Vrms 0: 1.0Vrms, 1: 0.5Vrms 0: OFF, 1: ON 0: INVALID, 1: BOTTOM INPUT TERM. (Long side), 2: DisplayPort, 3: HDMI1,

4: HDMI2, 5: HDMI3, 6: D-SUB1, 7: D-SUB2 0: INVALID, 1: SIDE INPUT TERM. (Short side), 2: DisplayPort, 3: HDMI1,

4: HDMI2, 5: HDMI3, 6: D-SUB1, 7: D-SUB2 1: LAST INPUT MODE, 2: DisplayPort, 3: HDMI1, 4: HDMI2, 5: HDMI3,

7: D-SUB1, 8: D-SUB2 0: RS-232C 1: LAN

0: 9600bps, 1: 19200bps, 2: 38400bps

4 = D-SUB1, 5 = D-SUB2, 6 = DisplayPort

○

Page 47

Controlling the Monitor with a PC (RS-232C)

MONITOR menu

MONITOR STDR WR 0-1 0-1 0: LANDSCAPE, 1: PORTRAIT OSD H-POSITION OSDH WR 0-100 0-100 OSD V-POSITION OSDV WR 0-100 0-100 OPERATION MODE FNCM WR 0-1 0-1 0: MODE1, 1: MODE2 STANDBY MODE STBM WR 0-1 0-1 0: STANDARD, 1: LOW POWER

OFF IF NO OPERATION ATOF WR 0-1 0-1 0: OFF, 1: ON POWER ON

DELAY

SELF ADJUST SELF ADJUST AADJ WR 0-1 0-1 0: OFF, 1: ON

TOUCH OUTPUT INVALID DISP.

TOUCH OPERATION MODE TOMD WR 0-2 0-2 0: AUTO, 1: MULTI-TOUCH MODE, 2: MOUSE MODE

TOUCH PANEL MODE GMDP WR 0-1 0-1 0: OFF, 1: ON (When the input mode is PC)

Function

POWER ON DELAY INTERVAL PWOD WR 0-60 0-60 0: OFF, 1-60 seconds

START TIMING AADD WR 10-200 10-200 10: 1 second through 200: 20 seconds TOUCH OUTPUT

INVALID ICON CHANGE DISPLAY

POSITION

Command Direction

PODS WR 0-1 0-1 0: OFF, 1: ON

TOPI WR 0-1 0-1 0: OFF, 1: ON

TOIP WR 0-3 0-3 0: UPPER RIGHT, 1: UPPER LEFT, 2: LOWER RIGHT, 3: LOWER LEFT

Parameter Reply Control/Response contents *

When ADJUSTMENT LOCK is set to ON2, LOW POWER cannot be selected (ERR). “ERR" when SCHEDULE is effective.

“ERR” when the touch panel is not connected. “ERR” when Touch Panel Settings Tool is installed in the computer connected to the touch panel.

PIP/PbyP menu

PIP MODES MWIN WR 0-3 0-3 0: OFF, 1: PIP, 2: PbyP, 3: PbyP2 PIP SIZE MPSZ WR 1-64 1-64 PIP POS THE LONGEST

PIP POS LD+SD BATCH MPOS W 0-100,0-100 Specify the position in MPOSxxxyyy format.

PIP BLEND MWBL WR 0-15 0-15 PIP SOURCE MWIP WR 2 2 D-SUB1[RGB]

SOUND CHANGE MWAD WR 1-2 1-2 1: MAIN, 2: SUB MAIN POS (Main screen) MWPP WR 0-1 0-1 0: POS1, 1: POS2 PbyP2 POS (Sub screen) MW2P WR 0-2 0-2 0: POS1, 1: POS2, 2: POS3 AUTO OFF MOFF WR 0-1 0-1 0: MANUAL, 1: AUTO

Function

DIRECTION THE SHORTEST

DIRECTION

Command Direction

MHPS WR 0-100 0-100

MVPS WR 0-100 0-100

R 0-100,0-100 Returns a response in (xxx,yyy) format.

Parameter Reply Control/Response contents *

3 3 D-SUB1[COMPONENT] 4 4 D-SUB1[VIDEO]

9 9 HDMI1[AV] 10 10 HDMI1[PC] 12 12 HDMI2[AV] 13 13 HDMI2[PC] 14 14 DisplayPort 16 16 D-SUB2 17 17 HDMI3[AV] 18 18 HDMI3[PC]

(xxx: Longer side, yyy: Shorter side position)

○

Page 48

Controlling the Monitor with a PC (RS-232C)

OTHERS menu

SCREEN MOTION PATTERN SCSV WR 0-4 0-4 0: OFF, 1-4: PATTERN1-4

POWER MANAGEMENT (PC) PMNG WR 0-1 0-1 0: OFF, 1: ON POWER MANAGEMENT (AV) PMAV WR 0-1 0-1 0: OFF, 1: ON CONNECT AUTO INPUT SELECT AICO WR 0-1 0-1 0: OFF, 1: ON NO SIGNAL AUTO INPUT SEL. AINO WR 0-1 0-1 0: OFF, 1: ON AUTO INPUT

SELECT PRIORITY

LOGO SCREEN BTSC WR 0-1 0-1 0: OFF, 1: ON INPUT

RESOLUTION (PC)

INPUT RESOLUTION (AV) ZOOM2 SPECIAL SETTING

(D-SUB1[RGB], D-SUB2) SCAN MODE SCAN WR 0-2 0-2 0: MODE1, 1: MODE2, 2: MODE3 (When the input mode is AV) COLOR SYSTEM CSYS WR 0-5 0-5 0: AUTO, 1: PAL, 2: PAL-60, 3: SECAM, 4: NTSC3.58, 5: NTSC4.43

