In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is different in the display size from the LC-30HV4U/LC-30HV4D.
This service manual accordingly describes the display alone. For the entire AVC System, refer to the LC30HV4U/LC-30HV4D Servic e M a n u a l (S33Y2LC30HV4U).
» PARTS LIST ....................................................... 91
» PACKING OF THE SET ...................................115
LC-37HV4D
Page
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
Page 2
LC-37HV4U
22
LC-37HV4D
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
CAUTION: FOR CONTINUED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
AVC SIDE: F701 (T2AL, 250V)
LCD SIDE: F7501, F7502, F7503, F7504, F7551,
F7552, F7553, F7611, F7612, F7613, F7614, F7641,
F7642, F7643 (T1AL, 250V), F2701, F2702 (T2.5AH,
250V)
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks:
1. Inspect all lead dress to make certain that leads are
not pinched, and check that hardware is not lodged
between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
» Plug the AC cord directly into a 110~240 volt A C outlet.
» Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to an earth ground.
» Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity or measure the A C voltage drop
across the resistor.
» Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
All checks must be repeated with the AC cord plug
connection reversed. (If necessar y, a nonpolarized
adaptor plug must be used only for the purpose of
completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5
mA. rms AC.) or more is excessive and indicates a
potential shock hazard which must be corrected
before returning the monitor to the owner.
Many electrical and mechanical parts in LCD color
television have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage , w attage , etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
and shaded areas in the
Schematic Diagrams.
For continued protection, replacement parts must be
identical to those used in the original circuit.
The use of a substitute replacement parts which do not
have the same safety characteristics as the factory
recommended replacement parts shown in this service
manual, may create shock, fire or other hazards.
components having such features are identified by “ å”
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
PRECAUTION: POUR LA
PRO TECTION CONTINUE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE
CÔTÉ AVC:F701 (T2AL, 250V)
CÔTÉ LCD:F7501, F7502, F7503,
conduite électrique ou une prise de terre branchée à
la terre.
• Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
de la résistance.
• Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
(antenne, coffret métallique, tête des vis, arbres de
commande et des boutons, écusson, etc.) et mesurer
la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir
inversé la fiche du cordon d'alimentation. (Si nécessaire,
une prise d'adpatation non polarisée peut être utilisée
dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
2. Inspecter tous les dispositifs de protection comme les
boutons de commande non-métalliques, les isolants,
le dos du coffret, les couvercles ou blindages de réglage
DVM
ECHELLE CA
1.5k ohm
10W
et de compartiment, les réseaux de résistancecapacité, les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suiv ante:
• Brancher le cordon d'alimentation directem-ent à une
0.15 µF
SONDE D'ESSAI
prise de courant de 110-240V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
• A l'aide de deux fils à pinces, brancher une résistance
de 1.5 kΩ 10 watts en parallèle a v ec un condensateur
De nombreuses pièces, électriques et mécaniques, dans
les téléviseurs présentent des caractéristiques spéciales
relatives à la sécurité, qui ne sont souvent pas évidentesà vue. Le degré de protection ne peut pas être
nécessairement augmentée en utilisant des pièces de
remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
3
Page 4
LC-37HV4U
LC-37HV4D
Precautions for using lead-free solder
1 Employing lead-free solder
"PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
L Fa
Indicates lead-free solder of tin, silver and copper.
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend
you to use a dedicated soldering bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit,
contact our service station or ser vice branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remov e the bit from the PWB as soon as you confirm the steady soldering
condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No,★DescriptionCode
ZHNDAi123250EJφ0.3mm250g(1roll)BL
ZHNDAi126500EJφ0.6mm500g(1roll)BK
ZHNDAi12801KEJφ1.0mm1kg(1roll)BM
LCD panel37 Advanced Super View & BLACK TFT LCD
Number of dots3,147,264 dots (1366 768 3dots)
TV
Function
Brightness430 cd/m
Backlight60,000 hours (at Manual Standard position)
Viewing anglesH : 170° V : 170°
Audio amplifier10W 2
SpeakersØ 8cm 2pcs
TerminalsS-VIDEO in, AV in, COMPONENT in
TV-standard (CCIR)
Receiving
Channel
Audio multiplexBTSC System
AVC
System
VHF/UHF
CATV1-125ch
Rear INPUT 1
INPUT 2
American TV Standard NTSC System
VHF 2-13ch, UHF 14-69ch
2
S-VIDEO in, AV in
LC-37HV4U
LC-37HV4D
INPUT 3
ANTENNA 75
Monitor OutAudio (Variable, Fixed), S-VIDEO out, AV out
DC OUTPUT DC6.5V 7W MAX
Front
INPUT 4S-VIDEO, AV in
PC
Headphones
OSD languageEnglish/French/Spanish
Power Requirement
Power
Consumption
Weight
Accessories
AVC System
Display
AVC System
Display
S-VIDEO in, AV in, COMPONENT in, DVI-DIGITAL in
Unbalance, F Type for VHF/UHF/CATV in
15 Pin mini D-Sub, Audio in (Ø 3.5mm jack)
Ø 3.5mm jack
AC 110-240 V, 50/60 Hz
42 W (0.35W Standby with AC 120 V)
144 W (0.4W Standby with AC 120 V)
12.1 lbs./5.5 kg (w/o stand), 12.3 lbs./5.6 kg (with stand)
36.4 lbs./16.5 kg (Display only), 43.9 lbs./19.9 kg (with Display and speakers),
52.9 lbs./24.0 kg (with Display, speakers and stand)
Operation manual ( 1), Remote control unit ( 1), System cable ( 1), AC cord
( 2:LC-30HV4U, x1:LC-37HV4D),“AA” size Alkaline batter
( 1), Speaker (L 1, R 1),
2), RF cable ( 1)
Specifications are subject to change without prior notice.
Speaker screw (
y ( 2), Stand unit
4), Cable clamp (Large
1, Small
5
Page 6
LC-37HV4U
LC-37HV4D
OPERATION MANUAL
How to open the door.
Headphone
(When connecting headphones, the sound from the
speakers is muted.)
PC INPUT terminal (ANALOG RGB)
PC INPUT terminal (AUDIO)
Front view
AVC System
INPUT 4 terminal (S-VIDEO)
INPUT 4 terminal (VIDEO)
INPUT 4 terminals (AUDIO L/R)
CLEAR*
MAIN POWER button
STANDBY/ON indicator
• AV MODE resets to USER
case, press CLEAR, shown in the diagram, lightly with the end of a ballpoint pen or other pointed object.
This will reset the System as shown below.
* If the AVC System is switched on but it does not appear to be operating corr ectly , it may need r esetting. In this
AC INPUT terminal
DISPLAY OUTPUT 1 terminal
DISPLAY OUTPUT 2 terminal
RS-232C
terminal
the near future.)
DC OUTPUT terminal
DVI-DIGITAL
INPUT
terminal
(Terminal for expanded functionality in
Antenna (B)
input terminal
Antenna (A) input terminal
• TV channel returns to initial channel setting (Air:2ch, Cable:1 or 2ch)
• Twin picture resets to normal
NOTE
• Audio setting initializes
• SRS resets to off
• Image position initializes
• Pressing CLEAR will not work if the System is in standby mode (indicator lights red).
Rear view
know it. See page for initializing to the factory preset values when you forget your secret number.
• Pressing CLEAR will not delete channel preset or secret number. See page for clearing the secret number when you
Antenna (A) output
terminal
)
R
, P
B
INPUT 3 COMPONENT
video terminals (Y, P
)
R
, P
B
INPUT 1 COMPONENT
video terminals (Y, P
INPUT 1 terminal (S-VIDEO)
INPUT 3 terminal (S-VIDEO)
INPUT 3 terminals (AUDIO L/R)
INPUT 1 terminal
(VIDEO)
(S-VIDEO)
MONITOR OUTPUT terminal
INPUT 3 terminal (VIDEO)
INPUT 1 terminals
(AUDIO L/R)
INPUT 2 terminals
(AUDIO L/R)
terminal (VIDEO)
MONITOR OUTPUT
MONITOR OUTPUT terminals (AUDIO L/R)
INPUT 2 terminal (VIDEO)
INPUT 2 terminal (S-VIDEO)
Display
Part names
MAIN POWER
button
POWER button
button
INPUT
/ )
/ )
(CH
(VOL
CHANNEL buttons
VOLUME buttons
*OPC: Optical Picture Control
OPC indicator*
POWER indicator
OPC sensor
Remote control sensor
6
Page 7
Hole
Hole
attaching left speaker.
Fasten the screws to secure the
speaker in place.
• Use a screwdriver.
• Per form the same steps for
BulgeBulge
the speaker align with the holes
on the Display.
Take hold of the speaker and
slowly slide it to the Display.
• Make sure that the two bulges of
LC-37HV4U
LC-37HV4D
Attaching the speakers
Preparation
The supplied speaker unit can be attached to or detached from the Display . It must be attached unless you use
external amplifier/speakers.
Before attaching (or detaching) speakers, unplug the AC cord from the AC outlet.
(AV mode: STANDARD,
DYNAMIC, MOVIE, GAME, USER. PC
on or off.
System mode.
