Sharp MX-2300G, MX-2700G, MX-2300N, MX-2700N User Manual

MODEL:

DIGITAL FULL COLOUR MULTIFUNCTIONAL SYSTEM

Safety GuideSafety GuideSafety Guide

Before installing this product, be sure to read the
"CAUTIONS" and "INSTALLATION
REQUIREMENTS" sections.

MX-2300G
MX-2700G
MX-2300N
MX-2700N

Keep this manual close at hand for reference
whenever needed.

CAUTIONS

INSTALLATION REQUIREMENTS

SUPPLIES

SPECIFICATIONS

TO THE ADMINISTRATOR OF THE MACHINE

Caution!

For complete electrical disconnection, pull out the main plug.
The socket-outlet shall be installed near the equipment and shall be easily accessible.

Shielded network cable and USB cable must be used with this equipment to maintain compliance with standards.

➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

Required in IEC-950 (EN 60 950) - Europe

• The equipment should be installed near an accessible socket outlet for easy disconnection.

Required in Appendix ZB of BS 7002 (En 60 950) — United Kingdom

MAINS PLUG WIRING INSTRUCTIONS

The mains lead of this equipment is already fitted with a mains plug which is either a non-rewireable
(moulded) or a rewireable type. Should the fuse need to be replaced, a BSI or ASTA approved fuse
to BS1362 marked or
be used.
Always refit the fuse cover after replacing the fuse on the moulded plug. Never use the plug without
the fuse cover fitted.
In the unlikely event of the socket outlet in your home not being compatible with the plug supplied
either cut-off the moulded plug (if this type is fitted) or remove by undoing the screws if a rewireable
plug is fitted and fit an appropriate type observing the wiring code below.

DANGER: The fuse should be removed from the cut-off plug and the plug destroyed immediately
and disposed of in a safe manner. Under no circumstances should the cut-off plug be inserted
elsewhere into a 13A socket outlet as a serious electric shock may occur.

To fit an appropriate plug to the mains lead, follow the instructions below:
IMPORTANT: The wires in this mains lead are coloured in accordance with the following code:

As the colours of the wires in this mains lead may not correspond with coloured markings
identifying the terminals in your plug, proceed as follows:
The wire which is coloured GREEN-AND YELLOW must be connected to the terminal in the plug
which is marked with the letter E, or by the safety earth symbol
and-yellow.
The wire which is coloured BLUE must be connected to the terminal which is marked with the letter
N or coloured black.
The wire which is coloured BROWN must be connected to the terminal which is marked with the
letter L or coloured red.

If you have any doubt, consult a qualified electrician.
WARNING: THIS APPARATUS MUST BE EARTHED.

and of the same rating as the one removed from the plug must

GREEN-AND-YELLOW: Earth
BLUE: Neutral
BROWN: Live

Å@, or coloured green or green-

➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢

➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣➢➣

EMC (this machine)

Warning:

This is a Class A product. In a domestic environment this product may cause radio interference in which case the user may be
required to take adequate measures.

EMC (peripheral devices)

NOTE:

This equipment has been tested and found to comply with the limits for a Class B digital device.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.

Warranty

While every effort has been made to make this document as accurate and helpful as possible, SHARP Corporation makes no
warranty of any kind with regard to its content. All information included herein is subject to change without notice. SHARP is not
responsible for any loss or damages, direct or indirect, arising from or related to the use of this operation manual.
© Copyright SHARP Corporation 2005. All rights reserved. Reproduction, adaptation or translation without prior written permission is
prohibited, except as allowed under copyright laws.

Contents

CAUTIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

Laser information . . . . . . . . . . . . . . . . . . . . . . . . . . 3

INSTALLATION REQUIREMENTS . . . . . . . . . . . . . 4

SUPPLIES. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5

Storage of supplies. . . . . . . . . . . . . . . . . . . . . . . . . 5

Supply of spare parts and consumables . . . . . . . . 5

SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . 6

Machine specifications / copier specifications . . . . 6

Continuous copying speeds . . . . . . . . . . . . . . . . . . 8

Printable sizes . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Ambient environment . . . . . . . . . . . . . . . . . . . . . . . 8

Acoustic noise emission (measurement according to

ISO7779) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Emission concentration (measurement according to

RAL-UZ62: Edition Jan. 2002) . . . . . . . . . . . . . . . . 9

Reversing single pass feeder (automatic document

feeder) specifications . . . . . . . . . . . . . . . . . . . . . . . 9

Exit tray unit (right tray) specifications . . . . . . . . . . 9

Stand/1x500 sheet paper drawer specifications. . 10
Stand/2x500 sheet paper drawer specifications. . 10

Large capacity tray specifications . . . . . . . . . . . . 11

Finisher specifications . . . . . . . . . . . . . . . . . . . . . 12

Saddle stitch finisher specifications . . . . . . . . . . . 13

Punch module specifications (for finisher) . . . . . . 14

Punch module specifications (for saddle stitch

finisher). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

Printer specifications . . . . . . . . . . . . . . . . . . . . . . 15

Network scanner / Internet fax specifications. . . . 16

Pull scan function (TWAIN) specifications . . . . . . 16

Optional equipment . . . . . . . . . . . . . . . . . . . . . . . 17

TO THE ADMINISTRATOR OF THE MACHINE . . 20

Factory default passwords . . . . . . . . . . . . . . . . . . 20

Forwarding all transmitted and received data to the
administrator (document administration function)

Trademark acknowledgments . . . . . . . . . . . . . . . 22

. . . 20

Note:

• Considerable care has been taken in preparing this manual. If you have any comments or concerns about the manual, please
contact your dealer or nearest authorised service representative.

• This product has undergone strict quality control and inspection procedures. In the unlikely event that a defect or other problem is
discovered, please contact your dealer or nearest authorised service representative.

• Aside from instances provided for by law, SHARP is not responsible for failures occurring during the use of the product or its
options, or failures due to incorrect operation of the product and its options, or other failures, or for any damage that occurs due
to use of the product.

