Sharp PC354N1T Datasheet

PREPARED BY:

DATE:

SPEC. No. ED-9466 1B

I

October 29. 1999

APPROVED BY: DATE:

DEVICE SPECIFICATION FOR

MODEL No.

I

SHA

ELECTRONIC COMPO GROUP SHARP CORPORATION

SPECIFICATION

PHOTOCOUPLER

OF’TO-ELECT=

I

Business dealing name

I I

PC354

1. These speciilcation sheets include materials protected under copyright of Sharp Corporation (‘Sharp”). Please do not reproduce or cause anyone to reproduce them without Sharp’s consent.

2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility

for any damage resulting from use of the product which does not comply with the absolute maximum ratings

and the instructions included in these specification sheets, and the precautions mentioned below.

(Precautions)

(1) This product is designed for use in the following application areas :

l

OA equipment

. Telecommunication equipment (Terminal) * Measuring equipment

l

Tooling machines l Computers

1

If the use of the product in the above application areas is for equipment listed in paragraphs

(21 or (31, please be sure to observe the precautions given in those respective paragraphs.

(21 Appropriate measures, such as fail-safe design and redundant design considering

the safety design of the overall system and equipment, should be taken to ensure reliability and safety when this product is used for equipment which demands high reliability and safety in function and precision, such as ;

* Transportation control and safety equipment (aircraft, train, automobile etc.) * Tram signals * Gas leakage sensor breakers * Rescue and security equipment

l

Other safety equipment

[

(31 Please do not use this product for equipment which require extremely high reliability

and safety in function and precision, such as :

* Space equipment * Telecommunication equipment (for trunk lines) * Nuclear power control equipment * Medical equipment

[

(4) Please contact and consult with a Sharp sales representative if there are any questions

regarding interpretation of the above three paragraphs.

3. Please contact and consult with a Sharp sales representative for any questions about this product.

Audio visual equipment

* Home appliances

1

CUSTOMERS APPROVAL

DATE

BY

DATE PRESENTED ;(i

BY

K. Hachimura. Department General Manager of Engineering Dept. ,I1 Opto-Electronic Devices Div. ELECOM Group

SHARP CORPORATION

4

SHARP CORPORATION

1. Application This specification applies to the outline and characteristics of p

Model No. PC354.

2. Outline Refer to the attached drawing No. CY6488KO2.

3. Ratings and characteristics

Refer to the attached sheet, page 4 to 6.

ED-94(

4. Reliability Refer to the attached sheet, page 7.

5. Incoming inspection

Refer to the attached sheet, page 8.

6. Supplement

6.1 Isolation voltage shall be measured in the following method. (1) Short between anode and cathode on the primary side and between

collector and emitter on the secondary side. (2) The dielectric withstand tester with zero-cross circuit shall be used. (3) The wave form of applied voltage shall be a sine wave.

6.2 Packaging specifications

SHARPCORPORATION

6.3 Collector current (Ic) Delivery rank table

(“0”

mark : indicates business dealing name of ordered product)

Rank at Business delivery dealing name

8

6.4 This Model is approved by UL. Approved Model No. : PC354 UL file No. : E64380

6.5 This product is AC input type.

6.6 This product is not designed against irradiation. This product is operated with electrical input and output. This product incorporates non-coherent light emitting diode.

PC354NT A or no mark 0.2 to 4.0 PC354N 1T A 0.5 to 1.5

Rank mark

Ic b-M

Test

conditions

I,=+ 1mA V ca=5v Ta=25C

6.7 ODS materials This product shall not contain the following materials.

Also, the following materials shall not be used in the production process

for this product. Materials for ODS : CFC,, Halon. Carbon tetrachloride.

1.1.1 -Trichloroethane (Methylchloroform)

6.8 Brominated flame retardants Speciiic brominated flame retardants such as the PBBO, and PBB, are not used

in this device at all.

7. Notes Refer to the attached sheet- 1- 1, 2.

SHARP CORPORATION

2. Outline

Sharp mark

“S”,

Model No.

Primary side mark

\

3.6kO. 3

.

c

@

;

2.54kO.25

1

\,

\

. .

\*

0

i

Date code

/

0

Anode

(Cathode)

0

Cathode

(Anode)

Pin Nos. and internal connection diagram

i

3

Collector

3 Emitter

d

&nk mark

mark

Epoxy resin

+q=, g

6”

4-L

*l) 2-digit number shall be marked according to DIN standard. *2) Factory identification mark shall be or shall not be marked. *3) Rank mark : “A” or no mark

l

4) Marking is laser marking

Product mass : Approx. 0. lg

Name

UNIT: l/l mm

PC354 Outline Dimensions

(Business dealing name : PC354NT)

Drawing

L

No.

CY6488KO2

SHARP CORPORATION

3. Ratings and characteristics

3.1 Absolute maximum ratings

Input

output

Collector current

* 1 Total power dissipation Operating temperature Topr Storage temperature Tstg *3 Isolation voltage Viso(rms) 3.75 *4 Soldering temperature Tsol 260 %

* 1 The derating factors of absolute maximum ratings due to ambient temperature

are shown in Fig. 1 to 4. *2 Pulse widths 100 /1 s. Duty ratio : 0.00 1 (Refer to Fig. 51 *3 AC for 1 min. 40 to 6O%RH, f=GOHz *4 For 10s

-30 to +lOO ‘C

-40 to +125 “C kV