Sharp GX34 User Manual

Declaration of Conformity

Hereby, Sharp Telecommunications of Europe Limited, declares that this GX34 is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. A copy of the original declaration of conformity can be found at the following Internet address: http://www.sharp-mobile.com

Sharp Telecommunications of Europe Ltd. Azure House, Bagshot Road, Bracknell, Berkshire RG12 7QY UK

http://www.sharp-mobile.com

Introduction

Congratulations and thank you for choosing the GX34.

About This User Guide

This User Guide is carefully designed to help you learn about your phone’s features and operations quickly and effectively.

NOTICE

•

We strongly recommend that you keep separate permanent written records of all important data. Data may be lost or altered in virtually any electronic memory product under certain circumstances. Therefore, we assume no responsibility for data lost or otherwise rendered unusable, whether as a result of improper use, repairs, defects, battery replacement, use after the specified battery life has expired or any other cause.

• We assume no responsibility, directly or indirectly, for financial losses or claims from third parties resulting from the use of this product and any of its functions, such as stolen credit card numbers, the loss or alteration of stored data, etc.

• All company and/or product names are trademarks and/or registered trademarks of their respective holders.

• Screen layout illustrated in this User Guide may differ from the actual one. The information described in this User Guide is subject to change without notice.

• All the functions described in this User Guide may not be supported in all networks.

• We assume no responsibility for downloaded contents, information, etc. from network.

• Occasionally, a few black or bright pixels may appear on the screen. Please note that this will not have any impact on any of the features or performance.

Intellectual Property Rights

According to copyright laws, the reproduction, alteration and use of material which is protected by copyright (music, pictures, etc.) is only permitted for personal or private use. If the user is not in possession of more extensive copyright or has not received the explicit permission from the copyright owner to reproduce, alter or use a copy which has been made or modified in this way, this is considered to be a violation of the copyright laws and gives the copyright owner the right to claim for damages. For this reason, avoid the illegal use of material which is protected by copyright.

Windows is a registered trademark of Microsoft Corporation in the United States and/or other countries.

Introduction 1

Powered by JBlend™ Copyright 19972007 Aplix Corporation. All rights reserved. JBlend and all JBlend-based trademarks and logos are trademarks or registered trademarks of Aplix Corporation in Japan and other countries.

Licensed by Inter Digital Technology Corporation under one or more of the following United States Patents and/or their domestic or foreign counterparts and other patents pending, including U.S. Patents: 4,675,863: 4,779,262: 4,785,450 & 4,811,420.

T9 Text Input is licensed under one or more of the following: U.S. Pat. Nos. 5,818,437, 5,953,541, 5,187,480, 5,945,928, and 6,011,554; Australian Pat. No. 727539; Canadian Pat. No. 1,331,057; United Kingdom Pat. No. 2238414B; Hong Kong Standard Pat. No. HK0940329; Republic of Singapore Pat. No. 51383; Euro. Pat. No. 0 842 463 (96927260.8) DE/ DK, FI, FR, IT, NL,PT.ES,SE,GB; Republic of Korea Pat. Nos. KR201211B1 and KR226206B1; and additional patents are pending worldwide.

is a registered trademark of HI

/Micro3D Edition™

2 Introduction

Bluetooth is a trademark of the Bluetooth SIG, Inc.

The Bluetooth word mark and logos are owned by the Bluetooth SIG, Inc. and any use of such marks by Sharp is under license. Other trademarks and trade names are those of their respective owners.

CP8 PATENT

microSD™ is a trademark of the SD Card Association.

This product is licensed under the MPEG-4 Visual Patent Portfolio License for the personal and non-commercial use of a consumer to (i) encode video in compliance with the MPEG-4 Video Standard (“MPEG-4 Video”) and/or (ii) decode MPEG-4 Video that was encoded by a consumer engaged in a personal and non-commercial activity and/or was obtained from a licensed video provider. No license is granted or implied for any other use. Additional information may be obtained from MPEG LA. See http://www.mpegla.com.

This product is licensed under the MPEG-4 Systems Patent Portfolio License for encoding in compliance with the MPEG4 Systems Standard, except that an additional license and payment of royalties are necessary for encoding in connection with (i) data stored or replicated in physical media which is paid for on a title by title basis and/or (ii) data which is paid for on a title by title basis and is transmitted to an end user for permanent storage and/or use. Such additional license may be obtained from MPEG LA, LLC. See http:// www.mpegla.com for additional details.

MPEG Layer-3 audio coding technology licensed from Fraunhofer IIS and Thomson.

Useful Functions and Services

Your phone offers you the following features:

• A built-in digital camera for taking pictures and video clips.

• A message function for reading and creating SMS messages.

• MMS (Multimedia Messaging Services) for sending picture, sound and video messages to brighten someone’s day.

• A WAP browser for accessing information on the mobile Internet.

• Java™ applications. You can also download various applications from Vodafone via the mobile Internet.

• The external display for quickly checking the information of incoming calls or messages.

• Email for sending up to 2000 characters and receiving mail with attachments.

• A voice recorder function for recording and playing back voice clips.

•A Bluetooth

wireless technology interface for establishing contact and transmitting data with certain devices. You can transmit pictures, sounds, and video clips to OBEX-enabled phones.

• A data synchronisation function for synchronising the Contacts List and schedule entries with Microsoft Outlook or Outlook Express on a PC.

• A schedule alarm for creating and sending schedule entries with alarm settings.

• A music player that can play back MP3 and AAC format sound files.

• A microSD™ memory card slot that expands connectivity with a PC using a memory card.

Introduction 3

SAFETY PRECAUTIONS

Your phone conforms to international regulations in so far as it is used under normal conditions and in accordance with the following instructions.

Sharp and Vodafone disclaim any liability for damage which may result as a consequence of improper use or use contrary to the instructions contained herein.

Read the safety information sections of this user guide on pages 4 to 15.

Do not use hand-held while driving.

For body-worn operation, maintain a separation of

1.5 cm.

Small parts may cause a choking hazard.

This device may produce a loud sound.

Keep away from pacemakers and other personal medical devices.

Switch off when instructed in hospitals and medical facilities.

Switch off when instructed in aircrafts and airports.

4 SAFETY PRECAUTIONS

Switch off in explosive environments.

Do not use while re-fuelling.

This device may produce a bright or flashing light. (* The flashing light feature is not available on all products.)

Do not dispose of in a fire.

Avoid contact with magnetic media.

Avoid extreme temperatures.

Avoid contact with liquid, keep dry.

Do not attempt to disassemble.

Do not rely on this device for emergency communications.

Only use approved accessories.

RADIOFREQUENCY (RF) EXPOSURE

General Statement on RF Energy

Your phone contains a transmitter and a receiver. When it is ON, it receives and transmits RF energy. When you communicate with your phone, the system handling your call controls the power level at which your phone transmits.

Specific Absorption Rate (SAR)

Your mobile device is a radio transmitter and receiver. It is designed not to exceed the limits for exposure to radio waves recommended by international guidelines. These guidelines were developed by the independent scientific organization ICNIRP and include safety margins designed to assure the protection of all persons, regardless of age and health.

The guidelines use a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit for mobile devices is 2 W/kg and the highest SAR value for this device when tested at the ear was 0.566 W/kg*. As mobile devices offer a range of functions, they can be used in other positions, such as on the body as described in this user guide**. In this case, the highest tested SAR value is 1.048 W/kg.

As SAR is measured utilising the device’s highest transmitting power, the actual SAR of this device while operating is typically below that indicated above. This is due to automatic changes to the power level of the device to ensure it only uses the minimum level required to communicate with the network.

* The tests are carried out in accordance with

international guidelines for testing.

** Please see the section below about body worn

operation.

Body Worn Operation

Important safety information regarding radiofrequency radiation (RF) exposure:

• To ensure compliance with RF exposure guidelines the phone must be used with a minimum of 1.5 cm separation from the body.

• Failure to observe these instructions could result in your RF exposure exceeding the relevant guideline limits.

SAFETY PRECAUTIONS 5

Limiting Exposure to Radiofrequency (RF) Fields

For individuals concerned about limiting their exposure to RF fields, the World Health Organisation (WHO) provides the following advice:

• Precautionary measures: Present scientific information does not indicate the need for any special precautions for use of mobile phones. If individuals are concerned, they might choose to limit their own or their children’s RF exposure by limiting the length of calls, or using ‘handsfree’ devices to keep mobile phones away from the head and body.

• For further information readers are referred to: http://www.who.int/

6 SAFETY PRECAUTIONS

FCC Notice

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received,

including interference that may cause undesired

operation. Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user’s authority to operate the equipment.

Exposure to Radio Waves

THIS MODEL PHONE MEETS THE GOVERNMENT’S REQUIREMENTS FOR EXPOSURE TO RADIO WAVES.

Your wireless phone is a radio transmitter and receiver. It is designed and manufactured not to exceed the emission limits for exposure to radio frequency (RF) energy set by the Federal Communications Commission of the U.S. Government. These limits are part of comprehensive guidelines and establish permitted levels of RF energy for the general population. The guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons, regardless of age and health.

The exposure standard for wireless mobile phones employs a unit of measurement known as the Specific Absorption Rate, or SAR. The SAR limit set by the FCC is 1.6 W/kg.* Tests for SAR are conducted using standard operating positions specified by the FCC with the phone transmitting at its highest certified power level in all tested frequency bands. Although the SAR is determined at the highest certified power level, the actual SAR level of the phone while operating can be well below the maximum value. This is because the phone is designed to operate at multiple power levels so as to use only the power required to reach the network. In general, the closer you are to a wireless base station antenna, the lower the power output. Before a phone model is available for sale to the public, it must be tested and certified to the FCC that it does not exceed the limit established by the government-adopted requirement for safe exposure. The tests are performed in positions and locations (e.g., at the ear and worn on the body) as required by the FCC for each model. The highest SAR value for this model phone when tested for use at the ear is 0.949 W/kg and when worn on the body, as described in this user guide, is 0.592 W/kg. Body-worn Operation; This device was tested for typical body-worn operations with the back of the phone kept 1.5 cm from the body. To maintain compliance with FCC RF exposure requirements, use

accessories that maintain a 1.5 cm separation distance between the user’s body and the back of the phone. The use of belt-clips, holsters and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements, and should be avoided. While there may be differences between the SAR levels of various phones and at various positions, they all meet the government requirement for safe exposure. The FCC has granted an Equipment Authorization for this model phone with all reported SAR levels evaluated as in compliance with the FCC RF emission guidelines. SAR information on this model phone is on file with the FCC and can be found under the Display Grant section of http://www.fcc.gov/oet/fccid after searching on FCC ID APYHRO00058. Additional information on Specific Absorption Rates (SAR) can be found on the Cellular Telecommunications & Internet Association (CTIA) web-site at http://www.phonefacts.net. * In the United States and Canada, the SAR limit for

mobile phones used by the public is 1.6 watts/kg (W/ kg) averaged over one gram of tissue. The standard incorporates a substantial margin of safety to give additional protection for the public and to account for any variations in measurements.

