Sharp PG-C355W, XG-C455W Operating Manual

Download

Introduction

DATA PROJECTOR

MODEL

XG-C455W PG-C355W

OPERATION MANUAL

Quick Start

Setup

Connections

Basic Operation

Useful Features

Appendix

IMPORTANT

• For your assistance in reporting the loss or theft of your Projector, please record the Model and Serial Numbers located on the bottom of the projector and retain this information.

• Before recycling the packaging, please ensure that you have checked the contents of the carton thoroughly against the list of “Supplied accessories” on page 10.

SPECIAL NOTE FOR USERS IN THE U.K.

The mains lead of this product is fitted with a non-rewireable (moulded) plug incorporating a 10A fuse. Should the fuse need to be replaced, a BSI or ASTA approved BS 1362 fuse marked above, which is also indicated on the pin face of the plug, must be used. Always refit the fuse cover after replacing the fuse. Never use the plug without the fuse cover fitted. In the unlikely event of the socket outlet in your home not being compatible with the plug supplied, cut off the mains plug and fit an appropriate type.

DANGER:

The fuse from the cut-off plug should be removed and the cut-off plug destroyed immediately and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted elsewhere into a 10A socket outlet, as a serious electric shock may occur. To fit an appropriate plug to the mains lead, follow the instructions below:

WARNING:

THIS APPARATUS MUST BE EARTHED.

IMPORTANT:

The wires in this mains lead are coloured in accordance with the following code:

Green-and-yellow : Earth / Blue : Neutral / Brown : Live As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug proceed as follows:

Model No.:

Serial No.:

or and of the same rating as

• The wire which is coloured green-and-yellow must be connected to the terminal in the plug which is marked by

the letter E or by the safety earth symbol

or coloured green or green-and-yellow.

• The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black.

• The wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red.

IF YOU HAVE ANY DOUBT, CONSULT A QUALIFIED ELECTRICIAN.

The supplied CD-ROM contains operation instructions in English, German, French, Spanish, Italian, Dutch, Swedish, Portuguese, Chinese and Korean. Carefully read through the operation instructions before operating the projector.

Die mitgelieferte CD-ROM enthält Bedienungsanleitungen in Englisch, Deutsch, Französisch, Spanisch, Italienisch, Niederländisch, Schwedisch, Portugiesisch, Chinesisch und Koreanisch. Bitte lesen Sie die Bedienungsanleitung vor der Verwendung des Projektors sorgfältig durch.

Le CD-ROM fourni contient les instructions de fonctionnement en anglais, allemand, français, espagnol, italien, néerlandais, suédois, portugais, chinois et coréen. Veuillez lire attentivement ces instructions avant de faire fonctionner le projecteur.

El CD-ROM suministrado contiene instrucciones de operación en inglés, alemán, francés, español, italiano, holandés, sueco, portugués, chino y coreano. Lea cuidadosamente las instrucciones de operación antes de utilizar el proyector.

Il CD-ROM in dotazione contiene istruzioni per l’uso in inglese, tedesco, francese, spagnolo, italiano, olandese, svedese, portoghese, cinese e coreano. Leggere attentamente le istruzioni per l’uso prima di usare il proiettore.

De meegeleverde CD-ROM bevat handleidingen in het Engels, Duits, Frans, Spaans, Italiaans, Nederlands, Zweeds, Portugees, Chinees en Koreaans. Lees de handleiding zorgvuldig door voor u de projector in gebruik neemt.

Den medföljande CD-ROM-skivan innehåller bruksanvisningar på engelska, tyska, franska, spanska, italienska, holländska, svenska, portugisiska, kinesiska och koreanska. Läs noga igenom bruksanvisningen innan projektorn tas i bruk.

O CD-ROM fornecido contém instruções de operação em Inglês, Alemão, Francês, Espanhol, Italiano, Holandês, Sueco, Português, Chinês e Coreano. Leia cuidadosamente todas as instruções de operação antes de operar o projetor.

Before using the projector, please read this operation manual carefully.

Introduction

ENGLISH

There are two important reasons for prompt warranty registration of your new SHARP Projector, using the REGISTRATION CARD packed with the projector.

1. WARRANTY

This is to assure that you immediately receive the full benefit of the parts, service and labor warranty applicable to your purchase.

2. CONSUMER PRODUCT SAFETY ACT

To ensure that you will promptly receive any safety notification of inspection, modification, or recall that SHARP may be required to give under the 1972 Consumer Product Safety Act, PLEASE READ CAREFULLY THE IMPORTANT “LIMITED WARRANTY” CLAUSE.

U.S.A. ONLY

WARNING: High brightness light source. Do not stare into the beam of light, or view directly. Be especially

careful that children do not stare directly into the beam of light.

WARNING: To r educe the risk of fire or electric shock, do not expose this product to

rain or moisture.

See bottom of projector.

CAUTION

RISK OF ELECTRIC SHOCK.

DO NOT REMOVE SCREWS

EXCEPT SPECIFIED USER

SERVICE SCREW.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk or electric shock to persons.

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

NO USER-SERVICEABLE PARTS EXCEPT LAMP UNIT.

WARNING:

DO NOT REMOVE COVER.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

The exclamation point within a triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

U.S.A. ONLY

INFORMATION

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the operation manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference, in which case the user will be required to correct the interference at his own expense.

The enclosed computer cable must be used with the device. The cable is provided to ensure that the device complies with FCC Class A verification.

U.S.A. ONLY

WARNING:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

-1

PRODUCT DISPOSAL

This product utilizes tin-lead solder, and lamp containing a small amount of mercury. Disposal of these materials may be regulated due to environmental considerations. For disposal or recycling information, please contact your local authorities, the Electronics Industries Alliance: www.eiae.org, the lamp recycling organization www.lamprecycle.org, or Sharp at 1-800-BE-SHARP.

U.S.A. ONLY

Caution Concerning Lamp Replacement

See “Replacing the Lamp” on page 61.

This SHARP projector uses an LCD (Liquid Crystal Display) panel. This very sophisticated panel contains 1,024,000 pixels (x RGB) TFT’s (Thin Film Transistors). As with any high technology electronic equipment such as large screen TVs, video systems and video cameras, there are certain acceptable tolerances that the equipment must conform to. This unit has some inactive pixels within acceptable tolerances which may result in inactive dots on the picture screen. This will not affect the picture quality or the life expectancy of the unit.

• Microsoft® and Windows® are registered trademarks of Microsoft Corporation in the United States and/or

other countries.

• PC/AT is a registered trademark of International Business Machines Corporation in the United States.

• Adobe

• Macintosh

• PJLink is a registered trademark or an application trademark in Japan, the United States and/or other

• All other company or product names are trademarks or registered trademarks of their respective compa-

Reader® is a trademark of Adobe Systems Incorporated.

is a registered trademark of Apple Computer, Inc. in the United States and/or other countries.

countries/regions.

nies.

Authorized representative responsible for the European Union Community Market

SHARP ELECTRONICS (Europe) GmbH Sonninstraße 3, D-20097 Hamburg

E.U. ONLY

-2

How to Read this Operation Manual

••

• In this operation manual, the illustrations and on-screen displays are simplified for explana-

••

tion. This may differ from the actual on-screen display.

Using the Menu Screen

Introduction

Buttons used in this operation

Button used in this step

Adjustment buttons ('/"/\/|)

ENTER button

MENU button

RETURN button

MOUSE/Adjustment buttons ('/"/\/|)

ENTER button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

Press MENU.

• The “Picture” menu screen for the selected input mode is displayed.

Press ture” to adjust.

| or

\ and select “Pic-

Example: “Picture” screen menu

Picture SIG SCR PRJ Net.

Picture Mode

Contrast 0 Bright Color Tint

Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode

Reset

SEL./ADJ. RETURN

Menu item

0 0 0 0Sharp 0 0

MENU button

RETURN button

• Press RETURN to return to previous screen when the menu is displayed

Standard

7500K 3D Progressive Auto Off Off Off

ENTER END

Buttons used in this operation

On-screen display

Useful Features

-43

Info

...........Indicates safeguards when using the projector.

........Indicates additional information for setting up and operating the projector.

Note

For Future Reference

Maintenance Troubleshooting Index

Page 56

Pages 66 and 67

Page 70

-3

Preparing

Introduction

How to Read this Operation Manual............. 3

Contents.......................................................... 4

How to Access the PDF Operation Manuals ....

IMPORTANT SAFEGUARDS .......................... 7

Accessories .................................................. 10

Part Names and Functions .......................... 12

Using the Remote Control ........................... 15

Usable Range .................................................... 15

Inserting the Batteries .......................................15

Quick Start

Quick Start .................................................... 16

Setup

Setting Up the Projector .............................. 18

Setting Up the Projector .................................... 18

Projection (PRJ) Mode ....................................... 19

Connections

Samples of Cables for Connection............. 21

Connecting to a Computer .......................... 23

Connecting to Video Equipment ................. 25

Controlling the Projector by a Computer... 27 Connecting to a Monitor with RGB

Input Terminal ......................................... 28

Connecting to an Amplifier or Other

Audio Equipment .................................... 29

Using

Basic Operation

Turning the Projector On/Off ....................... 30

Connecting the Power Cord .............................. 30

Tu rning the Projector On .................................... 30

Tu rning the Power Off (Putting the Projector into

Standby Mode)............................................ 30

Image Projection .......................................... 31

Using the Adjustment Feet ................................ 31

Correcting Trapezoidal Distortion ...................... 32

Adjusting the Lens ............................................. 33

Switching the Input Mode .................................. 34

Adjusting the Volume......................................... 34

Displaying the Black Screen and Turning off

the Sound Temporarily ................................ 34

Displaying and Setting the Break Timer ............ 35

Switching the Eco+Quiet Mode ......................... 35

Auto Sync (Auto Sync Adjustment) ................... 35

Freezing a Moving Image .................................. 35

Selecting the Picture Mode ............................... 36

Displaying an Enlarged Portion of an Image .... 36

Resize Mode ...................................................... 37

Using the Remote Control as the Wireless

Computer Mouse ........................................ 39

Useful Features

Menu Items ................................................... 40

Using the Menu Screen ............................... 43

Menu Selections (Adjustments) ......................... 43

Picture Adjustment (“Picture” menu) ........ 45

Selecting the Picture Mode ............................... 45

Adjusting the Image .......................................... 45

Adjusting the Color Temperature ....................... 45

Selecting the Progressive Mode........................ 46

Selecting the Film Mode .................................... 46

Reducing Image Noise (DNR) ........................... 46

Mosquito Noise Reduction (MNR) ..................... 46

Eco+Quiet Mode Setting ................................... 46

Signal Adjustment (“SIG-ADJ” Menu) ........ 47

Adjusting the Computer Image ......................... 47

Resolution Setting .............................................. 47

Auto Sync Adjustment ....................................... 47

Signal Type Setting ............................................ 47

Selecting the Dynamic Range ........................... 48

Setting the Video System................................... 48

Checking the Input Signal ................................. 48

Screen Adjustment (“SCR-ADJ” Menu) ..... 49

Setting the Resize Mode ................................... 49

Adjusting the Image Position ............................. 49

Keystone Correction .......................................... 49

Setting the On-screen Display........................... 50

Selecting a Startup and Background Image ..... 50

Selecting the Menu Screen Position .................. 50

Reversing/Inverting Projected Images .............. 50

Selecting the On-screen Display Language ..... 50

Helpful Functions Set during Installation

(“PRJ-ADJ” menu) ................................. 51

Auto Power Off Function .................................... 51

Auto Restart Function ........................................ 51

Setting the Confirmation Sound

(System Sound) ........................................... 51

Speaker Setting ................................................. 51

Audio Output Type Setting ................................ 51

Monitor Output ................................................... 51

LAN/RS232C ..................................................... 51

Selecting the Transmission Speed (RS-232C) .. 52

Fan Mode Setting .............................................. 52

System Lock Function ....................................... 52

Keylock Function ............................................... 53

Returning to the Default Settings ....................... 53

Checking the Lamp Life Status ......................... 53

Setting up the Projector Network

Environment (“Network” menu) ............ 54

Setting a Password ............................................ 54

DHCP Client Setting .......................................... 55

TCP/IP Setting ................................................... 55

Confirming the Projector Information ................. 55

-4

Reference

Appendix

Maintenance ................................................. 56

Replacing the Air Filter ................................ 57

Replacing the Air Filter ...................................... 57

Maintenance Indicators ............................... 59

Regarding the Lamp .................................... 61

Lamp .................................................................61

Caution Concerning the Lamp .......................... 61

Replacing the Lamp .......................................... 61

Removing and Installing the Lamp Unit ............ 62

Resetting the Lamp Timer ................................. 63

Storing the Projector ................................... 64

How to Use the Storage Case ........................... 64

Computer Compatibility Chart .................... 65

Troubleshooting ........................................... 66

For SHARP Assistance ................................ 68

Specifications ............................................... 69

Index .............................................................. 70

SETUP MANUAL

Introduction

Refer to the “SETUP MANUAL” contained on the supplied CDROM for details.

Setting up the Screen .................................... 2

Screen Size and Projection Distance ........... 3

Changing the Lens ......................................... 9

Connecting Pin Assignments ..................... 11

RS-232C Specifications and Commands ... 13 Setting up the Projector Network

Environment............................................ 18

Controlling the Projector via LAN .............. 24

Setting up the Projector Using

RS-232C or Telnet ................................... 29

Resetting the Lamp Timer

of the Projector via LAN......................... 39

Troubleshooting ........................................... 41

Dimensions ................................................... 44

-5

How to Access the PDF Operation Manuals

PDF operation manuals in several languages are included in the CD-ROM, so that you can work with the projector. To utilize these manuals, you need to install Adobe® Reader® on your computer (Windows® or Macintosh®).

Please download Adobe® Reader® from the Internet (http://www.adobe.com).

Accessing the PDF Manuals

For Windows®:

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “My Computer” icon. 3 Double click the “CD-ROM” drive. 4

When you want to view the operation manual

1) Double click the “MANUALS” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf file to access the projector manuals.

When you want to view the setup manual

1) Double click the “SETUP” folder.

2) Double click the language (name of the folder) that you want to view.

3) Double click the pdf file to access the setup manual.

For Macintosh

1 Insert the CD-ROM in the CD-ROM drive. 2 Double click the “CD-ROM” icon. 3

When you want to view the operation manual

1) Double click the “MANUALS” folder.

2) Double click the language (name of the

3) Double click the pdf file to access the pro-

When you want to view the setup manual

1) Double click the “SETUP” folder.

2) Double click the language (name of the

3) Double click the pdf file to access the setup

folder) that you want to view.

jector manuals.

folder) that you want to view.

manual.

Info

• If the desired pdf file cannot be opened by double clicking the mouse, start Adobe® Reader® first, then specify the desired file using the “File”, “Open” menu.

-6

IMPORTANT SAFEGUARDS

CAUTION: Please read all of these instructions before you operate this product and save these

instructions for later use.

