In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
TERMINAL UNIT ....................................... 42
Ë
INVERTER UNIT ....................................... 43
Ë
OPERATION UNIT .................................... 44
Ë
CABINET AND MECHANICAL PARTS ..... 44
Ë
ACCESSORIES PARTS ............................ 46
Ë
PACKING PARTS ...................................... 46
» PACKING OF THE SET................................... 47
SHARP CORPORATION
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
1
Page 2
LC-20A2U
2
2
IMPORTANT SERVICE SAFETY PRECAUTION
Ë
Service work should be perfomed only by qualified service technicians who are thoroughly
familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
CAUTION: FOR CONTINUED
PROTECTION A GAINST A RISK OF
FIRE REPLACE ONLY WITH SAME
TYPE FUSE. F3701 (2.5A, 125V),
A V
F3702 (3.15A, 125V), F7751 (6.0A,
125V) FUSE.
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks:
1. Inspect all lead dress to make certain that leads are
not pinched, and check that hardware is not lodged
between the chassis and other metal parts in the
receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulation materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacitor networks, mechanical
insulators and etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
• Plug the AC cord directly into a 110~240 volt A C outlet,
and connect the DC power cable into the receiver's
DC jack. (Do not use an isolation transformer for this
test).
• Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series with
all exposed metal cabinet parts and a known earth
ground, such as electrical conduit or electrical ground
connected to an earth ground.
• Use an AC voltmeter ha ving with 5000 ohm per volt, or
higher, sensitivity or measure the AC voltage drop
across the resisor.
• Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon and etc.) and measure the AC voltage drop
across the resistor.
All checks must be repeated with the AC cord plug
connection reversed. (If necessary, a nonpolarized
adaptor plug must be used only for the purpose of
completing these checks.)
Any reading of 35V peak (this corresponds to 0.7
milliamp. peak A C .) or more is e xcessive and indicates
a potential shock hazard which must be corrected
before returning the monitor to the owner .
Many electrical and mechanical parts in LCD television
have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage and etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
and shaded areas in the
Schematic Diagrams
For continued protection, replacement parts must be
identical to those used in the original circuit.
The use of a substitute replacement parts which do not
have the same safety characteristics as the factory
recommended replacement parts shown in this service
manual, may create shock, fire or other hazards.
components having such features are identified by “ å”
Ne peut effectuer la réparation qu' un technicien spécialisé qui s'est parfaitement
accoutumé à toute vérification de sécurité et aux conseils suivants.
AVERTISSEMENT
• Utiliser un voltmètre CA d'une sensibilité d'au moins
5000Ω/V pour mesurer la chute de tension en travers
1. N'entreprendre aucune modification de tout circuit.
C'est dangereux.
2. Débrancher le récepteur avant toute réparation.
de la résistance.
• Toucher avec la sonde d'essai les pièces métalliques
exposées qui présentent une voie de retour au châssis
(antenne, coffret métallique, tête des vis, arbres de
PRECAUTION: POUR LA
PROTECTION CONTINUE CONTRE
LES RISQUES D'INCENDIE,
REMPLACER LE FUSIBLE PAR UN
A V
FUSIBLE DE MEME TYPE F3701
(2.5A, 125V), F3702 (3.15A, 125V),
F7751 (6.0A, 125V).
VERIFICATIONS CONTRE L'INCEN-DIE ET
LE CHOC ELECTRIQUE
Avant de rendre le récepteur à l'utilisateur, effectuer
commande et des boutons, écusson, etc.) et mesurer
la chute de tension CA en-travers de la résistance.
Toutes les vérifications doivent être refaites après avoir
inversé la fiche du cordon d'alimentation. (Si
nécessaire, une prise d'adpatation non polarisée peut
être utilisée dans le but de terminer ces vérifications.)
Tous les courants mesurés ne doivent pas dépasser
0,5 mA.
Dans le cas contraire, il y a une possibilité de choc
électrique qui doit être supprimée avant de rendre le
récepteur au client.
les vérifications suivantes.
1. Inspecter tous les faisceaux de câbles pour s'assurer
que les fils ne soient pas pincés ou qu'un outil ne soit
pas placé entre le châssis et les autres pièces
métalliques du récepteur.
DVM
2. Inspecter tous les dispositifs de protection comme les
boutons de commande non-métalliques, les isolants,
le dos du coffret, les couvercles ou blindages de réglage
et de compartiment, les réseaux de résistance-capacité,
VTVM
AC SCALE
ECHELLE CA
50k ohm
10W
les isolateurs mécaniques, etc.
3. S'assurer qu'il n'y ait pas de danger d'électrocution en
vérifiant la fuite de courant, de la facon suivante:
• Brancher le cordon d'alimentation directem-ent à une
prise de courant de 110-240V. (Ne pas utiliser de
transformateur d'isolation pour cet essai).
0.15 µF
0.15µF
TEST PROBE
SONDE D'ESSAI
• A l'aide de deux fils à pinces, brancher une résistance
de 1,5 kΩ 10 watts en parallèle avec un condensateur
de 0,15µF en série avec toutes les pièces métalliques
exposées du coffret et une terre connue comme une
conduite électrique ou une prise de terre branchée à la
De nombreuses pièces, électriques et mécaniques,
dans les téléviseurs présentent des caractéristiques
spéciales relatives à la sécurité, qui ne sont souvent
pas évidentes à vue. Le degré de protection ne peut
pas être nécessairement augmentée en utilisant des
pièces de remplacement étalonnées pour haute tension,
puissance, etc.
Les pièces de remplacement qui présentent ces
caractéristiques sont identifiées dans ce manuel; les
pièces électriques qui présentent ces particularités sont
identifiées par la marque " å " et hachurées dans la
liste des pièces de remplacement et les diagrammes
schématiques.
Pour assurer la protection, ces pièces doivent être
identiques à celles utilisées dans le circuit d'origine.
