Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the
safety and performance of the set.
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
Page 2
LC-32LE265T / LC-40LE265T
i
SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
WARNING
1. For continued safety, no modification of any circuit should be
attempted.
2. Disconnect AC power before servicing.
BEFORE RETURNING THE RECEIVER (Fire &
Shock Hazard)
Before returning the receiver to the user, perform the following
safety checks:
3. Inspect all lead dress to make certain that leads are not pinched,
and check that hardware is not lodged between the chassis and
other metal parts in the receiver.
4. Inspect all protective devices such as non-metallic control knobs,
insulation materials, cabinet backs, adjustment and compartment
covers or shields, isolation resistor-capacitor networks, mechanical
insulators, etc.
5. To be sure that no shock hazard exists, check for leakage current in
the following manner.
• Plug the AC cord directly into a 110-240 volt AC outlet.
• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15 F capacitor in series with all exposed metal cabinet
parts and a known earth ground, such as electrical conduit or electrical ground connected to an earth ground.
• Use an AC voltmeter having
with 5000 ohm per volt, or higher, sen-
sitivity or measure the AC voltage drop across the resistor.
• Connect the resistor connection to all exposed metal parts having a
return to the chassis (antenna, metal cabinet, screw heads, knobs
and control shafts, escutcheon, etc.) and measure the AC voltage
drop across the resistor.
All checks must be repeated with the AC cord plug connection
reversed. (If necessary, a nonpolarized adaptor plug must be used
only for the purpose of completing these checks.)
Any reading of 0.74 Vrms (this corresponds to 0.5 mA rms AC.) or
more is excessive and indicates a potential shock hazard which
must be corrected before returning the monitor to the owner.
Many electrical and mechanical parts in LCD colour television have
special safety-related characteristics.
These characteristics are often not evident from visual inspection, nor
can protection afforded by them be necessarily increased by using
replacement components rated for higher voltage, wattage, etc.
Replacement parts which have these special safety characteristics are
identified in this manual; electrical components having such features
are identified by "" and shaded areas in the Replacement Parts List
and Schematic Diagrams.
For continued protection, replacement parts must be identical to those
used in the original circuit.
The use of a substitute replacement parts which do not have the same
safety characteristics as the factory recommended replacement parts
shown in this service manual, may create shock, fire or other hazards.
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the
servicing guidelines which follow:
DVM
AC SCALE
1.5k ohm
10W
TO EXPOSED
METAL PARTS
CONNECT TO
KNOWN EARTH
GROUND
0.15µF
TEST PROBE
Page 3
LC-32LE265T / LC-40LE265T
ii
PRECAUTION FOR USING LEAD-FREE SOLDER
PRECAUTIONSFORUSINGLEAD-FREESOLDER
Employing lead-free solder
• “PWBs” of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the PWBs and service manuals. The
alphabetical character following LF shows the type oflead-free solder.
Example:
Using lead-free wire solder
• When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional lead wire solder may cause damage or accident due to cracks.
As the melting point oflead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40 C, we recommend you to use a dedicated soldering
bit, if you are not familiar with how to obtain lead-free wire solder or soldering bit, contact our service station or service branch in your area.
Soldering
• As the melting point oflead-free solder (Sn-Ag-Cu) is about 220 C which is higher than the conventional lead solder by 40 C, and as it has poor
solder wettability, you may be apt to keep the soldering bit in contact with the PWB for extended period of time. However, Since the land may be
peeled off or the maximum heat-resistance temperature of parts may be exceeded, remove the bit from the PWB as soon as you confirm the
steady soldering condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on and off the power of the bit as
required.
If a different type of solder stays on the tip of the soldering bit, it is alloyed with lead-free solder. Clean the bit after every use ofit.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
• Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Indicates lead-free solder of tin, silver and copper.Indicates lead-free solder of tin, silver and copper.
Ref No. Part No. ĞƐĐƌŝƉƟŽŶ
DKEYMG567FM01 MAIN hŶŝƚ
RDENCA474WJPZ Power UŶŝt
DUNTKG463FM01 LED/IR hŶit
RUNTKB281WJZZ LED Bar (A)
RUNTKB282WJZZ LED Bar (B)
32LE265T
Ref No. Part No. ĞƐĐƌŝƉƟŽŶ
DKEYMG567FM02 MAIN hŶŝƚ
DUNTKG409FM02 Power UŶŝt
DUNTKG463FM01 LED/IR hŶit
RUNTKB283WJZZ LED Bar (A)
RUNTKB284WJZZ LED Bar (B)
The HDMI 3 and INPUT 6 terminals can both use the same audio input terminal.
• As a part of policy of continuous improvement, SHARP reserves the right to make design and specifi cation changes for
product improvement without prior notice. The performance specifi cation fi gures indicated are nominal values of production
units. There may be some deviations from these values in individual units.
CAUTION
• Installing the Liquid Crystal Television requires special skill that should only be performed by qualifi ed service personnel.
Customers should not attempt to do the work themselves. SHARP bears no responsibility for improper mounting or mounting
that results in accident or injury.
• Carefully read the instructions that come with the bracket before beginning work.
Page 6
LC-32LE265T / LC-40LE265T
2 – 1
CHAPTER 2. OPERATION MANUAL
[1] OPERATION MANUAL
TV (Front)
POWER indicator
Light offPower off.
Lighted (Red)The TV is in standby mode.
Lighted (Green)The TV is on.
• The illustrations used throughout this manual are based on LC-40LE265T.
TV (Rear)
AIR
CABLE
POWER
3
6
AUDIO IN
ANALOGUE
RGB (PC)
ARC
RS-232C IOIOI
6
INPUT 6
1
INPUT 1
DIGI
TAL
AUDIO
OUTPUT
4
INPUT 4
5
INPUT 5
AUDIO OUT
R - AUDIO - L
R -
AUDIO - L
R -
AUDIO - L
VIDEO/Y
P
B
(C
B
)
P
R
(C
R
)
COMPONENT/AV INPUT
VIDEO
5
8
9
6
7
15
14
13
101112
USB 1
DC5V 1.5A
DC5V 0.9A
MHL
2
3
2
1
3
4
1 USB 1 terminal
2 INPUT 2 (HDMI/MHL) terminal
3 Headphone jack (
3.5 mm)
• The speakers do not output volume when
headphones are plugged in.
8 AUDIO IN terminal
9 Antenna terminal (AIR/CABLE)
10 AUDIO OUT terminals
11 INPUT 5 terminals
12 INPUT 4 terminals
13 RS-232C terminal
14 POWER (On/Off) button
15 Keypad control
Keypad control
JOG-KEY
BASIC
FUNCTION
FUNCTION
DURING MENU
r
CH UP
r
*
s
CH DOWN
s
*
+
VOL UP
+
*
–
VOL DOWN
–
*
b
(BELOW 1 SEC)
INPUTSELECT/ENTER
b
(1 SEC
AND OVER)
MENU
RETURN/MENU
EXIT
* Repeat keys
*
1
The INPUT 3 and INPUT 6 terminals can both use the same analogue audio input terminal. However, the proper item must be
selected in the “Audio select” menu. (See page 9.)
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.
• The illustrations used throughout this manual are based on LC-40LE265T.
Page 7
LC-32LE265T / LC-40LE265T
2 – 2
Part names and functions
Remote control unit
HDMI
1
2
5
7
8
9
11
6
3
4
12
13
14
15
16
17
18
10
19
20
21
9 a/b/c/d (Cursor)
Select a desired item on the setting screen.
確定
(ENTER)
Execute a command.
10 電視 (TV)
Press to access analogue and digital TV mode.
11 紅/綠/黃/藍 (R/G/Y/B) (Colour) buttons
The coloured buttons are correspondingly used to select
the coloured items on the screen.
12 ECO
Reduce overall power consumption based on user
preferences.
13
色彩調整 (靜止
) [(COLOUR ADJ.) (FREEZE)]
Freeze a motion picture on the screen and adjust the
colour tone of the still image.
14 照片 (PHOTO)
Display your pictures directly on the TV screen.
15
入
(INPUT) (INPUT SOURCE)
Select an input source.
16 頻道 r/s (CHr/s)
TV input mode: Select the channel.
(
頻道
r
) Increase the channel number.
(
頻道
s
) Decrease the channel number.
17 目錄 (MENU)
Display the menu screen.
18
音頻切換
(MPX)
Select the sound multiplex mode.
19 返回 (RETURN)
MENU mode: Return to the previous menu screen.
20
節目表
(EPG)
DTV mode: To display EPG (Electronic Programme Guide)
screen.
指南
(GUIDE)
DTV mode: Display the programme channel list.
資訊
(INFO)
DTV mode: Display the programme information.
(See page 10.)
收音機
(RADIO)
Press to access RADIO mode.
21 字幕 (SUBTITLE)
Switch subtitle languages on/off.
1
電源
(POWER) (STANDBY/ON)
To switch the power on and off.
2
定時關機
(SLEEP)
Set the Sleep timer.
0 hr. 30 min.1 hr. 00 min.
2 hr. 30 min.
1 hr. 30 min.
2 hr. 00 min.
Off
3 HDMI
Select the HDMI input mode.
4 0 – 9
Set the channel.
5 A (Flashback)
Press A to return to the previous selected channel or
external input mode.
6
螢幕顯示
(DISPLAY)
Display the channel or input information.
7
音量
k/l (VOLk/l)
Set the volume.
(
音量
k
) Increase the volume.
(
音量
l
) Decrease the volume.
8 e (Mute)
Press e s Mutes sound.
Press e again s Restores sound.
Mute will be cancelled after 30 minutes. However, the TV
will not suddenly output loud sound as the volume level
will be set to 0 automatically. Increase the volume level by
pressing
音量
k
(VOLk).
Page 8
LC-32LE265T / LC-40LE265T
3 – 1
CHAPTER 3. ADJUSTMENT
[1] ADJUSTMENT ( LC-40LE265T )
[1] ADJUSTMENT PROCEDURE
1.Entering and cancel the adjustment process mode
1)While holding down the POWER and CENTER keys at the same time,plug in
the AC cord to turn the power.
2).Backlight turned ON,screen disply show Black pattern and LED blinking GREEN --> RED -->
GREEN -->RED.
3)Enter password “UP ( CH UP )-->DOWN (CH DOWN )--> UP (CH UP )”. (After 30 sec password not
keyed in or password keyed in wrong, go to previous Power Status (On,Stand by or OFF ).
4).Backlight turned On , screen display show Purple test pattern ( LED still blinking GREEN -->
RED -->GREEN --> RED )
5).Press the Center Key . ( The adjustment process mode screen appears. )
6).After run function, LED light to GREEN.
7).To cancel it, turn o the power using the POWER switch or remote control .
2.Remote controller Key operation and description of disply in adjustment process mode.
1.Key Operation
Remote controller Key JOY Key &ƵŶĐƟŽŶ
CH ( / )
-Changing channel (UP/DOWN)
VOL ( + / - )
-Changing volume (UP/DOWN)
Cursor ( / )
UP/DOWN Turning a page (PREVIOUS /NEXT)
Cursor ( / )
LEFT/RIGHTChanging a selected line ƐĞƫŶŐ (+10 /-10 )
INPUT ďƵƩŽŶ or remote
controller
CENTER
Input source switching (toggle switching )
(ATV --> AV -->Component -->PC RGB )
ENTER- Enter
* Input mode is switched ĂƵƚŽŵĂƟĐĂůLJ when relevant adjustment is started so far as the ŶĞĐĞƐƐĂƌLJ input signal is available .
Page 9
LC-32LE265T / LC-40LE265T
3 – 2
3. Software upgrading.
1) Plug off the LCD TV.
2) Insert the USB device to the USB terminal at the LCD TV.
(Make sure that the latest software is installed in the USB device).
3) Hold the LCD TV power key and plug on the LCD TV.
Programmable memory IC is used for Digital V-com adjustment in this model. INX provide Auto Vcom tools to
adjust Digital V-com. Below items is suggested to be ready before Digital V-com adjustment in customer LCM
line.
a. USB Sensor Board.
b. Programmable software.
c. Document: Auto V-com adjustment suggestion OI.
STEP
1: Sensor board setting as shown in below.
Page 11
LC-32LE265T / LC-40LE265T
3 – 4
STEP 2: Connect SCL, SDA, and GND between PC and panel module
VGA
PCA/D BoardPCBI
DVI
LVDS(I/F)
Sensor board
USB
7 PINS
STEP 3: Send the correct flicker pattern (refer to CMI product SPEC)
Page 12
LC-32LE265T / LC-40LE265T
3 – 5
STEP 4: Execute the program of Auto VCOM
STEP 5: Put the sensor board on the center of the panel and press “Start” button
Page 13
LC-32LE265T / LC-40LE265T
3 – 6
1. MAIN SOFTWARE PACKAGE
egakcaP erawtfoS ledoM
LC-40LE265T WISTERIA_TAIWAN_Pack23_vXXX.bin
Main Software Filename : XXX is Software version
If any changes of software, will be informed by MARUHEN.