• This manual contains references to the fax function. However, please note that the fax function is not available in some countries
and regions.

As an ENERGY STAR® Partner, SHARP has determined that this product meets the ENERGY

®

STAR

guidelines for energy efficiency.

1

CAUTIONS

1. Do not touch the transfer belt. Scratches or smudges on the transfer belt will
cause dirty prints.

2. The fusing unit is extremely hot. Exercise care in this area.

3. Do not look directly at the light source. Doing so may damage your eyes.

4. Four adjusters are provided on all optional stand/paper drawer units. These
adjusters should be lowered until they contact the floor.
When moving the machine with the optional stand/paper drawer, be sure to
raise the adjusters. Also, unlock the two casters at the front of the optional
stand/paper drawer. After moving the machine, lower the four adjusters until
they reach the floor and lock the two casters.

5. Do not make any modifications to this machine. Doing so may result in
personal injury or damage to the machine.

6. The machine is heavy. To prevent injury when moving the machine, it is
recommended that it be moved by four or more persons.

7. Do not make copies of anything which is prohibited from copying by law. The
following items are normally prohibited from printing by national law. Other
items may be prohibited by local law.

●

Money ● Stamps ● Bonds ● Stocks

●

Bank drafts ● Checks ● Passports ● Driver's licences

8. Do not use a flammable spray to clean the machine. If gas from the spray
comes in contact with hot electrical components or the fusing unit inside the
machine, fire or electrical shock may result.

9. Do not throw toner, a toner container (toner cartridge), or a waste toner box
into a fire. Toner may fly and cause burns.

10. Store toner, toner containers (toner cartridges), and waste toner boxes out of the reach of children.

Lock

Fusing unit

Adjuster

Release

The machine includes the document filing function, which stores document image data on the machine's hard drive. Stored
documents can be called up and printed or transmitted as needed. If a hard drive failure occurs, it will no longer be possible to call
up the stored document data. To prevent the loss of important documents in the unlikely event of a hard drive failure, keep the
originals of important documents or store the original data elsewhere.
With the exception of instances provided for by law, Sharp Corporation bears no responsibility for any damages or loss due to the
loss of stored document data.

"BATTERY DISPOSAL"

THIS PRODUCT CONTAINS A LITHIUM PRIMARY MEMORY BACK-UP BATTERY THAT MUST BE DISPOSED OF PROPERLY.
PLEASE CONTACT YOUR LOCAL SHARP DEALER OR AUTHORISED SERVICE REPRESENTATIVE FOR ASSISTANCE IN
DISPOSING OF THIS BATTERY.

Each instruction also covers the optional units used with these products.

2

CAUTIONS

Laser information

Wave length 785 nm +10 nm

-15 nm

Pulse times North America: 23 cpm model: (5.1 µs ±5.1 ns)/7 mm

27 cpm model: (5.1 µs ±5.1 ns)/7 mm

Europe: 23 cpm model: (5.1 µs ±5.1 ns)/7 mm

27 cpm model: (5.1 µs ±5.1 ns)/7 mm

Output power Max 0.7 mW

At the production line, the output power of the scanner unit is adjusted to 0.233 MILLIWATT PLUS 5% and is maintained constant by
the operation of the Automatic Power Control (APC).

Caution

Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous radiation
exposure.

For North America:

SAFETY PRECAUTIONS

This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the CDRH standards. This means that
the equipment does not produce hazardous laser radiation. For your safety, observe the precautions below.

• Do not remove the cabinet, operation panel or any other covers.

• The equipment's exterior covers contain several safety interlock switches. Do not bypass any safety interlock by inserting wedges
or other items into switch slots.

For Europe:

CLASS 1 LASER PRODUCT

LASER KLASSE 1

LUOKAN 1 LASERLAITE

KLASS 1 LASERAPPARAT

CLASS 3B INVISIBLE LASER

CAUTION

RADIATION WHEN OPEN AND
INTERLOCKS DEFEATED.
AVOID EXPOSURE TO BEAM.

VORSICHT

UNSICHTBARE
LASERSTRAHLUNG DER
KLASSE 3B, WENN
ABDECKUNG GEÖFFNET UND
SICHERHEITSVERRIEGELUNG
ÜBERBRÜCKT. NICHT DEM
STRAHL AUSSETZEN.

ADVARSEL

USYNLIG LASERSTRÅLNING
AF KLASSE 3B VED ÅBNING,
NÅR SIKKERHEDSBRYDERE
ER UDE AF FUNKTION. UNDGÅ
UDSÆTTELSE FOR
STRÅLNING.

USYNLIG KLASSE 3B
LASERSTRÅLNING NÅR
DEKSEL ÅPNES OG
SIKKERHEDSLÅS BRYTES .
UNNGÅ EKSPONERING FOR
STRÅLEN.

OSYNLIG LASERSTRÅLNING
KLASS 3B NÄR DENNA DEL ÄR
ÖPPNAD OCH SPÄRRAR ÄR
URKOPPLADE. UNDVIK
EXPONERING FÖR STRÅLEN.

AVATTAESSA JA
SUOJALUKITUS OHITETTAESSA
OLET ALTTIINA NÄKYMÄTÖNTÄ
LUOKAN 3B LASERSÄTEILYLLE.
ÄLÄ KATSO SÄTEESEEN.

ADVARSEL

VARNING

VAR O!

The above label is affixed to the laser
unit inside the machine.

3

INSTALLATION REQUIREMENTS

Improper installation may damage this product. Please note the following during initial installation and whenever the
machine is moved.

1. The machine should be installed near an accessible
power outlet for easy connection.

2. Be sure to connect the power cord only to a power
outlet that meets the specified voltage and current
requirements. Also make certain the outlet is properly
grounded.

• For the power supply requirements, see the name
plate at the bottom of the back of the left side of the
machine.

Connect the machine to a power outlet which is not
used for other electric appliances. If a lighting fixture is
connected to the same outlet, the light may flicker.