L'utilisation de pièces qui n'ont pas les mêmes
caractéristiques que les pièces recommandées par
l'usine, indiquées dans ce manuel, peut provoquer des
électrocutions, incendies, radiations X ou autres
accidents.
3
Page 4
LC-20A2U
Specifications
4
Page 5
Operation Manual
LC-20A2U
5
Page 6
LC-20A2U
6
Page 7
Dimensions
LC-20A2U
(Unit: inch/mm)
7
Page 8
LC-20A2U
REMOVING OF MAJOR PARTS
1. Detach the terminal cover.
2. Remove the four lock screws from the table stand.
3. Remove the four lock screws each from the left and right speakers. Disconnect the connectors
and detach the speaker assemblies.
4. Remove the ten lock screws from the terminals.
5. Remove the five lock screws from the cabinet B.
6. Undo the nine hooks off the cabinet B: Press the hook
6-9
in this order. Detach the cabinet B.
7. Undo the six wire holders and peel off the 9 pieces of tape. Disconnect the connection
cables.
(Note: Some pieces of tape are located below the PWBs. To access such tape, detach the
PWBs, peel off the tape and disconnect the cables.)
8. Disconnect the connectors from the PWBs.
6-1
first and then the hooks
6-2
thru
3
Speaker (Right)
Connection Cable
Terminal PWB Holder
Speaker Assembly (Right)
Cabinet B
Cabinet A
SC1201
(MAIN Unit)
8
8
SC1202
P755
P754
P753
7
Tape
7
Tape
Tape
7
Tape
P701
P2001
P303
6-7
8
3
6-6
6-8
6-9
SC401
SC3401
SC3405
6-4
6-5
SC7001
(Y/C
SEPARATION
Unit)
P7102
P7101
P7301
P7305
(TERMINAL Unit)
P3701
5
4
6-3
P7753
(INVERTER
Unit)
8
P7755
P7751
P3206
Speaker Assembly (Left)
Terminal Cover
6-2
1
6-1
2
Table Stand (Cover)
Table Stand
8
7
Speaker (Left)
8
Connection Cable
Tape
7
(OPERATION Unit)
P4004
8
Tape
7
Page 9
9. Remove the four lock screws from the MAIN PWB.
10. Remove the four lock screws from the Y/C SEPARATION PWB.
11. Remove the three lock screws from the INVERTER PWB.
12. Remove the lock screw from the TERMINAL PWB and the lock screw from the grounding
terminal. Detach the reinforcement plate too.
13. Remove the two lock screws from the LCD display unit.
14. Remove the three lock screws from the OPERATION PWB.
Y/C SEPARATION Unit
9
10
11
INVERTER Unit
TERMINAL PWB Assembly
MAIN Unit
LC-20A2U
12
LCD Display Unit
13
12
14
OPERATION
Unit
13
Reinforcement
Plate
Cabinet A
9
Page 10
LC-20A2U
» Precautions in handling the LCD panels
1. Work in a clean room (with humidities below 50%).
2. Be sure to wear an anti-static armband.
3. Handle the panels on an electroconductive mat.
4. Be careful not to fall, shake and shock the panels.
15. Remove the four lock screws from the front of the LCD display unit and
the three lock screws from its back. Detach the shielding plate.
16. Detach the two reflection sheets.
17. Detach the top and bottom fluorescent lamps.
18. Remove the photoconductive plate.
19. Detach the top and bottom reflection sheets.
20. Detach the ITO sheet.
21. Detach the diffusion sheet and
reflection/deflection plate.
15
LCD Display Unit
(Front)
Lamp Reflector
(PSHEP0223CEZZ)
Photoconductive Plate
ITO Sheet
20
Fluorescent Lamp (Top)
(KLMP-0101CEZZ)
17
19
18
15
16
Reflection Sheet
(PSHEP0187CEZZ)
Reflection Sheet
17
(PSHEP0186CEZZ)
Fluorescent Lamp (Bottom)
(KLMP-0102CEZZ)
15
15
Shielding Plate
LCD Display Unit
21
Reflection/deflection Plate
Diffusion Sheet
10
Lamp Reflector (Bottom)
19
(PSHEP0224CEZZ)
Page 11
No picture
at all
Yes
No
Are inputs
and outputs
of IC802 as
specified?
Check all the settings on the microprocessor’s adjust process menu.
No picture
Check IC802
and its
peripheral
parts.
Yes
No
Are inputs
and outputs
of IC1201 as
specified?
Check
IC1201 and
its peripheral
parts.
Check LCD
panel voltage
and
waveform.
No TV and
VIDEO 1
output
Yes
No
Are inputs
and outputs
of IC402 as
specified?
Check IC402
and its
peripheral
parts.
No
Is input at pin
(73) of IC802
as specified?
Check IC802,
AV1 line and
their
peripheral
parts.
No TV
output
Yes
No
Are voltages
at pins (6),
(7) and (9) of
tuner as
specified?
Check the
power line.
Yes
No
Is output at
pin (19) of
tuner as
specified?
Check the
tuner and its
peripheral
parts.
No
Is input at pin
(1) of IC402
as specified?
Check the
line in
question.
Yes
Check IC402
and its
peripheral
parts.
Yes
No
Are pins (2)
and (4) of
IC402 at “H”
and “L”
respectively?
Are pins (65)
and (66) of
IC2001 at “H”
and “L”
respectively?
No VIDEO
1 output
Yes
No
Is input at pin
(1) of IC402
as specified?
Check the
line in
question.
Yes
No
Are pins (2)
and (4) of
IC402 both at
“L”?
No VIDEO
2 output
No
Is input at pin
(74) of IC802
as specified?
Check J3403,
AV2 line and
their
peripheral
parts.
No S
VIDEO
output
No
Are inputs at
pins (71) and
(72) of IC802
as specified?
Check
SC3301, SY
line, SC line
and
peripheral
parts.
No
COMPONENT
output
No
Is input at
pins (4), (5),
(6) and (75)
of IC802 as
specified?
Check J3405,
DVD-Y line,
CB line, CR
line and
peripheral
parts.
