Sharp LC-19LS410UT, LC-32LS510UT, LC-22LS510UT User Manual

Download

SHARP ELECTRONICS CORPORATION

Sharp Plaza, Mahwah, New Jersey 07495-1163

SHARP CORPORATION

LC-19LS410UT LC-22LS510UT LC-32LS510UT

LIQUID CRYSTAL TELEVISION TÉLÉVISEUR ACL TELEVISOR CON PANTALLA

DE CRISTAL LÍQUIDO

OPERATION MANUAL MODE D'EMPLOI MANUAL DE OPERACIÓN

ENGLISH

FRANÇAIS

ESPAÑOL

Printed in China Imprimé au Chine Impreso en China Z41G320184303C

LC-19LS410UT

LC-22LS510UT / LC-32LS510UT

IMPORTANT : Please read this operation manual before starting operating the equipment. IMPORTANT : Veuillez lire ce mode d’emploi avant de commencer à utilliser l’appareil. IMPORTANTE : Lea este manual de operación antes de comenzar a operar el equipo.

LC-19LS410UT LC-22LS510UT LC-32LS510UT

OPERATION MANUAL

IMPORTANT: To aid reporting in case of loss or theft, please record the TV's model and serial numbers in the space provided. The numbers are located at the rear of the TV.

Model No.:

Serial No.:

LIQUID CRYSTAL TELEVISION

ENGLISH

IMPORTANT INFORMATION

ENGLISH

WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,

DO NOT REMOVE COVER (OR BACK).

NO USER-SERVICEABLE PARTS INSIDE.

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This “bolt of lighting” indicates uninsulated material within your unit may cause an electric shock. For the safety of everyone in your household, please do not remove product covering.

The “exclamation point” calls attention to features for which you should read the enclosed literature closely to prevent operating and maintenance problems.

IMPORTANT INFORMATION

TRADEMARKS

WARNING:

FCC Regulations state that any unauthorized changes or modiﬁcations to this

equipment not expressly approved by the manufacturer could void the user’s authority to operate this equipment.

CAUTION:

This product satisﬁes FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections.

DECLARATION OF CONFORMITY:

SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-19LS410UT / LC-22LS510UT / LC-32LS510UT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

RESPONSIBLE PARTY:

SHARP ELECTRONICS CORPORATION Sharp Plaza, Mahwah, New Jersey 07495-1163 TEL: 1-800-BE-SHARP

For Business Customers: URL http://www.sharpusa.com

INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

— Reorient or relocate the receiving antenna. — Increase the separation between the equipment and receiver. — Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

— Consult the dealer or an experienced radio/TV technician for help.

Note to CATV system installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electrical Code that provides guidelines for proper grounding and, in particular, speciﬁes that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

HDMI, the HDMI logo and High-Deﬁnition Multimedia Interface are trademarks • or registered trademarks of HDMI Licensing LLC in the United States and other countries.

Manufactured under license from Dolby Laboratories. Dolby and the double-D • symbol are trademarks of Dolby Laboratories.

Products that have earned the ENERGY STAR® are designed to protect the • environment through superior energy efﬁciency.

Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years of trouble-free operation of your product, please read the Important Safety Instructions carefully before using this product.

DEAR SHARP CUSTOMER

IMPORTANT SAFETY INSTRUCTIONS

Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage if improperly handled. This product has been engineered and manufactured with the highest priority on safety. However, improper use can result in electric shock and/or ﬁre. In order to prevent potential danger, please observe the following instructions when installing, operating and cleaning the product. To ensure your safety and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully before using the product.

1) Read these instructions.

2) Keep these instructions.

3) Heed all warnings.

4) Follow all instructions..

5) Do not use this apparatus near water.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliﬁers) that produce heat.

9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not ﬁt into your outlet, consult an electrician for replacement of the obsolete outlet.

10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11) Only use attachments/accessories speciﬁed by the manufacturer.

12) Use only with the cart, stand, tripod, bracket, or table speciﬁed by the

manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13) Unplug this apparatus during lightning storms or when unused for long periods of

time.

14) Refer all servicing to qualiﬁed service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Additional Safety Information

15) Power Sources—This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of ﬁre or electric shock.

17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a ﬁre or electric shock. Never spill liquid of any kind on the product.

IMPORTANT SAFETY INSTRUCTIONS

18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualiﬁed service personnel under the following conditions:

a) When the AC cord or plug is damaged, b) If liquid has been spilled, or objects have fallen into the product, c) If the product has been exposed to rain or water, d) If the product does not operate normally by following the operating instructions.

Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a

qualiﬁed technician to restore the product to its normal operation, e) If the product has been dropped or damaged in any way, and f) When the product exhibits a distinct change in performance - this indicates a need for service.

19) Replacement Parts—When replacement parts are required, be sure the service technician has

used replacement parts speciﬁed by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in ﬁre, electric shock, or other hazards.