3. Do not install the machine in areas that are:

• damp, humid, or very dusty

• exposed to direct sunlight

• poorly ventilated

• subject to extreme temperature or humidity
changes, e.g., near an air conditioner or heater.

4. Be sure to allow the required space around the
machine for servicing and proper ventilation.

5. When moving the machine, four persons must firmly
grasp the transport handles on both sides of the
machine.

6. The machine includes a built-in hard drive. Do not
subject the machine to shock or vibration. In
particular, never move the machine while the power is
on.

30 cm
(11-13/16")

30 cm
(11-13/16")

A small amount of ozone is produced within the printer during operation. The emission level is insufficient to cause any health
hazard.

NOTE:

The present recommended long term exposure limit for ozone is 0.1 ppm (0.2 mg/m3) calculated as an 8 hr. time-weighted average
concentration.
However, since the small amount that is emitted may have an objectionable odor, it is advisable to place the copier in a ventilated
area.

45 cm
(17-23/32")

4

SUPPLIES

Standard supplies for this product that can replaced by the user include paper, toner cartridges, and staple cartridges for
the finisher.
Be sure to use only SHARP-specified products for the toner cartridges, finisher staple cartridge, saddle stitch finisher
staple cartridge, and transparency film.

For best copying results, be sure to use only Sharp Genuine Supplies which are designed,
engineered, and tested to maximize the life and performance of Sharp products. Look for the
Genuine Supplies label on the toner package.

GENUINE SUPPLIES

Storage of supplies

Proper storage

1. Store the supplies in a location that is:

• clean and dry,

• at a stable temperature,

• not exposed to direct sunlight.

2. Store paper in the wrapper and lying flat.

3. Paper stored in packages standing up or out of the wrapper may curl or become damp, resulting in paper misfeeds.

Storing toner cartridges

Store a new toner cartridge box horizontally. Do not store it standing on end. If stored standing on end, the toner may not
distribute well even after shaking the cartridge vigorously, and will remain inside the cartridge without flowing out.

Staple cartridge

The finisher and saddle stitch finisher require the following staple cartridge:
MX-SCX1

Staple cartridge for finisher (approx. 5000 per cartridge x 3 cartridges)
AR-SC2

Staple cartridge for saddle stitch finisher (approx. 5000 per cartridge x 3 cartridges)

Supply of spare parts and consumables

The supply of spare parts for repair of the machine is guaranteed for at least 7 years following the termination of
production. Spare parts are those parts of the machine which may break down within the scope of the ordinary use of
the product whereas those parts which normally exceed the life of the product are not to be considered as spare parts.
Consumables too, are available for 7 years following the termination of production.

5

SPECIFICATIONS

Machine specifications / copier specifications

Name

Type

Photoconductive type

Printing method

Developer system

Fusing system

First-copy time*

Scanning resolution

Printing resolution

Scanning gradation

Printing gradation

Original sizes / types

Copy sizes

Print margins

Warm-up time

Copy ratios

Tray 1

Tray 2

* First copy out time is measured with original on the document glass in full ready condition with fuser at operating temperature and

mirror motor at operating speed, actual time may vary based on environment conditions.

Digital Full Colour Multifunctional System MX-2300G/MX-2700G/MX-2300N/MX-2700N

Desktop

OPC drum

Electrophotographic system (laser)

Dry-type two-component magnetic brush development

Heat rollers

Colour copy time: 8.9 seconds Black and white copy time: 6.3 seconds
(Portrait feeding of A4 (8-1/2" x 11") sheets from 1st paper tray, without auto colour selection and
auto colour mode.)

Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory

Document glass

Colour scanning: 600 x 600 dpi (factory default values)

Reversing single pass
feeder (automatic
document feeder)

600 x 600 dpi

10 bits

Black and white printing: 2 tones (1 bit)
Colour printing: 2 tones per colour (1 bit) or 16 tones per colour (4 bits)

Max. A3 (11" x 17") / sheets, bound documents

Maximum: A3 (11" x 17") Minimum: A5R (5-1/4" x 5-3/4")

Leading edge: 4 mm (11/64") or less, trailing edge: 3 mm (1/8") or less, near edge / far edge: total
4 mm (11/64") or less

80 seconds or less

Variable: 25% to 400% in increments of 1%, total 376 increments (25% to 200% when the auto

document feeder is used)

Fixed presets: 25%, 50%, 70%, 81%, 86%, 100%, 115%, 122%, 141%, 200% and 400% for AB sizes;

25%, 50%, 64%, 77%, 100%, 121%, 129%, 200% and 400% for inch sizes.

Two reduction ratios and two enlargement ratios can be stored.
Paper sizes: A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",

8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m
Paper capacity: 500 sheets (80 g/m2 (21 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, and coloured paper

Paper sizes: A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",

8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m
Paper capacity: 500 sheets (80 g/m2 (21 lbs.))
Paper types: SHARP-recommended plain paper, recycled paper, and coloured paper

Black and white scanning: 600 x 600 dpi, 600 x 300 dpi (factory

Colour scanning: 600 x 600 dpi (factory default values)

2

to 105 g/m2 (16 lbs. to 28 lbs.))

2

to 105 g/m2 (16 lbs. to 28 lbs.))

default values)

default values)

6

Machine specifications / copier specifications (Continued)

Paper sizes Maximum: A3W (12" x 18") Minimum: A5R (5-1/4" x 5-3/4")
Paper weights:

Bypass tray

Duplex module

Output tray (Centre tray)

Required Power supply

Power consumption

Dimensions

Weight

Overall dimensions

Thin paper (55 g/m2 to 59 g/m2 (15 lbs. to 16 lbs.)), plain paper (60 g/m2 to 105 g/m2 (16 lbs. to
28 lbs.)), heavy paper (106 g/m
(20 lbs. to 24 lbs.))