SAFETY PRECAUTIONS 7

INFORMATION ON PROPER

Attention: Your product is marked with this symbol.

It means that used electrical and electronic products should not be mixed with general household waste. There is a separate collection system for these products.

DISPOSAL

A. Information on Disposal for Users (private

households)

1. In the European Union

Attention: If you want to dispose of this equipment,

Used electrical and electronic equipment must be treated separately and in accordance with legislation that requires proper treatment, recovery and recycling of used electrical and electronic equipment.

Following the implementation by member states, private households within the EU states may return

8 SAFETY PRECAUTIONS

please do not use the ordinary dust bin!

their used electrical and electronic equipment to designated collection facilities free of charge*. In some countries* your local retailer may also take back your old product free of charge if you purchase a similar new one.

*) Please contact your local authority for further details. If your used electrical or electronic equipment has

batteries or accumulators, please dispose of these separately beforehand according to local requirements.

By disposing of this product correctly you will help ensure that the waste undergoes the necessary treatment, recovery and recycling and thus prevent potential negative effects on the environment and human health which could otherwise arise due to inappropriate waste handling.

2. In other Countries outside the EU

If you wish to discard this product, please contact your local authorities and ask for the correct method of disposal.

For Switzerland: Used electrical or electronic

equipment can be returned free of charge to the dealer, even if you don’t purchase a new product. Further collection facilities are listed on the homepage of www.swico.ch or www.sens.ch.

B. Information on Disposal for Business Users

1. In the European Union

If the product is used for business purposes and you want to discard it:

Please contact your SHARP dealer who will inform you about the take-back of the product. You might be charged for the costs arising from take-back and recycling. Small products (and small amounts) might be taken back by your local collection facilities.

For Spain: Please contact the established collection

2. In other Countries outside the EU

If you wish to dispose of this product, please contact your local authorities and ask for the correct method of disposal.

system or your local authority for takeback of your used products.

DISTRACTIONS

Driving

Full attention must be given to driving at all times in order to reduce the risk of an accident. Using a phone while driving (even with a handsfree kit) causes distraction and can lead to an accident. You must comply with local laws and regulations restricting the use of wireless devices while driving.

Operating Machinery

Full attention must be given to operating the machinery in order to reduce the risk of an accident.

PRODUCT HANDLING

General Statement on Handling and Use

You alone are responsible for how you use your phone and any consequences of its use.

• You must always switch off your phone wherever the use of a phone is prohibited. Use of your phone is subject to safety measures designed to protect users and their environment.

• Always treat your phone and its accessories with care and keep it in a clean and dust-free place.

• Do not expose your phone or its accessories to open flames or lit tobacco products.

• Do not expose your phone or its accessories to liquid, moisture or high humidity.

• Do not drop, throw or try to bend your phone or its accessories.

• Do not use harsh chemicals, cleaning solvents, or aerosols to clean the device or its accessories.

• Do not paint your phone or its accessories.

SAFETY PRECAUTIONS 9

• Do not attempt to disassemble your phone or its accessories. Only authorised personnel must do so.

• Please check local regulations for disposal of electronic products.

• Do not carry your phone in your back pocket as it could break when you sit down.

Small Children

Do not leave your phone and its accessories within the reach of small children or allow them to play with it.

They could hurt themselves or others, or could accidentally damage the phone.

Your phone contains small parts with sharp edges that may cause an injury or which could become detached and create a choking hazard.

Demagnetisation

To avoid the risk of demagnetisation, do not allow electronic devices or magnetic media close to your phone for a long time.

Electrostatic Discharge (ESD)

Do not touch the SIM card’s metal connectors.

10 SAFETY PRECAUTIONS

Antenna Care

Do not cover the built-in antenna (p. 24, No. 20) with your hand when using the phone as this may interfere with the performance. If you cover it, call quality may deteriorate, and may shorten talk and standby times because the mobile phone has to operate on a higher power level than is necessary.

Normal Use Position

When placing or receiving a phone call, hold your phone to your ear, with the bottom towards your mouth or as you would a fixed line phone.

Air Bags

• Do not place a phone in the area over an air bag or in the air bag deployment area.

• Store the phone safely before driving your vehicle.

Seizures/Blackouts

If your phone is capable of producing bright flashing lights, please be careful because it may trigger seizures or blackouts.

Repetitive Motion Injuries

To minimise the risk of RSI (Repetitive strain injury), when texting or playing games with your phone:

• Do not grip the phone too tightly.

• Press the buttons lightly.

• Make use of the special features in the handset which minimise the number of buttons which have to be pressed, such as message templates and predictive text.

• Take lots of breaks to stretch and relax.

Emergency Calls

This phone, like any wireless phone, operates using radio signals, which cannot guarantee connection in all conditions. Therefore, you must never rely solely on any wireless phone for emergency communications.

Loud Noise

This phone is capable of producing loud noises which may damage your hearing.

Bright Light

If your phone is capable of producing a bright light, do not use it too close to the eyes.

Phone Heating

Your phone may become warm during charging and during normal use.

ELECTRICAL SAFETY

Accessories

• Use your phone only with batteries, chargers and accessories recommended by the manufacturer. The manufacturer disclaims any liability for damage caused by the use of other chargers, batteries or accessories.

• Before connecting the phone with a PC or a peripheral unit, read the operation manual for the other unit carefully.

• Do not touch the battery terminals. Batteries can cause damage, injury or burns if a conductive material touches exposed terminals. When the battery is detached from the phone, use a cover made of non-conductive material for keeping and carrying the battery safely.

SAFETY PRECAUTIONS 11

Connection to a Car

Seek professional advice when connecting a phone interface to the vehicle electrical system.

Faulty and Damaged Products

• Do not attempt to disassemble the phone or its accessory.

• Only qualified personnel must service or repair the phone or its accessory.

• If your phone or its accessory has been submerged in water, punctured, or subjected to a severe fall, do not use it until you have taken it to be checked at an authorised service centre.

INTERFERENCE

General Statement on Interference

Care must be taken when using the phone in close proximity to personal medical devices, such as pacemakers and hearing aids.

12 SAFETY PRECAUTIONS

Pacemakers

Pacemaker manufacturers recommend that a minimum separation of 15 cm be maintained between a mobile phone and a pacemaker to avoid potential interference with the pacemaker. To achieve this, use the phone on the opposite ear to your pacemaker and do not carry it in a breast pocket.

Hearing Aids

• People with hearing aids or other cochlear implants may experience interfering noises when using wireless devices or when one is nearby.

• Since the level of interference will depend on the type of hearing device and the distance from the interference source, increasing the separation between them may reduce the interference. You may also consult your hearing aid manufacturer to discuss alternatives.

Medical Devices

Please consult your doctor and the device manufacturer to determine if operation of your phone may interfere with the operation of your medical device.

Hospitals

Switch off your wireless device when requested to do so in hospitals, clinics or health care facilities. These requests are designed to prevent possible interference with sensitive medical equipment.

Aircraft

Switch off your wireless device whenever you are instructed to do so by airport or airline staff.

Interference in Cars

Please note that because of possible interference to electronic equipment, some vehicle manufacturers forbid the use of mobile phones in their vehicles unless a handsfree kit with an external antenna is included in the installation.

EXPLOSIVE ENVIRONMENTS

Petrol Stations and Explosive Atmospheres

• In locations with potentially explosive atmospheres,

obey all posted signs to turn off wireless devices such as your phone or other radio equipment.

• Areas with potentially explosive atmospheres

include fuelling areas, below decks on boats, fuel or chemical transfer or storage facilities, areas where the air contains chemicals or particles, such as grain, dust, or metal powders.

Blasting Caps and Areas

To avoid interfering with blasting operations, turn off your mobile phone or wireless device when in a blasting area or in areas posted “turn off two-way radios or electronic devices”.

SAFETY PRECAUTIONS 13

CONDITIONS OF USE

Battery

• Network configuration and phone usage will

affect talk-time and standby time.

Using the games or camera will hasten battery consumption.

• When the battery charging alert is displayed on the screen, charge the battery as soon as possible. If you continue using your phone ignoring the alert, the phone may cease to function, and all data and settings you have stored may be lost.

• Before removing the battery from the phone, make sure the phone is switched off.

• Replace and charge the new battery as soon as possible after removing the old one.

• Recommended temperature for using and storing batteries is approximately 20°C.

• The batteries’ performance is limited in low temperatures, particularly below 0°C and the phone may not work temporarily regardless of the amount of remaining battery power.

• The battery can be charged and discharged hundreds of times but it will eventually wear out. When the operating time (talk-time and standby time) is noticeably shorter than normal, it is time to buy a new battery.

14 CONDITIONS OF USE

RISK OF EXPLOSION IF BATTERY IS REPLACED

DISPOSE OF USED BATTERIES ACCORDING

CAUTION

BY AN INCORRECT TYPE,

TO THE INSTRUCTIONS

See “Battery Disposal” on page 26.

Memory Card

• Do not remove or insert a memory card while data on the card is being edited. Do not turn off the phone or device containing the memory card while data on the card is being edited as this may damage the data or cause the card to stop functioning correctly.

• Data may be lost under the following circumstances.

