In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
OUTLINE
This model is based on the LC-26/32GA5U and is changed some par ts. This Service Manual covers the
modifications alone. For the other points, refer to the LC-26/32GA5U Service Manual.
CONTENTS
» LIST OF CHANGED PARTS ..........................................................................................................................2
» IMPORTANT SERVICE SAFETY PRECAUTION .......................................................................................5
» PARTS LIST..............................................................................................................................................17
» PACKING OF THE SET............................................................................................................................27
LC-32GA5T/D
Page
SHARP CORPORATION
Page 2
LC-26GA5T
LC-32GA5T/D
LIST OF CHANGED PARTS
LC-26GA5U → LC-26GA5T
Ref.No.DescriptionLC-26GA5ULC-26GA5TNote
PWB ASSEMBLIES
AV UnitDUNTKC790WEV2No Parts Changed
R/C, LED UnitDUNTKC791WEV0No Parts Changed
KEY UnitDUNTKC792WEV0No Parts Changed
LCD CONTROL UnitDUNTKC793FE21No Parts Changed
MAIN UnitDUNTKC794FE01No Parts Changed
CPU UnitDUNTKC796FE11No Parts Changed
INVERTER UnitRUNTKA094WJZZNo Parts Changed
INVERTER-GND UnitRUNTKA095WJZZNo Parts Changed
POWER UnitRDENCA092WJZZNo Parts Changed
LCD PANEL
26" Wide LCD Panel UnitRLCDTA039WJZZ
CABINET AND MECHANICAL PARTS
Please refer to a Parts list. (Some Parts Changed)
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list. (Some Parts Changed)
2
Page 3
LIST OF CHANGED PARTS
LC-32GA5U → LC-32GA5T
Ref.No.DescriptionLC-32GA5ULC-32GA5TNote
PWB ASSEMBLIES
AV UnitDUNTKC790WEV2No Parts Changed
R/C, LED UnitDUNTKC791WEV0No Parts Changed
KEY UnitDUNTKC792WEV0No Parts Changed
LCD CONTROL UnitDUNTKC793FE22No Parts Changed
MAIN UnitDUNTKC794FE01No Parts Changed
CPU UnitDUNTKC796FE12No Parts Changed
INVERTER-1 UnitRUNTKA096WJZZNo Parts Changed
INVERTER-2 UnitRUNTKA097WJZZNo Parts Changed
INVERTER-GND UnitRUNTKA098WJZZNo Parts Changed
POWER UnitRDENCA093WJZZNo Parts Changed
CABINET AND MECHANICAL PARTS
Please refer to a Parts list. (Some Parts Changed)
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list. (Some Parts Changed)
3
Page 4
LC-26GA5T
LC-32GA5T/D
LIST OF CHANGED PARTS
LC-32GA5U → LC-32GA5D
Ref.No.DescriptionLC-32GA5ULC-32GA5DNote
PWB ASSEMBLIES
AV UnitDUNTKC790WEV2No Parts Changed
R/C, LED UnitDUNTKC791WEV0No Parts Changed
KEY UnitDUNTKC792WEV0No Parts Changed
LCD CONTROL UnitDUNTKC793FE22DUNTKC793DE22No Parts Changed
MAIN UnitDUNTKC794FE01No Parts Changed
CPU UnitDUNTKC796FE12No Parts Changed
INVERTER-1 UnitRUNTKA096WJZZRUNTKA164WJZZSome Parts Changed
INVERTER-2 UnitRUNTKA097WJZZRUNTKA165WJZZSome Parts Changed
INVERTER-GND UnitRUNTKA098WJZZRUNTKA166WJZZSome Parts Changed
POWER UnitRDENCA093WJZZNo Parts Changed
CABINET AND MECHANICAL PARTS
Please refer to a Parts list. (Some Parts Changed)
PACKING PARTS AND ACCESSORIES
Please refer to a Parts list. (Some Parts Changed)
4
Page 5
LC-26GA5T
2
2
2
2
LC-32GA5T/D
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
CAUTION: FOR CONTINUED PROTECTION
AGAINST A RISK OF FIRE REPLACE ONLY WITH
SAME TYPE FUSE.
LC-26GA5T:F701, F702 (3.15A, 250V)
LC-32GA5T/D:F701, F702 (4A, 250V)
F703 (2A, 250V), F704 (117°C, 2A) F705 (1A,
DC450V)
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks:
1. Inspect all lead dress to make certain that leads are
not pinched, and check that hardware is not lodged
between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
» Plug the AC cord directly into a 110 (220 Korea) volt
AC outlet.
» Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to an earth ground.
» Use an AC voltmeter ha ving with 5000 ohm per v olt,
or higher, sensitivity or measure the A C v oltage drop
across the resistor.
» Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
All checks must be repeated with the AC cord plug
connection reversed. (If necessary, a nonpolarized
adaptor plug must be used only for the purpose of
completing these checks.)
Any reading of 0.75 Vrms (this corresponds to 0.5
mA rms AC.) or more is excessive and indicates a
potential shock hazard which must be corrected
before returning the monitor to the owner.
Many electrical and mechanical parts in LCD color
television have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified b y " å"
For continued protection, replacement parts must be
identical to those used in the original circuit.
The use of a substitute replacement parts which do not
have the same safety characteristics as the factory
recommended replacement parts shown in this service
manual, may create shock, fire or other hazards.
5
and
Page 6
LC-26GA5T
LC-32GA5T/D
Precautions for using lead-free solder
1 Employing lead-free solder
"PWBs" of this model employs lead-free solder. The LF symbol indicates lead-free solder, and is attached on the
PWBs and service manuals. The alphabetical character following LF shows the type of lead-free solder.
Example:
LFa
Indicates lead-free solder of tin, silver and copper.
2 Using lead-free wire solder
When fixing the PWB soldered with the lead-free solder, apply lead-free wire solder. Repairing with conventional
lead wire solder may cause damage or accident due to cracks.
As the melting point of lead-free solder (Sn-Ag-Cu) is higher than the lead wire solder by 40°C, we recommend
you to use a dedicated soldering bit, if you are not familiar with ho w to obtain lead-free wire solder or soldering bit,
contact our service station or service branch in your area.
3 Soldering
As the melting point of lead-free solder (Sn-Ag-Cu) is about 220°C which is higher than the conventional lead
solder by 40°C, and as it has poor solder wettability, you may be apt to keep the soldering bit in contact with the
PWB for extended period of time. However, Since the land may be peeled off or the maximum heat-resistance
temperature of parts may be exceeded, remov e the bit from the PWB as soon as y ou confirm the steady soldering
condition.
Lead-free solder contains more tin, and the end of the soldering bit may be easily corroded. Make sure to turn on
and off the power of the bit as required.
If a different type of solder stays on the tip of the soldering bit, it is allo y ed with lead-free solder. Clean the bit after
every use of it.
When the tip of the soldering bit is blackened during use, file it with steel wool or fine sandpaper.
Be careful when replacing parts with polarity indication on the PWB silk.
Lead-free wire solder for servicing
Part No,★DescriptionCode
ZHNDAi123250EJφ0.3mm250g(1roll)BL
ZHNDAi126500EJφ0.6mm500g(1roll)BK
ZHNDAi12801KEJφ1.0mm1kg(1roll)BM
6
Page 7
SPECIFICATIONS
LC-26GA5T
LC-32GA5T/D
Item26"LIQUID CRYSTAL TELEVISION,
Model: LC-26GA5T
LCD panel
Number of dots3,147,264 dots (1366 768 × 3 dots)
TV
Function
Brightness450 cd/m
Viewing anglesH : 170° V : 170°
Audio amplifier10W × 2
SpeakersØ 8cm 2pcs, Ø 2.5cm 2pcs
TerminalsAV in, COMPONENT in
TV-standard (CCIR)
Receiving
Channel
Audio multiplexBTSC System
RearINPUT 1
INPUT 2
INPUT 4
INPUT 5DVI-I in, Audio in
VHF/UHF
CATV1-125ch
INPUT 3
26" Advanced Super View & BLACK TFT LCD
×
American TV Standard NTSC System
VHF 2-13ch, UHF 14-69ch
2
AV in, COMPONENT in
S-VIDEO in, AV in
HDMI in
32" LIQUID CRYSTAL TELEVISION,
Model: LC-32GA5T/D
32" Advanced Super View & BLACK TFT LCD
ANTENNA75 Ω Unbalance, F Type for VHF/UHF/CATV in × 1
MONITOR OUTPUT
OSD languageEnglish/Fr
Power Requirement
Power Consumption
Weight
AccessoriesOperation manual (× 1), Remote control unit (× 1), AC cord (×1), “AAA” size
LC-32GA5T/D
AC 110 V, 60 Hz (T) / AC 220 V, 60 Hz (D)
140 W (0.3 W Standby with AC 110 V) (T)
140 W (0.3 W Standby with AC 220 V) (D)
36.4 lbs./16.5 kg (w/o stand),
45.2 lbs./20.5 kg (with stand)
Specifications are subject to change without prior notice.
7
Page 8
LC-26GA5T
LC-32GA5T/D
- M E M O -
8
Page 9
DESCRIPTION OF SCHEMATIC DIAGRAM
VOLTAGE MEASUREMENT CONDITION:
The voltages at test points are measured on
1.
exclusive AC adaptor and the stable supply
voltage of AC 120V. Signals are fed by a color bar
signal generator for servicing purpose and the
above voltages are measured with a 20k ohm/V
tester.