20) Safety Check—Upon completion of any service or repairs to this product, ask the service

technician to perform safety checks to determine that the product is in proper operating condition.

21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the

product according to the method recommended by the manufacturer.

These servicing instructions are for use by qualiﬁed service personnel only. To reduce •

the risk of electric shock do not perform any servicing other than that contained in the operating instructions unless you are qualiﬁed to do so.

Outdoor Antenna Grounding — If an outside •

antenna is connected to the television equipment, be sure the antenna system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

EXAMPLE OF ANTENNA GROUNDING AS PER NATIONAL ELECTRICAL CODE, ANSI/NFPA 70

ANTENNA LEAD IN WIRE

GROUND CLAMP

NEC — NATIONAL ELECTRICAL CODE

GROUNDING CONDUCTORS (NEC SECTION 810-21)

GROUND CLAMPS

POWER SERVICE GROUNDING ELECTRODE SYSTEM (NEC ART 250, PART H)

ELECTRIC SERVICE EQUIPMENT

ANTENNA DISCHARGE UNIT (NEC SECTION 810-20)

CAUTION

Warning statement indicating that Class I apparatus shall be connected to a mains socket •

outlet with a protective earthing connection.

Statement indicating that when the mains plug or appliance coupler shall remain readily •

operable.

Where the MAINS plug or an appliance coupler is used as the disconnect device, the •

disconnect device shall remain readily operable.

Where an all-pole MAINS SWITCH is used as the disconnect device, the location on the •

apparatus and the function of the switch shall be described, and the switch shall remain readily operable.

IMPORTANT SAFETY INSTRUCTIONS

Water and Moisture — Do not use this product near water - for example, near a bath tub, wash •

bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like.

Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the •

product on an unstable base can cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall, be sure to follow the manufacturer’s instructions. Use only the mounting hardware recommended by the manufacturer.

Selecting the location — Select a place with no direct sunlight and good ventilation.• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not •

cover or block these vents and openings since insufﬁcient ventilation can cause overheating and/or shorten the life of the product. Do not place the product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation is provided or the manufacturer’s instructions are followed.

The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the •

product is dropped or applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.

Heat — The product should be situated away from heat sources such as radiators, heat •

registers, stoves, or other products (including ampliﬁers) that produce heat.

The Liquid Crystal panel is a very high technology product with 1,049,088 pixels (LC-19LS410UT) •

/ 2,073,600 pixels (LC-22LS510UT/LC-32LS510UT), giving you ﬁne picture details. Occasionally, a few non-active pixels may appear on the screen as a ﬁxed point of blue, green or red. Please note that this does not affect the performance of your product.

Lightning — For added protection for this television equipment during a lightning storm, or •

when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the equipment due to lightning and powerline surges.

Power Lines — An outside antenna system should not be located in the vicinity of overhead •

power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

To prevent ﬁre, never place any type of candle or ﬂames on the top or near the TV set.• To prevent ﬁre or shock hazard, do not place the AC cord under the TV set or other heavy •

items.

To prevent ﬁre or shock hazard, do not expose this product to dripping or •

splashing. No objects ﬁlled with liquids, such as vases, should be placed on the product.

Do not insert foreign objects into the product. Inserting objects in the air •

vents or other openings may result in ﬁre or electric shock. Exercise special caution when using the product around children.

Precautions when transporting the TV

When transporting the TV, never carry it by holding or otherwise putting pressure onto the •

display. Be sure to always carry the TV by two people holding it with two hands — one hand on each side of the TV.

Do not display a still picture for a long time, as this could cause an afterimage to remain.•

IMPORTANT SAFETY INSTRUCTIONS

Caring for the Cabinet

Use a soft cloth (cotton, ﬂannel, etc.) and gently wipe the surface of the cabinet.• Using a chemical cloth (wet/dry sheet type cloth, etc.) may deform the components of the main •

unit cabinet or cause cracking.

Wiping with a hard cloth or using strong force may scratch the surface of the cabinet.• If the cabinet is very dirty, wipe with a soft cloth (cotton, ﬂannel, etc.) soaked in neutral •

detergent diluted with water and thoroughly wrung out, and then wipe with a soft dry cloth.

The cabinet is primarily made of plastic. Avoid using benzene, thinner, and other solvents, as •

these may deform the cabinet and cause the paint to peel off.

Do not apply insecticides or other volatile liquids. •

Also, do not allow the cabinet to remain in contact with rubber or vinyl products for a long period of time. Plasticizers inside the plastic may cause the cabinet to deform and cause the paint to peel off.

Caring for the Liquid Crystal panel

Turn off the main power and unplug the AC cord from the wall outlet before handling.• Gently wipe the surface of the display panel with a soft cloth (cotton, ﬂannel, etc.). •

To protect the display panel, do not use a dirty cloth, liquid cleaners, or a chemical cloth (wet/ dry sheet type cloth, etc.). This may damage the surface of the display panel.