Paper capacity:
Standard paper 100 sheets, envelopes 20 sheets, transparency films 20 sheets, heavy paper 40
sheets, tab paper 20 sheets, gloss paper 20 sheets

Paper types:
Plain paper, recycled paper, coloured paper, heavy paper, thin paper, transparency film, envelopes
(Monarch, Com-10, DL, C5)

Automatic paper size detection
When "Auto-AB" detection is selected:
A3W, A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 216 mm x 330 mm (8-1/2" x 13"), 8-1/2" x 11"
When "Auto-Inch" detection is selected:
12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R,
A3, B4, A4, B5

Paper size entry: The size can be entered from 148 mm to 432 mm (from 5-1/2" to 17") (W), from

100 mm to 297 mm (from 5-1/2" to 11-5/8") (H).

Tab paper: A4 size, tab widths 12 mm (31/64") to 20 mm (51/64")

8-1/2" x 11" size, tab widths 6.1 mm" (1/4") to 17 mm (43/64")

Paper sizes: A3, B4, A4, A4R, B5, B5R, A5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",

8-1/2" x 11"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR
Paper weight: Plain paper (60 g/m
SHARP-recommended plain paper, recycled paper, and coloured paper

Output location / method:
In machine body / Face-down output
(A3W and 12" x 18" paper can be output to right tray, finisher, or saddle stitch finisher)

Output capacity:
500 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)
(The maximum number of sheets that can be held varies depending on ambient conditions in the
installation location, the type of paper, and the storage conditions of the paper.)

Tray full sensor: Yes
Shifter function: Yes
Local voltage ±10% (For the power supply requirements, see the name plate at the bottom of the

back of the left side of the machine.)
220-240V: 1.84 kW 100-127V: 1.44 kW

MX-2300G / MX-2700G (with document cover):
620 mm (W) x 670 mm (D) x 825 mm (H) (24-13/32" (W) x 26-3/8" (D) x 32-15/32" (H))
MX-2300G / MX-2700G (with automatic document feeder):
620 mm (W) x 670 mm (D) x 950 mm (H) (24-13/32" (W) x 26-3/8" (D) x 37-13/32" (H))
MX-2300N / MX-2700N:
620 mm (W) x 670 mm (D) x 950 mm (H) (24-13/32" (W) x 26-3/8" (D) x 37-13/32" (H))

MX-2300G / MX-2700G (with document cover): Approx. 104 kg (229.2 lbs.)
MX-2300G / MX-2700G (with automatic document feeder): Approx. 112 kg (246.8 lbs.)
MX-2300N / MX-2700N: Approx. 112 kg (246.8 lbs.)

1050 mm (W) x 670 mm (D) (41-21/64" (W) x 26-3/8" (D)) (when bypass tray is extended)

2

to 209 g/m2 (28 lbs. to 56 lbs.)), envelopes (75 g/m2 to 90 g/m2

2

to 105 g/m2 (16 lbs. to 28 lbs.))

SPECIFICATIONS

7

SPECIFICATIONS

Continuous copying speeds*

Model

Copy ratio

Copy mode

A3, 11" x 17", 8K

B4, 8-1/2" x 14", 8-1/2" x 13"

Plain
paper*

2

Heavy
paper*

*1 Copy speed during output of the second copy and following copies when performing continuous one-sided copying of the same

*2 Using plain paper from any tray other than the bypass tray.
*3 When heavy paper is loaded in the bypass tray.

3

page (excluding offset output).

A4R, B5R, A5R, 8-1/2" x 11"R,
7-1/4" x 10-1/2"R,
5-1/2" x 8-1/2", 16KR

A4, B5, 8-1/2" x 11", 16K

Extra sizes

A4, B5, A5R, 8-1/2" x 11",
8-1/2" x 5-1/2"R, 16K

Other sizes

1

MX-2300G / MX-2300N MX-2700G / MX-2700N

100% / Reduced / Enlarged

Colour copying Black and white

copying

12 copies/min. 12 copies/min. 14 copies/min. 14 copies/min.

14 copies/min. 14 copies/min. 16 copies/min. 16 copies/min.

16 copies/min. 16 copies/min. 19 copies/min. 19 copies/min.

23 copies/min. 23 copies/min. 27 copies/min. 27 copies/min.

11 copies/min. 11 copies/min. 13 copies/min. 13 copies/min.

10 copies/min. 11 copies/min. 10 copies/min. 11 copies/min.

5 copies/min. 7 copies/min. 5 copies/min. 7 copies/min.

Colour copying Black and white

copying

Printable sizes Ambient environment

Paper size Printable size Paper size Printable size

A3W* 297 x 420 mm 12" x 18"* 279 x 432 mm
A3 293 x 413 mm 11" x 17" 275 x 425 mm
B4 253 x 357 mm 8-1/2" x 14" 212 x 349 mm
A4 206 x 290 mm 8-1/2" x 13" 212 x 323 mm
B5 178 x 250 mm 8-1/2" x 11" 212 x 272 mm
A5 144 x 203 mm 5-1/2" x 8-1/2 " 136 x 209 mm
7-1/4" x 10-1/2R" 180 x 260 mm 8K 266 x 383 mm
16K 191 x 263 mm
* When printing on A3W (12" x 18") size paper using the PCL or PS printer driver,

the maximum print area is 299 mm x 450 mm.

(Humidity)

85%

60%

20%

10˚C
(54˚F)

30˚C

35˚C (Temperature)

(86˚F)

(91˚F)

8

Acoustic noise emission (measurement according to ISO7779)

SPECIFICATIONS

Sound power level LwA

Printing mode (continuous printing)

Colour Black and white

6.3 B or less 6.3 B or less 5.5 B or less

Standby mode

Emission concentration (measurement according to RAL-UZ62: Edition Jan. 2002)

Ozone

Dust

Styrene

0.02 mg/m3 or less

0.075 mg/m3 or less

0.07 mg/m3 or less

Reversing single pass feeder (automatic document feeder) specifications

Model

Original sizes

Original weight

Capacity

MX-RPX1

A3 to A5, 11" x 17" to 5-1/2" x 8-1/2",
long paper (max. width 297 mm (11-45/64") x max. length 800 mm (31-31/64"), scanning in mono 2
mode of one side only is possible in fax and image scan modes.)