- If the phone is dropped or shaken or if force is

applied while the memory card is inserted.

- If the phone is used in areas that are exposed to

static electricity or electric noise.

• Back up your important data in the case data on the memory card is lost due to malfunctions.

• Do not touch the metal terminals with your hands or metal objects.

• Do not bend the memory card or subject it to violent impact. Keep it away from water and high temperatures.

• SHARP holds no responsibility for the loss or damage of data contained on a memory card.

• Keep all memory cards out of the reach of small children.

• Be sure to insert the memory card in the correct direction and orientation.

Camera Operation

• Learn picture quality, file formats, etc. beforehand. The taken pictures can be saved in JPEG format.

• Be careful not to move your hand while taking pictures. If the phone moves while taking a picture, the picture can become blurred. When taking a picture, hold the phone firmly to prevent it from moving, or use the delay timer.

• Clean the lens cover before taking a picture. Fingerprints, oils, etc. on the lens cover hinder clear focusing. Wipe them off with a soft cloth before taking a picture.

Others

• As with any electronic storage unit, data may be lost or corrupted under various circumstances.

• If the phone’s battery has been removed for some time, or the phone has been reset, the unit’s clock and calendar may be reinitialised. The date and time should be updated in this case.

• Use only specified handsfree kits (supplied or optional). Some phone’s functions may not work when unauthorised handsfree kit is used.

CONDITIONS OF USE 15

Introduction ................................................. 1

Useful Functions and Services .................... 3

SAFETY PRECAUTIONS ............................. 4

RADIOFREQUENCY (RF) EXPOSURE INFORMATION ON PROPER

DISPOSAL .................................................. 8

DISTRACTIONS ........................................ 9

PRODUCT HANDLING ............................ 9

ELECTRICAL SAFETY .......................... 11

INTERFERENCE ..................................... 12

EXPLOSIVE ENVIRONMENTS ............. 13

CONDITIONS OF USE ............................... 14

List of Menu Functions ............................. 19

Your Phone ................................................ 21

Optional Accessories ................................. 21

Getting Started .......................................... 22

Inserting the SIM Card and the Battery .... 25

Charging the Battery ................................. 27

Inserting/Removing the Memory Card ..... 28

Connecting the Handsfree Kit ................... 29

Turning Your Phone On and Off ............... 29

16 Table of Contents

Display Indicators (Main Display) ............ 30

Display Indicators (External Display) ....... 32

Navigating Functions ................................33

..... 5

Call Functions ............................................34

Making a Call ............................................ 34

Speed Dialling ........................................... 34

Redialling ...................................................35

Answering a Call ....................................... 35

Incall Menu ................................................ 36

Entering Characters ..................................40

Changing the Input Languages .................. 40

Changing the Input Method ....................... 41

Using Text Templates ................................ 42

Using the Menu ..........................................43

Contacts .....................................................44

Contacts List .............................................. 44

Selecting the Storage Memory .................. 44

Changing the List Displayed ..................... 44

Changing the Name Order ......................... 45

Add New Contact ...................................... 45

Copying Contacts List Entries

between SIM Card and Handset ................46

Finding a Name and Number .....................46

Dialling from the Contacts List ................. 47

Editing Contacts List Entries .....................47

Deleting Contacts List Entries ...................47

Viewing Groups ......................................... 47

Group Call .................................................48

Assigning a Ringtone to

Each Contacts List Entry ...........................49

Memory Status ...........................................49

Speed Dial List .......................................... 49

Sending a Contacts List Entry ................... 50

Receiving a Contacts List Entry ................50

Dialling a Service Phone Number ............. 51

Call Log .....................................................52

Speed Dial List .......................................... 53

My Numbers ..............................................53

Call Timers ................................................53

Data Counter .............................................. 53

Call Costs ................................................... 54

Camera ....................................................... 55

Take Picture ...............................................55

Record Video .............................................60

Messages ................................................... 64

Multimedia (MMS) ....................................64

Text (SMS) .................................................70

Email ..........................................................73

Alert Inbox .................................................74

Cell Broadcasts ..........................................75

Vodafone live! ............................................ 76

Starting the WAP Browser .........................76

Navigating a WAP Page ............................77

My Items .....................................................80

Pictures .......................................................80

Games & More ...........................................82

Sounds ........................................................83

Videos ........................................................85

Text Templates ...........................................88

Memory Status ...........................................88

Games & More ........................................... 89

Applications ...............................................89

Screensavers ...............................................90

More Games ...............................................90

Settings .......................................................91

Java™ Information .....................................92

Table of Contents 17

Applications ............................................... 93

SIM Application ........................................ 93

Calendar .................................................... 93

Alarms ....................................................... 96

Calculator .................................................. 97

Voice Recorder .......................................... 98

Phone Help ................................................ 99

Music Player ............................................ 100

Settings .................................................... 102

Connectivity ............................................ 102

Profiles .................................................... 105

Setting the Display .................................. 112

Sound ....................................................... 115

Call Settings ............................................ 115

Date & Time ............................................ 120

Changing the Language ........................... 121

Network ................................................... 121

Security .................................................... 125

Master Reset ............................................ 126

Connecting GX34 to Your PC ................. 127

System Requirements .............................. 127

GSM/GPRS Modem ................................ 127

Handset Manager ..................................... 130

18 Table of Contents

Troubleshooting ......................................131

Index .........................................................134

List of Menu Functions

GX34 functions are listed below. See relevant page for details of each function. The menu’s corresponding number is used for shortcuts. For details, see page 43.

1 Games & More

2 Vodafone live!

3 Applications

4 Messages

5 Camera

1 Applications (p. 89) 2 Screensavers (p. 90) 2 Games & More (p. 82) 3 More Games (p. 90) 3 Sounds (p. 83) 4 Settings (p. 91) 4 Videos (p. 85) 5 Java™ Information (p. 92) 5 Text Templates (p. 88) 1 Vodafone live! (p. 76) 6 Bookmarks - 2 Games - 7 Memory Status (p. 88) 3 Ringtones - 4 Pictures - 2 My Music (p. 100) 5 News - 3 Playlist (p. 101) 6 Spor t - 7 Find & Seek - 2 Call Log (p. 52) 8 Chat - 3 Speed Dial List (p. 53) 9 Search - 4 My Numbers (p. 53) 1 SIM Application 2 Calendar (p. 93) 6 Data Counter (p. 53) 3 Alarms (p. 96) 4 Calculator (p. 97) 5 Voice Recorder (p. 98) 6 Phone Help (p. 99) 2 Profiles (p. 105) 1 Create Message (p. 64, 71, 73) 3 Display (p. 112) 2 Multimedia (p. 64) 4 Sound (p. 115) 3 Text (p. 70) 5 Call Settings (p. 115) 4 Email (p. 73) 6 Date & Time (p. 120) 5 Alert Inbox (p. 74) 7 Language (p. 121) 6 Media Album - 8 Network (p. 121) 7 Vodafone Mail - 9 Security (p. 125) 8 Cell Broadcasts (p. 75) 0 Master Reset (p. 126) 9 Area Info - 1 Take Picture (p. 55) 2 Record Video (p. 60)

(p. 93) 5 Call Timers (p. 53)

6 My Items

7 Music Player

8 Contacts

9 Settings

* Depends on SIM card contents.

1 Pictures (p. 80)

1 Last Played Music (p. 100)

1 Contacts List (p. 44)

7 Call Costs 8 Service Dialling No. 1 Connectivity (p. 102)

(p. 54) (p. 51)

List of Menu Functions 19

Note for the menu references for the Postcard and Media Album services

• The menu references for the Postcard and Media Album services vary in the United Kingdom and Ireland as follows:

Current

references in

the User Guide

“Postcard” “live! Postcard” (Not available)

“As Postcard” “As live! Postcard” (Not available)

“State/Province” “ County” “State/Province”

“Media Album” “live! Studio” “Picture Album”

“To Album” “To live! Studio” “To Picture Album”

References in

United Kingdom

References in

Ireland

20 List of Menu Functions

Your Phone

Please check the following carefully. Your phone should come complete with:

• GSM 900/1800/1900 GPRS phone

• Rechargeable Li-ion Battery

• AC Charger

• Stereo Handsfree

•CD-ROM

•User Guide

• Quick Start Guide* * This item is not provided in some areas.

Optional Accessories

• Li-ion Spare Battery (XN-1BT33)

• Cigarette Lighter Charger (XN-1CL30)

• USB Data Cable (XN-1DC30)

• AC Charger (XN-1QC30, XN-1QC31)

• Handsfree Microphone Unit (XN-1HU90)

• Stereo Headset (XN-1HS90)

The above accessories may not be available in all regions.

For details, please contact your dealer.

Your Phone 21

Getting Started

22 Getting Started

11 12

1. Earpiece/Speaker

2. Navigation Keys (Arrow Keys):

Up/Down arrow keys: a b Left arrow key:

Right arrow key:dDisplays list of Saved

3. Left Soft Key:

4. Send Key:

5. Centre Key:

6. Voice Mail Key:GPress and hold this key to

Moves cursor to select menu items, etc. Displays Contacts List entries in standby mode. Displays list of Applications in standby mode.

Pictures in standby mode. Executes the function at the bottom left of the screen.

Makes or accepts calls, views the call logs in standby mode. Displays Main menu in standby mode and executes functions.

connect to the Voice mail centre automatically. (Depends on the SIM card.)

7. */Shift Key:

8. Main Display

9. Right Soft Key:C Executes the function at the

10.End/Power Key:FEnds a call, turns power on/

Switches character case among four modes: Abc, ABC, 123 and abc. Press and hold this key on the text entry screen to shift the text input method between multi-tap and T9 mode.

bottom right of the screen. Used to access “Vodafone live!” by opening the browser in standby mode.

off.

11.Keypad

Getting Started 23

12.#/Silent Key:

13.Microphone

14.External Display

15.Handsfree Kit/Microphone Connector

16.microSD Card Slot

17.External Connector:

18.Camera

19.Battery Cover

24 Getting Started

Switches symbol screens. Press and hold this key on the text entry screen to display the language options screen. Press and hold this key during standby to switch Profiles settings between Normal and Silent mode. Press e, then R during standby to turn the Bluetooth wireless function on or off.

