Sharp NAR0051 Manual revised
Notice for Users in the USA
FCC Statement
WARNING - FCC Regulations state that any unauthorized changes or modifications
to this equipment not expressly approved by the manufacturer could void the user’s
authority to operate this equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in
a residential installation. This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may cause
harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause
harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
Reorient or relocate the receiving antenna.
•
Increase the distance between the equipment and receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the
•
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
•
A shielded I/F cable and included ferrite core for LAN cable is required to insure
compliance with FCC regulation for Class B computing equipment.
* As an ENERGY STAR
the ENERGY STAR
Declaration of Conformity
SHARP PERSONAL COMPUTER, PC-AV Series
This device complies with part 15 of the FCC rules. Operation is subject to the following
conditions:(1) this device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07430-2135
TEL: 1-800-BE-SHARP
®
Partner, SHARP has determined that this product meets
®
guidelines for energy efficiency.
i
About the Modem
This equipment complies with Part 68 of FCC rules. On the bottom of this equipment
is a label that contains, among other information, the FCC registration number and
ringer equivalence number (REN) for this equipment. If requested, this information
must be provided to the telephone company.
The modem jack of this equipment complies with Sub-part F of Part 68 of FCC rules.
The REN is used to determine the quantity of devices which may be connected to the
telephone line. Excessive RENs on the telephone line may result in the devices not
ringing in response to an incoming call. In most, but not all areas, the sum of the
RENs should not exceed five (5.0). To be certain of the number of devices that may
be connected to the line, as determined by the total RENs contact the telephone
company to determine the maximum REN for the calling areas.
If the terminal equipment causes harm to the telephone network, the telephone
company will notify you in advance that temporary discontinuance of service may be
required. But if advance notice isn't practical, the telephone company will notify the
customer as soon as possible. Also, you will be advised of your right to file a
complaint with the FCC if you believe it necessary.
The telephone company may make changes in its facilities, equipment, operations, or
procedures that could affect the operation of the equipment. If this happens, the
telephone company will provide advance notice in order for you to make the
necessary modifications in order to maintain uninterrupted service.
If trouble is experienced with this equipment, please contact Sharp Electronics Corp.
for repair and (or) warranty information (Refer to the provided Consumer Limited
Waranty). If the trouble is causing harm to the telephone network, the telephone
company may request you remove the equipment from the network until the problem
is resolved.
The equipment cannot be used on public coin service provided by the telephone
company. Connection to Party Line Service is subject to state tariffs. (Contact the
state public utility commission, public service commission or corporation commission
for information.)
ii
The Telephone Consumer Protection Act of 1991 makes it unlawful for any person to
use a computer or other electronic device, including fax machines, to send any
message unless such message clearly contains in a margin at the top or bottom of each
transmitted page or on the first page of the transmission, the date and time it is sent
and an identification of the business or other entity, or other individual sending the
message and the telephone number of the sending machine or such business, other
entity, or individual. (The telephone number provided may not be a 900 number or
any other number for which charges exceed local or long-distance transmission
charges.) To program this information, refer to the manual of the communication
software.
Warning
This product utilizes tin-lead solder, and fluorescent lamp containing a small amount
of mercury.
Disposal of these materials may be regulated due to environmental considerations.
For disposal or recycling information, please contact your local authorities or the
Electronics Industries Alliance: www.eiae.org
Copyright
It is the intent of Sharp that this product be used in full compliance with the copyright
laws of the United States and that prior permission be obtained from copyright owners
whenever necessary.
Product Information and Customer Assistance
For Product Information and Customer Assistance:
Call: 1-800-BE-SHARP (237-4277)
Sharp Systems of America
5901 Bolsa Avenue, Huntington Beach, CA 92647
Home Page: http://www.sharpsystems.com
E-mail address: ssa-support@sharpsystems.com
iii
TO PREVENT ELECTRICAL SHOCK, DISCONNECT THE AC CORD AND THE
BATTERY BEFORE SERVICING.
CAUTION:
FOR A COMPLETE ELECTRICAL DISCONNECTION, PULL OUT THE MAIN
PLUG AND THE BATTERY.
VORSICHT:
UM DIE STROMZUFUHR VOLLSTÄNDIG ZU UNTERBRECHEN, DEN
NETZSTECKER HERAUSZIEHEN UND DIE BATTERIE ÈNTFERNEN.