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1. The unit of resistance "Ω" is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(K= ± 10%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/16W, unless otherwise noted.
LC-26GA5T
LC-32GA5T/D
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
CAUTION:
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
DISCONNECT THE AC PLUG FROM THE AC
1.
OUTLET BEFORE REPLACING PARTS.
SEMICONDUCTOR HEAT SINKS SHOULD BE
2.
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH " " ( ) ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES " " ( ) SONT
IMPORTANTES POUR MAINTENIR LA SECURITE
DE L'APPAREIL.
NE REMPLACER CES PIEDES QUE PAR DES
PIECES DONT LE NUMERO EST SPECIFIE POUR
MAINTENIR LA SECURITE ET PROTEGER LE
BON FONCTIONNEMENT DE L'APPAREIL.
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such f eatures
are identified by å and shaded areas in the Replacement Parts Lists
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please furnish the
following informations.
1. MODEL NUMBER2. REF. NO.
3. PART NO.4. DESCRIPTION
★ MARK: SPARE PARTS-DELIVERY SECTION
Ref. No.Part No.★DescriptionCode
PRINTED WIRING BOARD ASSEMBLIES
(NOT REPLACEMENT ITEM)
LC-26GA5T
DUNTKC790WEV2 – AV Unit—
DUNTKC791WEV0 – R/C, LED Unit—
DUNTKC792WEV0 – KEY Unit—
DUNTKC793FE21J LCD CONTROL UnitCC
DUNTKC794FE01J MAIN UnitCK
DUNTKC796FE11– CPU Unit—
RUNTKA094WJZZ– INVERTER Unit—
RUNTKA095WJZZ– INVERTER-GND Unit—
RDENCA092WJZZ – POWER Unit—
LC-32GA5T
DUNTKC790WEV2 – AV Unit—
DUNTKC791WEV0 – R/C, LED Unit—
DUNTKC792WEV0 – KEY Unit—
DUNTKC793FE22J LCD CONTROL UnitCC
DUNTKC794FE01J MAIN UnitCK
DUNTKC796FE12– CPU Unit—
RUNTKA096WJZZ– INVERTER-1 Unit—
RUNTKA097WJZZ– INVERTER-2 Unit—
RUNTKA098WJZZ– INVERTER-GND Unit—
RDENCA093WJZZ – POWER Unit—
LCD PANEL
NOTE: THE PARTS HERE SHOWN ARE SUPPLIED AS AN
ASSEMBLY BUT NOT INDEPENDENTLY.
RLCDTA039WJZZJ 26" Wide LCD Panel UnitDQ
(LC-26GA5T)
RLCDTA041WJZZJ 32" Wide LCD Panel UnitEG
(LC-32GA5T)
RLCDTA082WJZZJ 32" Wide LCD Panel UnitDM
(LC-32GA5D)
DUNTKC793FE52 (LC-32GA5D)
LCD CONTROL Unit
INTEGRATED CIRCUITS
IC4903 RH-iXB435WJZZYJ 25LC320-I/SNGAH
RESISTORS
R4118 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R4124 VRS-CY1JF562FYJ 5.6k 1/16W Metal Oxide AA
R4134 VRS-CY1JF101FYJ 100 1/16W Metal Oxide AD
R4137 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R4138 VRS-CY1JF911FYJ 910 1/16W Metal Oxide AA
R4141 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R4142 VRS-CY1JF272FYJ 2.7k 1/16W Metal Oxide AA
R4144 VRS-CY1JF153FYJ 15k 1/16W Metal Oxide AA
R4145 VRS-CY1JF132FYJ 1.3k 1/16W Metal Oxide AA
R4149 VRS-CY1JF243FYJ 24k 1/16W Metal Oxide AA
R4150 VRS-CY1JF222FYJ 2.2k 1/16W Metal Oxide AA
R4152 VRS-CY1JF393FYJ 39k 1/16W Metal Oxide AA
R4153 VRS-CY1JF363FYJ 36k 1/16W Metal Oxide AA
R4154 VRS-CY1JF272FYJ 2.7k 1/16W Metal Oxide AA
R4159 VRS-CY1JF162FYJ 1.6k 1/16W Metal Oxide AA
R4164 VRS-CY1JF182FYJ 1.8k 1/16W Metal Oxide AA
R4169 VRS-CY1JF122FYJ 1.2k 1/16W Metal Oxide AA
R4171 VRS-CY1JF333FYJ 33k 1/16W Metal Oxide AA
R4172 VRS-CY1JF562FYJ 5.6k 1/16W Metal Oxide AA
R4176 VRS-CY1JF681FYJ 680 1/16W Metal Oxide AA
R4183 VRS-CY1JF223FYJ 22k 1/16W Metal Oxide AA
R4190 VRS-CY1JF683FYJ 68k 1/16W Metal Oxide AA
R4192 VRS-CY1JF473FYJ 47k 1/16W Metal Oxide AA
R4203 VRS-CY1JF152FYJ 1.5k 1/16W Metal Oxide AA
R4205 VRS-CY1JF821FYJ 820 1/16W Metal Oxide AA
R4230 VRS-CY1JF911FYJ 910 1/16W Metal Oxide AA
DUNTKC790WEV2 – AV Unit—
LC-32GA5D
DUNTKC791WEV0 – R/C, LED Unit—
DUNTKC792WEV0 – KEY Unit—
DUNTKC793DE22J LCD CONTROL UnitCC
DUNTKC794FE01J MAIN UnitCK
DUNTKC796FE12– CPU Unit—
RUNTKA164WJZZ– INVERTER-1 Unit—
RUNTKA165WJZZ– INVERTER-2 Unit—
RUNTKA166WJZZ– INVERTER-GND Unit—
RDENCA093WJZZ – POWER Unit—
R7601 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7603 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7606 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7607 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7609 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7612 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7613 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7615 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7618 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7619 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7621 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7624 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7625 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7627 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7630 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7631 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7633 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7636 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7637 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7639 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7642 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7643 VRS-CY1JD102FJ 1k1/10W Metal Oxide AA