Wiping with a hard cloth or using strong force may scratch the surface •

of the display panel.

Use a soft damp cloth to gently wipe the display panel when it is really •

dirty. (It may scratch the surface of the display panel when wiped strongly.)

If the display panel is dusty, use an anti-static brush, which is commercially available, to clean it.• To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved •

cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCDCLOTH-3) packs. Call 1-800-BE-SHARP for ordering, or VISIT http://www.sharpusa.com/SharpDirect.

IMPORTANT SAFETY INSTRUCTIONS

CHILD SAFETY

It Makes A Difference How and Where You Use Your Flat Panel Display

Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:

THE ISSUE

The home theater entertainment experience is a growing trend and larger • ﬂat panel displays are popular purchases. However, ﬂat panel displays are not always supported on the proper stands or installed according to the manufacturer’s recommendations.

Flat panel displays that are inappropriately situated on dressers, bookcases, • shelves, desks, speakers, chests or carts may fall over and cause injury.

THIS MANUFACTURER CARES!

The consumer electronics industry is committed to making home • entertainment enjoyable and safe.

TUNE INTO SAFETY

One size does NOT ﬁt all. Follow the manufacturer’s recommendations for • the safe installation and use of your ﬂat panel display.

Carefully read and understand all enclosed instructions for proper use of this • product.

Don’t allow children to climb on or play with furniture and television sets.• Don’t place ﬂat panel displays on furniture that can easily be used as steps, •

such as a chest of drawers. Remember that children can become excited while watching a program, •

especially on a “larger than life” ﬂat panel display. Care should be taken to place or install the display where it cannot be pushed, pulled over, or knocked down.

Care should be taken to route all cords and cables connected to the ﬂat • panel display so that they cannot be pulled or grabbed by curious children.

WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT PANEL DISPLAY, ALWAYS:

Use a mount that has been recommended by the display manufacturer and/or listed by an • independent laboratory (such as UL, CSA, ETL).

Follow all instructions supplied by the display and wall mount manufacturers.• If you have any doubts about your ability to safely install your ﬂat panel display, contact your retailer •

about professional installation. Make sure that the wall where you are mounting the display is appropriate. Some wall mounts are not •

designed to be mounted to walls with steel studs or old cinder block construction. If you are unsure, contact a professional installer.

A minimum of two people are required for installation. Flat panel displays can be heavy.•

Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S. consumer electronics industry. More than 2,200 companies enjoy the beneﬁts of CEA membership, including legislative advocacy, market research, technical training and education, industry promotion and the fostering of business and strategic relationships.

QUICK REFERENCE

Supplied Accessories

Always use the AC cord supplied with the TV.• The illustrations above are for explanation purposes and may vary slightly from the •

actual accessories.

Make sure the following accessories are provided with the product.

Remote control unit

(g1)

Page 11

“AA” size battery

(g2)

Page 13

AC cord

(g1)

Page 10

x 3 x 4

19”

22”

32”

Stand (g1) with Screws

Page 8

Operation manual

(g1)

Attaching/Detaching the Stand

Before attaching (or detaching) the stand, unplug the AC cord from the AC INPUT • terminal.

Before performing work spread cushioning over the base area to lay the TV on. This will • prevent it from being damaged.

CAUTION

Attach the stand in the correct direction.• Be sure to follow the instructions. Incorrect installation of the stand may result •

in the TV falling over.

Put the TV face down on a safe surface that is covered by a soft and smooth cloth.1. Adjust the TV stand to the bottom of the TV.2. Fasten the screws by using a cross-head screwdriver (Not supplied).3.

CAUTION

Do not push to hard or put excessive pressure • to the stand neck to avoid the damages when you turn the TV for the most comfortable viewing angle.

32”

19”

22”

To detach the stand, perform the steps in reverse • order.

QUICK REFERENCE

Detaching the stand neck for wall mounting

CAUTION

Please use care when disassembling cabinet, stand, and pillar for wall • mounting.

Detach the stand neck in the correct direction.• Do not remove the stand neck from the TV unless using an optional wall mount •

bracket to mount it.

Loosen the 4 screws that secure the stand neck by using a cross-head screwdriver. 1. Remove stand cover from the TV set.

To attach the stand neck, perform the steps in reverse order.• Do not force or overtighten and do not install without stand covers.•

Stand Cover

These 2 screws need to be installed in the right holes. Do not force or overtighten and do not install without stand covers. Failure to follow this procedure will cause damage to the cabinet.

AA&B

19” / 22” 32”

A B

Quick Installation Tips

Attach your antenna to the back of the television. (See page 12.)

How to turn on the television for the ﬁrst time.

A) Press POWER on the television. B) The POWER indicator on the front

of the television lights BLUE.