2. SIGNAL ADJUSTMENT
A) PICTURE ADJUSTMENT
Confirmation of signal from generator (setting to spec level)
PAL Composite signal ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
15K Component signal (50Hz) ˖Y level ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
Pb, Pr level ˖0.7Vp-p ˖0.7Vp-p f 0.02Vp-p
33K Component signal ˖Y level ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
Pb, Pr level ˖0.7Vp-p ˖0.7Vp-p f 0.02Vp-Com
(1) Adjustment Mode
ERUDECORP NOITIDNOC METI
1 Adjustment Mode Press the test key at the test remote control
(2) Component 15K 50Hz Signal Adjustment (COMP-SD)
ERUDECORP NOITIDNOC METI
1 Setting [Signal]
COMP 15K 50Hz
(576i)
100% Full-field
Colour Bar
[Terminal]
COMPONENT
INPUT 4
ί
Feed the COMPONENT 15K 50Hz (576i) 100% Full-field
Colour Bar signal(100% colour saturation) to
COMPONENT INPUT 4
2 Auto Adjustment Test Mode page 4
(COMP SD)
At the related page, move cursor to [COMP SD ADJ], press
ENTER.
[OK] appears when finished.
100% White
ėĕ
Black
Page 14
LC-32LE265T / LC-40LE265T
3 – 7
(3) Component 33K 60Hz Signal Adjustment (COMP-HD)
ERUDECORP NOITIDNOC METI
1 Setting [Signal]
COMP 33K 60Hz
(1080i)
100% Full-field
Colour Bar
[Terminal]
COMPONENT
INPUT 4
ί
Feed the COMPONENT 33K 60Hz (1080i) 100% Full-field
Colour Bar signal(100% colour saturation) to
COMPONENT INPUT4
2 Auto Adjustment Test Mode page 5
(COMP HD)
At the related page, move cursor to [COMP HD ADJ], press
ENTER.
[OK] appears when finished.
(4) PC (ANALOG RGB) Signal Adjustment (PC-RGB)
NO. ERUDECORP NOITIDNOC METI
1Setting[Signal]
XGA 60Hz
100% Checkered
Pattern
[Terminal]
PC INPUT 6
ί
Feed the XGA 60Hz 100% Checkered pattern
signal(100% colour saturation) to PC INPUT
䯲
Please make sure SYNC is OFF.
2Auto Adjustment Test Mode page 6
(PC-RGB)
At the related page, move cursor to [RGB ADJ], press
ENTER.
[OK] appears when finished.
100% WhiteėĕBlack
Page 15
LC-32LE265T / LC-40LE265T
3 – 8
B) WHITE BALANCE ADJUSTMENT
a) White Balance Adjustment
NO.
ITEM ERUDECORP NOITIDNOC
1Setting Backlight : MAX
AV Mode :
DYNAMIC
Active Backlight :
OFF
Set the luminance
meter on the
centre of the
screen
For the details of white balance adjustment procedure, please refer to white
balance
adjustment spec for Kameyama model.
1. Confirm the set condition.
2. Connect the white balance jig.
3. Through RS-232C command, adjustment mode screen is displayed.
2Auto
Adjustment
[command]
Adjustment
Mode
KRSW0001
KKT10037
Setting
KYOF0001
OSDS0001
SBSL0016
Multi point
adj. Mode
MSET0000
WBI20255
Point 2
WBI20229
MG2G****
MG2B****
MG2R****
Point 1
WBI10040
MG1G****
MG1B****
MG1R****
Write
MSET0003
Set
Max.Level
Initial setting
C
nt
= 5000:1
WB
MAX
= 4080
WB
H
= 3664/4080
WB
L
= 640/4080
(1) Measurement MAX Brightness
(2) Set MIN Brightness
(3) Measurement HIGH Brightness
(4) Measurement LOW Brightness
(5) Calculation H Ȗ
(6) Calculation LȖ
(7) Calculation HIGH luminance (Ȗ=2.2)
(8) Calculation Initial setting of R/G/B_HIGH
(9) Set Initial setting of R/G/B_HIGH
(10) Original WB adjustment is performed (HIGH)
Set the specified gradation for point 2, fix the
most faint colour to get reference value,
adjust others 2 colours to minus adjustment for
reference value of point 2.
(11) Measurement HIGH Brightness
(Set) R_HIGH= G_HIGH
G_HIGH= G_HIGH
B_HIGH= G_HIGH
(12) Calculation MAX luminance after WB
ADJ set to Ȗ=2.2 (L
XHG
)
(13) Set R/G/B_MAX
(14) Calculation LOW luminance (Ȗ=2.2)
(15) Calculation Initial setting of R/G/B_LOW
(16) Set Initial setting of R/G/
B_LOW
(17) Original WB adjustment is performed (LOW).
Set the specified gradation for point 1. Set G of
point 1 to the default value [(R1 x G value
of point 2/R2), with fractions rounded] and
adjust RB to the reference value of point 1.
L
max
=305.7 cd/m²
L
min
= L
max/Cnt
= 0.102
L
XH
=235.1 cd/m²
L
XL
=2.06 cd/m²
HȖ=LOG((L
XH
-L
min
)/(L
max-Lmin
))/
LOG(WB
H
/WB
MAX
)= 2.44
LȖ =LOG((L
XL
-L
min
)/(L
max-Lmin
))/
LOG(WB
L
/WB
MAX
)=2.73
L
H22
=(L
max-Lmin
) x
(WB
H
/WB
MAX
)^2.2+L
min
=241.31
WB
HX
=WB
MAX
X ((L
H22
-L
min
)/(L
max-Lmin
))^
(1/H Ȗ)=3703
R_HIGH=WB
HX
’=3703
G_HIGH=WB
HX
’=3703
B_HIGH=WB
HX
’=3703
R_HIGH=3702
G_HIGH=3641
B_HIGH=3703
R_HIGH=3641
G_HIGH=3641
L
XHG
=
231.3
B_HIGH=3641
L
XMX=LXHG
/((W
B
H
/WB
MAX
)^2.2)=293.04
R_MAX=G_MAX*(R_HIGH/G_HIGH)=4078
G_MAX=WB
MAX
X ((L
XMX
-L
min
)/(L
max
-
L
min
))^(1/HȖ)=4010
B_MAX=G_MAX*(B_HIGH/G_HIGH)=4078
L
XLX
=(L
XMX
-L
min
) x (WBL/WB
MAX
)^2.2+L
min
=5.08
WB
LX
=WB
MAX
X ((L
XLX
-L
min
)/(L
max
-
L
min
))^(1/LȖ)=901
R_LOW=WB
XLX
=901
Example: G6 panel also use
for G8/ CSOT, CMI (be careful
of INT setting)
RESULT
Page 16
LC-32LE265T / LC-40LE265T
3 – 9
MGMG****
MGMR****
MGMB****
(18) Adjusted value is writing at [command]
MSET0003
(19) Set the G of point Max. to the default value
(4080 x G value of point 2 / R2). Set the R,B
Max. value [G
max
– G value of point 2 + (R,B
value of point 2)
(20) Calculate the slope R2
slope,
G2
slope,
B2
slope
between MAX and Point2. R2
slope =
(R
max
- R
high
)/(4080- 3664 )
(21) Calculate the correction value پR
high,
پG
high, پBhigh.
R
high = R2slope X
(3840 - 3664)
(22)
Set the reference value R,G,B of point 2
(R2’)=R2+پR
high
(23) Calculate the slope R1
slope,
G1
slope,
B1
slope
between Point2 and Point1. R1
slope =
(R
high
- R
low
)/ (3664 -640)
(24) Calculate the correction value پR
low,
پG
low, پBlow.
پR
low = R1slope X
(717-640)
(25)
Set the reference value R,G,B of point 1
(R1’)=R1+پR
low
(26) Shut down the AC power.
䯲
Initial value at RGB 2 point :3664
䯲
Initial value at RGB 1 point : 640
[Adjustment value]
侀
Teaching set send by engineering dept is set as
reference.
[Reference values for adjustment reference]
Equipment : Luminance meter [Minolta CA-210]
Level
Spec
Data
Adjustmen
t Spec.
Inspection
Spec.
Point
2 ref.
values
229 x=0.2685
y=0.2670
0.0010 0.0020
Point
1 ref.
values
40
x=0.2685
y=0.2670
0.0045 0.0090
Ref. : For inspection, set the LCD TV as below.
AV MODE : [DYNAMIC] (Reset)
Aging Time : Minimum 30 minutes
G_LOW=WB
XLX=901
B_LOW=WB
XLX=901
R_LOW= 921
G_LOW=901
B_LOW=971
RESULT
Page 17
LC-32LE265T / LC-40LE265T
3 – 10
4. FACTORY SETTING
AC power is plug off after shipment setting is done.
Caution: Do not plug on again after shipment setting is done. If do, please re-do the shipment setting. Do not off
with remote control.
Model Name Factory Setting Key
Name
Remote Control
Code
S-System Setting OSD Language
Settin
g
A3KLJ2XVET
T-Set tin g
100000111111110M
TRADITIONAL
CHINESE/
ENGLISH
ERUDECORP NOITIDNOC METI
Factory setting AC power off to exit
the factory setting.
1. Setting is done with test remote control.
2. Press the ‘Factory Setting’ key on the remote control continuously.
3. When Green background appears on screen and ‘K’ mark
disappears, setting is completed.
The followings are initialised to factory setting
1) User setting
2) Channel data (e.g. broadcast frequencies)
3) Manufacturer’s option settings
4) Password data
5) Setting values are set based on model destination
Page 18
LC-32LE265T / LC-40LE265T
3 – 11
[2] ADJUSTMENT ( LC-32LE265T )
[1] ADJUSTMENT PROCEDURE
1.Entering and cancel the adjustment process mode
1)While holding down the POWER and CENTER keys at the same time,plug in
the AC cord to turn the power.
2).Backlight turned ON,screen disply show Black pattern and LED blinking GREEN --> RED -->
GREEN -->RED.
3)Enter password “UP ( CH UP )-->DOWN (CH DOWN )--> UP (CH UP )”. (After 30 sec password not
keyed in or password keyed in wrong, go to previous Power Status (On,Stand by or OFF ).
4).Backlight turned On , screen display show Purple test pattern ( LED still blinking GREEN -->
RED -->GREEN --> RED )
5).Press the Center Key . ( The adjustment process mode screen appears. )
6).After run function, LED light to GREEN.
7).To cancel it, turn o the power using the POWER switch or remote control .
2.Remote controller Key operation and description of disply in adjustment process mode.
1.Key Operation
Remote controller Key JOY Key &ƵŶĐƟŽŶ
CH ( / )
-Changing channel (UP/DOWN)
VOL ( + / - )
-Changing volume (UP/DOWN)
Cursor ( / )
UP/DOWN Turning a page (PREVIOUS /NEXT)
Cursor ( / )
LEFT/RIGHTChanging a selected line ƐĞƫŶŐ (+10 /-10 )
INPUT ďƵƩŽŶ or remote
controller
CENTER
Input source switching (toggle switching )
(ATV --> AV -->Component -->PC RGB )
ENTER- Enter
* Input mode is switched ĂƵƚŽŵĂƟĐĂůLJ when relevant adjustment is started so far as the ŶĞĐĞƐƐĂƌLJ input signal is available .
Page 19
LC-32LE265T / LC-40LE265T
3 – 12
3. Software upgrading.
1) Plug off the LCD TV.
2) Insert the USB device to the USB terminal at the LCD TV.
(Make sure that the latest software is installed in the USB device).
3) Hold the LCD TV power key and plug on the LCD TV.
If any changes of software, will be informed by MARUHEN.
2. SIGNAL ADJUSTMENT
A) PICTURE ADJUSTMENT
Confirmation of signal from generator (setting to spec level)
PAL Composite signal ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
15K Component signal (50Hz) ˖Y level ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
Pb, Pr level ˖0.7Vp-p ˖0.7Vp-p f 0.02Vp-p
33K Component signal ˖Y level ˖0.7Vp-p f 0.02Vp-p (pedestal to white level)
Pb, Pr level ˖0.
7Vp-p ˖0.7Vp-p f 0.02Vp-Com
(1) Adjustment Mode
ERUDECORP NOITIDNOC METI
1 Adjustment Mode Press the test key at the test remote control
(2) Component 15K 50Hz Signal Adjustment (COMP-SD)
ERUDECORP NOITIDNOC METI
1 Setting [Signal]
COMP 15K 50Hz
(576i)
100% Full-field
Colour Bar
[Terminal]
COMPONENT
INPUT 4
ί
Feed the COMPONENT 15K 50Hz (576i) 100% Full-field
Colour Bar signal(100% colour saturation) to
COMPONENT INPUT 4
2 Auto Adjustment Test Mode page 4
(COMP SD)
At the related page, move cursor to [COMP SD ADJ], press
ENTER.
[OK] appears when finished.
100% WhiteėĕBlack
Page 21
LC-32LE265T / LC-40LE265T
3 – 14
(3) Component 33K 60Hz Signal Adjustment (COMP-HD)
ERUDECORP NOITIDNOC METI
1 Setting [Signal]
COMP 33K 60Hz
(1080i)
100% Full-field
Colour Bar
[Terminal]
COMPONENT
INPUT 4
ί
Feed the COMPONENT 33K 60Hz (1080i) 100% Full-field
Colour Bar signal(100% colour saturation) to
COMPONENT INPUT4
2 Auto Adjustment Test Mode page 5
(COMP HD)
At the related page, move cursor to [COMP HD ADJ], press
ENTER.
[OK] appears when finished.