One-sided 35 g/m2 to 128 g/m2 (9 lbs. to 34 lbs.) (Paper weights from 35 g/m2 (9 lbs.) to 49 g/m2
(13 lbs.) require the use of slow scan mode.)
Two-sided 50g/m

100 sheets (80 g/m2 (21 lbs.)) Maximum stack height of 13 mm (1/2")

2

to 105 g/m2. (13 lbs. to 28 lbs.)

Power supply

Supplied from the machine

Exit tray unit (right tray) specifications

Model

Output method

Output capacity*

Dimensions

Weight

* The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of

paper, and the storage conditions of the paper.

MX-TRX1

Face-down output

100 sheets (using SHARP-recommended A4 or 8-1/2" x 11" paper)

When tray is folded up:
289 mm (W) x 405 mm (D) x 52 mm (H) (11-3/8" (W) x 15-61/64" (D) x 2-3/64" (H))
When tray is extended:
419 mm (W) x 405 mm (D) x 52 mm (H) (16-1/2" (W) x 15-61/64" (D) x 2-3/64" (H))

Approx. 0.93 kg (2 lbs.)

9

SPECIFICATIONS

Stand/1x500 sheet paper drawer specifications

Model

Paper sizes

Paper weight

Paper capacity

Paper types

Automatic paper size
detection

Power supply

Dimensions

Weight

MX-DEX1

A3, B4, A4, A4R, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, 8K, 16K, 16KR

Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))

500 sheets (80 g/m2 (21 lbs.)) x 1 tray

SHARP-recommended plain paper, recycled paper, and coloured paper

When "Auto-AB" automatic detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13")
When "Auto-Inch" detection is selected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R

Supplied from the machine

720 mm (W) x 670 mm (D) x 303 mm (H) (28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H)) (including adjuster)

Approx. 20 kg (44.1 lbs.)

Stand/2x500 sheet paper drawer specifications

Model

Paper sizes

Paper weight

MX-DEX2

A3, B4, A4, A4R, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, 8K, 16K, 16KR

Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))

Paper capacity

Paper types

Automatic paper size
detection

Power supply

Dimensions

Weight

500 sheets (80 g/m2 (21 lbs.)) x 2 trays

SHARP-recommended plain paper, recycled paper, and coloured paper

When "Auto-AB" detection is selected:
A3, B4, A4, A4R, B5, B5R, 216 mm x 330 mm (8-1/2" x 13")
When "Auto-Inch" detection is selected:
11" x 17", 8-1/2" x 14", 8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R

Supplied from the machine

720 mm (W) x 670 mm (D) x 303 mm (H) (28-11/32" (W) x 26-3/8" (D) x 11-15/16" (H)) (including adjuster)

Approx. 23.5 kg. (51.8 lbs.)

10

Large capacity tray specifications*

SPECIFICATIONS

Model

Paper sizes

Paper weight

Paper capacity

Paper types

Power supply

Dimensions

Weight

* Stand/1x500 sheet paper drawer (MX-DEX1) or stand/2x500 sheet paper drawer (MX-DEX2) is required.

MX-LCX1

A4, 8-1/2" x 11" (paper size change must be performed by a service technician)

Plain paper (60 g/m2 to 105 g/m2 (16 lbs. to 28 lbs.))

3500 sheets (80 g/m2 (21 lbs.))

SHARP-recommended plain paper, recycled paper and coloured paper

Supplied from the machine

370 mm (W) x 550 mm (D) x 520 mm (H) (14-9/16" (W) x 21-21/32" (D) x 20-15/32" (H))

Approx. 29 kg (63.9 lbs.)

11

SPECIFICATIONS

Finisher specifications

Model

Paper sizes

Paper weight

Modes

Allowed paper sizes for offset

Offset distance

Tray capacity*

1

Dimensions

Weight

Stapler section

Allowed paper sizes for
stapling

MX-FNX1

A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR

Thin paper (55g/m2 to 59g/m2 (15 lbs. to 16 lbs.)) Plain paper (60g/m2 to 105g/m2 (16 lbs. to 28 lbs.))
Heavy paper (106g/m2 to 209g/m2 (28 lbs. to 56 lbs.))

Non-staple, staple

A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K

30 mm (1-3/16")

Non-stapling:
500 sheets (A4, A4R, B5, B5R, A5R,
8-1/2" x 11", 8-1/2" x 11"R, 7-1/4" x 10-1/2"R,
5-1/2" x 8-1/2"R, 16K, 16KR)
250 sheets (A3W, A3, B4, 12" x 18", 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8K)

When tray is folded up:
440 mm (W) x 595 mm (D) x 205 mm (H) (17-21/64" (W) x 23-27/64" (D) x 8-5/64" (H))
When tray is extended:
640 mm (W) x 595 mm (D) x 205 mm(H) (25-3/16" (W) x 23-27/64" (D) x 8-5/64" (H))

Approx. 13 kg (28.7 lbs.)

A3, B4, A4, A4R, B5, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K, 16KR
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)

Stapling*
30 sets or 500 sheets (A4, A4R, B5, 8-1/2" x 11",
8-1/2" x 11"R, 16K, 16KR)
30 sets or 250 sheets (A3, B4, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8K)

2

:

Maximum number of
sheets for stapling*

*1 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of

paper, and the storage conditions of the paper.

*2 The maximum number of sheets for stapling assumes a paper weight of 90 g/m

106 g/m2 to 209 g/m2 (28 lbs. to 56 lbs.).

2

50 sheets (A4, A4R, B5, 8-1/2" x 11", 8-1/2" x 11"R, 16K, 16KR)
30 sheets (A3, B4, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8K)
(30 sheets when the sheets are the same width but different lengths.)