ATTENTION:
POUR UN ARRET TOTAL DU SYSTEME, DECONNECTEZ LA PRISE DE
COURANT SECTEUR ET LA BATTERIE.
VARNING:
FÖR TOTAL ELEKTRISK URKOPPLING, KOPPLA UR KONTAKTEN OCH TA
UR BATTERIET.
PRECAUCION:
PARA UNA COMPLETA DESCONEXION ELECTRICA DESENCHUFE LA
CLAVIJA DE LA RED Y LA BATERIA.
CAUTION:
iv
Safety Precautions
General
Follow all cautions and instructions, which may be marked, on your computer.
•
Except as described elsewhere in this manual, refer all servicing to qualified
•
personnel. Immediately shut off your computer and seek servicing under the
following conditions:
when the power cord or plug is damaged or frayed
•
when liquid has been spilled on your computer
•
when your computer has been dropped or the cabinet has been damaged
•
Location
Do not expose your computer to direct sunlight.
•
Try to avoid dusty environments.
•
Keep your computer away from any magnetic devices and TVs.
•
Keep your computer away from excessive humidity or fluids such as rain, snow,
•
water spray, juice, coffee, steam, etc.
Do not move your computer from an extremely cold place to an extremely warm
•
place. A temperature difference of more than 10°C (18°F) will cause condensation
inside the unit, which may cause damage.
Do not block or cover slots or openings on the cabinet. They protect your computer
•
from overheating.
Do not place your computer on an unstable or uneven work surface.
•
Care should be exercised when using on heat sensitive surfaces or your lap as the
•
base of your computer will get hot.
Do not use your computer on your lap or any part of your body for an extended
•
period during operation or charging to avoid injury from heat exposure.
Usage
Never push any kinds of objects into cabinet openings. They may touch dangerous
•
voltage points or short parts that could result in fire or electrical shock.
Turn off your computer before installing or removing any peripheral devices except
•
when connecting USB devices, an IEEE1394 device, a PC card, etc.
v
Check the AC power cord and power connectors periodically for damage. Change
•
the power cord immediately if damage is found.
Never subject your computer to sudden shocks or extreme vibration.
•
Do not drop your computer nor hit it with other equipment.
•
Do not scratch the surface of the LCD screen.
•
Turn off your computer and disconnect the AC power cord before cleaning.
•
Battery Pack Precautions
CAUTION
DANGER OF EXPLOSION IF BATTERY IS INCORRECTLY REPLACED.
REPLACE ONLY WITH THE SAME OR EQUIVALENT TYPE RECOMMENDED
BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO
THE MANUFACTURER'S INSTRUCTIONS.
Handling
Never put the battery pack in a fire, as it could explode and cause injury.
•
Do not attempt to open or alter the battery pack.
•
Do not place the battery where it might get hotter than 60°C (140°F).
•
The battery pack must be kept from metal objects such as jewelry and liquids. They
•
might trigger a short circuit and consequently cause the battery pack to heat up and
explode.
Do not allow liquids to come in contact with the battery pack.
•
Care must be taken not to drop the pack. A violent shock damages the pack.
•
Do not solder anything to the battery terminals.
•
vi
About This Manual
Notice
Information in this manual is subject to change without notice and does not represent a
commitment on the part of SHARP Corporation and its sales subsidiaries.
SHARP Corporation and its sales subsidiaries shall not be liable for technical or editorial
errors or omissions contained herein; nor for incidental or consequential damages resulting
from the furnishing, performance, or use of this material.
SHARP strongly recommends that separate permanent written records be kept of all important
data. Data may be lost or altered in virtually any electronic memory product under certain
circumstances. Therefore, SHARP assumes no responsibility for data lost or otherwise
rendered unusable whether as a result of improper use, repairs, defects, battery replacement,
use after the specified battery life has expired, or any other causes.
SHARP assumes no responsibility directly or indirectly, for financial losses or claims from
third persons resulting from the use of this product and any of its functions, such as stolen
credit card numbers, the loss of or alteration of stored data, etc.
Edition
1st Edition, July 2003.
Copyright
© 2003 SHARP Corporation
This document contains or refers to proprietary information which is protected by copyright.
All rights are reserved. Copying or other reproduction of this document is prohibited without
the prior written permission of SHARP Corporation.