(4) PC (ANALOG RGB) Signal Adjustment (PC-RGB)
NO. ERUDECORP NOITIDNOC METI
1Setting[Signal]
XGA 60Hz
100% Checkered
Pattern
[Terminal]
PC INPUT 6
ί
Feed the XGA 60Hz 100% Checkered pattern
signal(100% colour saturation) to PC INPUT
䯲
Please make sure SYNC is OFF.
2Auto Adjustment Test Mode page 6
(PC-RGB)
At the related page, move cursor to [RGB ADJ], press
ENTER.
[OK] appears when finished.
100% WhiteėĕBlack
Page 22
LC-32LE265T / LC-40LE265T
3 – 15
B) WHITE BALANCE ADJUSTMENT
a) White Balance Adjustment
NO.
ITEM ERUDECORP NOITIDNOC
1Setting Backlight : MAX
AV Mode :
DYNAMIC
Active Backlight :
OFF
Set the luminance
meter on the
centre of the
screen
For the details of white balance adjustment procedure, please refer to white
balance
adjustment spec for Kameyama model.
1. Confirm the set condition.
2. Connect the white balance jig.
3. Through RS-232C command, adjustment mode screen is displayed.
2Auto
Adjustment
[command]
Adjustment
Mode
KRSW0001
KKT10037
Setting
KYOF0001
OSDS0001
SBSL0016
Multi point
adj. Mode
MSET0000
WBI20255
Point 2
WBI20229
MG2G****
MG2B****
MG2R****
Point 1
WBI10040
MG1G****
MG1B****
MG1R****
Write
MSET0003
Initial setting
C
nt
= 5000:1
WB
MAX
= 4080
WB
H
= 3664/4080
WB
L
= 640/4080
(1) Measurement MAX Brightness
(2) Set MIN Brightness
(3) Measurement HIGH Brightness
(4) Measurement LOW Brightness
(5) Calculation H Ȗ
(6) Calculation LȖ
(7) Calculation HIGH luminance (Ȗ=2.2)
(8) Calculation Initial setting of R/G/B_HIGH
(9) Set Initial setting of R/G/B_HIGH
(10) Original WB adjustment is performed (HIGH)
Set the specified gradation for point 2, fix the
most faint colour to get reference val
ue,
adjust others 2 colours to minus adjustment for
reference value of point 2.
(11) Measurement HIGH Brightness
(Set) R_HIGH= G_HIGH
G_HIGH= G_HIGH
B_HIGH= G_HIGH
(12) Calculation MAX luminance after WB
ADJ set to Ȗ=2.2 (L
XHG
)
(13) Set R/G/B_MAX
(14) Calculation LOW luminance (Ȗ=2.2)
(15) Calculation Initial setting of R/G/B_LOW
(16) Set Initial setting of R/G/
B_LOW
(17) Original WB adjustment is performed (LOW).
Set the specified gradation for point 1. Set G of
point 1 to the default value [(R1 x G value
L
max
=305.7 cd/m²
L
min
= L
max/Cnt
= 0.102
L
XH
=235.1 cd/m²
L
XL
=2.06 cd/m²
HȖ=LOG((L
XH
-L
min
)/(L
max-Lmin
))/
LOG(WB
H
/WB
MAX
)= 2.44
LȖ =LOG((L
XL
-L
min
)/(L
max-Lmin
))/
LOG(WB
L
/WB
MAX
)=2.73
L
H22
=(L
max-Lmin
) x
(WB
H
/WB
MAX
)^2.2+L
min
=241.31
WB
HX
=WB
MAX
X ((L
H22
-L
min
)/(L
max-Lmin
))^
(1/H Ȗ)=3703
R_HIGH=WB
HX
’=3703
G_HIGH=WB
HX
’=3703
B_HIGH=WB
HX
’=3703
R
_HIGH=3702
G_HIGH=3641
B_HIGH=3703
R_HIGH=3641
G_HIGH=3641
L
XHG
=
231.3
B_HIGH=3641
L
XMX=LXHG
/((W
B
H
/WB
MAX
)^2.2)=293.04
R_MAX=G_MAX*(R_HIGH/G_HIGH)=4078
G_MAX=WB
MAX
X ((L
XMX
-L
min
)/(L
max
-
L
min
))^(1/HȖ)=4010
B_MAX=G_MAX*(B_HIGH/G_HIGH)=4078
L
XLX
=(L
XMX
-L
min
) x (WBL/WB
MAX
)^2.2+L
min
=5.08
WB
LX
=WB
MAX
X ((L
XLX
-L
min
)/(L
max
-
L
min
))^(1/LȖ)=901
Example: G6 panel also use
for G8/ CSOT, CMI (be careful
of INT setting)
RESULT
Page 23
LC-32LE265T / LC-40LE265T
3 – 16
Set
Max.Level
MGMG****
MGMR****
MGMB****
of point 2/R2), with fractions rounded] and
adjust RB to the reference value of point 1.
(18) Adjusted value is writing at [command]
MSET0003
(19) Set the G of point Max. to the default value
(4080 x G value of point 2 / R2). Set the R,B
Max. value [G
max
– G value of point 2 + (R,B
value of point 2)
(20) Calculate the slope R2
slope,
G2
slope,
B2
slope
between MAX and Point2. R2
slope =
(R
max
- R
high
)/(4080- 3664 )
(21) Cal
culate the correction value پR
high,
پG
high, پBhigh.
R
high = R2slope X
(3840 - 3664)
(22)
Set the reference value R,G,B of point 2
(R2’)=R2+پR
high
(23) Calculate the slope R1
slope,
G1
slope,
B1
slope
between Point2 and Point1. R1
slope =
(R
high
- R
low
)/ (3664 -640)
)
(24) Calculate the correction value پR
low,
پG
low, پBlow.
پR
low = R1slope X
(717-640)
(25) Set the reference value R,G,B of point 1
(R1’)=R1+پR
low
(26) Shut down the AC power.
䯲
Initial value at RGB 2 point :3664
䯲
Initial value at RGB 1 point : 640
[Adju
stment value]
侀
Teaching set send by engineering dept is set as
reference.
[Reference values for adjustment reference]
Equipment : Luminance meter [Minolta CA-210]
Level
Spec
Data
Adjustmen
t Spec.
Inspection
Spec.
Point
2 ref.
values
229
x=0.270
y=0.265
0.0010 0.0020
Point
1 ref.
values
40
x=0.270
y=0.265
0.0045 0.0090
Ref. : For inspection, set the LCD TV as below.
AV MODE : [DYNAMIC] (Reset)
Aging Time : Minimum 30 minutes
R_LOW=WB
XLX
=901
G_LOW=WB
XLX
=901
B_LOW=WB
XLX
=901
R_LOW= 921
G_LOW=901
B_LOW=971
RESULT
Page 24
LC-32LE265T / LC-40LE265T
3 – 17
5. FACTORY SETTING
AC power is plug off after shipment setting is done.
Caution: Do not plug on again after shipment setting is done. If do, please re-do the shipment setting. Do not off
with remote control.
Model Name Factory Setting Key
Name
Remote Control
Code
S-System Setting OSD Language
Setting
A3KLG2XSET
T-SETTING
10000 1111 1111
10
MTRADISIONAL
CHINESE/
ENGLISH
ERUDECORP NOITIDNOC METI
Factory setting AC power off to exit
the factory setting.
1. Setting is done with test remote control.
2. Press the ‘Factory Setting’ key on the remote control continuously.
3. When Green background appears on screen and ‘K’ mark
disappears, setting is completed.
The followings are initialised to factory setting
1) User setting
2) Channel data (e.g. broadcast frequencies)
3) Manufacturer’s option settings
4) Password data
5) Setting values are set based on model destination
Page 25
LC-32LE265T / LC-40LE265T
3 – 18
[3] USB CLONE SPECIFICATIONS
[3] USB Clone (Smart Loader)
1. Description
The Smart Loader is a function implemented in the service software to easily replicate the user settings of one TV into another.
These settings include (but not restricted to): picture and audio, turning set-up, language and country selection, PIN, child locked programs etc.
Factory adjustments are not copied as they are different for every TV.
The Smart Loader makes possible the user data to be stored in a memory device connected to the USB terminal of the TV that is used as reference
and later load those data into other TVs by using their respective USB terminal.
2. How it works
1. Enter USB clone menu (Smart Loader)
i) Repeat 1 to 4 in “Entering and cancel the adjustment process mode ”
iii) Enter digit “369” then it will go to Smart Loader Menu
2. Smart Loader function
i) SMLD Store
• To copy all related data from TV -> USB and put under a fixed filename “SHP_SMLD.bin” (8kB).
ii) SMLD Restore
• To restore the related data from USB -> TV.
iii) SMLD Store and Restore execution
• To execute SMLD Store or SMLD Restore, highlight at selected item and press Enter.
• When copying is in process, “WAIT” is displayed.
• After cloning process is done, “OK” is displayed.
If cloning process is not finished due to error (e.g. no pendrive detected), “NG” is displayed.
3. Exit USB Clone menu (Smart Loader)
i) To exit Smart Loader menu, plug
off AC Cord.
---
Smart Loader
SMLD Store[]
SMLD Restore[]
SMLD StoreSMLD Restore
2nd AQUOS TVUSB1st AQUOS TV
ii) Press [UP] Key,it will go to password entry OSD.
Page 26
LC-32LE265T / LC-40LE265T
3 – 19
[4] PUBLIC MODE SETTING PROCEDURE
[4] PUBLIC MODE SETTING PROCEDURE
1. How to start Public Mode
• There are the following two ways to get the public mode setup screen displayed.
2) Press the “RIGHT” keys on the set.
3) Get the password input screen displayed.
4) The 3-digit password is now verified.
The password [0] [2] [7] provides for the public mode screen. (This screen comes on with whatever adjustment process settings.)
With any other passwords, the screen changes to the normal mode.
2. How to exit Public Mode
There are the following ways to quit the public mode setup screen.
• Turn off “PUBLIC MODE” in the adjustment process mode. () m This way alone is not for quitting the setup screen, but for quitting the mode by
itself.
• Turn off the power with the “POWER” key. ()
• Select “EXECUTE”.()
xxx “PUBLIC MODE” stays on in the adjustment process mode.
xxx The settings will be back to the factory ones.
3. Public Mode Setting Values
• With the factory settings made, the public mode settings get initialized. (The adjustment process remains intact.)
Procedure
• The input starts with the leftmost digit.
• Use the numeric keys [1] thru [9] and [10/0] keys on the remote controller.
The other keys are not acceptable.
• With a numeric-key input, “–” will change to “ “. The input position will move one digit to the right.
• With all the 3 digits entered, the password will be verified.
1) Repeat steps 1 to 4 in Entering and cancel the adjustment process mode .
Page 27
LC-32LE265T / LC-40LE265T
3 – 20
4.Public Mode Menu
The guidance is not displayed onscreen .
Setup procedure
To move the cursor up and down ,use the "cursor UP/DOWN Key (remote controller )and "CH (UP )/(DOWN )"Key (remote controller and set ).
To change the ƐĞƫŶŐƐƵƐĞ the "cursor RIGHT/LEFT "Key (remote controller )and (RIGHT /LEFT) local key.
To save new ƐĞƫŶŐƐŬĞĞƉ the cursor at"Exucute"and use the "cursor RIGHT/LEFT"Key (remote controller )
VARIABLE : "POWER/RECEPTION"Key on TV unit or remote control is enabled.
FIXED_ALL : "POWER/RECEPTION"Key on TV unit or remote control is disabled.
FIXED_BODYKEY : Only the "MAIN POWER"Key on TV unit is disabled ( The remote control is enabled )
RC RESPOND : The main unit's POWER switch toggles between ON and standby ( the same ŽƉĞƌĂƟŽŶ by
the remote control ).
OFF TIMER (SLEEP) (*Only when ƐĞƫŶŐ to FIXED_ALL )
KƉƟŽŶ
Default
Key disabled when set
When ƐĞůĞĐƟŶŐ to Η&/yͺ>>ΗĨƵŶĐƟŽŶ related standby factors (see below ) doesn't work ,and not ƐĞůĞĐƟŶŐ
OFF TIMER (Sleep)
No ŽƉĞƌĂƟŽŶ OFF
No signal OFF (including the power management )
These items does not exist according to the model .
If the power is pressed in the ordinary more in ƐĞƫŶŐ to "FIXED_ALL" and "FIXED_BODYKEY",the ĐĂƵƟŽŶ is displayed for 5 seconds.
When power ďƵƩŽŶ on the main unit is pressed When power ďƵƩŽŶ on R/C is pressed
other than default
Remark
2.SHUT DOWN MODE
This ĨƵŶĐƟŽŶ decides wheather scanning digital tuner is enable or disabled when the power is standby.
džƉůĂŶĂƟŽŶ
No Power Žī by power ďƵƩŽŶ .No Power Žī by remote control.
KƉƟŽŶ
"NORMAL " or "QUICK"
LAMRONtluafeD
NORMAL : Scanning digital tuner is enabled when power is standby.
QUICK : Scanning digital tuner is disable.
It is possible to put into the standby state instantaneously due to power Žī input,when the
power is standby.
Immediately,state is a complete standby.
In ƐĞůĞĐƟŶŐ "QUICK",the ĨƵŶĐƟŽŶ does not work for the following items ;ƐĞůĞĐƟŽŶ impossible .)