Used to connect either the charger or USB Data Cable.

20.Built-in Antenna: Warning: Do not cover the

21.Side-Up/Side-Down Keys:

V W

hinge area of the phone with your hand when in use as this may interfere with the performance of the built-in antenna.

Moves cursor to select menu items, adjusts earpiece volume, etc.

Inserting the SIM Card and the

SIM card

Battery

1. Slide off the battery cover ( ).

3. Hold the battery so that the metal contacts of the

battery are facing down, slide the guides on the top of the battery into the battery slots , and then insert it .

2. Slide the SIM card into the SIM holder.

4. Replace the battery cover and slide it as shown

below.

Note

• Make sure that only 3V SIM cards are used.

• Make sure that the standard accessory battery (XN-1BT33) is used.

Getting Started 25

Removing the SIM Card and the Battery

1. Make sure to turn off your phone and disconnect the

charger and other accessories. Slide off the battery cover ( ).

3. Hold down gently while sliding the SIM card

out of the SIM holder .

2. Pick up the battery using the protruding edge and

remove the battery from the phone.

26 Getting Started

Battery Disposal

In order to protect the environment, please read the following points concerning battery disposal:

• Take the used battery to your local waste depot, dealer or customer service centre for recycling.

• Do not expose the used battery to an open flame, into water or dispose with the household waste.

Charging the Battery

You must charge the battery for at least 2 hours before using your phone for the first time.

Using the Charger

1. Open the cover of the external connector, and

connect the charger to the external socket located at the bottom of the phone until it clicks.

2. Connect the charger to an AC outlet.

When the phone is charging, the animated battery status icon ( ) in the upper right of the screen displays the current status. Standard charging time: Approx. 2 hours.

Note

• Charging time may vary depending on the state of the

battery and other conditions. (See “Battery” on page 14.)

To Disconnect the Charger

When charging is complete, the battery indicator icon displays the full charge status.

1. Unplug the charger from the AC outlet.

2. Push and hold the side buttons of the charger ,

then disconnect the charger from the external socket of the phone . Close the cover.

Note

• Do not use any non-approved chargers as they may

damage your phone and invalidate any warranties, see “Battery” on page 14 for details.

• Forcibly disconnecting the charger may cause

malfunction.

Getting Started 27

To Charge Using the Cigarette Lighter Charger

The optional Cigarette Lighter Charger supplies power for charging from the cigarette lighter socket of a car.

Battery Level Indicator

The current battery level is displayed in the upper right corner of the main display and in the external display.

Low Battery During Use

When the battery is running low, an alarm will sound and “ ” is displayed on the main display and the external display.

If you are using your phone and you hear the “low battery” alarm, attach your charger as soon as possible. The phone may not be able to continue normal operation if you continue to use it. The battery may only last approximately five minutes before the phone itself powers down during a call.

Battery Indicators Charge Level

Sufficiently charged

Partially charged

Charging recommended

Charging required

Empty

28 Getting Started

Inserting/Removing the Memory Card

Note

• Make sure that the phone is turned off before inserting/removing the memory card.

• Be sure to insert the card in the correct direction and orientation.

• Keep all memory cards out of the reach of small children.

1. Turn off the phone.

2. Open the microSD card slot cover.

3. Insert the memory card until it clicks. (To remove

the memory card, push the memory card until it clicks.)

4. Close the cover.

Tip

• You see the following indicators when the memory card is in use:

:Appears when the card is inserted. :Appears when the card is damaged or unusable.

Make sure the card is properly inserted.

:Appears when the card is being written to or read

from.

:Appears when the card is being formatted.

Connecting the Handsfree Kit

1. Open the connector cover.

2. Connect the handsfree kit.

Turning Your Phone On and Off

To turn the power on, press and hold F for approximately 2 seconds.

The standby screen is displayed. To turn the power off, press and hold F for

approximately 2 seconds.

Getting Started 29

To Enter the PIN Code

Status indicators

Right soft key

Left soft key

Centre key

If the PIN (Personal Identification Number) code is enabled you are asked to enter the PIN code each time the phone is switched on. For details on setting the PIN code, see “Enabling/Disabling the PIN Code” on page 125.

1. Enter your PIN code.

2. Press e.

Note

• If your PIN code is entered incorrectly three times in a row, the SIM card is locked. See “Enabling/ Disabling the PIN Code” on page 125.

To Copy Contacts List from the SIM Card

When you insert the SIM card into your phone for the first time and start the Contacts List application, you are asked whether you wish to copy Contacts List entries on the SIM card. Follow the on-screen instructions, or you can do it later using the Contacts List menu as follows:

“Contacts” “Advanced” → “Copy All Entries”

→

“Contacts List” → [Options] →

1. Select “From SIM to Handset”.

Display Indicators (Main Display)

30 Getting Started

Status Indicators

1. / : Strength of received signal/Service out

of range

//:

GPRS within range and enabled/ Roaming outside network/GPRS within range, enabled and roaming

2. : Call incoming

3. : Call in progress

4. / : CSD/GPRS in progress

5. : Fax communication in progress

6. : “Diverts” (p. 115) set to “All Calls”

7. / : Secure WAP page displayed

8. / : Text message alerts [unread/mailbox

full]

9. / : Multimedia message alerts [unread/

mailbox full]

10. / : Email alerts [unread/mailbox full]

11. : USB Data Cable connected

12. / : Bluetooth wireless setting [enabled/ communicating]

13. / : Java™ application [executed (colour)/ suspended (grey)]

14. (No display)/////: Current profile [Normal/Meeting/ Activity/Car/Headset/Silent]

15. : T9 text input method enabled

16. / / / : Current text input method [First letter upper case/Upper case/Lower case/ Numeric]

17. : Memory card inserted

Getting Started 31

18. : Battery level

19. / / :“Ringer Volume” (p. 106) set to “Silent”/Vibration enabled (p. 107)/ Vibration enabled and sound deactivated

20. : Daily alarm enabled

21. / : Schedule entry enabled [with/without a reminder alarm]

22. : Outbox contains unsent multimedia messages

23. : WAP alert

24. : Voicemail message alert

32 Getting Started

Display Indicators (External Display)

Status Indicators

1. : Strength of received signal

2. : Battery level

3. : USB Data Cable connected

4. / :

Bluetooth

wireless connection [enabled/

communicating]

Navigating Functions

All applications are accessed from the Main menu. To open the Main menu, press the centre key (e) during standby.

To launch applications, you will need to highlight menu items, and make selections. To select a menu item (indicated in quotation marks), move the cursor using a, b, c and d, and press e to commit your selection.

In certain procedures, you will need to press one of the soft keys (indicated in square brackets), which are displayed at the bottom left and right of the screen. Press the corresponding soft key (A or C).

To return to the previous screen, press the right soft key if it displays “Back”. To close the Main menu, press the right soft key if it displays “Exit”.

Each section in this User Guide starts with a list of items you will need to select in order (indicated in italics) before performing the procedures shown. Select each item to reveal the next set of items that you have to select. Open subsection items after opening those listed in the main section.

Example:

“Contacts” → “Contacts List” → [Options] → “Advanced”

Navigating Functions 33

Call Functions

Making a Call

1. Enter the area code and the phone number you wish

to dial and press D to dial. If you enter the wrong number, press [Clear] to

delete the number to the left of the cursor.

Emergency Calls

1. Enter 112 (international emergency number) using

the keypad and press D to dial.

Note

• Emergency calls may not be available on all mobile

phone networks when certain network services and/ or phone features are in use. Contact your network operator for more information.

• This Emergency number can normally be used to

make an emergency call in any country, with or without a SIM card inserted, if a GSM network is within range.

34 Call Functions

International Calls

1. Press and hold Q until a “+” (international

dialling prefix) sign is displayed.

2. Enter the country code, followed by the area code

(without the leading zero) and the phone number, and press D to dial.

Speed Dialling

Up to 8 phone numbers from the Contacts List memory (Handset and SIM) can be assigned to speed dials. You can call the numbers using the digit keys (H to O).

For details on setting the Speed Dial List, see “Speed Dial List” on page 49.

1. To dial a number using the speed dial, press and

hold any of the digit keys (H to O). The phone number stored in the Speed Dial List is

dialled.

Redialling

You can redial numbers in the call log. Select from specific categories or “All Calls”. Specific category contains up to 10 numbers and the “All Calls” list contains up to 30.

1. Press D during standby.

2. Press c or d to switch logs between “All Calls”,

“Dialled Numbers”, “Missed Calls” and “Received Calls”.

3. Highlight the phone number you wish to call.

4. Press D to redial the call.

Automatic Redialling

This setting allows you to automatically redial the number if the first attempt was unsuccessful because the called party was busy.

If you wish to stop redialling, press F or [End].

To Set the Auto Redial Function

“Settings”

1. Select “On” or “Off”.

Note

• When you receive an incoming call, the Auto Redial

• Automatic redialling is not available for fax and data

→

“Call Settings” → “Auto Redial”

function is interrupted.

calls.

Answering a Call

When an incoming call is detected, the phone rings.

1. Press D, e or [Answer] to answer the call.

Or press any key except F and [Busy] when the “Any Key Answer” function is enabled. Set the Any Key Answer function in the profile of each mode. (p. 111)

Tip

• When the Personal Handsfree Kit (option) is connected to the phone, you can answer calls by pressing the Answer button.

• If you have subscribed to the Calling Line Identification (CLI) service and the caller’s network sends the number, the caller’s number is displayed on the screen. If the caller’s name and number are stored in the Contacts List, the caller’s name and phone number are displayed on the screen.

• If the number is a restricted number, the display shows “Withheld”.

• When receiving a call from the person whose picture is registered in the Contacts List, receiving display and the picture are displayed alternately.

Call Functions 35

Rejecting an Incoming Call

1. Press F or press and hold the side-up or side-down

key while the phone is ringing to reject a call you do not wish to answer.

Letting the Caller Know You are Unavailable

1. Press [Busy] while the phone is ringing to send a

busy tone to the caller of an incoming call letting them know that you cannot answer the call.