R7645 VRS-CY1JD242FJ 2.4k 1/10W Metal Oxide AA
R7646 VRS-CY1JD242FJ 2.4k 1/10W Metal Oxide AA
R7647 VRS-CY1JD513JJ 51k 1/10W Metal Oxide AA
R7649 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7651 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7654 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7655 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7657 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7660 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7661 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7663 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7666 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7667 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7669 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7672 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7673 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7675 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7678 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7679 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7681 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7684 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7685 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7687 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7690 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
R7691 VRS-CY1JD821JJ 820 1/10W Metal Oxide
R7693 VRS-CY1JD155JJ 1.5M1/10W Metal Oxide AA
R7696 VRS-TP2BD104JJ 100k 1/4WMetal Oxide AA
CN7601 QCNCM1855SNEZ J Connector, 4Pin
MISCELLANEOUS PARTS
CN7602 QCNCM1821SNEZ J Connector, 2PinAD
CN7603 QCNCM1821SNEZ J Connector, 2PinAD
CN7604 QCNCM1821SNEZ J Connector, 2PinAD
CN7605 QCNCM1821SNEZ J Connector, 2PinAD
CN7606 QCNCM1821SNEZ J Connector, 2PinAD
CN7607 QCNCM1821SNEZ J Connector, 2PinAD
CN7608 QCNCM1821SNEZ J Connector, 2PinAD
CN7609 QCNCM1821SNEZ J Connector, 2PinAD
JP7601 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7602 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7603 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7604 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7605 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7606 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7607 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7608 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7609 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7610 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7611 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7612 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7613 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7614 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7615 VRS-TP2BD000JJ 01/4WMetal Oxide AA
JP7616 VRS-TP2BD000JJ 01/4WMetal Oxide AA
LUG7601
LUG7602
LUG7606
3
3-1CCOVAB012WJ01J Stand Hinge Ass’yBF
3-1-1
3-1-2GDAi-A148WJSAJ Stand Support
3-1-3GDAi-A160WJF7J Support Cover
3-1-4LANGTA156WJSAJ Stand Bracket
3-1-5LX-BZA046WJFNJ Screw, x2AA
3-1-6LX-BZA091WJF7J Screw, x4
3-1-7XCSS940P25000J Screw, x5AB
3-2CDAi-A147WJ01J Stand Base Ass’yBH
3-2-1
3-2-2LANGKA282WJSAJ Base AngleBF
3-2-3PSPAZA476WJZZJ Leg Spacer-A, x4AC
3-2-4PSPAZA477WJZZJ Leg Spacer-B, x2AD
3-2-5PSPAZA530WJZZJ Leg Spacer-C, x2AD
3-2-6XEBS940P10000J Screw, x10AB
3-3XCBS940P25000J Screw, x5AB
4CCOVAA873WJ04J Top Cover Ass’yAX
4-1
4-2JBTN-A254WJKBJ Power ButtonAG
4-3JBTN-A259WJKBJ Operation ButtonAH
4-4MSPRCA015WJFW J Spring, for Power ButtonAB
4-5PZETKA115WJZZJ Spacer
4-6XEBSN30P08000J Screw, x2AA
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
TQ1913-S
Jul 2005 Printed in Japan
Design and Production Information
Design: Japan
Production : Japan
SY. KD
SHARP CORPORATION
AV Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.