ON TIMER ,QUICK START ,DIGITAL FIXED ,etc.
*These items does not exist acording to the model .
Remarks
Page 28
LC-32LE265T / LC-40LE265T
3 – 21
3.MAXIMUM VOLUME
4.VOLUME FIXED
Default
AC CTRL : The unit stars at the volume ƐƉĞĐŝĮĞĚ in the volume ĮdžĞĚ level,when power is
AC/RC CTRL : The unit starts at the volume ƐƉĞĐŝĮĞĚ in the volume ĮdžĞĚ level ,when power is
( AC JON,remote control JON,main unit's Key JON )
In "Variable" ƐĞƫŶŐ ,the ƐŽƵŶĚ volume ŚĂĚ been ĐŽŶǀĞŶƟŽŶĂůůLJ set at 1 but this ŽƉĞƌĂƟŽŶ has been
ĂďŽůŝƐŚĞĚ;ĂŶĚ follow the last memory ).
The ƐŽƵŶĚ volume form the ON-ƟŵĞ is not set at 1 either ĂŶĚ the ƐŽƵŶĚ volume set value of the
ON-ƟŵĞƌ before the hotel ŵŽĚĞ is ĞdžĞĐƵƚĞĚ .
^ĞƫŶŐ is ǀĂůŝĚ only for the speakers of the unit.(As for the ŚĞĂĚƉŚŽŶĞƚŚĞƐŽƵŶĚ volume can be set up to 60
ŝƌƌĞƐƉĞĐƟǀĞ of the limit. )
In line output ;ƐŽƵŶĚ volume variable ),the ƐŽƵŶĚ volume can be ĂĚũƵƐƚĞĚ from -60 to 0 ŝƌƌĞƐƉĞĐƟǀĞ of
pre-ĂĚũƵƐƚĞĚ value.
As for ƐŽƵŶĚ volume ĮdžŝŶŐ ĂŶĚ ƐŽƵŶĚ volume MAX level,the ƐŽƵŶĚ volume ĮdžŝŶŐ has priority.
Once the ƐŽƵŶĚ volume has been ĐŚĂŶŐĞĚ by ĂĚũƵƐƚŵĞŶƚ process or ŚĞĂĚƉŚŽŶĞŝƚ shoul be set back to the ƐŽƵŶĚ
volume preset by ƐŽƵŶĚ volume ĮdžŝŶŐ level when the ĂĚũƵƐƚŵĞŶƚ process
ĞŶĚƐ or when the ŚĞĂĚƉŚŽŶĞ is ƌĞŵŽǀĞĚ
5.VOLUME FIXED LEVEL
6.R/C BUTTON
Limit in ƐĞƫŶŐ
džĐĞƉƟŽŶ
In the item "VOLUME" of ĂĚũƵƐƚŵĞŶƚ process ,the ƐŽƵŶĚ volume can be set freely ŝƌƌĞƐƉĞĐƟǀĞ of this ƐĞƫŶŐ .
When the ƐŽƵŶĚ volume is set lower than 99,only ĮŐƵƌĞƐ are ĚŝƐƉůĂLJĞĚĂŶĚ the ƐŽƵŶĚ volume bar is not ĚŝƐƉůĂLJĞĚ
The ŵĂdžŝŵƵŵƐŽƵŶĚ volume for ON-ƟŵĞƌ (WAKE UP TIMER)is ůŝŵŝƚĞĚ also to the preset value.
^ĞůĞĐƟŽŶ
Default
džƉůĂŶĂƟŽŶ
^ŽƵŶĚ volume not be ĂĚũƵƐƚĞĚ ŚŝŐŚĞƌ than the preset value.
100
ĚũƵƐƚŵĞŶƚ from 1 to 100 (no loop )
FIXED : The volume is ĮdžĞĚ to the value ĂĚũƵƐƚĞĚ in the volume ĮdžĞĚ level .
ƚƵƌŶĞĚ on in the case of the AC-ON only.
ƚƵƌŶĞĚ on any case .
džƉůĂŶĂƟŽŶ
Remark
^ĞƫŶŐ is ǀĂůŝĚ only for the speakers of the unit .(As for the ŚĞĂĚƉŚŽŶĞƚŚĞƐŽƵŶĚ volume can be set up to 100
ŝƌƌĞƐƉĞĐƟǀĞ of the limit.)
In line output ;ƐŽƵŶĚ volume variable ),the ƐŽƵŶĚ volume can be ĂĚũƵƐƚĞĚ from-100 to 0 ŝƌƌĞƐƉĞĐƟǀĞ of pre-ĂĚũƵƐƚĞĚ
value.
When
the ƐŽƵŶĚ volume is set ŚŝŐŚĞƌ than the MAX ƐĞƫŶŐ by the ĂĚũƵƐƟŶŐ process or ŚĞĂĚƉŚŽŶĞ ,the ƐŽƵŶĚ volume control
ŽƉĞƌĂƟŽŶ is ƉƌŽŚŝďŝƚĞĚ for turn-up ĂŶĚ the ƐŽƵŶĚ volume ƐŚŽƵůĚ be ƚƵƌŶĞĚ ĚŽǁŶ to MAX in this state.
džƉůĂŶĂƟŽŶ The ƐŽƵŶĚ volume to be ĮdžĞĚ by "volume ĮdžĞĚ "is ĚĞƚĞƌŵŝŶĞĚ
Limit in ƐĞƫŶŐ
The ƐŽƵŶĚ volume for the ON-ƟŵĞƌ (wake up ƟŵĞƌͿ is ĮdžĞĚ also without ĚŝƐƉůĂLJ of ŵĞŶƵĞƐŝĚĞƐƚŚĞƐĞƫŶŐ is ŵĂĚĞ
impossible .(Basically ,the manu is not ĚŝƐƉůĂLJĞĚͿ
The ĨŽůůŽǁŝŶŐ keys become ŝŶǀĂůŝĚ
1) ^ŽƵŶĚ volume Up/Down(Vol +/- )( for both remote control ĂŶĚ the unit )
2)Mute ( MUTE )
In the item "VOLUME"af ĂĚũƵƐƚŵĞŶƚ process ,the ƐŽƵŶĚ volume can be set freely ŝƌƌĞƐƉĞĐƟǀĞ ot the ƐĞƫŶŐ
džĐĞƉƟŽŶ
Remark
^ĞůĞĐƟŽŶ
ĚũƵƐƚŵĞŶƚ from 1 to 100 (no loop )
Default
30
Limit in ƐĞƫŶŐ
None
džĐĞƉƟŽŶ
None
Remarks
^ĞƫŶŐ is ǀĂůŝĚ only when "Volume ĮdžĞĚ "is ƐĞůĞĐƚĞĚ for ΗĮdžĞĚΗ
This must be ĐŽŶĮƌŵĞĚ actually by ĐŚĂŶŐŝŶŐ also the ƐŽƵŶĚ volume in ĂĐĐŽƌĚĂŶĐĞ with ƐĞƫŶŐ
^ĞůĞĐƟŽŶ
^ĞůĞĐƟŽŶ between ΗZĞƐƉŽŶĚΗΗEŽ ƌĞƐƉŽŶĚ ΗĂŶĚ Η>ŝŵŝƚĞĚΗ (loop ƉƌŽǀŝĚĞͿ
ĚnopseRtluafeD
džƉůĂŶĂƟŽŶ
The ŽƉĞƌĂƟŽŶ of the remote control's Keys is set.
ZĞƐƉŽŶĚ :The remote control's Keys in the normal state are ĞŶĂďůĞĚ
No ƌĞƐƉŽŶĚ
:The remote control's Keys in the normal state are ĚŝƐĂďůĞĚ
The POWER Key ( RECEPTIONS /STANDBY Key ) is also ĚŝƐĂďůĞĚ
>ŝŵŝƚĞĚ :Only a part of Keys (CHANNEL,etc)is ĞŶĂďůĞĚĂŶĚ other keys are ĚŝƐĂďůĞĚ
Limit in ƐĞƫŶŐ 1) In ΗůŝŵŝƚĞĚΗ ƐĞƫŶŐŽŶůLJ power KEK&&ƐŽƵŶĚ volume ŸźƚƵŶŝŶŐ Ÿź ĂŶĚ BACKLIGHT ;ďƌŝŐŚƚŶĞƐƐ sensor )are
ĂĐĐĞƉƚĞĚ .
2) In "No ƌĞƐƉŽŶĚΗƐĞƫŶŐĂůů the keys ;ŝŶĐůƵĚŝŶŐ the power key )are not ĂĐĐĞƉƚĞĚ
ĚũƵƐƚŵĞŶƚ process,factory ƐĞƫŶŐŝŶƐƉĞĐƟŽŶ process ĂŶĚ hotel only keys are ǀĂůŝĚ ŝƌƌĞƐƉĞĐƟǀĞ of ƐĞƫŶŐ
All the keys can be ƵƐĞĚ in ĂĚũƵƐƚŵĞŶƚ ƉƌŽĐĞƐƐŝŶƐƉĞĐƟŽŶ ŵŽĚĞ ĂŶĚ hotel menu ŝƌƌĞƐƉĞĐƟǀĞ of ƐĞƫŶŐ
džĐĞƉƟŽŶ
Remarks
Page 29
LC-32LE265T / LC-40LE265T
3 – 22
7.PANEL BUTTON
^ĞůĞĐƟŽŶďĞƚǁĞĞŶΗZĞƐƉŽŶĚΗĂŶĚΗEŽƌĞƐƉŽŶĚΗ;ůŽŽƉƉƌŽǀŝĚĞͿ
Res
p
ŽŶĚ
^ĞůĞĐƟŽŶ
ĞĨĂƵůƚ
8.MENU BUTTON
"
"
"
"
>ŝŵŝƚ ŝŶ ƐĞƫŶŐ
džĐĞƉƟŽŶ
/ŶƐƉĞĐƟŽŶŵŽĚĞĂŶĚŚŽƚĞůŵĞŶƵŵŽĚĞĐĂŶ be ƐƚĂƌƚĞĚŝƌƌĞƐƉĞĐƟǀĞŽĨƐĞƫŶŐ
All the keys ĐĂŶ be ƵƐĞĚ ŝŶ ĂĚũƵƐƚŵĞŶƚ ƉƌŽĐĞƐƐŝŶƐƉĞĐƟŽŶ ŵŽĚĞ ĂŶĚ ŚŽƚĞů ŵĞŶƵ ŝƌƌĞƐƉĞĐƟǀĞ ŽĨ ƐĞƫŶŐ
ZĞŵĂƌŬƐ
EŽ ZĞƐƉŽŶĚ :The ŵĂŝŶ ƵŶŝƚΖƐ ŬĞLJƵƐ ĂƌĞ ĚŝƐĂďůĞĚ ĞdžĐůƵĚŝŶŐ the POWER ŬĞLJ;ZWd/KE^dEz key Ϳ
ZĞƐƉŽŶĚ
ZĞƐƉŽŶĚ :The ŵĂŝŶƵŶŝƚΖƐŬĞLJƐĂƌĞĞŶĂďůĞĚ
ĞĨĂƵůƚ
džƉůĂŶĂƟŽŶ
>ŝŵŝƚ ŝŶ ƐĞƫŶŐ
ON-ƟŵĞƌ;ǁĂŬĞƵƉdŝŵĞƌͿŝƐƚƵƌŶĞĚ OFF.