Electrical energy can perform many useful functions. This product has been engineered and manufactured to assure your personal safety. BUT IMPROPER USE CAN RESULT IN POTENTIAL ELECTRICAL SHOCK OR FIRE HAZARDS. In order not to defeat the safeguards incorporated in this product, observe the following basic rules for its installation, use and servicing.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Retain Instructions

The safety and operating instructions should be retained for future reference.

3. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

4. Follow Instructions

All operating and use instructions should be followed.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

7. Water and Moisture

Do not use this product near water–for example, near a bath tub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

8. Accessories

Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

9. Transportation

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Grounding or Polarization

This product is provided with one of the following types of plugs. If the plug should fail to fit into the power outlet, please contact your electrician. Do not defeat the safety purpose of the plug.

a. Two-wire type (mains) plug. b. Three-wire grounding type (mains) plug with a

grounding terminal. This plug will only fit into a grounding type power outlet.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

14. Lightning

For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent damage to the product due to lightning and power-line surges.

15. Overloading

Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.

16. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

17. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

18. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. When the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into

the product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following

the operating instructions. Adjust only those controls

that are covered by the operating instructions, as an

improper adjustment of other controls may result in

damage and will often require extensive work by a

qualified technician to restore the product to normal

operation. e. If the product has been dropped or damaged in any

way. f. When the product exhibits a distinct change in

performance, this indicates a need for service.

19. Replacement Parts

When replacement parts are required, ensure that the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

20. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

21.Wall or Ceiling Mounting

This product should be mounted to a wall or ceiling only as recommended by the manufacturer.

22. Heat

This product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Introduction

-7

IMPORTANT SAFEGUARDS

Ensure that you read the following safeguards when setting up your projector.

Caution concerning the lamp unit

■ Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp Authorized Projector Dealer or Service Center for replacement. See “Regarding the Lamp” on page 61.

CAUTION PRECAUCIÓN PRÉCAUTION

Caution concerning the setup of the projector

■ For minimal servicing and to maintain high image quality, SHARP recommends that this projector be installed in an area free from humidity, dust and cigarette smoke. When the projector is subjected to these environments, the vents and lens must be cleaned more often. As long as the projector is regularly cleaned, use in these environments will not reduce the overall operation life of the unit. Internal cleaning should only be performed by a Sharp Authorized Projector Dealer or Service Center.

Do not set up the projector in places exposed to direct sunlight or bright light.

■ Position the screen so that it is not in direct sunlight or room light. Light falling directly on the screen washes out the colors, making viewing difficult. Close the curtains and dim the lights when setting up the screen in a sunny or bright room.

The projector may be safely tilted to a maximum angle of 9 degrees.

■ Placement should be within ±9 degrees of horizontal.

When using the projector in high-altitude areas such as mountains (at altitudes of approximately 1,500 meters (4,900 feet) or more)

■ When you use the projector in high-altitude areas with thin air, set “Fan Mode” to “High”. Neglecting this can affect the longevity of the optical system.

-8

Warning about placing the projector in a high position

■ When placing the projector in a high position, make certain it is carefully secured to avoid personal injury caused by the projector falling down.

Do not subject the projector to hard impact and/or vibration.

■ Ta ke care with the lens so as not to hit or damage the surface of the lens.

Rest your eyes occasionally.

■ Continuously watching the screen for long hours will cause eye strain. Take regular breaks to rest your eyes.

Avoid locations with extremes of temperature.

■ The operating temperature of the projector is from 41°F to 95°F (+5°C to +35°C).

■ The storage temperature of the projector is from –4°F to 140°F (–20°C to +60°C).

Do not block the intake and exhaust vents.

■ Allow at least 7 7/8 inches (20 cm) of space between the exhaust vent and the nearest wall or obstruction.

■ Ensure that the intake vent and the exhaust vent are not obstructed.

■ If the cooling fan becomes obstructed, a protection circuit will automatically put the projector into standby mode to prevent overheat damage. This does not indicate a malfunction (see pages 59 and 60). Remove the pro- jector power cord from the wall outlet and wait at least 10 minutes. Place the projector where the intake and exhaust vents are not blocked, plug the power cord back in and turn on the projector. This will return the projector to the normal operating condition.

Caution regarding usage of the projector

■ When using the projector, take care not to subject it to hard impact and/or vibration, as this can result in damage. Take extra care with the lens. If you are not to use the projector for a long time, make certain you unplug the power cord from the wall outlet, and disconnect any other cables connected to it.

■ Do not carry the projector by holding the lens.

■

When storing the projector, ensure you attach the lens cap to the projector. (See page 12.)

■ Do not expose the storage case or projector to direct sunlight or near heat sources. The storage case or projector may change color or become deformed.

Other connected equipment

■ When connecting a computer or other audiovisual equipment to the projector, make the connections AFTER unplugging the power cord of the projector from the AC outlet and turning off the equipment to be connected.

■ Please read the operation manuals of the projector and the equipment to be connected for instructions on how to make the connections.

Introduction

Info

• The cooling fan regulates the internal temperature, and its performance is automatically controlled. The sound of the fan may change during projector operation due to changes in the fan speed. This does not indicate malfunction.

Using the projector in other countries

■ The power supply voltage and the shape of the plug may vary depending on the region or country you are using the projector in. When using the projector overseas, make sure you use an appropriate power cord for the country you are in.

Temperature monitor function

■

If the projector starts to overheat due to setup problems or blockage of the air vents, “ ” and “ ” will illuminate in the lower left corner of the picture. If the temperature continues to rise, the lamp will turn off, the temperature warning indicator on the projector will blink, and after a 90-second cooling-off period the projector will enter the standby mode. Refer to “Maintenance Indicators” on page 59 for details.

-9

Accessories

Supplied accessories

Remote control <RRMCGA623WJSA>

Power cord

(1)

Tw o R-6 batteries (“AA” size, UM/SUM-3, HP-7 or similar)

(2) (3)

RGB cable (10' (3.0 m)) <QCNWGA045WJPZ>

DIN-D-sub RS-232C adaptor (5

57/64" (15 cm))

(4)

For U.S., Canada, etc. (6' (1.8 m)) <QACCDA007WJPZ>

For Europe, except U.K. (6' (1.8 m)) <QACCVA011WJPZ>

For U.K., Hong Kong and Singapore (6' (1.8 m)) <QACCBA036WJPZ>

For Australia, New Zealand and Oceania (6' (1.8 m)) <QACCLA018WJPZ>

*Use the power cord that corresponds to the wall outlet in your country.

Lens cap (attached) <PCAPHA026WJSA>

• Operation manual (this manual <TINS-D563WJZZ> and CD-ROM <UDSKAA102WJZZ>)

Lens cap strap <UBNDTA017WJZZ>

Note

• Codes in “< >” are Replacement parts codes.

Optional accessories

■ Lamp unit AN-C430LP

■ Ceiling-mount adaptor AN-60KT

AN-XGCM55 (for U.S.A. only)

■ Universal bracket AN-JT200 (for U.S.A. only)

■ Ceiling-mount unit AN-TK201 <for AN-60KT>

AN-TK202 <for AN-60KT> AN-EP101B <for AN-XGCM55 and AN-JT200> (for U.S.A. only)

■ Remote receiver AN-MR2

■ 3 RCA to 15-pin D-sub cable (10' (3.0 m)) AN-C3CP2

Storage case <GCASNA020WJSA>

Note

• Some of the optional accessories may not be available depending on the region. Please check with your nearest Sharp Authorized Projector Dealer or Service Center.

-10

Optional lenses

■ Lens Projection distance for 100" screen size

Wide-zoom lens (× 1.5 – 1.9) AN-C12MZ 10' 5" – 13' 1" (3.2 m – 4.0 m) Tele-zoom lens (× 2.2 – 2.8) AN-C18MZ 15' 7" – 19' 10" (4.8 m – 6.0 m) Tele-zoom lens (× 3.3 – 5.1) AN-C27MZ 23' 2" – 35' 8" (7.1 m – 10.9 m) Tele-zoom lens (× 5.1 – 7.2) AN-C41MZ 36' 2" – 50' 10" (11.0 m – 15.5 m)

The standard zoom lens is attached to the projector. The optional lenses from Sharp are also available for specialized application. Please see your nearest Sharp Authorized Projector Dealer for details on all the lenses. (Refer to the SETUP MANUAL on the supplied CD-ROM for details.) Also, be sure to have service personnel install the optional lenses.

Throw Distance

The graph below is for 100 inches (254 cm) screen with 16:10 Signal Input (Normal Mode).

Screen

Wide-zoom lens (AN-C12MZ) 10'5"–13'1" (3.2 m–4.0 m) Throw distance ratio 1:1.5–1.9

Introduction

Standard zoom lens 12'4"–14'9" (3.8 m–4.5 m) Throw distance ratio 1:1.8–2.1

Tele-zoom lens (AN-C18MZ) 15'7"–19'10" (4.8 m–6.0 m) Throw distance ratio 1:2.2–2.8

Tele-zoom lens (AN-C27MZ) 23'2"–35'8" (7.1 m–10.9 m) Throw distance ratio 1:3.3–5.1

Tele-zoom lens (AN-C41MZ) 36'2"–50'10" (11.0 m–15.5 m) Throw distance ratio 1:5.1–7.2

10 20 30 5040 55(ft)

-11

Part Names and Functions

Numbers in refer to the main pages in this operation manual where the topic is explained.

Projector

Top View

Power indicator

STANDBY/ON button

For turning the power on and

putting the projector into

standby mode.

KEYSTONE button

For entering the Keystone

Correction mode.

Adjustment buttons

('/"/\/|)

For selecting and adjusting

on-screen items.

RETURN button

For returning to the previous

display.

INPUT buttons

For switching input mode.

30·59

Lamp indicator

Temperature warning indicator

AUTO SYNC button

For automatically adjusting images when connected to a computer.

ENTER button

For setting items selected or adjusted on the menu.

Volume buttons

For adjusting the speaker sound level.

MENU button

For displaying adjustment and setting screens.

Front View

Zoom knob

For enlarging/

reducing the picture.

Tilt dial

Height Adjustment

button

Adjustment foot

Push both sides of the lens cap to

Attaching the lens cap

After putting the lens cap strap on the lens cap, pass the other end of the strap through the hole on the front side of the projector, next to the lens, as shown in the illustration.

attach or remove.

56·57

ECO+QUIET button

For lowering the noise of the cooling fan and extending the lamp life.

Focus ring

For adjusting the focus.

Speaker

Remote control sensor

Height Adjustment button

Adjustment foot

Air filter/Intake vent

(on the bottom of the projector)

-12

Projector (Rear View)

Terminals

Introduction

COMPUTER/COMPONENT 2 input terminal

Terminal for Computer RGB and Component signals.

AUDIO input terminal

Audio input terminal for

COMPUTER/COMPONENT 1.

COMPUTER/COMPONENT 1

input terminal

Terminal for Computer RGB

and Component signals.

S-VIDEO input terminal

VIDEO input terminal

AUDIO input terminal

for S-video

AUDIO input terminal

Output terminal for Computer RGB and

Shared for COMPUTER/COMPONENT 1 and 2.

23·25

for Video

MONITOR output terminal

Component signals.

23·25

AUDIO input terminal

Shared audio input terminal for COMPUTER/COMPONENT 2 and DVI-D.

24·25

DVI-D input terminal

Terminal for DVI Digital RGB and Digital Component signals.

USB terminal

Terminal connecting with the USB terminal on the computer for using the supplied remote control as the computer mouse.

AUDIO output terminal

LAN terminal

Terminal for controlling the projector using a computer via network.

WIRED REMOTE terminal

For connecting the remote control to the projector when the signals from the remote control cannot reach the remote control sensor.

RS-232C terminal

Terminal for controlling the projector using a computer.

Remote control sensor

Exhaust vent

Carrying handle

Intake vent

* Kensington Security

Standard connector

AC socket

Connect the supplied power cord.

Using the Carrying Handle

When transporting the projector, carry it by the carrying handle on the side.

• Always put on the lens cap to prevent damage to the lens when transporting the projector.

• Do not lift or carry the projector by the lens or the lens cap as this may damage the lens.

* Using the Kensington Lock

• This projector has a Kensington Security Standard connector for use with a Kensington MicroSaver Security System. Refer to the information that came with the system for instructions on how to use it to secure the projector.

-13

Part Names and Functions

Remote Control

STANDBY button

For putting the projector into

standby mode.

KEYSTONE button

For entering the Keystone

Correction mode.

ENTER button

For setting items selected or

adjusted on the menu.

L-CLICK button

For the Left click when with the

USB connection (using a USB

cable or the optional

remote receiver).

MAGNIFY (Enlarge/Reduce)

buttons

For enlarging/reducing part of the

PAGE Up/Down buttons

Same as the [Page Down] and

[Page Up] keys on a computer

keyboard, when with the USB

connection (using a USB cable or

the optional remote receiver).

BREAK TIMER button

For displaying the break timer.

AUTO SYNC button

For automatically adjusting images

when connected to a computer.

PICTURE MODE button

For switching the picture mode.

INPUT buttons

For switching to the respective

input modes.

image.

WIRED R/C JACK

For controlling the projector by connecting the remote control to the projector.

ON button

For turning the power on.

MENU button

For displaying adjustment and setting screens.

39·43

MOUSE/Adjustment buttons ('/"/\/|)

• For moving the computer cursor when with the USB connection (using a USB cable or the optional remote receiver).

• For selecting and adjusting onscreen items.

R-CLICK/RETURN button

• For the Right click when with the USB connection (using a USB cable or the optional remote receiver).

• For returning to the previous display.

Volume buttons

For adjusting the speaker sound level.

AV MUTE button

For temporarily displaying the black screen and turning off the sound.

FREEZE button

For freezing images.

RESIZE button

For switching the screen size (NORMAL, STRETCH, etc.).

ECO+QUIET button

For lowering the noise of the cooling fan and extending the lamp life.

Using the Remote Control with a Signal Cable

When the signals from the remote control cannot be reached due to the positioning of the projector, use a ø3.5 mm minijack cable to connect the remote control to the projector. Now you can control the projector with the remote control.

Projector

(Rear view)

To WIRED REMOTE terminal

ø3.5 mm minijack cable (commercially available or available as Sharp service part QCNWGA038WJPZ)

To WIRED R/C JACK

Note

• The wireless remote function is not possible when the ø3.5 mm minijack cable is connected to the projector. Should the wireless remote operation be required, the ø3.5 mm minijack cable should be disconnected from the projector.

-14

Remote control

Using the Remote Control

Introduction

Usable Range

The remote control can be used to control the projector within the ranges shown in the illustration.

Note

• The signal from the remote control can be reflected off a screen for easy operation. However, the effective distance of the signal may differ depending on the screen material.

When using the remote control:

• Ta ke care not to drop, expose to moisture or high temperature.

• The remote control may malfunction under a fluorescent lamp. In this case, move the projector away from the fluorescent lamp.