Function

MOTION TIME1 MTIM WR 0-20 0-20 MOTION TIME2

(PATTERN1) MOTION TIME2

(PATTERN2-4)

DisplayPort HDMI1 APH1 HDMI2 APH2 HDMI3 APH3 D-SUB1 APD1 D-SUB2 APD2

RESOLUTION CHECK PIXEL SETTING

(D-SUB1[RGB], D-SUB2)

RESOLUTION CHECK

Command Direction

MINT WR 10-990 10-990 Per 10 seconds

MINT WR 5-20 5-20 Per second

APDP WR 0-6 0-6 0: Not selected by auto input selection, 1-6: Priority setting

PXCK R - Returns current resolution in the form of hhh, vvv. PXSL WR 1 1 768) 1360 x 768

RESO R - 480i, 480p, 1080i, 720p, 1080p , etc.

Z2SP WR 0-1 0-1 0: OFF, 1: ON

Parameter Reply Control/Response contents *

• “ERR” when OFF is selected for NO SIGNAL AUTO INPUT SEL..

• All input terminals cannot be set to 0 simultaneously.

2 2 768) 1280 x 768

3 3 768) 1024 x 768

5 5 480) 848 x 480

6 6 480) 640 x 480

7 7 1050) 1680 x 1050

8 8 1050) 1400 x 1050

9 9 768) AUTO 10 10 480) AUTO

○

Page 49

Controlling the Monitor with a PC (RS-232C)

Initialization/Functional Restriction Setting (FUNCTION) menu

ALL RESET RSET W 0-1 0: ALL RESET 1, 1: ALL RESET 2 -

Function

ADJUSTMENT LOCK ALCK WR 0-2 0-2 0: OFF, 1:ON1, 2:ON2

ADJUSTMENT LOCK TARGET ALTG WR 0-2 0-2 0: REMOTE CONTROL, 1: MONITOR BUTTONS, 2: BOTH

OSD DISPLAY LOSD WR 0-2 0-2 0: ON1, 1: OFF, 2: ON2 LED OFLD WR 0-1 0-1 0: ON, 1: OFF TEMPERATURE ALERT TA LT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED STATUS ALERT SALT WR 0-2 0-2 0: OFF, 1: OSD & LED, 2: LED POWER BUTTON PBTN WR 0-1 0-1 0: MONITOR, 1: EXT. CONTROLLER EXTERNAL CONTROLLER INPUT PCIP WR 0-5 0-5 0: D-SUB1, 1: D-SUB2, 2: DisplayPort, 3: HDMI1, 4: HDMI2, 5: HDMI3

Command Direction

Parameter Reply Control/Response contents *

When STANDBY MODE is set to LOW POWER, ON2 cannot be selected (ERR).

“ERR” when OFF is selected for ADJUSTMENT LOCK.

“ERR” when MONITOR is selected for POWER BUTTON.

Others

Function

SCREEN SIZE (PC) WIDE WR 0-5 0-5 SCREEN SIZE (AV) WIDE WR 0-5 0-5 VOLUME VOLM WR 0-31 0-31 MUTE MUTE WR 0-1 0-1 0: OFF, 1: ON INFORMATION MODEL INF1 R Value

SERIAL NO SRNO R Value

TEMPERATURE SENSOR DSTA R 0 Internal temperature normal

TEMPERATURE ACQUISITION ERRT R Value Returns the temperature at the temperature sensors.

CAUSE OF LAST STANDBY MODE STCA W 0 Initialization

Touch operation valid/invalid TPEN WR 0-1 0-1 0: Invalid, 1: Valid

Command Direction

R 0 No detectable error has occurred

Parameter Reply Control/Response contents *

0: Toggle to change size, 1: WIDE, 2: NORMAL, 3: Dot by Dot, 4: ZOOM1, 5: ZOOM2 0: Toggle to change size, 1: WIDE, 2: ZOOM1, 3: ZOOM2, 4: NORMAL, 5: Dot by Dot

1 Internal temperature abnormal has occurred and the monitor is in standby mode 2 Internal temperature abnormal occurred (To delete the information of temperature

abnormal, turn off the main power.) 3 Internal temperature abnormal has occurred and backlight brightness is dimmed 4 Temperature sensor abnormal

Indicates a temperature sensor abnormality when “126” is returned.

1 Standby mode by POWER button 2 Main power off by the main power switch 3 Standby mode by RS-232C or LAN 4 Input signal waiting mode by No Signal 6 Standby mode by abnormal temperature 8 Standby mode by SCHEDULE setting

20 Standby mode by OFF IF NO OPERATION setting

“ERR” when TOUCH INPUT SELECT is set to INVALID or the touch panel is not

connected.

○

Page 50

Controlling the Monitor with a PC (RS-232C)

Commands for setting of the GAMMA user data

Function

RED GAMMA DATA TRANSFER UGRW W aaxxxx GREEN GAMMA DATA TRANSFER UGGW W BLUE GAMMA DATA TRANSFER UGBW W

RED GAMMA DATA READ UGRR W 1-16 xxxx GREEN GAMMA DATA READ UGGR W 1-16 BLUE GAMMA DATA READ UGBR W 1-16 USER DATA INITIALIZE UGRS W 0 Initialize the user data. USER DATA SAVE UGSV W 0 Save the user data in the monitor.

Command Direction

Parameter Reply Control/Response contents *

xxxxcc

··· (xxxx: 32 pieces) aa: 01-16 xxxx: 0000-1023 cc: 00-FF

xxxx

··· (xxxx: 32 pieces) xxxx: 0000-1023

aa: Block number xxxx: 32 pieces of user data cc: Checksum (ASCII data) of the block number and user data

xxxx: User data of 32 pieces

○

Page 51

Controlling the Monitor with a PC (LAN)

ENTER

Your monitor can be connected to a LAN allowing you to control it from a PC on the LAN.