Trademarks
AMD, the AMD logo, AMD Athlon, and AMD PowerNow! are trademarks of Advanced
Micro Devices, Inc.
IBM is a trademark of International Business Machines Corporation.
Microsoft and Windows are registered trademarks of Microsoft Corporation in the United
States and other countries. Windows Media is a trademark of Microsoft Corporation in
the United States and other countries.
WinDVD is a registered trademark of InterVideo, Inc.
Dolby and the double-D symbol are registered trademarks of Dolby Laboratories
Licensing Corporation.
Power Quest is a registered trademark and EasyRestore is a trademark of PowerQuest
Corporation.
BAPCo is a registered trademark of the Business Applications Performance Corporation.
MobileMark is a trademark of the Business Applications Performance Corporation.
viii
All other brand and product names are trademarks or registered trademarks of their
respective holders.
ix
Recording Important Information
For future reference, please record the following information in the spaces provided
below.
Model Number:
Serial Number:
Date of purchase:
Dealer’s Name:
Place of purchase:
Password:
The serial number is printed on a sticker located on the bottom of your computer.
x
Manual Conventions
This manual uses a set of style conventions described below.
Notes and Cautions are italicized with icons:
A note icon informs you of a special technique or information that may
help you perform a task or better understand a process.
A caution icon alerts you to something that may cause problems or
damage to hardware, software or data.
Key Labels on the Keyboard, when referred to in the instructions, are shown in
boldface:
Press Enter to continue.
When two or more keys are pressed simultaneously, the key labels are separated by a
plus (+) sign:
Restart your computer by pressing Ctrl+Alt+Delete.
Sample Entries are shown in lower cases of different typeface.
c:\windows\system
Words/Texts on Screen, such as window titles or possible parameters, are italicized:
Double-click this icon to display the Power Options Properties window.
Set the item to Enabled.
Screens reproduced in this manual may differ slightly from the screens you see on
your computer.
Section Titles in other parts of this manual are italicized:
Refer to Installing Battery Pack section of Chapter 1.
xi
Table of Contents
Notice for Users in the USA.......................................................................................i
Safety Precautions .....................................................................................................v
About This Manual.................................................................................................viii
Recording Important Information..............................................................................x
Manual Conventions.................................................................................................xi
Table of Contents.....................................................................................................xii
Overview of Computer...........................................................................................xiv
Quick Setup
Installing Battery Pack............................................................................................1-1
Connecting to AC Power Source............................................................................1-2
Setting Up Windows...............................................................................................1-4
Turning Off Your Computer...................................................................................1-6
Basic Operations
Choosing Power Source..........................................................................................2-1
Resetting System ....................................................................................................2-3
Using Glide Pad......................................................................................................2-4
Using Keyboard......................................................................................................2-6
Using Optical Drive................................................................................................2-7
Writing Data to CD-R/RW Disk...........................................................................2-10
Watching DVD Video ..........................................................................................2-11
Controlling Volume..............................................................................................2-15
Adjusting Display................................................................................................. 2-16
Sharing Your Computer........................................................................................2-19
Battery and Power Management
Battery Pack............................................................................................................3-1
Optional Add-on Battery Pack................................................................................3-6
Power Management..............................................................................................3-10
xii
Peripherals
Using Peripherals....................................................................................................4-1
Optional External Floppy Disk Drive Unit.............................................................4-3
External Display.....................................................................................................4-5
Audio System .........................................................................................................4-7
USB Device..........................................................................................................4-11
PC Card.................................................................................................................4-12
Printer...................................................................................................................4-14
IEEE 1394 Device ................................................................................................4-15
Communication Functions
Built-in Modem ......................................................................................................5-1
LAN Unit................................................................................................................5-4
Wireless LAN.........................................................................................................5-7
Network Setup Utility...........................................................................................5-11
Setup Utility
Running the Setup Utility.......................................................................................6-1
Main Menu .............................................................................................................6-3
Advanced Menu......................................................................................................6-4
Security Menu.........................................................................................................6-4
Boot Menu..............................................................................................................6-6
Exit Menu...............................................................................................................6-6
Appendixes
Memory Module....................................................................................................A-1
Installing Weight Saver .........................................................................................A-4
Maintenance and Care ...........................................................................................A-6
Re-installation Instructions..................................................................................A-11
Troubleshooting
Index
xiii
,
Overview of Computer
Each number after an arrow indicates the page referring to the part. Actual
appearance of your computer may be slightly different depending on the model.