1 TV POWER: Switch the Liquid Crystal Television power
2 FRONT SURROUND: Set SRS* and FOCUS* Sound
3 AV MODE:Select an audio or video setting.
Be sure to attach or detach the speakers with two or more people.
123
Example: Attaching right speaker.
mode: STANDARD, USER.)
4 VIEW MODE: Select the screen size.
5 DISPLAY: Display the channel information.
6 SLEEP: Set the sleep timer.
Speaker
plug
/ : Set the volume.
8VOL
9 MENU: Display the menu screen.
10 MENU RETURN: Return to the previous menu screen.
/ / / : Select a desired item on the screen.
11
12 ANT-A/B: Select between ANT-A and B to watch
external mode.
7 FLASHBACK: Return to the previous channel or input
is inserted completely.
Insert the speaker plug into the
terminal on the Display.
• Make sure that the speaker plug
(TV , INPUT 1, INPUT 2, INPUT 3, INPUT 4, PC)
will light. The lighting will turn off if no operations
are performed within about 5 seconds. This button
is used for performing operations in dark places.
13 INPUT: Select a Liquid Crystal T elevision input source.
: When pressed all buttons on the remote control unit
14
broadcasts via the two tuners.
TWIN PICTURE: Set the twin picture mode.
15 MTS: Select the MTS/SAP.
16 CC: Display captions during closed-caption source.
17 TWIN CH buttons
CAUTION
Press again to return to normal
NOTE
terminal or speaker to the Display.
• The speaker ter minals on the Display are only for the supplied speaker unit. Do not connect any third party plug to the
• Do not handle or move the Display by the speakers.
• Perform the same steps for both left and right speakers.
• To detach the speakers, perform the above steps in reverse order.
• You can connect your own amplifier/speakers to the Display. See page 56 for connecting external speakers.
/ : Select the channel of sub screen.
normal screen.
/ : Select the channel.
SELECT: Select the active screen.
SUB INPUT: Select an input source of sub screen.
FREEZE: Set the still image. Press again to return to
screen.
TWIN CH
command of the channel.
18 0 – 9: Set the channel.
19 100 ENT: Select the three digit mode. Execute a
20 CH
21 MUTE: Mute the sound.
22 SET/ENTER: Execute a command.
A, B, C, D: Select four preset favorite channels in four
different categories.
When viewing via ANT-A: up to 16 channels can be
assigned in A, B, C and D.
When viewing via ANT-B: up to 16 channels can be
assigned in A, B, C and D.
With ANT-A and B combined, you can preset up to 32
favorite channels in advance.
23 FAVORITE CH
While watching, you can toggle the selected channels
by pressing A, B, C and D.
24 LED for transmission confirmation
25 Mode switch:
Part names
Remote control unit
2425
12 13
1
14
21
22
SOURCEDTV/SAT
23
INFO
GUIDE
POWER
VOL
DTV/SAT
VCR REC
SET/
ENTER
RECEIVER
FAVORITE CH
INPUT VOL
ABCD
11
POWER
NOTE
• When using the remote control unit, point it at the Liquid
is a trademark of SRS Labs, Inc.
FOCUS technology is incorporated under license from
this page.
*
SRS Labs, Inc.
Crystal Television.
• See pages for operating buttons not listed on
19
ENT
100
20
MENU
DTV/DVD TOP
0
MUTE
FLASHBACK
7
MENU
VOLCH
RETURN
MENU TV/SAT/DVD
8
9
10
EDIT/
SLEEPLEARN
DISPLAY
18
123
456
789
5
6
15
16
17
DVD
/LD
SUB TWIN CH
MTS CC
SELECT
INPUT
/SAT
TV VCRCBL
TV
2
INPUT
/DTV
TWIN
ANT-A/B
FREEZE
PICTURE
SURROUND
FRONT
AV
POWER
VIEW
MODE
MODE
3
4
7
Page 8
LC-37HV4U
LC-37HV4D
Press the two hooks
Display (rear view)
Press down the two
upper hooks to remove
toward the center of the
Display and remove the
cover toward you.
the cover toward you.
DISPLAY INPUT1 DISPLAY INPUT2
(GRAY)
Connect the plug firmly
until the hooks on both
sides click.
(WHITE)
thumb screws.
it by tightening the
Connect the plug into
the terminal and secure
AC cordSystem cable
System cable
AC cord
(GRAY)(WHITE)
Removing the terminal cover
Setting the System
1
After putting the Display and the AVC System in place, connect the system cables and AC cords. Use the
cable clamps for bundling the cables.
Connecting the system cable and the AC cord to the Display
2
AVC System
System cable
If you want to keep a longer distance between
the Display and AVC System, please purchase
the optional system cable AN-07SC1 (about 23
feet/7 meters).
AVC System (rear view)
Connecting the system cable and the AC cord to the AVC System
3
CAUTION
Adjust the screen with both
hands. Put one hand on the
Display and tilt the screen
while steadying the stand
with your other hand.
You can adjust the screen
vertically up to 4 degrees
forward or 6 degrees back-
ward, or rotate 10 degrees
horizontally.
CAUTION
2 inches (5
cm) or more
5 cm or more
5 cm or more
on both sides
Keep enough space
2 inches (5
cm) or more
5 cm or more
5 cm or more
AC CORD CONNECTED.
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT TOUCH UN-INSULATED PARTS OF ANY CABLES WITH THE
There is an exhaust
fan on the right side.
Selecting the location of the System
• Select a place with no direct sunlight and good ventilation.
Where to place the System
Preparation
1
“System” means the Display and AVC System. First select the location where to place the System.
• The Display and the AVC System are connected by the system cable.
Display
10 cm
or more
or more
(10 cm)
4 inches
CAUTION
optional bracket to mount it.
Setting the System in place
Handling the Display
• The Display is very heavy. Move it with two or more people.
Display speakers.
• Do not remove the stand from the Display unless using an
• When moving, put your hands on the Display, but never on the
• Keep enough space above and behind the Display.
CAUTION
Handling the AVC System
• Do not put a VCR or other device on the AVC System.
and the exhaust fan on the right side.
• Keep enough space above and on the sides of the AVC System.
with one, as this can cause overheating and result in malfunction.
• Do not block the ventilation openings on the top and left side,
• Do not spread a thick cloth beneath the AVC System, or cover it
2
8
Page 9
Preparation
4
5
Attaching the clamps and bundling the cables with the clamp
Closing the terminal cover
Cable clamp (Large)
Insert the cable
clamp in the hole
on the Display leg
as shown.
Cable clamp (Small)
Peel off the seal
on the back and
attach as shown.
Display (rear view)
NOTE
• The small clamp on the right is used for
bundling external speakers.
Cables come
out from the
small opening.
Setting the Display on the wall
Setting the AVC System with the stand
CAUTION
• Installing the Liquid Crystal T elevision requir es special skill that should only be performed by qualified service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or
mounting that results in accident or injury.
1
Using an optional bracket to mount the Display
• You can ask a qualified service personnel about using an optional AN-37AG1 bracket to mount the Display
to the wall.
• Carefully read the instructions that come with the bracket before beginning work.
Vertical mountingAngular mounting
Hanging on the wall
AN-37AG1 wall mount bracket. (See the bracket instructions for details.)
How to install the AVC System vertically using the stand unit.
• Use the supplied stand unit for installing the AVC System vertically in an upright position.
Stick each spacer to the
stand as shown.
Peel each spacer
away from the
paper and attach
to the four bulging
areas on the stand.
2
Attach each cushion to
the stand as shown.
3
Fit the stand to the AVC
System.
Peel each cushion
away from the
paper and attach
to the four areas at
the bottom.
Insert the stand into the AVC
System, making sure that the
thick and thin bulges of the
stand align with the big and
small holes on the AVC
System.
Stand
spacer
Bulge
Stand cushion
Thin bulge
Thick
bulge
Big hole
Small
hole
4
Attach the stand using the
stand screws as shown.
Stand screw
The AVC System installed
vertically with the stand.
NOTE
• When mounting the AVC System vertically, always use the supplied stand. Be careful not to block vent holes when
standing up directly on the floor or a flat surface as this can result in equipment failure.
Attaching point
Attaching point
Bulge
LC-37HV4U
LC-37HV4D
9
Page 10
LC-37HV4U
LC-37HV4D
How to connect the speaker cable
Pull up the lid.
Insert the edge of the
cable.
RED BLACKBLACK RED
Put the lid back down.
speakers with clamps as shown above.
• Bundle the cables of the external
CAUTION
specifications.
Incorrect connection may cause a short.
• Make sure external speakers have 8 ohm and 10 watt
• Connect the plus/minus jacks with the correct cables.
Connecting external speakers
Useful adjustment settings
Rear view
Digital TV tuner
S-VIDEO
DVI
AV
Y/PB/PR
B/PR
Y/P
AV
S-VIDEO
AVC System
(rear view)
, ) properly
NOTE
speakers.
• See page 11 for bundling the cables of the exter nal
the speakers.
• Unplug the AC cord from the AC outlet before installing
When using external speakers
• Change the speaker setting to exter nal speakers.
Make sure to connect the speaker jack and cable
AVC System
(front view)
AV Receiver
(Built-in T uner Amp)
AV
AV
S-VIDEOS-VIDEO
Game console/
Camcorder
AV
S-VIDEO
ANALOG RGB
PC-AUDIO
polarity (
• The speaker jacks have plus ( ) and minus ( ) polarity.