Are pins (65)
and (66) of
IC2001 both
at “L”?
Check IC402
and its
peripheral
parts.
Yes
Check the
line in
question.
Yes
Check the
line in
question.
TROUBLE SHOOTING TABLE
LC-20A2U
11
Page 12
LC-20A2U
No picture and sound
No color
No TV color
No S-VIDEO color
Yes
No
Do F3701 and F3702
function?
Check all the settings on the microprocessor
’s adjust process menu.
No
Are secondary outputs
(+38V, +16V, +9V, +5V, -8V)
of T701 as specified?
Yes
Are the oscillation waveform
at T701’s primary side as
specified?
Yes
No
Disconnect F3701 and
F3702. Is the load side
short-circuited?
Yes
No
Is any of T701’s primary side,
Q701, Q710 and S4701
short-circuited?
Check J3701, its peripheral
parts and connection cable.
Replace F3701 and F3702.
Check S4701 and
connection cable.
Check the secondary-side
load of T701.
Fluorescent lamp
Yes
No
Does F7751 function?
Yes
No
Is Pin (34) of IC1201 at
“H”?
Yes
No
Are the oscillation waveforms
at the primary side of T7751-6
as specified?
Yes
Replace F7751.
No
Is input at pin (71) of IC802
as specified?
Check SC3301, SC line and
peripheral parts.
Yes
Check the line, IC1201 and
its peripheral parts.
Check Q7751-5, T7751-6
and their peripheral parts.
Replace the fluorescent lamp
and check the oscillation
waveform again.
No VIDEO color
Check all the settings on the microprocessor
’s adjust process menu.
No COMPONENT color
No
Is input at pins (4) and (6) of
IC802 as specified?
Check J3405, CB line, CR
line and peripheral parts.
TROUBLE SHOOTING TABLE (Continued)
12
Page 13
No sound
from
speakers
Yes
No
Is pin (53) of
IC2001 at “L”?
Check all the settings on the microprocessor
’s adjust process menu.
No sound
No
Are outputs at
pins (1) and (7)
of IC903 as
specified?
Yes
No
Are inputs and
outputs of
IC303 as
specified?
Yes
No
Are inputs at
pins (11) and
(16) as well as
outputs at pins
(3) and (5), all
of IC7305, as
specified?
Muting effect is
on. Check the
FSMU line.
Check IC901,
IC903 and their
peripheral
parts.
Check IC303
and its
peripheral
parts.
Check the line
in question,
IC7305 and its
peripheral
parts.
Yes
Check the
speakers and
their peripheral
parts.
No sound
from
headphone
Yes
No
Is pin (55) of
IC2001 at “L”?
Check the
headphone and
its peripheral
parts.
Check Q306,
J4001 and their
peripheral
parts.
No sound
from output
line
Yes
No
Is pin (52) of
IC2001 at “L”?
No
Are outputs at
pins (1) and (7)
of IC902 as
specified?
Yes
Check the line
in question.
Check the
LMUTE line.
Check IC902
and its
peripheral
parts.
TV sound
failure
Yes
No
Is output at pin
(16) of tuner as
specified?
No
Is input at pin
(60) of IC901
as specified?
Check the
tuner and its
peripheral
parts.
Check IC901,
Q3301, Q3204,
Q3205 and
their peripheral
parts.
TROUBLE SHOOTING TABLE (Continued)
LC-20A2U
13
Page 14
LC-20A2U
ADJUSTMENT PROCEDURES
The product has been factory-adjusted to optimum settings. If by any chance any of the settings gets out of position
or when a part has been replaced, take the following procedures.
Preparations
Use the specific AC adaptor or a regulated DC power supply.
AC adaptor: UADP-0220CEZZ
DC power supply: 13 V, 4.2 A (monitor power 3.7 A, audio amplifier power 1.0 A)
1. Adjustment Procedures
1-1. Adjusting the checker
Turning on the power (getting initialized) → Selecting the model number and screen size (inches) →
Transferring the model-specified data to the setting EEPROM (I
Calling the adjustment process mode → +B adjustment
1-2. Making finish process adjustments
Turning on the power → Calling the adjustment process mode (with the remote controller) →
Adjusting the counter bias, TV contrast and white balance.
2. Calling the Adjustment Process Mode
There are two ways to enter this mode.
» Set the KEY4 (pin (81) of IC2001) and KEY5 (pin (82) of IC2001) to the L level and turn on the power.
» Hold down both the “TV/VIDEO” and “MENU” keys at once and turn on the main power. (Make sure “K”
appears at the top left of the screen, which means the set is in the inspection process mode.) Then press the
“CH "” and “VOL –” keys at once. To quit this mode, just turn off the main power. (The mode can be turned
off with the power switch either on the set or the remote controller.)
2
C) →
3. Key Operation in the Adjustment Process Mode
Selecting a receiving channel
» Select an actual receiving channel with the “CH "/'” keys.
Short push-in : Channels are selected one after another.
Long push-in : Channels are skipped up to the next receivable channel.
» Adjustments
All the items can be adjusted one by one with the “MENU”, “CH "/'” and “VOL + / –” keys (on the set and
the remote controller).
» The “MENU” key serves to toggle between adjustment items (the next item is selected).
Let’s suppose that the item at the bottom line is now selected. Press the “MENU” k ey and the item at the top
line on the next page will be selected.
» The “TV/VIDEO” key is also used to toggle between adjustment items.
Let’s suppose that the item at the top line is now selected. Press the “TV/VIDEO” key and the item at the
bottom line on the previous page will be selected.
» Let’s suppose that the PAL/NTSC is selected on pages 11 and 12. By pressing the “VOL + / –” keys, the
register selection mode is brought on and the cursor moves to the address 01.
» Using the “CH "/'” and “VOL + / –” keys, move the cursor vertically and horizontally, respectively. Use the
“12” key to enter the setting.
With an item selected, the cursor moves to its setting. Using the “VOL + / –” keys, the setting of the item
selected can be changed first for the left side. A new setting is now entered with the “12” k ey. Using the “VOL
+ / –” keys again, the right-side setting can also be changed.