Front
Antennas
LCD Screen
→2-16
Battery Indicator
3-3
→2-1
Power Indicator
→2-1
Antenna Indicator
xiv
Glide Pad
→2-4
Keyboard
→2-6
Power Button
→1-3
Status Indicators
A
N
Scroll LockOptical Drive
Hard Disk
Caps Lock
Num Lock
,8,
Right
Security Slot
→A-9
Optical Drive
→2-7
Audio Output Jack
(S/PDIF Compliant)
→4-7
9
Left
Ventilation Openings
→v
Modem Jack
→5-2
Rear
AC Adapter Jack
→1-2
LAN Jack
→5-5
External Monitor
Port →4-6
USB Ports
→4-3,11,14
PC Card Slot
→4-12
IEEE1394
Connector
→4-15
Volume Control
→2-15
Microphone Jack
→4-10
Ventilation Openings
→v
S Video Output
Jack →2-13
xv
Bottom
Reset Switch
→2-3
Battery Pack
→3-1
Speaker
xvi
CHAPTER 1
Quick Setup
Your computer is designed and pre-configured for easy setup and use. This chapter
describes the steps to set up and run your computer as quickly as possible. Read this
chapter first.
Installing Battery Pack
Your computer is powered with either the rechargeable battery pack or AC power
source. See the next chapter for more information on the power sources. Before
starting to use your computer for the first time, follow these instructions.
1. Place your computer with the bottom up on a stable work surface.
2. Insert the battery pack into your computer by matching the projected parts of
the battery pack to the notched parts on your computer.
1
Projected Part
Notched Part
1-1
3. Push the battery pack until you hear the clicking sound.
1
4. Turn your computer over and go to the next section.
Connecting to AC Power Source
• Always use the AC adapter and AC power cord included with your
computer or the optional one (may not be available in some countries).
Using others may damage your computer.
• Always hold the AC power cord by the plug when removing it from the
wall outlet. Never pull on the cord.
• Never plug in and out the AC power cord with your wet hands.
• When using your computer for the first time, be sure to operate it on
AC power. On battery power instead, you may not be able to complete
the Windows setup if the battery does not have enough power.
1. Plug the AC adapter cable to the AC adapter jack on the rear side of your
computer.
2. Plug the AC power cord into the AC adapter.
3. Plug the AC power cord into a wall outlet.
1-2
AC Adapter Jack
AC Adapter
AC Power Cord
To Wall Outlet
4. Slide the display cover lock lever to the right until the display cover releases,
and raise the cover.
1
5. Press the power button to turn on your computer.
Display Cover Lock Lever
Power Button
When you turn on your computer, the power indicator ( ) turns green, your
computer goes through a self-test to detect any problems, and Windows setup process
starts. See the next page.
Power Indicator
1-3
Setting Up Windows
To setup Windows, follow the instructions on the screen. See also the Windows quick
start guide. It takes approximately 5-10 minutes to complete the entire setup process.
The steps in the setup process are as follows:
Configuring your location, language and keyboard type
1
•
Configuring your time zone
•
Accepting license agreement
•
Naming your computer
•
Creating an account
•
Completing configuration
•
• Do not turn off your computer until completing Windows setup. If you
turn it off, you may not be able to set up Windows later.
• Be sure to connect your computer to AC power source. An
undercharged battery may not be able to complete the Windows setup.
• Do not connect any peripheral devices to your computer until the
Windows setup is completed. Otherwise your computer may
malfunction.
• If the display turns off, some power management may function. In this
case, press any key to resume your computer from the power
management. . (Refer to Power Management section of Chapter 3.)
• If you cannot operate the keyboard or the glide pad, press the power
button for more than four seconds to turn off your computer. Be sure
that the power indicator turns off; then, after more than 10 seconds,
press the power button to turn on your computer again.
After completing the Windows XP setup:
Confirm Time Zone is correctly selected and set the date and time by double-
•
clicking the time appearing on the right of the taskbar to open Date and Time
Properties dialog box.
Press Fn+F1 ( ) keys to activate the integrated antennas for Wireless LAN
communication.