Inserting the Batteries

Pull down the tab on the cover and remove the cover towards the direction of the arrow.

Front View

Rear View

23' (7 m)

30°

Remote control

Remote control sensor

23' (7 m)

Remote control sensor

30°

Remote control signal transmitters

30°

Remote control

30°

Remote control signal transmitters

30°

2 Insert the included batteries.

• Insert the batteries making sure the polarities correctly match the and marks inside the battery compartment.

3 Insert the lower tab of the cover

into the opening, and lower the cover until it clicks in place.

Incorrect use of the batteries may cause them to leak or explode. Please follow the precautions below.

Caution

• Danger of explosion if battery is incorrectly replaced. Replace only with alkaline or manganese batteries.

• Insert the batteries making sure the polarities correctly match the

ment.

• Batteries of different types have different properties, therefore do not mix batteries of different types.

• Do not mix new and old batteries.

This may shorten the life of new batteries or may cause old batteries to leak.

• Remove the batteries from the remote control once they have run out, as leaving them in can cause them to leak. Battery fluid from leaked batteries is harmful to skin, therefore ensure you wipe them first and then remove them using a cloth.

• The batteries included with this projector may run down in a short period, depending on how they are kept. Be sure to replace them as soon as possible with new batteries.

• Remove the batteries from the remote control if you will not be using the remote control for a long time.

• Comply with the rules (ordinance) of each local government when disposing of worn-out batteries.

and marks inside the battery compart-

-15

Quick Start

This section shows the basic operation (projector connecting with the computer). For details, see the page described below for each step.

Setup and Projection

In this section, connection of the projector and the computer is explained using one example.

37 STANDBY/ON button

6 INPUT buttons

6 ENTER button

5 Zoom knob

5 Focus ring

4 Tilt dial

4 Height Adjustment buttons

1. Place the projector facing a screen

7 STANDBY

button

3 ON button

6 COMPUTER 1

button

Page 18

2. Connect the projector to the computer and plug the power

cord into the AC socket of the projector

When connecting equipment other than the computer, see pages 25, 28 and 29.

Pages 23, 30

3. Remove the lens cap and turn the projector on

On the remote controlOn the projector

Page 30

-16

4. Adjust the angle

Adjust the projector angle

••

•

Adjust the projector angle using the Height

••

Adjustment buttons.

••

•

Rotate the Tilt dial to adjust the horizontal tilt of

••

the projector.

Height Adjustment buttons

Tilt dial

5. Adjust the focus and the zoom

••

•

This projector is equipped with an “Auto V-Keystone

••

Correction” function that automatically corrects any trapezoidal distortion within the projected image.

Pages 31, 32

Quick Start

Bring the projected image into focus

••

• Bring the projected image into focus by

••

rotating the focus ring.

Focus ring

Adjust the projected image size

••

• Adjust the projected image size by moving the

••

zoom knob.

Zoom out

Zoom knob

Zoom in

Page 33

6. Select the INPUT mode

Select the “COMPUTER 1” using the INPUT buttons on the projector or the COMPUTER 1 button on the remote control.

On the

projector

On the remote

control

••

•

When you press the INPUT buttons on the projector, the INPUT list appears.

••

Press

••

• When using the remote control, press COMPUTER1/2, DVI, S-VIDEO or VIDEO to

••

switch the INPUT mode.

" to select an item on the list, and press ENTER to switch to the selected INPUT mode.

" INPUT list

INPUT

COMPUTER1

COMPUTER2

DVI-D Computer

" On-screen Display (RGB)

COMPUTER1

RGB 1024 × 768

Page 34

7. Turn the Power off

Press the STANDBY button, then press that button again while the confirmation message is displayed, to put the projector into standby mode.

" On-screen Display

On the remote controlOn the projector

••

• Even if you unplug the power cord from the AC outlet, the cooling fan continues to run for a while.

••

Page 30

-17

Setting Up the Projector

For optimal image quality, position the projector perpendicular to the screen with the projector’s feet flat and level. Doing so will eliminate the need for Keystone correction and provide the best image quality. (See page 32.)

Standard Setup (Front Projection)

■ Place the projector at the required distance from the screen according to the desired picture size. (For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM.)

Example of standard setup

Side View

Base line:

Screen

Horizontal line passing through the lens center

L: Projection distance

Ceiling-mount Setup

■ It is recommended that you use the optional Sharp ceiling-mount adaptor and unit for this installation. Before mounting the projector, contact your nearest Sharp Authorized Projector Dealer or Service Center to obtain the recommended ceiling-mount adaptor and unit (sold separately).

Lens center

-18

Projection (PRJ) Mode

The projector can use any of the 4 projection modes, shown in the diagram below. Select the mode most appropriate for the projection setting in use. (You can set the PRJ mode in “SCR-ADJ” menu. See page 50.)

■ Ta ble mounted, front projection ■ Ceiling mounted, front projection [Menu item ➞ “Front”] [Menu item ➞ “Ceiling + Front”]

■ Ta ble mounted, rear projection ■ Ceiling mounted, rear projection

(with a translucent screen) (with a translucent screen)

[Menu item ➞ “Rear”] [Menu item ➞ “Ceiling + Rear”]

Setup

Indication of the Projection Image Size and Projection Distance

For details, refer to the “SETUP MANUAL” contained on the supplied CD-ROM. Example: 16:10 Signal Input (Normal Mode) for standard lens

Picture Size

500"

200"

100"

80"

40"

34"

85"

53"

68"

42"

21"

"–

4'11

(1.5 m – 1.8 m)

170"

5'11

9'10

"–

(3.0 m

106"

11'10

–

3.6 m)

"–

12'4

(3.8 m

424"×265"

14'9

4.5 m)

–

"–

24'8

(7.5 m

29'7

–

9.0 m)

61'7

73'11

–

(18.8 m – 22.5 m)

Projection Distance

-19

Setting Up the Projector

Picture (Screen) size Projection distance [L]

Diag. [x] Width Height Minimum [L1] Maxmum [L2]

400'' (1016 cm) 813 cm (320'') 610 cm (240'') 17.0 m (55' 9") 20.4 m (66' 11")

–15 cm

(

–5

/32")

300'' (762 cm) 610 cm (240'') 457 cm (180'') 12.8 m (41' 10") 15.3 m (50' 3")

–11 cm

(

–4

/64")

250'' (635 cm) 508 cm (200'') 381 cm (150'') 10.6 m (34' 10") 12.8 m (41' 10")

–9 cm

(

–3

/64")

200'' (508 cm) 406 cm (160'') 305 cm (120'') 8.5 m (27' 11") 10.2 m (33' 6")

–7 cm

(

–2

/64")

150'' (381 cm) 305 cm (120'') 229 cm (90'') 6.4 m (20' 11") 7.7 m (25' 1")

–5 cm

(

–2

/64")

120'' (305 cm) 244 cm (96'') 183 cm (72'') 5.1 m (16' 9") 6.1 m (20' 1")

–4 cm

(

–1

/32")

100'' (254 cm) 203 cm (80'') 152 cm (60'') 4.3 m (13' 11") 5.1 m (16' 9")

–4 cm

(

–1

/16")

80'' (203 cm) 163 cm (64'') 122 cm (48'') 3.4 m (11' 2") 4.1 m (13' 5")

–3 cm

(

–1

/64")

70'' (178 cm) 142 cm (56'') 107 cm (42'') 3.0 m (9' 9") 3.6 m (11' 9")

–3 cm

(

–1")

60'' (152 cm) 122 cm (48'') 91 cm (36'') 2.6 m (8' 4") 3.1 m (10' 1")

–2 cm

(

–

/64")

40'' (102 cm) 81 cm (32'') 61 cm (24'') 1.7 m (5' 7") 2.0 m (6' 8")

–1 cm

(

–

/64")

Standard Zoom Lens

F1.7-F1.9, f=28.0-33.6 mm

16:10 Signal Input (Normal Mode)

Diag. [x] Width Height Minimum [L1] Maxmum [L2] 500'' (1270 cm) 1077 cm (424'') 673 cm (265'') 18.8 m (61' 7") 22.5 m (73' 11") 400'' (1016 cm) 862 cm (339'') 538 cm (212'') 15.0 m (49' 3") 18.0 m (59' 2") 300'' (762 cm) 646 cm (254'') 404 cm (159'') 11.3 m (37' 0") 13.5 m (44' 4") 250'' (635 cm) 538 cm (212'') 337 cm (132'') 9.4 m (30' 10") 11.3 m (37' 0") 200'' (508 cm) 431 cm (170'') 269 cm (106'') 7.5 m (24' 8") 9.0 m (29' 7") 150'' (381 cm) 323 cm (127'') 202 cm (79'') 5.6 m (18' 6") 6.8 m (22' 2") 120'' (305 cm) 258 cm (102'') 162 cm (64'') 4.5 m (14' 9") 5.4 m (17' 9") 100'' (254 cm) 215 cm (85'') 135 cm (53'') 3.8 m (12' 4") 4.5 m (14' 9")

80'' (203 cm) 172 cm (68'') 108 cm (42'') 3.0 m (9' 10") 3.6 m (11' 10") 60'' (152 cm) 129 cm (51'') 81 cm (32'') 2.3 m (7' 5") 2.7 m (8' 10") 40'' (102 cm) 86 cm (34'') 54 cm (21'') 1.5 m (4' 11") 1.8 m (5' 11")

: Picture size (diag.) (in/cm) L: Projection distance(m/ft) L1: Minimum projection distance (m/ft) L2: Maximum projection distance (m/ft) H: Distance from the lens center to the bottom of the image (cm/in)

Picture (Screen) size Projection distance [L]

Distance from the lens center

to the bottom of the image [H]

–16 cm (–6 –13 cm (–5 –10 cm (–3

–8 cm (–3 –6 cm (–2 –5 cm (–1 –4 cm (–1 –3 cm (–1 –3 cm (–1 –2 cm (– –1 cm (–

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.03755 L2 (m) = 0.04507 H (cm) = –0.03209

[Feet/inches]

L1 (ft) = 0.03755χ / 0.3048 L2 (ft) = 0.04507 H (in) = –0.03209χ / 2.54

χ χ

/ 0.3048

/16") /64")

/64")

/32")

/32") /64") /64") /64")

/64")

/2")

4:3 Signal Input (Normal Mode)

Note

• Allow a margin of error in the value in the diagrams above.

• When the distance from the lens center to the bottom of the image [H] is a negative number, this indicates

that the bottom of the image is below the lens center.

• See page 18 about projection distance [L] and distance from the lens center to the bottom of the image [H].

-20

Distance from the lens center

to the bottom of the image [H]

The formula for picture size and projection distance

[m/cm]

L1 (m) = 0.04251 L2 (m) = 0.05102 H (cm) = –0.03633

[Feet/inches]

L1 (ft) = 0.04251 L2 (ft) = 0.05102χ / 0.3048 H (in) = –0.03633χ / 2.54

χ χ

/ 0.3048

Samples of Cables for Connection

•For more details of connection and cables, refer to the operation manual of the connecting equipment.

•You may need other cables or connectors not listed below.

Equipment

Computer

Audio-visual equipment

Terminal on

connected equipment

RGB cable (supplied)

RGB

output

terminal

DVI digital

video

output

terminal

Audio

output

terminal

DVI digital

video

output

terminal

Component

video

output

terminal

DVI Digital cable (commercially available)

ø3.5 mm stereo or mono audio cable (commercially available or available as Sharp service part QCNWGA038WJPZ)

DVI Digital cable (commercially available)

3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)

Cable

Terminal on the

projector

COMPUTER/ COMPONENT 1, 2

DVI-D

AUDIO

(for COMPUTER/ COMPONENT 1, 2, DVI-D)

DVI-D

COMPUTER/ COMPONENT 1, 2

Connections

Terminal

for using

the

dedicated

cable

S-video

output

terminal

Video output

terminal

Connect with the cable adaptor, etc.

Cable adaptor (commercially available)

Dedicated cable

S-video cable (commercially available)

Video cable (commercially available)

3 RCA to 15-pin D-sub cable (optional: AN-C3CP2)

S-VIDEO

VIDEO

-21

Samples of Cables for Connection

Equipment

Audio-visual equipment

Terminal on

connected equipment

ø3.5 mm stereo minijack to RCA audio cable

Audio

(commercially available)

output

terminal

Terminal

Connect with the cable adaptor, etc.

for using

the

dedicated

cable

Dedicated cable

RCA audio cable (commercially available) Audio output

terminal

Terminal

Connect with the cable adaptor, etc.

for using

the

dedicated

cable

Dedicated cable

Cable

Cable adaptor (commercially available)

ø3.5 mm stereo minijack to RCA audio cable (commercially available)

Cable adaptor (commercially available)

Terminal on the

projector

AUDIO

(for COMPUTER/ COMPONENT 1, 2, DVI-D)

AUDIO (for VIDEO, S-VIDEO)

Monitor

Amplifier

-22

RGB

input

terminal

Audio

input

terminal

RCA audio cable (commercially available)

RGB cable (supplied or commercially available)

ø3.5 mm stereo minijack to RCA audio cable

(commercially available)

MONITOR OUTPUT

AUDIO

(MONITOR OUT)

Connecting to a Computer

Before connecting, ensure the power cord of the projector from the AC outlet is unplugged, and that the devices to be connected are turned off. After making all connections, turn on the projector and then the other devices. When connecting a computer, ensure that it is the last device to be turned on after all the connections are made.

Ensure the operation manuals of the devices to be connected have been read before making connections.

When connecting with the RGB cable

(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)

Supplied

accessory

Computer

To audio output terminal

To RGB output terminal

RGB cable

ø3.5 mm stereo or mono audio cable

(commercially available or available as Sharp service part QCNWGA038WJPZ)

When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.

To COMPUTER/ COMPONENT 1 input terminal

To AUDIO input terminal

RGB cable

Connections

Note

• See page 65 “Computer Compatibility Chart” for a list of computer signals compatible with the projector. Use with computer signals other than those listed may cause some of the functions to not work.

• A Macintosh adaptor may be required for use with some Macintosh computers. Contact your nearest Macintosh Dealer.

• Depending on the computer you are using, an image may not be projected unless the computer’s external output port is switched on. (e.g. Press “Fn” and “F5” keys simultaneously when using a SHARP notebook computer). Refer to the specific instructions in your computer’s operation manual to

enable your computer’s external output port.

-23

Connecting to a Computer

When connecting with a DVI digital cable

The projector employs the DVI digital input terminal for direct input of Digital Video signals from a computer.

Computer

To AUDIO input terminal

To DVI digital output terminal

To audio output terminal

When using the ø3.5 mm mono audio cable, the volume level will be half of when using the ø3.5 mm stereo audio cable.

(for DVI-D)

DVI Digital cable (commercially available)

* ø3.5 mm stereo or mono audio cable

(commercially available or available as Sharp service part QCNWGA038WJPZ)

To DVI-D input terminal

-24

Connecting to Video Equipment

The image quality is highest in order of the Component signal, the RGB signal, the S-video signal and the Video signal. If your audio-visual equipment has a component output terminal or RGB output terminal, use the COMPUTER/COMPONENT terminal 1 or 2 on the projector for video connection.