36 Call Functions

Incall Menu

Your phone has additional functions available while a call is in progress.

Adjusting the Earpiece Volume

During a call, you can adjust the earpiece volume (and handsfree volume, if connected).

1. During a call, press the side-up or side-down key to

display the Earpiece Volume screen.

2. Press the side-up key (or a/d) to increase the

volume of the call or press the side-down key (or b/c) to decrease the volume. Five levels (level 1 to 5) are selectable.

3. Press e when the volume is set to the desired level.

The phone returns to the incall screen automatically if left unused.

Putting a Call on Hold

This function allows you to manage two calls at the same time. If you wish to make another call while you are talking to someone, you can put the current call on hold to call someone else.

To Make Another Call during a Call

1. During a call, press [Options].

2. Select “Hold”.

The current call is put on hold. To retrieve a call, press [Options] and select “Retrieve”.

3. Enter the phone number you wish to make another

call to, then press D.

Tip

• You can also make another call by entering the phone number during a call instead of steps 1 and 2. The current call is automatically put on hold.

Call Waiting

This service notifies you of another incoming call while you have a call in progress.

1. During a call, press [Options] and select “Hold &

Answer” to answer the second call. The first call is put on hold and you can now talk to

the second caller.

2. Press [Options] and select “Swap Calls” to switch

between the two calls.

3. Press [Options] and select “Release Call” to end the

current call and return to the held call.

Note

• You need to set “Call Waiting” to “On” if you use the Call Waiting service (p. 116).

• Call Waiting service may not be available on all networks. Contact your network operator for more information.

• If you do not wish to answer the second call, press [Busy], or press [Options] and select “Busy” or “Reject”, in step 1. If “Reject” is selected, the call log of the second call is saved as a missed call.

Call Functions 37

Accessing SMS Menu During a Call

1. During a call, press [Options] and select “Text”.

The following options are available: “Create Message” to create an SMS, or “Inbox”, “Sent” or “Drafts” to access these folders. For details on SMS, see “Text (SMS)” on page 70.

Conference Call

Conference call is a call with more than 2 participants. You may include up to 5 participants in a conference call.

To Make a Conference Call

You must have one active call and one held call.

1. During a call, press [Options] and select

“Multiparty” to answer the second call.

2. Select “Conference All” to join the conference call.

3. Press F to end the conference call.

38 Call Functions

Note

• Conference call service may not be available on all networks. Contact your network operator for more information.

• To reject adding more participants to the current party, press [Options] and select “Reject”, or you can send the busy tone by selecting “Busy”.

• You have more options for the Conference call in step 2:

• To put all participants on hold, select “Conference

Hold All”.

• To put all participants except the current call on

hold, select “Private”.

• To end the call with all participants, select

“Release All”.

• To disconnect from the conference call but still

allow the other participants to continue talking together, select “Transfer”.

• To put the current call on hold and continue to

have a conference call with the remaining participants, select “Exclude”.

To Add New Participants to the Conference Call

1. Press [Options] and select “Dial”.

2. Enter the number you wish to include in the

conference call and press D to dial.

3. Press [Options] and select “Multiparty”.

4. Select “Conference All” to join the conference call.

If you wish to add other participants, repeat steps 1 to 4.

To End the Call with a Conference Call Participant

1. During a conference call, highlight the person that

you wish to disconnect from the conference call.

2. Press [Options] and select “Release Call”.

To Have a Private Conversation with One of the Participants

If you wish to have a private conversation with one of the participants, you may select the participant from the conference list and put the other participants on hold.

1. During a conference call, select the person that you

wish to talk to.

2. Press [Options] and select “Multiparty”.

3. Select “Private”.

4. Once you have finished the private conversation,

press [Options] and select “Multiparty”.

5. Select “Conference All” to return to the conference

call.

Muting the Microphone

1. During a call, press [Mute] to mute the microphone.

To unmute the microphone, press [Unmute].

Call Functions 39

Entering Characters

When entering characters to create Contacts List entries, text messages or multimedia messages, etc., press the corresponding keys.

In multi-tap input method, press each key until the desired character is displayed. For example, press H once for the letter “A” or twice for the letter “B”.

Press the following keys to:

enter:

. (full-stop) , (comma) - (hyphen) ? ! ’ (apostrophe) @ :1

enter:

(space)+ = < > € £ $ ¥ % &0 switch character case among four modes:

Abc, ABC, 123 and abc. enter other characters.

Changing the Input Languages

You can change the input language on the text entry screen.

1. On the text entry screen, press [Options].

2. Select “Input Language”.

If “Input Language” is not displayed, select “Text Options” and then select “Input Language”.

3. Select the desired language.

Tip

• You can press and hold R instead of steps 1 and 2 to display the language options screen.

Press and hold the following keys to:

G-O

enter 0 - 9 numbers.

shift between multi-tap and T9 mode.

P R

40 Entering Characters

display the language options screen.

Changing the Input Method

T9 Text Input

T9 text input method is a shortcut to enter text easily and quickly.

1. On the text entry screen, press and hold P to enter

T9 mode.

2. Press [Options].

3. Select “Input Method”.

If “Input Method” is not displayed, select “Text Options” and then select “Input Method”.

4. Select the input mode (Abc, ABC, abc, 123).

5. Press each key once for any letter you require on

that key. To enter the word “How”, press J L O.

6. If the word shown isn’t the one you want, press a

or b until you highlight the correct one.

7. Press e to select the word.

Note

• If the correct word is not shown in step 6, enter the

correct word again after switching to the multi-tap input method.

Tip

• If you press Q instead of step 7, a space is inserted

next to the selected word.

Symbols and Punctuations

1. On the text entry screen, press [Options].

2. Select “Add Symbol”.

If “Add Symbol” is not displayed, select “Text Options” and then select “Add Symbol”.

3. Select the desired symbol.

My Dictionary

You can create your own word list for T9 text input.

1. On the text entry screen in T9 mode, press

[Options].

2. Select “My Dictionary”.

If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

3. Select “Add New Word” and enter a new word.

Entering Characters 41

To edit a word in the list

1. On the text entry screen in T9 mode, press

[Options].

2. Select “My Dictionary”.

If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

3. Highlight the desired word.

4. Press [Options] and select “Edit”.

5. Modify the word.

Tip

• You can also carry out the following steps to register a new word in the list for T9 text input.

1. Enter a (part of) word in T9 mode you wish to

2. Press [Options].

3. Select “My Dictionary”.

If “My Dictionary” is not displayed, select “Text Options” and then select “My Dictionary”.

4. Modify the word.

42 Entering Characters

Using Text Templates

You can use the sentences registered in Text Templates when entering characters.

For details on creating the text template, see “Adding Phrases to Text Templates” on page 88.

1. On the text entry screen, move the cursor to the

point you wish to insert the template.

2. Press [Options].

3. Select “Add Text Template”.

If “Add Text Template” is not displayed, select “Text Options” and then select “Add Text Template”.

4. Select the desired text template.

The selected text template is inserted.

Using the Menu

Accessing Applications

1. Press e during standby.

The Main menu is displayed.

2. Navigate to required location.

3. Press e to access function.

Shortcut Keys

You can shortcut to the specified menus by pressing e and digit keys for the menu’s corresponding number on the Main menu. See the List of Menu Functions on page 19 for reference.

Shortcuts are listed in the headings of this manual. For example: “M 9-7”.

Example: To Access “Language” Sub Menu

Note

• The shortcut keys work for the first three menu levels

Using Shortcut Keys

Press e O M.

only.

Using the Menu 43

Contacts

(M 8)

(M 8-1)

Contacts List

You can store the phone numbers and Email addresses of your friends, family and colleagues in the Contacts List.

Depending on the size of the entry, your phone can store up to approximately 500 entries. In a Contacts List, you can store the following items.

Items stored in the handset memory

First Name Last Name Tel Mobile Tel Private Tel Office Email Private Email Business Group Address (Street & Number, Postal Code, City, State/ Province, Country) Note

44 Contacts

Items stored in the SIM memory

Name: The number of characters that can be

Phone: Up to 40 digits Using the Bluetooth wireless function, you can send the

Contacts List to a PC and save to prevent loss.

stored differs depending on the SIM card you use.

Selecting the Storage Memory

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Save New Contacts”

1. Select Contacts location from “To Handset”, “To

SIM” or “Choose before Saving”.

Tip

• “Choose before Saving” prompts you to choose the memory every time you save a new entry.

Changing the List Displayed

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Contacts Location”

1. Select from “Handset Memory”, “SIM Memory” or

“Both”.

Changing the Name Order

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Name Order”

1. Select from “First - Last name” or “Last - First

name”.

Add New Contact

You can choose either the phone or SIM card memory locations to store the new entry. For switching locations, see “Selecting the Storage Memory” on page 44.

The amount of phone numbers that you can store to the SIM card is dependent on its capacity. Contact your network operator for details.

“Contacts”

If you select the “Choose before Saving” option for the memory to be used, the selection is between “To Handset” and “To SIM”.

1. Select the field you wish to fill in, and enter the

2. Press [Save] when finished.

→

“Contacts List” → “Add New Contact”

relevant information.

Tip

• To create an entry, at least one field must be filled. If

you create a new entry on the SIM card, you need to enter a phone number.

Adding a Thumbnail to Entries

Only Contacts saved to the handset can have Thumbnails attached to them.

“Contacts” → “Contacts List”

1. Highlight the desired handset entry.

2. Press [Options] and select “Edit/Add Details”.

3. Press [Options] and select “Picture”.

4. Select the desired picture.

5. Press [Save] when finished.

Note

• From the Contacts List entry that has a thumbnail

added, you can change or delete it by selecting “Change” or “Remove” after step 3.

• If you delete a picture in Saved Pictures, the

corresponding thumbnail is also deleted.

Contacts 45

Copying Contacts List Entries between SIM Card and Handset

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Copy All Entries”

1. Select “From SIM to Handset” or “From Handset to

SIM”. The confirmation screen appears automatically, asking you if you wish to copy or not.

