Sharp MD-SR75 User Manual

Quick Guide

PORTABLE MINIDISC RECORDER

MODEL

MD-SR75H

Quick Setup Guide

Follow the setup procedure (1-3)
before you use this unit.

Quick Operation Guide

Explains basic recording and playback
procedures.

Refer to the operation manual for details.

If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www. sharp.co.uk/support.
Customers without internet access may telephone
0990 274277 during office hour.

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

TINSE0326AWZZ

A0006.TO

1

Insert a MiniDisc

4

2

1

Insert according to
the direction arrow.

33

1 Slide the OPEN lever to re-

lease the compartment door.

3 Insert a MiniDisc as shown.
4 Close the compartment door.

2 Lift it up the compartment.

When you record on a MiniDisc,
check that the erase prevention tab
is set to the “recordable” position.

Recordable

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

Recording
prevented

2

Connect the AC adaptor

To the DC IN 5V socket.

AC 230-240V,
50/60 Hz

Insert securely, all the way in.

1 Plug the AC adaptor into the

wall socket.

Before using the unit with a rechargeable battery, the battery has to be charged.
Refer to “Battery Power”, page 30 (operation manual) for details.

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

To wall socket.

2 Insert the plug on the other

end into the DC IN 5V socket.

3

Connection

OPTICAL/

LINE IN

White: To Left

Red: To Right

AUDIO OUT

RIGHT LEFT

NOTE:

Refer to page 13 (operation manual) for connecting the unit to a stereo system
with “DIGITAL OUT” or “OPTICAL OUT” sockets.

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

T o a stereo system with “AUDIO OUT” or “LINE
OUT” sockets. (See left. Analogue connection)

Note:

● If the audio system has only one pair of socket then
they are usually input only and recording via this con­nection is not possible.

Preparation for use

Release the HOLD switch on the bottom of the unit before use.

The unit does not work if the switch is set to HOLD.

Hold

CAUTION:

It is not recommendable to put the
MiniDisc into a rear pocket, as this
may damage the product when sitting.

Released

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

Recording

Check that the unit is connected to the stereo system.

1 Press the REC button.

●Record pause mode is entered.

2 Begin playback on the stereo system connected to this unit.

●To enable the record level to be set.

3 Press the REC LEVEL (

ing level (analogue connection only).

●

Adjust the recording level so that the maximum sound volume from the
source makes the reading swing somewhere between –4 dB and 0 dB.

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

55

5 or

55

Level meter indicator

44

4) button to adjust the record-

44

0dB
4dB

Continued to the next page

Recording: continued

4 Press the P AUSE button on the stereo system to enter the play-

back pause mode at the point you wish to start recording.

●

Here you can select the track to be recorded.

5 Press the

0606

06 button to start the MiniDisc unit recording.

0606

6 Begin playback on the stereo system, the output will be re-

corded.

To stop recording

Press the • ■/:OFF button.

● When recording stops, “TOC” ap-

pears (Table Of Contents). Whilst
“TOC” appears the MiniDisc re­corded contents have not yet been
updated.

● To prevent the new recording from
being lost it is not possible to re­move the MiniDisc whilst “TOC” is
displayed.

TOC display

T o update the recorded contents
of the MiniDisc

Press the • ■/:OFF button whilst in
the stop mode.

● The power turns off after recorded
contents have been updated on the
MiniDisc.

About the TOC

After any recording or editing function
“TOC” (T able Of Contents) is displayed.
T o finalize the recording or editing func­tion, press the •
this process “TOC” will flash and “TOC
EDIT!” will be displayed.
During any recording or editing func­tion the MiniDisc unit Lid is locked, the
MiniDisc can not be removed until the
process is finalized.

Warning

●If the power is removed (Battery/AC
adapter) whilst “TOC” is displayed
the MiniDisc unit lid will remain
locked until the battery/main power
is restored and the unit is turned on.
Your new recordings or edited
changes will be lost and your
MiniDisc may become unusable.

■/:OFF button. During

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

Playing

To the
socket

1 Insert the earphones plug firmly into the earphones socket on

the remote control unit.

2 Plug the remote control into the socket on the unit.
3 Insert a MiniDisc.
4 Press the

● Playback starts automatically with a playback only MiniDisc or a MiniDisc
which is protected against accidental erasure (Auto-play function).

To stop playback

Press the • ■/:OFF button (Remote
control: press the ■ button).

● If the unit is not operated for at least
2 minutes whilst in the stop mode, the
power will shut off automatically.

Web-site: www.sharp.co.uk/support Help Line: 0990 274277 (office hours)

06 06

06 button.

06 06