SHARP GX-CD1200W Service Manual

Page 1
GX-CD1200W
SERVICE MANUAL
No. S5039GXCD1200
PORTABLE CD STEREO
COMPONENT SYSTEM
GX-CD1200W(BK)
MODEL GX-CD1200W(GL)
• In the interests of user-safety the set should be restored to its original condition and only parts identical to those specified should be used.
CONTENTS
Page
SPECIFICATIONS ...............................................................................................................................................................1
VOLTAGE SELECTION.......................................................................................................................................................2
AC POWER SUPPLY CORD AND AC PLUG ADAPTOR ................................................................................................... 2
FITTING OF DIAL POINTER ...............................................................................................................................................2
NAMES OF PARTS ............................................................................................................................................................. 3
DISASSEMBLY....................................................................................................................................................................4
REMOVING AND REINSTALLING THE MAIN PARTS.......................................................................................................5
ADJUSTMENT .....................................................................................................................................................................6
SCHEMATIC DIAGRAM / WIRING SIDE OF P.W.BOARD...............................................................................................10
VOLTAGE ..........................................................................................................................................................................18
WAVEFORMS OF CD CIRCUIT........................................................................................................................................ 19
FUNCTION.........................................................................................................................................................................24
PARTS GUIDE / EXPLODED VIEW
SPECIFICATIONS
General
Power source: AC 110-127 V/220-240 V, 50/60 Hz
DC 15 V [“D” size (UM/SUM-1, R20 or HP-
2) battery x 10]
Power consumption: 31 W Output power: PMPO; 200 W (Total)
(AC operation) MPO; 50 W (25 W + 25 W) (AC operation) RMS; 25 W (12.5 W + 12.5 W) (DC operation, 10 % T.H.D.)
Input terminal: Mixing microphone(monaural); 600 ohms Output terminal: Headphones; 16-50 ohms
(recommended; 32 ohms)
Dimensions: Width; 300 mm (11-13/16")
Height; 262 mm (9-1/2") Depth; 220 mm (8-11/16")
Weight: 4.1 kg (9.1 lbs.) without batteries
Compact disc player
Type: Compact disc Signal readout: Non-contact, 3-beam semi-conductor laser
pickup
Audio channels: 2 Filter: 8-times oversampling digital filter D/A converter: 1-bit D/A converter Wow and flutter: Unmeasurab le
(less than 0.001 % W. peak)
Radio section
Frequency range: FM; 88 - 108 MHz
SW1; 2.3 - 7.3 MHz SW2; 7.3 - 22 MHz MW; 526.5 - 1,606.5 kHz
Tape recorder section
Frequency response: 60 - 12,000 Hz (Normal tape) Signal/noise ratio: 40 dB (TAPE 1, recording/playback)
55 dB (TAPE 2, playback)
Wow and flutter: 0.15 % (WRMS) Motor: DC 9 V electric governor Bias system: AC bias Erase system: Magnet erase
Speaker section
Type: 2-way type Speakers: 12 cm (4-3/4") free-edge speaker x 2
Tweeter x 2
Maximum input power: 25 W Rated input power: 12.5 W Impedance: 8 ohms Dimensions: Width; 235 mm (9-1/4")
Height; 262 mm (10-5/16") Depth; 220 mm (8-11/16")
Weight: 1.8 kg (4.0 lbs.)/each
Specifications for this model are subject to change without prior notice.
SHARP CORPORATION
– 1 –
This document has been published to be used for after sales service only. The contents are subject to change without notice.
Page 2
GX-CD1200W
FOR A COMPLETE DESCRIPTION OF THE OPERATION OF THIS UNIT, PLEASE REFER TO THE OPERATION MANUAL.
VOLTAGE SELECTION
Before operating the unit on mains, check the preset voltage. If the voltage is different from your local voltage, adjust the voltage as follows: Slide the voltage selector with a screwdriver to the appropriate voltage number (AC 110V-127V or AC 220V-240V).
AC POWER SUPPLY CORD AND AC PLUG ADAPTOR
QACCE0007AW00
QACCL0002AW00
FITTING OF DIAL POINTER
1. Remove the Main PWB, the Graphic Equalizer PWB, the Volume PWB and the Fine Tuning PWB. (See Figure 4-2 in the "Disassembly" on page 4.)
2. Remove the dial pointer guide and PWB.
3. Insert the dial pointer from , lead it under , hang it on the tuner gear and then pass it through .
4. Replace the Main PWB, the Graphic Equalizer PWB, the Volume PWB and the Fine Tuning PWB.
5. Rotate the tuning knob in the arrow direction until it stops. (Set the tuner variable capacitor to "0" point (F-LOW state).)
6. Adjust the dial pointer so that its stopper becomes the Figure 2-2 position. (Adjust the engagement of the pointer gear and the tuner gear to get the minimum space between the PWB and the stopper.) This position is the "0" point.
7. Screw up the PWB and the dial pointer guide.
A
B
C
QACCA0001SJ00
QPLGA0250AFZZ QPLGA0253AFZZ
"0" Point
Dial Pointer(211)
Front Cabinet
Tuning Knob
C
Dial Pointer Guide (218)
PWB
Tuner Gear
B
Fine Tuning PWB
Screw(601) ø3x10mm
A
Dial Pointer(211)
Graphic Equalizer PWB
Volume PWB
– 2 –
Main PWB
Figure 2-1
Make the minimum space.
PWB
Dial Pointer
Stopper
Pointer Gear
Tuner Gear
Main PWB
Front Cabinet
Variable Capacitor
Figure 2-2
Page 3
NAMES OF PARTS
44
45 46
47
48
1. CD Compartment
2. CD Eject Button
3. Track Number Indicator
4. (CD) Play Indicator
5. (CD) Pause Indicator
6. Extra Bass Control
7. Graphic Equalizer Controls
8. Power/(TAPE 2) Play Direction Indicators
9. (CD) Track Down/Review Button
10. (CD) Track Up/Cue Button
11. (CD) Stop Button
12. (CD) Play/Pause Button
13. Fine Tuning Control
14. Built-in Microphone
15. Volume Control
16. Headphone Socket
17. Mixing Microphone Socket
18. Function Selector Switch
19. (TAPE 1) Cassette Compartment
20. Tuning Control
21. FM Stereo Indicator
22. Surround Indicator
23. Surround Switch
24. Band Selector Switch
25. Dubbing Speed/Built-in Microphone/FM Mode Switch
26. (TAPE 2) Cassette Compartment
27. (TAPE 1) Record Button
28. (TAPE 1) Play Button
29. (TAPE 1) Rewind Button
30. (TAPE 1) Fast Forward Button
31. (TAPE 1) Stop/Eject Button
32. (TAPE 1) Pause Button
33. (TAPE 2) Reverse Mode Switch
34. (TAPE 2) Play Button
35. (TAPE 2) Fast Wind Buttons
36. (TAPE 2) Stop/Eject Button
37. (TAPE 2) Direction Switch
72189
6
14 15
16 17 18
19
28 29 30 31 32
27
(Continued)
4 5
33 34
3
10241125122613
35 36
GX-CD1200W
1
2
20
22 23
37
38. FM/SW Telescopic Rod Aerial
39. Beat Cancel Switch
40. Speaker Terminals
41. AC V oltage Selector
42. AC Power Input Socket
43. Battery Compartment
44. Tweeter
45. Bass Reflex Duct
46. Woofer
47. Speaker Release Lever
48. Speaker Wire
38 39 40
41 42 43
– 3 –
Page 4
GX-CD1200W
Rear Cabinet
(E1)x3 ø3x10mm
(E2)x2 ø4x16mm
(E4)x2 ø3x10mm
Power Transeformer
Voltage Selector
AC Socket
(E3)x1
Power PWB
Terminal B PWB
Terminal A PWB
(E5)x2
DISASSEMBLY
Caution on Disassembly
Follow the below-mentioned notes when disassembling the unit and reassembling it, to keep it safe and ensure excellent performance:
1. Take cassette tape out of the unit.
2. Be sure to remove the power supply plug from the wall outlet before starting to disassemble the unit and remove the batteries from the unit.
3. Take off nylon bands or wire holders where they need to be removed when disassembling the unit. After servicing the unit, be sure to rearrange the leads where they were before disassembling.
4. Take sufficient care on static electricity of integrated circuits and other circuits when servicing.
MAIN UNIT
STEP REMOVAL PROCEDURE FIGURE
1 Front Cabinet/ 1. Battery Compartment Lid. 4-1
Rear Cabinet ................................. (A1)x1
2. Screw ................... (A2)x5
3. Screw ................... (A3)x3
4. Socket .................. (A4)x1
2 CD Player Unit 1. Screw................... (B1)x2 4-2
2.Socket ................... (B2)x1
3 Main PWB/ 1. Knob..................... (C1)x1 4-3
Graphic Equalizer 2. Socket .................. (C2)x3
PWB/ 3. Screw ................... (C3)x5
Volume PWB/ 4. Screw ................... (C4)x2
Fine Tuning PWB 5. Mic ....................... (C5)x1
4 Tape mechanism 1. Open the cassette holder. 4-3
2. Screw ................... (D1)x6
5 Power PWB/ 1. Screw ................... (E1)x3 4-4
Terminal A PWB/ 2. Screw ................... (E2)x2
Terminal B PWB 3. Bracket................. (E3)x1
4. Screw ................... (E4)x2
5. Hook..................... (E5)x2
6 CD Servo PWB/ 1. Screw ................... (F1)x7 5-1
CD Control PWB/ 2. Socket .................. (F2)x3
7 CD Mechanism 1. Screw ...................(G1)x1 5-1
SPEAKER UNIT
STEP REMOVAL PROCEDURE FIGURE
1 Speaker 1. Screw ................... (H1)x5 5-2
2. Front Panel ..........(H2)x1
3. Screw ................... (H3)x4
Main PWB
(B1)x2 ø3x10mm
CD SERVO PWB
Front Cabinet
Main PWB
(C4)x2 ø3x10mm
(D1)x4 ø3x10mm
(B2)x1
(C3)x5 ø3x10mm
Figure 4-2
Fine Tuning
PWB
(C2)x3
Figure 4-3
Volume PWB
Graphic Equalizer PWB
(C5)x1
(D1)x2 ø3x10mm
CD Player Unit
Front Cabinet
(C1)x1
Nat
Washer
Open
Cassette Holder (Left/Right)
Tape Mechanism
(A3)x3
ø3x20mm
(A2)x3
ø3x6mm
(A2)x1
ø3x6mm
(A1)x1
Figure 4-1
Rear
Cabinet
(A4)x1
Front
Cabinet
(A2)x1
ø3x6mm
Figure 4-4
– 4 –
Page 5
GX-CD1200W
CD Servo
PWB
(F1)x1 ø3x10mm
(F1)x3 ø3x10mm
Switch PWB
(F1)x3 ø3x10mm
(F2)x1
Figure 5-1
(G1)x3 ø3x10mm
CD Control PWB
(F2)x2
CD Mechanism
CD Player Unit
Front Panel (H2)x1
Woofer
Main Unit
Tweeter
(H3)x4 ø3x10mm
Speaker Release Lever
Figure 5-2
Speaker Cord Holder
Speaker Box
Speaker Cord
Driver
(H1)x5 ø4x16mm
REMOVING AND REINSTALLING THE MAIN PARTS
CD MECHANISM SECTION
Perform steps 1,2,6 and 7 of the disassembly method to remove the CD mechanism.
How to remove the pickup (See Fig. 5-3.)
1. Remove the hooks (A1) x 2 pcs., to remove the CD Mechanism Cover (A2) x1 pc.
2. Remove the screws (A3) x 2 pcs., to remove the shaft (A4) x1 pc.
3. Remove the stop washer (A5) x1 pc., to remove the gear (A6) x 1 pc.
4. Remove the pickup.
Note : (Figure 5-1 and Figure 5-3)
After removing the connector for the optical pick-up from
the connector, wrap the conductive aluminium foil around the front end of connector to protect the optical pick-up from electrostatic damage.
(A1)x2
(A3) x2
ø2.6 x6mm
Pickup
Shaft (A4) x1
(A2)x1
Figure 5-3
Gear (A6) x1
CD Mechanism
Stop Washer (A5) x1
– 5 –
Page 6
GX-CD1200W TAPE MECHANISM SECTION
Perform steps 1, 2, 3 and 4 of the disassembly method to remove the mechanism block.
How to remove the record / playback, playback and erase heads (See Figs. 6-1 and 6-2.)
1. Remove the screws (A1) x 2 pcs., to remove the record/ playback head.
2. Remove the hooks (A2) x 2 pcs., toward the center position
as shown in Fig. 6-1. and then extract the erase head upward.
3. Remove the screws (B1) x 2 pcs., to remove the playback head.
Note:
After replacing the heads and performing the azimuth adjust­ment, be sure to apply screw lock.
How to remove the pinch roller (See Fig. 6-3.)
1. Carefully bend the pinch roller pawl in the direction of the
arrow <A> , and remove the pinch roller (C1) upwards.
How to remove the motor (See Fig. 6-4.)
1. Remove the belt.
2. Remove the screws (D1) x 4 pcs., to remove the motor bracket.
3. Remove the screws (D2) x 3 pcs., to remove the motor.
Note:
When mounting the motor, pay attention to the motor mount­ing angle.
Hook (A2) x2
Erase Head
(B1) x1 ø2x7mm
(A1) x1 ø2x7mm
(A1) x1 ø2x3mm
Figure 6-1
(B1) x1 ø2x3mm
TAPE 1
Record/Playback Head
TAPE 2
Playback Head
How to remove the belts (See Fig. 6-5.)
1. Remove the main belt (E1) x 1 pc., at the tape 1 side from
the motor pulley.
2. Remove the main belt (E2) x 1 pc., at the tape 2 side from
the motor pulley.
3. Remove the REW/FF belt (E3) x 2 pcs., from the REW/FF
roller.
4. Put on the belts in the reverse order of removal.
Note:
When putting on the belt, ascertain that the belt is not twisted, and clean it.
Motor
TAPE 2
REW / FF Belt (E3) x1
TAPE 2 Main Belt
TAPE 1 Main Belt
Motor Main
Belt (E1) x1
TAPE 1
Pinch Roller (C1)
( D1 ) x2 ø2 x 4mm
Figure 6-2
Figure 6-3
Motor
Pinch Roller Pawl
<A>
( D1 ) x2 ø2 x 4mm
Motor Bracket
( D2 ) x3 Special Screw
Main Belt (E2) x1
Figure 6-5
REW / FF Belt (E3) x1
– 6 –
Motor
Figure 6-4
Motor Bracket
Page 7
ADJUSTMENT
10 pF
1M ohm
10K ohm
TO FREQUENCY COUNTER
Pin 13 of IC2
Pin 21 of IC2
FET: 2SK212 (or Other 2SK Type FET.)
G
D
S
0.1 µF
GX-CD1200W
MECHANISM SECTION
• Driving Force Check
Torque Meter
Play: TW-2412 Tape 1: Over 60 g
Specified Value
Tape 2: Over 50 g
• Torque Check
Torque Meter
Play: TW-2111 30 to 70 g.cm 27 to 60 g.cm Fast Forward: TW-2231 Over 55 g.cm 55 to 120 g.cm Rewind: TW-2231 Over 55 g.cm 55 to 120 g.cm
Specified Value
Tape 1 Tape 2
Head Azimuth
Test Tape
MTT-114 Headphones Socket
Instrument Connection
(Load resistance: 32 ohms)
• Tape Speed (Normal only)
Test Tape
MTT-111 Tape 1,2:VR102 3,000 ± 60 Hz Headphones
Adjustment
Point
Specified
Value
Instrument
Connection
Socket (Load resistance:
32 ohms)
DECK SECTION
• Bias Oscillation
• Beat Cancel Switch: C
Adjustment Point Specified value Instrument
L301 100 kHz + 4 kHz Pin 1 of CNS102
Specified Value
Beat Cancel A: 104 ± 4 kHz
B: 94 ± 4 kHz C: 100 ± 4 kHz
• Playback Amplifier Sensitivity Check
Test tape
MTT-118 2.5 V ± 3 dB Speaker terminal
Specified value Instrument Connection
(Load resistance: 8 ohms)
Connection
TUNER SECTION
fL: Low-range frequency fH: High-range frequency
• FM IF/RF
Test Stage
FM IF L9 Input: FM Antenna FM Detection L10 Output:Pin 9 of IC2
FM Band fL: L1 Input: Antenna Coverage fH: TC1 Output: Headphone Socket FM Tracking fL(88.0 MHz): L2 (Load resistance:
Specified Value/
Adjusting
Point
fH(108 MHz): TC2 32 ohms)
• AM IF/RF
Test Stage
AM IF L11
MW Band fL: L6 Coverage fH: TC3
MW Tracking fL(600 kHz): L3
SW1 Band fL(2.3 MHz): L7 Coverage fH(7.3 MHz): TC5
SW1 fL(2.6 MHz): L4 Tracking fH(6 MHz): TC6
SW2 Band fL(7.3 MHz): L8 Coverage fH(22 MHz): TC7
SW2 fL(8.5 MHz): L5 Tracking fH(19 MHz): TC8
Specified Value/
Adjusting
Point
Input: Antenna Output: Pin 9 of IC2
Output: Headphone Socket
fH(1,400 kHz):TC4
• VCO Frequency
Adjustment
Point
VR1 76 kHz ± 200 Hz Pin 13, Pin 21 and ground
Specified value Instrument Connection
Note:
After preparing the test circuit shown in Fig. 7, connect the Pin 13, Pin 21 and ground of the IC2 with the test circuit, and measure the value.