1-4
Properties Dialog Box on Windows
In this manual, you will often see the expression “XXX Properties dialog box.” The
dialog box is a window containing text boxes, check boxes, buttons, etc., with which
you can send commands to Windows or other applications. To open the properties
dialog boxes, click start - Control Panel. The Control Panel has two types of views:
Category View and Classic View. The Category View allows you to choose the
category that may be related to what you want to do, then, choose your task by
clicking it. The Classic View gives you the icons representing their components or
features. Double-click one of the icons to open its dialog box or window. Some of the
dialog boxes you will use often are:
• Display
• Phone and Modem Options
• Mouse
• Power Options
• System
Clicking Switch to XXX View string appearing at the upper left of the
Control Panel window allows you to toggle between the two views.
1
1-5
Turning Off Your Computer
When you’ve finished using your computer, turn it off with one of the following steps:
From the start menu
•
1. Click start – Turn Off Computer.
1
2. In the Turn off computer dialog box, click Turn Off.
With the power button
•
Before using this step, confirm that the power button is enabled to shut down your
computer. Follow these instructions.
1. Open Power Options Properties dialog box. Select Advanced tab.
2. Confirm that Shut down is selected in the pull-down menu of When I press the
power button on my computer.
Close the display cover to keep the screen and keyboard clean and protected.
If you have not saved the data, a dialog box will appear asking whether
you want to save it.
• Do not turn off or reset your computer while the hard disk indicator,
optical drive indicator, or the indicator on the optional external floppy
disk drive is lit. Doing so may damage or even wipe out the data.
• After turning off your computer you need to wait at least ten seconds
before turning it back on. Turning the power off and on in rapid
succession can damage your computer’s electrical circuitry.
1-6
CHAPTER 2
Basic Operations
This chapter describes the basic operations of your computer.
Choosing Power Source
You can use your computer with one of the following power sources:
AC power from a wall outlet
•
Use AC power whenever possible; rely on the battery only when AC power is not
available.
Rechargeable battery
•
A standard battery pack is supplied with your computer. You can also use an
optional add-on battery. See Chapter 3 for the battery information.
About Power Indicators
The following indicators show the power status of your computer.
Indicator Light Meaning
Power On (green) Operating
Blinking (green) In System Standby
Off Powered off or in System Hibernate
Battery On (green) Fully charged
Connected to AC
Power Source
Off Has power
Powered by
Battery
On (orange) Being charged
Blinking
(orange)
Blinking (red) Almost completely discharged
In abnormal state (Remove the
battery pack and install it again.)
(The warning beep sounds.)
2
2-1
The battery indicator is always off when your computer is turned off and not
connected to AC power source.
Using AC Adapter
When connected to a wall outlet, the AC adapter provides power for operation and
charges the battery pack. The AC input voltage can range from 100 to 240 volts so
2
that you can use your computer with the appropriate plug adapter.
• When the battery is hot, the battery indicator may turn off and stay off
until the battery becomes cool.
• For more information on System standby/hibernate, see Chapter 3.
The AC power cord included with your computer is appropriate for the
voltage used in the area in which you purchased your computer. If you
attempt to connect your computer to a wall outlet in other areas, check
the voltage of the outlet and use an AC power cord appropriate for the
outlet. Consult local service staff if you are not sure.
2-2
Resetting System
You may need to restart the system if your computer becomes inoperable or after
adding new hardware or software. When the message appears after the installation,
click OK, Yes, etc. to restart Windows.
You can also restart Windows by clicking start – Turn Off Computer; then, Restart.
Resetting may cause data loss. Use the resetting process only if the
normal Windows XP Shut Down does not work because of software
malfunction. Although resetting will not damage the system, you may lose
the data you are processing.
Warm Boot (Software Reset)
If the system is locked up because of a software problem, you can reset or reboot the
system by pressing the Ctrl+Alt+Del keys simultaneously and select Applications tab
of Windows Task Manager dialog box. Click the name of the program hanging up,
then, End Task. If this does not work, select Users tab and click Disconnect or Logoff,
then, Yes.
Power Switch
You can turn off your computer by pressing the power button if you encounter
hardware or software problems locking up the system. In this case, press the power
button for more than four seconds.
Reset Switch
If you cannot turn off your computer with the power button, you can use the reset
switch on the bottom of your computer. To reset the system, insert a narrow object
into the small hole to press the switch.