Note

• When you insert the SIM card into your phone for the first time and start the Contacts List application, the confirmation screen appears automatically, asking you if you wish to copy or not. The number of Contacts List entries to be copied varies depending on the SIM capacity.

46 Contacts

Copying a Single Entry from Handset to SIM Card

“Contacts”

→

“Contacts List”

1. Select the desired entry.

2. Highlight the desired phone number.

3. Press [Options] and select “Copy to SIM”.

Finding a Name and Number

“Contacts” → “Contacts List”

1. Enter the first few letters of the name.

Search results are displayed in alphabetical order.

Tip

• You can select the Contacts location from “Handset Memory”, “SIM Memory” or “Both” before searching.

• To view the details of the item such as address, highlight the desired item, press [Options] and select “View”.

Dialling from the Contacts List

“Contacts” → “Contacts List”

1. Highlight the desired entry and press D.

Tip

• If more than one phone number is registered for the entry, select the desired phone number after step 1 and press D. You can also dial the desired phone number by pressing the digit key corresponding to the position the entry is on the list.

• You can also dial from the details screen of the Contacts List. On the details screen, select the desired phone number and press D.

Editing Contacts List Entries

“Contacts” → “Contacts List” → [Options] → “Edit/ Add Details”

1. Select the field you wish to edit, and modify the

information.

2. Press [Save] when finished.

Deleting Contacts List Entries

Deleting All Contact Entries

“Contacts” “Advanced” → “Delete All Entries”

→

“Contacts List” → [Options] →

1. Enter your handset code.

2. Select “Handset Entries” or “SIM Entries”.

The confirmation screen appears automatically, asking you if you wish to delete or not. The default handset code is “0000”. For details on changing the handset code, see “To Change Handset Code” on page 126.

Deleting a Contact Entry

“Contacts”

→

“Contacts List”

1. Highlight the desired entry.

2. Press [Options] and select “Delete”.

Viewing Groups

You can set group icons when storing Contacts entries so that you can easily find and edit them.

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Group” → “View Groups”

1. Select the desired group.

“ ” appears next to the selected group. Select the group again to cancel, and the checkbox becomes unchecked.

Contacts 47

Note

• This menu is available when the Contacts location is set to “Handset Memory”.

Tip

• Press [Options] and select “Current Only” to view only the selected group or “Select All” to view all groups.

Group Call

Different ringtones can be set for each group. When you purchase this phone, groups are set to off. If you do not set a group ringtone, the ringtone assigned in the Settings menu is used.

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Group” → “Group Call”

1. Select the desired group.

2. Select “Switch On/Off”.

3. Select “On” or “Off”.

4. Select “Assign Ringtone”.

48 Contacts

5. Select “Preset Sounds” or “My Sounds”.

6. Select the desired ringtone.

For details on selecting a ringtone, see “Assigning Ringtone” on page 107.

7. Select “Vibration” and select from “On” or “Off”.

For details on selecting a vibration, see “Vibration” on page 107.

8. Press [OK].

Note

• This menu is available when the Contacts location is set to “Handset Memory”.

Assigning a Ringtone to Each Contacts List Entry

A specified ringtone or vibration setting can be associated to a pre-registered entry.

“Contacts” → “Contacts List”

1. Select the desired entry.

2. Press [Options] and select “Edit/Add Details”.

3. Press [Options] and select “Ringtone”.

4. Select “Switch On/Off”.

5. Select “On” or “Off”.

6. Select “Assign Ringtone”.

7. Select “Preset Sounds” or “My Sounds”.

8. Select the desired ringtone.

For details on selecting a ringtone, see “Assigning Ringtone” on page 107.

9. Select “Vibration” and select from “On” or “Off”.

For details on selecting a vibration, see “Vibration” on page 107.

10.Press [OK].

11.Press [Save].

Memory Status

This function helps you to check the memory used in the Contacts List.

“Contacts” → “Contacts List” → [Options] → “Advanced” → “Memory Status”

Speed Dial List

You can set a maximum of 8 phone numbers in the Speed Dial List (p. 53).

Setting Contacts List Entries in the Speed Dial List

“Contacts” → “Contacts List”

1. Select the desired entry.

2. Highlight the desired phone number.

3. Press [Options] and select “Add to Speed Dial”.

4. Select the desired list number.

Tip

• The nine digit keys correspond to list numbers.

• To view the speed dial list, see page 53.

Contacts 49

Sending a Contacts List Entry

“Contacts” → “Contacts List”

1. Highlight the desired entry.

Press [Options] and select “Send Contact”.

3. Select “Via Bluetooth”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry is sent.

Note

• When pairing, you need to enter your passcode when establishing contact with a Bluetooth wireless technology enabled device for the first time except when “Authentication” (p. 104) is set to “Off”.

Tip

• You can send your own Contacts List entry. Highlight “My Card” in step 1. For details on storing your information in My Card, see “Registering Your Information as a Contacts List Entry” on page 51.

50 Contacts

Receiving a Contacts List Entry

When the phone receives a Contacts List entry, a confirmation message appears.

1. Press [Yes].

The received entry is registered in the Contacts List. Press [No] to reject.

Tip

• For details on making Bluetooth wireless settings, see “Connectivity” on page 102.

Registering Your Information as a Contacts List Entry

You can store your information in the Contacts List.

“Contacts”

→

“Contacts List” → “My Card”

1. Press [Options] and select “Edit/Add Details”.

2. Select the field you wish to fill in, and enter the

relevant information.

3. Press [Save] when finished.

Dialling a Service Phone Number

Certain SIM cards contain service phone numbers that can be dialled. Contact your SIM card vendor for more information. On the Contacts screen, “Service Dialling No.” is displayed at the bottom of the list.

“Contacts”

1. Select “Service Dialling No.”.

2. Select the desired service phone number.

Tip

• If the SIM card contains only one service phone

number, you can dial it in step 1 by pressing e.

• If no service phone number is stored in the SIM card,

this menu is not displayed.

Contacts 51

Call Log

(M 8-2)

The phone will record the last 10 missed calls, received calls and dialled numbers.

Viewing Call Log

“Contacts”

1. Press c or d to switch logs between “All Calls”,

2. Select the phone number you wish to view.

Tip

• You can also confirm call logs by pressing D during

52 Contacts

→

“Call Log”

“Dialled Numbers”, “Missed Calls” and “Received Calls”. The selected call log list is displayed.

If you wish to dial the number, press D.

standby mode.

Sending Messages

1. In call log list, highlight the call log you wish to

send a message to.

2. Press [Options] and select “Create Message”.

3. Select “Multimedia”, “Text” or “Postcard”.

For details on creating a message, see “Creating a New MMS” on page 64 or “Creating and Sending a New SMS” on page 71.

Note

• The Postcard service is not available with some service providers. Please contact your service provider for more information.

Deleting a Call Log

1. In call log list, highlight the call log you wish to

delete.

2. Press [Options] and select “Delete”.

Speed Dial List

(M 8-3)

(M 8-4)

(M 8-5)

(M 8-6)

You can view and perform other operations for phone numbers registered in the Speed Dial List.

“Contacts” → “Speed Dial List”

The names and phone numbers stored in the Speed Dial List are displayed in order.

My Numbers

You can check your own voice, data and fax phone numbers.

“Contacts” → “My Numbers”

1. Select the phone number you wish to check from

“Voice”, “Data” or “Fax”.

Note

• “Data” or “Fax” may not be displayed depending on the SIM card.

Call Timers

This function lets you check the duration of your calls.

Checking the Duration of the Last Call and All Calls

“Contacts”

→

“Call Timers”

1. Select “Received Calls” or “Dialled Numbers”.

The duration of the last call and all calls are displayed.

Resetting All Call Timers

“Contacts”

→

“Call Timers” → “Clear Timers”

Data Counter

You can confirm the amount of bytes that you used in the GPRS transmission.

“Contacts” → “Data Counter”

1. Select from “Last Data” or “All Data”.

Resetting All Data Counter

“Contacts”

→

“Data Counter” → “Clear Counter”

Contacts 53

Call Costs

(M 8-7)

This function lets you check the charges for your calls.

Some networks do not support Charging Advice. Please check with your service provider for availability.

Checking the Cost of the Last Call

“Contacts”

The cost of the last call is displayed.

Checking the Total Call Cost

“Contacts” → “Call Costs” → “All Calls”

The cost of all calls is displayed.

Setting the Charge Rate

Set the charge rate to calculate the call cost and set the maximum limit for call cost.

“Contacts” → “Call Costs” → “Costs Units” → “Set Units”

1. Enter your PIN2 code.

2. Enter a cost per unit.

3. Enter a currency unit (up to 3 characters).

54 Contacts

→

“Call Costs” → “Last Call”

To enter a decimal point, press R.

Setting the Charge Limit

This function is useful if you wish to make sure you do not exceed a certain charge limit.

“Contacts” Limit”

→

“Call Costs” → “Max Cost” → “Set

1. Enter your PIN2 code.

2. Enter a value.

To enter a decimal point, press R.

Resetting All Call Costs

“Contacts”

→

“Call Costs” → “Clear Costs”

1. Enter your PIN2 code.

Checking the Residual Credit

“Contacts”

→

“Call Costs” → “Residual Credit”

Camera

(M 5)

(M 5-1)

Your phone has an integrated digital camera. This allows you to take and send pictures or video clips

wherever you are.

Take Picture

Put the phone into the digital camera mode to take a picture. Pictures are saved in Saved Pictures in JPEG format in the following six picture sizes.

1200 × 1600 dots/960 × 1280 dots/ 768 × 1024 dots/480 × 640 dots/ 240 × 320 dots/120 × 160 dots

Taking Pictures

“Camera” → “Take Picture”

The preview is displayed through the screen.

1. Press e or the side-down key to take the picture.

The shutter sounds and the still image of the taken picture is displayed. Press [Cancel] to retake a picture.

2. Press [Save].

“Saving (file name) to My Items…” is displayed, then the picture is registered.