Instrument
Connection
Instrument
Connection
Input: Antenna
(Load resistance: 32 ohms)
of IC2
Figure 7 VCO FREQUENCY TEST CIRCUIT
– 7 –
Page 8
GX-CD1200W
SW401
SW1 BAND COVERAGE
SW2 BAND COVERAGE
SW103
SW1
FM TRACKING fH
L8
L7
L2
TC4
TC2
TC5
fH fL
TC7
fH fL
TC6
TC3
TC1
SW1 TRACKING fH
MW TRACKING fH
MW BAND COVERAGE fH
fH
FM BAND COVERAGE
fL
MW BAND COVERAGE fL
MAIN PWB
L6
VCO
VR1
CF1
FM TRACKING fL
AM IF
L11
CF3
12
13
IC1
9
IC2
CF2
1
21
24
L10
FM DETECTION
FM IF
L1
L9
L4
L3
TC8
L5
fH
SW2 TRACKING
fL
SW1 TRACKING fL
MW TRACKING fL
MAIN PWB
CNP103
IC502
TAPE SPEED
VR102
CNP501
SPEAKER TERMINALS
Figure 8 ADJUSTMENT POINTS
– 8 –
Q603
Page 9
GX-CD1200W
CD SECTION
Since this CD system incorporates the following automatic adjustment function, when the pickup is replaced, it is not necessary to reajust it. Since this CD unit does not need adjustment, the combination of PWB and laser pickup unit is not restricted.
TEST MODE
Start
While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD". (To serial No.006XXXXX) While holding down the "STOP" button, move the FUNCTION/POWER switch to "CD". (From serial No.007XXXXX)
Note
1. When the CD LID switch is in the OFF position, (CD LID is open) the unit will be able to enter the test mode. However, can use the "UP/CUE" and "DOWN/REVIEW" button only.
2. You can only move the pickup.
3. The LCD display should be the same as it is for normal CD operations.
Operation
The use of the "UP/CUE" button will move the pickup to the outermost position. The use of the "DOWN/REVIEW" button will move the pickup to the innermost position.
LCD MODE
Start
Display
After connecting of the 10k resistor between IC802 27 pin and GND and holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD".
LASER LIGHTING CONFIRMATION
1. Remove the front cabinet according to the disassembly method.
2. Short the TP of the Figure 9 to turn on the CD LID SW 810.
3. While holding down the "PLAY" button, move the FUNCTION/POWER switch to "CD".
4. Open the CD LID and press the PLAY button. The laser lights up for a few seconds. (At this time, the pickup lens moves up and down and adjusts the focus to check if there is a disc or not.)
CD CONTROL PWB-C2
SW801 PLAY/ PAUSE
SWITCH PWB-C3
SW810 OPEN/CLOSE
TP
FW1
R847
SW802 STOP
10
13
10
12
12
12
R861
R846
R863
821
R822
R844
C825
R848
R849
FW801
L802
FW801
C824
30
C823
31
SW804 REVIEW/ TRACK DOWN
1
20
25
35
40
1
15
1
5
10
IC802
60
100
95
65
16
C852
SW803 CUE/ TRACK UP
1
2
2
3
6 5 4
804
3
3
1
Q803
R858
Q804
11
1
CNS804
LCD801
2345 178 6
15
14
4
17
C846
C855
C847
R839
90
85
81
80
75
70
R865
X801
R832
C844
C843
CD SERVO PWB-C1
C853
C848
R835
C845
L803
C840
C849
R836
R840
C850
C858
R857
L801
C851
Figure 9
– 9 –
Page 10
GX-CD1200W
V
5 T W
C
G
C
E
0
0
FM SIGNAL
A
ROD ANTENNA(253)
B
C
CNS804
6 5
CNP804 TO CD
D
SERVO PWB P13 11-G
E
F
G
H
SIDE-A L-CH
SIDE-B
SIDE-A R-CH SIDE-B
L-CH
R-CH
ERASE HEAD
TAPE1
RECORD/PLAYBACK HEAD
4 3 2 1
J151 MIC JACK
MIC151 BUILT-IN MICROPHONE
TAPE2
PLAYBACK HEAD
SW504-A TAPE2 DIRECTION
A
B
A
B
SW504-B TAPE2 DIRECTION
1 2
3
1 2 3 4
PLAYBACK SIGNAL
R4
7
330K
C13
0.022
C12 3P(CH)
0V
TC1
VC1
22P(CH)
L9
R3 47
1
CF2 FM IF
SW1-E
C19
BAND
330P
SELECTOR
FM
MW SW1 SW2
C20
0.0022
VC3
C27
0.0047
R166 560
+B
0V(0V)
R168 10K
0V(0.7V)
D163 DS1SS133
R169
Q153
10K
MIC AMP.
KTC3199 GR
( ):RECORD
(0V)
0V
C113
4.7/50
R101
100
C111
R109
0.015
6.8K
(ML)
R121 10K
R107 10K
C107
C109
47/10
330P
C112
0.015 (ML)
C110
47/10
MATAL
NF
OUT
MATAL
NF
OUT
C108 330P
R108 10K
R110
6.8K
R102 100
R302 100
SW101-E RECORD/ PLAYBACK
R303
C301 100/10
100
R105 180K
PRE
A/B
OUT
MIX
PRE
OUT
OUT
6 7 8 9 10 11 12
R106 180K
C114
4.7/50
R
P
C18 10/16
R5 100
3
2
TC3
C21 5P (UJ)
TC5
TC7
R122 10K
R7 820K
24
AM OSC
1
NORMAL
+B
VCC
R301 330
C22
0.022
23
STB
FM IF IN
C24
0.022
C25
0.022
L7 SW1 OSC.
L8 SW2 OSC.
C26
0.022
SW103-A DUBBING SPEED/MIC
HIGH
MIC
+B
C127
330/10
M/N GND1
R123 10K
R124 10K
SW1-A BAND SELECTOR
SW1-C BAND SELECTOR
BI804
6 5 4 3 2 1
CNS101
CNS102
D1 DS1SS133
SW1-B BAND SELECTOR
CF1
FM BAND PASS
FILTER
1 2 3
MW
SW1 SW2
FM MW
SW1
SW2
VC4
FM
MW
SW1 SW2
R352
R-CH
47K
GND(A) L-CH A-GND D-GND +8V(SERVO)
0V(0V)
3
Q154 KRA102M MIC AMP.
C151
0.33/50
R151
2.2K
CNP101
1 2 3
1 2 3 4
CNP102
SW102
BEAT CANCEL
C B A
C307 150P
MW/SW1 SIGNAL
RF AMP
0.9V
1
1.6V
C5
0.001
FM TRACKING
C4 24P
L2
(CH)
C7
0.0047
TC4
TC6
TC8
R351 47K
( ):CD FUNCTION
0V(9V)
2 0V(9V)
0V
1
0V
R153
1.3V
2.2K
R152
C154
4.7K 47/10
C152 10/16
L103 22mH
C131 120P
SW101-A~D RECORD/ PLAYBACK
R
SW101-D SW101-B
150P
R P
C134 150P
C132 120P
L104 22mH
C305
0.0015
(ML)
C306 390P
2
TC2
R1 10
C6
0.0047
L3,4 MW/SW1 BAR ANTENNA
R353 27K
TA2011S
MIC AMP.
C137
0.0015(ML)
R135 10K
P
R P
SW101-C SW101-A
R P
L301 BIAS OSC.
C304
0.022
FM
R354 27K
1
C133
IC1
TA7358AP
FM FRONT END
MIX
7.1V
1.6V
C2
5P(CH)
VC2
C8
0.022
L3 MW
L4 SW1
L5 SW2
ANTENNA
IC151
0V
4 3 2
0.9V
C155 10/16
R154 560
R136 10K
C138
0.0015(ML) R306
47
C303
0.0056 (ML)
6.4V
OSC
8
9
6 543
7V
7.2V
7.2V
C10 15P(CH)
R2 33
L1
FM
C11
OSC.
D2
DS1SS133
FM IF
C9
0.022
SW1-D
FM
BAND
MW
SELECTOR SW1 SW2
C14 5P(CH)
TC9
FINE
TNNING
C15
0.022
R165 10K
6V
7
C157
1.9V
1/50
5
( ):HIGH
6
C156 100/10
0V(0V)
R161 1M
R173 10K
(0.7V)
Q156 KTC3199 GR LINE AMP.
C101
C103
470P
470P
C105 330P
24 23 22 21 20 19 18 17 16 15 14 13
CH2/A
CH2/B
CH1/BCH1/A
1 2 3 4 5
IC101 TA8189N
RECORD/PLAY AMP.
C106 330P
C102 470P
C104
470P
Q301 KTC3203 Y BIAS OSC.
( ):RECORD
(3V)
R305 27K
(0.7V)
(0.1V)
C302
0.0022
R304
(ML)
10
MAIN PWB-A1/VOLUME PWB-A3/FINE TUNING PWB-A4
C23 220/10
DETECTION
C17
0.022
22
21
+B
IC2
AM RF
LA1805 FM/AM IF MPX.
AM MIX
L11
AM IF
L6 MW OSC.
SW101-F
BAND SELECTOR
P
R172 10K
D152
DS1SS133
R100 150
C115
4.7/50
C128
2.2/50
R113 120K
REC OUT
REC OUT
R114 120K
C129
22/16
C116
4.7/50
R116 680
R115
C118
680
REC NF
REC NF
10/16
FM
L10
RECORD SIGNAL
FM STEREO
C31
0.0047(ML)
R8
R9
3.9K 12K
C32
0.0082(ML)
19 18 17 16 15 14 13 12
AM IN
AM OUT
IF AD
DET OUT
GND
AM IF
7
5
8
6
CF3
455KHz
3
C37
AM IF
0.012 (ML)
R12
2
1K
SW1-F BAND SELECTOR
R13 100
C30
0.022
FM
C43 220P
MW SW1 SW2
C119
0.033
(ML)
R112 22K
C160 22/16
C123
0.01
C125
4.7/50
C126
4.7/50
FM
MW
SW1-G
BAND
SELECTOR
SW1 SW2
D156
DS1SS133
D158 DS1SS133
R177 1K
C124
0.01
AGC
4 3 2
C29 22/16
FM
MW SW1
SW2
R10 47
R11 47
R
C158 47/25
R170 33K
R111 22K
R117 330K
R119 100
C117
10/16
C121 330P
REC IN
REC IN
C122 330P
R120 100
R118 330K
20
FM DET
1
D154 DS1SS133
ALC
GND
C120
0.033 (ML)
C34 470P
MPX IN
IF AD
C39 1/50
R15 10K
D165 DS1SS133
C159 47/25
D162 DS1SS133
R132
1.2K
C35
3.3/50
C33
3.3/50
L-CH
9
R17
2.7K
SW1-H
BAND
SELECTOR
C42
0.022
D164 DS1SS133
R171 33K
R174 22K
R133 82K
R131
1.2K
R134 82K
+B
R14 100K
10
SW103-B FM MODE
MO/ST
R-CH
C40 1/50
R16 10K
R18
2.7K
+B
+B
FM MONO
C36
0.0015
N.C.
VCO
AM/FM
11
C38
0.012 (ML)
VR1 10KB
VCO
TP1 VCO 76KHZ
C41 1/50
R20 10
R129 150K
TUNER
TUNER
SW1 TRACKING
R19 15K
+B
+B
R130 150K
CD
TAPE
SW501-A FUNCTION SELECTOR
CD
TAPE
SW501-B FUNCTION SELECTOR
SW501-C FUNCTION SELECTOR
TUNER
TAPE
9V
Q601 KRC102M
CD
R-CH
1
L-CH
0V
R181 1K
fH
TC6
SW1 COV
fL
L4
Q181 KTC3199 GRAPHI EQUALIZ
R183 330K
C181
2.7V
1/50
0.9V
0.3
C183
R1
220P
22
R1
C184
22
220P
C182
2.7V
1/50
0.9V
R128 22K
R127 22K
R184 330K
0.3V
Q182 KTC3199 GRAPHI EQUALIZ
+B
+B
R511 10K
Q K S
R182 1K
0V 23
• NOTES ON SCHEMATIC DIAGRAM can be found on page 18.
1
2
34 5
Figure 10 SCHEMATIC DIAGRAM (1/4)
– 10 –
6
Page 11
fHfLTC6
L4
R183 330K
C181 1/50
C182 1/50
182
K
R184 330K
R127 22K
R128 22K
SW1 BAND COVERAGE
Q181 KTC3199 GR GRAPHIC EQUALIZER
2.7V
0.9V
C183 220P
C184 220P
2.7V
0.9V
0.3V
Q182 KTC3199 GR GRAPHIC EQUALIZER
+B
0.3V
R185 220
R186 220
R188
3.9K
C186 1/50
R187
3.9K
R180 560
fH
fL
C185 1/50
C180 100/10
TC5 L7
fH
TC4
MW TRACKING
FM TRACKING
fL
L3
GRAPHIC EQUALIZER PWB-A2
+B
R203
2.2K
R205
4.7K
C201
R201
4.7/50
1K
+B
R200 330
C200 100/10
R202 1K
R206
3.3K
+B
23 21 19 17 15 13 11
6.9V
0V
24 22 20 18 16 14 12 10
C202
C222
4.7/50
4.7/50
R204
2.2K
C203 1/50
C204 1/50
GX-CD1200W
TC1
R259 120
R260 120
fH
L1
fL
fH
7
7
A : 0V B : 0.7V
TC3
fL
L6
5
4 3 2 1
6
LED253
R257 10K
5
4 3 2 1
6
LED254
R258 10K
LED501,502 POWER DIRECTION
LED502
A : 0.8V B : 0.2V
Q505 KTC3199 GR LED CONTROL
0V
FM BAND COVERAGE
LED257
LED255
LED256
LED258
+B
LED259
LED260
fH
R251
6.8K
R255 120
R256 120
R252
6.8K
LED1
STEREO
fL
C251 1/50
C259
0.0039 (ML)
C260
0.0039 (ML)
TC7 L8
C252 1/50
R518 1K
SURRUND
LED401
MW BAND COVERAGE
IC202 LB1403N LEVER METER DRIVER
9
8
C253
0.022
R253 39K
C255 10/16
IC203 LB1403N LEVER METER DRIVER
9
8
C254
0.022
R254 39K
C256 10/16
LED501
R519 1K
R520 10K
R521 10K
TC8
C215
6.5V
0.0015
0.0056
C210
0.082 (ML)
VR204 100K(B) (2KHz)
VR203 100K(A) (500Hz)
C213
0.33/50
(ML)
6.5V
5.9V
(ML)
fH
L5
fL
GRAPHIC EQUALIZER
VR204 100K(A) (2KHz)
C209
0.082 (ML)
C211
0.0015
(ML) C207
9 7 5 3 1
5.9V
6.5V
5.9V
6.5V
5.9V
6.5V
8 6 4 2
C216
0.0056
(ML)
C218
C214
0.47/50
0.33/50
VR202
VR203
50K(B)
100K(B)
(100Hz)
(500Hz)
GRAPHIC EQUALIZER
SW2 BAND COVERAGE
VR205 100K(A) (10KHz)
C205
0.01 (ML)
470P
6.5V
5.9V
5.9V
C220
0.039
(ML)
R208
3.3K
C257 47/25
IC201
BA3822LS
GRAPHIC
EQUALIZER
fH
TC2
SW2 TRACKING
fL
L2
X-BASS
VR202 50K(A) (100Hz)
R207
4.7K
R211 1K
3.2V
3.2V
4.4V
C221 4.7/50
2.6V
4.4V
2.6V
C208
R212 1K
C219
0.039
6.5V
6.5V
470P
C206
0.01 (ML)
VR205 100K(B) (10KHz)
X-BASS
C217
0.47/50
(ML)
5.9V
5.9V
C212
C411
47/10
R417 22K
R418 22K
R415
3.3K
C413
0.001 (ML)
R419
3.3K
R420
3.3K
C414
0.001 (ML)
R416
3.3K
1 2 3 4 5 6 7 8 9
R440 470
VOLUME
C415
0.15
(ML)
C416
0.15
(ML)
CNP103
1 2 3 4 5 6 7 8 9
CNS103
VR401
VR401 50K(B)
VOLUME
50K(B)
R425 1K
R426 1K
R429 100K
R427
4.7K
C418 22/16
R428
4.7K
0.6V
0.6V
Q404 KTC3199 GR POWER MUTE
C510 3300/25
+ – B
A
SW904 TAPE2 DIRECTION
C419
4.7/50
0V
0V
Q403
KTC3199 GR
0V
C420
0V
4.7/50
+B
M501 MOTOR
M
SW901 TAPE1 MAIN
SW902 TAPE2 MAIN
SW903 TAPE2 PLAY
SW401 SURROUND
R441 15K
C423 10/16
POWER MUTE
C424
R442
15K
47/25
1
1
2
2
CNS601
CNP601
TERMINAL B PWB-A6
IC402
LA4663
POWER AMP.
