SHARP SERVICE MANUAL
ELECTRIC JAR POT
MODELS KP-19S
KP-30S/ST
KP-36S
In the interests of user-safety (Required by safety regulations
in some countries) the set should be restored to its original
condition and onlyparts identical to those specifi ed should
be used.
TABLE OF CONTENTS
NAME OF PARTS AND SPECIFICATIONS ................................................................................
CAUTIONS FOR USE .................................................................................................................
CLEANING AND CARE ..............................................................................................................
WIRING DIAGRAM AND CIRCIUT DIAGRAM ..........................................................................
COMPONENTS REPLACEMENT PROCEDURE .......................................................................
INSPECTION AFTER ASSEMBLING ..........................................................................................
TROUBLESHOOTING GUIDE ....................................................................................................
SERVICE PARTS LIST .................................................................................................................
SHARP CORPORATION
Page
2
3-4
4
5
6-10
11
12-13
14-20
Outer lid cover
Inner lid packing
Inner pot
Upper ring
Delivery base cover
Body
Water level indicator
Inner lid
NAME OF PARTS
Outer lid
Handle
Swivel base
Push button for
pouring water
Pour/Stop switch
Steam outlet
Refi ll level
“BOIL’’ indicator lamp
“WARM’’ indicator lamp
Model
Power consumption ( W )
Plug plate
Bottom cover
Power cord ass’y
Connector
(Connected to body)
SPECIFICATIONS
KP-19S
610 670
KP-30S/ST
Plug
KP-36S
Rated voltage ( V )
Capacity (max. water volume) ( l )
Pouring system
Outside dimensions (W x D x H) (mm.)
Weight (kg)
220
1.8
2.9 3.6
Manual air pressure operation
201 x 247 x 275 201 x 247 x 357 201 x 247 x 410
1.5 1.6
1.9
2
1. For power supply use the proper socket.
1.1 Do not connect too many loads to one outlet.
1.2 If any of the power supply cord, plug and connector is damaged or feel abnormally hot. Immediately
call the serviceperson to repair it. Otherwise, this will cause an electric shock or fi re.
2. Do not immerse the unit in water or splash it with water.
This will result in malfunctioning or electric shock.
3. Do not operate the unit without water in the pot.
This will cause malfunctioning or discolouring of the inner pot.
4. Close lid fi rmly.
Otherwise hot water outfl ow so much when tumbling.
5. Do not put milk, liquor, tea, ice cubes and etc. in the pot.
This will result in malfunctioning or electric shock.
6. The power cord ass’y (supplied) is only for the product. Do not use it for other apparatus or apply
the other type of power cord ass’y to this product.
7. When put water into the pot :
7.1 Be sure to keep the water level between the “Refi ll” level and “Full” level.
7.2 If water is put above the “Full” level, the hot water may be overfl ow from the spout during boiling.
7.3 Do not put water into the pot directly from the tap, because fl ooded water may intrude into the
mechanism and cause an electric shock and malfunctioning.
8. Location
8.1 Do not use or place the unit on an unstable, wet fl oor or adjacent to other heat generating apparatus,
as this will cause the unit to fall down, deform itself or malfunction.
8.2 Keep the pot away from child not to cause an accidental scald or injury.
9. When plugging the power cord ass’y :
Remove iron chip and dust from the connector plug and inner terminal.
10. When boiling and warming water :
10.1 In the beginning of operation, the unit may generate plastic smell or oily smell of the heater, but this
will hardly occur as the usage lasts.
10.2 Sounds are emitted during the boiling and warming. But this is quite normal.
10.3 Keep the power cord ass’y plugged during the warming, otherwise the water temperature goes
down gradually.
10.4 Sometimes exchange the water in the pot not to degrade water quality.
10.5 Disinfectant contained in tap water or some water may cause a smell when it is heated.
10.6 Pressing the push button with undue force may cause the hot water to scatter so as to result in scald
or injury.
10.7 If the water level in the pot go down below the “Refi ll” level during operation, be sure to add water.
Otherwise the unit may be damaged.
10.8 The inner lid becomes heated during operation; use a dish cloth or the like when removing it.
10.9 Do not carry the pot at the condition of inclining.
CAUTIONS FOR USE
3
11. After use
11.1 Pull out the plug from a wall outlet and detach the connector from the unit.
1 1.2 Detach the lid, and dispose hot water remained in the pot : if the hot water is left for a long time, this will
cause discolouring and corrosion of the inner pot. T ake care not to dispose hot water directly from the
spout. Splashed hot water from the spout may course scald.
12. Water discharge amount
This electrical thermo pot employs manual air-pressure system, in which the push button is pressed to
inject the compressed air in the bellows into the closed vessel, so as to allow the hot water to be discharged
out of the pot. Therefore, if the water temperature in the pot is high, the amount of water discharge is
increased because the air pressure is increased due to air expansion and steam generated in the pot;
reversely, the amount of the water discharge is decreased when the water temperature in the pot is low.
CLEANING AND CARE
CAUTION :
1. Cleaning
1.1 Body and Outer lid ass’y
Soak a soft cloth in water, squeeze properly and wipe carefully.
1.2 Inner pot
Soak a sponge with water , then rub the inside of the inner pot carefully . Rinse and drain suffi ciently
with water, then wipe off moisture in the inner pot. Do not splash water on parts other than the
inside of inner pot.
2. Against discoloring (into milk white, black, rain bow color, etc.)
It is adhesion of the impurities contained in the water. The following procedures are used to make them
unnoticeable.
2.1 Fill the vessel with water mixed with 50 g Citric Acid or Lemon Juice up to the “Full” level and let it boil.
DO NOT IMMERSE CORD PLUG OR BODY IN W A TER OR OTHER LIQUID. BEFORE CLEANING,
BE SURE TO DISCONNECT THE PLUG, POUR OUT THE REMAINED W A TER AND COOL DOWN
THE BODY . DO NOT USE POLISHING POWDER, HARD BRUSH, THINNER ALCOHOL OR OTHER
SOLVENT : OTHERWISE THE SURFACE MAY BE DAMAGED OR DISCOLOURED.
2.2 Keep warm for about 1 hour, then pour out the lemon water as usual.
2.3 Rinse thoroughly with water until the lemon smell is removed.
However the thermal discoloring due to heating without water can not be restored.
3. When the unit is not used for long periods of time :
Rinse the inner pot with water, drain off by placing the body upside down.
Then wipe off moisture in the inner pot well.
4. Rusty Spots
Rusty Spots result from oxidization of iron which is contained in the water.
Scrub them off with a nylon cleaner or such (except “Polyfl on” Scrub them off with a sponge).
4
WIRING DIAGRAM
CIRCUIT DIAGRAM
5
COMPONENTS REPLACEMENT PROCEDURE
In disassembling or assembling the parts other than the lid assembly, the work can be done
easily when the lid assembly and body assembly are left connected with each other.
INNER LID PACKING REPLACEMENT
The inner lid packing is non-durable parts. When it is diffi cult to pour water, please change the inner lid
packing. Fig. 1 and Fig. 2
How to remove
Pull the inner lid packing off from the inner lid.
Fig. 1
How to attach
Remove the inner lid packing as directed in the following
illustration.
Be sure that the inner lid packing can cover tightly into the
inner lid brim.
Inner lid
Inner lid packing
Correct
Incorrect
Fig. 2
6
Loading...