Connect the AC plug for the television into the AC outlet.

Speakers cannot be detached from the • TV.

Place the TV close to the AC outlet, and • keep the power plug within reach.

This product must only be connected to • a 120V, 60Hz. Connecting it to any other kind of outlet will damage the product and invalidate the warranty.

TO PREVENT RISK OF ELECTRIC • SHOCK, DO NOT TOUCH UNINSULATED PARTS OF ANY CABLES WITH THE AC CORD CONNECTED.

AC outlet

POWER

POWER indicator

QUICK REFERENCE

Using the Remote Control Unit

Use the remote control unit by pointing it towards the remote control sensor on the TV. Objects between the remote control unit and the remote control sensor may prevent proper operation.

30º (5m) Horizontal & Vertical

(7 m)

Remote control sensor

■

Cautions regarding the remote control unit

Do not expose the remote control unit • to shock. In addition, do not expose the remote control unit to liquids, and do not place in an area with high humidity.

Do not install or place the remote control • unit under direct sunlight. The heat may cause deformation of the remote control unit.

The remote control unit may not work • properly if the remote control sensor on the TV is under direct sunlight or strong lighting. In such cases, change the angle of the lighting or the TV, or operate the remote control unit closer to the remote control sensor.

IMPORTANT:

If the POWER indicator on the television still does not light up, press POWER on the remote control to turn the power on.

IMPORTANT:

IF THE UNIT DOES NOT POWER ON - UNPLUG THE TELEVISION FROM THE OUTLET AND REPEAT THE INSTALLATION STEPS.

IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT US AT 1-800-BE-SHARP.

QUICK REFERENCE

Antennas

To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector, plug it into the antenna terminal at the rear of the TV set.

A 75-ohm system is generally a round 1. cable with F-type connector that can easily be attached to a terminal without tools (Commercially available).

A 300-ohm system is a ﬂat “twin-lead” 2. cable that can be attached to a 75-ohm terminal through a 300/75-ohm adapter (Commercially available).

When connecting the RF cable to the TV set, do not tighten F-type connector with tools. If tools are used, it may cause damage to your TV set. (The breaking of internal circuit, etc.)

Preparation

Connecting Antenna Cable

Connect the antenna cable to the TV using one of the methods in the illustration as • shown (1, 2, 3 or 4).

F-type connector

300-ohm twin-lead cable (ﬂat)

F-type connector

75-ohm coaxial cable (round)

75-ohm coaxial cable

300-ohm twin-lead cable

75-ohm coaxial cable (round)

75-ohm coaxial cable

IN OUT

300-ohm twin-lead cable

VHF ANTENNA

UHF ANTENNA

Combiner (commercially available)

300/75-ohm adapter

(commercially available)

300-ohm twin-lead cable (ﬂat)

75-ohm coaxial cable (round)

Cable TV lead-In

Cable without a CATV converter1

Coaxial cable (commercially available)

Home Antenna terminal (75-ohm)

VHF/UHF antenna2

Combination VHF/UHF antenna3

Separate VHF/UHF antenna4

To TV antenna terminal

Installing Batteries in the Remote Control Unit

CAUTION

Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.

Do not mix batteries of different types. Different types of batteries have different • characteristics.

Do not mix old and new batteries. Mixing old and new batteries can shorten the life of • new batteries or cause chemical leakage in old batteries.

Remove batteries as soon as they are worn out. Chemicals that leak from batteries • come in contact with skin can cause a rash. If you ﬁnd any chemical leakage, wipe thoroughly with a cloth.

The batteries supplied with this product may have a shorter life expectancy due to • storage conditions.

If you will not be using the remote control unit for an extended period of time, remove • batteries from it.

The batteries (batteries installed) shall not be exposed to excessive heat such as • sunshine, ﬁre or the like.

1 Open the battery cover.

Place the batteries with their terminals • corresponding to the (e) and (f) indications in the battery compartment.

2 Insert two “AA” size batteries (supplied

with the product).

3 Close the battery cover.

If the remote control fails to operate TV functions, replace the batteries in the remote control unit.

Preparation

Contents

Dimensional Drawings

The dimensional drawings for the LCD TV set are shown on the inside back cover.•

IMPORTANT INFORMATION ...................................................................................... 1

TRADEMARKS ............................................................................................................. 2

IMPORTANT SAFETY INSTRUCTIONS ...................................................................... 3

QUICK REFERENCE .................................................................................................... 8

Supplied Accessories .............................................................................................. 8

Attaching/Detaching the Stand ................................................................................ 8

Detaching the stand neck for wall mounting ............................................................. 9

Quick Installation Tips ............................................................................................ 10

Using the Remote Control Unit .............................................................................. 11

Antennas ............................................................................................................... 12

Connecting Antenna Cable .................................................................................... 12

Installing Batteries in the Remote Control Unit ........................................................ 13