• When connecting the left/right speakers, be sure to
connect the plus/minus jacks with the correct cables.
• Plus is red and minus is black.
• The cables are also divided into plus and minus.
VCR
PC
DVD player
Using external equipment
You can connect many types of external equipment to your System, like a DVD player, VCR, Digital TV tuner, PC,
game console and camcorder. To view external source images, select the input source from INPUT on the
remote control unit or on the Display.
10
CAUTION
PC, game console, camcorder or other external equipment.
• To protect all equipment, always turn off the AVC System before connecting to a DVD player, VCR, Digital TV tuner,
NOTE
• Please refer to the relevant operation manual (DVD player, PC, etc.) carefully before making connections.
Page 11
(67 Hz)
LC-37HV4U
LC-37HV4D
PC compatibility chart
Appendix
Remarks
85 Hz
70 Hz
85 Hz
60 Hz
400
640 400
Picture
720
480
640
ResolutionFrequency
Macintosh 13
65 Hz
72 Hz
75 Hz
85 Hz
48060 Hz
848
56 Hz
600
800
60 Hz
72 Hz
Macintosh 16
75 Hz
85 Hz
74.5 Hz
60 Hz
768
624
832
1024
Macintosh 19
70 Hz
75 Hz
85 Hz
60 Hz
768
1280
Audio
102460 Hz
1280
Power control
Apple and Macintosh are registered trademarks
of Apple Computer, Inc.
DDC is a registered trademark of Video Electronics
Standards Association.
Power Management is a registered trademark of
Setup
Sun Microsystems, Inc.
VGA and XGA are registered trademarks of
International Business Machines Co., Inc.
Option
Contrast
Brightness
Red
Green
Blue
Color
Tint
C.M.S.
C.M.S.
Sharpness
Advanced
Color Temp
Black
PC input mode menu items
List of PC menu items to help you with
operations
Picture
Contrast
AV input mode menu items
Basic adjustment settings
List of AV menu items to help you with
operations
Brightness
3D-Y/C
Monochrome
Film Mode
I/P Setting
Audio
Treble
Treble
Bass
Bass
Balance
11
Balance
Speaker
Speaker
Power control
Power Save
Power Save
Power Management
No Signal Off
No Operation Off
Setup
Input Signal
Auto Sync.
Fine Sync.
EZ Setup
CH Setup
Input Signal
Parental CTRL
Picture Flip
Language
Position
Picture Flip
Language
Option
Audio Out
Cool Climate
Input Select
Noise Clean
Audio Out
Cool Climate
Page 12
LC-37HV4U
LC-37HV4D
CONTROL CONTENTS
Response code format
OK
Normal response
Return code (0DH)
ERR
Problem response (communication error or incorrect command)
It input-switches by the toggle. (It is the same as an input change key)
It input-switches to TV. (A channel remains as it is. (Last memory))
It input-switches to INPUT1~INPUT4.
It input-switches to PC.
An input change is also included.
AUTO
(Toggle)
Input terminal number (1–4)
AUTO
*
x
00123
AV-Y/C
_
_
_
1
_________
_________
_________
0x0
PARAMETER
Although it can choose now, it is toggle operation in inside.
COMPONENT
AUTO
AV-Y/C
COMPONENT
DVI
(Toggle)
_
_
_____
_
_
_____
_
_
_____
2
0
Return code (0DH)
ITGD
ITVD
IAVD
IPCD
INP1
INPUT 1
INPUT1-4
PC
INPUT SELECTION B
INP3
INPUT 3
AVMD
AV MODE SELECTION
POWR
TV
CONTROL ITEMCOMMAND
INPUT SELECTION A TOGGLE
POWER SETTINGIt shifts to standby.
Command table
• About the command except being indicated here, it is outside the guarantee range of operation.
STANDARD
DYNAMIC
MOVIE
GAME
12345
90)
10)
PC mode. (
USER
Volume (0–60)
AV mode. (
_
_
_
_
*
*
_
_
*****
*
_
*****
*
VOLM
HPOS
H-POSITIONH-POSITION
VOLUME
POSITION
Stretch [AV]
Normal [PC]
Stretch [PC]
Toggle operation.
(Toggle)
Dot by Dot [PC]
Zoom [PC]
(Toggle)
_
_
_
0
SRSS
SRS
Although it can choose now, it is toggle operation in inside.
90)
20)
60)
30)
Only PC mode. (
(Toggle) [AV]
Side Bar [AV]
S.Stretch [AV]
PC mode. (
AV mode. (
___
_
***
*
*
*
VPOS
V-POSITION
Zoom [AV]
Only PC mode. (
_________
_________
_________
012345678
PHSE
CLCK
WIDE
CLOCK
PHASE
VIEWMODE
Off
___
___
___
123
An input change is included if it is not TV display.
In Air, 2–69ch is effective.
If it is not TV display, it will input-switch to TV.
If it is not TV display, it will input-switch to TV.
In Cable, 1–125ch is effective.
1
1
SRS
The channel number of TV
FOCUS
FOCUS
One screen
Twin screens
The channel number of TV
_________
_
_
_
*
_
_
_
*
_
_
_
*
0
1
4
TWI N
DCCH
DIRECT
TWIN PICTURE
CHANNEL
(1~125)
The channel number of TV
_________
_________
xxx
CHUP
CHDW
CH UP
CH DOWN
CHANNEL
SRS
Change toggle operation of tuner A/B.
Toggle operation of a closed caption.
(Toggle)
(Toggle)
OFF
CC1
CC2T1T2
_
01234
5
ANTS
CLCP
NOTE
ANT-A/B
CC
• If an underbar (_) appears in the parameter column, enter a space.
) in the table is a numerical value, it may write anything.
• If an asterisk (*) appears, enter a value in the range indicated in brackets under CONTROL CONTENTS.
• As long as that from which the parameter (
RS-232C port specifications
Appendix
Command 4-digits:Command. The text of four characters.
Parameter 4-digits:Parameter 0 – 9, x, blank, ?
Return codeCommand 4-digitsParameter 4-digits
1 bit
8 bits
None
9,600 bps
The input signal (PC/AV) can be selected, the volume can be adjusted and various other adjustments and
PC Control of the System
• When a program is set, the Display can be controlled from the PC using the RS-232C terminal.
NOTE
settings can be made, enabling automatic programmed playing.
connections.
Attach an RS-232C cable cross-type (commercially available) to the supplied Din/D-Sub RS-232C for the
•
• This operation system should be used by a person who is accustomed to using computers.
Baud rate:
Communication conditions
Set the RS-232C communications settings on the PC to match the display’s communications conditions.
The Display’s communications settings are as follows:
None
Flow control:
Parity bit:
Data length:
Stop bit:
Eight ASCII codes CR
Communication procedure
Send the control commands from the PC via the RS-232C connector.
The display operates according to the received command and sends a response message to the PC.
Command format
Do not send multiple commands at the same time. Wait until the PC receives the OK response before sending
the next command.
C1 C2 C3 C4 P1 P2 P3 P4
12
Parameter
Input the parameter values, aligning left, and fill with blank(s) for the remainder. (Be sure that 4 values are input for the
parameter.)
0
No problem to input any numerical value for “x” on the table.
When the input parameter is not within an adjustable range, “ERR” returns. (Refer to “Response code format”.)
30
0009
0055
100
?
When “?” is input for some commands, the present setting value responds.
????
Page 13
DIMENSIONS
LC-37HV4U
LC-37HV4D
Display
45/8(117.5)
3217/64(819.6)
2129/64(545)
3721/64(948)
(460.8)
64
/
9
18
45/8(117.5)
Unit: inch/(mm)
(82)
(87.5)
32
/
16
7
12(305)
/
7
3
3
37/16(87.5)
(587)
64
/
7
(697)
16
23
/
7
27
(408.5)
64
/
5
16
4639/64(1184)
77/8(200)
(110)
64
/
21
4
(200)7
8
/
7
7
(183.5)
32
/
7
12(305)2129/64(545)
13
Page 14
LC-37HV4U
LC-37HV4D
REMOVING OF MAJOR PARTS
1.Take off the center and lower terminal covers.
2.Remove the two speaker fixing screws each and the speaker connecting terminal, and take off the speaker.
3.Remove the four stand fixing screws and take off the stand.
4.Remove the 19 cabinets A/B fixing screws and take off the cabinet B.
5.Remove the two key PWB assembly fixing screws and the connector, and take off the key PWB assembly.
6.Remove the key PWB insulating sheet fixing screw and take off the key PWB insulating sheet.
7.Remove the four Main PWB shield fixing screws and take off the Main PWB shield.
8.Remove the four stand angle fixing screws and take off the stand angle.
4
Speaker (right)
2
4
3
1
Terminal cover (center)
Terminal cover (lower)
6
Key PWB insulating sheet
Stand
P152
4
Speaker (left)
2
Key PWB assembly
5
7
P151
Main PWB shield
14
Stand angle
8
Page 15
LC-37HV4U
LC-37HV4D
9.Open six FFC cable holders and remove the three FFC holder (right & left) fixing screws each and all the connectors of flat cables (FFC), and take off the FFC holders (right & left).
