Sharp GX-M10H-OR, GX-M10H-RD User Manual

MODEL

Code 93

; Font Facename:

Code93

TINSEA414AWZZ

*TINSEA414AWZZTJ*|

GX-M10H(OR) GX-M10H(RD)

PORTABLE CD STEREO SYSTEM

This quick Start Guide will help you to correctly install and operate your system. Illustration printed in this quick guide are for the model GX-M10H(OR)

Placing the unit

To get the best display viewing angle, place the unit as below.

Accessories

(RRMCGA292AWSA)

(UM/SUM-3, R6, HP-

7 or similar) x 1

Turn on your system

The first time the unit is plugged in with AC power, the unit will enter the demonstration mode.

1 Press the ON/STAND-BY button to turn the power on.

Position 1

XOX-M10

BG MO C ISU OB

M LE AB T

- On the shelf /

ROP

table.

Foot cushion 1 and 2 touching the surface.

Position 2

- On the floor /

GX-M10 B COOMBOX I S U

M OPRTABLE

ground.

Foot cushion 2 and 3 touching the surface.

Remote control battery installation

Use an “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).

1 Open the battery cover.

2 Insert the batteries as shown.

System connections

Car adaptor (not supplied) Socket: DC 12 V 4.5 A

PORTABLE MUSIC BOOMBOX GX-M10

To DC IN 12 V

socket

TIMER

REMOTE SENSOR

3 Close the cover.

Video Cable

(not supplied)

To AC INPUT socket

Wall socket AC 110 - 240 V ~ 50/60 Hz

TINSEA414AWZZ

12H R KI 1

Listening to the iPod, iPhone and iPad

iPod, iPhone and iPad connection (USB only)

Insert the connector to the iPod, iPhone or iPad.

iPad

Connector

2 Place the iPad to the stand for iPad.

iPad

Stand for iPad

3 Connect the iPod, iPhone or iPad to the unit via USB

connector.

Note:

USB terminal does not support VIDEO out.

iPod, iPhone or iPad playback (USB only)

Press the ON/STAND-BY button to turn the power on.

Press the USB button on the remote control or the

main unit to select USB function. Connect iPod, iPhone or iPad to the unit. “USB/iPod” will

appear.

Track number

Press the USB / button to start playback.

iPod and iPhone connection (Dock only)

Caution:

Unplug all accessories from the iPod or iPhone before inserting it into the dock. Note:

Do not use the docking station to connect your iPad.

Open the iPod door by pushing the

iPod door open knob to the area marked ‘ ’. Cautions:

Close the iPod door if not in use. Do not press the iPod door downwards when it is open as it may cause damage and injury.

Dock your iPod or iPhone into the unit.

iPhone (bottom)

Dock connector

Dock for iPhone

iPod or iPhone playback (dock only)

Press the ON/STAND-BY button to turn the power on.

Press the iPod / button on the remote control or

the main unit to select iPod function. Insert iPod or iPhone unit into the dock of main unit.

“DOCK OK” will appear. Make sure to close the iPod

door before playback.

Press the iPod / button to start playback.

To disconnect iPod, iPhone or iPad

It is safe to disconnect iPod, iPhone and iPad even during

playback. However attention should be drawn when

removing the iPod or iPhone from docking station to

avoid damage.

iPhone

iPod door

Connecting a guitar / microphone Listening to a CD or MP3/WMA disc

ON/STAND-BY

Microphone or guitar (not supplied)

Ø 6.3 mm monoaural

cable (not supplied)

Set the guitar/microphone volume (GAIN) knob to the minimum level.

Connect a guitar/microphone to the correct input socket. Make sure

that the cable has a 6.3 mm (1/4”) diameter plug.

Arrange the guitar/microphone cables into the grooves of the cable

holder on the left or the right side of the unit. Then, thread the cable through the bottom of the unit. Do not let the cables to be on top of the unit when using guitar/microphone as it may cause the unit to roll over causing damage and injury.

Thread the cables under

Connect the cables to a guitar/microphone.

Select a source.

 To mix a guitar or microphone sound with a source sound,

select the playback source (iPod/CD/USB/Audio In/Tuner).

 To play a guitar or using the microphone only, select ’AUDIO IN’

function. Make sure there is no playback from Audio In connection.

Adjust the volume (GAIN) knob on the connected equipment.

Cable holder

the unit

Press the ON/STAND-BY button to turn the power on.

Press the CD / button on the remote control or the main unit

to select CD function.

Open the CD compartment by pushing the CD compartment open

knob to the area marked ‘ ’.

Place the disc on the spindle, label side up.

Close the CD compartment.

Press the CD / button to start playback. After the last track is

played, the unit will stop automatically.

PORTABLE MUSIC BOOMBOX GX-M10

TIMER

REMOTE SENSOR