0 ←→ 1 ←→ ...←→ 9 ←→ A ←→ ... ←→ F ←→ 0 ←→ ...
Enter the setting with the “12” key . Go back to the address selection and go to the next item with the “MENU”
key. The cursor moves for address selection as follows using the “VOL + / –” keys.
Example : 01←→ 02 ←→ 03 ←→ 01 ←→ ...
Similarly the cursor moves as follows with the “CH "/'” keys.
Example : 02 ←→ 05 ←→ ... ←→ F6 ←→ 02 ←→ ...
14
Page 15
4. Getting Initialized
4-1. Connect pins (81) and (82) of IC2001 to GND. Turn on the power.
4-2. Select the model number (A2U).
4-3. Select the screen size (20 inches).
Note: This procedure is needed only when the IC2001 or IC2004 (EEPROM) has been replaced.
5. Adjustments
5-1. +B adjustment (+B ADJ. on page 1)
1) Receive the color bar signal.
2) Adjust the voltage at pin (8) of P303 to 5.00 ±0.02 V.
Note: The 5.00 V level is used as reference to the supply voltage. Make an exact adjustment to 5.00 V.
5-2. Counter bias adjustment ...... “COM BIAS” on page 2
1) Adjust the COM BIAS setting until the contrast becomes maximum (down to the darkest black).
5-3. White balance adjustment
1) Receive the monoscope pattern signal.
2) Adjust so that the “RCUTOFF” and “BCUT OFF” settings on page 2 of the adjustment process are optimum.
Note: The “RCUTOFF” and “BCUTOFF” settings in the adjustment process should be in the range of -10
thru +10. If without this range, the variable user control range will be reduced.
6. Factory Settings
Holding down the “TV/VIDEO” and “MENU” keys of the set at once, turn on the main power (make sure “K”
appears at the top left of the screen). Then keep pressing the “CH '” and “V OL +” keys at once until “SETTING
COMPLETE” appears at the center of the screen.
Note: Just after the factory settings have been made, turn off the power switch.
(The next time the power is switched on, the set is designed to get started in the EZ SETUP mode. If
any other key is activated after making the factory settings, the set may fail to function as specified.)
LC-20A2U
15
Page 16
1716
LC-20A2U
121110987654321
A
B
C
D
E
F
G
H
CHASSIS LAYOUT
MAIN Unit (Side A)Y/C SEPARATION Unit (Side A)
MAIN Unit (Side B)Y/C SEPARATION Unit (Side B)
OPERATION Unit
INVERTER Unit
TERMINAL Unit
Page 17
1918
LC-20A2U
121110987654321
A
B
C
D
E
F
G
H
BLOCK DIAGRAM
Page 18
LC-20A2U
DESCRIPTION OF SCHEMATIC DIAGRAM
VOLTAGE MEASUREMENT CONDITION:
1. Voltages at test points are measured at the
supply voltage of AC 120V. Signals are fed by a
color bar signal generator for servicing purpose and
the above voltages are measured with a 20k ohm/
V tester.
WAVEFORM MEASUREMENT CONDITION:
1. Wavef orms at test points are observed at the supply
voltage of AC 120V. Signals are fed by a color bar
signal generator for servicing purpose.
INDICATION OF RESISTOR & CAPACITOR:
RESISTOR
1. The unit of resistance “Ω” is omitted.
(K=kΩ=1000 Ω, M=MΩ).
2. All resistors are ± 5%, unless otherwise noted.
(J= ± 5%, F= ± 1%, D= ± 0.5%)
3. All resistors are 1/10W, unless otherwise noted.
4. All resistors are Carbon type, unless otherwise
noted.
C : Solid
S : Oxide FilmT : Special
N : Metal Coating
CAPACITOR
1. All capacitors are µF, unless otherwise noted.
(P=pF=µµF).
2. All capacitors are 50V, unless otherwise noted.
3. All capacitors are Ceramic type, unless otherwise
noted.
This circuit diagram is original one, therefore there may be a
slight difference from yours.
SAFETY NOTES:
1. DISCONNECT THE AC PLUG FROM THE AC
OUTLET BEFORE REPLACEING PARTS.
2. SEMICONDUCTOR HEAT SINKS SHOULD BE
REGARDED AS POTENTIAL SHOCK HAZARDS
WHEN THE CHASSIS IS OPERATING.
IMPORTANT SAFETY NOTICE:
PARTS MARKED WITH “å” () ARE
IMPORTANT FOR MAINTAINING THE SAFETY OF
THE SET. BE SURE TO REPLACE THESE PARTS
WITH SPECIFIED ONES FOR MAINTAINING THE
SAFETY AND PERFORMANCE OF THE SET.
AVIS DE SECURITE IMPORTANT:
LES PIECES MARQUEES “å” ( )SONT
IMPORTANTES POUR MAINTENIR LA SECURITE
DE L'APPAREIL.
NE REMPLACER CES PIEDES QUE PAR DES
PIECES DONT LE NUMERO EST SPECIFIE POUR
MAINTENIR LA SECURITE ET PROTEGER LE BON
FONCTIONNEMENT DE L'APPAREIL.
Replacement parts which have these special safety characteristics
identified in this manual; electrical components having such features
are identified by
and Schematic Diagrams. The use of a substitute replacement part
which dose no have the same safety characteristic as the factory
recommended replacement parts shown in this service manual may
create shock, fire or other hazards.
"HOW TO ORDER REPLACEMENT PARTS"
To have your order filled promptly and correctly, please fur nish the
following informations.
1. MODEL NUMBER2. REF. NO.
3. PART NO.4. DESCRIPTION
in USA: Contact your nearest SHARP Parts Distributor to order.
Les pi`eces de rechange qui pr élelesentent ces caract éleristiques
sp éleciales de s élecurit éle, sont identifi élees dans ce manuel : les
pi`eces élelectriques qui pr élesentent ces particularit éles, sont rep
éler élee par la marque å et sont hachur élees dans les listes de
pi`eces et dans les diagrammes sch élematiques.