10.Remove the Speaker-L and-R PWB fixing screws each and the connectors of them, and take off the Speaker-L
and-R PWBs.
11.Remove the two R/C, LED PWB fixing screws and the connector, and take off the R/C, LED PWB.
12.Remove all the connectors from each PWB.
(Main PWB; 10 points, Power PWB; 5 points, Audio PWB; 3 points, Inver ter -1 PWB 7; points, Inverter -2 PWB; 4
points, Inverter -3 PWB 7; points, and Inverter -4 PWB; 4points.)
9
FFC cable holder (right)
Speaker-R PWB
10
Cable holder
P203
P101
R/C, LED PWB
11
Inverter -1 PWB
CN4101
CN4102
ww
P3811
Cable holder
FFC cable holder (left)
P202
Speaker-L PWB
Inverter -3 PWB
9
10
w
w
w
w
w
P7505
P7506
P7507
P7554
w
CN3701
w
w
CN3782
CN4701
CN3702
CN4702
Power PWB
CN2702
w
SC4603
CN4101
CN7004
CN2004
CN2002
SC4601SC4604
Main PWB
w
Audio PWB
15
SC4602
CN7705
CN2003
w
P3801
w
P3811
w
w
P3802 P3803
w
P7616
P7619
P7618
w
w
w
P7647
P7644
w
Inverter-4 PWBInverter-2 PWB
Page 16
LC-37HV4U
LC-37HV4D
13.Remove the five main PWB fixing screws, and take off the main PWB.
14.Remove the six power PWB fixing screws, and take off the power PWB.
15.Remove the four audio PWB fixing screws, and take off the audio PWB.
16.Take off the inverter-1 PWB.
17.Remove the three inverter-2 PWB fixing screws, and take off the inverter-2 PWB.
18.Take off the inverter-3 PWB.
19.Remove the three inverter-4 PWB fixing screws, and take off the inverter-4 PWB.
20.Remove the two chassis fixing screws and take off the chassis.
13
Inverter-1 PWB
Inverter-2 PWB
17
16
Power PWB
14
Main PWB
Audio PWB
18
Inverter-3 PWB
Inverter-4 PWB
19
15
Chassis
16
20
Page 17
LC-37HV4U
25
24
24
23
22
22
22
22
Reflection panel
Lamp assembly (7 sets)
Lamp holder (top)
Lamp holder (bottom)
Lamp holder (top)
Lamp holder (bottom)
Diffusion sheet
Prism sheet
Reflection/deflection sheet
Sheet angle
Sheet angle
Diffusion panel
Sheet angle
LCD panel unit
LC-37HV4D
• Handling Precautions for LCD Panel
1. Work in a clean room. (Humidity above 50%)
2. Operators should w ear an earthing band.
3. Do not give a shock such as falling and vibration.
4. Use the ionizer. (Within 30 cm)
21.Remove the six LCD panel fixing screws and take off the LCD panel unit.
22.Remove the three sheet angle fixing screws, and take off the sheet angle.
23.Take off the reflection/deflection sheet, prism sheet, diffusion sheet and diffusion panel.
24.Remove the three lamp holders (top & bottom) fixing screws each, and take off the lamp holders (top & bottom).
25.Take off the lamp assembly from the lamp clip.
21
LCD panel unit (front)
21
17
Page 18
LC-37HV4U
LC-37HV4D
ADJUSTMENT PROCEDURES
Though the best adjustment is made at shipment from the factory, the following adjustment is required if the value
should be deviated or some adjustment is needed after replacement of parts.
Display Side:
1. Preparation for Adjustment
The unit needs to be replaced when the AVC System CONFIGROM (IC2202), receiver (IC2206) and HDCP
key ROM (IC2208) are replaced.
Applicable unit: DKEYHB453FE53 (LC-37HV4U)
DKEYHB453FE56 (LC-37HV4D)
2. Adjustment
Enter Adjustment Process mode. → VLSBIAS/15V voltage adjustment →
GRAY level/14.5V voltage adjustment → COMBIAS adjustment → Background adjustment
3. Entry to Adjustment Process mode
(1) For no connection of AVC System:
With the display main power off, while pressing the "INPUT" and "VOL(–)" keys on the display body top
together, turn on the display MAIN POWER. Then, starting is done at DISPLAY process mode.
(2) For connection of AVC System:
With the display main power off, while pressing the "CH (Down)" and "VOL(+)" keys on the display top
together, turn on the Display MAIN POWER. Then, starting is done at DISPLAY process mode.
In both cases of the above (1) & (2), K is displayed on the screen upper left. Then, when some key is
pressed, the first page of DISPLAY ADJUST mode will start.
~ If MAIN POWER is off, the adjustment process mode is released.
4. Key Operation List at Adjustment Process mode
Key
Cursor up
Cursor down
Cursor right
Cursor left
ENTER
INPUT
CH_UP
CH_DOWN
VOL_UP
VOL_DOWN
Function 1 (At page left end)
One item shift to up, Shift to previous
page (At top)
One item shift to down, Shift to next
page (At bottom)
One item shift to right, Page shift (At
initial page)
One item shift to left, Page shift (At
initial page)
Test pattern off
Shift to next page
One item shift to up, Shift to previous
page (At top)
One item shift to down, Shift to next
page (At bottom)
One item shift to right, Page shift/At
initial page
One item shift to left, Page shift (At
initial page)
Function 2 (At value variable)
Adjust value one increase or execution (At
W&R items)
Adjust value one decrease or execution (At
W&R items)
One item shift to right
One item shift to left
Item execution (At W&R items)
Shift to next page
Adjust value one increase or execution (At
W&R items)
Adjust value one decrease or execution (At
W&R items)
One item shift to right
One item shift to left
18
Page 19
5. Adjustment
5-1 VLSBIAS/15V voltage adjustment
Shift to Item of VLS BIAS cursor up/down key, and select the value by cursor right/left key. Connect the
digital voltage meter to MAIN PWB TP4101/No.30 pin of panel gate socket CN4102, and adjust to be
15.00±0.05V by the cursor up/down key.
5-2 GRAY LEVEL/14.5V voltage adjustment
Shift to Item of GRAY LEVEL by cursor up/down key, and select the value by cursor right/left key. Connect
the digital voltage meter to MAIN PWB TP4104/near IC4105, and adjust to be 14.50±0.05V by cursor up/
down key.
This adjustment should be correctly made because this power voltage is a reference voltage of tonal
voltage.
5-3 COMBIAS adjustment
Shift to Item of COMBIAS by cursor up/down key, and select the value by cursor right/left k e y. If the value is
varied by cursor up/down key, the test pattern is made, so adjustment should be made so that the flicker
near the screen center becomes minimum.
5-4 Background adjustment
With AVC center connected, start the set and adjust the display background.
Sequence:
~ Display the screen for adjustment/High-side 200 gradation & Low-side 48 gradation.
~ Adjust ROFFSET, GOFFSET and BOFFSET to allow 200-gradation patterns as a standard.
Adjust the chromaticity of High pattern/screen left to be x=0.273 and y=0.285.
~ Adjust R GAMMA, G GAMMA and B GAMMA to allow 48-gradation patterns as a standard.
Adjust the chromaticity of Low pattern/screen right to be x=0.268 and y=0.267.
LC-37HV4U
LC-37HV4D
The above adjustment can be made in the following method:
~ Adjustment with RS-232C
~ Prepare the personal computer with
WINDOWS95/98/Me/2000/xp inputted and provided with COM port/RS-232C, together with RS-232C
cross cable.
~ Start the set with RS232C cable connected.
~ Start the terminal software. The free ware normally found on the Internet is allowed.
~ The following should be set:
Baud rate 9600
Data 8bits
Parity None
Stop 1bit
Flow control None
~ If they are set correctly, press ENTER key on the personal computer. "ERR" appears atop the ter minal
software.
19
Page 20
LC-37HV4U
LC-37HV4D
~ In this state, enter the command, listed below, and "ENTER" on the keyboard for adjustment.
Press "ENTER" and make sure that "OK" appears on the terminal software.
If "ERR" appears, try again.
Function
Background adjustment started.
R OFFSET value adjusted.
G OFFSET value adjusted.
B OFFSET value adjusted.
R GAMMA value adjusted.
G GAMMA value adjusted.
B GAMMA value adjusted.
R GAMMA table displayed.
G GAMMA table displayed.
B GAMMA table displayed.
Remarks
Adjustment ended at a value other than 1001.
Range: 0000~0256
Range: 0000~0256
Range: 0000~0256
Range: 0020~0180
Range: 0020~0180
Range: 0020~0180
20
Page 21
Lamp error detection
[1] Function
This LCD color TV set is equipped with automatic power-off (lamp error detection) function. This safety
measure serves if the lamp or the lamp circuit gets in trouble.
If by any chance the lamp or the lamp circuit gets in trouble, or if the lamp error detector gets activated for
any other reasons, the following happens.
1 Turn on the power, but it comes off in about 23 seconds. (The power LED indicator at the front of the set
turns from green to red, and it starts flashing in red, repeating on for 250 ms and off for 1 sec.)
2 If the action 1 above occurs 5 times in a row , the power fails to turn on. (The power LED indicator starts
flashing in red, repeating on for 250 ms and off for 1 sec.)
[2] Measures
2-1. Turn off the lamp error detector and check the trouble.