When connecting video equipment with a DVI output terminal

Video Equipment

To audio output terminals

To DVI output terminal

To AUDIO input terminal (for COMPUTER/COMPONENT 2, DVI-D)

ø3.5 mm stereo minijack to RCA audio cable (commercially available)

DVI Digital cable (commercially available)

To DVI-D input terminal

Note

• Select the input signal type of the video equipment. See page 47.

• While the projector is connected to video equipment that has an HDMI output terminal, only the video

signal can be input to the projector. (Connect the AUDIO input terminal for audio input.)

• Depending on specifications of video equipment or HDMI to DVI digital cable, the signal transmission may not work property. (The HDMI specification does not support all connections to video equipment that has HDMI digital output terminal using HDMI to DVI digital cable.)

• For details on compatibility for connection, see support information on DVI connection provided by the video equipment manufacturer.

When connecting video equipment with component video output terminal

(Connecting to COMPUTER/COMPONENT 1 or 2: The illustration shown below is for the former.)

Video Equipment

To audio output terminal

To component video output terminal

To COMPUTER/COMPONENT 1 input terminal

To AUDIO input terminal

Connections

3 RCA (Component) to 15-pin D-sub cable (optional: AN-C3CP2)

ø3.5 mm minijack to RCA audio cable (commercially available)

Note

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a commercially available cable that fits in the projector terminal you want to connect.

• The projector does not support RGBC signals via the Euro-scart.

-25

Connecting to Video Equipment

When connecting video equipment with S-video output terminal

To audio output terminal

To S-video output terminal

Video Equipment

To S-VIDEO input terminal

To AUDIO input terminal

RCA audio cable (commercially available)

S-video cable (commercially available)

When connecting video equipment with video output terminal

To audio output terminal

To video output terminal

Video Equipment

RCA audio cable (commercially available)

Composite video cable (commercially available)

To VIDEO input terminal

To AUDIO input terminal

Note

• When you connect video equipment with a 21-pin RGB output (Euro-scart) to the projector, use a commercially available cable that fits in the projector terminal you want to connect.

-26

Controlling the Projector by a Computer

When the RS-232C terminal on the projector is connected to a computer, the computer can be used to control the projector and check the status of the projector. Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for “RS-232C Specifications and Commands”.

When connecting to a computer using an RS-232C serial control cable and a DIN-D-sub RS-232C adaptor

DIN-D-sub RS232C adaptor

Computer

To RS-232C terminal

RS-232C serial control cable (cross type, commercially available)

Supplied

accessory

To RS-232C terminal

DIN-D-sub RS-232C adaptor

Note

• The RS-232C function may not operate if your computer terminal is not correctly set up. Refer to the operation manual of the computer for details.

Connections

Info

• Do not connect the RS-232C cable to a port other than the RS-232C terminal on the computer. This may damage your computer or projector.

• Do not connect or disconnect an RS-232C serial control cable to or from the computer while it is on. This may damage your computer.

-27

Controlling the Projector by a Computer

When connecting to the LAN terminal using a LAN cable

TX/RX LED (yellow) Illuminates when transmitting/receiving data. LINK LED (green) Illuminates when linked.

HUB

Computer

*To ensure safety, do not connect the

LAN terminal with any cables such as a telephone line that may cause

LAN cable (Category 5 type, commercially available)

To LAN terminal

excessive voltage.

Note

• When connecting to hub, use straight-through Category 5 (CAT.5) type cable (commercially available).

• When connecting to computer, use cross-over Category 5 (CAT.5) type cable (commercially available).

Connecting to a Monitor with RGB Input Terminal

You can display computer images on both the projector and a separate monitor using two sets of RGB cables.

Monitor

To RGB input terminal

RGB cable (commercially available)

Computer

To RGB output terminal

Supplied

accessory

To COMPUTER/ COMPONENT 1 input terminal

RGB cable

To MONITOR OUT terminal

-28

Connecting to an Amplifier or Other Audio Equipment

Audio signals input from equipment connected to each audio input terminal of the projector can be output to audio equipment.

Amplifier

To AUDIO output terminal (MONITOR OUT)

To audio input terminal

ø3.5 mm minijack to RCA audio cable (commercially available)

Note

• Tu rn off the power of both the projector and audio equipment when connecting.

• When turning off the power in the case of connecting an amplifier or other audio equipment, first turn off

the power of the amplifier and then turn off the power of the projector.

• By using external audio components, the volume can be amplified for better sound.

• For details on Variable Audio Output (VAO) and Fixed Audio Output (FAO), see page 52.

Connections

-29

Turning the Projector On/Off

Connecting the Power Cord

Plug the supplied power cord into the AC socket on the rear of the projector. Then plug into the AC outlet.

Turning the Projector On

Before performing the steps in this section, connect any equipment that you use with the projector. (See pages 23-29.)

Remove the lens cap and press STANDBY/ON on the projector or ON on the remote control.

• The power indicator illuminates green.

• After the lamp indicator illuminates, the projec-

tor is ready to start operation.

Note

• The lamp indicator illuminates or blinks, indicating the status of the lamp.

Green: The lamp is on. Blinking green: The lamp is warming up. Red:

The lamp is shut down abnormally or the lamp should be

•

• If the projector is put into standby mode and

• When System Lock is set, the keycode in-

replaced.

When switching on the projector, a slight flickering of the image may be experienced within the first minute after the lamp has been illuminated. This is normal operation as the lamp's control circuitry is stabilizing the lamp output characteristics. This does not indicate malfunction.

immediately turned on again, the lamp may take some time to illuminate.

put box appears. To cancel the keycode setting, input the keycode that you have already set. See page 52 for details.

Supplied accessory

AC socket

Power cord

To AC outlet

Info

• When “Auto Restart” is set to “On”:

•

English is the factory preset language. If you want to change the on-screen display to another language, change the language according to the procedure on page 50.

Power indicator

STANDBY/ON button

ON button

STANDBY button

Lamp indicator

Turning the Power Off

(Put-

ting the Projector into Standby Mode)

Press STANDBY/ON on the projector or STANDBY on the remote control, then press

that button again while the confirmation message is displayed, to put the projector into standby mode.

-30

▼On-screen Display

Info

•

Direct Power Off function:

You can unplug the power cord from the AC outlet even if the cooling fan is still running.

Image Projection

Using the Adjustment Feet

The height of the projector can be adjusted using the adjustment feet when the screen is located higher than the projector, the screen is inclined or when the installation site is slightly inclined. Install the projector so that it is as perpendicular to the screen as possible.

Press the Height Adjustment buttons.

• The adjustment feet come out.

Lift the projector to adjust its height and remove your hands from the tons

• The projector is adjustable up to approximately 9 degrees.

Height Adjustment

but-

Side View

Lens center

Adjustment foot

Top View

Height Adjustment button

3 Rotate the Tilt dial to finely ad-

just the horizontal tilt of the projector.

• The inclination is adjustable within approximately 2 degrees.

• When adjusting the height of the projector, trapezoidal distortion occurs. When “Auto V-Keystone” of the “SCRADJ” menu is set to “On” (see page 49), keystone correction functions automatically to correct trapezoidal distortion. When you want to adjust the automatically corrected image, use the manual keystone correction. (See page 32.)

Info

• Do not press the Height Adjustment button when the adjustment feet come out without firmly holding the projector.

• Do not hold the lens when lifting or lowering the projector.

• When lowering the projector, be careful not to get your fingers caught in the area between the adjustment foot and the projector.

Basic Operation

Tilt dial

-31

Image Projection

Note

Correcting Trapezoidal Distortion

KEYSTONE button

MOUSE/Adjustment buttons ('/"/\/|)

Auto V-Keystone Correction

When the image is projected either from the top or from the bottom towards the screen at an angle, the image becomes distorted trapezoidally. The function for correcting trapezoidal distortion is called Keystone Correction. This projector is equipped with an “Auto V-Keystone Correction” function that automatically corrects any trapezoidal distortion within the projected image. The correction is made automatically provided the vertical incline or decline is within ±12 degrees.

Note

• When not using the Auto V-Keystone Correction function, set “Auto V-Keystone” on the “SCR-ADJ” menu to “Off”.

Manual Keystone Correction

When you want to make fine adjustments after the Auto V-Keystone Correction function has been activated, or when you want to make corrections without using the Auto V-Keystone Correction function, you can make corrections manually using the following procedure.

Press KEYSTONE on the remote control to enter the Keystone Correction mode.

• You can also use KEYSTONE on the projector.

RETURN button

"On-screen Display (Keystone Correction mode)

H&V KEYSTONE H: 0 V: 0

END

TESTPATTERN

ADJUST

RESET

Vertical Keystone Correction (Adjustment with

' / "

)

Horizontal Keystone Correction (Adjustment with

\ / |

)

2 Press ' or " to parallelize the

left and right sides, or press \ or | to parallelize the upper and lower sides of the projected image.

• You can also adjust the Keystone Correction using the on the projector.

3 Press

• The on-screen display of the Keystone

• You can also use KEYSTONE on the

-32

KEYSTONE

Correction mode will disappear.

projector.

" and

| buttons

• Press RETURN to return to the default set- ting.

• Straight lines or the edges of images may appear jagged while adjusting the image. The Manual Keystone Correction can be

•

adjusted up to an angle of approximately ±50 degrees vertically and approximately ±30 degrees horizontally.

Adjusting the Lens

The image is focused and adjusted to the screen size using the focus ring or zoom knob on the projector.

1 The focus is adjusted by rotat-

ing the focus ring.

2 Zooming is adjusted by moving

the zoom knob.

Focus ring Zoom knob

Zoom out

Basic Operation

Zoom in

-33

Image Projection

Switching the Input Mode

Select the appropriate input mode for the connected equipment.

Press COMPUTER1/2, DVI, S-VIDEO or VIDEO on the remote control to select the input mode.

• When you press INPUT on the projector or DVI on the remote control, the INPUT list appears.

Press

" to switch the INPUT mode.

Adjusting the Volume

Press VOL +/– on the remote control or –\/ |+ on the projector to adjust the volume.

Note

• Pressing VOL–/–

• Pressing VOL+/

• When the projector is connected to exter-

nal equipment, the volume level of the external equipment changes in accordance with the volume level of the projector. Set the projector’s volume to the lowest level when turning the projector on/off or when changing the input signal.

• When you do not want to output the sound from the projector’s speaker while the projector is connected to external equipment, set “Speaker” in “PRJ-ADJ” menu to “Off”. (See page 51.)

\ will lower the volume.

|+ will raise the volume.

VOL +/– (Volume) buttons

AV MUTE buttons

COMPUTER 1, COMPUTER 2, DVI, S-VIDEO, VIDEO buttons

On-screen display

Displaying the Black Screen and Turning off the Sound Temporarily

Press AV MUTE on the remote control to temporarily display a black screen and turn off the sound.

Note

• Pressing AV MUTE again will turn the pro- jected image back on.

-34

On-screen display

MOUSE/Adjustment buttons ('/"/\/|)

BREAK TIMER button

AUTO SYNC button

FREEZE button

ECO+QUIET button

Displaying and Setting the Break Timer

1 Press BREAK TIMER.

• The timer starts to count down from 5 minutes.

On-screen display

Switching the Eco+Quiet Mode

Press ECO+QUIET to switch the Eco+Quiet mode between on and off.

• When the Eco+Quiet Mode is set to “ON”, the sound of the cooling fan will turn down, the power consumption will decrease, and the lamp life will extend.

Note

• Refer to “Checking the Lamp Life Status” on

page 53 for details of the Eco+Quiet mode.

Auto Sync (Auto Sync Adjustment)

Auto Sync function works when detecting input signal after the projector turns on.

Press AUTO SYNC to manually adjust with Auto Sync function.

2 Press '/"/\/| to adjust the length

of the break time.

• Increases with ' or |

5 minutes s 6 minutes s 60 minutes

• Shortens with \ or "

4 minutes s 3 minutes s 1 minute

• The break time can be set in units of one minute (up to 60 minutes).

Canceling the break timer display function

Press BREAK TIMER.

Note

• Break Timer does not function while the projector is operating the “Auto Sync”, “FREEZE” or “AV MUTE” functions.

Note

• When the optimum image cannot be achieved with Auto Sync adjustment, use manual adjustments. (See page 47.)

Freezing a Moving Image

1 Press FREEZE.

• The projected image is frozen.

2 Press FREEZE again to return to

the moving image from the currently connected device.

Basic Operation

-35

Note

Image Projection

MOUSE/Adjustment buttons ('/"/\/|)

MAGNIFY buttons

RETURN button

Displaying an Enlarged Portion of an Image

Graphs, tables and other portions of projected images can be enlarged. This is helpful when

providing more detailed explanations.

PICTURE MODE button

Selecting the Picture Mode

You can select the appropriate picture mode for the projected image, such as movie or video game.

Press PICTURE MODE.

• When pressing PICTURE MODE, the picture mode changes in the following order:

STANDARD PRESENTATION MOVIE GAME sRGB

Note

• See page 45 for details on the picture mode.

* “sRGB” is displayed only when RGB signal is input.

1 Press MAGNIFY on the remote

control.

• Enlarges the image.

• Pressing

reduces the projected image.

×1 ×2 ×3 ×4 ×9

• You can change the location of the enlarged image using

or MAGNIFY enlarges or

Press

\ and

2 Press RETURN on the remote con-

trol to cancel the operation.

• The magnification then returns to ×1.

• The selectable magnifications differ de-

pending on the input signal.

• In the following cases, the image will return to the normal size (×1).

- When switching the INPUT mode.

- When RETURN has been pressed.

- When the input signal is changed.

-When the input signal resolution and re-

fresh rate (vertical frequency) change.

- When the Resize mode is changed.

- When the Picture mode is changed.

- When the Progressive mode is changed.

-36

Resize Mode

This function allows you to modify or customize the resize mode to enhance the input image. Depending on the input signal, you can choose a desired image.

Press RESIZE.

• See page 49 for setting on menu screen.

COMPUTER

NORMAL

1068 × 800

1000 × 800

1280 × 720

1280 × 722

1280 × 720

1280 × 768

1280 × 800

NORMAL FULL

4:3 aspect ratio

Other aspect ratios

Computer

Resolution

XGA and below

Resolution

higher than

XGA

SVGA (800 × 600)

XGA (1024 × 768)

SXGA (1152 × 864)

SXGA+ (1400 × 1050)

SXGA (1280 × 1024)

1280 × 720

1360 × 768

1366 × 768

1280 × 768

1280 × 800

Input signal

Image Type

4:3 aspect ratio

FULL STRETCHDOT BY DOT

1280 × 800

—

800 × 600

1024 × 768

1152 × 864

1400 × 1050

1280 × 1024

1360 × 768

1366 × 768

Output screen image

DOT BY DOT

RESIZE button

1280 × 720

—

1280 × 720

STRETCH

Basic Operation

SXGA

(1280 ´ 1024)

5:4 aspect ratio

1280 ´ 720

16:9 aspect ratio

1360 ´ 768 1366 ´ 768

16:9 aspect ratio

1280 ´ 768

15:9 aspect ratio

1280 ´ 800

16:10 aspect ratio

: Cutout area on which images cannot be projected : Area where the signals are off screen

*1 The Image Shift function can be used for these images. *2 Same as NORMAL mode. *3 In case SXGA+ input.