tĂŬĞ-ƵƉƟŵĞƌĂŶĚĐůŽĐŬƐĞƫŶŐ keys ĂŶĚĂůůŽĨ the ĚŝƌĞĐƚĐŚĂŶŐĞ keys ƚŽŵĞŶƵĚŝƐƉůĂLJ
The ĨŽůůŽǁŝŶŐ keys ďĞĐŽŵĞŝŶǀĂůŝĚ
ZĞƐƉŽŶĚ :The ŵĞŶƵ key ŝƐ ĚŝƐĂďůĞĚ
: /Ŷ " EŽ ƌĞƐƉŽŶĚΗ ƐĞƫŶŐƚŚĞ ŵĞŶƵ ŽƉĞƌĂƟŽŶ by the ŵĞŶƵ key ŽĨ the ƌĞŵŽƚĞĐŽŶƚƌŽůĂŶĚ
the ŵĞŶƵ key ŽĨ the ƵŶŝƚ ŝŶǀĂůŝĚĂƚĞĚ
/ŶƐƉĞĐƟŽŶŵŽĚĞĂŶĚŚŽƚĞůŵŽĚĞĐĂŶ be ƐƚĂƌƚĞĚŝƌƌĞƐƉĞĐƟǀĞŽĨƐĞƫŶŐ
All the keys ĐĂŶ be ƵƐĞĚ ŝŶ ĂĚũƵƐƚŵĞŶƚ ƉƌŽĐĞƐƐŝŶƐƉĞĐƟŽŶ ŵŽĚĞ ĂŶĚ ŚŽƚĞů ŵĞŶƵ ŝƌƌĞƐƉĞĐƟǀĞ ŽĨ ƐĞƫŶŐ
>ŝŵŝƚ ŝŶ ƐĞƫŶŐ
džĐĞƉƟŽŶ
ZĞŵĂƌŬƐ
tŚĞŶƌĞĐĞŝǀĞŝŶŐ the ƐŽƵŶĚ select ĚŝƌĞĐƚ key ;s POSITION ŬĞLJKW&ZŬĞLJĞƚĐͿŽŶůLJ the ƐĞůĞĐƚĞĚƐƚĂƚĞŝƐĚŝƐƉůĂLJĞĚŶŽƐĞƫŶŐŝƐĐŚĂŶŐĞĚ
The ƐĞƫŶŐĨŽƌ the WƵďůŝĐŵŽĚĞĂƌĞƌĞƚĂŝŶĞĚĂŌĞƌ the ƉĞƌƐŽŶĂůĚĂƚĂŝƐŝŶŝƟĂůŝnjĞĚĞĂĐŚŝƚĞŵĨŽƌ the AV ƉŽƐŝƟŽŶ
&ŝdžĞĚ :AV ƉŽƐŝƟŽŶ ŝƐ ĮdžĞĚ
:The ŝŵĂŐĞƐŽƵŶĚ ĂĚũƵƐƚŵĞŶƚ ŝƚĞŵƐ ŝŶ the ŵĞŶƵ ĂƌĞ ĮdžĞĚŝŶ the ƐĞůĞĐƚĞĚ ƐƚĂƚĞtŚĞŶƌĞĐĞŝǀŝŶŐ "AV POSITION ΗŽĨ the ƌĞŵŽƚĞĐŽŶƚƌŽůŽŶůLJ the ĂĐƚƵĂůĂƚĂƚĞŝƐĚŝƐƉůĂLJĞĚĂŶĚƐĞƫŶŐŝƐŶŽƚĐŚĂŶŐĞĚ
^ŝŵƉůĞ ŝŶƉƵƚƐǁŝƚĐŚŝŶŐŝƐŐĞŶĞƌĂƚĞĚdŚŽƐĞǁŚŝĐŚĂƌĞƌĞƐƚŽƌĞĚƐŽŽŶĂŌĞƌůĞĂǀŝŶŐĂƐ they ĂƌĞĂŶĚŵĂLJ be
>ŝŵŝƚ ŝŶ ƐĞƫŶŐ
Set ƟŵĞ ŽĨ the OFF-ƟŵĞƌ ;^>W d/DZͿŝƐ ĐůĞĂƌĞĚ
.
^ĞƫŶŐ ŽĨ the ŶŽ-ƐŝŐŶĂů ƉŽǁĞƌ-OFF ;hdK POWER OFF ͿŝƐ ĐůĞĂƌĞĚ ƚŽ "OFF".
^ĞƫŶŐ ŽĨ the ŶŽ-ŽƉĞƌĂƟŽŶ ƉŽǁĞƌ-OFF ŝƐ ĐůĞĂƌĞĚ ƚŽΗK&&Η
Keys ĨĂůůŝŶŐ ƵŶĚĞƌ ĂŶLJ ŽĨ the ĨŽůůŽǁŝŶŐ ŝƚĞŵƐ ďĞĐŽŵĞ ŝŶǀĂůŝĚ
ϭͿƉƉĞĂƌĂŶĐĞŽĨƐĐƌĞĞŶĐŚĂŶŐĞƐĂŶĚ the ƐŽƵŶĚĐŚĂŶŐĞƐϮͿWĞƌƐŽŶĂůĨƵŶĐƟŽŶƐǁŚŝĐŚĂƌĞŚĂƌĚƚŽƌĞƐƚŽƌĞdžͿ^ĐƌĞĞŶĚŝƐƉůĂLJŵĞŶƵK&&-ƟŵĞƌKE-ƟŵĞƌsDKƐĐƌĞĞŶƐŝnjĞƐǁŝƚĐŚŝŶŐĐůŽĐŬƐĞƫŶŐƚƌĞďůĞĞŵƉŚĂƐŝƐ
ƌĞƋƵĞƐƚĞĚĨŽƌĐŚĂŶŐĞ by ĐƵƐƚŽŵĞƌĂƌĞŶŽƚƉƌŽŚŝďŝƚĞĚdžͿƌŝŐŶĞƐƐƐĞŶƐŽƌ;<>/',dͿĂŶĚW/&>/W
^ƵĐŚ ĂĐĂƵƟŽŶǁŚŝĐŚŝƐĚŝƐƉůĂLJĞĚĂŶĚĞƉĞŶĚĞŶƚůLJŝƐĚŝƐƉůĂLJĞĚĂƐŝƚŝƐ .EŽŶ-ƌĞƐƉŽŶĚŝŶŐƐŝŐŶĂůĐĂƵƟŽŶd> TEXT ĐĂƵƟŽŶĂŶĚƉŽǁĞƌ-ON ĮdžŝŶŐĐĂƵƟŽŶ
/Ŷ ƉŽǁĞƌ-ON,the ŝŶƉƵƚ ƐŽƵƌĐĞ ƚŽ be ƐƚĂƌƚĞĚ Žƌ ĐŚĂŶŶĞů ĐĂŶ be set .
;/Ŷ ƐƚĂŶĚĂƌĚ ŵŽĚĞ ,the ŽƉĞƌĂƟŽŶ ĨŽůůŽǁƐ the ůĂƐƚ ŵĞŵŽƌLJͿ
ďŽƵƚ ŽƉƟŽŶ
ƐǁŝƚĐŚŝŶŐŬĞLJ
•
All the ŝŶƉƵƚƐŽƵƌĐĞŝŶ the ŵŽĚĞůĂƌĞŵĂĚĞƐĞůĞĐƚĂďůĞ
•
tŚĞŶ the ŝŶƉƵƚŽƵƚƉƵƚƐǁŝƚĐŚĂďůĞŝŶƉƵƚƐŽƵƌĐĞ is ƐĞůĞĐƚĞĚĂŶĚ the ŝŶƉƵƚƐŽƵƌĐĞ is set ƚŽŽƵƚƉƵƚƚŚĞƐĞƫŶŐŽĨŝŶƉƵƚŽƵƚƉƵƚƐǁŝƚĐŚŝŶŐ is ĐŚĂŶŐĞĚƚŽŝŶƉƵƚĂƚ the ĞdžĞĐƵƟŽŶŽĨŚŽƚĞůŵĞŶƵ/ŶĂĚĚŝƟŽŶƚŚĞŝŶƉƵƚŽƵƚƉƵƚƐǁŝƚĐŚŝŶŐďLJŵĞŶƵ is ƉƌŽŚŝďŝƚĞĚ
•
/Ŷ TV ŵŽĚĞƚŚĞĚŝƐƉůĂLJŽĨĂůůĐŚĂŶŶĞůƐ is ƐƚŽƉƉĞĚĂŶĚ it is ƚƌĞĂƚĞĚĂƐĂŶŝŶƉƵƚƐŽƵƌĐĞ .At this ƟŵĞƚŚĞ
the ĐŚĂŶŶĞůƚŽ be set ĨŽůůŽǁƐ the ůĂƐƚŵĞŵŽƌLJĂŶĚ the ĐŽŶƚĞŶƚŽĨ the ůĂƐƚŵĞŵŽƌLJ is ŝŶĐůƵĚĞĚŝŶ the
ŶŽƚĂƟŽŶďLJŽƉƟŽŶƐdžͿds;,ϮͿ TV ;,ϰͿ etc.
•
The ŽƌĚĞƌŽĨĂƉƉĞĂƌĂŶĐĞŽĨŽƉƟŽŶŝŶ the ŚŽƚĞůŵĞŶƵƐŚŽƵůĚĂŐƌĞĞ with ŽƌĚĞƌƚŽŐŐůĞƐďLJŝŶƉƵƚ
12.INPUT MODE FIXED
ĞĨĂƵůƚ
-;sĂƌŝĂďůĞͿ
ƐǁŝƚĐŚŝŶŐŬĞLJ
>ŝŵŝƚ ŝŶ ƐĞƫŶŐ
• The ĚŝƐƉůĂLJ ŽĨ ĐŚĂŶŶĞů ƐĞƫŶŐ ŵĞŶƵ ĂŶĚ the ĐŚĂŶŶĞů ƐĞƫŶŐ ŽƉĞƌĂƟŽŶ ĂƌĞ ƉƌŽŚŝďŝƚĞĚ ;ĞdžĐĞƉƚ ĨŽƌ MCL Ϳ
džĐĞƉƟŽŶ
EŽŶĞ
•
/ŶƐĞƫŶŐĂƚΗEŽƌŵĂůΗƚŚĞƐĞƫŶŐŽĨΗ/ŶƉƵƚŵŽĚĞĮdžĞĚ "is ĐŚĂŶŐĞĚƚŽΗsĂƌŝĂďůĞΗĂŶĚƐĞůĞĐƟŽŶƐŚŽƵůĚ
be ƉƌŽŚŝďŝƚĞĚ
tŚĞŶ TV ƉŽǁĞƌ ON ĨƌŽŵĚĞĞƉƐƚĂŶĚďLJƉŽǁĞƌŽīŽƌ AC ŽīŵŽĚĞ ,TV ŶĞĞĚƐƚŽĚŝƐƉůĂLJWh>/ƉŝĐƚƵƌĞĨŽƌƐĞƫŶŐƟŵĞ
•
tŚĞŶ TV ƉŽǁĞƌ ON ĨƌŽŵƐƚĂŶĚďLJŵŽĚĞ ,TV ŶĞĞĚŶΖƚƚŽĚŝƐƉůĂLJWh>/ƉŝĐƚƵƌĞ .
•
tŚĞŶĚŝƐƉůĂLJŝŶŐWh>/ƉŝĐƚƵƌĞĂŬĞLJŝŶƉƵƚ
Page 31
LC-32LE265T / LC-40LE265T
3 – 24
16.RC PATH THROUGH
17.PUBLIC MODE
The from decide whether the signal received by the remote control's light -receiving ƐĞĐƟŽŶ is output to
the blankpin (9pin) of RS232C
Fixed : This ĨƵŶĐƟŽŶ is not ĂĐƟǀĞ
On: TV RCE : This ĨƵŶĐƟŽŶ is ĂĐƟǀĞĂŶĚ remote is ĂĐƟǀĞƚŽŽ
On: TV RCD : This ĨƵŶĐƟŽŶ is ĂĐƟǀĞĂŶĚ remote is not ĂĐƟǀĞ
Remarks
Each ŽƉĞƌĂƟŽŶ of the Public mode is impossible unless this item is set to ON
^ĞůĞĐƟŽŶ
ffOtluafeD
džƉůĂŶĂƟŽŶ
The item decide whether Public mode ƐĞƫŶŐ manu are enabled or disabled.
The same item as [ PUBLIC MODE ] in the adjustment process menu.
OFF : Public mode is not ĂĐƟǀĞ .
On: : Public mode not ĂĐƟǀĞ
Η&ŝdžĞĚΗΗKŶds ZΗΗKŶds RCD (loop enabled )
ΗKī and On"(loop enabled)
džĐĞƉƟŽŶ None
Limit in ƐĞƫŶgNone
Limit in ƐĞƫŶgWhen set to "On :TV ZΗds does not accept the remote control.
džĐĞƉƟŽŶ None
Remarks
^ĞůĞĐƟŽŶ
ffOtluafeD
džƉůĂŶĂƟŽŶ
Page 32
LC-32LE265T / LC-40LE265T
4 – 1
CHAPTER 4. TROUBLESHOOTING
TABLE
[1] TROUBLESHOOTING TABLE
[1] TROUBLESHOOTING TABLE
No power (front LED failure to light up) or no startup (front LED failure to turn from red to green)
Are the wire harnesses and other cables properly connected in
the set?
NOReconnect the wire harnesses and other cables properly in the
set.
YES
Is there the PS_ON and PNL_POW signal input at pins
(10 ) and (12
) of P9602?
NOCheck the
PS_ON signal line PNL _POW signal line.
YES
Are the DC/DC converter outputs and the output voltages along
the control lines as specified?
NOCheck the DC/DC converters and the control lines. Replace
defective parts as required.
1) M+5.6V (IC9601) 8) BU+3.3V (IC9604)
2) D+1.2V
(IC9602)
3) D+5V (IC9607)
4) BU+5V (D9610)
5) D+3.3V (IC9606)
6)
D+1.5V (IC9608)
7) D+1.2V
(IC9602)
9) D+2.5V (IC9605)
10) PNL +13V (AO6405 )
Page 33
LC-32LE265T / LC-40LE265T
4 – 2
With [RF] signal inputNo video onscreen (1)
No video in the UHF/VHF reception
Is there IF output from the tuner pin(8)(9
) of
TU1102 as specified? NOCheck TU1102 and its peripheral circuits.
YES
.1033CI&2011UTneewtebtiucricehtkcehCON
YES
NO
YES
Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits.
With <Video> signal input No video onscreen (2)
Is INPUTelected on the input select menu screen?NO
YES
Is there the video signal input at pin (R2) of IC3301?NOCheck the line between pin (9) of J502 and pin (R2) of IC3301.
YES
NOCheck IC3301 and its peripheral circuits
to SC3801
YES
Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits.
Are ther the signal outputs pin ( P19-P20 , R19-R21 ,T19T21,U19-U20,V19-V21,WE18-W21,Y18-Y21,AA18-AA20 ) ?
Are there the signal outputs (pin of IC3301 to SC 3801) ?
( P19-P20,R19-R21,T19,U19-U20,V19-V21,WE18-W21,Y18Y21,AA18-AA20 )
Is there IF input at pin W1 & W2 of IC3301 ?