2

(24 lbs.) and includes two cover sheets of

12

SPECIFICATIONS

Saddle stitch finisher specifications*

Model

Paper sizes

Paper weight

Modes

Allowed paper sizes for offset

Offset distance

Tray capacity*

2

Dimensions

Weight

MX-FNX2

A3W, A3, B4, A4, A4R, B5, B5R, A5R, 12" x 18", 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 5-1/2" x 8-1/2"R, 8K, 16K, 16KR

Thin paper (55g/m2 to 59g/m2 (15 lbs. to 16 lbs.)) Plain
28 lbs.)) Heavy paper (106 g/m

Non-staple, staple

A3, A4, A4R, B4, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R,
7-1/4" x 10-1/2"R, 8K, 16K, 16KR

20 mm (25/32")

Non-stapling:
1000 sheets (A4, A4R, B5, B5R, 8-1/2" x 11",
8-1/2" x 11"R, 7-1/4" x 10-1/2"R, 16K, 16KR)
500 sheets (A3W, A3, B4, A5R, 12" x 18",
11" x 17", 8-1/2" x 14", 8-1/2" x 13",
5-1/2" x 8-1/2"R, 8K)

When tray is folded up:
555 mm (W) x 610 mm (D) x 1010 mm (H) (21-27/32" (W) x 24-1/64" (D) x 39-49/64" (H))
When tray is extended:
665 mm (W) x 610 mm (D) x 1050 mm (H) (26-11/64" (W) x 24-1/64" (D) x 41-21/64" (H))

Approx. 46 kg (101.4 lbs.)

1

2

to 209 g/m2 (28 lbs. to 56 lbs

Stapling*
50 sets (one staple at top left corner) or 1000
sheets (A4, B5, 8-1/2" x 11")
30 sets or 1000 sheets (A4, A4R, B5, B5R,
8-1/2" x 11", 8-1/2" x 11"R, 16K, 16KR)
30 sets or 500 sheets (A3, B4, 11" x 17",
8-1/2" x 14", 8-1/2" x 13", 8K)

paper (60 g/m2 to 105 g/m2 (16 lbs. to

.))

3

:

Stapler section

Allowed paper sizes for
stapling

Maximum number of
sheets for stapling*

Saddle unit

3

Stapling method

Folding position

Allowed paper sizes for

A3, B4, A4, A4R, B5, B5R, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8-1/2" x 11", 8-1/2" x 11"R, 8K, 16K,
16KR
(Three stapling positions: one staple at bottom left corner, one staple at top left corner, and two staples.)

30 sheets (A4, A4R, B5, B5R, 8-1/2" x 11", 8-1/2" x 11"R, 16K, 16KR)
25 sheets (A3, B4, 11" x 17", 8-1/2" x 14", 8-1/2" x 13", 8K)
(25 sheets when the sheets are the same width but different lengths.)

Fold in half and staple in two places on centreline

Fold at centreline (can be adjusted with "Saddle Stitch Position Adjust" in the System Settings)

A3, B4, A4R, 11" x 17", 8-1/2" x 11"R, 8K, 16KR

saddle stitch stapling

Allowed paper weights

55 g/m2 to 209 g/m2 (15 lbs. to 56 lbs.)

for saddle stitch stapling

Number sheets for saddle
stitch stapling / Number

Maximum: 10 sheets (80 g/m2 (21 lbs.) x 9 sheets + 209 g/m2 (56 lbs.) x 1 sheet) / 10 sets (6 to 10
sheets), 20 sets (1 to 5 sheets)

of sets

*1 Paper pass unit (MX-RBX1) and stand/1x500 sheet paper drawer (MX-DEX1) or stand/2x500 sheet paper drawer (MX-DEX2) are

required.

*2 The maximum number of sheets that can be held varies depending on ambient conditions in the installation location, the type of

paper, and the storage conditions of the paper.

*3 The maximum number of sheets for stapling assumes a paper weight of 90 g/m

106 g/m

2

to 209 g/m2 (28 lbs. to 56 lbs.).

2

(24 lbs.) and includes two cover sheets of

13

SPECIFICATIONS

Punch module specifications (for finisher)

Model

Hole punching

Allowed paper sizes for
punching

Punchable paper weights

MX-PNX1A MX-PNX1B MX-PNX1C MX-PNX1D

2 holes 2 holes or 3 holes 4 holes 4 holes, broad width

A3, B4, A4, A4R, B5,
B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
8K, 16K, 16KR

55 g/m2 to 209 g/m2 (15 lbs. to 56 lbs.)

2 holes:
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11"R
3 holes:
A3, A4, 11" x 17",
8-1/2" x 11"

A3, A4 A3, B4, A4, A4R, B5,

Punch module specifications (for saddle stitch finisher)

Model

Hole punching

Allowed paper sizes for
punching

Punchable paper weights

AR-PN1A AR-PN1B AR-PN1C AR-PN1D

2 holes 2 holes or 3 holes 4 holes 4 holes, broad width

A3, B4, A4, A4R, B5,
B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R,
8K, 16K, 16KR

55 g/m2 to 209 g/m2 (15 lbs. to 56 lbs.)

2 holes:
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11"R
3 holes:
A3, A4, 11" x 17",
8-1/2" x 11"

A3, A4 A3, B4, A4, A4R, B5,

B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R

B5R, 11" x 17",
8-1/2" x 14",
8-1/2" x 13",
8-1/2" x 11",
8-1/2" x 11"R

Note:

Special media such as transparency film and label sheets cannot be stapled or punched.

14

Printer specifications

SPECIFICATIONS

Type

Continuous printing speed

Printing resolution

Printer driver type

Supported protocols

Fonts

Interface port

Memory

Print area

*1 When the PS3 expansion kit (MX-PKX1) is installed and the machine is used as a PostScript printer.
*2 The standard printer driver of MX-2300G/MX-2700G
*3 When MX-2300G/MX-2700G are used, the printer expansion kit (MX-PBX1) is required.
*4 Barcode font kit (AR-PF1) is required.
*5 256MB expansion memory board (MX-SMX1) is required if one or more of the following is/are installed: Printer expansion kit

(MX-PBX1), PS3 expansion kit (MX-PKX1), Network scanner expansion kit (MX-NSX1), Internet fax expansion kit (MX-FWX1).