With the "MAIN POWER" s witch off , hold down the "INPUT SELECT" and "VOL UP" keys and press the
"MAIN POWER" switch. Now the "display process mode" (<K> appears onscreen) gets started. Then
press on any key, and Page 1 of "Display adjustment mode" appears onscreen.
In so doing, the lamp and lamp circuit can be checked for anything unusual.
Also look at the 4th line "L ERR RESET" on Page 1 of "Display adjustment mode" to see if the value is
more than 1. If so, it means a lamp error has been detected.
2-2. Reset the lamp error counter.
When the lamp and lamp circuit have been checked for trouble, reset the lamp error counter.
Using the "CURSOR UP/DOWN" key, move the cursor to the 4th line "L ERR RESET" on Page 1 of
"Display adjustment mode". Using the "CURSOR RIGHT/LEFT" k ey, select the value of "L ERR RESET".
Now press the "CURSOR UP/DOWN" key, and the counter will be back to 0.
LC-37HV4U
LC-37HV4D
Display adjustment process Page 1
SERVICE
→GRAYLEVEL
COMBLAS
VLSBLAS
L ERR RESET
LCD
PATTERN
SOUND AND FAN
OTHER
VER M1.~~
Finally do the performance check and make sure no lamp error is detected.
37HV4
076
077
064
5
CEEP3
Individual display-related parameters
Reset to 0
21
Page 22
LC-37HV4U
LC-37HV4D
•List of process adjustment modes (Display)
Process mode contents Page 0LCD Page 1
PATTERN Page 1
SOUND Page 1
Others Page 1
LCD Page 2
LCD Page 3
LCD Page 4
22
Others Page 2
Page 23
Process adjustment list
1st levelPageItemSetting rangeInitial value
Contents1GRAYLEVEL0~255112
COM BIAS0~25587
VLS BIAS0~25541
L ERR RESETZero clear0
PATTERN20~120
R GAMMA20~180 Display only100
R OFFSET0~510 Display only255
G GAMMA20~180 Display only100
G OFFSET0~510 Display only255
B GAMMA20~180 Display only100
B OFFSET0~510 Display only255
SOUND1100HZ0~25592
400HZ0~25596
1KHZ0~255145
4KHZ0~255187
10KHZ0~255187
FAN START0~255224
FAN END0~255230
TEMP ERR0~25555
OTHER1CLR MODE1 digit 0~40
W–
LCD DATA4 digits 0~F–
R/W–
EEPROM7 digits 0~F–
R/W–
SII8616 digits 0~F–
R/W–
2L ERR STOP0~10
MODE0~40
REMOCON0~10
OSTEMP AD0~255AD value
OPC AD0~255AD value
LC-37HV4U
LC-37HV4D
23
Page 24
LC-37HV4U
LC-37HV4D
No image or sound comes out.
TROUBLE SHOOTING TABLE
Is the power LED lit up
in green?
NO
Is the power LED
flashing in red?
YES
Is it flashing once in
one cycle?
NO
Is it flashing twice in
one cycle?
NO
Is it flashing five times
in one cycle?
Is the backlight off?Is "LOSS OF SYNC"
NO
displayed?
YES
Is TP4302 about 0V or
is D4301 off?
YES
YES
Check IC2208 and the circuits
around it.
YES
Is there any problem around pins (104),
(106), (107) and (155) of IC4701, pins
NO
Check the circuits around them.
(104), (106), (107) and (155) of IC4901,
IC4303 and IC4301?
YES
Replace IC4301 and IC4303 or perform
writing to IC4303 and IC4301 using the
special writing jig.
NO
YES
YES
YES
NO
Is the AC cord
NO
normal?
Proceed to "The backlight does
not light up".
Check the power unit.
Check the connections between
the main unit and inverter 3 unit,
between the inverter 3 unit and
inverter 4 unit, and between the
inverter 4 unit and audio unit.
Proceed to "No image
comes out".
Replace the AC cord.
Note that it is necessary to replace the unit when replacing the Config ROM for receiver (IC2202), receiver IC (IC2208) and HDCP key ROM
(IC2208). Have the relevant unit (DKEYHB453FE50) handy.
LED flashing timing list
Error typeLED behavior (1 cycle)
Cable error
AVC-side power error
Lamp error
Monitor power error
AVC temperature error
AVC FAN error
Monitor temperature
error
H: ON
L: OFF
H: ON
L: OFF250ms
H: ON
L: OFF
H: ON
L: OFF
H: ON
L: OFF
H: ON
L: OFF
1S
24
Page 25
TROUBLE SHOOTING TABLE (Continued)
No image comes out.
LC-37HV4U
LC-37HV4D
Is a HIGH appearing
at the RESET terminal
of pin (3) of IC2206?
YES
Is a clock (91.3 MHz)
appearing at TL2201
(pin (102) of IC2206)?
YES
Is a normal sync
signal appearing at
TL2202 (pin (97) of
IC2206), TL2203 (pin
(96) of IC2206) and
TL2204 (pin (95) of
IC2206)?
YES
Check IC4903 and later
ICs (IC4701, IC4702,
IC4901 and IC4902).
Dropout (relating to gray scale)
Set PATTERN1 under
PATTERN on the adjustment
process menu to
gray scale pattern displayed
properly?
YES
"
6071" and "6303" to
Send
LCD DATA under OTHER on
the adjustment process
menu to display the QS drive
test pattern and then send
"
6102". Is the gray scale
displayed properly?
YES
Send "6202" to LCD DATA
under OTHER on the
adjustment process menu. Is
the test pattern displayed
properly at intervals of one
dot?
YES
Send "6203" to LCD DATA
under OTHER on the
adjustment process menu. Is
the test pattern displayed
properly at intervals of one
dot?
YES
Check the connections
between SC2201 and
IC2206, between IC2206 and
IC4701, and between IC2206
and IC4901.
"2"
. Is the
NO
NO
NO
NONO
NO
NO
NO
Check the circuits
around X2201
connected to pin (161)
of IC2206.
Is X2201 connected to pin
(161) of IC2206 oscillating
(18.26MHz)?
YES
Is IC2202 (CONFIG ROM)
operating?
YES
Failure of IC2206
Identify the color signal
presenting a problem in the gray
scale test pattern.
Is there any problem with the
connections and resistances
between IC4501 and SC4601SC4604?
YES
Check IC4501 and
SC4601-SC4604.
Check IC4702, IC4902
and the circuits around
them.
Check the connections
between IC4701 and
IC4501.
Check the connections
between IC4901 and
IC4501.
NO
NO
Check X2201 and the
circuits around it.
Check IC2202 and the
circuits around it.
Check the FFC
connected to SC4601SC4604.
25
Page 26
LC-37HV4U
LC-37HV4D
TROUBLE SHOOTING TABLE (Continued)
Noise appears on the moving image when the QS drive is turned ON.
Is OSTEMP.AD on the 3rd page
of the process adjustment
mode set to 255?
YES
Are the audio unit and the
inverter 4 unit connected
properly by the harness?
YES
Are the inverter 3 unit and the
inverter 4 unit connected
properly by the board-to-board?
YES
Are the main unit and the
inverter 3 unit connected
properly by the harness?
YES
Is the input voltage at pin (2) of
IC2004 (micro-processor) 5V?
YES
Failure of thermistor of TH3801.
The backlight does not light up.
NO
NO
NO
NO
NO
Check IC4701, IC4901 and
the circuits around them.
Check IC4701, IC4901 and
the circuits around them.
Connect securely or replace
the board-to-board.
Connect properly or replace
the harness.
Failure of pin (2) of IC2004
micro-processor
(
)
Is any of the fuses of
F7501-F7504, F7551F7553, F7611-F7614 and
F7641-F7643 burned out?
YES
Check the inverter circuit
downstream from the
burned-out fuse.
NO
Is a control signal
appearing at pin (2)
(OFL1) and pin (3) (OFL2)
of P7506 and P7616?
YES
Is power supplied to each
unit?
YES
Check the wire connected between the inverter 1 and 3 units, the boardto-board between the inverter 1 and 2 units and the board-to-board
between the inverter 3 and 4 units.
Check the opposite
inverter circuit of the pair.
NO
NO
Are the main unit and the inverter
1 and 3 units connected properly
by the harness.
YES
Check the circuits around IC4501
in the main unit and check the
operation of Q7704 and Q7705.
Check for 15V output in the power
unit.
Check the connection of the
high-voltage (pin 2) wire on the
side of the burned-out fuse and
check the connection of the highvoltage (pin 2) wire of the
opposite fluorescent lamp of the
pair.
26
Page 27
TROUBLE SHOOTING TABLE (Continued)
No sound comes out. (Connect to the AVC system and check.)
LC-37HV4U
LC-37HV4D
Is power supplied to each IC
in the audio unit?
YES
Is an audio signal appearing
at pin (8) (L-IN) and pin (10)
(R-IN) of P3802?
YES
Is an audio signal appearing
at pins (10) and (14) of
IC3812 (Audio Output)?
YES
Is an audio signal appearing
at pins (24), (27), (28) and
(31) of IC3812 (Audio
Output)?
YES
Check if RY3801 (for
Internal/External switching) is
operating properly.
NO
NO
NO
NO
Check around the
power regulator circuit
(IC3809, IC3810).