0V
2
L-CH
6
0V
3
14.3V
1
R-CH
0V
4
5
7
6.4V
15V
R431 27K
+B
POWER PWB-A7
C652
0.022
C653
0.022
C425
6.9V
0.1(ML)
+OUT1
14
0V
13
6.9V
-OUT1
12
C427
0.1(ML)
C426
6.9V
0.1(ML)
+OUT2
9
0V
10
6.9V
-OUT2
11
C428
0.1(ML)
8
15V
C433
0.022
D651
TS4B03GM
C651
0.022
C654
0.022
BATTERYS DC 15V ["D" SIZE (UM/SUM-1, R20 or HP2) battery x 10]
R433
2.2
R435
2.2
R434
2.2
R436
2.2
C429 10/16
C430 10/16
F601 T4A L 250V
TERMINAL A PWB-A5
CNP501
SPEAKER
TERMINALS
+
L-CH
– –
R-CH
+
R437 120
R438
J401
120
HEADPHONES JACK
SW601 VOLTAGE SELECTOR
AC110V-127V
AC220V-240V
T601
POWER
TRANSFORMER
SP403 TWEETER
8 Ohm
L-CH
SP401 WOOFER 8 Ohm
SP402 WOOFER 8 Ohm
R-CH
SP404 TWEETER 8 Ohm
SO601 AC SOCKET AC110V-127V/ AC220V-240V, 50/60Hz
+B
+B
R411 330
C505 47/16
0V(0V)
C401
0.0068(ML)
C402
OUT
9V
Q603 KTD2058 Y VOLTAGE REGULATOR
0.7V(0V)
Q503 KTC3199 GR SWITCHING
0.7V (0V)
C511
0.022
C403 10/16
3.8V
R403 10K
R401 100K
C405
0.0033
C406
0.0033
(ML)
R402 100K
R404 10K
3.8V
C404
0.0068(ML)
10/16
3.8V
IC501
3 1
KA7809AP
C506
IN
2
0.022
0V
Q602
0V
KRA102 M SWITCHING
1
7.5V
8.1V
C603
0.022 DZ601
C602
DZ8.2BSB
100/10
9V
C508 100/16
R513
L501
10K
47µH
R514 100K
7.9V (7.9V)
0V(7.9V)
TAPE SPEED
0V(0V)
IC501,502:VOLTAGE REGULATOR
+B
+B
C604 220/10
( ):HIGH SPEED
Q502 KTC3199 GR SWITCHING
0V(0.7V)
R511 10K
R512 10K
3.8V
R405
2.7K
(ML)
R406
2.7K
15V
R602 100
VR102 470
5
6
2
3
OUT
3
C509
0.022
15V 23
IC401 KIA4558P
7.5V
8
OPE AMP.
R407 12K
C407
4.7/50
C408
4.7/50
R408 12K
4
0V
15V
C513 1/50
R601 270
C601
0.022
IC502 KA7809P
2
0V
8.5V(8.5V)
Q504 KTA1271 Y SWITCHING
R516
3.6K
8.5V (6.3V)
R515 120
3.8V
7
R409 12K
R410 12K
3.8V
1
IC401 KIA4558P OPE AMP.
SW501-D FUNCTION SELECTOR
IN
1
15V
R412 10K
R413 10K
C514 1/50
C412 47/10
C409 1/50
C410 1/50
78 9101112
Figure 11 SCHEMATIC DIAGRAM (2/4)
– 11 –
Page 12
GX-CD1200W
9
0
8
7
R
R
M
A
SW810 OPEN/CLOSE
SWITCH PWB-C3
VCC
C3A
LD
2/1VCC
TR+
FO+
FO-
TR-
MON
C2A
C4A
VR1A
B
C
D
PICK-UP UNIT
M
M
+
+
M802 SPINDLE MOTOR
M801
E
SLED MOTOR
SW702 PICKUP IN
CD MOTOR PWB-B
SERIAL NO.
F
PICK-UP UNIT 92LHPC1LASY 92LHPC1LXASY
To serial No.00404990
From serial No.00504991
BI802/CNS802 QCNWN0027BGZZ QCNWN0032BGZZ C801 VCQYKA1HM103K NOT USED R802 VRD-ST2CD222J NOT USED R891 NOT USED VRD-ST2CD683J R892 JUMPER VRD-ST2CD563J R893 JUMPER VRD-ST2CD683J R894 NOT USED VRD-ST2CD683J R895 JUMPER VRD-ST2CD683J R896 JUMPER VRD-ST2CD563J
G
+5V
R-
R+
F+
F-
PD
VR
LD
SP+
PU-IN
GND
B
C
G
SP­SL+ SL-
7 6
E
5
A
4 3
F
2 1
1 2 3 4 5 6 7 8
CNP803
6 5 4 3 2 1
FW802
CNS802
7 6 5 4 3 2 1
CNS801
1 2 3 4 5 6 7 8
CNS803
6 5 4 3 2 1
( ):STOP
Q801 KTA1266 GR SWITCHING
0.2V(1.5V)
C802
3.6V
0.022
R896 56K
R895 68K
R892 56K
R893 68K
R891 68K
R894 68K
(4.4V)
BI802
7 6 5 4 3 2 1
BI801 1
2 3 4 5 6 7 8
BI803 6
5 4
FM-
3
SLT+
2
DM+ DM­FM+
E
A
B
F
C
TR+
TR-
FC+
FC-
GND
PD
VR
LD
1
SLT-
+B
CD SERVO PWB-C1
R802
IC801
2.2K
TA2109F SERVO PRE AMP.
4.3V(5V)
R801 22
C817 100/10
C815 47/10
5V
RFN
VCC
1
GND
IC801
2.1V FNI
2
2.1V
2.1V
2.1V
VG4
12
VG1
10 11
3 4 5 6 7
8 9
FPI
TPI
TNI
MDI
LDO
SEL
TEB
2VRO
TEN
TEO
3.3V
VO4+
VO1+
3.6V
R851
2.2K
C814
0.047
3.3V
VO4-
VO1-
3V
RFO
8
AGCI RFGC
RFGO
RFIS
RFRP
VRO
FEN
FEO
SBAD
TRO
0V0V0V
GND
GND
GND
0V
0V
+B
+B
GND
2.1V
2.1V (2.1V)
2.1V (2.1V)
0.18V (0V)
3.6V (4.4V)
2.5V (0.3V)
2.8V
4.3V
2.1V
R811
22K
C813 47/10
7.4V
2.1V
2.1V
N.C.
30 29 28 27 26 25 24 23 22 21 20
VCC
VIN4
VREF
IC803 LA6541D FOCUS/TRACKING/SPIN/SLED
MT
VIN1
VCC
N.C.
1 2 3 4 5 6 7 8 9
7.4V
2.2V
0.9V
C806
220/10
C805
0.022
C816
0.022
2.1V
24 23
0V
C804
2P(CH)
1.6V (0.3V)
22
0V
21
0V
20
C819
2.2V
19
0.1(ML)
2.1V
18
3.2V (1.1)
17
2.1V
16
15
2.1V
2.1V
R803
82K
14
2.0V
13
(1.1V)
C822
0.047
2
3
FOO
3.3V
3.3V
2.1V
19 18 17 16
VG3
GND
VO3-
VO3+
GND
VG2
VO2+
VO2-
10 11 12 13 14 15
0V
3.4V
3.3V
2.1V
R852
2.2K
R804 68K
R805 39K
R806
2.7K C820
0.1 (ML)
R807 1K
9
C818 56P
C801
0.1
C821
47/10
R853
2.2K
C807
0.047
2.1V
4.8V
N.C.
N.C.
CD
RES
VIN3VIN2
REG IN
REG OUT
5V
2.1V
6.8V (6.8V)
Q802 KTA1271 Y VOLTAGE REGULATOR
FMO DMO
10
5V
6.7V
+B
5V(5V)
C825 47/10
C 4
C832
47/10
+B
C854
C863
0.0068
47/10
C841
0.047
C842
C834 470P
0.047
C837
0.047 ( C838
0.047(M C839
0.047(M
C843
47/10
C835 470P
C836
0.047 (ML)
+B
7.4V(7.5V)
+B
C8 22
+B
H
• NOTES ON SCHEMATIC DIAGRAM can be found on page 18.
1
2
34 5
Figure 12 SCHEMATIC DIAGRAM (3/4)
– 12 –
6
Page 13
GX-CD1200W
+B
863
7/10
841
.047
35
0P 36
47
L)
+B
C825 47/10
C832
C854
0.0068
C834 470P
C837
0.047 (ML) C838
0.047(ML) C839
0.047(ML)
47/10
C842
0.047
C826 47P
C893 220/10
R820 47K
R826 220K
R827 15K
C830
0.01(ML)
C828
0.0027
C829
0.0047
R828 10K
C833
0.033 (ML)
R812 1K
R829 3.3K R830 10K
R831 3.3K R832 3.3K R833 3.3K R834 3.3K
2
XL801
16.93 MHz
C894
0.022 L801
0.82µH
C827
0.015 (ML)
C840
0.047
1
C845
0.047
C860
0.0015
C844 100/10
+B
R840 10
3
R865
+B
+B +B +B
R824 10K
2.1V
50 49 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 32 31
TMAX
2.1V
51
LPFN
2.1V
52
LPFO
2.1V
53
PVREF
1.5V
54
VCOF
0V
55
AVSS
2.1V
56
SLCO
2.1V
57
RFI
5V
58
AVDD
2.1V
59
RFCT
2.1V
60
RFZI
2.7V
61
RFRP
2.3V
62
FEI
2.9V
63
SBAD
2.1V
64
TEI
2.1V
65
TEZI
2.1V
66
FOO
2.1V
67
TRO
2.1V
68
VREF
2.1V
69
RFGC
2.1V
TEBC
70
2.1V
FMO
71
2.1V
72
DMO
4.1V
73
2VREF
2.5V
74
SEL
5V
75
VDD2
0V
76
VSS2
0V
77
XVSS
2.1V
78
XI
2.6V
79
XO
5V
80
XVDD
1K
C853
0.022
DVSR
81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100
0V
+B
C852
3.3/50
C859
0.0027
2.1V
PDO
5 6 1
15
4
17
RO
2.5V
C848
22/16
R836 15K
C850 120P
R858
5.6K
4.2V0V5V
VSS1
P2VREF
12
7
11
14
DVRR
DVDD
2.3V
4.7V
R857
5.6K
2.4V
C849 120P
C823
0.022
5V0V2.5V
1.7V
N.C. N.C. N.C. N.C. N.C. N.C.
SBSY
SBOK
VDD1
DOUT
COFS
13
IC802
TC9457F0
SERVO/SIGNAL
CONTROL
16
LO
DVSL
DVRL
N.C.
N.C.
0V0V0V5V0V
2.5V
C847
22/16
R835 15K
C846
2.2/50
C851
3.3/50
0.4V
2.5V5V0V0V0V0V0V0V0V
N.C.
/HSO
SPDA
SPCK
RESET
HOLD
INTR
N.C. N.C.
5V
5V
R839 47K
C858
0.022
TEST5
MXO
0.3V
TEST4
MXI
TEST3
MVSS
0V
TEST2
MVDD
5V
TEST1
COM1
2.3V
C855
0.022
0V
2
TEST0
0V 5V 0V(5V) 5V 5V 0V 5V 0V 0V 0V 0V 5V 0V 0V 0V 0V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
2.5V
COM2
2.3V
N.C.
CDSEL1 CDSEL0
1
CD LID SW
2.3V
0V
0V
N.C.
PUSEL2
PU IN MUTE ADIN2
ADIN1
P3-0
P1-3
P1-2 P1-1
P1-0 MVSS1 MVDD1
P8-3
SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 SEG2 SEG1
COM4
COM3
2.3V
Q804 KRC102M MUTING
3 0V(5V)
0V
2
+B
L803 10µH
30 29 28 27 26 25 24 23 22 21
20 19 18 17 16 15 14 13 12 11 10
9 8 7 6 5 4 3 2 1
1
N.C. N.C.
N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C. N.C.
N.C.
+B
3
Q803 KRC102M
0V
MUTING
C824
0.1(ML)
0V(5V)
R821 22K
R863
3.3K
R844
3.3K
R861
3.3K R822
22K
L802 10µH
R-CH
GND(A)
L-CH
A-GND
D-GND
R846
FW801
B+
330
SW801
R847
PLAY/
1K
PAUSE
SW802
STOP
8 7 6 5 4 3 2 1
CD CONTROL PWB-C2
CNP804
6 5 4
CNS804
3
FROM MAIN PWB P10 1-D
2 1
R848
2.2K
SW803
REVIEW/
LCD801
TRACK
DOWN
R849
6.8K
SW804
CUE/
TRACK UP
• The numbers 1 to 17 are waveform numbers shown in page 19.