You can also congure the monitor to send e-mail notication

when it has a problem. The connection requires a commercially available LAN cable (UTP cable, Category 5, straight through).

Network (LAN)

LAN terminal

Hub

LAN cable (commercially available, straight)

TIPS

• You must assign an IP address to the monitor by following

the procedures in “Settings to connect to a LAN”. (See the description on the right.)

• Your PC must be installed with Internet Explorer (version 7.0

or later).

- Version 7, 8, 9, 10 or 11 of Internet Explorer is recommended.

• When STANDBY MODE is set to LOW POWER, control is

not possible in standby mode.

• To control the monitor via LAN, set RS-232C/LAN SELECT

to LAN. (See page 32.)

• You cannot use RS-232C and LAN control simultaneously.

Initializing personal information

• Personal information such as e-mail addresses can be

registered in the monitor. Before transferring or disposing of the monitor, initialize all settings by selecting ALL RESET

1. (See page 39.) Note that ALL RESET 2 will not initialize e-mail addresses and other settings.

Settings to connect to a LAN

Set the monitor’s IP address and subnet mask to match the settings of your LAN. These settings can be made on either the monitor or a PC connected to the monitor.

The settings depend on the conguration of your LAN. Ask

your LAN administrator for details.

To set on the monitor

Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN, and then set the LAN SETUP options. (See page 32.)

After setting each item, select SET and press

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address. Press

change the values.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask. Press

change the values.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a gateway, specify “0.0.0.0”.

Press change the values.

RESET

Resets the values of the LAN settings to the factory preset values.

Select ON and then press

or to select items, and press or to

ENTER

Page 52

Controlling the Monitor with a PC (LAN)

To set from a PC

When the monitor is connected to a PC, LAN settings can be

congured via PC.

Set up process

(1) Connect your monitor to a PC (2) Specify the PC’s IP address

(3) Congure the monitor’s LAN settings

(1) Connecting your monitor to a PC

Connect a commercially available crossover LAN cable (UPT cable, Category 5) to the LAN port on the PC and this monitor.

LAN terminal

To LAN terminal

7. Temporarily change the IP address and subnet mask. To access the monitor as it is shipped from the factory, set as follows.

• IP Address: 192.168.150.1

• Subnet Mask: 255.255.255.0

• Default Gateway: (leave blank)

8. Click [OK] and then reboot the PC.

TIPS

• This monitor is factory preset as shown below.

(When DHCP CLIENT is set to OFF)

IP Address : 192.168.150.2 Subnet Mask : 255.255.255.0 Default Gateway : 0.0.0.0

LAN cable

(commercially available, crossover)

(2) Specifying the PC’s IP address

To congure the monitor’s LAN settings, you must temporarily

change the settings on the PC. This explanation is based on Windows 7.

1. Log on to the PC with an administrator account.

2. Click [Start], and then click “Control Panel”.

3. Click “View network status and tasks” in “Network and Internet”. In “Classic View”, click “Network and Sharing Center”.

4. Click “Local Area Connection” and then “Properties”.

5. Click “Internet Protocol Version 4 (TCP/IPv4)” and then “Properties”.

6. Make a note of the current IP address, subnet mask, and default gateway settings. Make sure you write this information now as you will be changing the IP address, subnet mask, and default gateway settings back to these settings afterwards.

(3) Conguring the monitor’s LAN settings

Access the monitor using Internet Explorer.

Controlling the monitor

1. Turn the power ON to the monitor.

2. Set RS-232C/LAN SELECT of COMMUNICATION SETTING on the SETUP menu to LAN.

3. Set DHCP CLIENT of LAN SETUP of COMMUNICATION SETTING on the SETUP menu to OFF.

PC operation

4. Launch Internet Explorer, in the “Address” box type “http://192.168.150.2/” and press the Enter key.

Page 53

DISPLAY

Controlling the Monitor with a PC (LAN)

5. Click on “LAN SETUP” under NETWORK.

6. Specify the “DHCP CLIENT”, “IP ADDRESS”,etc.

Controlling with a PC

TIPS

• For security, set a USER NAME and PASSWORD. (See

page 55.)

Basic operation

You use Internet Explorer on a PC on the LAN to control the monitor.

1. Launch Internet Explorer on the PC.

In the “Address” box, type “http://” followed by your monitor’s IP address followed by “/”, then press the Enter key.

You can conrm the IP address with the DISPLAY function.

When prompted to enter a user name and password, type

the user name and password that you specied in the

security settings (see page 55.), and click [OK].

3. You can check, control, and change the monitor’s status and settings by clicking the menu items on the left side of the screen.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

7. When the setting is changed, click [Apply].

8. Check the message and click [OK].

9. Exit Internet Explorer. 10

. Restore the PC’s IP address jotted in Step 6, “(2)

Specifying the PC’s IP address”.

11.

Connect the monitor and the PC to the LAN.

TIPS

• Wait 10 seconds after clicking [OK] before proceeding.

• When operating using the remote control unit or similar,

click [Refresh].

• If you see an [Apply] button next to a setting, click it after

you change that setting.

TIPS

• See pages 54 to 58 for details on each setting.

• If you click [Refresh] before the screen nishes updating

the current display, the “Server Busy Error” will appear. Wait for a moment before operating your monitor again.

• You cannot operate the monitor while it is warming up.

• If DHCP CLIENT is set to ON, press

control unit two times and then check the monitor’s IP address.

on the remote

Page 54

POWER INPUT SIZE

Controlling the Monitor with a PC (LAN)

INFORMATION

Information about this monitor appears.