La substitution d'une pi`ece de rechange par une autre qui ne pr
éLesente pas les m éoemes caract éLeristiques de s élecurit éle que
la pi`ece recommand élee parl'usine et dans ce manuel de service,
peut provoquer une éLelectrocution, un incendie ou toutautre sinistre.
"COMMENT COMMANDER LES PIECES DE RECHANGE"
Pour que votre commande soit rapidement et correctement remplie,
veuillez fournir les renseignements suivants.
1. NUMERO DU MODELE2. NO. DE REF
3. NO. DE PIECE4. DESCRIPTION
in CANADA: Contact SHARP Electronics of Conada Limited
R201VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R202VRS-CY1JF103FJ 10k 1/16W Metal Oxide AA
R203VRS-CY1JF102FJ 1.0k 1/16W Metal Oxide AA
R204VRS-CY1JF473FJ 47k 1/16W Metal Oxide AA
R205VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R206VRS-CY1JF103FJ 10k 1/16W Metal Oxide AA
R207VRS-CY1JF622FJ 6.2k 1/16W Metal Oxide AA
R208VRS-CY1JF473FJ 47k 1/16W Metal Oxide AA
R209VRS-CY1JF123FJ 12k 1/16W Metal Oxide AA
R210VRS-CY1JF242FJ 2.4k 1/16W Metal Oxide AA
R211VRS-CY1JF332FJ 3.3k 1/16W Metal Oxide AA
R212VRS-CY1JF332FJ 3.3k 1/16W Metal Oxide AA
R213VRS-CY1JF682FJ 6.8k 1/16W Metal Oxide AA
R214VRS-CY1JF122FJ 1.2k 1/16W Metal Oxide AA
R215VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R216VRS-CY1JF153JJ 15k 1/16W Metal Oxide AA
R217VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R218VRS-CY1JF391JJ 390 1/16W Metal Oxide AA
R219VRS-TV1JD103JJ 10k 1/16W Metal Oxide AA
R220VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R301VRS-CY1JF000JJ 01/16W Metal Oxide AA
R302VRS-TX2HF8R2JJ 8.2 1/2WMetal Oxide AA
R303VRS-CY1JF121JJ 120 1/16W Metal Oxide AA
R304VRS-CY1JF121JJ 120 1/16W Metal Oxide AA
R305VRS-TX2HF8R2JJ 8.2 1/2WMetal Oxide AA
R308VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R309VRS-TW2ED222JJ 2.2k 1/4WMetal Oxide AA
R310VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R311VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R312VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R314VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R315VRS-CY1JF122JJ 1.2k 1/16W Metal Oxide AA
R316VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R317VRS-CY1JF122JJ 1.2k 1/16W Metal Oxide AA
R324VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R326VRS-CA1JF000JJ 01/16W Metal Oxide AB
R327VRS-CY1JF000JJ 01/16W Metal Oxide AA
R328VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R329VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R333VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R335VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R337VRS-CY1JF000JJ 01/16W Metal Oxide AA
R338VRS-CY1JF000JJ 01/16W Metal Oxide AA
R401VRS-CY1JF000JJ 01/16W Metal Oxide AA
R402VRS-CY1JF000JJ 01/16W Metal Oxide AA
R403VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R404VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R405VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R406VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R407VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R408VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R409VRS-CY1JF000JJ 01/16W Metal Oxide AA
R410VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R411VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R412VRS-CY1JF000JJ 01/16W Metal Oxide AA
R413VRS-CY1JF000JJ 01/16W Metal Oxide AA
R414VRS-CY1JF000JJ 01/16W Metal Oxide AA
R415VRS-CY1JF000JJ 01/16W Metal Oxide AA
R419VRS-CY1JF000JJ 01/16W Metal Oxide AA
R420VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R430VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R434VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R435VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R436VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R437VRS-CY1JF000JJ 01/16W Metal Oxide AA
R454VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R456VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R459VRS-CY1JF000JJ 01/16W Metal Oxide AA
R460VRS-CY1JF000JJ 01/16W Metal Oxide AA
R701VRS-CY1JF1R0JJ 1.0 1/16W Metal Oxide AA
R702VRS-CY1JF154JJ 150k 1/16W Metal Oxide AA
R703VRS-CY1JF274JJ 270k 1/16W Metal Oxide AA
R704VRS-TQ2BD000JJ 01/8WMetal Oxide AA
R705VRS-TX2HF000JJ 01/2WMetal Oxide AA
R706VRS-CR3AD821JJ 820 1WMetal Oxide AC
R707VRS-CY1JF000JJ 01/16W Metal Oxide AA
R708VRS-CY1JF272FJ 2.7k 1/16W Metal Oxide AA
R709VRS-CY1JF123FJ 12k 1/16W Metal Oxide AA
R711VRS-CY1JF184JJ 180k 1/16W Metal Oxide AA
R712VRS-CY1JF683FJ 68k 1/16W Metal Oxide AA
R713VRS-CY1JF133FJ 13k 1/16W Metal Oxide AA
R715VRS-CY1JF000JJ 01/16W Metal Oxide AA
R716VRS-TX2HF000JJ 01/2WMetal Oxide AA
R717VRS-CY1JF152FJ 1.5k 1/16W Metal Oxide AA
R718VRS-CY1JF274JJ 270k 1/16W Metal Oxide AA
R719VRS-CY1JF563FJ 56k 1/16W Metal Oxide AA
R720VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R721VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R722VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R723VRS-CY1JF682JJ 6.8k 1/16W Metal Oxide AA
R725VRS-CY1JF1R0JJ 1.0 1/16W Metal Oxide AA
R726VRS-CY1JF1R0JJ 1.0 1/16W Metal Oxide AA
R729VRS-TQ2BD000JJ 01/8WMetal Oxide AA
R731VRS-TQ2BD000JJ 01/8WMetal Oxide AA
R732VRS-TW2ED222JJ 2.2k 1/4WMetal Oxide AA
R733VRS-TQ2BD683JJ 68k 1/8WMetal Oxide AA
R734VRS-CY1JF393JJ 39k 1/16W Metal Oxide AA
R735VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R736VRS-CY1JF1R0JJ 1.0 1/16W Metal Oxide AA
R737VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R738VRS-TW2ED102JJ 1.0k 1/4WMetal Oxide AA
R739VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R740VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R741VRS-CY1JF000JJ 01/16W Metal Oxide AA
R742VRS-CY1JF000JJ 01/16W Metal Oxide AA
R747VRS-CY1JF000JJ 01/16W Metal Oxide AA
R748VRS-CY1JF000JJ 01/16W Metal Oxide AA
R756VRS-CY1JF000JJ 01/16W Metal Oxide AA
R765VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R766VRS-CA1JF332JJ 3.3k 1/16W Metal Oxide AB
R767VRS-CB1JF332JJ 3.3k 1/16W Metal Oxide AC
R768VRS-CA1JF104JJ 100k 1/16W Metal Oxide AA
R769VRS-CB1JF104JJ 100k 1/16W Metal Oxide AA
R770VRS-CA1JF562JJ 5.6k 1/16W Metal Oxide AA