78 9101112
Figure 13 SCHEMATIC DIAGRAM (4/4)
– 13 –
Page 14
GX-CD1200W
R
R
C
0
E C B
3 2 1
C603
R174
R183
IC202
C601
DZ601
Q602
C506
R133
C181
R181
R520
LED501
R257
TO CD SERVO PWB
P17 12-D
CNP804
CNS804
2 3 4 51 6
1
BI804
R602
R601
C602
C604
Q603
E C B
R100
C513
IC501
1
R134
R511
R127
C410
R418
R416
C414
C416
R521
R420
R519
R259
LED255
LED259
LED257
C259
SW101
R518
C251
C136
R404
R255
R253
6
R132
R124
C134
R410
C408
R251
C302
C126
R116
R120
C118
C120
R136
R123
C138
R112
C129
R108
C114
C108
R110
C106
C112
R104
L104
C110
C132
A
B
C133
WH
BK
R408
IC401
4
1
R406
C404
C406
R402
VOLUME PWB-A3
VR401
VOLUME
A
4
C257
C253
R304
R111
C124
R118
R102
FW1
C135
C116
C
5
8
C402
E C B
C122
R106
C104 C102
R405
R409
R403
C401
C307
R114
B
SW102 BEAT CANCEL
C B A
C306
C301
C304
Q301
R306
C303
R305
R302
C113
C127
C128
13
12 10
15
R122
IC101
20
5
R105
C107
1
24
C103
R101
C101
1
2
3
CNP101
DEF
1
2
34
CNP102
C411
R407
R401
1
C403
C407
C409
R412
R415
C413
C415
R419
LED260
L301
R107
R256
R301
R411
C405
C123
C121
R113
C105
C412
C254
LED258
C125
R117
C115
C252
R252
R352 R351
R131
R115
D152
C109
C131
R413
R417
SW4
SURRO
R119
C160
C260
C305
C1
R1
L103
R173
21
R121
CNP501
SPEAKER
R512
FW1
D165
C154
2
BK
D158
R171
D156
1
WH
C222
VR205
C508
C207
TERMINALS
C607
C608
IC502
23 1
L501
C509
CNP103
22334 51
C512
4
B
R184
C
E
C182
1
R182
C180
R186
R188
R130
D163
D164
C159
SW501
FUNCTION SELECTOR
LED502
R203
R205
R206
R204
C204
C203
C221
C205
C202
R202
1 2
Q601
3
C514
7 8 96
C505
C186
C185
C184
B C
Q182
C183
E
Q181
R187
R185
R180
R128
R129
A
B
DC
TAPE
RADIO
CD/LINE
Q505
LED253
2 3 4 51 7 8 96
R201
C255
A
B
C
D
CNS601
FROM POWER PWB P16 5-F
E
F
G
H
MAIN PWB-A1
CNP601
1 2
WH
BK
MIC 151 BUILT-IN MICROPHONE
Q503
R442
C420
C426
R168
1 2 3
C152
R152
J151
C208
R514
C423
C155
E
C
B
C419
D162
R170
7 6
C418
C511
R513
R428 R427
R429
R431
R177
C156
R166
C206
VR204
C209
E C B
R425 R426
D154
C158
R151
C211
Q502
R153
R200
345
R154
C151
C201
CK129
R516
R515
R436
C218
R441
Q153
R438
C213
Q404
IC402
12 14
B C E
JACK
R211
B C E
2 4 6 8 10
R434
VR203
Q504
Q403
1 3
5 7
9 11 13
R165
IC151
C214
C215
B C E
B C E
C157
Q154
R161
MIC JACK
VR102
C510
C424
C433
R433
R435
C427
C425
C428
R169
C430
R437
C429
J401
HEADPHONES
GL
C210 R208
10
VR202
20
C219
24
C217
R207
R212
15
C212 C216 C220
1
5
IC201
C200
1
2
34 5
6
Figure 14 WIRING SIDE OF P.W.BOARD (1/4)
– 14 –
Page 15
R419
102
AT CANCEL
C B A
L301
C123
7
C121
R113
R107
R105
C107
C105
R101
1
01
F
R301
R411
R412
C412
C405
09
R415
C413
C415
R256
C254
LED258
LED260
R352 R351
R131
R119
C125
R117
R115
C160
C115
D152
C109
C131
R413
R417
SW401
SURROUND
C252
R252
C305
WH
BK
R354 R353
C119
C117
Q156
E
R121
C B
R135
C137
R172
R109
C111
R103
L103
R303
R13
R173
R440
ON
OFF
R254
R258
2 3 4 51 7 8 96
IC203
LED401
C260
LED254
LED256
GRAPHIC EQUALIZER PWB-A2
R18
R12
R15
R20
C30
C256
VR1
TP1
C22
C23
R16
R17
C41
R14
TC7
C26
TC5
B
A
MIC
FM MONO
R260
R19
C36
C40
C39
C37
C25
CF1
1 2 3
L6
C21
L8
C28
L7
SW103 DUBBING SPEED/ MIC/FM MODE
NORMAL
LED1
SW501A
C35
13
12
C38
C42
HIGH
FM
TAPE2
MAIN
R7
C34
C32
C33
15 20
L11
C2
2 3 4 51 7 8 96
C5
C6
C20
C19
STEREO
YL YL
R9
IC2
L2
C27
C31
CF3
1 2 3
IC1
R11
E
H
R8
L10
24
510
1
3 2 1
D2
C8
R1
C7
TC2
C4
VC2
VC4 VC3
C16
TC4
C14
R10
SW502
TAPE1
MAIN
C18
C17
C29
C43
C24
CF2
R3
L9
C9
R4
R2
C10
C12
L1
VC1
TC1
VC1
TC3
FW2
F
G
C
B
SW1
BAND SELECTOR
FM MW SW1 SW2
AB
M501
TAPE
MOTOR
C13
TC6
+-
C11
GX-CD1200W
ROD ANTENNA SPRING (249)
COLOR TABLE
BR
ROD ANTENNA (253)
L3
MW
RD(R)
WH(W)
L4
SW1
R5
D1
C15
L5
TC8
L3,4
MW/SW1
BAR ANTENNA
ERASE HERAD
TAPE 1
BROWN
RED
OR
ORANGE
YL
YELLOW
GR
GREEN
BL
BLUE
VL
VIOLET
GY
GRAY
WHITE
BK
BLACK
PK
PINK
RECORD/PLAYBACK
HEAD
RD
BK
WH
FINE TUNING PWB-A4
GY
D
A
SW503 TAPE2
PLAY
BR RD OR YL GR BL VL GR
WH
TC9
CNS103
1 2 3 4 5 6 7 8 9
GR
BA
SW504
TAPE1
DIRECTION
C
RDBK
HEAD FLEXIBLE
B A
WH
TAPE 2
PWB
GY
BK
WH
CNS102
BK
RD
234
1
PLAYBACK HEAD
CNS101
RD
3 2
WH
1
78 9101112
Figure 15 WIRING SIDE OF P.W.BOARD (2/4)
– 15 –
Page 16
GX-CD1200W
A
SW601
VOLTAGE SELECTOR
AC220V-240V AC110V-127V
SO601
AC SOCKET AC110V-127V/ AC220V-240V,
50/60Hz
(250)
TERMINAL A
PWB-A5
(251)
B
OR
BATTERYS
DC15V
["D" SIZE (UM / SUM-1,
R20 or HP2) battery x 10]
C
RD
(251)
T601
POWER
TRANSFORMER
TERMINAL B
PWB-A6
D
BK
BL
RD
WH
(237)
E
WH
OR
COLOR TABLE
BR
OR
YL
GR
BL VL
GY
BK PK
BROWN
RED ORANGE YELLOW
GREEN
BLUE
VIOLET
GRAY WHITE BLACK
PINK
F601
C653
T4A L 250V
BK
C652
C654
C651
D651
F
RD(R)
G
WH(W)
RD
BK
CNS601
1
2
TO MAIN PWB
CNP601
P14 1-D
POWER PWB-A7
H
1
2
34 5
6
Figure 16 WIRING SIDE OF P.W.BOARD (3/4)
– 16 –
Page 17
CD CONTROL PWB-C2
GX-CD1200W
SW802 STOP
SW801 PLAY/ PAUSE
SWITCH PWB-C3
SW810 OPEN/CLOSE
12
FW1
12
12
FW1
1
30
R851
R821
BI803
5
IC803
13
C841
10
R861
C832
C863
R852
2025
C806
R847
10
10
R846
C805
R863
C826
15
16
C807
R822
R844
C825
R849
FW801
C823
R820
C894
C824
R824
R826
R853
R848
L802
FW801
30
31
R827
C893
SW804 REVIEW/ TRACK DOWN
1
20
25
35
40
45
C827
B C E
Q802
1
15
50
1
10
IC802
55
C830
5
60
100
51
C834
C802
16
95
70
65
C828
C838
C835
Q801
R801
1
C851
C852
C801
R812
SW803 CUE/ TRACK UP
1
2
2
3
6 5 4 3 2
CNP804
1
7
BI802
1
3
R858
1
R802
Q803
Q804
11
1
CNS804
FROM MAIN PWB P14 5-A
9
WH
7
WH
6
WH
5
WH
4
WH
3
WH
2
BK
1
10
LCD801
2345 178 6
15
14
4
17
C846
C855
C847
R839
90
85
75
C836
E
C817
C B
BI801
81
80
R805
C804
C816
R829
R806
X801
R830
C815
R865
C839 C820
R804
8
R832
R833
24
1
C843
R834
R807
IC801
5
R891
R895
CD SERVO PWB-C1
C853
C848
C844
C819
20
R835
C845
R831
R894
L803
C837
C854 C829
R803
15
10
R896
R836
R840
C840
13
12
C849
C818
C813
R892
C850
C858
R828
C833
R893
R857
L801
C842
C822
R811
C821
C814
BRBKBKBKBKBKBK
3
2
5
6
7
2 3 4 51 7 86
CNS801
CD MOTOR PWB-B
+
M801 SLED MOTOR
-
CNS803 BR GY GY GY GY GY
CNP803
1 2 3 4 5 6
• The numbers 1 to 17 are waveform numbers shown in page 19.
78 9101112
1 2 3 4 5 6
F0027AW
SW702 PICKUP IN
M802 SPINDLE MOTOR
+
-
PICK-UP UNIT 92LHPC1LASY 92LHPC1LXASY BI802/CNS802 QCNWN0027BGZZ QCNWN0032BGZZ C801 VCQYKA1HM103K NOT USED R802 VRD-ST2CD222J NOT USED R891 NOT USED VRD-ST2CD683J R892 JUMPER VRD-ST2CD563J R893 JUMPER VRD-ST2CD683J R894 NOT USED VRD-ST2CD683J R895 JUMPER VRD-ST2CD683J R896 JUMPER VRD-ST2CD563J
Figure 17 WIRING SIDE OF P.W.BOARD (4/4)
– 17 –
BK
8
WH(W)
SERIAL NO.
COLOR TABLE
BROWN
BR
RED
RD(R)
ORANGE
OR
YELLOW
YL
GREEN
GR
BLUE
BL
VIOLET
VL
GRAY
GY
WHITE BLACK
BK
PINK
PK
To serial No.00404990
PICK UP UNIT
5476 321
78 654321
From serial No.00504991
Page 18
GX-CD1200W
NOTES ON SCHEMATIC DIAGRAM
• Resistor: To differentiate the units of resistors, The symbol as K and M are used: the symbol K means 1000 ohm and the symbol M means 1000 kohm and the resistor without any symbol is an ohm resistor. The resistor designated “Fusible” is a fuse type resistor.
• Capacitor: To indicate the unit of capacitor, a symbol P is used: this symbol P means pico-farad and the unit of the capacitor without such a symbol is microfarad. As to electrolytic capacitor, the expression “capacitance/withstand voltage” is used. (CH),(RH),(UJ): Temperature compensation (ML): Mylar type (S): Styrol type
• The indicated voltage in each section is the one measured by Digital Multimeter between such a section and the chassis with no signal given.
• Schematic diagram and Wiring Side of P.W. Board for this model are subject to change for improvement without prior notice.
• Parts marked with “ ” ( ) are important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
REF. NO.
DESCRIPTION POSITION
SW1 BAND SELECTOR FM SW101 RECORD/PLAYBACK PLAYBACK SW102 BEAT CANCEL A SW103 DUBBING SPEED/MIC/ MIC/FM MONO
FM MODE SW401 SURROUND ON SW501 FUNCTION SELECTOR CD/LINE SW601 VOLTAGE SELECTOR AC220-240V SW702 PICKUP IN OFF SW902 TAPE 2 MAIN OFF SW901 TAPE 1 MAIN OFF SW903 TAPE 2 PLAY OFF SW904 TAPE 2 DIRECTION A
FRONT
VIEW
FRONT
VIEW
IC2 (LA1805)
PIN FM MW/SW
PIN FM MW/SW
123456789101112
1.6V
1.6V
1.6V
1.6V
13 14 15 16 17 18 19 20 21 22 23 24
2.2V
1V 0V
1.8V1V1.5V
IC101 (TA8189N)
PIN PLAY REC
123456789101112
0V0V0V0V1.3V
VOL T AGE
7.2V8V0.5V
0.8V
1.7V
1.7V
1.4V
1.3V
1.4V
KTD2058 Y
1.6V
1.6V0V0V
1.6V
1.6V
1.7V
1.6V
1.4V
1.3V
1.4V
1.3V0V0V0V0V
E C B
E C B
KTA1266 GR
333ID213 KTA1271 Y KTC3199 GR KTC3203 Y KRA102 M
Figure 18 TYPES OF TRANSISTOR AND LED
7.6V
7.6V0V0V
0.4V
0.7V
2.3V
2.3V
2.4V
2.4V
7.2V8V7.2V8V0.5V
1.6V
1.8V
1.3V
1.8V
1.3V0V0V0V0V
6.5V8V0.9V
0.9V
1.6V
1.4V
1.6V
1.6V
PIN PLAY REC
13 14 15 16 17 18 19 20 21 22 23 24
0.9V
0.9V0V0V
1.3V
1.3V
IC202/203 (LB1403N)
PIN LED OFF LED ON
123456789
7.7V1V7.7V1V7.7V1V7.7V1V0V0V7.7V1V0V
1.8V
1.8V
1.4V
1.4V
– 18 –
7.4V
7.4V
1.4V0V1.4V
1.4V
2.4V0V0V
1.4V
1.3V
1.4V
1.3V0V0V0V0V
8.6V
8.6V
Page 19
WAVEFORMS OF CD CIRCUIT
NO DISC FOCUS SEARCH STOP PLAY
GX-CD1200W
1
IC802 66pin
IC803 20pin
IC803 21pin
IC802 74pin
IC802 62pin
IC802 64pin IC802 71pin
IC802 62pin
IC802 63pin
FOO
FO+ 2
2 3
FO- 3 DMO 3
FOCUS SEARCH TOC IL STOP PLAY
4
SEL 1 TEI 1
5
FEI 2 TRO 2
TEI 3 FMO 3
6
STOP PLAY CUE
5
FEI
SBAD 2 TRO 2
7
1 TMAX 1
1 TEI 1
12
IC802 50pin
13
IC802 45pin
14
IC802 72pin
6
IC802 64pin
11
IC802 67pin
15
6
IC802 64pin
11
IC802 67pin
SBOK
2
RFO 3 FMO 3
8
IC801 22pin
STOP PLAY REVIEW
5
FEI
IC802 62pin
RFGO 2 TRO 2
9
IC801 19pin IC802 67pin
RFRP 3
10
IC801 17pin
STOP PLAY TCD-782 TNO-02 PLAYBACK
TEI 1LO 1
6
IC802 64pin
TRO 2
11
IC802 67pin
SBAD 3
7
IC802 63pin
1 TEI 1
15
IC802 71pin
6
IC802 64pin
11 15
IC802 71pin
16
IC802 86pin
17
IC802 82pin
FMO
RO 2
3
– 19 –
Page 20
GX-CD1200W
TROUBLESHOOTING (CD SECTION)
When the CD does not function
When the CD section does not operate when the objective lens of the optical pickup is dirty, this section may not operate. Clean the objective lens, and check the playback operation. When this section does not operate even after the above step is taken, check the following items. Remove the cabinet and follow the troubleshooting instructions. "Track skipping and/or no TOC (Table Of Contents) may be caused by build up of dust other foreign matter on the laser pickup lens. Before attempting any adjustment make certain that the lens is clean. If not, clean it as mentioned below."
Turn the power off. Gently clean the lens with a lens cleaning tissue and a small amount of isopropyl alcohol. Do not touch the lens with the bare hand.
Dust gradually accumulates on the objective lens during use, and it may degrade performance. To avoid this problem, use a cleaning disc designed for CD optical pickup lenses.
HOW TO USE
1. Using the brush in the cleaner cap, apply 1 or 2 drops of the cleaning fluid to the brush on the CD cleaner disc which has the mark next to it.
2. Place the CD cleaner disc onto the CD disc tray with the brush side down, then press the play button.
3. You will hear music for about 20 seconds and the CD player will automatically stop. If it continues to turn, press the stop button.
CAUTION
The CD lens cleaner should be effective for 30 - 50 operations, however if the brushes become worn out earlier then please replace the cleaner disc. If the CD cleaner brushes become very wet then wipe off any excess fluid with a soft cloth. Do not drink the cleaner fluid or allow it to come in contact with the eyes. In the event of this happening then drink and / or rinse with clean water and seek medical advice. The CD cleaner disc must not be used on car CD player or on computer CD-ROM drives. All rights reserved. Unauthorized duplicating, broadcasting and renting product is prohibited by law.
Cleaning Liquid
• The CD function will not work.
The CD operating keys don't work.
Check the power supply, 16.93 MHz clock, and reset terminal.
Check the pickup-in switch (SW702) position.
Check the Focus system.
Cleaning Disc PARTS CODE: UDSKA0004AFZZ
– 20 –
Page 21
• Laser failure.
GX-CD1200W
Is +7.5V applied to the emiter of Q802 ?
Yes
Is +5V applied to the collector of Q802 ?
Yes
Is +5V applied to the pin 75 (VDD) of IC802 ?
Yes
Is +5V applied to the pin 1 (VCC) of IC801 ?
Yes
Is +0V applied to the pin 74 (SEL) of IC802 ?
Yes
Is approx. 1.8V applied to the collector of Q801.
Yes
Check BI801/CNS801. If it is normal, the optical pickup is faulty.
No
No
No
No
No
No
Check the PWB pattern of Q603.
Check the peripheral parts of IC803 and Q802.
Check the PWB pattern between collector of Q204 and pin 75 of IC802.
Check the PWB pattern between collector of Q204 and pin 1 of IC801.
Check the laser come on when pattern cut between pin 8 (SEL) of IC801 and pin 74 (SEL) of IC802.
Check the peripheral parts of IC801 and Q801. If it is normal, the optical pickup is faulty.
• Focus failure.