Contents ..................................................................................................................... 14

Part Names ................................................................................................................ 15

TV (Front) ............................................................................................................... 15

TV (Side/Rear) ........................................................................................................ 15

Remote Control Unit .............................................................................................. 16

Connecting to External Equipment .......................................................................... 17

Watching TV ............................................................................................................... 19

Turning On/Off the Power ...................................................................................... 19

Initial Setup ............................................................................................................ 19

Direct Button Operation ............................................................................................ 21

On-Screen Display Menu .......................................................................................... 25

Menu Items ............................................................................................................ 25

On-Screen Display Menu Operation ....................................................................... 27

Menu Operation Button ......................................................................................... 28

Video Menu ........................................................................................................... 28

Audio Menu ........................................................................................................... 30

TV Menu ................................................................................................................ 31

Setup Menu ........................................................................................................... 32

Parental Menu ....................................................................................................... 34

USB Menu ............................................................................................................. 38

Appendix .................................................................................................................... 40

Troubleshooting ..................................................................................................... 40

Speciﬁcations ........................................................................................................ 41

PC Compatibility Chart .......................................................................................... 42

RS232 Port Speciﬁcations ..................................................................................... 43

Information on the Software License for This Product ............................................ 44

Legal notices ......................................................................................................... 45

Calling for Service ..................................................................................................... 46

LIMITED WARRANTY ................................................................................................ 46

Remote control sensor

POWER indicator (See page 19.)

Part Names

TV (Front)

TV (Side/Rear)

INPUT 1 (AV IN)

USB

Earphone Output

INPUT 1 (AV IN)

USB

INPUT 8 (HDMI)

Earphone Output

AC IN

Power conntector

22”

19”

32”

INPUT 4, 5 (HDMI)

Antenna/Cable in

RS-232C IOIOI

INPUT 2

(COMPONENT)

AUDIO OUT

INPUT 3 (PC IN)

INPUT 5, 6, 7 (HDMI)

Antenna/Cable in

RS-232C IOIOI

INPUT 2, 3 (COMPONENT)

AUDIO OUT

INPUT 4 (PC IN)

Volume buttons (VOL +/- )

MENU button

INPUT button

POWER button

Channel buttons (CH / )

*1: See pages 12, 17, and 18 for external equipment connection. *2: See page 19 and 28 for button operations. *3: See page 10 for connecting the AC cord.

The illustrations in this operation manual are for explanation purposes and may vary slightly from • the actual operations.

The examples used throughout this manual are based on the LC-22LS510UT model.•

Remote Control Unit

Part Names

POWER: 1 Switch the power on or enters

standby mode. (See page 19.) 0–9: 2 Set the channel.

• (DOT): 3 (See page 21.) SURROUND: 4 Display the surround setting

menu. (See page 22.) FREEZE: 5 Set the still image. Press again to

return to normal screen.

When using the remote control unit, • point it at the TV.

SLEEP: 6 Allows you to set a time when the TV automatically switches to standby. This display will disappear after a few seconds, and the sleep timer automatically starts counting down. (See page 21.)

If you want to adjust the sleep timer • again, you can press this button repeatedly then change the time setting.

The TV will enter the standby mode • when the remaining time reaches zero.

EXIT: 7 Turn off the menu screen. CC: 8 Display captions during closed-caption

source. (See page 23.) AUDIO: 9 Display the MTS/SAP setting

menu. (See page 22-23.)

FAVORITE CH:10 A, B, C, D: Select 4 preset favorite channels in 4 different categories. (See page 31 for details.) While watching, you can toggle the selected channels by pressing A, B, C and D.

DISPLAY: 11 Display the current channel (or input source) information on the screen.

INPUT: 12 Select a TV input source. (See page 21.)

MUTE: 13 Mute the sound. (See page 21.)

VOL 14

k/l

: Set the volume. (See page 21.)

CH15

r/s

: Select the channel.

(See page 21.) ENT: 16 Jumps to a channel after selecting

with the 0–9 buttons. FLASHBACK: 17 Press to switch to the

previously tuned channel. Press again to switch back to the currently tuned channel.

MENU: 18 Display the menu screen.

/b/c/dENTER: Select a desired item

on the screen. RETURN: 20 Return to the previous menu

screen. VIEW MODE: 21 Select the Picture Mode.

(See page 24.)

AV MODE:22 Select an adjusted picture settings. (Standard, Movie, Power Saver, User, Sports) (See page 22.)

Connecting to External Equipment

You can connect many types of external equipment to your TV like a Blu-ray disc player, HD-DVD player, DVD player, VCR, HDMI equipment, game console or camcorder. To view external source images, select the input source from INPUT on the remote control unit or INPUT on the TV. (See page 21.)

CAUTION

To protect equipment, always turn off the TV before connecting any external •

equipment.

Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before •

making connections.