2
RESET
Reset Switch
2-3
Using Glide Pad
Your computer is equipped with an integrated pointing device called glide pad. Using
the glide pad, you can move the pointer, select an item from a menu and perform other
tasks in the same way you would with a mouse.
2
Pointer
Glide Pad
• Do not hit or scratch the surface of the glide pad with pointed objects
(such as a ballpoint pen).
• Do not operate the glide pad with a moist finger. This may cause the
glide pad to operate incorrectly.
Using Glide Pad
Take a moment to become familiar with how the glide pad works.
Place Your Fingertip
Place your left or right hand next to the glide pad, resting your wrist naturally in a
relaxed manner. Place your thumb or a finger(s) on the glide pad.
Move Your Fingertip
The rectangular surface of the glide pad acts like a miniature duplicate of the display.
As you slide your fingertip across the pad, the pointer on the screen moves in the same
direction across the screen. The glide pad is very sensitive, so you do not have to exert
much pressure on the pad. The glide pad will respond to a light touch from your
fingertip.
2-4
Click, Double-click, and Right-click
To click or double-click, you can use the left button just like that of a mouse. Instead
of clicking the left button, you can also just tap gently anywhere on the rectangular
pad. For right-clicking, you must use the right button.
Drag and Drop
You can move icons or windows by using “drag and drop” below:
1. Position the pointer over the object.
2. Press the left button; do not release it.
3. Holding down the button, move the pointer. The object moves together with the
pointer.
4. Release the button when the object reaches its destination.
Or you can tap the pad twice instead of pressing the left button in the step 2.
Scroll
You can scroll through information in a list or in a document by using the glide pad.
To view information vertically, place your finger on the most right part of the glide
pad and slide your finger up and down. To view horizontally, place your finger on the
bottom part of the glide pad and slide your finger to the left or the right. This
procedure works only in limited applications.
2
Changing Configuration
In the Mouse Properties dialog box, you can change the configuration of the glide
pad, such as swapping left and right buttons, changing the pointer size, etc. Doubleclick Touch Pad icon (
) on the taskbar to open the Mouse Properties dialog box.
2-5
Using Keyboard
Your computer, equipped with the Windows Enhanced Keyboard, provides all the
functionality of a full-sized desktop keyboard.
Special Keys
2
Windows Key
Application Key
System Function Keys
When pressed together with the Fn key, function keys set specific system parameters.
This combination is sometimes referred to as “hot keys”.
Fn + F1 (
Fn + F5 (
Fn + F6 (
Fn + F7 (
Fn + F11 (
Fn + F12 (
)
)
)
)
)
)
Do not use the function keys Fn+F5 during watching DVD videos or
animation, or playing a video game.
Opens the Windows start menu.
Opens an application-specific short-cut menu.
Equivalent to right-clicking.
Turns the wireless LAN antenna on and off.
(for built-in wireless LAN model only )
Rotates display mode between the LCD only, an external
monitor only, and both.
(when connecting an external monitor)
Decreases the LCD screen brightness.
Increases the LCD screen brightness.
Turns on and off the LCD screen.
Forces your computer into System standby/System
hibernate/Shut down. (See Power Management of Chapter 3
for more information.)
2-6
Using Optical Drive
Your computer is equipped with an optical drive allowing you to read from DVD and
CD and write onto CD-R/RW.
CAUTION FOR LASER
Handling Disk
•
•
•
Use of controls or adjustments or performance of procedures other
than those specified herein may result in hazardous radiation exposure.
Maximum output and wavelength of the laser:
108mW, 784nm(CD-R/RW)
6mW, 662nm(DVD-ROM)
CLASS1LASERPRODUCT
LASERKLASSE1
Do not write on either side of the disk, particularly the non-label side. Data is
read/written from/onto the non-label side. Do not mark this surface.
Keep your disks away from direct sunlight, heat and excessive moisture.
Always hold the disks by the edges. Fingerprints, dirt or water on the disks can
cause noise or mistracking. If a disk is dirty or does not play properly, clean it with
a soft, dry cloth, wiping straight out from the center, along the radius.
2
2-7
Inserting Disk
1. Make sure the optical drive indicator is not lit on; then, press the eject button.
2
2. Gentry pull out the tray.
The drive tray will pop out.
Optical Drive Indicator
Eject Button
3. Place your disk, label side up, onto the tray and slightly press the center of the
disk until it is locked into the place.
2-8
Loading...