R771VRS-CB1JF562JJ 5.6k 1/16W Metal Oxide AC
R772VRS-CY1JF563JJ 56k 1/16W Metal Oxide AA
R774VRS-CY1JF000JJ 01/16W Metal Oxide AA
R801VRS-CB1JF221JJ 220 1/16W Metal Oxide AC
R802VRS-CB1JF220JJ 221/16W Metal Oxide AC
R803VRS-CB1JF220JJ 221/16W Metal Oxide AC
R804VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R806VRS-CY1JF221JJ 220 1/16W Metal Oxide AA
R807VRS-CY1JF000JJ 01/16W Metal Oxide AA
R808VRS-CY1JF000JJ 01/16W Metal Oxide AA
R809VRS-CY1JF000JJ 01/16W Metal Oxide AA
R810VRS-CB1JF220JJ 221/16W Metal Oxide AC
R811VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R812VRS-CY1JF000JJ 01/16W Metal Oxide AA
R813VRS-CB1JF220JJ 221/16W Metal Oxide AC
R814VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R815VRS-CY1JF000JJ 01/16W Metal Oxide AA
R816VRS-CA1JF470JJ 471/16W Metal Oxide AB
R819VRS-CY1JF000JJ 01/16W Metal Oxide AA
R826VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R831VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R832VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R833VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R834VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R852VRS-CY1JF000JJ 01/16W Metal Oxide AA
R860VRS-CY1JF000JJ 01/16W Metal Oxide AA
R861VRS-CY1JF000JJ 01/16W Metal Oxide AA
R901VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R902VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R903VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R905VRS-CY1JF000JJ 01/16W Metal Oxide AA
R909VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R910VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R913VRS-CY1JF000JJ 01/16W Metal Oxide AA
R914VRS-CY1JF000JJ 01/16W Metal Oxide AA
R915VRS-CY1JF000JJ 01/16W Metal Oxide AA
R916VRS-CY1JF000JJ 01/16W Metal Oxide AA
R917VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R918VRS-CY1JF822FJ 8.2k 1/16W Metal Oxide AA
R919VRS-CY1JF822FJ 8.2k 1/16W Metal Oxide AA
R920VRS-CY1JF822FJ 8.2k 1/16W Metal Oxide AA
R921VRS-CY1JF822FJ 8.2k 1/16W Metal Oxide AA
R922VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R923VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R924VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R925VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R951VRS-CY1JF000JJ 01/16W Metal Oxide AA
R954VRS-CY1JF000JJ 01/16W Metal Oxide AA
R958VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R959VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R960VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R961VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R962VRS-CY1JF153JJ 15k 1/16W Metal Oxide AA
R963VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R964VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R965VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R966VRS-CY1JF152JJ 1.5k 1/16W Metal Oxide AA
R967VRS-CY1JF152JJ 1.5k 1/16W Metal Oxide AA
R968VRS-CY1JF562JJ 5.6k 1/16W Metal Oxide AA
R969VRS-CY1JF562JJ 5.6k 1/16W Metal Oxide AA
R1101 VRS-CA1JF333JJ 33k 1/16W Metal Oxide AA
R1102 VRS-CA1JF103JJ 10k 1/16W Metal Oxide AA
R1103 VRS-CA1JF103JJ 10k 1/16W Metal Oxide AA
R1104 VRS-CA1JF333JJ 33k 1/16W Metal Oxide AA
R1105 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R1106 VRS-CA1JF333JJ 33k 1/16W Metal Oxide AA
R1107 VRS-CA1JF103JJ 10k 1/16W Metal Oxide AA
R1108 VRS-CA1JF103JJ 10k 1/16W Metal Oxide AA
R1109 VRS-CA1JF333JJ 33k 1/16W Metal Oxide AA
R1110 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R1111 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R1112 VRS-CY1JF103FJ 10k 1/16W Metal Oxide AA
R1113 VRS-CA1JF333JJ 33k 1/16W Metal Oxide AA
R1114 VRS-CY1JF103FJ 10k 1/16W Metal Oxide AA
R1115 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R1116 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R1117 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R1118 VRS-CY1JF823FJ 82k 1/16W Metal Oxide AA
R1119 VRS-CY1JF472FJ 4.7k 1/16W Metal Oxide AA
R1120 VRS-TW2ED1R5JJ 1.5 1/4WMetal Oxide AB
R1121 VRS-CY1JF391JJ 390 1/16W Metal Oxide AA
R1122 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R1123 VRS-CY1JF391JJ 390 1/16W Metal Oxide AA
R1124 VRS-CY1JF472FJ 4.7k 1/16W Metal Oxide AA
R1125 VRS-TW2ED101JJ 100 1/4WMetal Oxide AA
R1126 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1127 VRS-TX2HF3R9JJ 3.9 1/2WMetal Oxide AB
R1128 VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R1129 VRS-CY1JF563FJ 56k 1/16W Metal Oxide AA
R1130 VRS-TW2ED1R5JJ 1.5 1/4WMetal Oxide AB
R1131 VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R1132 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1133 VRS-CY1JF223FJ 22k 1/16W Metal Oxide AA
R1134 VRS-CY1JF822FJ 8.2k 1/16W Metal Oxide AA
R1135 VRS-CY1JF561JJ 560 1/16W Metal Oxide AA
R1136 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1137 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1138 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1202 VRS-CB1JF220JJ 221/16W Metal Oxide AC
R1203 VRS-CA1JF220JJ 221/16W Metal Oxide AA
R1204 VRS-CB1JF220JJ 221/16W Metal Oxide AC
R1205 VRS-CA1JF220JJ 221/16W Metal Oxide AA
R1206 VRS-CB1JF220JJ 221/16W Metal Oxide AC
R1207 VRS-CA1JF220JJ 221/16W Metal Oxide AA
R1208 VRS-CY1JF560JJ 561/16W Metal Oxide AA
R1209 VRS-CA1JF220JJ 221/16W Metal Oxide AA
R1210 VRS-CY1JF220JJ 221/16W Metal Oxide AA
R1211 VRS-CY1JF221JJ 220 1/16W Metal Oxide AA
R1212 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1214 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R1217 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R1218 VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R1220 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R1221 VRS-CB1JF332JJ 3.3k 1/16W Metal Oxide AC
R1222 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R1223 VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R1225 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R1226 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R1228 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1230 VRS-CY1JF562JJ 5.6k 1/16W Metal Oxide AA