CONTROL

You can control the operations corresponding to the buttons (

) on the remote control unit. (See page 25.)

ADJUSTMENT

You can adjust these settings which are also available on the monitor’s menu.

• SCREEN (See page 28.)

• PICTURE (See pages 29 to 30.)

• AUDIO (See page 31.)

• SETUP (See pages 31 to 32.)

• MONITOR (See page 33.)

• SCHEDULE (See page 37.)

• PIP/PbyP (See page 34.)

• OTHERS (See page 35.)

• FUNCTION (See page 39.)

TIPS

• In standby mode, Power ON is the operation available.

TIPS

• After changing DISPLAY COLOR PATTERN to OFF in

PICTURE menu, click [Refresh] to correctly retrieve the status of the monitor.

Page 55

Controlling the Monitor with a PC (LAN)

NETWORK (LAN SETUP)

This screen allows you to set the settings necessary when the monitor is connected to a LAN.

DHCP CLIENT

If your LAN has a DHCP server and you wish to obtain an address automatically, change this setting to ON. To set the address manually, set this to OFF.

IP ADDRESS

If the DHCP CLIENT is set to OFF, specify an IP address.

SUBNET MASK

If the DHCP CLIENT is set to OFF, specify the subnet mask.

DEFAULT GATEWAY

If the DHCP CLIENT is set to OFF, specify the default gateway. If you are not using a default gateway, specify “0.0.0.0”.

DNS SERVER ADDRESS AUTO ACQUISITION

If the DHCP CLIENT is set to ON, specify whether or not to automatically obtain the DNS server address.

DNS SERVER

Specify the DNS server address if the DHCP CLIENT is set to OFF or the DNS SERVER ADDRESS AUTO ACQUISITION is set to OFF. If you are not using a DNS server, specify “0.0.0.0”.

RESET

Clicking [Execute] returns all of the LAN SETUP settings to the factory-preset values except for the DNS SERVER ADDRESS AUTO ACQUISITION and DNS SERVER settings.

NETWORK (SECURITY)

This screen allows you to specify the security-related settings.

USER NAME / PASSWORD

Sets up a user name and password to restrict access to this monitor. After entering a user name and password, click [Apply].

ACCEPT IP ADDRESS

You can limit access to this monitor by registering IP addresses of PCs that should have access.

To limit access, specify the option “From only specic IP

addresses”. Otherwise, to allow access from any PC, specify “All IP Addresses”.

IP ADDRESS 1 to 3

If “ACCEPT IP ADDRESS” is set to “From only specic IP

addresses”, enter the IP addresses that you want to allow.

TIPS

• The USER NAME and PASSWORD can be up to 8

alphanumeric characters (hyphens and underscores allowed).

• To cancel the user name and/or password after it has been

set, make the box empty and click [Apply].

Page 56

Controlling the Monitor with a PC (LAN)

NETWORK (GENERAL)

This screen allows you to specify the general LAN settings.

MONITOR NAME

Specify a name for this monitor as it should appear on the Internet Explorer screen.

AUTO LOGOUT TIME

Specify the time (in minutes) to elapse before automatically disconnecting this monitor from the network. Specify in minutes from 1 to 65535. A value of ‘0’ will disable this function.

DATA PORT

Specify the TCP port number to use for exchanging data with the monitor. Specify a value from 1025 to 65535.

SEARCH PORT

Specify the port number to use when searching for this monitor. Specify a value from 1025 to 65535.

INSTALLATION INFORMATION (NAME/LOCATION)

Specify the information to display for this monitor in the Internet Explorer window.

LINK MODE

Selects the link speed and duplex. Use AUTO normally.

TIPS

• The MONITOR NAME can be up to 16 alphanumeric

characters or symbols.

• Enter up to 50 characters in the NAME eld in the

INSTALLATION INFORMATION.

• Enter up to 100 characters in the LOCATION eld in the

INSTALLATION INFORMATION.

MAIL (ORIGINATOR)

This screen allows you to congure the e-mail sent periodically

or when the monitor has an error.

The settings depend on the conguration of your LAN. Ask

your LAN administrator for details.

SMTP SERVER

Specify the SMTP server address for sending e-mail.

* When using a domain name, make sure to specify the

DNS SERVER as well. (See page 55.)

SMTP PORT

If the “AUTHENTICATION” is “SMTP-AUTH”, specify the port number.

ORIGINATOR E-MAIL ADDRESS

Specify the e-mail address for this monitor. This address becomes the e-mail address of the originator.

ORIGINATOR NAME

Specify the name for the originator.

This name appears in the “Originator Name” eld of the

e-mail.

AUTHENTICATION

Specify the authentication method to use when sending e-mail.

POP SERVER

If the “AUTHENTICATION” method is “POP before SMTP”, specify the POP server address.

ACCOUNT NAME / PASSWORD

If the “AUTHENTICATION” is “POP before SMTP” or “SMTP-AUTH”, specify the account name and password to connect to the SMTP server.

TIPS

• You can enter up to 64 alphanumeric characters or symbols

for the ORIGINATOR E-MAIL ADDRESS, ORIGINATOR NAME, ACCOUNT NAME, and PASSWORD.

• The SMTP SERVER and POP SERVER can be up to 64

characters.

The following characters can be used: a-z, A-Z, 0-9, - , .

Page 57

Controlling the Monitor with a PC (LAN)

MAIL (RECIPIENT)

This screen allows you to specify the recipients of the e-mail sent periodically or when the monitor has an error.

RECIPIENT E-MAIL ADDRESSES

Specify the e-mail addresses to send error notication e-mail

to.