Connecting a Blu-ray disc player, HD-DVD player, DVD player, VCR, game console or camcorder.

Terminal on the TV

Cable

Terminal on external

equipment

INPUT 1 (AV IN)

INPUT 2 (COMPONENT)

INPUT 4, 5

AUDIO OUT

AV cable (commercially available)

Component video cable (commercially available)

Audio cable (commercially available)

HDMI-certified cable (commercially available)

Audio cable (commercially available)

Headphone cable (commercially available)

HEADPHONE OUTPUT

INPUT 2, 3 (COMPONENT)

22”

19”

32”

22”

19”

INPUT 5, 6, 7 ,8

32”

•

When using an HDMI-DVI conversion cable, input the audio signal to AUDIO terminal of PC IN.

•

To enjoy the 1080p display capability, connect your Blu-ray disc player, HD-DVD player or other external equipment using an HDMI-certiﬁed cable and set the equipment to 1080p output.

Connecting to External Equipment

Terminal on the TV

Cable

Terminal on PC

INPUT 3 (PC IN)

Connecting a PC

RGB cable (commercially available)

ø 3.5 mm stereo minijack cable (commercially available)

HDMI-certified cable (commercially available)

22”

19”

32”

INPUT 4 (PC IN)

INPUT 4, 5

22”

19”

INPUT 5, 6, 7 ,8

32”

The HDMI terminals only support digital signal.• Refer to page 42 for a list of PC signals compatible with the TV.•

Turning On/Off the Power

Initial Setup

POWER

Watching TV

When you turn on the TV for the ﬁrst time, the Initial Setup will guide you through the setup process. Perform the following steps before you press POWER on the remote control unit.

Insert the batteries into the remote 1. control unit. (See page 13.)

Connect the antenna cable to the TV. 2

(See page 12.) Plug in the AC cord to the AC outlet. 3

(See page 10.)

Initial Setup1.

The Initial Setup screen display at •

the ﬁrst use. Press ENTER to start the initial setup.

Welcome to use the Wizard for

Initial Setup !!

Please press [ENTER] to start the

wizard.

Initial Setup Welcome

Language setting2.

Select the OSD menu language •

from English, Spanish, or French.

Press •

/b to select the desired

language listed on the screen, and then press the d button to the next step.

Please select your language:

Initial Setup Language

English

Français

Español

Exit

EXIT

Back Select Next

Press POWER on the TV, or POWER on the remote control unit to turn the power on.

POWER indicator (Blue): The TV is on. •

Press POWER on the TV, or POWER on the remote control unit again to turn the power off.

The TV enters standby and the image on the screen • disappears.

• IfyouarenotgoingtousethisTVforalongperiodoftime,

be sure to remove the AC cord from the AC outlet.

• Smallamountofelectricpowerisstillconsumedevenwhen

the TV is turned off.

• Ifthereisnosignalinputfor15minutes,thepowerwillturnto

standby mode automatically.

Watching TV

3. Location setting

Press •

/b to select “Home” or

“Store” and press d to the next step.

Please select your location:

Home mode is destined for home

user.

Store mode is designed for retail

store.

Initial Setup Location

Home

Store

Exit

EXIT

Back Select Next

4. Time Zone setting

Press •

/b to select your current

location for time zone.

Please select your time zone:

Initial Setup Time Zone

Eastem Time

Central Time

Indiana

Mountain Time

Pacific Time

Arizona

Hawaii

Alaska

Exit

EXIT

Back Select Next

5. Tuner setting

Make sure what kind of connection •

is made with your TV when selecting “Air” or “Cable”.

Press •

/b to select “Air” or

“Cable” and press d to the next step.

Please select your tuner mode:

Initial Setup Tuner

Air

Cable

Exit

EXIT

Back Select Next

6. Channel scan setting

Press •

/b to select “Scan”

or “Skip Scan” and press d to continue.

First, please connect cable and/or

antenna.

Start channel scan now ?

If you skip this step, the channel

scan could be performed in Menu.

Initial Setup Channel Scan

Scan

Skip Scan

Exit

EXIT

Back Select Next

7. Start channel searching

Wait until the channel scan to •

complete.

If you press • EXIT, the process will

return to the previous step.

If you skip this step, the channel •

search can be performed in the TV Menu. (See page 31.)

The channel scan may take a while

to complete.

Status: Scanning..

Analog Channels: 0

Digital Channels: 0

Initial Setup Channel Scan

14%

Cancel

EXIT

8. Initial setup completed

Press • ENTER to exit the setup

wizard.

Congratulations !!

Completed Initial Setup.

Please press [ENTER] to exit the

wizard.

Initial Setup Complete

Back

Auto programming may take 20+ • minutes to complete. Please wait until you see the Auto programming complete message. The TV will then switch automatically to the ﬁrst channel found.

Direct Button Operation

Each time • INPUT is pressed, the

input source toggles.