Check IC3301 and its peripheral circuit to SC3801
No external input video onscreen < INPUT 7 >
7s
Select INPUT 5 on the input select menu screen to pick
up the right input signal.
Page 34
LC-32LE265T / LC-40LE265T
4 – 3
With <Component> signal input No video onscreen (3)
No external input video onscreen <INPUT
NO
YES
Are there the Y, Pb and Pr signal inputs at pins (L1), (L3) and
(M1
) of IC 3301 respectively?
NOCheck the line between pins (15)/(17)/(19 )of J502 and pins (L1)/
(L3) /(M1) of IC3301.
YES
NOCheck IC3301 and its peripheral circuits.
YES
Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits.
No video onscreen (4)
NO
YES
Are there signal outputs from SC1501/SC1503 / SC1504 /
NO
YES
Are there the signal outputsNOCheck IC3301 and its peripheral circuits.
YES
Check LVDS cable, LCD controller (incl. panel) and their peripheral circuits.
Are there the signal outputs
(P19-P20 ,R19-R21,T19-T21,U19-U20,
V19-V21,W18-W21,Y18-Y21,AA18-AA20 ) of IC3301?
SC1506 /SC1507 to IC3301 ?
P19-P20,R19-R21,T19-T21,U19-U20
,V19-V21,W18-W21,Y18-Y21 ,AA18-AA20 of IC3301 ?
4>
Is INPUT 6 selected on the input select
menu screen ?
Select INPUT 6 on the input select menu screen to pick
up the right input signal .
With <HDMI1/HDMI2/HDMI3/HDMI4/HDMI5> signal input
No external input video onscreen INPUT1/INPUT2/INPUT3
Is <INPUT1/INPUT2/INPUT3/INPUT4/INPUT5
selected on the menu screen ?
Select <INPUT1/INPUT2/INPUT3/INPUT4/INPUT5>
select menu screen to pick up the right signal
input
Select <INPUT1/INPUT2/INPUT3/INPUT4/INPUT5
select menu screen to pick up the right signal
input
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of
P1702 n
ormal?
NOCheck circuit between IC1702 & P1701.
YES
Check speakers and their peripheral circuits.
(30),(31)
of IC1702 normal?
Is the R-ch audio signal output at pin (10
(11), (14)(15),
Is the IF output from the tuner pin(8) & (9)
ofTU1102 as specified ?
Page 36
LC-32LE265T / LC-40LE265T
4 – 5
No audio heard (2)
No external audio heard
Is there the L-ch audio signal input from pin (7) of input terminal
J502 to pin (U4) of IC3301?
Is there the R-ch audio signal input from pin (5) of input terminal
J502 to pin (
U5
) of I
C3301?
Is there the L-ch audio signal input from pin (13) of input terminal
J502 to pin (
T6) of I
C3301?
Is there
the R-ch au
dio signal input from pin (11) of input terminal
J502 to pin (
T7
) of I
C3301?
YES
Is there the I2S signal output at pin ( J19),(J20) of IC3301 ?NOCheck IC3301 and its peripheral circuits.
YES
ON?2071CIfo)6(niptatupnilangisoiduaerehtsICheck connection between IC3301 and IC1702 and its periph-
eral circuits.
YES
Is the L-ch audio signal output at pin(26), (27) ,(30),(31) of
IC1702 normal ?
NOCheck IC1702 and its peripheral circuits.
Is the R-ch audio signal output at pin(10), (11),(14),(15) of
IC1702 normal ?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of
P1701 normal?
NOCheck circuit between IC1702 & P1701.
YES
Check speakers and their peripheral circuits.
< INPUT 5 >
< INPUT 4 >
Page 37
LC-32LE265T / LC-40LE265T
4 – 6
No audio heard (3)
ON?neercsnoraeppaegamiIMDHehtseoD
YES
.tonronettirwsiDIDEfitikcehCONmorftuptuooiduaoN
YES
NOCheck peripheral circuits
YES
ONfo)6(niptatupnilangisoiduaerehtsI
YES
Is the L-ch audio signal output at pin(26), (27) ,(30), (31) NOCheck IC1702 and its peripheral circuits.
of IC
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of
P1701 n
ormal?
NOCheck circuit between IC1702 & P1701.
YES
Check speakers and their peripheral circuits.
of IC
1702 no
rmal?
Is the R-ch audio signal output at pin(10),(11),(14),(15)
No HDMI sound heard <INPUT1 /INPUT2 /INPUT3 >
(*INPUT1/INPUT2/INPUT3 is digital audio )
Refer to “ ( Input1/Input2 / Input3 )is no external
input video screen (HDMI)”
<INPUT1/INPUT2/INPUT3>
Are waveforms output from each HDMI pin
normaly?
IC1702 ?
for each HDMI socket.
Check connection between IC3301 and IC1702
and its peripheral circuit.
1702 normal ?
Page 38
LC-32LE265T / LC-40LE265T
4 – 7
No audio heard (4)
No sound from the HDMI sound input terminal.
(INPUT 1 analog audio)
YES
Is there the L-ch audio signal input from pin (2) of external input
terminal J506 (HDMI AUDIO IN) to pin (U3
) of IC3301?
Is there the R-ch audio signal input from pin (3) of external input
terminal J506 (HDMI AUDIO IN)
to pin (U1) of IC3301?
YES
NOCheck peripheral circuits of IC3301.
YES
CON?2071CIfo)6(niptatupnilangisoiduaerehtsIheck connection between IC3301 and IC1702 and its peripheral circuits.
YES
Is the L-ch audio signal output at pin(26),(27),(30),(31)
NOCheck IC1702 and its peripheral circuits.
of IC
1702 normal?
YES
Are the audio signal L-ch and R-ch output at (3)/(4) and (1)/(2) of
P1701 normal?
NOCheck circuit between IC1702 & P1701.
YES
Check speakers and their peripheral circuits.
of IC1702 normal?
Is the R
-ch audio signal output at pin(10),(11),(14),(15)
Are 12S signal output from the pins ( J19 )
,(J20 ) of IC3301 normally
Parts marked with "" are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Page 67
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[1] PRINTED WIRING BOARD ASSEMBLIES
1 DKEYMG567FM02VMain Unit ( LC-32LE265T )
1 DKEYMG567FM01VMain Unit ( LC-40LE265T )
1 DUNTKG409FM02VPower Unit ( LC-32LE265T )
1 RDENCA474WJPZBTVPower Unit ( LC-40LE265T )
1 DUNTKG463FM01AZVLed / IR Unit
[2] LCD PANEL
1 R1LK315T3HB60WVLCD HIRAKI PANEL UNIT ( LC-32LE265T )
1 CLCDTA377WE08VLCD PANEL MODULE UNIT ( LC-32LE265T )
1 CLCDTA373WE09VLCD PANEL MODULE UNIT ( LC-40LE265T )
1 RLCDTA325WJQZCMVLCD HIRAKI PANEL UNIT ( LC-40LE265T )
1 RUNTKB281WJZZBDVLED BAR (A)
1 RUNTKB282WJZZBDVLED BAR (B)
[3] DKEYMG567FM02 / 01 (MAIN Unit)
SC 3801 QCNCWB019WJQZYVLVDS Connector
J 0504 QJAKJA054WJQZYVHeadphone Jack
P 1701 QPLGNB092WJZZYVSP Connector
P 3301 QPLGNB150WJZZYVRA Connector
L 3801 RCIL FA421WJZZYVCoil
L 3802 RCIL FA421WJZZYVCoil ( Only for LC-40LE265T )
L 3803 RCIL FA421WJZZYVCoil ( Only for LC-40LE265T )
L 3804 RCIL FA421WJZZYVCoil
L 3805 RCIL FA421WJZZYVCoil
L 3806 RCIL FA421WJZZYVCoil ( Only for LC-40LE265T )
L 0501 RCIL FA424WJZZYVCoil
L 9604 RCIL PB011WJQZYVCoil
L 9601 RCIL PB014WJQZYVCoil
L 9602 RCIL PB014WJQZYVCoil
L 9603 RCIL PB014WJQZYVCoil
L 1701 RCIL PB489WJQZYVCoil
L 1702 RCIL PB489WJQZYVCoil
L 1703 RCIL PB489WJQZYVCoil
L 1704 RCIL PB489WJQZYVCoil
X 3301 RCRS CA315WJZZYVCrystal
FL 3508 RFILNA119WJZZYVCoil
D 0519 RH-EXA741WJQZYVDiode
TH 3301 RH-HXA047WJQZYVThermistor
IC 3502 RH-IXD406WJQZQVIC
IC 3301 RH-IXD599WJQZQVIC
C 0502 VCCCCZ1HH100DYVChip Capacitor
C 0504 VCCCCZ1HH100DYVChip Capacitor
C 1125 VCCCCZ1HH100DYVChip Capacitor
DESCRIPTION
3
Page 69
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
C 1128 VCCCCZ1HH100DYVChip Capacitor
C 3349 VCCCCZ1HH100DYVChip Capacitor
C 3350 VCCCCZ1HH100DYVChip Capacitor
C 3367 VCCCCZ1HH101JYVChip Capacitor
C 3368 VCCCCZ1HH101JYVChip Capacitor
C 3369 VCCCCZ1HH101JYVChip Capacitor
C 9622 VCCCCZ1HH150JYVChip Capacitor
C 0560 VCCCCZ1HH470JYVChip Capacitor
C 0561 VCCCCZ1HH470JYVChip Capacitor
C 1115 VCCCCZ1HH470JYVChip Capacitor
C 1116 VCCCCZ1HH470JYVChip Capacitor
C 0514 VCCCCZ1HH560JYVChip Capacitor
C 0517 VCCCCZ1HH560JYVChip Capacitor
C 0530 VCCCCZ1HH560JYVChip Capacitor
C 0532 VCCCCZ1HH560JYVChip Capacitor
C 0543 VCCCCZ1HH560JYVChip Capacitor
C 0544 VCCCCZ1HH560JYVChip Capacitor
C 1755 VCCCCZ1HH821JYVChip Capacitor
C 1756 VCCCCZ1HH821JYVChip Capacitor
C 1753 VCKYCY1AB224KYVChip Capacitor
C 1754 VCKYCY1AB224KYVChip Capacitor
C 1757 VCKYCY1AB224KYVChip Capacitor
C 1758 VCKYCY1AB224KYVChip Capacitor
C 1719 VCKYCY1EB104KYVChip Capacitor
C 1720 VCKYCY1EB104KYVChip Capacitor
C 1726 VCKYCY1EB104KYVChip Capacitor
C 1727 VCKYCY1EB104KYVChip Capacitor
C 1746 VCKYCY1HB102KYVChip Capacitor
C 1747 VCKYCY1HB102KYVChip Capacitor
C 0524 VCKYCZ1AB104KYVChip Capacitor
C 0540 VCKYCZ1AB104KYVChip Capacitor
C 3104 VCKYCZ1AB104KYVChip Capacitor
C 3307 VCKYCZ1AB104KYVChip Capacitor
C 3309 VCKYCZ1AB104KYVChip Capacitor
C 3310 VCKYCZ1AB104KYVChip Capacitor
C 3311 VCKYCZ1AB104KYVChip Capacitor
C 3313 VCKYCZ1AB104KYVChip Capacitor
C 3316 VCKYCZ1AB104KYVChip Capacitor
C 3320 VCKYCZ1AB104KYVChip Capacitor
C 3321 VCKYCZ1AB104KYVChip Capacitor
C 3323 VCKYCZ1AB104KYVChip Capacitor