*1*1

—

-37

Image Projection

VIDEO/DTV

Input signal

480I, 480P, 576I, 576P,

NTSC, PAL,

SECAM

720P, 1035I,

1080I, 1080P

Image Type NORMALVideo/DTV

4:3 aspect ratio

Squeeze

Letter box

16:9 aspect ratio

Output screen image

AREA ZOOM

V-STRETCH

STRETCH

—

16:9 aspect ratio

540P

16:9 aspect ratio

(4:3 aspect ratio in 16:9)

: Cutout area on which images cannot be projected : Area on which the image is not included in the original signals

The Image Shift function can be used for these images.

Same as NORMAL mode.

About Copyrights

• When using the RESIZE function to select an image size with a different aspect ratio to a TV program or video image, the image will look different from its original appearance. Keep this in mind while choosing an image size.

• The use of the Resize or Keystone Correction function to compress or stretch the image for commercial purposes/public displays in a café, hotel, etc. may be an infringement of copyright protected by law for copyright holders. Please use caution.

-38

Using the Remote Control as the Wireless Computer Mouse

When connecting the projector and the computer with a USB cable, you can use the remote control as the computer mouse. If the computer is placed too far away from the projector to be connected via the USB cable, the separately sold remote receiver (AN-MR2) makes it possible to operate the projector with the remote control. For de-

tails, see the operation manual of the receiver.

Connecting with a USB cable

Computer

USB terminal

To USB terminal

Point the remote control at

USB remote receiver

the (AN-MR2, optional)

USB cable (commercially available or available as Sharp service part QCNWGA014WJPZ)

The mouse pointer can be operated in the following way after it is connected.

MOUSE/Adjustment buttons ('/"/\/|)

■ When moving the cursor

Press MOUSE/Adjustment buttons ('/"/\/|).

■ When left-clicking

Press L-CLICK.

R-CLICK button

■ When right-clicking

Press R-CLICK.

■ When your computer supports only a one-click mouse (such as Macintosh)

PAGE Up/Down buttons

L-CLICK button

Press L-CLICK or R-CLICK.

L-CLICK and R-CLICK have common function.

■ When using [Page Up] or [Page Down]

Same as the [Page Up] and [Page Down] keys on a computer keyboard. Press PAGE UP or PAGE DOWN PAGE.

Note

• This function only works with the Microsoft® Windows® OS and Mac OS®. However, this function does not work with the following operation systems that do not support USB.

• Versions earlier than Windows® 95

• Versions earlier than Windows

• Versions earlier than Mac OS

• You cannot use this function when displaying the menu screen.

• Confirm that the computer recognizes the USB connection.

NT4.0

8.5

Basic Operation

-39

Menu Items

The following shows the items that can be set in the projector.

“Picture” menu

Main Menu

Picture

Page 45

Picture Mode

Page 45

Contrast

Bright

Color

Tint

Sharp

Red

Blue

Sub Menu

Standard Presentation Movie Game

sRGB

+30-30

Page 45

CLR Temp

Page 45

Progressive

Page 46

Film Mode

Page 46

DNR

Page 46

MNR

Page 46

Eco+Quiet Mode

Page 46

Reset

5500K 6500K 7500K 8500K 9300K 10500K

3D Progressive 2D Progressive

Auto Off

Off Level 1 Level 2 Level 3

On Off

Page 45

*1 Item when inputting RGB signal through COMPUTER/COMPONENT 1, 2 or DVI-D *2 Items when inputting Component signal through COMPUTER/COMPONENT 1 or 2, or when selecting VIDEO or

S-VIDEO

*3 “Progressive” and “Flim Mode” can be adjusted only when 480I, 576I, 1035I or 1080I signal is input.

-40

“Signal adjustment (SIG-ADJ)” menu

Main Menu

SIG-ADJ

Page 47

Clock

Phase

H-Pos

V-Pos

Reset

+150-150

+30-30

+150-150

+60-60

Page 47

Resolution

Page 47

Auto Sync

Page 47

Signal Type

Page 47

Dynamic Range

Page 48

Video System

Page 48

Signal Info

On Off

Auto RGB Component

Auto Standard Enhanced

Auto PAL SECAM NTSC4.43 NTSC3.58 PAL-M PAL-N PAL-60

Page 48

*4 Item when inputting RGB signal through COMPUTER/COMPONENT 1 or 2 *5 Item when inputting COMPUTER/COMPONENT 1 or 2 *6 Item when selecting COMPUTER/COMPONENT 1, 2 or DVI-D *7 Item when selecting DVI-D *8 Item when selecting VIDEO or S-VIDEO

“Screen adjustment (SCR-ADJ)” menu

Main Menu Sub Menu

SCR-ADJ

Page 49

Resize

Page 49

Image Shift

Page 49

H-Keystone

Page 49

V-Keystone

Page 49

Auto V-Keystone

Page 49

OSD Display

Page 50

Background

Page 50

Menu Position

Page 50

PRJ Mode

Page 50

Language

Page 50

Normal Full Dot By Dot Area Zoom V-Stretch

+40-40

Stretch

+60-60

+100-100

On Off

Logo Blue None

Center Upper Right Lower Right Upper Left Lower Left

Front Ceiling + Front Rear Ceiling + Rear

English

polski

Deutsch

Magyar

Español

Türkçe Nederlands Français Italiano Svenska Português

Useful Features

-41

Menu Items

“Projecter adjustment (PRJ-ADJ)” menu

Main Menu Sub Menu

PRJ-ADJ

Page 51

Auto Power Off

Page 51

Auto Restart

Page 51

System Sound

Page 51

Speaker

Page 51

Audio Out

Page 51

Monitor Out

Page 51

LAN/RS232C

Page 51

RS-232C

Page 52

Fan Mode

Page 52

System Lock

Pages 52 and 53

All Reset

On Off

FAO VAO

Enable Disable

9600 bps 38400 bps 115200 bps

Normal High

Old Code New Code Reconfirm

Page 53

Lamp Timer (Life)

Page 53

“Network” menu

Main Menu

Network

Page 54

Password

Page 54

DHCP Client

Page 55

TCP/IP

Page 55

MAC Address

Page 55

Projector

Page 55

Old Password New Password Reconfirm

On Off

IP Address Subnet Mask Gateway

*1 Adjustable only when DHCP Client is set to “Off” *2 Display only

-42

Using the Menu Screen

Adjustment buttons ('/"/\/|)

ENTER button

MOUSE/Adjustment buttons ('/"/\/|)

ENTER button

MENU button

RETURN button

Menu Selections (Adjustments)

Example: Adjusting “Bright”.

• This operation can also be performed by using the buttons on the projector.

1 Press MENU.

• The “Picture” menu screen for the selected input mode is displayed.

2 Press

ture” to adjust.

| or

\ and select “Pic-

Example: “Picture” screen menu

Picture SIG SCR PRJ Net.

Picture Mode

Contrast 0 Bright Color Tint

Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode

Reset

SEL./ADJ. RETURN

Menu item

0 0 0 0Sharp 0 0

MENU button

RETURN button

• Press RETURN to return to previous screen when the menu is displayed

Standard

7500K 3D Progressive Auto Off Off Off

ENTER END

Useful Features

-43

Using the Menu Screen

3 Press

' or

" and select

“Bright” to adjust.

• The selected item is highlighted.

To adjust the projected image while watching it

Press ENTER.

• The selected item (e.g. “Bright”) is displayed by itself at the bottom of the screen.

• When pressing item (“Red” after “Bright”) will be displayed.

Note

• Press ENTER again to return to the previous screen.

' or

", the following

Picture SIG SCR PRJ Net.

Picture Mode

Contrast 0

Bright

Color Tint

Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode

Reset

SEL./ADJ. RETURN

Standard

0 0 0Sharp 0 0

7500K 3D Progressive Auto Off Off Off

ENTER END

Items to be adjusted

Pict. SIG–ADJ SCR PRJ Net.

Clock 0 Phase H-Pos V-Pos

Reset

0 0 0

Press ENTER.

The item displayed by itself

Picture

SEL./ADJ. Rtn. Menu

0Bright

Rtn. Menu END

4 Press

\ or

| to adjust the item

selected.

• The adjustment is stored.

5 Press MENU.

• The menu screen will disappear.

Picture SIG SCR PRJ Net.

Picture Mode

Contrast 0

Bright

Color Tint

Red Blue CLR Temp Progressive Film Mode DNR MNR Eco+Quiet Mode

Reset

SEL./ADJ. RETURN

0 0 0Sharp 0 0

Standard

7500K 3D Progressive Auto Off Off Off

ENTER END

Note

• Menu buttons do not function while the projector is operating the “Auto Sync”, “Break Timer”, “FREEZE”, or “AV MUTE” functions.

-44

Picture Adjustment (“Picture” menu)

Picture SIG SCR PRJ Net.

Picture Mode

Contrast 0 Bright Color

Tint

Red Blue CLR Temp

Progressive

Film Mode

DNR

MNR

Eco+Quiet Mode

Reset

SEL./ADJ. RETURN

Selecting the Picture Mode

Selectable items

Standard Presentation

Movie

Game

*sRGB

Description

For standard image Brightens portions of image for more enhanced presentations. Gives natural tint to the projected image. Gives sharpness to the projected image. For high fidelity reproduction of images from a computer.

Standard

0 0 0 0Sharp 0 0

7500K 3D Progressive Auto Off Off Off

ENTER END

The default

settings of CLR Temp

7500K 7500K

6500K

7500K

–

• “sRGB” is displayed only when RGB signal is input.

• You can set or adjust each item in the “Picture”

menu to your preference. Any changes you make are retained in memory.

Menu operation

Adjusting the Image

Adjustment items Contrast Bright

Color

Tint

Sharp

Red

Blue

Not adjustable/selectable in the RGB input mode.

Not adjustable/selectable when selecting “sRGB”

button

For less contrast. For less brightness. For less color intensity. For making skin tones purplish. For less sharpness. For weaker red. For weaker blue.

For more contrast. For more brightness. For more color intensity. For making skin tones greenish. For more sharpness. For stronger red. For stronger blue.

Page 43

button

in “Picture Mode”.

Note

• “Red” and “Blue” cannot be set when selecting “sRGB” in “Picture Mode”.

• To reset all adjustment items, select “Reset” and press ENTER.

Adjusting the Color Temperature

Selectable items 5500K 6500K 7500K 8500K 9300K 10500K

For lower color temperature for warmer, reddish incandescent-like images.

For higher color temperature for cooler, bluish, fluorescent-like images.

Description

Note

• You can also press PICTURE MODE on the remote control to select the picture mode. (See page 36.)

• *sRGB is an international standard of color reproduction regulated by the IEC (International Electrotechnical Commission). As the fixed color area has been decided by the IEC, the images are displayed in a natural tint based on an original image, when “sRGB” is selected. For additional information about the sRGB function, visit “http://www.srgb.com/”. You cannot set the items, “Red”, “Blue” and “CLR Temp”, when “sRGB” is selected.

Info

• When “sRGB” is selected, the projected image may become dark, but this does not indicate a malfunction.

Note

• Values on “CLR Temp” are only for general standard purposes.

• “CLR Temp” cannot be set when selecting “sRGB” in “Picture Mode”.

Useful Features

-45

Picture Adjustment (“Picture” menu)

Selecting the Progressive Mode

Selectable items

3D Progressive

2D Progressive

Note

• When the image is blurred or noisy, switch to the optimal mode.

• When using progressive inputs, inputs are directly displayed so that “2D Progressive” and “3D Progressive” cannot be selected.

Selecting the Film Mode

This function provides high-quality playback of images originally projected at 24 fps, such as movies on DVDs.

Selectable items

Auto Off

Useful to display relatively slowmoving images such as drama and documentary more clearly. Useful to display fast-moving images such as sports and action films.

Films are detected automatically. Films are not detected.

Description

Menu operation

Note

• Set a level so as to view a clearer picture.

Page 43

Make sure to set “DNR” to “Off” in the following cases:

• When the image is blurry.

• When the contours and colors of moving im-

ages drag.

• When TV broadcasts with weak signals are projected.

Info

• This function is available for all signals with VIDEO or S-VIDEO.

• This function is available for 480I, 480P, 576I and 576P signals with COMPUTER1/2 or DVI.

Mosquito Noise Reduction (MNR)

The so-called Mosquito Noise (flickering) can be reduced.

Selectable items Off Level 1-3

MNR does not function. Sets the MNR level for viewing a clearer picture.

Description

Note

• When using progressive inputs, “Film Mode” cannot be selected.

• The “Film Mode” function does not work when “2D Progressive” is selected in “Progressive Mode”.

Reducing Image Noise (DNR)

Video digital noise reduction (DNR) provides high quality images with minimal dot crawl and cross color noise.

Selectable items

Off Level 1–3

-46

DNR does not function. Sets the DNR level.

Description

Info

• This function is available for all signals with VIDEO or S-VIDEO.

• This function is available for 480I, 480P, 576I and 576P signals with COMPUTER1/2 or DVI.

Eco+Quiet Mode Setting

Selectable

items

Off

Note

• You can also use ECO+QUIET on the remote control or on the projector to switch the Eco+Quiet Mode. (See page 35.)

Brightness

Approx. 80%

100%

Fan

Sound

Low

Normal

Lamp life

Approx.

3,000 hours

Approx.

2,000 hours

Signal Adjustment (“SIG-ADJ” Menu)

Pict. SIG–ADJ SCR PRJ Net.

Clock Phase

H-Pos V-Pos

Reset

Resolution

Auto Sync

Signal Type

Dynamic Range

Video System

Adjusting the Computer Image

Signal Info : 800 x 600

H 60.3 kHz / V 37.8 Hz

SEL./ADJ. RETURN

0 0 0 0

640 x 480 On Auto Standard Auto

ENTER END

If the optimum image cannot be obtained with Auto Sync adjustment, use the SIG-ADJ function.

Selectable items Clock Phase

H-Pos

V-Po s

Adjusts vertical noise. Adjusts horizontal noise (similar to tracking on your VCR). Centers the on-screen image by moving it to the left or right. Centers the on-screen image by moving it up or down.

Description

Menu operation

Auto Sync Adjustment

Page 43

Used to automatically adjust a computer image.

Selectable items

Off

Auto Sync adjustment will occur when the projector is turned on or when the input signals are switched, when connected to a computer. Auto Sync adjustment is not automatically performed.