If you press •

/b to select the

input source, press ENTER to conﬁrm your selection.

See page 17-18 for external equipment • connection.

MUTE

Mutes the current sound output. Press MUTE.

Mute can be canceled by using the • method below.

- Mute will be canceled if you press

VOL

+/-

or MUTE.

SLEEP

Allows you to set a time when the TV automatically switches to standby.

Press SLEEP.

The remaining time displays when •

the sleep timer has been set.

Each time you press • SLEEP, the

remaining time switches as shown below. Off, 10, 20, 30, 40, 50, 60, 90, 120

When set, the time automatically •

starts counting down.

If you want to adjust the sleep •

timer, you can press SLEEP twice then change the time setting.

One minute before the time •

expires, the remaining time displays every second.

Select • "Off" by pressing SLEEP to cancel the sleep timer.

The TV will enter standby mode (power • indicator lights red) when the remaining time reaches zero.

Changing Channels

You can change channels by pressing

r/s

or 0-9, or • (DOT).

Examples: To select a 1 or 2-digit channel number (e.

g., Channel 5):

Press 5 ENT. To select a 3-digit channel number (e. g.,

Channel 115):

Press 1 1 5 ENT. To select a 4-digit channel number (e. g.,

Channel 22.1):

Press 2 2 • (DOT) 1

ENT.

When selecting a 1-digit channel • number, it is not necessary to press 0 before the number.

Changing Volume

You can change the volume by pressing

VOLk/l on the TV or on the remote

control unit.

To increase the volume, press •

VOLk.

To decrease the volume, press •

VOLl.

INPUT

To view external source images, select the input

source using INPUT on the remote

control unit or INPUT on the TV.

Press 1.

INPUT.

A list of selectable sources •

appears.

Press 2.

INPUT

again to select the input

source.

An image from the selected source •

automatically displays.

Direct Button Operation

FLASHBACK

Press FLASHBACK to switch to the previously tuned channel.

Press • FLASHBACK again to

switch back to the currently tuned channel.

SURROUND

The surround function produces Surround effect from the speakers. Each time you press SURROUND, the mode changes between On and Off.

• On: Makes it possible to enjoy natural, realistic surround sound.

• Off: Outputs the normal sound.

You can have the same settings by • choosing “Surround” on the menu items. (See page 30.)

FREEZE

Allows you to capture and freeze a moving image that you are watching.

Press FREEZE.

A moving image is captured.• Press • FREEZE again to cancel the

function

AV MODE

AV MODE gives you several viewing options to choose from to best match the surrounding environment of the TV, which can vary due to factors like room brightness, type of program watched or the type of image input from external equipment.

Press AV MODE. Current AV MODE displays.

Press • AV MODE again before the

mode displayed on the screen disappears.

AUDIO

■

MTS/SAP stereo mode

The TV has a feature that allows reception of sound other than the main audio for the program. This feature is called Multichannel Television Sound (MTS). The TV with MTS can receive mono sound, stereo sound and Secondary Audio Programs (SAP). The SAP feature allows a TV station to broadcast other information, which could be audio in another language or something completely different like weather information.

You can enjoy Hi-Fi stereo sound or SAP broadcasts when available.

Stereo broadcasts: • View programs

like live sporting events, shows and concerts in dynamic stereo sound.

SAP broadcasts: • Receive TV

broadcasts in either MAIN or SAP sound.

MAIN sound: The normal program soundtrack (either in mono or stereo). SAP sound: Listen to a second language, supplementary commentary or other information. (SAP is mono sound.)

If stereo sound is difﬁcult to hear.

Obtain a clearer sound by manually •

switching to ﬁxed mono-sound mode.

You can change MTS as shown below to match the television broadcast signal.

Press AUDIO to toggle between audio modes.

Examples: when receiving MTS and SAP

MAIN + SAP mode:

MAIN SAP

MONO mode: MONO

Direct Button Operation

■

Digital broadcasting audio mode

The types of audio transmitted in a digital broadcast include SURROUND as well as MONO and STEREO. In addition, it is possible for multiple audio tracks to accompany a single video track.

Press MTS/SAP to toggle between audio modes.

Example: when receiving Digital broadcasting

STEREO (Audio1) STEREO (Audio2) SURROUND (Audio3)

MTS only operates while in TV mode.•

Closed Captions (CC)

Your TV is equipped with an internal Closed Caption decoder. It allows you to view conversations, narration and sound effects as subtitles on your TV. Closed Captions are available on some TV programs and on some VHS home video tapes at the discretion of the program provider.

Digital Closed Caption service is a new caption service available only on digital TV programs (also at the discretion of the service provider). It is a more ﬂexible system than the original Closed Caption system, because it allows for a variety of caption sizes and font styles. When the Digital Closed Caption service is in use, it will be indicated by the appearance of a 3-letter abbreviation that also indicates the language of the Digital Closed Captions: ENG (English), SPA (Spanish), FRA (French) or other language codes.