R1231 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R1232 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R1233 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R1234 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R1235 VRS-CB1JF473JJ 47k 1/16W Metal Oxide AC
R1236 VRS-CB1JF473JJ 47k 1/16W Metal Oxide AC
R1242 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R2001 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R2002 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R2003 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2004 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2005 VRS-CY1JF106JJ 10M 1/16W Metal Oxide AA
R2006 VRS-CY1JF394JJ 390k 1/16W Metal Oxide AA
R2007 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2008 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2009 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R2010 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2011 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R2014 VRS-CA1JF103JJ 10k 1/16W Metal Oxide AA
R2016 VRS-CA1JF223JJ 22k 1/16W Metal Oxide AA
R2018 VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R2019 VRS-CB1JF331JJ 330 1/16W Metal Oxide AC
R2025 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R2028 VRS-CB1JF102JJ 1.0k 1/16W Metal Oxide AA
R2031 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2032 VRS-CY1JF471JJ 470 1/16W Metal Oxide AA
R2033 VRS-CY1JF105JJ 1.0M 1/16W Metal Oxide AA
R2035 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R2041 VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R2042 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2043 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R2044 VRS-CB1JF103JJ 10k 1/16W Metal Oxide AA
R2045 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2047 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2048 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R2049 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R2050 VRS-CY1JF562JJ 5.6k 1/16W Metal Oxide AA
R2051 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2052 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2053 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R2054 VRS-CY1JF333JJ 33k 1/16W Metal Oxide AA
R2055 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R2056 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2057 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R2058 VRS-CY1JF474JJ 470k 1/16W Metal Oxide AA
R2059 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2060 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R2061 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R2062 VRS-CY1JF333JJ 33k 1/16W Metal Oxide AA
R2063 VRS-CY1JF333JJ 33k 1/16W Metal Oxide AA
R2067 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2068 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R2069 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R2074 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R2075 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R2076 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R2078 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7000 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R7003 VRS-CY1JF471JJ 470 1/16W Metal Oxide AA
R7004 VRS-CY1JF471JJ 470 1/16W Metal Oxide AA
R7009 VRS-CY1JF182JJ 1.8k 1/16W Metal Oxide AA
R7010 VRS-CY1JF182JJ 1.8k 1/16W Metal Oxide AA
R7020 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R7021 VRS-CY1JF471JJ 470 1/16W Metal Oxide AA
R7022 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7023 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7024 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R7025 VRS-CY1JF224JJ 220k 1/16W Metal Oxide AA
R7026 VRS-CY1JF221JJ 220 1/16W Metal Oxide AA
R7027 VRS-CY1JF561JJ 560 1/16W Metal Oxide AA
R7028 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7029 VRS-CY1JF391JJ 390 1/16W Metal Oxide AA
R7030 VRS-CY1JF561JJ 560 1/16W Metal Oxide AA
R7031 VRS-CY1JF561JJ 560 1/16W Metal Oxide AA
R7032 VRS-CY1JF911JJ 910 1/16W Metal Oxide AA
R7033 VRS-CY1JF561JJ 560 1/16W Metal Oxide AA
R7034 VRS-CY1JF911JJ 910 1/16W Metal Oxide AA
R7036 VRS-CY1JF132JJ 1.3k 1/16W Metal Oxide AA
R7037 VRS-CY1JF682JJ 6.8k 1/16W Metal Oxide AA
R7038 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7039 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7040 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7041 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7042 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7043 VRS-CB1JF101JJ 100 1/16W Metal Oxide AA
R7044 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R7045 VRS-CY1JF122JJ 1.2k 1/16W Metal Oxide AA
R7046 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7047 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7048 VRS-CY1JF100JJ 101/16W Metal Oxide AA
R7049 VRS-CY1JF471JJ 470 1/16W Metal Oxide AA
R7050 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R7051 VRS-CY1JF911JJ 910 1/16W Metal Oxide AA
R7052 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7053 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R7054 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7055 VRS-CY1JF152JJ 1.5k 1/16W Metal Oxide AA
R7056 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7058 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R7059 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7060 VRS-CY1JF911JJ 910 1/16W Metal Oxide AA
R7062 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7066 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7067 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7068 VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R7069 VRS-CY1JF473JJ 47k 1/16W Metal Oxide AA
R7071 VRS-CY1JF182JJ 1.8k 1/16W Metal Oxide AA
R7072 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7078 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7079 VRS-CY1JF333JJ 33k 1/16W Metal Oxide AA