Built-in

Same as continuous copying speed (When printing same document continuously on A4
(8-1/2" x 11") plain paper in non-offset mode, excluding processing time.)

600 x 600 dpi / 1200 x 600 dpi*1 (black and white printing, rotating output not performed)

SPLC-c*2, PCL5c*3, PCL6*3, PostScript 3 compatible*

TCP/IP, IPX/SPX, NetBEUI, EtherTalk

PCL5c, PCL6 80 European fonts, 28 barcode fonts*4, 1 bitmap font
PostScript 3 compatible*
LAN connectivity: 10Base-T / 100Base-TX

USB (type A): Supports USB 2.0 (Full speed) USB (type B): Supports USB 2.0 (Hi speed)
MX-2300G/MX-2700G: 384 MB (256MB expansion memory board can be added.*5)

MX-2300N/MX-2700N: 640 MB
Entire page excluding margin of 4.2 mm (11/64") at each edge. The actual print area may vary

depending on the printer driver and the software application.

1

136 European fonts

1

15

SPECIFICATIONS

Network scanner*1 / Internet fax*2 specifications

Type

Scanning resolution (dpi)

Scanning speed
(Reversing single pass feeder)

Interface port

Supported protocols

File formats

Remarks

*1 When MX-2300G/MX-2700G are used, the network scanner expansion kit (MX-NSX1) is required.
*2 Internet fax expansion kit (MX-FWX1) is required.
*3 Total number of all destinations (Scan to E-mail, Scan to FTP, Scan to Desktop, Scan to Network folder, Internet Fax, Fax, and Group)

Colour scanner

100 x 100, 200 x 200, 300 x 300, 400 x 400, 600 x 600
Internet Fax: 200 x 100, 200 x 200, 200 x 400, 400 x 400, 600 x 600 (200 x 100, 200 x 200 when file
type is TIFF-S) Halftone can be selected for resolutions other than 200 x 100 dpi.

Colour (A4 / 8-1/2" x 11") One-sided: 35 pages/min. (200 x 200 dpi),

Two-sided: 15 pages/min. (200 x 200 dpi)

Black and white (A4 / 8-1/2" x 11") One-sided: 48 pages/min. (200 x 200 dpi),

Two-sided: 15 pages/min. (200 x 200 dpi)

LAN connectivity: 10Base-T / 100Base-TX

TCP/IP

Colour
(including greyscale)

Black and white

Internet Fax
(black and white only)

Number of one-touch keys for
storing destinations*

Number of destinations that can be
stored in a group (1 key)*

Expansion memory

3

3

File types: TIFF, JPEG, PDF, Encrypted PDF
Compression ratio: High / Medium / Low

File types: TIFF, PDF, Encrypted PDF
Compression modes: None / Medium (G3) / High (G4)

File types: TIFF-FX (TIFF-F, TIFF-S)
Compression modes: Medium (G3) / High (G4)

Maximum number of keys: 999

Maximum number of destinations in one group (1 key): 500

When using the MX-2300G or MX-2700G, 256MB expansion
memory board (MX-SMX1) is required if one or more of the
following is/are installed: Printer expansion kit (MX-PBX1), PS3
expansion kit (MX-PKX1), Network scanner expansion kit
(MX-NSX1), Internet fax expansion kit (MX-FWX1).

Pull scan function (TWAIN) specifications*

Supported protocol

Colour modes

Resolution settings

Scanning area

* This function can be used only when the network scanner function is installed.

TCP/IP

Full Colour, Greyscale, Mono Diffusion, Mono 2 gradation

75 dpi, 100 dpi, 150 dpi, 200 dpi, 300 dpi, 400 dpi, 600 dpi
(The resolution can be specified by entering a numerical value from 50 to 9600 dpi. However, when
a high resolution is specified, it is necessary to reduce the scanning area.)

Maximum: A3 (11" x 17")

16

SPECIFICATIONS

Optional equipment

MX-2300G MX-2700G MX-2300N MX-2700N

Document cover Yes No

Reversing single pass feeder Yes Standard

Exit tray unit Yes

Stand/1x500 sheet paper drawer Yes

Stand/2x500 sheet paper drawer Yes

Large capacity tray Yes

Finisher Yes

Saddle stitch finisher Yes

Punch module Yes

Printer function Standard (SPLC-c), Yes (PCL, PS) Standard (PCL), Yes (PS)

Network scanner function Yes Standard

Internet fax function Yes

Pull scan function (TWAIN) Yes Standard

Facsimile function Yes

Yes:Can be installed. No: Cannot be installed.

17

18

Information that the administrator of the machine requires is printed on
the back of this page.
(Separate this page from the manual and keep it in a safe place. In
addition, fill in the name of the administrator and the administrator's
contact information in the left hand margin.)

✂

Administrator Name: Contact at:

19

TO THE ADMINISTRATOR OF THE
MACHINE

(Separate this page from the manual and keep it in a safe place.)

Factory default passwords

When accessing the system settings, the administrator password is required to log in with administrator
rights. The system settings can be configured in the Web pages as well as on the operation panel. To
access the system settings using the Web pages, a password is also required.

Factory default administrator password

Factory default setting: admin

Store a new administrator password as soon as the machine is installed.
Once the administrator password has been changed, the new password is required to restore the factory
default password. Take care to remember the new password.

Factory default passwords (Web pages)

There are two factory default accounts: "Administrator" and "User". A person who logs in as an
"Administrator" can configure all settings in the Web pages. A person who logs in as a "User" can only
configure certain settings.
The factory default passwords are shown below.

Factory default account Factory default password

User users users

Administrator admin admin

Forwarding all transmitted and received data to the administrator
(document administration function)

This function is used to forward all data transmitted and received by the machine to a specified destination
(Scan to E-mail address, Scan to FTP destination, Scan to Network Folder destination, or Scan to Desktop
destination).
This function can be used by the administrator of the machine to archive all transmitted and received data.
To configure the document administration settings, click [Application Settings] and then [Document
Administration Function] in the Web page menu. (Administrator rights are required.)