Description

Note

• Auto Sync adjustment is also performed by pressing AUTO SYNC on the projector or on the remote control.

• The Auto Sync adjustment may take some time to complete, depending on the image of the computer connected to the projector.

Signal Type Setting

This function allows you to select the input signal type RGB or Component for COMPUTER/ COMPONENT 1, 2 or DVI-D.

Note

• To reset all adjustment items, select “Reset” and press ENTER.

• The adjustable range of “H-Pos” (H-Position) and “V-Pos” (V-Position) may vary depending on the screen resolution of the computer.

Resolution Setting

Ordinarily, the type of input signal is detected and the correct resolution mode is automatically selected. However, for some signals, the optimal resolution mode in “Resolution” on the “SIG-ADJ” menu may need to be selected to match the computer display mode.

Note

• See “Checking the Input Signal” on page 48 for information on the currently selected input signal.

Selectable items Auto

RGB Component

Input signals are automatically recog-

Description

nized as RGB or component. Set when RGB signals are received. Set when Component signals are received.

Useful Features

-47

Signal Adjustment (“SIG-ADJ” Menu)

Selecting the Dynamic Range

An optimum picture may not be displayed if a DVI-D-capable device’s output signal type and the projector’s input signal type do not match. If this should occur, switch “Dynamic Range”.

Selectable items Auto Standard Enhanced

Note

• The Dynamic Range can be selected only when “DVI-D” input mode is selected.

Setting the Video System

The video input system mode is factory preset to “Auto”; however, a clear picture from the connected audio-visual equipment may not be received, depending on the Video signal difference. In that case, switch the Video signal.

* When reproducing NTSC signals in PAL video

equipment.

When the black levels of the image show banding or appear faded, select the item that results in the best picture quality. (In most circumstances, “Standard” should be selected.)

Selectable items Auto PA L SECAM *NTSC4.43 NTSC3.58 PAL-M PAL-N PAL -60

Description

Menu operation

Checking the Input Signal

This function allows you to check the current input signal information.

Page 43

Note

• The Video signal can only be set in VIDEO or S-VIDEO mode.

• When “Video System” is set to “Auto”, you may not receive a clear picture due to signal differences. Should this occur, switch to the video system of the source signal.

-48

Screen Adjustment (“SCR-ADJ” Menu)

Pict. SIG SCR-ADJ PRJ Net.

Resize

Image Shift

H-Keystone V-Keystone

Auto V-Keystone OSD Display

Background

Menu Position

PRJ Mode

Language

SEL./ADJ. RETURN

Setting the Resize Mode

Normal 0 0 0

Logo

Center

Front

English

ENTER END

Note

• For details of the Resize mode, see pages 37 and 38.

• You can also press RESIZE on the remote con- trol to set the resize mode. (See page 37.)

Menu operation

Keystone Correction

Page 43

Auto V-Keystone Correction

Set “Auto V-Keystone” on the “SCR-ADJ” screen menu to “On”.

Manual Keystone Correction

Set “Auto V-Keystone” on the “SCR-ADJ” screen menu to “Off”. Select “V-Keystone”, and then

press

\ or

| to parallelize the left and right sides

of the projected image with the slide bar. To parallelize the upper and lower sides, select “H-

Keystone” and press

\ or

Ver tical Keystone Correction

Adjusting the Image Position

You can move the projected image vertically.

\ \

\ button

\ \

| button

Note

• This function only works in some RESIZE modes. (See pages 37 and 38.)

• To reset this function, select “0”.

Horizontal Keystone Correction

Note

•

The Keystone Correction can be adjusted up to an angle of approximately ±12 degrees with “Auto V-Keystone” and up to an angle of approximately ±50 degrees with “V-Keystone” and approximately ±30 degrees with “H-Keystone”.

• When the screen is slanting or the image is deteriorated, set “Auto V-Keystone” to “Off”.

Useful Features

-49

Screen Adjustment (“SCR-ADJ” Menu)

Setting the On-screen Display

This function allows you to turn the on-screen messages on or off.

Selectable items

Off

Selecting a Startup and

All On-screen Displays are displayed.

INPUT/VOLUME/AV MUTE/FREEZE/ AUTO SYNC/MAGNIFY/ “An invalid button has been pressed.” are not displayed.

Description

Background Image

Selectable items Logo

Blue None

Selecting the Menu

SHARP default image

Blue screen

Black screen

Description

Screen Position

Select “Menu Position” on the “SCR-ADJ” menu and the desired position for the menu screen.

Selectable items Center Upper Right Lower Right Upper Left Lower Left

Displayed on the center of the image. Displayed on the upper right of the image. Displayed on the lower right of the image. Displayed on the upper left of the image. Displayed on the lower left of the image.

Description

Menu operation

Reversing/Inverting Pro-

Page 43

jected Images

This projector is equipped with a reverse/invert image function that allows you to reverse or invert the projected image for various applications.

Selectable items

Front

Ceiling + Front

Rear

Ceiling + Rear

Note

• This function is used for the reversed image and ceiling-mount setups. (See page 19.)

Selecting the On-screen

Normal image (Projected from the front of the screen)

Inverted image (Projected from the front of the screen with an inverted projector)

Reversed image (Projected from the rear of the screen or with a mirror)

Reversed and inverted image (Projected with a mirror)

Description

Display Language

The projector can switch the on-screen display language among 17 languages.

-50

Helpful Functions Set during Installation (“PRJ-ADJ” menu)

Pict. SIG SCR PRJ-ADJ Net.

Auto Power Off

Auto Restart

System Sound

Speaker

Audio Out

Monitor Out

LAN/RS232C

RS-232C

Fan Mode

System Lock

All reset

Lamp Timer (Life) [ 0]h [ 0] min ( 100%)

SEL./ADJ. RETURN

Auto Power Off Function

Selectable items On

Off

The projector automatically enters the standby mode when no input signal is detected for 15 minutes or longer. The Auto Power Off function will be disabled.

On On On FAO Enable Enable 9600bps Normal Disable

ENTER END

Description

Note

• When the Auto Power Off function is set to “On”, 5 minutes before the projector enters the standby mode, the message “Enter STANDBY mode in X min.” will appear on the screen to indicate the remaining minutes.

Speaker Setting

Menu operation

Page 43

This function allows you to set the audio output of the internal speaker to “On” or “Off” such as when the projector is connected to an external amplifier.

Selectable items

Off

The audio signal is output from the internal speaker. The audio signal is not output from the internal speaker.

Audio Output Type Setting

Description

This function determines whether the audio level output from the AUDIO output (MONITOR output) terminal is fixed or variable by linking with VOLUME.

Selectable items FAO (Fixed Audio Output) VAO (Variable Audio Output)

Audio output that does not vary in strength with the volume level of the source projector. Audio output that varies in strength with the volume level of the source projector.

Description

Info

• When “Audio Out” has been set to “VAO”, first make sure to lower the volume of the projector before turning the power on or off and when switching the input.

2 Auto Restart Function

Selectable items On

Off

Setting the Confirmation

If the power cord is unplugged from the outlet or the breaker switch is turned off when the projector is on, then the projector automatically turns on when the power cord is plugged into the AC outlet or the breaker switch is turned on. The projector does not turn on automatically when the power cord is plugged into the AC outlet or the breaker switch is turned on.

Description

Sound (System Sound)

Selectable items On

Off

A confirmation sound is made when the projector turns on/off. No confirmation sound is made.

Description

Monitor Output

LAN/RS232C

When set to “Enable”, the function is activated and power is consumed even in the standby mode. It is recommended that the function be set to “Disable” when it is not connected. This reduces power consumption when the projector is in the standby mode.

Selectable items Enable

Disable

The function is activated even if the projector is in standby mode. The function is switched off when the projector is in standby mode.

Description

Note

• When you want to control the projector using the LAN/RS232C function, select “Enable”.

Useful Features

-51

Helpful Functions Set during Installation (“PRJ-ADJ” menu)

Note

Selecting the Transmission Speed (RS-232C)

Make sure that both the projector and computer are set for the same baud rate.

Selectable items 9600 bps

38400 bps

115200 bps

Note

• Refer to the “SETUP MANUAL” contained on the supplied CD-ROM for RS-232C Specifications and Command Settings.

• Refer to the computer’s operation manual for instructions for setting the computer’s baud rate.

Fan Mode Setting

This function changes the fan rotation speed.

Selectable items Normal High

When “Fan Mode” is set to “High”, the fan rotation speeds up, and the fan noise becomes louder.

System Lock Function

This function prevents unauthorized use of the projector. Once this function is activated, users must enter the correct keycode each time the projector is turned on. We suggest you record the

keycode in a safe place where only authorized users have access.

Info

• If you lose or forget your keycode, contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 68). Even if the product warranty is valid, the keycode reset will incur a charge.

Tr ansmission speed is slow.

Tr ansmission speed is rapid.

Suitable for normal environments. Select this when using the projector at altitudes of approximately 1,500 meters (4,900 feet) or more.

Description

Menu operation

Page 43

Setting/Changing the keycode

1 Select “System Lock”, then press

ENTER or

2 Select “Next”, then press ENTER.

• The screen for entering the keycode appears.

3 Press the 4 buttons on the remote

control or on the projector to enter the preset keycode in “Old Code”.

• When setting the keycode for the first time,

press " on the projector for four times.

PRJ-ADJ

Setting the System Lock

Old Code

New Code Reconfirm

• If you input a wrong keycode, the cursor returns to the first point of the “Old Code”.

• The preset keycode is 4 " buttons on the projector. When you press the " button four times, the keycord input screen disappears.

––––

–––– ––––

4 Press the 4 buttons on the remote

control or on the projector to enter the new keycode in “New Code”.

• You cannot use the following buttons for keycode: STANDBY/ON, ON, STANDBY,

ENTER, L-CLICK, R-CLICK/RETURN, MENU, ECO+QUIET and BREAK TIMER

• System lock function recognizes each button on the remote control or on the projector as an individual button, even if they share the same button name. If you used the buttons on the projector in setting your keycode, the keycode cannot be canceled with the remote control.

PRJ-ADJ

Setting the System Lock

-52

Old Code

New Code

Reconfirm

****

–––

– ––––

Enter the same keycode in “Re-confirm”.

Note

To cancel the keycode that you have already set

• Press " on the projector for four times in steps

4 and 5 above.

When the System Lock is set

• When System Lock is set, the keycode input screen appears after the power is turned on. When it appears, enter the right keycode to start projection.

Input screen for keycode

System Lock

––––

Menu operation

Returning to the Default

Page 43

Settings

This function allows you to initialize the settings you have made in the projector.

Note

The following items or menu cannot be initialized.

• “SIG-ADJ” menu Resolution

• “SCR-ADJ” menu Language

• “PRJ-ADJ” menu Lamp Timer (Life) System Lock

Keylock Function

Locking the Operation Buttons on the Projector

Use this function to lock the operation buttons on the projector.

■ Locking the Operation Buttons

Hold down ENTER on the projector for about 5 seconds while the projector is being turned on.

▼On-screen Display

Keylock function ON

• The keylock function does not affect the operation with the remote control buttons.

• You cannot use the keylock function while the projector is warming up.

■ Taking the Keylock off

Hold down ENTER on the projector for about 5 seconds.

▼On-screen Display

Keylock function OFF

• When the projector is in standby mode, you can release the keylock by holding down ENTER and STANDBY/ON on the projector simultaneously for about 5 seconds.

w Checking the Lamp Life

Status

You can confirm the cumulative lamp usage time and the remaining lamp life (percentage).

Lamp usage condition

“Life” Operated exclusively while “Eco+Quiet Mode” is “On”. Operated exclusively while “Eco+Quiet Mode” is “Off”.

Note

• It is recommended that the lamp be changed when the remaining lamp life becomes 5%.

• Remaining lamp life changes within the range of the values shown depending on the frequency at which “Eco+Quiet Mode” is switched to “On”

and “Off”. (See page 46.)

• The lamp life may vary depending on the usage condition.

Remaining lamp life

100% 5%

Approx. Approx. 3,000 hours 150 hours

Approx. Approx.

2,000 hours 100 hours

Useful Features

Info

• Keylock cannot be set while the projector is: displaying the “Menu” screens, in standby mode, warming up, changing input signals, operating “Auto Sync” function or on the “System Lock” screen during warming up.

-53

Setting up the Projector Network Environment (“Network” menu)

Pict. SIG SCR PRJ Network

Password

DHCP Client

TCP/IP

MAC Address XX:XX:XX:XX:XX:XX

Projector XX-XXXX

SEL./ADJ. RETURN

Setting a Password

If you do not want others to change the setting for the “Network” menu, set a password.

Disable

Off

ENTER END

Setting a Password

1 Select “Password”, then press

• The screen for entering the password appears.

Network

Setting the Password

Old Password

New Password

Reconfirm

––––

–

–––

––––

Menu operation

Page 43

Changing the Password

1 Select “Password”, then press

• The screen for entering the password appears.

2 Enter the password in “Old Pass-

word” using

| and

\, then

press ENTER.

3 Enter the password in “New Pass-

word” using

| and

\, then

press ENTER.

4 Enter the same password again in

“Reconfirm” using

| and

then press ENTER.

Note

• If you do not need the password protection for the “Network” menu settings anymore, press ENTER without entering new password in steps 3 and 4.

•To cancel the password settings, press RETURN.

2 Press

“New Password”, then press

' or

" to set the first digit in

3 Enter the remaining 3 digits, then

press ENTER.

• To return to the previous digit, press \.

4 Enter the same password in

“Reconfirm”, then press ENTER.

• The status for “Password” changes to “Enable”.

Note

• Once after the password is set, you must enter the password to change the “Network” menu settings.

-54

If you forget the password

If you forget the password, perform the following procedure to delete it, then set a new password.

On the projector, press

Note

•

If ENTER is held down for more than 5 seconds, the operation buttons on the projector will be locked. (See page 53.)

•

You cannot use the buttons on the remote control to delete the password.

DHCP Client Setting

Connect the LAN cable before turning the projector on. If not, the DHCP Client function does not work.

Selectable items On

Off

Select “On” for “DHCP Client”. “Obtaining IP Address...” appears, then the menu screen appears. Confirm the parameters of IP Address, Subnet Mask and Gateway on the TCP/IP screen. If the DHCP server is not available, “Could not obtain IP Address.” appears. In this case, set the TCP/IP manually. (See the item

3.)

TCP/IP Setting

Set the TCP/IP manually.

Obtains configuration parameters for TCP/IP network automatically. Sets the TCP/IP manually.

Description

1 Select “Off” for “DHCP Client”, then

press ENTER.

Menu operation

Selectable items IP Address

Subnet Mask

Gateway

Note

• Confirm the existing network’s segment (IP address group) to avoid setting an IP address that duplicates the IP addresses of other network equipment or computers. If “192.168.150.002” is not used in a network with an IP address of “192.168.150.XXX”, you don’t have to change the projector IP address.

• For details about each setting, consult your network administrator.