R7080 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7081 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7084 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7085 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7108 VRS-TX2HF000JJ 01/2WMetal Oxide AA
R7109 VRS-TX2HF000JJ 01/2WMetal Oxide AA
R7110 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R7111 VRS-TX2HF2R2JJ 2.2 1/2WMetal Oxide AB
R7112 VRS-TX2HF2R2JJ 2.2 1/2WMetal Oxide AB
R7309 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R7313 VRS-TX2HF000JJ 01/2WMetal Oxide AA
R7314 VRS-TX2HF000JJ 01/2WMetal Oxide AA
R7330 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R7331 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7332 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R7333 VRS-CY1JF222JJ 2.2k 1/16W Metal Oxide AA
R7334 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7335 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R7337 VRS-TX2HF8R2JJ 8.2 1/2WMetal Oxide AA
R7338 VRS-TX2HF8R2JJ 8.2 1/2WMetal Oxide AA
R7371 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7379 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R7384 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R7385 VRS-CR3AD391JJ 390 1WMetal Oxide AC
R3201 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3202 VRS-CA1JF101JJ 100 1/16W Metal Oxide AA
R3203 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3204 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3205 VRS-CY1JF153JJ 15k 1/16W Metal Oxide AA
R3206 VRS-CY1JF332JJ 3.3k 1/16W Metal Oxide AA
R3207 VRS-CY1JF152JJ 1.5k 1/16W Metal Oxide AA
R3208 VRS-CY1JF331JJ 330 1/16W Metal Oxide AA
R3209 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3301 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3302 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3303 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3304 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3305 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3306 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3308 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R3310 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R3313 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R3314 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3315 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R3319 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3321 VRS-CY1JF822JJ 8.2k 1/16W Metal Oxide AA
R3323 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3324 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3401 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3402 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3404 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3409 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3410 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3411 VRS-CY1JF680JJ 681/16W Metal Oxide AA
R3412 VRS-CY1JF680JJ 681/16W Metal Oxide AA
R3413 VRS-CY1JF223JJ 22k 1/16W Metal Oxide AA
R3414 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3415 VRS-CY1JF562JJ 5.6k 1/16W Metal Oxide AA
R3416 VRS-CY1JF272JJ 2.7k 1/16W Metal Oxide AA
R3420 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3421 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3422 VRS-TQ2BD750JJ 751/8WMetal Oxide AA
R3423 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3424 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3425 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R3426 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3427 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3428 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R3429 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R3431 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3432 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3435 VRS-CY1JF103JJ 10k 1/16W Metal Oxide AA
R3461 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3462 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
R3463 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3464 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
R3465 VRS-TV1JD1R0JJ 1.0 1/16W Metal Oxide AA
R3466 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R3467 VRS-TW2ED102JJ 1.0k 1/4WMetal Oxide AA
R3469 VRS-CY1JF000JJ 01/16W Metal Oxide AA
R3470 VRS-CY1JF102JJ 1.0k 1/16W Metal Oxide AA
å T7751 RTRNZ0776CEZZJ TransformerAM
å T7752 RTRNZ0776CEZZJ TransformerAM
å T7753 RTRNZ0776CEZZJ TransformerAM
å T7754 RTRNZ0776CEZZJ TransformerAM
å T7755 RTRNZ0776CEZZJ TransformerAM
å T7756 RTRNZ0776CEZZJ TransformerAM
R7751 VRS-TW2ED332JJ 3.3k 1/4WMetal Oxide AB
R7752 VRS-TW2ED332JJ 3.3k 1/4WMetal Oxide AB
R7753 VRS-TW2ED332JJ 3.3k 1/4WMetal Oxide AB
R7754 VRS-TW2ED332JJ 3.3k 1/4WMetal Oxide AB
R7755 VRS-CY1JF822JJ 8.2k 1/16W Metal Oxide AA
R7756 VRS-CY1JF333JJ 33k 1/16W Metal Oxide AA
R4005 VRS-CY1JF123JJ 12k 1/16W Metal Oxide AA
R4006 VRS-CY1JF822JJ 8.2k 1/16W Metal Oxide AA
R4011 VRS-CY1JF123JJ 12k 1/16W Metal Oxide AA
R4012 VRS-CY1JF822JJ 8.2k 1/16W Metal Oxide AA
R4013 VRS-TX2HF331JJ 330 1/2WMetal Oxide AB
R4014 VRS-CY1JF392JJ 3.9k 1/16W Metal Oxide AA
R4015 VRS-TX2HF331JJ 330 1/2WMetal Oxide AB
R4016 VRS-CY1JF392JJ 3.9k 1/16W Metal Oxide AA
R4020 VRS-CY1JF182JJ 1.8k 1/16W Metal Oxide AA
R4021 VRS-CY1JF101JJ 100 1/16W Metal Oxide AA
R4022 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R4023 VRS-CY1JF183JJ 18k 1/16W Metal Oxide AA
R4024 VRS-CY1JF183JJ 18k 1/16W Metal Oxide AA
R4025 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R4026 VRS-CY1JF472JJ 4.7k 1/16W Metal Oxide AA
R4027 VRS-CY1JF820JJ 821/16W Metal Oxide AA
R4028 VRS-CY1JF331JJ 330 1/16W Metal Oxide AA
R4029 VRS-CY1JF104JJ 100k 1/16W Metal Oxide AA
SWITCHES
S4701 QSW-P0614CEZZJ Main PowerAF
SW4002
SW4003
SW4004
SW4006
SW4007
SW4008
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
D Japan P Japan TQ0998-S
Oct. 2000 Printed in Japan
NA. KG
SHARP CORPORATION
A V Systems Group
Quality & Reliability Control Center
Yaita, Tochigi 329-2193, Japan
48
Loading...
+ hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.