C 3324 VCKYCZ1AB104KYVChip Capacitor
C 3325 VCKYCZ1AB104KYVChip Capacitor
C 3328 VCKYCZ1AB104KYVChip Capacitor
C 3331 VCKYCZ1AB104KYVChip Capacitor
C 3335 VCKYCZ1AB104KYVChip Capacitor
C 3336 VCKYCZ1AB104KYVChip Capacitor
C 3337 VCKYCZ1AB104KYVChip Capacitor
C 3338 VCKYCZ1AB104KYVChip Capacitor
C 3339 VCKYCZ1AB104KYVChip Capacitor
C 3340 VCKYCZ1AB104KYVChip Capacitor
C 3341 VCKYCZ1AB104KYVChip Capacitor
C 3342 VCKYCZ1AB104KYVChip Capacitor
C 3344 VCKYCZ1AB104KYVChip Capacitor
C 3345 VCKYCZ1AB104KYVChip Capacitor
C 3351 VCKYCZ1AB104KYVChip Capacitor
C 3365 VCKYCZ1AB104KYVChip Capacitor
C 3502 VCKYCZ1AB104KYVChip Capacitor
C 3504 VCKYCZ1AB104KYVChip Capacitor
C 3505 VCKYCZ1AB104KYVChip Capacitor
C 3506 VCKYCZ1AB104KYVChip Capacitor
C 3507 VCKYCZ1AB104KYVChip Capacitor
C 3509 VCKYCZ1AB104KYVChip Capacitor
C 3510 VCKYCZ1AB104KYVChip Capacitor
C 3511 VCKYCZ1AB104KYVChip Capacitor
C 3512 VCKYCZ1AB104KYVChip Capacitor
C 3513 VCKYCZ1AB104KYVChip Capacitor
C 3514 VCKYCZ1AB104KYVChip Capacitor
C 3515 VCKYCZ1AB104KYVChip Capacitor
C 3516 VCKYCZ1AB104KYVChip Capacitor
C 3517 VCKYCZ1AB104KYVChip Capacitor
C 3518 VCKYCZ1AB104KYVChip Capacitor
C 3519 VCKYCZ1AB104KYVChip Capacitor
C 3520 VCKYCZ1AB104KYVChip Capacitor
C 9669 VCKYCZ1AB104KYVChip Capacitor
C 9671 VCKYCZ1AB104KYVChip Capacitor
C 3405 VCKYCZ1AB473KYVChip Capacitor
C 3407 VCKYCZ1AB473KYVChip Capacitor
C 3408 VCKYCZ1AB473KYVChip Capacitor
C 3409 VCKYCZ1AB473KYVChip Capacitor
C 3305 VCKYCZ1CB223KYVChip Capacitor
C 1501 VCKYCZ1CB473KYVChip Capacitor
C 3312 VCKYCZ1CB473KYVChip Capacitor
C 3315 VCKYCZ1CB473KYVChip Capacitor
C 3399 VCKYCZ1CB473KYVChip Capacitor
DESCRIPTION
4
Page 70
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
C 3401 VCKYCZ1CB473KYVChip Capacitor
C 3402 VCKYCZ1CB473KYVChip Capacitor
C 3403 VCKYCZ1CB473KYVChip Capacitor
C 3404 VCKYCZ1CB473KYVChip Capacitor
C 0508 VCKYCZ1EB103KYVChip Capacitor
C 0509 VCKYCZ1EB103KYVChip Capacitor
C 3343 VCKYCZ1EB103KYVChip Capacitor
C 3503 VCKYCZ1EB103KYVChip Capacitor
C 0584 VCKYCZ1EB104KYVChip Capacitor
C 0585 VCKYCZ1EB104KYVChip Capacitor
C 0586 VCKYCZ1EB104KYVChip Capacitor
C 0587 VCKYCZ1EB104KYVChip Capacitor
C 0589 VCKYCZ1EB104KYVChip Capacitor
C 1113 VCKYCZ1EB104KYVChip Capacitor
C 1117 VCKYCZ1EB104KYVChip Capacitor
C 1118 VCKYCZ1EB104KYVChip Capacitor
C 1120 VCKYCZ1EB104KYVChip Capacitor
C 1147 VCKYCZ1EB104KYVChip Capacitor
C 1148 VCKYCZ1EB104KYVChip Capacitor
C 1103 VCKYCZ1EF104ZYVChip Capacitor
C 1721 VCKYCZ1EF104ZYVChip Capacitor
C 1752 VCKYCZ1EF104ZYVChip Capacitor
C 0526 VCKYCZ1HB102KYVChip Capacitor
C 0527 VCKYCZ1HB102KYVChip Capacitor
C 0548 VCKYCZ1HB102KYVChip Capacitor
C 0553 VCKYCZ1HB102KYVChip Capacitor
C 0588 VCKYCZ1HB102KYVChip Capacitor
C 1101 VCKYCZ1HB102KYVChip Capacitor
C 1734 VCKYCZ1HB102KYVChip Capacitor
C 1759 VCKYCZ1HB102KYVChip Capacitor
C 1760 VCKYCZ1HB102KYVChip Capacitor
C 1774 VCKYCZ1HB102KYVChip Capacitor
C 1775 VCKYCZ1HB102KYVChip Capacitor
C 3301 VCKYCZ1HB102KYVChip Capacitor
C 3302 VCKYCZ1HB102KYVChip Capacitor
C 3334 VCKYCZ1HB102KYVChip Capacitor
C 3393 VCKYCZ1HB102KYVChip Capacitor
C 3400 VCKYCZ1HB102KYVChip Capacitor
C 3406 VCKYCZ1HB102KYVChip Capacitor
C 3501 VCKYCZ1HB102KYVChip Capacitor
C 3508 VCKYCZ1HB102KYVChip Capacitor
C 9608 VCKYCZ1HB102KYVChip Capacitor
C 9609 VCKYCZ1HB102KYVChip Capacitor
C 9611 VCKYCZ1HB102KYVChip Capacitor
C 9656 VCKYCZ1HB102KYVChip Capacitor
C 9662 VCKYCZ1HB102KYVChip Capacitor
D 9610 VHDRB160M40-1YVDiode
D 1502 VHDRB521M30-1YVDiode
D 1503 VHDRB521M30-1YVDiode
D 1504 VHDRB521M30-1YVDiode
D 1511 VHDRB521M30-1YVDiode
D 1512 VHDRB521M30-1YVDiode
D 1513 VHDRB521M30-1YVDiode
D 3301 VHDRB521M30-1YVDiode
IC 9608 VHI13A1C15U-1YVIC
IC 9605 VHI13A1C25U-1YVIC
IC 9604 VHI13A1C33U-1YVIC
IC 0512 VHIAHT1G08W-1YVIC
IC 1501 VHIAHT1G08W-1YVIC
IC 0513 VHIBD2242G+-1YVIC
IC 1703 VHIBU4229G+-1YVIC
IC 1705 VHIBU4229G+-1YVIC
IC 3304 VHIBU4229G+-1YVIC
IC 0511 VHIM3221EIP-1YVIC
IC 9601 VHIMP1495DJ-1YVIC
IC 9602 VHIMP1495DJ-1YVIC
IC 9606 VHIMP1495DJ-1YVIC
IC 9617 VHIMP1499GD-1YVIC
IC 1701 VHINJU72014-1YVIC
IC 1502 VHIPS2553DB-1YVIC
IC 9607 VHIS172B50U-1YVIC
IC 1704 VHITPA6139A-1YVIC
IC 3104 VHIW25Q28FV-1YVIC
IC 1702 VHIYDA176DL-1YVIC
L 1101 VPMT NR47JR65NYVCoil
L 1102 VPMT NR47JR65NYVCoil
R 3379 VRK-SA1JF100JYVChip Resistor
R 3380 VRK-SA1JF101JYVChip Resistor
R 3381 VRK-SA1JF101JYVChip Resistor
R 3372 VRK-SA1JF102JYVChip Resistor
R 3385 VRK-SA1JF182JYVChip Resistor
R 3371 VRK-SA1JF333JYVChip Resistor
R 1519 VRK-SA1JF473JYVChip Resistor
R 1520 VRK-SA1JF473JYVChip Resistor
R 1521 VRK-SA1JF473JYVChip Resistor
DESCRIPTION
5
Page 71
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
R 3508 VRK-SB1FF101JYVChip Resistor
R 3509 VRK-SB1FF101JYVChip Resistor
R 3510 VRK-SB1FF101JYVChip Resistor
R 3511 VRK-SB1FF101JYVChip Resistor
R 3512 VRK-SB1FF101JYVChip Resistor
R 3513 VRK-SB1FF101JYVChip Resistor
R 3514 VRK-SB1FF101JYVChip Resistor
R 3515 VRK-SB1FF101JYVChip Resistor
R 3516 VRK-SB1FF101JYVChip Resistor
R 3517 VRK-SB1FF101JYVChip Resistor
R 3518 VRK-SB1FF101JYVChip Resistor
R 3519 VRK-SB1FF101JYVChip Resistor
R 3520 VRK-SB1FF220JYVChip Resistor
R 3521 VRK-SB1FF220JYVChip Resistor
R 3522 VRK-SB1FF220JYVChip Resistor
R 3523 VRK-SB1FF220JYVChip Resistor
R 3524 VRK-SB1FF220JYVChip Resistor
R 3525 VRK-SB1FF220JYVChip Resistor
R 3526 VRK-SB1FF220JYVChip Resistor
R 3527 VRK-SB1FF220JYVChip Resistor
R 3528 VRK-SB1FF220JYVChip Resistor
R 3529 VRK-SB1FF220JYVChip Resistor
R 3532 VRK-SB1FF220JYVChip Resistor
R 0624 VRS-CY1JF000JYVChip Resistor
R 1108 VRS-CY1JF101JYVChip Resistor
R 1109 VRS-CY1JF101JYVChip Resistor
R 1524 VRS-CY1JF101JYVChip Resistor
R 1525 VRS-CY1JF101JYVChip Resistor
R 0553 VRS-CZ1JF000JYVChip Resistor
R 0554 VRS-CZ1JF000JYVChip Resistor
R 0615 VRS-CZ1JF000JYVChip Resistor
R 0616 VRS-CZ1JF000JYVChip Resistor
R 1104 VRS-CZ1JF000JYVChip Resistor
R 1107 VRS-CZ1JF000JYVChip Resistor
R 1120 VRS-CZ1JF000JYVChip Resistor
R 1121 VRS-CZ1JF000JYVChip Resistor
R 1509 VRS-CZ1JF000JYVChip Resistor
R 1515 VRS-CZ1JF000JYVChip Resistor
R 1748 VRS-CZ1JF000JYVChip Resistor
R 1754 VRS-CZ1JF000JYVChip Resistor
R 1769 VRS-CZ1JF000JYVChip Resistor
R 1796 VRS-CZ1JF000JYVChip Resistor
R 3302 VRS-CZ1JF000JYVChip Resistor
R 3303 VRS-CZ1JF000JYVChip Resistor
R 3330 VRS-CZ1JF000JYVChip Resistor
R 3332 VRS-CZ1JF000JYVChip Resistor
R 3444 VRS-CZ1JF000JYVChip Resistor
R 3450 VRS-CZ1JF000JYVChip Resistor
R 3806 VRS-CZ1JF000JYVChip Resistor
R 3807 VRS-CZ1JF000JYVChip Resistor
R 3808 VRS-CZ1JF000JYVChip Resistor
R 3809 VRS-CZ1JF000JYVChip Resistor
R 3886 VRS-CZ1JF000JYVChip Resistor
R 3887 VRS-CZ1JF000JYVChip Resistor
R 3888 VRS-CZ1JF000JYVChip Resistor
R 3889 VRS-CZ1JF000JYVChip Resistor
R 9603 VRS-CZ1JF102JYVChip Resistor ( Only for LC-40LE265T )
R 9604 VRS-CZ1JF000JYVChip Resistor
R 9606 VRS-CZ1JF000JYVChip Resistor
R 9635 VRS-CZ1JF000JYVChip Resistor
R 9671 VRS-CZ1JF000JYVChip Resistor
R 0556 VRS-CZ1JF101JYVChip Resistor
R 0613 VRS-CZ1JF101JYVChip Resistor
R 0614 VRS-CZ1JF101JYVChip Resistor
R 0620 VRS-CZ1JF101JYVChip Resistor
R 0621 VRS-CZ1JF101JYVChip Resistor
R 0622 VRS-CZ1JF101JYVChip Resistor
R 0623 VRS-CZ1JF101JYVChip Resistor
R 1105 VRS-CZ1JF101JYVChip Resistor
R 3363 VRS-CZ1JF101JYVChip Resistor
R 3365 VRS-CZ1JF101JYVChip Resistor
R 3366 VRS-CZ1JF101JYVChip Resistor
R 3367 VRS-CZ1JF101JYVChip Resistor
R 3424 VRS-CZ1JF101JYVChip Resistor
R 3429 VRS-CZ1JF101JYVChip Resistor
R 3430 VRS-CZ1JF101JYVChip Resistor
R 3432 VRS-CZ1JF101JYVChip Resistor
R 3433 VRS-CZ1JF101JYVChip Resistor
R 3460 VRS-CZ1JF101JYVChip Resistor
R 9605 VRS-CZ1JF101JYVChip Resistor
R 3501 VRS-CZ1JF102FYVChip Resistor
R 3502 VRS-CZ1JF102FYVChip Resistor
R 3504 VRS-CZ1JF102FYVChip Resistor
R 3505 VRS-CZ1JF102FYVChip Resistor
R 1502 VRS-CZ1JF102JYVChip Resistor
DESCRIPTION
6
Page 72
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
R 1504 VRS-CZ1JF102JYVChip Resistor
R 1523 VRS-CZ1JF102JYVChip Resistor
R 1701 VRS-CZ1JF102JYVChip Resistor
R 1702 VRS-CZ1JF102JYVChip Resistor
R 1750 VRS-CZ1JF102JYVChip Resistor
R 1751 VRS-CZ1JF102JYVChip Resistor
R 1767 VRS-CZ1JF102JYVChip Resistor
R 1768 VRS-CZ1JF102JYVChip Resistor
R 3326 VRS-CZ1JF102JYVChip Resistor
R 3327 VRS-CZ1JF102JYVChip Resistor
R 3328 VRS-CZ1JF102JYVChip Resistor