3. Press F to return to standby.

Remaining shots indicator

123: Indicates the remaining number of

Tip

• If you wish to send a picture by multimedia message

after taking the picture, press e before step 2. Then select “Multimedia” or “Postcard”. (The Postcard service is not available with some service providers. Please contact your service provider for more information.) Large MMS messages may cause the size of attached pictures to be reduced.

• If you wish to set the focus for the picture subject,

press D, and the focus will be locked. You can then change the picture composition and take the picture.

pictures that can be taken.

Camera 55

Using the Full Screen

The preview can be displayed on the full screen without the soft key area and indicators.

“Camera” → “Take Picture” → [Options] → “Full Viewfinder”

1. Select “On” or “Off”.

[Options] is not displayed if “On” is selected. Press

when you need the option menu.

Note

• When “Picture Size” is set to “120*160”, you cannot use the full screen.

Tip

You can turn on/off full screen mode by pressing Q.

•

Using the Zoom Function

Press c or d to change the zooming ratio. Zooming ratio indicators

...: Magnification.

Note

• The number of magnifications will vary depending on the “Picture Size” setting.

56 Camera

Selecting the Picture Size

“Camera” “Picture Size”

→

“Take Picture” → [Options] →

1. Select the desired picture size.

Selecting the Picture Quality

→

“Camera” “Picture Quality”

“Take Picture” → [Options] →

1. Select “Normal”, “Fine” or “SuperFine”.

Picture quality indicators

: Super fine :Fine : Normal

Selecting the Anti-flicker Mode

“Camera” flicker”

→

“Take Picture” → [Options] → “Anti-

1. Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the picture due to the

light source. Change the anti-flicker mode to rectify.

• The digital camera uses a C-MOS sensor. Although

this camera has been manufactured to the highest specifications, some pictures may still appear too bright or too dark.

• If the phone has been left in a hot place for a long

time before taking or registering a picture, the picture quality may be poor.

Selecting the Storage Memory

Select the appropriate option.

“Camera” New Pictures”

→

“Take Picture” → [Options] → “Save

1. Select the desired location from “To Handset ”, “To

Memory Card” or “Choice”.

Note

• If you select “Choice”, select the desired location every time you save.

In the Case of No Available Memory

When the number of pictures that can be taken becomes 3 or less, the remaining shots indicator in the upper left of the screen turns red. (The number of pictures that can be taken is approximate.)

When the number of pictures that can be taken becomes 0, and when you try to take a picture again, “Memory full. Please delete some data!” is displayed.

Camera 57

Adjusting the Brightness of the Picture According to Lighting Conditions

Press a or b to adjust the brightness of the picture. Picture brightness (exposure level) indicators

: (Bright → Normal Once the phone has returned to the standby screen, the brightness settings return to default.

Viewing the Taken Pictures

“Camera” → “Take Picture” → [Options] → “My Pictures”

The list of pictures is displayed.

→

Dark)

1. Select the file you wish to view.

The selected picture is displayed.

Tip

• Your pictures are given file names which are

“pictureNNN” (NNN is a consecutive number). The file name (without an extension), date and size of your pictures are displayed in the list.

58 Camera

Using the Timer (Delay Timer)

“Camera” Timer”

→

“Take Picture” → [Options] → “Delay

1. Select “On” or “Off”.

When you select “On”, “ ” is displayed on the screen and the phone returns to digital camera mode. Note, however, that if “Continuous Shoot” on page 59 is activated, “ ” is displayed inst ead of “”.

Press e or the side-down key to start the delay timer. 10 seconds after the timer sounds, the shutter sounds, and the camera takes a picture.

Note

• The countdown sounds while the delay timer is operating.

•If e or the side-down key is pressed while the delay timer is operating, the picture is taken instantly.

• The zoom function with c or d, or brightness adjustment of the picture with a or b, is unavailable while the delay timer is operating.

• If you wish to stop taking pictures with the timer, press [Cancel] while the delay timer is operating.

Continuous Shoot

Four pictures are taken in succession. Auto Shoot and Manual Shoot are available.

Continuous Shoot indicators

: When pictures are taken in Continuous Shoot mode, these indicators appear on the screen.

* When delay timer and Continuous Shoot

functions are simultaneously set, “ ” is displayed instead.

“Camera” “Continuous Shoot”

→

“Take Picture” → [Options] →

1. Select “Auto Shoot” or “Manual Shoot”.

Select “Off” to cancel.

2. Press e or the side-down key to start Continuous

Shoot. Auto Shoot: Four pictures are taken in a row.

Manual Shoot: Pictures are taken one by one by

The taken pictures are saved automatically. To stop Continuous Shoot, press [Cancel].

pressing e or the side-down key.

Note

• When “Picture Size” is larger than “480*640”, you cannot use the Continuous Shoot function.

• When you select a frame for taking pictures, you cannot use the Continuous Shoot function.

• Delay timer cannot be used with the Manual Shoot function.

Selecting a Frame

You can select the frame from preset patterns. You can also select a frame in Saved Pictures.

“Camera” Frame”

→

“Take Picture” → [Options] → “Add

1. Select “Preset Frames”.

2. Select the desired frame.

The selected frame is confirmed on the display.

3. Press e.

Note

• When “Picture Size” is larger than “480*640”, you cannot use the Frame function.

• When you activate the Continuous Shoot, you cannot use the Frame function.

Camera 59

Selecting the Shutter Sound

(M 5-2)

You can select the shutter sound from 3 preset patterns.

“Camera” → “Take Picture” → [Options] → “Shutter Sound”

1. Select the desired shutter sound.

To play back the shutter sound, press [Play].

Note

• Continuous Shoot uses the specialised shutter sound that cannot be changed for the above settings.

Record Video

Put the phone into the video camera mode to record a video.

Video clips are saved in “.3gp” format in the following two modes:

Record size indicators

: Message sending mode enabled : Extended video mode enabled

60 Camera

Recording Video Clips

Sound can be recorded with the video clip.

“Camera”

The preview is displayed through the screen.

→

“Record Video”

1. Press e or the side-down key to start recording the

video clip. The sound for recording the video clip occurs.

If you press e or the side-down key again, or when the recording is completed, the sound for ending the video clip recording occurs and the display transits to step 2.

2. Select “Save”.

“Saving (file name) to My Items…” is displayed, then the video clip is registered. To preview a video clip before saving, select “Preview”. To send a video clip by multimedia message after recording the video clip, select “Save and Send”. To record a video clip again, press [Cancel].

Remaining sets indicator

123 : Indicates the remaining sets of video

clips that can be recorded.

Using the Zoom Function

Press c or d to change the zooming ratio. Zooming ratio indicators

...: Magnification.

Note

• The number of magnifications will vary depending on

the “Record Size” setting.

Selecting the Recording Size Mode

You can select the recording size mode.

“Camera” → “Record Video” → [Options] → “Record Size”

1. Select “Extended Video” or “For Message”.

Note

• If “For Message” is selected, the size of the video

clip that can be recorded depends on the message size set in MMS settings (p. 68).

• “Save and Send” is not displayed after recording in

extended video mode.

Selecting the Picture Size

“Camera” “Picture Size”

→

“Record Video” → [Options] →

1. Select the desired picture size.

Selecting Video Quality

“Camera” Quality”

→

“Record Video” → [Options] → “Video

1. Select “Normal”, “Fine” or “SuperFine”.

Video quality indicators

: Super fine :Fine : Normal

Selecting the Anti-flicker Mode

“Camera” flicker”

→

“Record Video” → [Options] → “Anti-

1. Select “Mode 1: 50Hz” or “Mode 2: 60Hz”.

Note

• Vertical stripes may occur on the preview screen due to the light source. Change the anti-flicker mode to rectify.

Camera 61

Selecting the Storage Memory

Select the appropriate option.

“Camera” → “Record Video” → [Options] → “Save New Videos”

1. Select the desired location from “To Handset ”, “To

Memory Card” or “Choice”.

Note

• If you select “Choice”, select the desired location every time you save.

In the Case of No Available Memory

When the number of video clips that can be recorded becomes 3 or less, the remaining sets indicator in the upper left of the screen turns red. (The number of sets that can be recorded is approximate.)

When the number of video clips that can be recorded becomes 0, and when you try to record a video clip again, “Memory full. Please delete some data!” is displayed.

Adjusting the Brightness of the Video Clips According to Light Conditions

Press a or b to adjust the brightness of the video clip.

Picture brightness (exposure level) indicators

: (Bright → Normal Once the phone has returned to the standby screen, the brightness settings return to default.

62 Camera

→

Dark)

Viewing Recorded Video Clips

“Camera” → “Record Video” → [Options] → “My Videos”

The list of video clips is displayed.

1. Select the file you wish to view.

2. Press e.

The selected video clip is played back. To pause playback, press e. To resume playback, press e again. To stop playback, press [Back].

Tip

• Your video clips are given file names such as “videoNNN” (NNN is a consecutive number). The file name (without an extension), date and size of your video clips are displayed in the list.

• If the video clip has been recorded with sound, the volume can be adjusted by pressing a (or d/the side-up key) or b (or c/the side-down key).

• The volume varies depending on the Multimedia Volume settings (p. 110). The sound is deactivated when “Multimedia Volume” is set to “Silent”.

Using the Timer (Delay Timer)

To Record a Video Clip with the Timer

“Camera” → “Record Video” → [Options] → “Delay Timer”

1. Select “On” or “Off”.

When you select “On”, “ ” is displayed on the screen and the phone returns to video camera mode.

2. Press e or the side-down key to start the delay

timer. 10 seconds after the timer sounds, the camera starts

recording the video clip.

Note

• The countdown sounds while the delay timer is operating.

•If e or the side-down key is pressed while the delay timer is operating, the video clip is recorded instantly.

• The zoom function with c or d, or brightness adjustment of the video with a or b, is unavailable while the delay timer is operating.

• If you wish to stop recording video clips with the timer, press [Cancel] while the delay timer is operating.

Recording Video Clips with Sound

“Camera” Record”

→

“Record Video” → [Options] → “Voice

1. Select “On” or “Off”.

Camera 63

Messages

(M 4)

(M 4-2)

(M 4-2-1)

Your phone allows you to send and receive text or multimedia as well as receive WAP alerts.