Does the optical pickup move up and down when the disc is removed?
Yes
Is the following waveform ouput at the pin 62 (FEI) of IC802 when the disc is set?
Yes
pin 62 (FEI)
pin 86 (FOO)
pin 63 (SBAD)
Is the waveform shown above input at the pin 63 (SBAD) of IC802?
Yes
IC801 is faulty.
No
No
No
Check as stated in item "FOCUS SERVO SAWTOOTH WAVE FAILURE".
Check the periphery of IC801 and BI801/CNS801. Is it normal?
Yes
The optical pickup is faulty.
Check the pattern between pin 13 of IC801 and pin 63 of IC802. Check the periphery of IC801 and BI801/CNS801.
– 21 –
Page 22
GX-CD1200W
• Focus servo sawtooth wave failure.
Is sawtooh wave output to the pin 66 (FOO) of IC802 ?
Yes
1.5~2.5sec
Is +8.1V applied to the pins 1 and 30 (VCC) of IC803 ?
Yes
Is sawtooth wave obtained between pins 20 and 21 of IC803 ?
Yes
1.5~2.5sec
Is sawtooth wave obtained between pins 3 and 4 of BI801/ CNS801 ? (as shown above)
Yes
BI801/CNS801 connection failure or optical pickup failure.
No
No
No
No
IC802 is faulty.
Check the PWB pattern of IC803.
Check the PWB pattern of IC803.
Check the PWB pattern between BI801/CNS801 and IC803.
• Spindle motor clv servo failure.
Is following wave output to the pin 55 (AVSS) of IC802 when the Function is changed to "PLAY" from "STOP" ?
Yes
DMO
Is above wave obtained between pins 5 and 6 of IC803 ?
Yes
Is above wave obtained between pins 5 and 6 of BI803/ CNS803 ?
Yes
BI803/CNS803 connection failure or optical pickup failure.
No
No
No
Check the procedure in "HF ERROR". If OK. IC802 is faulty.
Check the PWB pattern between pin 72 (DMO) of IC802 and pins 5 and 6 of IC803. If OK. IC803 is faulty.
Check the PWB pattern between BI803/CNS803 and IC803.
– 22 –
Page 23
• Track search failure
GX-CD1200W
Does the sled motor run in FF/REW state when the CD TEST MODE is set?
Yes
Is the following wave output to the pin 67 (TRO) of IC802 during track search in normal playback?
Yes
TRO
Is the following wave output to the pins 12 (TEO) of IC801 during track search in normal playback?
Yes
TEO
TEI
TEZI
Is the above wave output to the pins 64 (TEI) and 65 (TEZI) of IC802 during track serch in normal playback?
Yes
Is the following wave output to the pin 60 (RFZI) and 61 (RFRP) of IC802 during track search in normal playback?
Yes
RFRP
RFZI
No
No
No
No
No
Check as stated in item "SLED MOTOR OPERATION FAILURE".
IC802 failure.
Check the PWB pattern between pin 67 (TRO) of IC802 and pin 28 of IC803. Check the PWB pattern between pins 25 and 26 of IC803 and Optical pickup. If OK. Optical pickup failure.
Check the PWB pattern between pin 12 (TEO) of IC801 and pins 64 (TEI) and 65 (TEZI) of IC802. If OK. IC801 failure.
Check the PWB pattern between pin 22 (RFO) and 18 (RFIS), 17 (RFRP) of IC801 and pins 60 and 61 of IC802. If OK. IC801 failure.
Normal.
• Sled motor operation failure.
Is following sled feed signal output the pin 71 (FMO) of IC802 when FF/REW key is pressed after the CD TEST MODE is sated?
Yes
Is following sled feed signal input the pins 12 and 13 of IC803 when FF/REW key is pressed after the CD TEST MODE is seted?
Yes
Is sled feed signal output the pins 10 and 11 of IC803?
Yes
Is sled feed voltage applied between both terminals of sled motor?
Yes
Check the CD mechanism (periphery of sled motor). If the sled motor does not run when DC2.0V is applied to both terminals of sled motor, the sled motor is faulty.
FF REW
FMO
FF REW
SL ±
No
No
No
No
IC802 is faulty.
Check the PWB pattern between pin 71 of IC802 and pins 12 and 13 of IC803.
Check the peripheral parts of IC803. If OK, IC803 is faulty.
Check the BI803/CNS803.
• Sled servo failure.
Is following sled signal output the pin 71 (FMO) of IC802 during playback?
Yes
FMO
Normal.
No
IC802 is faulty.
– 23 –
Page 24
GX-CD1200W
FUNCTION TABLE OF IC
IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (1/4)
Pin No.
1* (OT5)S1 SEG1 Output Segment signal output to the LCD panel. 2 (OT6)S2 SEG2 Output Up to 72 segments in a matrix with COM1 to COM4 can be displayed. 3 (OT7)S3 SEG3 Output All of the S1 to S18 pins can be switched for output ports by a program. 4 (OT8)S4 SEG4 Output Also, the S15 to S18 pins each can be switched for I/O ports individually. 5 (OT9)S5 SEG5 Output When set for I/O ports, these pins become Nch open-drain output. 6* (OT10)S6 SEG6 Output Furthermore, the S11 to S14 and the P8-0 to P8-3 pins can be switched for 7* (OT11)S7 SEG7 Output use as CD signal (CLCK to IPF) input/output pins by a program. 8* (OT12)S8 SEG8 Output • CLCK: Subcodes P thru W data readout clock input/output. 9* (OT13)S9 SEG9 Output Selected between input and output by a command. 10* (OT14)S10 SEG10 Output • DATA: Subcodes P thru W data output. 11*
12*
13*
14*
15 (BCK/S15) CDSEL0 Output • IPF : Correction flag output. When AOUT is C2 correction output, it
16 (AOUT/S16) CDSEL1 Output
17 (MBOV/S17) CD LID SW Output
18 (IPF/S18) DOOR OUT Output
19 MVDD MVDD1 Power supply pins. 20 MVSS MVSS1 Normally, apply a voltage of 4.5 to 5.5V to VDD.
21* (K0)P1-0 TRAY CLOSE Input 4-bit CMOS I/O ports. 22* (K1)P1-1 TRAY OPEN Input These ports can be set for input or output bit for bit by a program. 23 (K2)P1-2 PUSEL0 Input These pins can be pulled up to VDD or down to GND by program. 24 (K3)P1-3 PUSEL1 Input Therefore, they can be used as key input pins. Also, when they are set for
25 26 (ADin1)P3-1 ADIN1 Input These ports can be set for input or output bit for bit by a program. 27 (ADin2)P3-2 ADIN2 Input The P3-0 to P4-0 pins serve dual purposes as analog inputs for the internal 28 (ADin3)P3-3 MUTE Input 6-bit 4-channel A/D converters. 29 (BUZR/ PU IN Input The internal A/D converters can complete conversion in 6 instruction cycles
Port Name
(CLCK/OT15) S11 • LRCK: Channel clock (44.1kHz) output. (DATA/OT16) S12 Polarity can be inverted by a command. (SFSY/OT17) S13 • AOUT: Audio data output. (LRCK/OT18) S14 It outputs a high when buffer overflows.
P8-0 outputs a high indicating that correction is impossible.
P8-1
P8-2
P8-3
(DCREF)P3-0
ADin4)P4-0 using a successive approximation method. The required pins can be set for
Terminal Name
SEG11 Output • SFSY: Playback system frame sync signal output.
SEG12 Output It outputs a low for L channel and a high for R channel.
SEG13 Output • BCK : Bit clock (1.4122MHz) output.
SEG14 Output • MBOV: Buffer memory-over signal output.
DISPLAY Input 5-bit CMOS I/O ports.
Input/Output
Function
In a backup state (when the CKSTP instruction executed), the device's current consumption is reduced to 1µA or less, allowing for the supply voltage to be lowered to 2.0V. The device is reset and the program starts from address 0 when a voltage of 2.7V or more is applied to this pin when it is at 0V (power-on reset).
I/O port, a change of state in this input can be used to clear the clock stop or wait mode.
A/D analog input bit for bit by a program. P3-0 can be set for reference voltage input, and the internal power supply (MVDD) can be used for this reference voltage. The P4-0 pin serves dual purposes as a buzzer output pin. The buzzer output can be selected from 8 frequencies, 0.625 to 3kHz. Each selected frequency can be output in one of four modes: continuous, single, 10Hz intermittent, and 10Hz intermittent at 1Hz interval. Whether or not to use and how to control the A/D converter and buzzer all can be set by a program.
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.
– 24 –
Page 25
IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (2/4)
GX-CD1200W
Port Name Terminal NamePin No. Input/Output
30 (S12)P4-1 PUSEL2 Input 3-bit CMOS I/O ports. 31* (SO/S11/ NC Input/Output These ports can be set for input or output bit for bit by a program.
SDA)P4-2 These pins serve dual purposes as input or output pins for the serial
32* (SCK/SCL) NC Input/Output interface circuit (SIO).
P4-3 The SIO is a 2-wire/3-wire compatible serial interface. 4 or 8 bits of serial
data, beginning with the MSB or LSB, are serially output from the SO/SDA, pin at each clock edge on the SCK/SCL pin, and the data on S11 or S12 pin is serially input to the device. The serial clock (SCK/SCL) allows selection between the internal (450/225/ 150/75 kHz) and external sources and a selection of the active edge, rise or fall. Moreover, since the clock and data can be output via Nch open-drain outputs, various, device controls and communication between controllers can be greatly facilitated. When an SIO interrupt is enabled, an interrupt is generated at completion of SIO execution and the program jumps to address 4. All inputs to SIO contain a Schmitt trigger circuit.
33 TEST0 TEST0 Input Test mode control input pins. 34 TEST1 TEST1 Input The test mode is selected when these pins are set high and normal 35 TEST2 TEST2 Input operation is selected when they are low. 36 TEST3 TEST3 Input 37 TEST4 TEST4 Input 38 TEST5 TEST5 Input
39* (OT19)/HSO /HSO Output CD control output pins. 40* (OT20)SPCK SPCK Output • /HSO: Playback speed mode output. 41* (OT21)SPDA SPDA Output High = normal speed; Low = double speed. 42* (OT22)COFS COFS Output • SPCK: Processor status signal readout clock output (176.4kHz)
• SPDA: Processor status signal output.
• COFS: Correction system frame clock output (7.35kHz)
These pins can be switched for output ports by a program. 43* DOUT DOUT Input/Output Digital output pin. 44* SBSY SBSY Input/Output Subcode block sync output pin. It outputs a high at the S1 position when
subcode sync is detected. 45* SBOK SBOK Input/Output Subcode Q data CRCC determination result output pin. It outputs a high
when CRCC check is found OK. 46 VDD VDD1 Input/Output CD unit's digital block power supply pins.
47 VSS VSS1 Input/Output Normally, apply 5V to VDD.
When not using a CD (CD off), this power supply can be turned off, with
only the controller power supply kept active, so that the controller alone is
operating. In this case, the CD off bit must be set to 1. When this bit is set
to 1, pins 11 through 18 and pins 39 through 42 all are changed for output
ports if they have been set for CD control signal input/output pins. 48 P2VREF P2VREF Input/Output PLL block-2 VREF pin. 49 PDO PDO Input/Output This pin outputs a phase error between EFM and PLCK signals. 50 TMAX TMAX Input/Output TMAX detection result output pin.
Selected by command bit TMPS.
Longer than preset period: Outputs P2VREF.
Shorter than preset period: Low level (Vss).
Within preset period: High impedance. 51 LPFN LPFN Input/Output Inverted input of low-pass filter amp. 52 LPFO LPFO Input/Output Output of low-pass filter amp. 53 PVREF PVREF Input/Output PLL block VREF pin. 54 VCOF VCOF Input/Output VCO filter pin. 55 AVSS AVSS Input/Output Analog block ground pin. 56 SLCO SLCO Input/Output DAC output pin for data slice level generation. 57 RFI RFI Input/Output RF signal input pin. 58 AVDD AVDD Input/Output Analog block power supply pin. 59 RFCT RFCT Input/Output RFRP signal center level input pin. 60 RFZI RFZI Input/Output RFRP zero-cross input pin. 61 RFRP RFRP Input/Output RF ripple signal input pin. 62 FEI FEI Input/Output Focus error signal input pin.
Function
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.
– 25 –
Page 26
GX-CD1200W
IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (3/4)
Port Name Terminal NamePin No. Input/Output
63 SBAD SBAD Input/Output Subbeam add signal input pin. 64 TEI TEI Input/Output Tracking error input pin.
This input is read when tracking servo is on. 65 TEZI TEZI Input/Output Tracking error zero-cross input pin. 66 FOO FOO Input/Output Focus equalizer output pin. 67 TRO TRO Input/Output Tracking equalizer output pin. 68 VREF VREF Input/Output Analog reference power supply pin. 69 RFGC RFGC Input/Output RF amplitude adjusting control signal output pin. It outputs 3-level PWM
signals. (PWM carrier = 88.2kHz) 70 TEBC TEBC Input/Output Tracking balance control signal output pin. It outputs 3-level PWM signals.
(PWM carrier = 88.2kHz) 71 FMO FMO Input/Output Focus equalizer output pin. It outputs 3-level PWM signals.
(PWM carrier = 88.2kHz) 72 DMO DMO Input/Output Disc equalizer output pin. It outputs 3-level PWM signals.
(PWM carrier = DSP block 88.2kHz, synchronized to PXO) 73 2VREF 2VREF Input/Output Analog reference power supply pin. (2 x VREF) 74 SEL SEL Input/Output APC circuit on/off signal output pin.
When laser is on, this pin goes to a high-impedance state when UHS = low
and outputs a high when UHS = high 75 VDD VDD2 Input/Output CD unit's digital block power supply pins.
76 VDD VSS2 Input/Output Normally, apply 5V to VDD.
When not using a CD (CD off), this power supply can be turned off, with
only the controller power supply kept active, so that the controller alone is
operating. In this case, the CD off bit must be set to 1. When this bit is set
to 1, pins 11 through 18 and pins 39 through 42 all are changed for output
ports if they have been set for CD control signal input/output pins. 77 XVSS XVSS Input/Output CD's crystal oscillator power supply pins.
Normally, connect these pins to the power supply lines that are used in
common for the VDD and VSS pins. 78 XI XI Input/Output CD's crystal oscillator input/output pins.
79 XO XO Input/Output Normally, connect 16.934MHz here. This clock is used as the system clock
for the CD. After a system reset, it also is used as the system clock on the
controller side. 80 XVDD XVDD Input/Output CD's crystal oscillator input/output pins.
Normally, connect these pins to the power supply lines that are used in
common for the VDD and VSS pins. 81 DVSR DVSR Input/Output R-channel D/A converter unit ground pin. 82 RO RO Input/Output R-channel data forward output pin. 83 DVRR DVRR Input/Output R-channel reference voltage pin. 84 DVDD DVDD Input/Output D/A converter unit power supply pin. 85 DVRL DVRL Input/Output L-channel reference voltage pin. 86 LO LO Input/Output L-channel data forward output pin. 87 DVSL DVSL Input/Output L-channel D/A converter unit ground pin. 88 NC NC Input/Output NC pins. Normally, connect these pins to ground or leave them open.
89* NC/VPP NC Input/Output 90 /RST RESET Input Device's system reset signal input pin.
The device remains reset while RESET is held low and when RESET is
released back high, the CD unit becomes operational and the program
starts from address 0. Normally, a system reset is asserted when a voltage
of 2.7V or more is applied to VDD when it is at 0V (power-on reset).
Therefore, this pin must be pulled high when used for this purpose.
Function
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.
– 26 –
Page 27
IC802 VHiTC9457F0-1: Servo/Signal Control (TC9457F0) (4/4)
GX-CD1200W
Pin No.
91 /HOLD HOLD Input This pin is used to input a signal that requests or clears the hold mode.
92 INTR REMO-IN Input External interrupt input pin.
93* MXO MXO Crystal oscillator pins for the controller. 94* MXI MXI The oscillator clock is used as the timebase for the clock facility or as the
95 MVSS MVSS Power supply pins. 96 MVDD MVDD Normally, apply a voltage of 4.5 to 5.5V to VDD.
97 OT1 COM1 Output Common signal outputs to the LCD panel. 98 OT2 COM2 Output Up to 72 segments in a matrix with S1 to S18 can be displayed. 99 OT3 COM3 Output Three voltage levels MVDD, VEE (1/2 MVDD), and GND are output for 100 OT4 COM4 Output 83Hz period at 2ms intervals.