R 3373 VRS-CZ1JF102JYVChip Resistor
R 9645 VRS-CZ1JF102JYVChip Resistor
R 1792 VRS-CZ1JF103FYVChip Resistor
R 9617 VRS-CZ1JF103FYVChip Resistor
R 0513 VRS-CZ1JF103JYVChip Resistor
R 0516 VRS-CZ1JF103JYVChip Resistor
R 0534 VRS-CZ1JF103JYVChip Resistor
R 0536 VRS-CZ1JF103JYVChip Resistor
R 0570 VRS-CZ1JF103JYVChip Resistor
R 0577 VRS-CZ1JF103JYVChip Resistor
R 0578 VRS-CZ1JF103JYVChip Resistor
R 1102 VRS-CZ1JF103JYVChip Resistor
R 1549 VRS-CZ1JF103JYVChip Resistor
R 1550 VRS-CZ1JF103JYVChip Resistor
R 1551 VRS-CZ1JF103JYVChip Resistor
R 1797 VRS-CZ1JF103JYVChip Resistor
R 3311 VRS-CZ1JF103JYVChip Resistor
R 3312 VRS-CZ1JF103JYVChip Resistor
R 3337 VRS-CZ1JF103JYVChip Resistor
R 3390 VRS-CZ1JF103JYVChip Resistor
R 3431 VRS-CZ1JF103JYVChip Resistor
R 3449 VRS-CZ1JF103JYVChip Resistor
R 3801 VRS-CZ1JF103JYVChip Resistor
R 9607 VRS-CZ1JF103JYVChip Resistor
R 9611 VRS-CZ1JF103JYVChip Resistor
R 9619 VRS-CZ1JF103JYVChip Resistor
R 9621 VRS-CZ1JF103JYVChip Resistor
R 9646 VRS-CZ1JF103JYVChip Resistor
R 9653 VRS-CZ1JF103JYVChip Resistor
R 9661 VRS-CZ1JF103JYVChip Resistor
R 9630 VRS-CZ1JF104FYVChip Resistor
R 0506 VRS-CZ1JF104JYVChip Resistor
R 0510 VRS-CZ1JF104JYVChip Resistor
R 0525 VRS-CZ1JF104JYVChip Resistor
R 0527 VRS-CZ1JF104JYVChip Resistor
R 0104 VRS-CZ1JF123JYVChip Resistor
R 0511 VRS-CZ1JF123JYVChip Resistor
R 0515 VRS-CZ1JF123JYVChip Resistor
R 0532 VRS-CZ1JF123JYVChip Resistor
R 0535 VRS-CZ1JF123JYVChip Resistor
R 0581 VRS-CZ1JF123JYVChip Resistor
R 0590 VRS-CZ1JF123JYVChip Resistor
R 9666 VRS-CZ1JF134FYVChip Resistor
R 9665 VRS-CZ1JF163FYVChip Resistor
R 9637 VRS-CZ1JF183FYVChip Resistor
R 9647 VRS-CZ1JF184JYVChip Resistor
R 9623 VRS-CZ1JF200JYVChip Resistor
R 9624 VRS-CZ1JF200JYVChip Resistor
R 9625 VRS-CZ1JF200JYVChip Resistor
R 9667 VRS-CZ1JF200JYVChip Resistor
R 9622 VRS-CZ1JF203FYVChip Resistor
R 9620 VRS-CZ1JF204FYVChip Resistor
R 3413 VRS-CZ1JF220JYVChip Resistor
R 3414 VRS-CZ1JF220JYVChip Resistor
R 3415 VRS-CZ1JF220JYVChip Resistor
R 3416 VRS-CZ1JF220JYVChip Resistor
R 3530 VRS-CZ1JF220JYVChip Resistor
R 3531 VRS-CZ1JF220JYVChip Resistor
R 1766 VRS-CZ1JF222FYVChip Resistor
R 0610 VRS-CZ1JF222JYVChip Resistor
R 0611 VRS-CZ1JF222JYVChip Resistor
R 1753 VRS-CZ1JF222JYVChip Resistor
R 3439 VRS-CZ1JF223JYVChip Resistor
R 1793 VRS-CZ1JF224JYVChip Resistor
R 3304 VRS-CZ1JF224JYVChip Resistor
R 3305 VRS-CZ1JF224JYVChip Resistor
R 3320 VRS-CZ1JF224JYVChip Resistor
R 3323 VRS-CZ1JF224JYVChip Resistor
R 3503 VRS-CZ1JF241FYVChip Resistor
R 1527 VRS-CZ1JF271JYVChip Resistor
R 3324 VRS-CZ1JF272FYVChip Resistor
R 3362 VRS-CZ1JF272JYVChip Resistor
R 0573 VRS-CZ1JF273JYVChip Resistor
R 0574 VRS-CZ1JF273JYVChip Resistor
DESCRIPTION
7
Page 73
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
R 9608 VRS-CZ1JF303JYVChip Resistor
R 9662 VRS-CZ1JF303JYVChip Resistor
R 1522 VRS-CZ1JF304JYVChip Resistor
R 0505 VRS-CZ1JF330JYVChip Resistor
R 0508 VRS-CZ1JF330JYVChip Resistor
R 3307 VRS-CZ1JF330JYVChip Resistor
R 3331 VRS-CZ1JF330JYVChip Resistor
R 3333 VRS-CZ1JF330JYVChip Resistor
R 3334 VRS-CZ1JF330JYVChip Resistor
R 3335 VRS-CZ1JF330JYVChip Resistor
R 3443 VRS-CZ1JF330JYVChip Resistor
R 3445 VRS-CZ1JF330JYVChip Resistor
R 3446 VRS-CZ1JF330JYVChip Resistor
R 9614 VRS-CZ1JF332FYVChip Resistor
R 0502 VRS-CZ1JF333JYVChip Resistor
R 9670 VRS-CZ1JF392FYVChip Resistor
R 9657 VRS-CZ1JF392JYVChip Resistor
R 9629 VRS-CZ1JF393FYVChip Resistor
R 1531 VRS-CZ1JF433JYVChip Resistor
R 1117 VRS-CZ1JF471JYVChip Resistor
R 1764 VRS-CZ1JF472FYVChip Resistor
R 1799 VRS-CZ1JF472FYVChip Resistor
R 0607 VRS-CZ1JF472JYVChip Resistor
R 0608 VRS-CZ1JF472JYVChip Resistor
R 3117 VRS-CZ1JF472JYVChip Resistor
R 3301 VRS-CZ1JF472JYVChip Resistor
R 3306 VRS-CZ1JF472JYVChip Resistor
R 3317 VRS-CZ1JF472JYVChip Resistor
R 3318 VRS-CZ1JF472JYVChip Resistor
R 3338 VRS-CZ1JF472JYVChip Resistor
R 3347 VRS-CZ1JF472JYVChip Resistor
R 3355 VRS-CZ1JF472JYVChip Resistor
R 3359 VRS-CZ1JF472JYVChip Resistor
R 3426 VRS-CZ1JF472JYVChip Resistor
R 9602 VRS-CZ1JF472JYVChip Resistor
R 9618 VRS-CZ1JF472JYVChip Resistor
R 9626 VRS-CZ1JF472JYVChip Resistor
R 1511 VRS-CZ1JF473JYVChip Resistor
R 1513 VRS-CZ1JF473JYVChip Resistor
R 1529 VRS-CZ1JF473JYVChip Resistor
R 1556 VRS-CZ1JF473JYVChip Resistor
R 1711 VRS-CZ1JF473JYVChip Resistor
R 1798 VRS-CZ1JF473JYVChip Resistor
R 9609 VRS-CZ1JF473JYVChip Resistor
R 3420 VRS-CZ1JF4R7JYVChip Resistor
R 3421 VRS-CZ1JF4R7JYVChip Resistor
R 3506 VRS-CZ1JF560JYVChip Resistor
R 3507 VRS-CZ1JF560JYVChip Resistor
R 9650 VRS-CZ1JF561FYVChip Resistor
R 0503 VRS-CZ1JF562JYVChip Resistor
R 9615 VRS-CZ1JF563FYVChip Resistor
R 3397 VRS-CZ1JF5R1JYVChip Resistor
R 3398 VRS-CZ1JF5R1JYVChip Resistor
R 3399 VRS-CZ1JF5R1JYVChip Resistor
R 3400 VRS-CZ1JF5R1JYVChip Resistor
R 3401 VRS-CZ1JF5R1JYVChip Resistor
R 3402 VRS-CZ1JF5R1JYVChip Resistor
R 3403 VRS-CZ1JF5R1JYVChip Resistor
R 3404 VRS-CZ1JF5R1JYVChip Resistor
R 3418 VRS-CZ1JF5R1JYVChip Resistor
R 3419 VRS-CZ1JF5R1JYVChip Resistor
R 3422 VRS-CZ1JF5R1JYVChip Resistor
R 3423 VRS-CZ1JF5R1JYVChip Resistor
R 3427 VRS-CZ1JF5R1JYVChip Resistor
R 3428 VRS-CZ1JF5R1JYVChip Resistor
R 9691 VRS-CZ1JF5R1JYVChip Resistor
R 9692 VRS-CZ1JF5R1JYVChip Resistor
R 9693 VRS-CZ1JF5R1JYVChip Resistor
R 9694 VRS-CZ1JF5R1JYVChip Resistor
R 9695 VRS-CZ1JF5R1JYVChip Resistor
R 9696 VRS-CZ1JF5R1JYVChip Resistor
R 9697 VRS-CZ1JF5R1JYVChip Resistor
R 9698 VRS-CZ1JF5R1JYVChip Resistor
R 9613 VRS-CZ1JF622JYVChip Resistor
R 9631 VRS-CZ1JF623FYVChip Resistor
R 9643 VRS-CZ1JF623FYVChip Resistor
R 3310 VRS-CZ1JF680JYVChip Resistor
R 3336 VRS-CZ1JF680JYVChip Resistor
R 3447 VRS-CZ1JF680JYVChip Resistor
R 3341 VRS-CZ1JF681JYVChip Resistor
R 1765 VRS-CZ1JF682FYVChip Resistor
R 1752 VRS-CZ1JF682JYVChip Resistor
R 1712 VRS-CZ1JF683FYVChip Resistor
R 1794 VRS-CZ1JF683FYVChip Resistor
R 1795 VRS-CZ1JF683FYVChip Resistor
DESCRIPTION
8
Page 74
LC-32LE265T / LC-40LE265T
NO.PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
RANK
[3] DKEYMG567FM02 / 01 (MAIN Unit)
R 1717 VRS-CZ1JF752JYVChip Resistor
R 1528 VRS-CZ1JF820JYVChip Resistor
R 0101 VRS-CZ1JF822JYVChip Resistor
R 0103 VRS-CZ1JF822JYVChip Resistor
R 9638 VRS-CZ1JF823FYVChip Resistor
R 9669 VRS-CZ1JF823FYVChip Resistor
R 9610 VRS-CZ1JF913JYVChip Resistor
R 9612 VRS-CZ1JF913JYVChip Resistor
R 9616 VRS-CZ1JF913JYVChip Resistor
R 9684 VRS-TQ2EF000JYVChip Resistor
R 1532 VRS-TQ2EF4R7JYVChip Resistor
R 0533 VRS-TQ2EF750JYVChip Resistor
R 0547 VRS-TQ2EF750JYVChip Resistor
R 0548 VRS-TQ2EF750JYVChip Resistor
R 0549 VRS-TQ2EF750JYVChip Resistor
R 0582 VRS-TQ2EF750JYVChip Resistor
R 0583 VRS-TQ2EF750JYVChip Resistor
R 0584 VRS-TQ2EF750JYVChip Resistor
R 1553 VRS-TV1JD000JYVChip Resistor
R 0550 VRS-TV1JD101JYVChip Resistor
R 0551 VRS-TV1JD101JYVChip Resistor
R 0552 VRS-TV1JD101JYVChip Resistor
R 0526 VRS-TW2ED101JYVChip Resistor
R 0528 VRS-TW2ED101JYVChip Resistor
6 CHLDZC286WJ01VP FRAME ASSEMBLY
6-1 LHLDZC286WJ4AVP FRAME
6-2 PSPAGB324WJZZVPORON H (x2)
6-3 PSPAGB325WJZZVPORON V (x2)
7 LHLDZC214WJ4BVSUPPORT PIN
8 LX-BZA556WJZZVBEZEL SCREW
9 PCOVUA252WJZZVDIFFUSION PLATE
10 PMIR-A369WJ4AVREFLECTION SHT
11 PSHEPB394WJZZVDIFFUSION SHEET
12 PSHEPB395WJZZVPRISM SHEET H
13 PSHEPB396WJZZVPRISM SHEET V
14 QCNW-P258WJPZVLED BL WIRE
15 R1LK315T3HB60WVPANEL HIRAKI
16 RUNTKB283WJZZVLED BAR (A)
17 RUNTKB284WJZZVLED BAR (B)
18 ZTAPEP109020EVYELLOW TAPE
19 ZTAPES18T030EVTAPE
[9] SUPPLIED ACCESSORIES
Supplied accessories
Remote control unit
X1
launam noitarepO
“AAA” size battery (g2)
X2
tinu dnatS
X3
X4
Stand base
NO.PARTS CODE
PRICE
RANK
[9] SUPPLIED ACCESSORIES
X1 R RMCGB149WJSAVREMOTE CONTROL
X2 -VBATTERY (X2)
X3 T INS-G356WJZZVOPERATION MANUAL (Z)
X4 C DAI-A977WJ01VKS STAND (LC-40LE265T)
X4 C DAI-A975WJ01KS STAND (LC-32LE265T)
X5 L X-BZA385WJF8VSCREW FOR STAND (X8)
X6 G DAI-A963WJ4WVSUPPORTING POST
X7 T GAN-C100WJZZVWARRANTY CARD (LC-40LE265T )
X7 T GAN-C101WJZZVWARRANTY CARD (LC-32LE265T )
No part of this publication may be reproduced,stored in a retrieval system, or transmitted inany form or by any means, electronic, mechanical,photocopying, recording, or otherwise, withoutprior written permission of the publisher.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.