Not all programs and VHS videotapes offer closed captions.

In the Closed Caption system, there can be more than one caption service provided. Each is identiﬁed by its own number. The “CC1” to “CC4” services display subtitles of TV programs superimposed over the program's picture.

In the Closed Caption system, the “TEXT1” to “TEXT4” services display text that is unrelated to the program being viewed (e.g., weather or news). These services are also superimposed over the program currently being viewed.

Press 1. CC.

This will display the current Closed •

Caption information. Press CC to turn the Closed Caption on or off.

Caption Display will not work when • viewing a 480i, 480p, 720p, 1080i or 1080p input via the COMPONENT: Y-PbPr or HDMI inputs.

Closed Captions availability and content • depends on the broadcaster. Closed Caption are available when the Closed Caption icon is displayed on screen.

Closed Captions and Digital Captions • availability and content depends on the broadcaster. Closed Caption are available when the Closed Caption icon is displayed on screen

VIEW MODE

You can select the screen size.

Press VIEW MODE.

You can sequentially select a viewing mode that has its own aspect ratio.• Press • VIEW MODE to toggle between Stretch, Side Bar, Smart stretch, Zoom,

Dot by Dot, or Automatic.

■

For 4:3 programs

Example: Screen size images

Automatic Stretch Side Bar

S. stretch (Smart

stretch)

Zoom

Suitable for viewing subtitles and enlarging picture automatically to ﬁll the screen

This mode is useful for 1.78:1 DVDs. When viewing

1.85:1 DVDs, stretch mode will still show very thin black bands at the top and bottom of the screen.

Suitable for viewing conventional 4:3 programs in their normal format.

Suitable for stretching 4:3 programs to ﬁll the screen.

Suitable for viewing wide-screen 2.35:1 anamorphic DVDs in full screen.

■

For PC input

Example: Screen size images

Input signal Stretch Side Bar Dot by Dot

4:3

An image fully ﬁlls the screen.

Suitable for viewing conventional 4:3 programs in their normal format.

Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

Input signal Stretch Dot by Dot

16:9

An image fully ﬁlls the screen.

Detects the resolution of the signal and displays an image with the same number of pixels on the screen.

Direct Button Operation

For TV Mode

Some menu items may not be displayed depending on the selected input source.•

On-Screen Display Menu

Menu Items

Video Menu

AV Mode .................................................................29

Backlight .................................................................28

Brightness ............................................................... 28

Contrast ..................................................................28

Saturation ................................................................ 28

Hue .........................................................................28

Sharpness ............................................................... 28

Color Temperature ..................................................29

Warm ............................................................... 29

Normal ............................................................. 29

Cool ................................................................. 29

User ................................................................. 29

Advanced Video ......................................................29

DNR ................................................................. 29

MPEG NR ........................................................29

Adaptive Luma Control ..................................... 29

Flesh Tone .......................................................29

DI Film Mode .................................................... 29

Blue Stretch .....................................................29

Game Mode ..................................................... 29

HDMI Mode...................................................... 29

Adaptive Backlight ...........................................29

Audio Menu

Balance ................................................................... 30

Bass ........................................................................ 30

Treble ...................................................................... 30

Sound Surround ...................................................... 30

Equalizer .................................................................. 30

Speaker ................................................................... 30

SPDIF Type .............................................................30

Auto Volume Control ...............................................30

TV Menu

Tuner Mode ............................................................. 31

Auto CH Search ......................................................31

CH Skip ................................................................... 31

Audio Mode ............................................................. 31

Audio Language ......................................................31

Favorite Channels .................................................... 31

Setup Menu

OSD Language ........................................................ 32

View Mode ..............................................................24

Automatic......................................................... 24

Stretch ............................................................. 24

Side Bar ........................................................... 24

Smart stretch ...................................................24

Zoom ............................................................... 24

Blue Mute ................................................................ 32

Time Setup .............................................................. 32

Time Zone ........................................................ 32

Time ................................................................. 32

Sleep Timer ...................................................... 32

Auto Sleep .......................................................32

Caption ...................................................................32

Analog Closed Caption ..................................... 32

Digital Closed Caption ...................................... 33

Digital Caption Style .........................................33

Location ..................................................................33

Version Info .............................................................33

Reset ....................................................................... 33

Parental Menu

Channel Block ......................................................... 34

Program Block ........................................................35

Rating Enable ................................................... 35

U.S. TV Ratings ................................................ 35

U.S. Movie Ratings ........................................... 36

Canadian English Ratings ................................. 36

Canadian French Ratings .................................37

Open V-Chip .................................................... 37

Block Unrated .................................................. 37

Input Block .............................................................. 37

Change Password ................................................... 37

Clean All .................................................................. 37

USB Menu

Multi-Media .............................................................38