Port Name
Terminal Name
Input/Output
Function
Normally, use this pin for CD mode select signal input or battery detection signal input. There are two hold modes: clock stop mode (crystal oscillator turned off) and a wait mode (CPU stopped). These modes are entered by executing the CKSTP and WAIT instructions, respectively. The clock stop mode can be requested by a programmed input: low level detection on HOLD pin or forced execution, and can be cleared by detecting a high on the HOLD pin or a change of state in its input signal. When the CKSTP instruction is executed, the clock generator and the CPU stop operating and the device is placed in a memory backup state. During this state, the device's current consumption is reduced to 1µA or less. At the same time, the display output and CMOS output ports are automatically set low, and the Nch open-drain outputs are turned off. The wait mode is executed regardles of the input state on the HOLD pin, with the device's current consumption reduced. This mode is cleared by a change of state in the HOLD input.
When the interrupt facility is enabled and a pulse of 1.11 to 2.22µs in duration is applied to this pin, an interrupt is generated and the program jumps to address 1. Input logic and the active edge (rise or fall) can be selected for each interrupt input. Also, the internal 8-bit time clock can be chosen for this interrupt input, in which case it is possible to count pulses or generate an interrupt at a given pulse count (address 3).
controller's system clock. Connect a 4.5MHz or 75kHz crystal resonator to the MXO and MXI pins. Since these pins do not contain internal feedback resistors, etc, an amp resistor or output resistor must be added external to the chip. When using the clock generated by the CD unit's crystal oscillator for clocking the entire device operation, fix the MXI pin to the GND level. Oscillation is stopped by executing a CKSTP instruction. Select the crystal oscillator and control its operation by a program.
In a backup state (when the CKSTP instruction executed), the device's current consumption is reduced to 1µA or less, allowing for the supply voltage to be lowered to 2.0V. The device is reset and the program starts from address 0 when a voltage of 2.7V or more is applied to this pin when it is at 0V (power-on reset).
After a system reset and after deassertion of a clock stop instruction, the VEE voltage is output and the DISP OFF bit is set to 0 before common signals are output.
In this unit, the terminal with asterisk mark (*) is open terminal which is not connected to the outside.
To serial No.006XXXXX
TC9457F-013 JAPAN
From serial No.007XXXXX
TC7457F-022 JAPAN
– 27 –
Page 28
GX-CD1200W
— M E M O —
– 28 –
Page 29
PARTS GUIDE
MODEL GX-CD1200W(GL)
“HOW TO ORDER REPLACEMENT PARTS”
To have your order filled promptly and correctly, please furnish the following information.
1. MODEL NUMBER 2. REF. No.
3. PART NO. 4. DESCRIPTION
MARK: SPARE PARTS-DELIVERY SECTION
GX-CD1200W
PORTABLE CD STEREO
COMPONENT SYSTEM
GX-CD1200W(BK)
For U.S.A. only
Contact your nearest SHARP Parts Distributor to order.
For location of SHARP Parts Distributor, Please call Toll-Free; 1-800-BE-SHARP
Explanation of capacitors/resistors parts codes
Capacitors
VCC ....................... Ceramic type
VCK........................ Ceramic type
VCT........................ Semiconductor type
VC • • MF ............... Cylindrical type (without lead wire)
VC • • MN............... Cylindrical type (without lead wire)
VC • • TV................ Square type (without lead wire)
VC • • TQ ............... Square type (without lead wire)
VC • • CY ............... Square type (without lead wire)
VC • • CZ ............... Square type (without lead wire)
VC • • • • • • • • • J .. The 13th character represents capacity difference.
("J" ±5%, "K" ±10%, "M" ±20%, "N" ±30%, "C" ±0.25 pF, "D" ±0.5 pF, "Z" +80-20%.)
If there are no indications for the electrolytic capacitors, error is ±20%.
Resistors
VRD ....................... Carbon-film type
VRS........................ Carbon-film type
VRN ....................... Metal-film type
VR • • MF ............... Cylindrical type (without lead wire)
VR • • MN............... Cylindrical type (without lead wire)
VR • • TV................ Square type (without lead wire)
VR • • TQ ............... Square type (without lead wire)
VR • • CY ............... Square type (without lead wire)
VR • • CZ ............... Square type (without lead wire)
VR • • • • • • • • • J .. The 13th character represents error.
("J" ±5%, "F" ±1%, "D" ±0.5%.)
If there are no indications for other parts, the resistors are ±5% carbon-film type.
NOTE:
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace parts with specified ones for maintaining the safety and performance of the set.
– 29 –
Page 30
GX-CD1200W
PARTS CODE NO. PARTS CODE
PRICE
RANK
DESCRIPTIONNO.
INTEGRATED CIRCUITS
IC1 VHITA7358AP-1 J AG FM Front End,TA7358AP IC2 VHILA1805//-1 J AM FM/AM IF MPX.,LA1805 IC101 VHITA8189N/-1 J AM Record/Playback Amp.,TA8189N IC151 VHITA2011S/-1 J AM Mic Amp.,TA2011S IC201 VHIBA3822LS-1 J AL Graphic Equalizer,BA3822LS IC202,203 VHILB1403N/-1 J AG Level Meter Driver,LB1403N IC401 VHIKIA4558P-1 J AC Ope Amp.,KIA4558P IC402 VHILA4663//-1 J AQ Power Amp.,LA4663 IC501,502 VHIKA7809AP-1 J Voltage Regulator,KA7809AP IC801 VHITA2109F/-1 J AL Servo Pre Amp.,TA2109F IC802 VHITC9457F0-1 J AZ Servo/Signal Control,TC9457F0 IC803 VHILA6541D/-1 J AW Focus/Tracking/Spin/Sled Driver,
LA6541D
TRANSISTORS
Q153 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q154 VSKRA102M//-1 J AC Digital,PNP,KRA102 M Q156 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q181,182 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q301 VSKTC3203Y/-1 J AC Silicon,NPN,KTC3203 Y Q403,404 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q502,503 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q504 VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y Q505 VSKTC3199GR-1 J AB Silicon,NPN,KTC3199 GR Q601 VSKRC102M//-1 J AC Digital,NPN,KRC102 M Q602 VSKRA102M//-1 J AC Digital,PNP,KRA102 M Q603 VSKTD2058Y/-1 J AF Silicon,NPN,KTD2058 Y Q801 VSKTA1266GR-1 J AB Silicon,PNP,KTA1266 GR Q802 VSKTA1271Y/-1 J AC Silicon,PNP,KTA1271 Y Q803,804 VSKRC102M//-1 J AC Digital,NPN,KRC102 M
DIODES
D1,2 VHDDS1SS133-1 J AB Silicon,DS1SS133 D152 VHDDS1SS133-1 J AB Silicon,DS1SS133 D154 VHDDS1SS133-1 J AB Silicon,DS1SS133 D156 VHDDS1SS133-1 J AB Silicon,DS1SS133 D158 VHDDS1SS133-1 J AB Silicon,DS1SS133 D162~165 VHDDS1SS133-1 J AB Silicon,DS1SS133
! D651 VHDTS4B03GM-1 J AK Silicon,TS4B03GM
DZ601 VHEDZ8R2BSB-1 J AB Zener,8.2V,DZ8.2BSB LED1 VHP333ID213-1 J LED,RED,333ID213 LED253~260 VHP333ID213-1 J LED,RED,333ID213 LED401 VHP333ID213-1 J LED,RED,333ID213 LED501,502 VHP333ID213-1 J LED,RED,333ID213
FILTERS
CF1 RFILR0008AWZZ J AE FM Band Pass Filter CF2 92LFILTF1342A J AD FM IF,10.7 MHz CF3 RFILA0001BGZZ J AC AM IF,455 kHz
TRANSFORMER
! T601 RTRNP0001BGZZ J AX Power
COILS
L1 RCILB0001BGZZ J AD FM Oscillation L2 RCILR0001BGZZ J AA FM Tracking L3,4 RCILA0001BGZZ J AH MW/SW1 Bar Antenna L5 RCILA0003BGZZ J AC SW2 Antenna L6 RCILB0002BGZZ J AC MW Oscillation L7 RCILB0003BGZZ J AC SW1 Oscillation L8 RCILB0004BGZZ J AC SW2 Oscillation L9 RCILI0002BGZZ J AD FM IF L10 RCILI0003BGZZ J AD FM Detection L11 RCILI0001BGZZ J AD AM IF L103,104 VP-MK223K0000 J AC 22 mH,Choke L301 RCILB0005BGZZ J AD Bias Oscillation L501 VP-MK470K0000 J AB 47 µH,Choke L801 VP-DHR82K0000 J AE 0.82 µH,Choke L802,803 VP-DH100K0000 J AB 10 µH,Choke
VARIABLE RESISTORS
VR1 RVR-M0026AWZZ J AC 10 kohm (B),Semi-VR [VCO] VR102 RVR-M0018AWZZ J AC 470 ohms (B),Semi-VR
[Tape Speed]
PRICE RANK
VR202 RVR-Q0002BGZZ J AE 50 kohms (B)×2 [X-BASS] VR203~205 RVR-Q0001BGZZ J AC 100 kohm (B)×2
VR401 RVR-B0002BGZZ J 50 kohms (B)×2 [VOLUME]
DESCRIPTION
[Graphic Equalizer]
VARIABLE CAPACITORS
TC5,6 RTO-H1003SJZZ J AG Trimmer,5 pF TC7,8 RTO-H1001BGZZ J AD Trimmer,10 pF TC9 RVC-Z0001BGZZ J AF Fine Tuning VC1~4 RVC-R0001BGZZ J AK Variable Capacitance with
Trimmer (TC1~4)
VIBRATOR
XL801 RCRM-0008AWZZ J AF Ceramic,16.93 MHz
CAPACITORS
C2 VCCCPU1HH5R0J J AA 5 pF (CH),50V C4 VCCCPU1HH240J J AA 24 pF (CH),50V C5 VCKYPA1HB102K J AA 0.001 µF,50V C6,7 VCKYPA1HB472K J AB 0.0047 µF,50V C8,9 VCKZPA1HF223Z J AA 0.022 µF,50V C10 VCCCPU1HH150J J AA 15 pF (CH),50V C11 VCCCPU1HH220J J AA 22 pF (CH),50V C12 VCCCPU1HH3R0J J AA 3 pF (CH),50V C13 VCKZPA1HF223Z J AA 0.022 µF,50V C14 VCCCPU1HH5R0J J AA 5 pF (CH),50V C15 VCKZPA1HF223Z J AA 0.022 µF,50V C17 VCKZPA1HF223Z J AA 0.022 µF,50V C18 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C19 VCKYPA1HB331K J AA 330 pF,50V C20 VCKYPA1HB222K J AA 0.0022 µF,50V C21 VCCUPA1HJ5R0C J AA 5 pF (UJ),50V C22 VCKZPA1HF223Z J AA 0.022 µF,50V C23 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic C24~26 VCKZPA1HF223Z J AA 0.022 µF,50V C27 VCKYPA1HB472K J AB 0.0047 µF,50V C29 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C30 VCKZPA1HF223Z J AA 0.022 µF,50V C31 VCQYKA1HM472K J AB 0.0047 µF,50V,Mylar C32 VCQYKA1HM822K J AA 0.0082 µF,50V,Mylar C33 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic C34 VCKYPA1HB471K J AA 470 pF,50V C35 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic C36 92LCPU100V1500 J AC 0.0015 µF,100V C37,38 VCQYKA1HM123K J AA 0.012 µF,50V,Mylar C39~41 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C42 VCKZPA1HF223Z J AA 0.022 µF,50V C43 VCKYPA1HB221K J AA 220 pF,50V C101,102 VCKYPA1HB471K J AA 470 pF,50V C103,104 VCKYPA1HB471K J AA 470 pF,50V C105~108 VCKYPA1HB331K J AA 330 pF,50V C109,110 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C111,112 VCQYKA1HM153K J AB 0.015 µF,50V,Mylar C113~116 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C117,118 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C119,120 VCQYKA1HM333K J AB 0.033 µF,50V,Mylar C121,122 VCKYPA1HB331K J AA 330 pF,50V C123,124 VCKYPA1HB103K J AA 0.01 µF,50V C125,126 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C127 RC-GZA337AF1A J AB 330 µF,10V,Electrolytic C128 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic C129 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C131,132 VCKYPA1HB121K J AA 120 pF,50V C133,134 VCKYPA1HB151K J AA 150 pF,50V C137,138 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar C151 RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic C152 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C154 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C155 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C156 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C157 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C158,159 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic C160 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C180 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C181,182 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C183,184 VCKYPA1HB221K J AA 220 pF,50V C185,186 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C200 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C201,202 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic
– 1 –
Page 31
GX-CD1200W
NO. PARTS CODE
C203,204 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C205,206 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar C207,208 VCKYPA1HB471K J AA 470 pF,50V C209,210 VCQYKA1HM823K J AC 0.082 µF,50V,Mylar C211,212 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar C213,214 RC-GZA334AF1H J AA 0.33 µF,50V,Electrolytic C215,216 VCQYKA1HM562K J AA 0.0056 µF,50V,Mylar C217,218 RC-GZA474AF1H J AA 0.47 µF,50V,Electrolytic C219,220 VCQYKA1HM393K J AB 0.039 µF,50V,Mylar C221,222 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C251,252 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C253,254 VCKZPA1HF223Z J AA 0.022 µF,50V C255,256 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C257 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic C259,260 VCQYKA1HM392K J AA 0.0039 µF,50V,Mylar C301 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C302 VCQYKA1HM222K J AA 0.0022 µF,50V,Mylar C303 VCQYKA1HM562K J AA 0.0056 µF,50V,Mylar C304 VCKZPA1HF223Z J AA 0.022 µF,50V C305 VCQYKA1HM152K J AB 0.0015 µF,50V,Mylar C306 VCKYPA1HB391K J AA 390 pF,50V C307 VCKYPA1HB151K J AA 150 pF,50V C401,402 VCQYKA1HM682K J AA 0.0068 µF,50V,Mylar C403,404 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C405,406 VCQYKA1HM332K J AA 0.0033 µF,50V,Mylar C407,408 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C409,410 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C411 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C412 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C413,414 VCQYKA1HM102K J AA 0.001 µF,50V,Mylar C415,416 VCQYKA1HM154K J AB 0.15 µF,50V,Mylar C418 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C419,420 RC-GZA475AF1H J AB 4.7 µF,50V,Electrolytic C423 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C424 RC-GZA476AF1E J AB 47 µF,25V,Electrolytic C425~428 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar C429,430 RC-GZA106AF1C J AB 10 µF,16V,Electrolytic C433 VCKZPA1HF223Z J AA 0.022 µF,50V C505 RC-GZA476AF1C J AB 47 µF,16V,Electrolytic C506 VCKZPA1HF223Z J AA 0.022 µF,50V C508 RC-GZA107AF1C J AB 100 µF,16V,Electrolytic C509 VCKZPA1HF223Z J AA 0.022 µF,50V C510 RC-GZG338AF1E J 3300 µF,25V,Electrolytic C511 VCKZPA1HF223Z J AA 0.022 µF,50V C513,514 RC-GZA105AF1H J AB 1 µF,50V,Electrolytic C601 VCKZPA1HF223Z J AA 0.022 µF,50V C602 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C603 VCKZPA1HF223Z J AA 0.022 µF,50V C604 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic C651~654 VCKZPA1HF223Z J AA 0.022 µF,50V C801 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar
C802 VCKZPA1HF223Z J AA 0.022 µF,50V C804 VCCCPA1HH2R0C J AA 2 pF (CH),50V C805 VCKZPA1HF223Z J AA 0.022 µF,50V C806 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic C807 VCKZPA1HF473Z J AA 0.047 µF,50V C813 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C814 VCKZPA1HF473Z J AA 0.047 µF,50V C815 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C816 VCKZPA1HF223Z J AA 0.022 µF,50V C817 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C818 VCCSPA1HL560J J AA 56 pF,50V C819,820 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar C821 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C822 VCKZPA1HF473Z J AA 0.047 µF,50V C823 VCKZPA1HF223Z J AA 0.022 µF,50V C824 VCQYKA1HM104K J AB 0.1 µF,50V,Mylar C825 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C826 VCCSPA1HL470J J AA 47 pF,50V C827 VCQYKA1HM153K J AB 0.015 µF,50V,Mylar C828 VCKYPA1HB272K J AA 0.0027 µF,50V C829 VCKYPA1HB472K J AB 0.0047 µF,50V C830 VCQYKA1HM103K J AA 0.01 µF,50V,Mylar C832 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C833 VCQYKA1HM333K J AB 0.033 µF,50V,Mylar C834,835 VCKYPA1HB471K J AA 470 pF,50V C836~839 VCQYKA1HM473K J AB 0.047 µF,50V,Mylar C840~842 VCKZPA1HF473K J AA 0.047 µF,50V C843 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C844 RC-GZA107AF1A J AB 100 µF,10V,Electrolytic C845 VCKZPA1HF473Z J AA 0.047 µF,50V
PRICE
RANK
DESCRIPTION
[To Serial No.00404990 Only]
NO.