Note:

• This function can be used only when the network scanner function is installed.

• The format, exposure, and resolution settings of transmitted and received data remain in effect when the data is
forwarded.

• The functions below cannot be used when transmitted faxes are forwarded. In this case, the [Memory TX] key and
[Direct TX] key do not appear.
Quick Online transmission, direct transmission, dialling using the speaker

✂

20

TO THE ADMINISTRATOR OF THE MACHINE

This equipment complies with the requirements of Directives 89/336/EEC and 73/23/EEC
as amended by 93/68/EEC.

Dieses Gerät entspricht den Anforderungen der EG-Richtlinien 89/336/EWG und
73/23/EWG mit Änderung 93/68/EWG.

Ce matériel répond aux exigences contenues dans les directives 89/336/CEE et 73/23/CEE
modifiées par la directive 93/68/CEE.

Dit apparaat voldoet aan de eisen van de richtlijnen 89/336/EEG en 73/23/EEG, gewijzigd
door 93/68/EEG.

Dette udstyr overholder kravene i direktiv nr. 89/336/EEC og 73/23/EEC med tillæg nr.
93/68/EEC.

Quest’ apparecchio è conforme ai requisiti delle direttive 89/336/EEC e 73/23/EEC, come
emendata dalla direttiva 93/68/EEC.

Este equipamento obedece às exigências das directivas 89/336/CEE e 73/23/CEE, na sua
versão corrigida pela directiva 93/68/CEE.

Este aparato satisface las exigencias de las Directivas 89/336/CEE y 73/23/CEE,
modificadas por medio de la 93/68/CEE.

Denna utrustning uppfyller kraven enligt riktlinjerna 89/336/EEC och 73/23/EEC så som
kompletteras av 93/68/EEC.

Dette produktet oppfyller betingelsene i direktivene 89/336/EEC og 73/23/EEC i endringen
93/68/EEC.

Tämä laite täyttää direktiivien 89/336/EEC ja 73/23/EEC vaatimukset, joita on muutettu
direktiivillä 93/68/EEC.

The CE mark logo label is affixed on an equipment in case that the directives described in the above
sentence are applicable to the product. (This sentence is not applicable in any country where the
above directives are not required.)

21

TO THE ADMINISTRATOR OF THE MACHINE

Trademark acknowledgments

The following trademarks and registered trademarks are used in conjunction with the machine and its peripheral devices and
accessories.

•

Microsoft®, Windows®, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, Windows® XP, Windows® Server
2003 and Internet Explorer

• PostScript is a registered trademark of Adobe Systems Incorporated.
Macintosh, Mac OS, AppleTalk, EtherTalk, LaserWriter, and Safari are registered trademarks or trademarks of Apple Computer, Inc.

•

• Netscape Navigator is a trademark of Netscape Communications Corporation.

• Adobe, the Adobe logo, Acrobat, the Adobe PDF logo, and Reader are registered trademarks or trademarks of Adobe Systems
Incorporated in the United States and other countries.

• PCL is a registered trademark of the Hewlett-Packard Company.

• IBM, PC/AT, and PowerPC are trademarks of International Business Machines Corporation.

• Sharpdesk is a trademark of Sharp Corporation.

• All other trademarks and copyrights are the property of their respective owners.

Candid and Taffy are trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may
be registered in certain jurisdictions. CG Omega, CG Times, Garamond Antiqua, Garamond Halbfett, Garamond Kursiv,
Garamond and Halbfett Kursiv are trademarks of Monotype Imaging, Inc. and may be registered in certain jurisdictions. Albertus,
Arial, Coronet, Gill Sans, Joanna and Times New Roman are trademarks of The Monotype Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Avant Garde, ITC Bookman, Lubalin Graph,
Mona Lisa, Zapf Chancery and Zapf Dingbats are trademarks of International Typeface Corporation registered in the United
States Patent and Trademark Office and may be registered in certain jurisdictions. Clarendon, Eurostile, Helvetica, Optima,
Palatino, Stempel Garamond, Times and Univers are trademarks of Heidelberger Druckmaschinen AG, which may be registered
in certain jurisdictions, exclusively licensed through Linotype Library GmbH, a wholly owned subsidiary of Heidelberger
Druckmaschinen AG. Apple Chancery, Chicago, Geneva, Monaco and New York are trademarks of Apple Computer Inc. and may
be registered in certain jurisdictions. HGGothicB, HGMinchoL, HGPGothicB and HGPMinchoL are trademarks of Ricoh
Company, Ltd. and may be registered in some jurisdictions. Wingdings is a registered trademark of Microsoft Corporation in the
United States and other countries. Marigold and Oxford are trademarks of Arthur Baker and may be registered in some
jurisdictions. Antique Olive is a trademark of Marcel Olive and may be registered in certain jurisdictions. Hoefler Text is a
trademark of Johnathan Hoefler and may be registered in some jurisdictions. ITC is a trademark of International Typeface
Corporation registered in the United States Patent and Trademark Office and may be registered in certain jurisdictions. Agfa is a
trademark of the Agfa-Gevaert Group and may be registered in certain jurisdictions. Intellifont, MicroType and UFST are
trademarks of Monotype Imaging, Inc. registered in the United States Patent and Trademark Office and may be registered in
certain jurisdictions. Macintosh and TrueType are trademarks of Apple Computer Inc. registered in the United States Patent and
Trademark Office and other countries. PostScript is a trademark of Adobe Systems Incorporated and may be registered in some
jurisdictions. HP, PCL, FontSmart and LaserJet are trademarks of Hewlett-Packard Company and may be registered in some
jurisdictions. The Type 1 processor resident in Monotype Imaging’s UFST product is under license from Electronics For Imaging,
Inc. All other trademarks are the property of their respective owners.

®

are registered trademarks or trademarks of Microsoft Corporation in the U.S.A. and other countries.

22

Safety Guide

MODEL:

MX-2300G
MX-2700G
MX-2300N
MX-2700N

PRINTED IN FRANCE

TINSE3164GHZZ