Sharp PG-D2870W, PG-F267X Installation Manual

MODEL AN-STWM20

INSTALLATION INSTRUCTIONS FOR SHORT THROW PROJECTOR
WALL MOUNTING BRACKET FOR USE WITH SHARP PROJECTOR
MODEL NOS. PG-F267X, PG-D2870W

COLOR: WHITE

AN-STWM20 SHORT THROW
WALL MOUNTING BRACKET
WITH EXTENSION

AVDEX CORPORATION

115 HENRY STREET, FREEPORT, NY 11520

TEL: [phone] FAX: [phone] TOLL FREE: 1-800-866-1820

E-MAIL: [e-mail]

INSTALLATION INSTRUCTIONS

INSTALLATION OF THIS ADJUSTABLE WALL MOUNTING
BRACKET SHOULD BE PERFORMED BY QUALIFIED SERVICE/
INSTALLATION PERSONNEL FOLLOWING THE INSTALLATION
INSTRUCTIONS INCLUDED WITH THIS BRACKET

THE EXCLAMATION POINT WITHIN AN EQUILATERAL TRIANGLE
IS INTENDED TO ALERT THE USER TO THE PRESENCE OF IMPORTANT
OPERATING AND MAINTENANCE (SERVICING) I N STRUCTIONS IN THE
LITERATURE ACCOMPANYING THE APPLIANCE.

IMPORTANT! THE INSTALLER SHOULD READ THESE INSTRUCTIONS
THOROUGHLY BEFORE BEGINNING THE INSTALLATION AND SHOULD MAKE SURE
THAT ALL THE WORK IS DONE IN COMPLIANCE WITH NEC AND ALL LOCAL
BUILDING AND SAFETY CODES. SAVE THIS BOOKLET AFTER THE INSTALLATION
IS COMPLETED. THE ACCESSORIES REFERRED TO IN THESE INSTRUCTIONS ARE
INTENDED FOR USE ONLY WITH COMPATIBLE SHARP PROJECTORS. SEE
SHARP PROJECTOR OWNER’S MANUAL OR SHARP DEALER TO DETERMINE
SUITABILITY.

SHORT THROW PROJECTOR WALL
MOUNTING BRACKET AN-STWM20

C A U T I O N

CAUTION: THE BRACKET MOUNTING SCREWS MUST GO DIRECTLY INTO THE
BEAMS. SHEETROCK, LATH AND PLASTER, WILL NOT PROVIDE A
SUFFICIENTLY SECURE SUPPORT.

CAUTION: TO REDUCE THE RISK OF PERSONAL INJURY, USE ONLY THE
COMPONENTS WHICH ARE INCLUDED IN THIS PACKAGE, OR SPECIFIED IN
THESE INSTRUCTIONS.

PARTS LIST FOR MODEL AN-STWM20
SHORT THROW PROJECTOR WALL MOUNTING BRACKET (SEE FIG. 1)

ITEM DESCRIPTION QUANTITY

A. MOUNTING TWIST ASSEMBLY FOR ATTACHMENT TO BOTTOM OF PROJECTOR INCLUDES
DUAL POSITIONING ASSEMBLY 1
B. MAIN WALL MOUNTING BRACKET ASSEMBLY WHICH INCLUDES OUTER EXTENSION TUBE 1
C. DIAGONAL BRACE 1
D. INNER EXTENSION TUBE 1
E. END STOP FOR INNER EXTENTION TUBE 1
F. 1/4 X 10 HEX HEAD LAG BOLTS 2-1/2” LONG 4
G. 1/4 X 10 HEX HEAD LAG BOLTS 3” LONG 4
H. 1/4” I.D. WASHERS FOR USE WITH LAG BOLTS 4
I. M4X10 SCREWS AND WASHERS FOR USE WITH PROJECTOR ATTACHMENT PLATE 4
J. 1/4-20 X 1/2” KNOB 2
K. 1/4-20 X 1/4” BUTTON HEAD SOCKET CAP SCREW WITH WASHERS (BLACK) FOR EXTENSION TUBE 6
L. 1/4-20 X 5/16” BUTTON HEAD SOCKET CAP SCREW FOR DIAGONAL BRACE AND END STOP 3
M. 1/4-20 NYLON CAP NUTS 2
N. 5/32 AND 7/32 ALLEN WRENCHES 2

PAGE 2

INSTALLATION INSTRUCTIONS

FIGURE 1. ILLUSTRATION OF PARTS FOR WALL MOUNTING BRACKET

SHORT THROW PROJECTOR WALL
MOUNTING BRACKET AN-STWM20

C.

E.

D.

L.

M

F.

G.

B. A.

D.

H.

I.

J

K.

N.

INVERT THE PROJECTOR IMAGE

Please refer to the owners manual for your LCD Projector for detailed instructions of how to electrically
invert the projected image to accommodate its use in the wall mounted mode.

LOCATION OF THE WALL MOUNTING BRACKET

Please refer to the owner’s manual for your SHARP LCD PROJECTOR for information which will help
you to determine the best location for the placement of the wall mounting bracket assembly.

INSTALLATION OF THE WALL MOUNTING BRACKET

After you have determined the appropriate location for the bracket, you must locate the exact
location of the wall studs. Most standard residential construction uses 16 inches between centers
for wall studs. You can mount the bracket in line with a single beam.

CAUTION: THE BRACKET MOUNTING SCREWS MUST GO DIRECTLY INTO THE STUDS.
SHEETROCK, LATH AND PLASTER, WILL NOT PROVIDE A SUFFICIENTLY SECURE
SUPPORT.

FOR WALLS MADE OF CEMENT BLOCK, BRICK OR SOLID MASONRY,
EXPANSION ANCHORS SHOULD BE USED.

PAGE 3