C846 RC-GZA225AF1H J AB 2.2 µF,50V,Electrolytic C847 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C848 RC-GZA226AF1C J AB 22 µF,16V,Electrolytic C849,850 VCKYPA1HB121K J AA 120 pF,50V C851,852 RC-GZA335AF1H J AB 3.3 µF,50V,Electrolytic C853 VCKZPA1HF223Z J AA 0.022 µF,50V C854 VCKYPA1HB682K J AB 0.0068 µF,50V C855 VCKZPA1HF223Z J AA 0.022 µF,50V C858 VCKZPA1HF223J J 0.022 µF,50V C859 VCKYPA1HB272K J AA 0.0027 µF,50V C860 VCKYPA1HB152K J AA 0.0015 µF,50V C863 RC-GZA476AF1A J AB 47 µF,10V,Electrolytic C893 RC-GZA227AF1A J AB 220 µF,10V,Electrolytic C894 VCKZPA1HF223Z J AA 0.022 µF,50V
PRICE
RANK
DESCRIPTIONPARTS CODE
RESISTORS
R1 VRD-ST2EE100J J AA 10 ohm,1/4W R2 VRD-ST2CD330J J AA 33 ohms,1/6W R3 VRD-ST2CD470J J AA 47 ohms,1/6W R4 VRD-ST2CD334J J AA 330 kohms,1/6W R5 VRD-ST2CD101J J AA 100 ohm,1/6W R7 VRD-ST2CD824J J AA 820 kohms,1/6W R8 VRD-ST2CD392J J AA 3.9 kohms,1/6W R9 VRD-ST2CD123J J AA 12 kohms,1/6W R10,11 VRD-ST2EE470J J AA 47 ohms,1/4W R12 VRD-ST2CD102J J AA 1 kohm,1/6W R13 VRD-ST2EE101J J AA 100 ohm,1/4W R14 VRD-ST2CD104J J AA 100 kohm,1/6W R15,16 VRD-ST2CD103J J AA 10 kohm,1/6W R17,18 VRD-ST2CD272J J AA 2.7 kohms,1/6W R19 VRD-ST2CD153J J AA 15 kohms,1/6W R20 VRD-ST2EE100J J AA 10 ohm,1/4W R100 VRD-ST2EE151J J AA 150 ohms,1/4W R101,102 VRD-ST2CD101J J AA 100 ohm,1/6W R105,106 VRD-ST2CD184J J AA 180 kohms,1/6W R107,108 VRD-ST2CD103J J AA 10 kohm,1/6W R109,110 VRD-ST2CD682J J AA 6.8 kohms,1/6W R111,112 VRD-ST2CD223J J AA 22 kohms,1/6W R113,114 VRD-ST2CD124J J AA 120 kohms,1/6W R115,116 VRD-ST2CD681J J AA 680 ohms,1/6W R117,118 VRD-ST2CD334J J AA 330 kohms,1/6W R119,120 VRD-ST2CD101J J AA 100 ohm,1/6W R121~124 VRD-ST2CD103J J AA 10 kohm,1/6W R127,128 VRD-ST2CD223J J AA 22 kohms,1/6W R129,130 VRD-ST2CD154J J AA 150 kohms,1/6W R131,132 VRD-ST2CD122J J AA 1.2 kohms,1/6W R133,134 VRD-ST2CD823J J AA 82 kohms,1/6W R135,136 VRD-ST2CD103J J AA 10 kohm,1/6W R151 VRD-ST2CD222J J AA 2.2 kohms,1/6W R152 VRD-ST2CD472J J AA 4.7 kohms,1/6W R153 VRD-ST2CD222J J AA 2.2 kohms,1/6W R154 VRD-ST2CD561J J AA 560 ohms,1/6W R161 VRD-ST2CD105J J AA 1 Mohm,1/6W R165 VRD-ST2CD103J J AA 10 kohm,1/6W R166 VRD-ST2EE561J J AA 560 ohms,1/4W R168,169 VRD-ST2CD103J J AA 10 kohm,1/6W R170,171 VRD-ST2CD333J J AA 33 kohms,1/6W R172,173 VRD-ST2CD103J J AA 10 kohm,1/6W R174 VRD-ST2CD223J J AA 22 kohms,1/6W R177 VRD-ST2CD102J J AA 1 kohm,1/6W R180 VRD-ST2EE561J J AA 560 ohms,1/4W R181,182 VRD-ST2CD102J J AA 1 kohm,1/6W R183,184 VRD-ST2CD334J J AA 330 kohms,1/6W R185,186 VRD-ST2CD221J J AA 220 ohms,1/6W R187,188 VRD-ST2CD392J J AA 3.9 kohms,1/6W R200 VRD-ST2EE331J J AA 330 ohms,1/4W R201,202 VRD-ST2CD102J J AA 1 kohm,1/6W R203,204 VRD-ST2CD222J J AA 2.2 kohms,1/6W R205 VRD-ST2CD472J J AA 4.7 kohms,1/6W R206 VRD-ST2CD332J J AA 3.3 kohms,1/6W R207 VRD-ST2CD472J J AA 4.7 kohms,1/6W R208 VRD-ST2CD332J J AA 3.3 kohms,1/6W R211,212 VRD-ST2CD102J J AA 1 kohm,1/6W R251,252 VRD-ST2CD682J J AA 6.8 kohms,1/6W R253,254 VRD-ST2CD393J J AA 39 kohms,1/6W R255,256 VRD-ST2EE121J J AA 120 ohms,1/4W R257,258 VRD-ST2CD103J J AA 10 kohm,1/6W R259,260 VRD-ST2EE121J J AA 120 ohms,1/4W R301 VRD-ST2EE331J J AA 330 ohms,1/4W R302,303 VRD-ST2EE101J J AA 100 ohm,1/4W R304 VRD-ST2EE100J J AA 10 ohm,1/4W
– 2 –
Page 32
GX-CD1200W
PARTS CODE NO. PARTS CODE
R305 VRD-ST2EE273J J AA 27 kohms,1/4W R306 VRD-ST2EE470J J AA 47 ohms,1/4W R351,352 VRD-ST2CD473J J AA 47 kohms,1/6W R353,354 VRD-ST2CD273J J AA 27 kohms,1/6W R401,402 VRD-ST2CD104J J AA 100 kohm,1/6W R403,404 VRD-ST2CD103J J AA 10 kohm,1/6W R405,406 VRD-ST2CD272J J AA 2.7 kohms,1/6W R407~410 VRD-ST2CD123J J AA 12 kohms,1/6W R411 VRD-ST2EE331J J AA 330 ohms,1/4W R412,413 VRD-ST2CD103J J AA 10 kohm,1/6W R415,416 VRD-ST2CD332J J AA 3.3 kohms,1/6W R417,418 VRD-ST2CD223J J AA 22 kohms,1/6W R419,420 VRD-ST2CD332J J AA 3.3 kohms,1/6W R425,426 VRD-ST2CD102J J AA 1 kohm,1/6W R427,428 VRD-ST2CD472J J AA 4.7 kohms,1/6W R429 VRD-ST2CD104J J AA 100 kohm,1/6W R431 VRD-ST2CD273J J AA 27 kohms,1/6W R433~436 VRD-ST2CD2R2J J AA 2.2 ohms,1/6W R437,438 VRD-ST2EE121J J AA 120 ohms,1/4W R440 VRD-ST2EE471J J AA 470 ohms,1/4W R441,442 VRD-ST2CD153J J AA 15 kohms,1/6W R511~513 VRD-ST2CD103J J AA 10 kohm,1/6W R514 VRD-ST2CD104J J AA 100 kohm,1/6W R515 VRD-ST2CD121J J AA 120 ohms,1/6W R516 VRD-ST2CD302J J AA 3.6 kohms,1/6W R518,519 VRD-ST2CD102J J AA 1 kohm,1/6W R520,521 VRD-ST2CD103J J AA 10 kohm,1/6W R601 VRD-ST2EE271J J AA 270 ohms,1/4W R602 VRD-ST2EE101J J AA 100 ohm,1/4W R801 VRD-ST2EE220J J AA 22 ohms,1/4W R802 VRD-ST2CD222J J AA 2.2 kohms,1/6W
R803 VRD-ST2CD823J J AA 82 kohms,1/6W R804 VRD-ST2CD683J J AA 68 kohms,1/6W R805 VRD-ST2CD393J J AA 39 kohms,1/6W R806 VRD-ST2CD272J J AA 2.7 kohms,1/6W R807 VRD-ST2CD102J J AA 1 kohm,1/6W R811 VRD-ST2CD223J J AA 22 kohms,1/6W R812 VRD-ST2CD102J J AA 1 kohm,1/6W R820 VRD-ST2CD473J J AA 47 kohms,1/6W R821,822 VRD-ST2CD223J J AA 22 kohms,1/6W R824 VRD-ST2CD103J J AA 10 kohm,1/6W R826 VRD-ST2CD224J J AA 220 kohms,1/6W R827 VRD-ST2CD153J J AA 15 kohms,1/6W R828 VRD-ST2CD103J J AA 10 kohm,1/6W R829 VRD-ST2CD332J J AA 3.3 kohms,1/6W R830 VRD-ST2CD103J J AA 10 kohm,1/6W R831~834 VRD-ST2CD332J J AA 3.3 kohms,1/6W R835,836 VRD-ST2CD153J J AA 15 kohms,1/6W R839 VRD-ST2CD473J J AA 47 kohms,1/6W R840 VRD-ST2EE100J J AA 10 ohm,1/4W R844 VRD-ST2CD332J J AA 3.3 kohms,1/6W R846 VRD-ST2CD331J J AA 330 ohms,1/6W R847 VRD-ST2CD102J J AA 1 kohm,1/6W R848 VRD-ST2CD222J J AA 2.2 kohms,1/6W R849 VRD-ST2CD682J J AA 6.8 kohms,1/6W R851~853 VRD-ST2CD222J J AA 2.2 kohms,1/6W R857,858 VRD-ST2CD562J J AA 5.6 kohms,1/6W R861 VRD-ST2CD332J J AA 3.3 kohms,1/6W R863 VRD-ST2CD332J J AA 3.3 kohms,1/6W R865 VRD-ST2CD102J J AA 1 kohm,1/6W R891 VRD-ST2CD683J J AA 68 kohms,1/6W
R892 VRD-ST2CD563J J AA 56 kohms,1/6W R893~895 VRD-ST2CD683J J AA 68 kohms,1/6W R896 VRD-ST2CD563J J AA 56 kohms,1/6W
PRICE
RANK
DESCRIPTIONNO.
[To Serial No.00404990 Only]
[From Serial No.00504991] [From Serial No.00504991] [From Serial No.00504991] [From Serial No.00504991]
OTHER CIRCUITRY PARTS
BI801/CNS801 QCNWN0026BGZZ J Connector Ass’y,8/8Pin BI802/CNS802 QCNWN0027BGZZ J Connector Ass’y,5/5Pin
BI802/CNS802 QCNWN0032BGZZ J Connector Ass’y,7/7Pin BI803/CNS803 QCNWN0028BGZZ J Connector Ass’y,6/6Pin
BI804/CNS804 QCNWN0031BGZZ J Connector Ass’y,6/6Pin CNP101 QCNCM705CAFZZ J AA Plug,3Pin CNP102 QCNCM705DAFZZ J AB Plug,4Pin CNP103 QCNCM698JAFZZ J AC Plug,9Pin
[To Serial No.00404990] [From Serial No.00504991]
PRICE RANK
CNP501 QTANA0001BGZZ J AD Terminal,Speaker CNP601 QCNCM035BAWZZ J AB Plug,2Pin CNP803 92LCONE6P53254 J AC Plug,6Pin CNP804 QCNCM705FAFZZ J AB Plug,6Pin CNS101 QCNWN0001BGZZ J AD Connector Ass’y,3Pin CNS102 QCNWN0002BGZZ J AE Connector Ass’y,4Pin CNS103 QCNWN0003BGZZ J AF Connector Ass’y,9Pin CNS601 QCNWN0006BGZZ J AD Connector Ass’y,2Pin
! F601 QFS-D402ABGNI J AC T4A L 250V
FW1 QCNWN0038BGZZ J Flat Wire,4Pin FW2 QCNWN0014BGZZ J AA Flat Wire,2Pin FW801 QCNWN0030AFZZ J AG Flat Wire,10Pin FW802 QCNWN0029AFZZ J Flat Wire,2Pin J151 QJAKA0004BGZZ J Jack,Mic J401 QJAKM0001BGZZ J AE Jack,Headphones LCD801 RV-LX0001BGZZ J LCD Display M501(300-10) 92L1959123012 J Motor with Pulley [Tape] M801 92LMMTR1651B J AL Motor with Chassis [Sled] M802 92LMMTR1854A J AP Motor with Gear [Spindle] MIC151 RMICC0001BGZZ J AF Built-in Microphone
! SO601 QSOCA0006SJZZ J AB AC Socket
SP401,402 VSP0012PBG28A J Speaker,Woofer SP403,404 RALMB0001BGZZ J AC Speaker,Tweeter SW1 QSW-S9001BGZZ J AE Switch,Slide Type
SW101 QSW-S9002BGZZ J AD Switch,Slide Type SW102 QSW-S9003BGZZ J AC Switch,Slide Type [Beat Cancel]
SW103 QSW-S9004BGZZ J AC Switch,Slide Type [Dubbing SW401 QSW-P9001BGZZ J AE Switch,Push Type [Surround]
SW501 QSW-S9005BGZZ J AD Switch,Slide Type
! SW601 QSW-S0004SJZZ J AK Switch,Slide Type
SW702 QSWF9001AW01 J Switch,Push Type [Pickup In] SW801 QSW-K0008AWZZ J AC Switch,Key Type [Play/Pause] SW801 92LSWICHT1663 J AC Switch,Key Type [Play/Pause] SW802 QSW-K0008AWZZ J AC Switch,Key Type [Stop] SW803 QSW-K0008AWZZ J AC Switch,Key Type [Cue/Track Up] SW804 QSW-K0008AWZZ J AC Switch,Key Type
SW810 QSW-P0004AWZZ J AE Switch,Push Type [Open/Close] SW901(300-12) 92L640101149 J Switch,Leaf Type [Tape 1 Main] SW902(300-11) 92L640101149 J Switch,Leaf Type [Tape 2 Main] SW903(300-13) 92L640101149 J Switch,Leaf Type [Tape 2 Play] SW904(300-14) 92L64030204 J Switch,Slide Type
DESCRIPTION
[Band Selector] [Record/Playback]
Speed/Mic/FM Mode]
[Function Selector] [Voltage Selector]
[Review/Track Down]
[Tape 2 Direction]
CD MECHANISM PARTS
301 NGERH0011AWZZ J AC Gear,Middle 302 NGERH0012AWZZ J AC Gear,Drive 303 MLEVP0080AWZZ J AC Rail,Guide 304 NSFTM0020AWFW J AD Shaft,Guide 305 92LMCUSN1524A J AD Cushion
! 306 92LHPC1LASY J Pickup Unit Ass’y ! 306 92LHPC1LXASY J BD Pickup Unit Ass’y
307 PCOVP1001AWSA J AE Cover,CD Mechanism 701 XBSSD26P06000 J AA Screw,ø2.6×6mm 702 XHBSD20P05000 J AA Screw,ø2×5mm 703 XBBSD20P03000 J AA Screw,ø2×3mm 704 LX-WZ1070AFZZ J AA Washer,ø1.5×ø3.8×0.25mm M801 92LMMTR1651B J AL Motor with Chassis [Sled] M802 92LMMTR1854A J AP Motor with Gear [Spindle] SW702 QSWF9001AW01 J Switch,Push Type [Pickup In]
[To Serial No.00404990] [From Serial No.00504991]
CABINET PARTS
201 GCABA1003BGSA J Front Cabinet [GL] 201 GCABA1003BGSB J Front Cabinet [BK] 202 GFTAC0001BGSB J AK Cassette Holder [Tape 1] [BK] 202 GFTAC0001BGSC J Cassette Holder [Tape 1] [GL] 203 GFTAC0002BGSB J AK Cassette Holder [Tape 2] [BK] 203 GFTAC0002BGSC J Cassette Holder [Tape 2] [GL] 204 HBDGA1003BGSA J Badge,SHARP 205 HBDGS1001BGSA J AF Sheet,Surround Sound System 206 HDECQ0001BGSA J AH Panel,Display 207 HDECQ0004BGSA J AD Ring,Volume Knob 208 HDECQ0017BGSA J Panel,Cassette Holder [Tape 1]
– 3 –
Page 33
GX-CD1200W
NO. PARTS CODE