Is an audio signal
appearing at pins (13)
and (20) of SC2202 in
the main unit?
YES
Check around Q2012 and Q2014 and check the
wire connected between the main unit and
audio unit.
Are Q3812 and Q 3813
(MUTE Circuits)
operating?
Check D3828-D3831
for short-circuiting and
check the circuits
around IC3812.
NO
NO
Check for output from the
AVC system side.
Check IC3801, IC3803,
IC3804-IC3807, and
IC3811 for I/O signals.
The whole screen is whitish (LCD power supply)
Disconnect the FFC from CN4101,
CN4102 and CN4601-CN4604.
(Otherwise it may cause the panel to get
broken.)
YES
Check the power supplies.
Check the power supplies to CN4101
and CN4102 in particular.
YES
Is the voltage of R4114 around 6V?
YES
Check the I/O voltages of IC4103,
IC4105 and IC4106.
NO
Check the performance of Q4101
and Q4112 and check the
resistances around IC4102.
27
Page 28
LC-37HV4U
LC-37HV4D
CHASSIS LAYOUT
H
G
F
E
D
C
B
A
87109654321
28
Page 29
LC-37HV4U
LC-37HV4D
29
17161918151413121110
Page 30
LC-37HV4U
P
C
2
U
o
o
t
M
0
m
LC-37HV4D
BLOCK DIAGRAM
H
LCD Back Light
LCD
Monitor
OFL1, 2
R RGB
8X3X2
L RGB
8X3X2
G
OSD RGB
CONF
FLASH
IC4301
F
E
SDRAM (OS_EVEN)
Rewrite
Connector
16 (Data)
IC4702 (A312WJ)
17 (Address, etc)
CONF
CTRL
CPLD
IC4303
(A345WJ)
OS Driver (EVEN)
QFP208pin
(OS_EVEN)
IC4701 (A332WJ)
RGB 8X3
RGB 8X3
LCD Controller
BGA265pin
(LCDCONT)
IC4501 (A475WJ)
CLK
RGB 8X3
OS Driver (ODD)
QFP208pin
(OS_ODD)
IC4901 (A332WJ)
RGB 8X3
OS Driver Control
Dimmer Control, I
16 (Data)
SDRA
IC49
17 (Address, e
D
EEP128K
EEP32K
INITIAL
ROM
HDCP KEY
ROM
DVI Receiver
SII861
QFP208 (TMDS)
IC2206 (SII861)
Rewrite
Connector
OSD Contr
C
B
A
EEP1K
EDID
ROM
DDC
•
TMDS 3X4
•
DDC 6
DVI Connector (24pin)
(TMDS)
SC2201 (ZA017WJ)
TMDS 3X4
• Audio L, R
• Main Correspondence UART
• FLASH Write Control
• Power Control
•
Detection (
• Remote Control Signal for SR
Cable Connection, AVC System Start-up, A
Power Contr
System Connector (
(TMDS)
SC2202 (Z2015C
A
30
87109654321
Page 31
LC-37HV4U
LC-37HV4D
CD Panel
L RGB
8X3X2
Gradation Power
(V0, V64, V96, V128, V160,
V192, V224, V256)
Bias Setting D/A
(GRAYLEVEL)
Gradation Power Bias
COM Control
er Control, Image Control, Test Pattern
6 (Data)
SDRAM (OS_ODD)
IC4902 (A312WJ)
17 (Address, etc)
Thermistor
2
E
PROM
R/C.LEDKEY
OPC
trol
OSD Control
Monitor Micon
(MICON)
IC2004 (3491CE)
Power Control
L, R
Connector (20pin)
(TMDS)
2202 (Z2015CE)
ystem Start-up, AC, Start-up Detection
)
AUDIO
H8
DAC
AUDIO1
IC3802
(M62392M)
Reset
Mute
Sound Processor
(AUDIO1)
IC3803 (CXA1352A)
SRS
AUDIO1
IC3801
(NJM2193M)
F Adjustment
External SP
Tripath AMP
(TA2024++)
ALC
Internal SP
AUDIO2
IC3812
31
17161918151413121110
Page 32
LC-37HV4U
0
LC-37HV4D
OVERALL WIRING DIAGRAM
H
P152P151
G
5
P7506
1
2
1
P7505
F
INVERTER-1 PWB
1
KEY PWB
51
16
QCNW-A966WJZZ
1
1
5
1
CN7704
QCNW-A976WJZZ
QCNW-A481WJZZ
QCNW-A480WJZZ
345
QCNW-A481WJZZ
CN7707
P7507
E
P7508
112
B to B
D
112
14
QCNW-A967WJZZ
QCNW-A975WJZZ
QCNW-A973WJZZ
QCNW-A972WJZZ
7
1
CN2004
8
CN2002
61
QCNW-A969WJZZ
MAIN PWB
QCNW-A965WJZZ
P7555
71
4
CN3701
INVERTER-2 PWB
C
2
P7554
1
1
4
CN3702
CN4701
CN4702
1
3
1
POWER PWB
1
B
R/C, LED PWB
1
5
CN2702
QCNW-A970WJZZ
1
P38
1
P101
8
A
SPEAKER-R PWB
QCNW-A974WJZZ
87109654321
32
Page 33
1
3X Gate Source Driver
Gate Source Driver
2
3X
Gate Source Driver
3
3X
Gate Source Driver
4
3X
5
3X
Gate Source Driver
Gate Source Driver
6
3X
LC-37HV4U
LC-37HV4D
To LCD Panel
B
Z
QCNW-A481WJZZ
QCNW-A480WJZZ
56
CN7705
CN2003
QCNW-A971WJZZ
112
P3802
QCNW-B063WJZZ
2
6
1
12
1
QCNW-A968WJZZ
QCNW-B010WJZZ
QCNW-B088WJZZ
2
1
1
P7616
6
1
P7615
3
14
INVERTER-3 PWB
P7618
1
P7617
B to B
P7645
2
P7647
1
121
121
AUDIO PWB
P3801P3811
3141
INVERTER-4 PWB
2
1
P7644
33
SPEAKER-L PWB
17161918151413121110
Page 34
LC-37HV4U
LC-37HV4D
DESCRIPTION OF SCHEMATIC DIAGRAM
VOLTAGE MEASUREMENT CONDITION:
1. When the exclusive-use AC adapter is used, the colour
bar signal of colour bar generator for service is input to
get the normal screen. When the audio is minimized,
the voltage value is measured with the 20 kΩ/V tester.
WAVEFORM MEASUREMENT CONDITION:
1. When the exclusive-use AC adapter is used, the colour
density, lightness and colour hue are set to the center
position, and the signal of colour bar generator for
service is observed to get waveform.
2. indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)
3. All resistors are Carbon type, unless otherwise noted.
C : SolidW : Cement
S : Oxide FilmT : Special
N : Metal Coating
CAPACITOR
1. All capacitors are mF, unless otherwise noted.
(P=pF=mmF).
2. All capacitors are Ceramic type, unless otherwise
noted.
(ML) : Mylar(TA) : Tantalum
(PF) : Polypro Film(ST) : Styrol
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER2. REF. NO .
3. PART NO.4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order.
Ref. No.Part No.★DescriptionCode
PRINTED WIRING BOARD ASSEMBLIES
å and shaded areas in the Replacement Parts Lists
For location of SHARP Parts Distributor, Please call TollFree; 1-800-BE-SHARP
★ MARK: SPARE PARTS-DELIVERY SECTION
(NOT REPLACEMENT ITEM)
LC-37HV4U
DUNTKB401FE07– MAIN Unit(AVC System)—
DUNTKB493FE07– POWER Unit(AVC System) —
DUNTKB593DE03– FRONT Unit(AVC System) —
DUNTKB594DE03– SR Unit(AVC System)—
DUNTKB658FE01– AV Unit(AVC System)—
CPCi-A005WJ15– PC I/F Unit(AVC System)—
DKEYHB453FE53– MAIN Unit(Display)—
DUNTKB460DE03– AUDIO Unit(Display)—
DUNTKB461DE03– SPEAKER-L Unit(Display)—
DUNTKB462DE03– SPEAKER-R Unit(Display) —
DUNTKB809DE02– INVERTER-1 Unit(Display) —
DUNTKB811DE02– INVERTER-2 Unit(Display) —
DUNTKB810DE02– INVERTER-3 Unit(Display) —
DUNTKB812DE02– INVERTER-4 Unit(Display) —
DUNTKB813DE02– R/C, LED Unit(Display)—
DUNTKB814DE02– KEY Unit(Display)—
RDENCA032WJZZ – POWER Unit(Display)—
LISTE DES PIECES
CHANGE DES PIECES
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les
pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep
éler élee par la marque å et sont hachur élees dans les listes de
pi`eces et dans les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr
éLesente pas les m éoemes caract éLeristiques de s élecurit éle que
la pi`ece recommand élee parl'usine et dans ce manuel de service,
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit r apidement et correctement remplie ,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE2. NO. DE REF
3. NO. DE PIECE4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Canada Limited
Phone (416) 890-2100
★MARQUE: SECTION LIVRAISON DES PIECES DE RECHANGE
Ref. No.Part No.★DescriptionCode
NOTE: This service manual accordingly describes the display
alone. For the entire AVC System, refer to the
LC-30HV4U Service Manual.