Factory default setting:

192.168.150.002 Enter an IP address appropriate for the network. Factory default setting:

255.255.255.000 Set the subnet mask to the same as that of the computer and equipment on the network. Factory default setting: 000. 000. 000. 000 * When not in use, set to “000. 000.

000. 000”.

Description

Page 43

2 Select “TCP/IP”, then press ENTER.

3 Enter “IP Address” using

and \, then press ENTER.

Network

Setting the TCP/IP

92 .

68 .

50 .

IP Address

Subnet Mask Gateway

55 .2

000 .

55 .2

000 .

55 .2

000 .

000

4 Enter “Subnet Mask” using

| and \, then press ENTER.

5 Enter “Gateway” using

\, then press ENTER.

000

| and

4 Confirming the

Projector Information

You can confirm the MAC address and projector name.

Displayed items

MAC Address

Projector

Note

• For information on how to change the projector name, see “SETUP MANUAL” contained in the supplied CD-ROM.

The MAC address of the projector is displayed. The projector name is displayed.

Description

Useful Features

-55

Maintenance

Cleaning the projector

■ Ensure the power cord is unplugged before cleaning the projector.

■ The cabinet as well as the operation panel is made of plastic. Avoid using benzene or thinner, as these can damage the finish on the cabinet.

■ Do not use volatile agents such as insecticides on the projector. Do not attach rubber or plastic items to the projector for long periods. The effects of some of the agents in the plastic may cause damage to the quality or finish of the projector.

Mild detergent

diluted with water

Thinner

Wax

Cleaning the lens

■ Use a commercially available blower or lens cleaning paper (for glasses and camera lenses) for cleaning the lens. Do not use any liquid type cleaning agents, as they may wear off the coating film on the surface of the lens.

■ As the surface of the lens can easily get damaged, be careful not to scrape or hit the lens.

Cleaning

Paper

Cleaning the exhaust and intake vents

■ Use a vacuum cleaner to clean dust from the exhaust vent and the intake vent.

■ Wipe off dirt gently with a soft flannel cloth.

■ When the dirt is hard to remove, soak a cloth in a

mild detergent diluted with water, wring the cloth well and then wipe the projector. Strong cleaning detergents may discolor, warp or damage the coating on the projector. Make sure to test on a small, inconspicuous area on the projector before use.

-56

Info

• If you want to clean the air vents during projector operation, ensure you press STANDBY/ON on the projector or STANDBY on the remote control and put the projector into standby mode. After the cooling fan has stopped, unplug the power cord from the AC socket and clean the vents.

• The air filters should be cleaned every 100 hours of use. Clean the filters more often when the projector is used in a dusty or smoky location.

Replacing the Air Filter

• This projector is equipped with air filters to ensure the optimal operating condition of the projector.

• Ask your nearest Sharp Authorized Projector Dealer or Service Center to exchange the filter (PFILDA022WJKZ) when it is no longer possible to clean.

Replacing the Air Filter

1 Press STANDBY/ON on the pro-

jector or STANDBY on the remote control to put the projector into the standby mode.

• Wait until the cooling fan stops.

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

STANDBY button

STANDBY/ON button

3 Remove the filter cover.

• Tu rn over the projector. Pull down the car-

rying handle (1), grab the tab (2) and slide open the filter cover (3).

4 Remove the air filter.

• Pick the air filter up with your fingers and lift it out of the filter cover.

AC socket

Tab

Appendix

-57

Replacing the Air Filter

5 Place a replacement air filter.

• Place the new air filter onto the filter cover.

6 Replace the filter cover.

• Slide the filter cover in the direction of the arrow to close it.

Note

• Ensure the filter cover is securely installed. The power will not turn on unless it is correctly installed.

-58

Maintenance Indicators

■ The warning lights on the projector indicate problems inside the projector.

■ If a problem occurs, either the temperature indicator or the lamp indicator will illuminate red, and

the projector will enter the standby mode. After the projector has entered the standby mode, follow the procedures given below.

Maintenance Indicators

Power indicator Lamp indicator Temperature warning indicator

About the temperature warning indicator

If the temperature inside the projector increases, due to blockage of the air vents, or the setting location,

“ ” will illuminate in the lower left corner of the picture. If the temperature keeps on rising, the lamp will

turn off and the temperature warning indicator will blink, the cooling fan will run for a further 90 seconds, and

then the projector will enter the standby mode. After “

described on page 60.

” appears, ensure you perform the measures

About the lamp indicator

■ When the remaining lamp life becomes 5% or less, “ ” (yellow) and “Change The Lamp.” will be

displayed on the screen. When the percentage becomes 0%, it will change to “

automatically turn off and then the projector will automatically enter the standby mode. At this time,

the lamp indicator will illuminate in red.

■

If you try to turn on the projector a fourth time without replacing the lamp, the projector will not turn on.

” (red), the lamp will

Appendix

-59

Maintenance Indicators

Maintenance indicator

Temperature

warning

indicator

Lamp

indicator

Power

indicator

Normal

Off

Green on

Green blinks

when the lamp

is warming up

Green on/

Red on

Green blinks

(Cooling)

Abnormal

Red on (Standby)

Red on

Red on (Standby)

Red blinks

Problem

The internal temperature is abnormally high.

The lamp does not illuminate.

Time to change the lamp.

The lamp does not illuminate.

The power indicator blinks in red when the projector is on.

Cause Possible solution

• Relocate the projector to an area

• Blocked air intake

• Cooling fan break-

down

• Internal circuit failure

• Clogged air intake

• The lamp is shut

down abnormally.

• Remaining lamp life becomes 5% or less.

• Burnt-out lamp

• Lamp circuit failure

• The filter cover, lamp

unit cover or lens housing cover is open.

• Cooling fan breakdown

with proper ventilation (see page

8).

• Ta ke the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 68) for repair.

• Clean the exhaust and intake vents. (See page 56.)

• Disconnect the power cord from the AC outlet, and then connect it again.

• Carefully replace the lamp. (See page 62.)

• Ta ke the projector to your nearest Sharp Authorized Projector Dealer or Service Center (see page 68) for repair.

• Please exercise care when replacing the lamp.

• Securely install the lamp unit cover.

• If the power indicator blinks even

when the covers are securely installed, or if the cooling fan does not run normally, then contact your nearest Sharp Authorized Projector Dealer or Service Center (see page 68) for advice.

Info

• If the temperature warning indicator illuminates and the projector enters the standby mode, check whether any of the ventilation holes are blocked (see page 8) and then try turning the power back on. Wait until the projector has cooled down completely before plugging in the power cord and turning the power back on. (At least 10 minutes.)

• If the power is turned off for a brief moment due to power outage or some other cause while using the projector, and the power supply recovers immediately after that, the lamp indicator will illuminate in red and the lamp may not be lit. In this case, unplug the power cord from the AC outlet, replace the power cord in the AC outlet and then turn the power on again.

• The cooling fan keeps the internal temperature of the projector constant and this function is controlled automatically. The sound of the cooling fan may change during operation because the fan speed may change and this is not a malfunction.

-60

Regarding the Lamp

Lamp

■ It is recommended that the lamp unit (optional: AN-C430LP) be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display. See page 53.

■ Purchase a replacement lamp unit of type AN-C430LP from your place of purchase, nearest Sharp Authorized Projector Dealer or Service Center.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center. For the name of the nearest Sharp Authorized Projector Dealer or Service Center, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

Caution Concerning the Lamp

■ This projector utilizes a pressurized mercury lamp. A loud sound may indicate lamp failure. Lamp failure can be attributed to numerous sources such as: excessive shock, improper cooling, surface scratches or deterioration of the lamp due to a lapse of usage time. The period of time up to failure largely varies depending on the individual lamp and/or the condition and the frequency of use. It is important to note that failure can often result in the bulb cracking.

■ When the lamp replacement indicator and on-screen display icon are illuminated, it is recommended that the lamp be replaced with a new one immediately, even if the lamp appears to be operating normally.

■ Should the lamp break, the glass particles may spread inside the lamp cage or gas contained in the lamp may be vented into the room from the exhaust vent. Because the gas in this lamp includes mercury, ventilate the room well if the lamp breaks and avoid all exposure to the released gas. In case of exposure to the gas, consult a doctor as soon as possible.

■ Should the lamp break, there is also a possibility that glass particles may spread inside of the projector. In such a case, it is recommended you contact your nearest Sharp Authorized Projector Dealer or Service Center to assure safe operation.

U.S.A. ONLY

Replacing the Lamp

Caution

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn

or injury.

• Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool

before removing the lamp unit.

■ Carefully change the lamp by following the instructions described in this section. *If you wish, you

may have the lamp replaced at your nearest Sharp Authorized Projector Dealer or Service Center.

* If the new lamp does not illuminate after replacement, take your projector to the nearest Sharp Authorized

Projector Dealer or Service Center for repair.

Appendix

-61

Regarding the Lamp

Removing and Installing the Lamp Unit

Warning!

• Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.

Info

• Do not touch the glass surface of the lamp unit or the inside of the projector.

• To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the

projector or STANDBY on the remote control to put the projector into standby mode.

• Wait until the cooling fan stops.

Optional

accessory

Lamp unit AN-C430LP

STANDBY/ON button

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down (about 1 hour).

3 Remove the lamp unit cover.

• Loosen the user service screw (1) that secures the lamp unit cover. Slide down (2) and remove the lamp unit cover (3).

4 Remove the lamp unit.

• Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

-62

AC socket

User service screw (for lamp unit cover)

Securing screws

5 Insert the new lamp unit.

• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6 Replace the lamp unit cover.

• Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

• You can also reset the lamp timer via the LAN. (Refer to the SETUP MANUAL on the supplied CD-ROM for details.)

1 Connect the power cord.

• Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

•

While simultaneously holding down ", ENTER and MENU on the projector, press STANDBY/ON on the projector and keep all four buttons pressed down until the lamp indicator starts blinking green.

User service screw (for lamp unit cover)

AC socket

Lamp indicator

STANDBY/ON button

ENTER button " button

MENU button

Appendix

• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.

-63

Storing the Projector

How to Use the Storage Case

When storing the projector, attach the lens cap to the lens, and place it in the supplied storage case.

1 Open the cover of the storage

case.

2 Place the projector into the stor-

age case.

Info

• Ensure the projector has cooled down sufficiently before placing it in the case.

• Ensure the lens cap is attached to the lens for protection.

• Place the projector into the storage case with the lens facing the handle.

• Ensure the projector is held in place by using the fixing band.

Lens cap

Fixing band

3 Close the cover of the storage

case.

4 Place the accessories in the front

pocket of the storage case.

Supplied accessories (Remote control, etc.)

-64

Computer Compatibility Chart

Computer

• Multiple signal support Horizontal Frequency: 15–110 kHz Ver tical Frequency: 43–85 Hz

The following is a list of modes that conform to VESA. However, this projector supports other signals that are not VESA standards.

Mode Resolution VESA

640 × 350

640 × 400

720 × 350

VGA

SVGA

XGA

WXGA

SXGA

SXGA+

UXGA MAC 13" MAC 16" MAC 19" MAC 21"

720 × 400

640 × 480

800 × 600

1024 × 768

1280 × 720 1280 × 768

1280 × 800

1360 × 768 1366 × 768

1152 × 864

1280 × 1024

1400 × 1050

1600 × 1200

640 × 480

832 × 624 1024 × 768 1152 × 870

Horizontal Frequency

(kHz)

27.0

31.5

37.9

27.0

31.5

37.9

27.0

31.5

27.0

31.5

37.9

26.2

31.5

34.7

37.9

37.5

43.3

31.3

35.2

37.9

46.6

48.1

46.9

53.7

40.3

48.4

56.5

60.0

68.7

45.0

47.8

49.7

62.8

47.7

47.8

55.0

66.2

67.5

64.0

80.0

64.0

65.3

75.0

34.9

49.7

60.2

68.7

Pixel Clock: 12–170 MHz Sync signal: Compatible with TTL level

• Compatible with sync on green signal

Vertical Frequency

(Hz)

60 70 85 60 70 85 60 70 60 70 85 50 60 70 72 75 85 50 56 60 70 72 75 85 50 60 70 75 85 60 60 60 75 60 60 60 70 75 60 75 60 60 60 67 75 75 75

Analog RGB

Support

✔

Digital RGB

Support

✔

Note

• This projector may not be able to display images from notebook computers in simultaneous (CRT/LCD) mode. Should this occur, turn off the LCD display on the notebook computer and output the display data in “CRT only” mode. Details on how to change display modes can be found in your notebook computer’s operation manual.

• When this projector receives 640 × 350 VESA format VGA signals, “640 × 400” appears on the screen.

• When projecting the RGB interlace signal using COMPUTER/COMPONENT 1, 2 or DVI-D with “Signal Type”

set to “Auto” or “RGB”, the image may not be projected as desired. In this case, use either Video or S-Video.

• Depending on the computer you are using, the output signal may not be faithful to the “Screen resolution” adjustment. Check the settings of the computer’s signal output. If the settings cannot be changed, it is recommended that the resolution be set to the one that corresponds to “1280 × 800”.

DTV

Signal Vertical Frequency (Hz) DVI SupportHorizontal Frequency (kHz)

480 480P 540P

576 576P 720P 720P

1080

1080 1080P 1080P

I I

15.7

31.5

33.8

15.6

31.3

37.5

45.0

28.1

33.8

56.3

67.5

60 60 60 50 50 50 60 50 60 50 60

✔

✔ ✔ ✔ ✔ ✔ ✔ ✔

Appendix

-65

Troubleshooting

Problem

No picture and no sound

or projector does not start.

Sound is heard but no

picture appears.

Color is faded or poor.

Picture is blurred;

noise appears.

Picture appears but no

sound is heard.

Check

• Projector power cord is not plugged into the wall outlet.

• Power to the external connected devices is off.

• The selected input mode is wrong.

• The AV MUTE function is working.

• Cables incorrectly connected to the rear panel of the projector.

• Remote control batteries have run out.

•

External output has not been set when connecting notebook computer.

• The filter cover, lamp unit cover or lamp housing cover is not installed correctly.

• If the connected DVI digital equipment is turned on before the “DVI-D” input mode is selected on the projector, the image may not be projected properly or may not be displayed at all. Ensure that the appropriate input mode has been selected on the projector before you turn on the connected equipment.

• Cables incorrectly connected to the rear panel of the projector.

• “Bright” is set to minimum position.

• Depending on the computer you are using, an image may not

be projected unless the signal output setting of the computer is switched to the external output. Refer to the computer’s operation manual for how to switch its signal output settings.

• Image adjustments are incorrectly set.

(Video, S-Video Input only)

• Video input system is incorrectly set.

(COMPUTER/COMPONENT 1, 2, DVI-D only)

• Input signal type (RGB/Component) is incorrectly set.

• Adjust the focus.

• The projection distance exceeds the focus range.