209 HDECQ0008BGSA J AD Panel,Cassette Holder [Tape 2] 210 HDECZ0001BGSA J AC Panel,Dial Pointer 211 HSSND0001BGSA J AC Dial Pointer 212 JKNBQ0001BGSC J Knob,Tuning 213 LANGT0001BGFW J AD Bracket,Front Cabinet 214 MLIFP0001BGZZ J AD Gear,Cassette Holder 215 MSPRD0001BGFW J AB Spring,Cassette Holder Up 216 NGERH0002BGZZ J AC Gear,Tuning Knob 218 LANGG0001BGFW J AB Guide,Dial Pointer 219 HDECQ0005BGSA J AC Cap,Volume Knob 220 JKNBK0001BGSB J Knob,Volume 221 LHLDW1033CE00 J Nylon Band 222 JBTN-0001BGSB J AC Button,Record [Tape 1] [BK] 222 JBTN-0001BGSC J Button,Record [Tape 1] [GL] 223 JBTN-0002BGSB J AC Button,Play [Tape 1] [BK] 223 JBTN-0002BGSC J Button,Play [Tape 1] [GL] 224 JBTN-0003BGSB J AC Button,Rewind [Tape 1] [BK] 224 JBTN-0003BGSC J Button,Rewind [Tape 1] [GL] 225 JBTN-0004BGSB J AC Button,Fast Forward [Tape 1]
225 JBTN-0004BGSC J Button,Fast Forward [Tape 1] 226 JBTN-0005BGSB J AC Button,Stop/Eject [Tape 1] [BK]
226 JBTN-0005BGSC J Button,Stop/Eject [Tape 1] [GL] 227 JBTN-0006BGSB J AC Button,Pause [Tape 1] [BK] 227 JBTN-0006BGSC J Button,Pause [Tape 1] [GL] 228 JBTN-0007BGSB J AC Button,Reverse Mode [Tape 2]
228 JBTN-0007BGSC J Button,Reverse Mode [Tape 2] 229 JBTN-0008BGSB J AC Button,Play [Tape 2] [BK]
229 JBTN-0008BGSC J Button,Play [Tape 2] [GL] 230 JBTN-0009BGSB J AC Button,Rewind [Tape 2] [BK] 230 JBTN-0009BGSC J Button,Rewind [Tape 2] [GL] 231 JBTN-0010BGSB J AC Button,Fast Forward [Tape 2]
231 JBTN-0010BGSC J Button,Fast Forward [Tape 2] 232 JBTN-0011BGSB J AC Button,Stop/Eject [Tape 2] [BK]
232 JBTN-0011BGSC J Button,Stop/Eject [Tape 2] [GL] 233 JBTN-0012BGSB J AC Button,Direction [Tape 2] [BK] 233 JBTN-0012BGSC J Button,Direction [Tape 2] [GL] 234 LANGF0001BGZW J Support,Mechanism Button Shaft 235 LHLDZ8001BG00 J AC Holder,Mic 236 LHLDZ1002BGZZ J AC Holder,LED A 237 MSPRC0001BGFJ J AC Spring,Battery,­238 PRDAR0001BGFW J AL Heat Sink,Main 239 NGERK0001BGZZ J AD Dial Drum 240 PSHEP0001BGSA J AD Sheet,LED,Left 241 PSHEP0002BGSA J AD Sheet,LED,Right 242 JKNBZ0001BGSA J AC Knob,Fine Tuning 243 PCOVZ9001BGZZ J AB Cover,Dial Pointer 244 MSPRP0001BGFW J AC Plate,Record 245 GCABB1003BGSA J Rear Cabinet [GL] 245 GCABB1003BGSB J Rear Cabinet [BK] 246 GLEGG0001BG00 J AB Cushion,Leg 247 JHNDP1002BGSA J Handle [GL] 247 JHNDP1002BGSB J Handle [BK] 248 LHLDQ1001BGZZ J AE Holder,AC Socket/Voltage
249 MSPRB0002BGFW J AB Spring,Rod Antenna 250 MSPRC0002BGFJ J AC Spring,Battery,+/­251 MSPRC0003BGFJ J AC Spring,Battery,+/­253 QANTR0002BGZZ J AK Rod Antenna 254 LHLDR1001BGZZ J AD Holder,Tuning 255 NGERK0002BGZZ J AB Gear,Tuning A 256 NGERK0003BGZZ J AB Gear,Tuning B 257 JKNBM0001BGSA J AD Button,Surround 258 JKNBP0001BGSA J AA Knob,Function 259 JKNBP0001BGSA J AA Knob,Dubbing Speed 260 JKNBP0002BGSA J AB Knob,Band Selector 261 LHLDS1002BGZZ J AC Holder,Record Lever 262 MLEVP0002BGZZ J AB Lever,Record 263 GFTAB1001BGSB J AE Battery Compartment Lid [BK] 263 GFTAB1001BGSC J Battery Compartment Lid [GL] 264 TSPC-0017BGZZ J Label,Specifications [GL]
264 TSPC-0018BGZZ J Label,Specifications [GL] 264 TSPC-0020BGZZ J Label,Specifications [GL]
PRICE
RANK
DESCRIPTION
[BK] [GL]
[BK] [GL]
[BK] [GL]
Selector
[For Malaysia/Asia Middle East/ Africa]
[For Jordan/Egypt] [For Thailand]
NO.
264 TSPC-0026BGZZ J Label,Specifications [BK]
264 TSPC-0027BGZZ J Label,Specifications [BK] 264 TSPC-0028BGZZ J Label,Specifications [BK] 264 TSPC-0029BGZZ J Label,Specifications [GL] 264 TSPC-0030BGZZ J Label,Specifications [BK] 266 PRDAR0002BGFW J Heat Sink,Sub
267 GCABC1003BGSA J Top Cabinet [GL] 267 GCABC1003BGSB J Top Cabinet [BK] 268 GFTAT1001BGSA J CD Lid [GL] 268 GFTAT1001BGSB J CD Lid [BK] 269 HPNLZ1001BGSA J Panel,Decoration 270 HPNLZ1002BGSA J Panel,LCD 271 JBTN-0024BGSA J Button,CD Lid Open [GL] 271 JBTN-0024BGSB J Button,CD Lid Open [BK] 272 MLEVP0003BGZZ J Lock Lever,CD Lid 273 JKNBK0002BGSA J Button,Function 274 LHLDM1001BGZZ J Stabilizer 275 PMAGF0001BGZZ J Magnet 276 LHLDZ1003BGZZ J Holder,LCD 277 MSPRD0002BGFJ J Spring,CD Lid
! 278 QFSHD0017CEZZ J Holder,Fuse ! 279 QFSHD0018CEZZ J Holder,Fuse
280 MSPRB0003BGFW J Spring,CD LID Open Button 300 CMECB0001BG01 J BL Tape Mechanism Ass’y 300- 1 92L192104309 J Pinch Roller Arm Ass’y 300- 2 92L195904302 J Pinch Roller Arm Ass’y,Rewind 300- 3 92L195904301 J Pinch Roller Arm Ass’y,Fast
300- 4 92L6201-01-111 J Head,Record/Playback,Tape 1 300- 5 92L6209-10-10 J Head,Erase,Tape 1 300- 6 92L6216-07-01 J Head,Playback,Tape 2 300- 7 92L19210703 J FF/REW Belt 300- 8 92L182112173 J Main Belt,Tape 1 300- 9 92L182112142 J Main Belt,Tape 2 300-10(M501) 92L1959123012 J Motor with Pulley [Tape] 300-11(SW902) 92L640101149 J Switch,Leaf Type [Tape 2 Main] 300-12(SW901) 92L640101149 J Switch,Leaf Type [Tape 1 Main] 300-13(SW903) 92L640101149 J Switch,Leaf Type [Tape 2 Play] 300-14(SW904) 92L64030204 J Switch,Slide Type
601 XEBSD30P10000 J AA Screw,ø3×10mm 602 XJBSD30P08000 J AA Screw,ø3×8mm 603 XBPSD26P04JS0 J Screw,ø2.6×4mm 604 XHBSD20P04000 J AA Screw,ø2×4mm 605 XJSSD30P10000 J AA Screw,ø3×10mm 606 XBBSF30P10000 J AA Screw,ø3×10mm 607 XJBSD40P16000 J AB Screw,ø4×16mm 608 XEBSD30P20000 J AA Screw,ø3×20mm 609 XHSSF30P06000 J AA Screw,ø3×6mm 610 XEBSD30P10000 J AA Screw,ø3×10mm 611 LX-JZ0002AWFD J AA Screw,ø3×10mm 612 XESSD30P10000 J Screw,ø3×10mm 613 LX-EZ0005AWFD J AA Screw,ø2.6×10mm
PRICE
RANK
DESCRIPTIONPARTS CODE
[For Malaysia/Asia Middle East/ Africa]
[For Jordan/Egypt] [For Thailand] [For Australia] [For Australia]
Forward
[Tape 2 Direction]
SPEAKER BOX PARTS
301 CCAB-120LBG01G J Front Panel,Ass’y,Left [GL] 301 CCAB-120LBG01K J Front Panel,Ass’y,Left [BK] 302 CCAB-120RBG01G J Front Panel,Ass’y,Right [GL] 302 CCAB-120RBG01K J Front Panel,Ass’y,Right [BK] 303 GCABD1001BGSB J AQ Speaker Box,Left [BK] 303 GCABD1001BGSC J Speaker Box,Left [GL] 304 GCABF1001BGSB J AQ Speaker Box,Right [BK] 304 GCABF1001BGSC J Speaker Box,Right [GL] 305 GLEGG0001BG00 J AB Cushion,Leg,Speaker 306 LHLDW1001BGSB J AB Holder,Speaker Cord [BK] 306 LHLDW1001BGSC J Holder,Speaker Cord [GL] 307 QCNWG0001BGZZ J AE Cord,Speaker 308 LPLTW0001BGZZ J AC Support H,Speaker Box 309 LPLTW0002BGZZ J AC Support V,Speaker Box 701 XEBSD30P10000 J AA Screw,ø3×10mm 702 XJBSD40P16000 J AB Screw,ø4×16mm SP401,402 VSP0012PBG28A J Speaker,Woofer SP403,404 RALMB0001BGZZ J AC Speaker,Tweeter
– 4 –
Page 34
GX-CD1200W
PARTS CODE NO. PARTS CODE
PRICE
RANK
DESCRIPTIONNO.
ACCESSORIES/PACKING PARTS
! QACCA0001SJ00 J AS AC Power Supply Cord ! QACCE0007AW00 J AH AC Power Supply Cord ! QACCL0002AW00 J AN AC Power Supply Cord ! QPLGA0250AFZZ J AF Adaptor,AC Plug ! QPLGA0253AFZZ J AE Adaptor,AC Plug
SPAKA0003BGZZ J Packing Add.,Unit SPAKC0023BGZZ J Packing Case [GL]
[For Malaysia]
SPAKC0024BGZZ J Packing Case [GL]
[Except for Malaysia]
SPAKC0033BGZZ J Packing Case [BK]
[For Malaysia]
SPAKC0034BGZZ J Packing Case [BK]
[Except for Malaysia]
SSAKA0002BGZZ J AB Polyethylene Bag,AC Plug
Adaptor SSAKH0002BGZZ J AB Polyethylene Bag,Accessories SSAKH0004BGZZ J AB Polyethylene Bag,Unit SSAKH0005BGZZ J AB Polyethylene Bag,Speaker TGANE0002BG03 J Warranty Card [For Philippines] TGANE0003BGZZ J Warranty Card [For Australia] TINSZ0008BGZZ J Operation Manual TLABB0001BGZZ J AB Label,Japan TLABB0002BGZZ J AC Label,Japan TLABE0005BGZZ J Label,Ean Bar Code [GL] TLABE0008BGZZ J Label,Ean Bar Code [BK] TLABR1137BGZZ J Label,Bar Code [GL] TLABR1138BGZZ J Label,Bar Code [BK] TLABS0002BGZZ J Label,Laser TLABS0003BGZZ J Label,Class 3 TLABZ0001BGZZ J Label,Contru origin for Set TLABZ0002BGZZ J Label,Contru origin for P-case TLABZ0009BGZZ J Label,Feature,Left [For Malaysia] TLABZ0010BGZZ J Label,Feature,Right
[For Malaysia] TLABZ0011BGZZ J Label,Feature,Left
[Except for Malaysia] TLABZ0012BGZZ J Label,Feature,Right
[Except for Malaysia]
P.W.B. ASSEMBLY (Not Replacement Item)
PWB-A1~8 DUNTK0003BG01 J — Main/Graphic Equalizer/Volume/
PWB-B QPWBF0027AWZZ J AD CD Motor (PWB Only) PWB-C1~3 DUNTK0004BG01 J — CD Servo/CD Control/Switch
Fine Tuning/Terminal A/
Terminal B/Power/Holder
(Combined Ass’y)
(Combined Ass’y)
OTHER SERVICE PART
UDSKA0004AFZZ J AZ Pickup Lens Cleaner
PRICE RANK
DESCRIPTION
– 5 –
Page 35
GX-CD1200W
A
307
306
B
701
304
701
C
704
302
702
D
301
303
703x2
E
M802
F
305
M801
305x2
G
SW702
PWB-B
H
1
2
Figure 6 CD MECHANISM EXPLODED VIEW
34 5
– 6 –
6
Page 36
GX-CD1200W
269
248
601x2
272
T601
267
240
211
208
271
278
SW601
PWB-A7
210
241
PWB-A8
214
SO601
236
242
279
280
601
214x2
213
610x2
601
218
258
601
PWB-A4
202
268
PWB-C3
607
609
PWB-A6
PWB-A5
PWB-A2
PWB-A3
257
601
222
215
262
223
237
605x5
259
224
275
VR401
260
225
209
246x2
601x2
226
203
227
274
228
601x2
229
608x3
245
249
246
603
602x2
261
TAPE MECHANISM
230
231
232
215
239
254
IC502
233
277
601x2
PWB-A1
601
Q601
605x6
253
264
609
611
255
256
602
266
IC402
244
300(300-1, 300-2, 300-3, 300-4, 300-5, 300-6, 300-7, 300-8,300-9,300-10(M501), 300-11(SW902), 300-12(SW901), 300-13(SW903), 300-14(SW904)
CD
A
B
613x3
601x3
PWB-C1
C
607x3
607x2
MECHANISM
PWB-C2
273
276
LCD801
601x3
D
601
213
201
E
204
243
205
270
MIC151
235
F
216
212
206
G
With VR401
219
207
220
221
263
612x3
601
Grease
Silicon
Grease
602x2
250
246
Silicon
238
604
247
606
251
251
234x2
H
Note: Only the unit and consumale parts are supplied as parts supply for the Tape mechanism.
1
2
34 5
Figure 7 CABINET EXPLODED VIEW
– 7 –
6
Page 37
GX-CD1200W
A
301(LEFT)
303(LEFT) 304(RIGHT)
702x5
302(RIGHT)
SP403(L-CH)
307
SP404(R-CH)
B
701x4
306
C
308
D
305
SP401(L-CH) SP402(R-CH)
309
305
305
305
TWEETER
SP403(L-CH)
E
BLACK
F
TWEETER
RED
SP403(L-CH) SP404(R-CH)
G
WOOFER SP401(L-CH) SP402(R-CH)
SP404(R-CH)
BLACK
WOOFER
SP401(L-CH)
SP402(R-CH)
RED
H
1
2
Figure 8 SPEAKER EXPLODED VIEW
34 5
– 8 –
6
Page 38
GX-CD1200W
— M E M O —
– 9 –
Page 39
— M E M O —
GX-CD1200W
– 10
Page 40
GX-CD1200W
COPYRIGHT 2000 BY SHARP CORPORATION
©
ALL RIGHTS RESERVED.
No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any from or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.
SHARP CORPORATION Communication Systems Group Quality & Reliability Control Center Higashihiroshima, Hiroshima 739-0192, Japan
Printed in Japan
A0006-1408DS•HA•I
SCA • SCNZ • EX
Loading...