LCD PANEL
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
RLCDTA018WJZZJ 37" LCD Panel UnitHG
DUNTKB401FE07– MAIN Unit(AVC System)—
LC-37HV4D
DUNTKB493FE08– POWER Unit(AVC System) —
DUNTKB593DE03– FRONT Unit(AVC System) —
DUNTKB594DE03– SR Unit(AVC System)—
DUNTKB658FE02– AV Unit(AVC System)—
CPCi-A005WJ17– PC I/F Unit(AVC System)—
DKEYHB453FE56– MAIN Unit(Display)—
DUNTKB460DE05– AUDIO Unit(Display)—
DUNTKB461DE05– SPEAKER-L Unit(Display)—
DUNTKB462DE05– SPEAKER-R Unit(Display) —
DUNTKB809DE04– INVERTER-1 Unit(Display) —
DUNTKB811DE04– INVERTER-2 Unit(Display) —
DUNTKB810DE04– INVERTER-3 Unit(Display) —
DUNTKB812DE04– INVERTER-4 Unit(Display) —
DUNTKB813DE04– R/C, LED Unit(Display)—
DUNTKB814DE04– KEY Unit(Display)—
RDENCA041WJZZ – POWER Unit(Display)—
R2001 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2002 VRS-CY1JF562JY J 5.6k 1/16W Metal Oxide AA
R2003 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2004 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R2005 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R2006 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R2007 VRS-CY1JF222JY J 2.2k 1/16W Metal Oxide AA
R2008 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2009 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2010 VRS-CY1JF683JY J 68k 1/16W Metal Oxide AA
R2011 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R2012 VRS-CA1JF333JY J 33k 1/16W Metal Oxide AA
R2013 VRS-CY1JF394JY J 390k 1/16W Metal Oxide AA
R2014 VRS-CY1JF105JY J 1M 1/16W Metal Oxide AA
R2015 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2016 VRS-CY1JF106JY J 10M 1/16W Metal Oxide AA
R2017 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2018 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2019 VRS-CY1JF272JY J 2.7k 1/16W Metal Oxide AA
R2020 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R2021 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2023 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2026 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2027 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2028 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2029 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2030 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2032 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2033 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2034 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2035 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2037 VRS-CY1JF393JY J 39k 1/16W Metal Oxide AA
R2038 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2039 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2040 VRS-CY1JF333JY J 33k 1/16W Metal Oxide AA
R2041 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2042 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2043 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R2044 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2045 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2046 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2047 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2050 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2051 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2052 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2053 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2054 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R2055 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R2056 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R2057 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2058 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2073 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2076 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2077 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2078 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2079 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2080 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2081 VRS-CY1JF123JY J 12k 1/16W Metal Oxide AA
R2082 VRS-CY1JF153JY J 15k 1/16W Metal Oxide AA
R2083 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2085 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2086 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2091 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2092 VRS-TQ2BD222JY J 2.2k 1/8WMetal Oxide AA
R2093 VRS-CY1JF123JY J 12k 1/16W Metal Oxide AA
R2094 VRS-CY1JF153JY J 15k 1/16W Metal Oxide AA
R2095 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2096 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2097 VRS-TQ2BD222JY J 2.2k 1/8WMetal Oxide AA
R2098 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2099 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2201 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2202 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2203 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2204 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2205 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R2206 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2209 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2210 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2212 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2213 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2214 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2215 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2216 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2217 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2218 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2219 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2220 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2221 VRS-CY1JF822FY J 8.2k 1/16W Metal Oxide AA
R2222 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2224 VRS-CY1JF222FY J 2.2k 1/16W Metal Oxide AA
R2227 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2228 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2229 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2230 VRS-CY1JF473FY J 47k 1/16W Metal Oxide AA
R2231 VRS-CY1JF473FY J 47k 1/16W Metal Oxide AA
R2232 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2233 VRS-CY1JF100FY J 101/16W Metal Oxide AB
R2234 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2235 VRS-CY1JF100FY J 101/16W Metal Oxide AB
R2237 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R2238 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R2239 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R2240 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2241 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R2242 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R2243 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R2244 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2245 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R2246 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2247 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2248 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2249 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2251 VRS-CY1JF221JY J 220 1/16W Metal Oxide AA
R2252 VRS-CY1JF221JY J 220 1/16W Metal Oxide AA
R2253 VRS-CY1JF221JY J 220 1/16W Metal Oxide AA
R2254 VRS-CY1JF221JY J 220 1/16W Metal Oxide AA
R2256 VRK-CD1JJ680JYJ 681/16W Metal Comp. AC
R2257 VRK-CD1JJ680JYJ 681/16W Metal Comp. AC
R2258 VRS-CB1JF680JY J 681/16W Metal Oxide AA
R2259 VRS-CA1JF680JY J 681/16W Metal Oxide AA
R2260 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2261 VRS-CY1JF391JY J 390 1/16W Metal Oxide AA
R2262 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R2264 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2265 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2266 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2267 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2268 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2269 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2270 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2272 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2273 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2274 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2275 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2276 VRS-CY1JF152JY J 1.5k 1/16W Metal Oxide AA
R2278 VRS-CY1JF332JY J 3.3k 1/16W Metal Oxide AA
R2279 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2281 VRK-CD1JJ680JYJ 681/16W Metal Comp. AC
R2282 VRS-CB1JF680JY J 681/16W Metal Oxide AA
R2283 VRS-CA1JF680JY J 681/16W Metal Oxide AA
R2284 VRK-CD1JJ680JYJ 681/16W Metal Comp. AC
R2285 VRS-CA1JF680JY J 681/16W Metal Oxide AA
R2286 VRS-CB1JF680JY J 681/16W Metal Oxide AA
R2287 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2288 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2289 VRS-CY1JF223JY J 22k 1/16W Metal Oxide AA
R2291 VRS-CA1JF680JY J 681/16W Metal Oxide AA
R2292 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R2293 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R2294 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2295 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R2296 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R2297 VRS-CY1JF473JY J 47k 1/16W Metal Oxide AA
R4101 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4102 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4103 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4104 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4106 VRS-CY1JF273FY J 27k 1/16W Metal Oxide AA
R4107 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4108 VRS-CY1JF561FY J 560 1/16W Metal Oxide AA
R4109 VRS-CY1JF621FY J 620 1/16W Metal Oxide AA
R4110 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4111 VRS-CY1JF273FY J 27k 1/16W Metal Oxide AA
R4112 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4113 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4114 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4115 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4117 VRS-CY1JF333FY J 33k 1/16W Metal Oxide AA
R4118 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4119 VRS-CY1JF470FY J 471/16W Metal Oxide AA
R4120 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4121 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4122 VRS-CY1JF682FY J 6.8k 1/16W Metal Oxide AA
R4123 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4124 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4125 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4126 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4129 VRS-CY1JF433FY J 43k 1/16W Metal Oxide AA
R4130 VRS-CY1JF913FY J 91k 1/16W Metal Oxide AA
R4131 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4132 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4133 VRS-CY1JF562FY J 5.6k 1/16W Metal Oxide AA
R4134 VRS-CY1JF132FY J 1.3k 1/16W Metal Oxide AA
R4135 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4136 VRS-TW2ED331JY J 330 1/4WMetal Oxide AB
R4137 VRS-CY1JF561FY J 560 1/16W Metal Oxide AA
R4138 VRS-CY1JF161FY J 160 1/16W Metal Oxide AA
R4139 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4140 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4141 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4142 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4143 VRS-CY1JF153FY J 15k 1/16W Metal Oxide AA
R4144 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4145 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4146 VRS-CY1JF682FY J 6.8k 1/16W Metal Oxide AA
R4147 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R4148 VRS-CY1JF100FY J 101/16W Metal Oxide AB
R4149 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4150 VRS-CY1JF393FY J 39k 1/16W Metal Oxide AA
R4151 VRS-CY1JF113FY J 11k 1/16W Metal Oxide AA
R4152 VRS-CY1JF821FY J 820 1/16W Metal Oxide AA
R4153 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4155 VRS-CY1JF562FY J 5.6k 1/16W Metal Oxide AA
R4156 VRS-CY1JF433FY J 43k 1/16W Metal Oxide AA
R4157 VRS-CY1JF911FY J 910 1/16W Metal Oxide AA
R4158 VRS-CY1JF681FY J 680 1/16W Metal Oxide AA
R4159 VRS-CY1JF363FY J 36k 1/16W Metal Oxide AA
R4160 VRS-CY1JF103FY J 10k 1/16W Metal Oxide AA
R4161 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4162 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4163 VRS-CY1JF393FY J 39k 1/16W Metal Oxide AA
R4164 VRS-CY1JF163FY J 16k 1/16W Metal Oxide AA
R4165 VRS-CY1JF101FY J 100 1/16W Metal Oxide AD