CONDITION

Specify the conditions to send mails. When you check PERIODICAL, specify the date and time to send the mails in the PERIODICAL setting.

CONFIRMATION

Sends test e-mail.

This allows you to conrm that the e-mail settings are congured properly.

Attach the log le to a TEMPERATURE/HARDWARE error

e-mail.

When this option is checked, a log is added to the mail which

noties a temperature or status error.

E-MAIL TRANSMISSION ERROR REPORT

A report of the latest e-mail transmission errors will be displayed. The error report will be displayed when an e-mail transmission error occurs. Also, the e-mail transmission errors will be cleared when ALL RESET1 is executed. (See page 39.)

MAIL (PERIODICAL)

When PERIODICAL for CONDITION of MAIL (RECIPIENT) is checked, set the date and time to send the mail.

DAY OF THE WEEK

Specify the day of the week to send the periodical mails.

TIME

Specify the time of the day to send the periodical mails.

Caution

• Do not turn off the main power when you set to send the

periodical mails.

• Specify the correct date and time. (See page 31.)

If the date and time settings are incorrect, the periodical mail is not sent properly.

• Regularly conrm that the specied date and time is

correct.

• When LOW POWER is selected for STANDBY MODE,

periodical mails will not be sent in standby mode.

TIPS

• The RECIPIENT E-MAIL ADDRESSES can be up to 64

alphanumeric characters or symbols.

Page 58

Controlling the Monitor with a PC (LAN)

SNMP

You can congure settings related to SNMP.

TIPS

• Depending on the SNMP settings, a short delay may occur

before the SNMP is usable. (About 5 minutes)

• Up to 16 alphanumeric letters and symbols can be used for

the community name, user name and password.

SERVICE & SUPPORT

(URL INFORMATION)

You can display a specic URL in the URL INFORMATION eld on the INFORMATION screen when an error occurs in

the monitor. (See page 54.)

SNMP SETTING

Set whether to enable or disable SNMP.

VERSION

Set the version of the SNMP to be supported.

COMMUNITY NAME 1 to 3

Set the name of the community required for the access.

USER 1 to 3

Set the user name, password, authentication method and other options required for access.

TRAP SETTING

Set whether to enable or disable the trap function. When this function is enabled, a trap will be sent when the monitor is turned on. A test transmission of a trap can be performed in “Test”.

TRAP SETTING OF AUTHENTICATION ERROR

Set whether the trap function sends a notication when

authentication fails.

TRAP ADDRESS & PORT

Set the destination address and port number of the

notication sent by the trap function.

Caution

• After you set SNMP, click [Switch the main power of

monitor off and on now.] or turn off the monitor and then turn it on again with the main power switch. When the monitor restarts, wait about 30 seconds and then start the next operation.

• If the IP address is changed while the SNMP function is

operational, turn off the monitor and then turn it on again with the main power switch.

URL INFORMATION

Enter the URL to display on the INFORMATION screen when an error occurs on the monitor. Up to 64 alphanumeric characters or symbols can be used.

CONDITION

Specify the condition to display the URL.

CONFIRMATION

The home page of the specied URL is displayed.

You can check whether the URL you entered is correct.

TIPS

• It is also possible to specify the message text, such as the

name of a contact or a telephone number, to be displayed instead of the linked URL.

Page 59

[Advanced operation] Command-based control

You can control the monitor using RS-232C commands (see page 43) via terminal software and other appropriate applications. In order to use this function, enable a connection to the monitor through Internet Explorer. Read the manual for the terminal software for detailed instructions.

(1) Connect the PC to the monitor.

1. Specify the IP address and data port number and connect the PC to the monitor. When connection has been established successfully, [

2. Send the user name set in the SECURITY settings (see page 55).

• Send [User name] + [

• If the user name is not set, send [

• When the transmission is successful, [

is returned as response.

3. Send the password set in the SECURITY settings (see page 55).

• Send [Password] + [

• If the password is not set, send [

• When the transmission is successful, [OK

returned as response.

(2) Send commands to control the monitor.

• The commands used are the same as those for RS-

232C. Refer to the communication procedure (see page 40) for operation.

• Usable commands are provided in the RS-232C

command table (see page 43).

(3) Disconnect the connection with the monitor and

quit the function.

1. Send [BYE ]. When the transmission is successful, [goodbye] is returned and the connection is disconnected.

Password:]

] is

Controlling the Monitor with a PC (LAN)

TIPS

• Connection is automatically disconnected when the time specied in AUTO LOGOUT TIME elapses over a

no-communication period.

Page 60

Troubleshooting

If you are experiencing any problem with your display, before calling for service, please review the following troubleshooting tips.

There is no picture or sound.

• Is the power cord disconnected? (See page 14.)

• Is the main power switch off? (See page 17.)

• Is the monitor in standby mode (the power LED illuminating

in orange)? (See page 17.)

• Make sure correct input mode is selected. (See pages 24

to 25.)

• If any external equipment is connected, make sure the

equipment is operating (playing back).

Remote control does not work.

• Are the batteries inserted with polarity (+,-) aligned? (See

page 15.)

• Are the batteries exhausted?

• Point the remote control unit toward the monitor’s remote

control sensor. (See page 15.)

• Is the menu display hidden or is operation disabled? (See

page 39.)

Sound from left and right speakers is reversed. Sound is heard from only one side.

• Are audio cables connected properly? (See page 13.)

• Make sure audio cables for external speakers are

connected properly: left and right cables may be reversed or one of the two cables may not be connected. (See page

13.)

• Check the setting of BALANCE for AUDIO menu. (See

page 31.)

There is a picture but no sound.

• Is the sound muted?

• Make sure the volume is not set to minimum.