• There is fog on the lens. If the projector is carried from a cold

room into a warm room, or if it is suddenly heated, condensation may form on the surface of the lens and the image will become blurred. Please set up the projector at least one hour before it is to be used. If condensation should form, remove the power cord from the wall outlet and wait for it to clear.

(Computer Input only)

• Perform “SIG-ADJ” Adjustments. (“Clock” Adjustment)

• Perform “SIG-ADJ” Adjustments. (“Phase” Adjustment)

• Noise may appear depending on the computer.

• Cables incorrectly connected to the rear panel of the projector.

• Volume is set to minimum.

• When the projector is connected to an external device and the

volume is set to minimum, the sound is not output even if you turn up the volume of the external device.

• “Speaker” is set to “Off”.

Page

—

34 34

23-29

15 23 60

23-29

—

33 19

—

47 47

—

23-29

Data image is not

centered.

-66

• Make the necessary adjustments of each item in the “SIG-ADJ” menu.

• Depending on the computer you are using, the output resolution signal may be different from the one you have set. For details, refer to the operation manual of the computer.

—

CheckProblem Page

An unusual sound is

occasionally heard

from the cabinet.

Maintenance

indicator illuminates or

blinks in red.

The projector cannot be turned on or put into the standby mode using the

STANDBY/ON button on

the projector.

Picture is green with

component input signals

(COMPUTER/

COMPONENT 1, 2, DVI-D) Picture is pink (no green)

with RGB input signals

(COMPUTER/

COMPONENT 1, 2, DVI-D)

Picture is too bright and

whitish.

The black levels of the

image show banding or

appear faded when DVI-

D is selected.

The cooling fan becomes noisy.

The lamp does not light

up even after the

projector turns on.

The lamp suddenly turns

off during projection.

The image sometimes

flickers.

The lamp takes a long

time to turn on. Picture is dark.

The remote control

cannot be used.

• If the picture is normal, the sound is due to cabinet shrinkage caused by room temperature changes. This will not affect operation or performance.

• See “Maintenance Indicators”.

• The keylock is set.

If the keylock is set to ON, all the buttons are locked.

• Change the input signal type setting.

• Image adjustments are incorrectly set.

• Select the Dynamic Range setting (“Standard” or “Enhanced”)

that results in the best picture quality.

• When temperature inside the projector increases, the cooling fan runs faster.

• The lamp indicator is illuminating in red. Replace the lamp.

• Cables incorrectly connected to the projector or the connected equipment works improperly.

• If this happens frequently, replace the lamp.

• The lamp will eventually need to be changed.

The lamp has reached the end of its life. Replace the lamp.

• Operate the remote control while pointing it at the projector’s remote control sensor.

• The remote control may be too far away from the projector.

• If direct sunlight or a strong fluorescent light is shining on the

projector’s remote control sensor, place the projector where it will not be affected by strong light.

• The batteries may be depleted or inserted incorrectly. Make sure the batteries are inserted correctly or insert new ones.

—

23-29

62 62

This projector is equipped with a microprocessor. Its performance could be adversely affected by incorrect operation or interference. If this should happen, unplug the projector and plug it in again after more than 5 minutes.

Appendix

-67

For SHARP Assistance

If you encounter any problems during setup or operation of this projector, first refer to the “Troubleshooting” section on pages 66 and 67. If this operation manual does not answer your question, please contact the SHARP Service departments listed below.

U.S.A. Sharp Electronics Corporation

1-888-GO-SHARP (1-888-467-4277) lcdsupport@sharpsec.com http://www.sharpusa.com

Canada Sharp Electronics of Canada Ltd.

(905) 568-7140 http://www.sharp.ca

Mexico Sharp Electronics Corporation Mexico

Branch

(525) 716-9000 http://www.sharp.com.mx

Latin America Sharp Electronics Corp. Latin American

Group

(305) 264-2277 www.servicio@sharpsec.com http://www.siempresharp.com

Germany Sharp Electronics (Europe) GMBH

01805-234675 http://www.sharp.de

U.K. Sharp Electronics (U.K.) Ltd.

08705 274277 http://www.sharp.co.uk/customersupport

Italy Sharp Electronics (Italy) S.P.A.

(39) 02-89595-1 http://www.sharp.it

Benelux SHARP Electronics Benelux BV

0900-SHARPCE (0900-7427723) Nederland 9900-0159 Belgium http://www.sharp.nl http://www.sharp.be http://www.sharp.lu

Australia Sharp Corporation of Australia

Pty. Ltd.

1300-135-022 http://www.sharp.net.au

New Zealand Sharp Corporation of New Zealand

Phone: (09) 573-0111 Fax: (09) 573-0112 http://www.sharp.net.nz

Singapore Sharp-Roxy Sales (S) Pte. Ltd.

65-226-6556 ckng@srs.global.sharp.co.jp http://www.sharp.com.sg

Hong Kong Sharp-Roxy (HK) Ltd.

(852) 2410-2623 dcmktg@srh.global.sharp.co.jp http://www.sharp.com.hk

Taiwan Sharp Corporation (Taiwan)

0800-025111 http://www.sharp-scot.com.tw

France Sharp Electronics France

01 49 90 35 40 hotlineced@sef.sharp-eu.com http://www.sharp.fr

Spain Sharp Electronica Espana, S.A.

93 5819700 sharplcd@sees.sharp-eu.com http://www.sharp.es

Switzerland Sharp Electronics (Schweiz) AG

0041 1 846 63 11 cattaneo@sez.sharp-eu.com http://www.sharp.ch

Sweden Sharp Electronics ( Nordic ) AB

(46) 8 6343600 vision.support@sen.sharp-eu.com http://www.sharp.se

Austria Sharp Electronics (Europe) GMBH

Branch Office Austria

0043 1 727 19 123 pogats@sea.sharp-eu.com http://www.sharp.at

-68

Malaysia Sharp-Roxy Sales & Service Co.

(60) 3-5125678

U.A.E. Sharp Middle East Fze

971-4-81-5311 helpdesk@smef.global.sharp.co.jp

Thailand Sharp Thebnakorn Co. Ltd.

02-236-0170 svc@stcl.global.sharp.co.jp http://www.sharp-th.com

Korea Sharp Electronics Incorporated of

Korea

(82) 2-3660-2002 lcd@sharp-korea.co.kr http://www.sharpkorea.co.kr

India Sharp Business Systems (India)

Limited

(91) 11- 6431313 service@sharp-oa.com

Specifications

Model Display devices Resolution Lens

Input terminals

Output terminals

Control and communication terminals

Speakers Projection lamp Rated voltage Rated frequency Input current Power consumption (Standby)

Operation temperature Cabinet Dimensions (main body only) [W × H × D]

Weight (approx.)

F number Zoom Focus DVI-D (Compatible with HDCP) Computer/Component

(mini D-sub 15 pin) S-Video (mini DIN 4 pin) Video (RCA) Audio (ø3.5 mm stereo minijack) Audio (RCA) Computer/Component

(mini D-sub 15 pin) Audio (ø3.5 mm stereo minijack) LAN (RJ-45) USB (Type B) RS-232C (mini DIN 9 pin) Wired Remote

(ø3.5 mm stereo minijack)

XG-C455W/PG-C355W

0.74" LCD panel × 3 WXGA (1280 × 800) F 1.7 – 1.9 Manual, ×1.2 (f = 28.0 – 33.6 mm) Manual

×1 ×2

×1 ×1 ×2 ×2 (L/R) ×1

×1 (variable audio output) ×1 ×1 ×1 ×1

2 W (Mono) 275 W AC 100 – 240 V 50/60 Hz

3.6 A 360 W (3.4 W) with AC 100 V

345 W (4.4 W) with AC 240 V 41°F to 95°F (+5°C to +35°C) Plastic

/32" × 4" × 11 1/64"

12 (326 × 101.5 × 279.5 mm)

10.8 lbs. (4.9 kg)

As a part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product improvement without prior notice. The performance specification figures indicated are nominal values of production units. There may be some deviations from these values in individual units.

Appendix

-69

Index

2D Progressive ......................................................... 46

3D Progressive ......................................................... 46

AC socket ................................................................. 30

Adjustment buttons ................................................... 43

All Reset ................................................................... 53

Area Zoom ................................................................38

Aspect ratio .........................................................37, 38

AUDIO input terminal ......................................... 23-26

Audio Output ............................................................. 51

AUDIO output terminal ............................................. 29

Auto V-Keystone ................................................. 32, 49

Auto Power Off ......................................................... 51

Auto Restart .............................................................. 51

Auto Sync (Auto Sync adjustment) .......................... 47

AUTO SYNC button .................................................. 35

AV MUTE button ....................................................... 34

Background ............................................................... 50

Blue ........................................................................... 45

Bright......................................................................... 45

Clock .........................................................................47

CLR Temp (Color Temperature) ............................... 45

Color ......................................................................... 45

COMPUTER/COMPONENT 1 input terminal .... 23, 25

COMPUTER/COMPONENT 2 input terminal .... 23, 25

Contrast .................................................................... 45

DHCP Client ............................................................. 55

DIN-D-sub RS-232C adaptor ................................... 27

DNR .......................................................................... 46

Dot By Dot ................................................................ 37

Dynamic Range ........................................................ 48

DVI-D input terminal ...........................................24, 25

ECO+QUIET button .................................................. 35

Eco+Quiet Mode ....................................................... 46

ENTER button........................................................... 44

Exhaust vent .......................................................13, 56

Fan Mode .................................................................. 52

Film Mode ................................................................. 46

FREEZE button ........................................................ 35

Full ............................................................................ 37

Game ........................................................................ 45

Gateway .................................................................... 55

Height Adjustment button ......................................... 31

H-Pos ........................................................................47

Image Shift................................................................ 49

INPUT buttons .......................................................... 34

Intake vent .......................................................... 13, 56

IP Address ................................................................ 55

Kensington Security Standard connector ................ 13

Keycode .................................................................... 52

Keylock ..................................................................... 53

KEYSTONE button ................................................... 32

Keystone Correction ...........................................32, 49

Lamp .........................................................................61

Lamp indicator ....................................................30, 59

Lamp Timer (Life) ..................................................... 53

LAN terminal .............................................................28

Language (on-screen display language).................. 50

LAN/RS232C ............................................................ 51

L-CLICK button ......................................................... 39

Lens cap ................................................................... 12

Lens cap strap .......................................................... 10

MAC Address ............................................................ 55

MAGNIFY buttons .................................................... 36

MENU button ............................................................ 43

-70

Menu Position ...........................................................50

MNR .......................................................................... 46

Monitor Output .......................................................... 51

MONITOR output terminal ........................................ 28

MOUSE/Adjustment buttons .............................. 39, 43

Movie ........................................................................ 45

Network ...............................................................42, 54

Normal ................................................................ 37, 38

ON button ................................................................. 30

Optional accessories ................................................ 10

OSD Display ............................................................. 50

PAGE Up/Down buttons ........................................... 39

Password .................................................................. 54

PDF ............................................................................. 6

Phase ........................................................................ 47

Picture .................................................................40, 45

Picture Mode............................................................. 45

PICTURE MODE button ...........................................36

Power cord ................................................................ 30

Power indicator ................................................... 30, 59

Presentation.............................................................. 45

PRJ-ADJ .............................................................42, 51

PRJ mode ................................................................. 50

Progressive ............................................................... 46

Projector ................................................................... 55

R-CLICK/RETURN button ..................................39, 43

Red ........................................................................... 45

Remote control ......................................................... 14

Remote control sensor ............................................. 15

Remote receiver ....................................................... 39

Replacing the lamp ................................................... 61

Reset ......................................................................... 45

Resize .......................................................................49

RESIZE button .......................................................... 37

Resolution ................................................................. 47

RGB cable ................................................................ 23

RS-232C ................................................................... 52

RS-232C terminal .....................................................27

SCR-ADJ ............................................................ 41, 49

Sharp ........................................................................ 45

SIG-ADJ .............................................................. 41, 47

Signal Info ................................................................. 48

Signal Type ............................................................... 47

Speaker .................................................................... 51

sRGB ........................................................................ 45

Standard ................................................................... 45

STANDBY button ...................................................... 30

Storage case............................................................. 64

Stretch ................................................................ 37, 38

Subnet Mask ............................................................. 55

Supplied accessories ............................................... 10

S-VIDEO input terminal ............................................26

System Lock ............................................................. 52

System Sound .......................................................... 51

TCP/IP ...................................................................... 55

Temperature warning indicator ................................. 59

Tilt dial ....................................................................... 31

Tint ............................................................................ 45

USB terminal............................................................. 39

VIDEO input terminal ................................................ 26

Video System ............................................................ 48

Volume buttons ......................................................... 34

V-Po s ........................................................................ 47

V-Stretch ................................................................... 38

WIRED REMOTE terminal ....................................... 14

SHARP CORPORATION

Sharp PG-C355W, XG-C455W Operating Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

How to Read this Operation Manual

Contents

How to Access the PDF Operation Manuals

IMPORTANT SAFEGUARDS

Accessories

Part Names and Functions

Using the Remote Control

Usable Range

Inserting the Batteries

Quick Start

Setting Up the Projector

Setting Up the Projector

Projection (PRJ) Mode

Samples of Cables for Connection

Connections

Connecting to a Computer

Connecting to Video Equipment

Controlling the Projector by a Computer

Connecting to a Monitor with RGB Input Terminal

Connecting to an Amplifier or Other Audio Equipment

Turning the Projector On/Off

Connecting the Power Cord

Turning the Projector On

Image Projection

Using the Adjustment Feet

Correcting Trapezoidal Distortion

Adjusting the Lens

Switching the Input Mode

Adjusting the Volume

Displaying the Black Screen and Turning off the Sound Temporarily

Displaying and Setting the Break Timer

Switching the Eco+Quiet Mode

Auto Sync (Auto Sync Adjustment)

Freezing a Moving Image

Displaying an Enlarged Portion of an Image

Selecting the Picture Mode

Resize Mode

Using the Remote Control as the Wireless Computer Mouse

Menu Items

Using the Menu Screen

Menu Selections (Adjustments)

Picture Adjustment (“Picture” menu)

Selecting the Picture Mode

Adjusting the Image

Adjusting the Color Temperature

Selecting the Progressive Mode

Selecting the Film Mode

Mosquito Noise Reduction (MNR)

Reducing Image Noise (DNR)

Eco+Quiet Mode Setting

Adjusting the Computer Image

Auto Sync Adjustment

Signal Type Setting

Resolution Setting

Selecting the Dynamic Range

Setting the Video System

Checking the Input Signal

Screen Adjustment (“SCR-ADJ” Menu)

Setting the Resize Mode

Keystone Correction

Adjusting the Image Position

Setting the On-screen Display

Helpful Functions Set during Installation (“PRJ-ADJ” menu)

LAN/RS232C

Auto Power Off Function

Speaker Setting

Audio Output Type Setting

2 Auto Restart Function

Monitor Output

Fan Mode Setting

System Lock Function

Keylock Function

Setting up the Projector Network Environment (“Network” menu)

Setting a Password

DHCP Client Setting