R4166 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4167 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4168 VRS-CY1JF133FY J 13k 1/16W Metal Oxide AA
R4169 VRS-CY1JF363FY J 36k 1/16W Metal Oxide AA
R4170 VRS-CY1JF391FY J 390 1/16W Metal Oxide AA
R4171 VRS-CY1JF333FY J 33k 1/16W Metal Oxide AA
R4172 VRS-CY1JF163FY J 16k 1/16W Metal Oxide AA
R4173 VRS-CY1JF431FY J 430 1/16W Metal Oxide AA
R4174 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4175 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4176 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4177 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4178 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4179 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4180 VRS-CY1JF163FY J 16k 1/16W Metal Oxide AA
R4181 VRS-CY1JF273FY J 27k 1/16W Metal Oxide AA
R4182 VRS-CY1JF621FY J 620 1/16W Metal Oxide AA
R4183 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4184 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4185 VRS-CY1JF273FY J 27k 1/16W Metal Oxide AA
R4186 VRS-CY1JF683FY J 68k 1/16W Metal Oxide AA
R4187 VRS-CY1JF222FY J 2.2k 1/16W Metal Oxide AA
R4188 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4189 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4190 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4191 VRS-CY1JF393FY J 39k 1/16W Metal Oxide AA
R4192 VRS-CY1JF620JY J 621/16W Metal Oxide AA
R4193 VRS-CY1JF102JY J 1k1/16W Metal Oxide AA
R4194 VRS-CY1JF121JY J 120 1/16W Metal Oxide AA
R4195 VRS-CY1JF183FY J 18k 1/16W Metal Oxide AA
R4196 VRS-CY1JF203FY J 20k 1/16W Metal Oxide AA
R4197 VRS-CY1JF103FY J 10k 1/16W Metal Oxide AA
R4198 VRS-CY1JF562FY J 5.6k 1/16W Metal Oxide AA
R4199 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4200 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4201 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4202 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4203 VRS-CY1JF433FY J 43k 1/16W Metal Oxide AA
R4204 VRS-CY1JF683FY J 68k 1/16W Metal Oxide AA
R4205 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4206 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R4207 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4208 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4209 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4210 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4211 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4212 VRS-TV1JD102JY J 1k1/16W Metal Oxide AA
R4213 VRS-CY1JF131FY J 130 1/16W Metal Oxide AA
R4214 VRS-CY1JF222FY J 2.2k 1/16W Metal Oxide AA
R4215 VRS-CY1JF750FY J 751/16W Metal Oxide AA
R4216 VRS-CY1JF105FY J 1M 1/16W Metal Oxide AA
R4217 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4218 VRS-CY1JF393FY J 39k 1/16W Metal Oxide AA
R4219 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4220 VRS-CY1JF105FY J 1M 1/16W Metal Oxide AA
R4221 VRS-TX2HF472JY J 4.7k 1/2WMetal Oxide AB
R4222 VRS-TX2HF272JY J 2.7k 1/2WMetal Oxide AA
R4223 RR-NZ0027TAZZY J
R4224 VRS-TV1JD222JY J 2.2k 1/16W Metal Oxide AA
R4225 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4226 VRS-TV1JD222JY J 2.2k 1/16W Metal Oxide AA
R4227 VRS-TW2ED821JY J 820 1/4WMetal Oxide AB
R4228 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4229 VRS-CY1JF105FY J 1M 1/16W Metal Oxide AA
R4230 VRS-CY1JF202FY J 2.0k 1/16W Metal Oxide AA
R4231 VRS-CY1JF563JY J 56k 1/16W Metal Oxide AA
R4232 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4233 VRS-CY1JF393FY J 39k 1/16W Metal Oxide AA
R4234 VRS-CY1JF154FY J 150k 1/16W Metal Oxide AA
R4235 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4236 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4237 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4238 VRS-CY1JF105JY J 1M 1/16W Metal Oxide AA
R4240 VRS-CY1JF242JY J 2.4k 1/16W Metal Oxide AA
R4241 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4242 VRS-CY1JF222JY J 2.2k 1/16W Metal Oxide AA
R4243 VRS-CY1JF153JY J 15k 1/16W Metal Oxide AA
R4245 VRS-CY1JF332JY J 3.3k 1/16W Metal Oxide AA
R4246 VRS-CY1JF912FY J 9.1k 1/16W Metal Oxide AA
R4247 VRS-CY1JF301FY J 300 1/16W Metal Oxide AA
R4248 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R4249 VRS-CB1JF000JY J 01/16W Metal Oxide AC
R4250 VRS-CB1JF000JY J 01/16W Metal Oxide AC
R4253 VRS-CA1JF000JY J 01/16W Metal Oxide AB
R4256 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4257 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4258 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4260 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4261 VRS-TW2ED101JY J 100 1/4WMetal Oxide AA
R4262 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4263 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4264 VRS-TW2ED101JY J 100 1/4WMetal Oxide AA
R4265 VRS-CY1JF681FY J 680 1/16W Metal Oxide AA
R4266 VRS-CY1JF273FY J 27k 1/16W Metal Oxide AA
R4267 VRS-CY1JF163FY J 16k 1/16W Metal Oxide AA
R4268 VRS-CY1JF330JY J 331/16W Metal Oxide AA
R4269 VRS-CY1JF100JY J 101/16W Metal Oxide AA
R4270 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4271 VRS-CY1JF202FY J 2.0k 1/16W Metal Oxide AA
R4272 VRS-CY1JF243FY J 24k 1/16W Metal Oxide AA
R4273 VRS-CY1JF104JY J 100k 1/16W Metal Oxide AA
R4274 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4301 VRS-CB1JF103JY J 10k 1/16W Metal Oxide AA
R4302 VRS-CB1JF103JY J 10k 1/16W Metal Oxide AA
R4303 VRS-CA1JF103JY J 10k 1/16W Metal Oxide AA
R4304 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4305 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4306 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4307 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4308 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4309 VRS-TV1JD331JY J 330 1/16W Metal Oxide AB
R4310 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R4311 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R4312 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4313 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4314 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4315 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4316 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4317 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R4501 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4502 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4503 VRS-CB1JF101JY J 100 1/16W Metal Oxide AA
R4504 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R4505 VRS-CA1JF101JY J 100 1/16W Metal Oxide AA
R4506 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4507 VRS-CA1JF472JY J 4.7k 1/16W Metal Oxide AA
R4508 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4509 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4510 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4511 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4512 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4513 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4514 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4515 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4516 VRS-CA1JF330JY J 331/16W Metal Oxide AC
R4517 VRS-CA1JF330JY J 331/16W Metal Oxide AC
R4518 VRS-CB1JF330JY J 331/16W Metal Oxide AC
R4519 VRS-CB1JF330JY J 331/16W Metal Oxide AC
R4520 VRS-CB1JF330JY J 331/16W Metal Oxide AC
R4521 VRS-CA1JF330JY J 331/16W Metal Oxide AC
R4522 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4523 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4524 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4525 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4526 VRK-CD1JJ330JYJ 331/16W Metal Comp. AC
R4527 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4528 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4529 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4601 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4602 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4603 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4604 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4605 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4606 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4607 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4608 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4609 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4610 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4611 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4612 VRK-CD1JJ100JYJ 101/16W Metal Comp. AC
R4613 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4614 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4615 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R4616 VRS-CY1JF220JY J 221/16W Metal Oxide AA
R4701 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4702 VRS-CA1JF472JY J 4.7k 1/16W Metal Oxide AA
R4703 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4704 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4705 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4707 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4709 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4711 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4712 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4713 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4714 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4715 VRS-CB1JF390JY J 391/16W Metal Oxide AA
R4716 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4717 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4718 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4719 VRS-CB1JF390JY J 391/16W Metal Oxide AA
R4720 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4721 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4901 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4902 VRS-CA1JF472JY J 4.7k 1/16W Metal Oxide AA
R4903 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4904 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4905 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4907 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4909 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4911 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide AA
R4915 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4916 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4917 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4918 VRS-CB1JF390JY J 391/16W Metal Oxide AA
R4919 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4920 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4921 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4922 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4923 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R4924 VRK-CD1JJ390JYJ 391/16W Metal Comp. AC
R4925 VRS-CB1JF390JY J 391/16W Metal Oxide AA
R4929 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R4930 VRS-CY1JF000JY J 01/16W Metal Oxide AA
R7703 VRS-TW2ED330JY J 331/4WMetal Oxide AA
R7705 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R7706 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R7707 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R7708 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R7711 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R7713 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R7714 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R7715 VRS-CY1JF101JY J 100 1/16W Metal Oxide AA
R7716 VRS-CY1JF302FY J 3.0k 1/16W Metal Oxide AA
R7717 VRS-CY1JF102FY J 1k1/16W Metal Oxide AA
R7718 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R7719 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R7720 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R7721 VRS-CY1JF243FY J 24k 1/16W Metal Oxide AA
R7722 VRS-CY1JF682FY J 6.8k 1/16W Metal Oxide AA
R7723 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R7724 VRS-CY1JF103JY J 10k 1/16W Metal Oxide AA
R7725 VRS-CY1JF332FY J 3.3k 1/16W Metal Oxide AA
R7726 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7727 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7728 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7729 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7730 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7731 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R7732 VRS-TV1JD000JY J 01/16W Metal Oxide AA
R3801 VRS-TW2ED000JY J 01/4WMetal Oxide AB
R3804 VRS-TX2HF000JY J 01/2WMetal Oxide AB
R3805 VRS-CY1JF222JY J 2.2k 1/16W Metal Oxide AA
R3806 VRS-CY1JF183JY J 18k 1/16W Metal Oxide AA
100
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.