• Are audio cables connected properly?

• Is the setting of AUDIO SELECT on the SETUP menu

correct? (See page 31.)

• Is the setting for SPEAKER SELECT of AUDIO OPTION on

the SETUP menu correct? (See page 31.)

Unstable video.

• The signal may be incompatible.

• Try the automatic screen adjustment when D-SUB1[RGB]

or D-SUB2 are used.

• If the top and bottom of the image are not horizontally

aligned, set TOUCH PANEL MODE on the MONITOR menu to OFF.

The video from the HDMI input terminal does not appear properly.

• Is the setting for HDMI1/HDMI2/HDMI3 of INPUT SELECT

on the SETUP menu correct? (See page 31.)

• Is the HDMI cable HDMI standard compliant? The monitor

will not work with cables that are not standard compliant.

• Is the input signal compatible with this monitor? (See pages

64 to 65.)

The video from D-sub1 input terminal does not appear correctly.

• Is the setting for D-SUB1 of INPUT SELECT on the SETUP

menu correct? (See page 31.)

• Is the input signal compatible with this monitor? (See page

64.)

The video from D-sub2 input terminal does not appear correctly.

• Is the input signal compatible with this monitor? (See page

64.)

The video from DisplayPort input terminal does not appear correctly.

• Is the input signal compatible with this monitor? (See page

64.)

• Is the DisplayPort cable DisplayPort standard compliant?

The monitor will not work with cables that are not standard compliant.

Control buttons do not work. There is no picture.

• Load noises from outside may be interfering with normal

operation. Turn off the power and turn it on after waiting at least 5 seconds, and then check the operation.

The input mode changes automatically.

• When CONNECT AUTO INPUT SELECT is ON, the input

mode automatically changes to that terminal when a video signal is input into the input terminal. For this reason, the input mode may change when the computer wakes up from system standby.

• When the NO SIGNAL AUTO INPUT SEL. is ON and no

signal is present in a selected input mode, the monitor automatically changes the selected mode to a mode where a video signal is present.

The input mode may change in the following cases:

- When a computer is in standby mode.

- When video play is stopped with a playback device.

The touch panel does not respond.

• Is the USB cable connected properly? (Touch Panel

Settings Tool Operation Manual)

• Have Touch Panel Settings Tool and Touch Pen Utility been

installed? (Touch Panel Settings Tool Operation Manual, Touch Pen Utility Operation Manual)

• Has the pen tip of the touch pen become worn? Replace

the pen tip. (See page 20.)

• Is the battery inserted in the wrong orientation (+, -) in the

touch pen? (See page 19.)

• Is the touch pen battery exhausted?

• Are touch pens that are supplied touch pens or optional

PN-ZL03 used? “CAPACITIVE” is indicated on touch pens that can be used with this monitor.

CAPACITIVE

• If your nger is too dry, the screen may not respond.

• Do not touch the screen when the monitor power is turned

on, it will lead to a malfunction. When this occurs, turn the monitor power off and then on.

Page 61

Power LED ashes red.

“STATUS [xxxx]” appears in the corner of the screen.

• Hardware has a problem. Turn off the monitor and request

repair from your SHARP dealer. (When STATUS ALERT is set to OSD & LED. This varies depending on the setting.)

When “AUTO DIMMING” is displayed.

• When the internal temperature of the monitor rises

excessively, the brightness of the backlight automatically decreases in order to prevent a further temperature rise. If

you attempt to use the monitor is in this state, “AUTO DIMMING” is displayed and you cannot change the brightness.

• Remove the cause of the excessive temperature rise.

The monitor makes a cracking sound.

• You may occasionally hear a cracking sound from the

monitor. This happens when the cabinet slightly expands and contracts according to change in temperature. This does not affect the monitor’s performance.

The Power LED is ashing in red and green alternately. When “TEMPERATURE” is displayed in the corner of the screen.

• When the internal temperature of the monitor rises

excessively, the brightness of the backlight decreases automatically in order to prevent high-temperaturerelated problems. When this occurs, “TEMPERATURE” is

displayed on the screen and the Power LED ashes red

and green alternately. (When TEMPERATURE ALERT is set to OSD & LED. This varies depending on the setting.)

• If the internal temperature rises further, the monitor

automatically enters standby mode. (The Power LED

continues ashing red and green alternately.)

• Remove the cause of the excessive temperature rise.

- If the monitor enters standby mode due to a rise in

temperature, to return to normal display, turn the power switch off and then back on again. The monitor, however, will enter standby mode again if the cause of the temperature rise is not eliminated. (See page 7.)

- Check whether the monitor is placed at a location where

a quick rise in temperature is likely. Internal temperature rises quickly if the vents on the monitor are blocked.

- Internal temperature rises quickly if dust accumulates

inside the monitor or around the vents. Remove dust if possible. Ask SHARP dealer about removing internal dust.

to adjust the brightness while

Troubleshooting

Page 62

Specications

Product Specications

Model PN-80TC3 LCD component Max. resolution (pixels) Max. colors Pixel pitch Viewing angle Screen active area inch (mm) Computer input signal Sync signal

Video color system Plug and play Power management Input terminals

PC/AV HDMI x 3 PC Mini D-sub 15 pin, 3 rows x 2

Audio Serial (RS-232C)

Output terminals

Video/Audio Audio

LAN terminal 10 BASE-T/100 BASE-TX Speaker output (internal/external) 10 W + 10 W/10 W + 10 W

Touch Panel

Detection method Capacitive type PC connector USB (2.0 compliant) (Type B) x 2

Touch pen Wireless communication method

Touch pen adapter port

Power requirement AC 100 V - 240 V, 3.2 A, 50/60 Hz

Operating temperature Operating humidity

*2*

Power consumption

(Maximum / input signal waiting mode

standby mode

Dimensions (excluding protrusions) inch (mm) Weight lbs. (kg)

*1 D-sub input terminal only. *2 Temperature condition may change when using the monitor together with the optional equipments recommended by SHARP.

In such cases, please check the temperature condition specied by the optional equipments.

*3 In addition, check the requirements of the computer and other devices to be connected, and make sure that all requirements are satised.

*4 When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF. *5 When STANDBY MODE is set to STANDARD. When STANDBY MODE is set to LOW POWER: 0.5 W

As a part of our policy of continuous improvement, SHARP reserves the right to make design and specication changes for product improvement without prior notice. The performance specication gures indicated are nominal values of production units. There may be some deviations from

these values in individual units.

)

80" Class [80 inch (203.2cm) diagonal] TFT LCD 1920 x 1080 Approx. 1.06 billion colors

0.923 mm (H) × 0.923 mm (V)

176° right/left/up/down (contrast ratio ≥ 10)

69-3/4 (W) x 39-1/4 (H) (1771.2 x 996.3)

Analog RGB (0.7 Vp-p) [75 Ω], DisplayPort 1.1a

Horizontal/vertical separate (TTL: positive/negative), Sync-on-green*1, Composite sync (TTL: positive/negative)

NTSC (3.58MHz)/NTSC (4.43MHz)/PAL/PAL-60/SECAM VESA DDC2B VESA DPMS

DisplayPort x 1

3.5 mm mini stereo jack x 2

3.5 mm mini jack x 1 DisplayPort x 1

3.5 mm mini stereo jack x 1

6 Ω

(2.4 GHz, IEEE 802.15.4 compliant, DS-SS method) USB (2.0 compliant) (Type A)

41°F to 95°F (5°C to 35°C) 20% to 80% (no condensation) 280 W / 6.0 W / 3.5 W

Approx. 72-13/16 (W) x 3-3/4 (D) x 42-3/16 (H) (1850 x 96 x 1072) Approx. 169.8 (77)

Page 63

Dimensional Drawings

Unit: inch [mm]

Note that the values shown are approximate values.

Specications

3-3/4

[96]

6-5/16 [161]

2-9/16

[65]

3-1/8

[80]

45-7/16 [1154]

43-9/16 [1106]

42-3/16 [1072]

72-13/16 [1850]

Opening width (70-9/16 [1792])

33-1/4 [844]

55-7/16 [1408]

1-3/8

[35]

)

Opening height

39-13/16 [1012]

(

VESA holes *

11-13/16

[300]

11-13/16

[300]

7-7/8

[200]

When mounting the monitor, be sure to use a wall-mount bracket that complies with the VESA-compatible mounting method. SHARP recommends using M6 screws and tighten the screws. Note that screw hole depth of the monitor is 3/8 inch (10 mm). Loose mounting may cause the product to fall, resulting in serious personal injuries as well as damage to the product. The screw and hole should come together with over 5/16 inch (8 mm) length of thread. Use a bracket which has been approved for UL1678 standard, and which can endure at least 4 times or more the weight of the monitor.

Page 64

Specications

Power management

This monitor conforms to VESA DPMS. Both your video card and computer must support the same standard in order for the monitor’s power management function to work.

DPMS: Display Power Management Signaling

DPMS Screen

ON STATE Display 280 W Yes Yes STANDBY SUSPEND Yes No

OFF STATE No No

display

* When CONNECT AUTO INPUT SELECT and NO SIGNAL AUTO INPUT SEL. are set to OFF.

DDC (plug and play)

The monitor supports the VESA DDC (Display Data Channel) standard. DDC is a signal standard for plug and play between monitors and computers. Information about resolution and other parameters

is exchanged between the two. This function can be used if the computer supports DDC and it has been congured to detect

plug-and-play monitors. There are several types of DDC, depending on the communication method used. This monitor supports DDC2B.

Compatible signal timing (PC)

Power

consumption

6.0 W*

Hsync Vsync

No Yes

Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Digital

Yes Yes Yes

Yes Yes Yes Yes

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Screen resolution Hsync Vsync Dot frequency

VESA

Wide

US TEXT Sun

* Displays a reduced image, except in Dot by Dot. In Dot by Dot, the image will be cut down to panel size then displayed.

• Depending on the connected PC, images may not be displayed properly even if the compatible signal described above is input.

• The frequency values for the Sun are reference values.

640 × 480

800 × 600

848 × 480

1024 × 768

1152 × 864 1280 × 768

1280 × 800 1280 × 960

1280 × 1024

1360 × 768

1400 × 1050

1440 × 900

1600 × 1200*

1680 × 1050

1920 × 1200*

1280 × 720

1920 × 1080

720 × 400

1024 × 768

1152 × 900

1280 × 1024

1600 × 1000

31.5kHz

37.9kHz

37.5kHz

35.1kHz

37.9kHz

48.1kHz

46.9kHz

31.0kHz

48.4kHz

56.5kHz

60.0kHz

67.5kHz

47.8kHz

60.3kHz

49.7kHz

60.0kHz

64.0kHz

80.0kHz

47.7kHz

65.3kHz

55.9kHz

75.0kHz

65.3kHz

74.0kHz

44.7kHz

67.5kHz

31.5kHz

48.3kHz

53.6kHz

56.6kHz

61.8kHz

71.8kHz

71.7kHz

81.1kHz

68.6kHz

60Hz 72Hz 75Hz 56Hz 60Hz 72Hz 75Hz 60Hz 60Hz 70Hz 75Hz 75Hz 60Hz 75Hz 60Hz 60Hz 60Hz 75Hz 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz 60Hz 70Hz 60Hz 66Hz 70Hz 66Hz

76.2Hz

67.2Hz 76Hz 66Hz

25.175MHz

31.5MHz

36.0MHz

40.0MHz

50.0MHz

49.5MHz

33.75MHz

65.0MHz

75.0MHz

78.75MHz

108.0MHz

79.5MHz

102.25MHz

83.5MHz

108.0MHz

135.0MHz

85.5MHz

121.75MHz

106.5MHz

162.0MHz

146.25MHz

154.0MHz

74.4MHz

148.5MHz

28.3MHz

64.13MHz

70.4MHz

74.25MHz

94.88MHz

108.23MHz

117.01MHz

134.99MHz

135.76MHz

DisplayPortHDMI

Analog

(D-SUB)

Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes Yes

Page 65

Compatible signal timing (AV)

Screen resolution Frequency HDMI Component

1920 × 1080p 24Hz Ye s -

1920 × 1080i 50Hz Yes Yes

1280 × 720p 50Hz Yes Yes

720 × 576p 50Hz Ye s Ye s 720 × 480p 59.94Hz Yes Yes

640 × 480p(VGA) 59.94Hz Yes -

720(1440) × 576i 50Hz Yes Yes 720(1440) × 480i 59.94Hz Yes Yes

Specications

50Hz Ye s Ye s

59.94Hz Yes Yes 60Hz Ye s Ye s

60Hz Ye s Ye s

60Hz Ye s -

60Hz Ye s Ye s

Page 66

Specications

D-sub input terminal pins

(Mini D-sub 15 pin)

No. Function No. Function

1 Red video signal input 9 +5V 2 Green video signal input 10 GND 3 Blue video signal input 11 N.C. 4 N.C. 12 DDC data 5 GND 13 Hsync signal input 6 GND for red video signal 14 Vsync signal input 7 GND for green video signal 15 DDC clock 8 GND for blue video signal

HDMI input terminal pins

(HDMITM Connector)

No. Function No. Function

1 TMDS data 2+ 11 TMDS clock shield 2 TMDS data 2 shield 12 TMDS clock3 TMDS data 2- 13 CEC 4 TMDS data 1+ 14 N.C. 5 TMDS data 1 shield 15 SCL 6 TMDS data 1- 16 SDA 7 TMDS data 0+ 17 DDC/CEC GND 8 TMDS data 0 shield 18 +5V 9 TMDS data 0- 19 Hot-plug detection

10 TMDS clock+

DisplayPort input terminal pins

(DisplayPort 20 pin)

No. Function No. Function

1 MainLane 3- 11 Gnd 2 Gnd 12 MainLane 0+ 3 MainLane 3+ 13 Gnd 4 MainLane 2- 14 Gnd 5 Gnd 15 Aux + 6 MainLane 2+ 16 Gnd 7 MainLane 1- 17 Aux 8 Gnd 18 Hot-plug detection 9 MainLane 1+ 19 Gnd

10 MainLane 0- 20 3.3V

DisplayPort output terminal pins

(DisplayPort 20 pin)

No. Function No. Function

1 MainLane 0+ 11 Gnd 2 Gnd 12 MainLane 33 MainLane 0- 13 Gnd 4 MainLane 1+ 14 Gnd 5 Gnd 15 Aux + 6 MainLane 1- 16 Gnd 7 MainLane 2+ 17 Aux 8 Gnd 18 Hot-plug detection 9 MainLane 2- 19 Gnd

10 MainLane 3+ 20 3.3V

Page 67

Mounting Precautions

(For SHARP dealers and service engineers)

• When installing, removing or moving the monitor, ensure that this is carried out by at least 4 people.

• Be sure to use a wall-mount bracket designed or designated for mounting the monitor.

• This monitor is designed to be installed on a concrete wall or pillar. Reinforced work might be necessary for some materials

such as plaster / thin plastic board / wood before starting installation. This monitor and bracket must be installed on a wall which can endure at least 4 times or more the weight of the monitor. Install by the most suitable method for the material and the structure.

• To attach a VESA-compliant mounting bracket, use M6 screws that are 5/16 inch (8 mm) to 3/8 inch (10 mm) longer than the

thickness of the mounting bracket.

5/16 - 3/8 inch (8-10 mm)

Screws (M6) Mounting bracket Monitor mounting

• Do not use an impact driver.

• After mounting, please carefully ensure the monitor is secure, and not able to come loose from the wall or mount.

• Do not use any screw holes other than VESA holes for installation.

• When moving the monitor, be sure to hold it with the handles and the unit bottom. Do not grasp the screen, tray, speaker, or

speaker cover. This may cause product damage, failure, or injury.

• If you need to temporarily place the monitor on a table or other surface during installation, spread a thick soft cloth on the

table to prevent damage to the screen and table.

• Prior to repacking or removal, remove the tray and speaker covers.

Attaching the Tray

Tray mount fitting

Caution

• When attaching the tray, do not pinch the USB cable on the back

of the tray.

The USB cable on the back of the tray can be fastened with the cable clamp to the rear of the monitor.

*1 *1

Push until the tabs lock into place (4 places)

*2 *2

Tabs (4 places)

Page 68

Mounting Precautions (For SHARP dealers and service engineers)

Removing the Tray

Back of the tray

Pinch the locking tabs (4 places)

(1)

Attaching the speaker covers

(2)

Speaker cover attachment screws (M3)

If you will use the monitor in a portrait orientation, the speaker cover is not used.

Removing the tray mount tting

If you will use the monitor in a portrait orientation or will otherwise not use the tray, remove the tray mount tting.

Page 69

PN-80TC3 M EN16C(2)