Multimedia (MMS)

About Multimedia Messaging

Multimedia Messaging Service (MMS) allows you to send and receive multimedia messages with graphical images, photographs, sound, animations or video clips attached.

Note

• Some MMS functions may not always be available

depending on your network. Contact your network operator for more information.

64 Messages

Creating a New MMS

→

“Multimedia” → “Create Message”

1. Enter the message.

To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Text Options”. Select “Add Text Template” and then select the desired template.

2. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Number” or “Enter Email Address” and enter the phone number or Email address.

3. Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• The current message size displayed while you are creating the message is an approximation.

• If a message cannot be sent for some reason, the message stays in the Outbox and “ ” is displayed on the standby screen.

Tip

• To save the message without sending, select “Save to Drafts” instead in step 3.

• To enter the subject, select “Subject” in step 3 and enter it. Up to 40 characters as the subject (and up to 20 recipients (for To and Cc)) can be entered. However, these may be limited depending on your network. In this case, you may not be able to send MMS. Contact your network operator for more information.

• To add more recipients, select “Add Contact” in step

3. Select “To” or “Cc” and select the desired number of the recipient. Then enter the phone number or Email address.

To Send a Message Template MMS

Your phone provides message templates with an image and voice attachment that help you create MMS easily.

→

“Multimedia” → “Create Message”

[Options] → “Message Template”

A confirmation screen asking whether you wish to discard the current text is displayed.

→

1. Confirm by selecting [Yes] or [No].

2. Select the desired template.

3. Enter the message.

4. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Number” or “Enter Email Address” and enter the phone number or Email address.

5. Select “Send”.

Note

• Selecting “Message Template” deletes messages or images you have entered or attached. To prevent deletion, select “Message Template” first, then enter messages.

Turning the Slide Show Setting On or Off

A → “Multimedia” → “Settings” → “Slide Show”

1. Select “On” or “Off”.

If You Select “On”

• You can create messages which have up to 10 slides. Each slide can contain one picture, one sound file and up to 1000 characters of text (up to the message total 100 KB or 300 KB limit).

Messages 65

• If you wish to add a slide to a single slide, press [Options] and select “Add Slide”. If you wish to perform slide operations for multiple slides, press [Options] and select “Slide Control”. The slide control options available are: Add: To add a new slide. Remove: To remove the active slide. Previous: To navigate to the previous slide. Next: To navigate to the next slide.

• Video clip data cannot be attached as slide data to the message.

If You Select “Off”

• You can attach a maximum of 20 pictures, sounds or video clips and up to 2000 characters of text (up to the message total 100 KB or 300 KB limit).

Inserting Attached Data

You can send pictures, sounds and video clips attached to multimedia messages. When attaching video clips, “Slide Show” must be set to “Off”.

→

“Multimedia” → “Create Message” →

[Options]

1. Select from “Picture”, “Sound” or “Video”.

2. Select from “Saved Pictures”, “Saved Sounds” or

“Saved Videos”.

66 Messages

3. Select the desired file.

The selected picture/sound/video clip is attached. When attaching is complete, press [Back] to return to the message creation screen.

• To add more files, press [Options] and select from “Add Picture”, “Add Sound” or “Add Video”. Then select from “Saved Pictures”, “Saved Sounds” or “Saved Videos”, and select the desired file.

• To remove the attached files, press [Options] and select “Remove”.

Note

• Pictures/Sounds/Video clips protected with a copyright cannot be sent attached to a message.

• Instead of performing step 2, you can send data recorded with “Take Picture”, “Record Voice” or “Record Video” options.

Reading MMS

Messages you receive are stored in the Inbox.

Incoming Messages

The MMS indicator ( ) will appear when you are receiving an incoming message.

→

“Multimedia” → “Inbox”

1. Select the message you wish to view.

The message is displayed.

2. Scroll the screen to read the message.

Tip

• The volume varies depending on the Multimedia Volume settings (p. 110). The sound is deactivated when “Multimedia Volume” is set to “Silent”.

Storing the Phone Number or Email Address of a Sender in the Contacts List

A → “Multimedia” → “Inbox”

1. Highlight the message from which you want to store

the phone number or Email address.

2. Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New Contact” on page 45.

Retrieving MMS

→

“Multimedia” → “Inbox”

When “ ” is in the Inbox, the following can be done.

1. Highlight the alert you wish to download.

2. Press [Options] and select “Download”.

Tip

• You can press e instead of step 2 to start

downloading.

Confirming Arrival of Delivery Report

A → “Multimedia” → “Sent”

1. Highlight the message of which you wish to confirm

arrival of delivery report.

2. Press [Options] and select “Delivery Report”.

This menu is available only for sent messages that have the “Delivery Report” set to “On”. For details on selecting “Delivery Report”, see “Setting Up MMS” on page 68.

Messages 67

Setting Up MMS

→

“Multimedia” → “Settings”

1. Select the item you wish to set up.

• Roam. Download (Immediate, Deferred): Controls MMS download timing when roaming outside of your network. Immediate: Downloads MMS immediately from

Deferred: Asks if you would like to download

• Delivery Rep. Allow (On, Off): Enables or disables Delivery Report when receiving a message which applies to the Delivery Report function.

• Anonymous Reject (On, Off): Rejects a messages from an unknown or empty address name or not.

• Auto Delete (Off, Inbox, Sent, Both): Deletes the oldest message automatically, when the Inbox, Sent or both (Inbox and Sent) is full.

68 Messages

the server.

from the server.

• Slide Show (On, Off): Enables or disables Slide Show when sending a message.

• Message Size (100 KB, 300 KB): Sets the maximum message size that can be sent.

• Advanced

• Priority:

Prioritises created messages.

• Delivery Report:

Enables Delivery Report.

• Expiry Time:

Sets Expiry Time for a message to be stored in the Server.

• Sender Visibility:

Displays the information about the sender.

• Slide Interval:

Sets the slide display time when sending a message.

2. Change each item.

Sending a Picture File with Postcard

Your phone allows you to send multimedia messages to a Vodafone specific Postcard service centre that prints the picture and mail it to the recipient’s home address specified in the MMS message. (Your phone is initially provided with the address of a Vodafone specific Postcard service centre, and its address cannot be changed.)

Note

• This service is not available with some service providers. Please contact your service provider for more information.

To Create a New Postcard

See the note on page 20 for menu references.

A → “Multimedia” → “Postcard”

1. Select “Saved Pictures”.

2. Select a picture you wish to use for a postcard.

3. Enter your message.

4. Select the desired recipient from the Contacts List

entries and enter the following information. If the desired entry does not exist, select “Enter

Address” and enter the following information.

See the note below for details.

•Name •City

• State/Province • Address

• Country • Post Code

5. Press [Options] and select “Send”.

Note

• Instead of performing step 1, you can use data taken with the “Take Picture” option.

• The items Name, Address and City are necessary to complete sending Postcards.

• Information for a recipient Name (mandatory):

Name of the recipient for a postcard up to 50 characters

Address (mandatory):

Address up to 50 characters

Post Code (optional):

Post code up to 20 characters

City (mandatory):

City up to 50 characters

Messages 69

State/Province (optional):

(M 4-3)

State, province, and region up to 50 characters

Country (optional):

Country up to 20 characters

•

The items displayed differ according to the service. Please contact your service provider for more information. When the item, “Country” is not displayed, you cannot send Postcards overseas.

• Files in Animation GIF format cannot be used for the Postcards service.

• The picture quality of Postcards varies depending on the picture size.

70 Messages

Text (SMS)

About Text Messaging

The Short Message Service (SMS) allows you to send text messages of up to 1024 characters to other GSM users.

To Use SMS with Your Phone

Messages longer than 160 characters may be composed. During sending, the messages are split. If the receiver has a suitable phone the message recombines when received, if not your message will be separated into several messages. You can send or receive SMS even if you are talking on the phone. You can also use Text Templates to help you compose SMS.

Creating and Sending a New SMS

(M 4-3-1)

→

“Text” → “Create Message”

1. Enter your message.

To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Add Text Template” and then select the desired template.

2. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Number” and enter the phone number.

3. Select “Send”.

The phone begins the sending process and the SMS is sent. After the message has been sent, the message is added to the Sent box. To save the message in the Drafts box without sending it, select “Save to Drafts”.

Note

• When you send a message of more than 160

characters, the confirmation message is displayed.

Tip

• To add more recipients, select “Add Contact” in step

3. Select an item number for adding the recipient’s phone number. Then enter the phone number.

Reading SMS

Incoming Messages

The SMS indicator ( ) will appear when an incoming message arrives.

1. When you receive a SMS, press e during standby.

2. Select the message you wish to view.

The sender’s phone number and a part of the message are displayed. When the sender’s phone number is stored in the Contacts List, the sender’s name is displayed instead of the phone number. Messages that are marked with “ ” denote unread messages. If the Inbox, Sent box or Drafts box is full, “ ” is displayed. Delete unnecessary messages.

3. Scroll the screen to read the message.

Extracting Phone Numbers from the Received Messages and Making a Call

You can make a call using the phone number embedded in the received SMS message.

A → “Text” → “Inbox”

1. Select the message from which you wish to extract

phone numbers.

Messages 71

2. Press [Options] and select “Extract Numbers”.

(M 4-3-5)

Telephone numbers embedded in the message are displayed.

3. Highlight the phone number.

4. Press [Options] and select “Make Call”.

To save this phone number in the Contacts List, select “Save Number”.

Setting Up SMS

To Set Up the Service Centre Address

→

“Text” → “Settings” → “Message Centre”

1. Enter the centre phone number.

If you wish to enter a country code for a message to an international number, press and hold Q until a “+” sign is displayed.

Message Lifetime

This indicates the number of days and hours for which a message you send may remain undelivered to the message recipient.

During this period, the message service centre will continually try to deliver the message to the recipient.

72 Messages

A → “Text” → “Settings” → “Message Lifetime”

1. Select the validity period.

Message Format

“Text” → “Settings” → “Message Format”

→

1. Select the message format.

Connection Type

→

“Text” → “Settings” → “Connection Type”

1. Select the connection type.

Optimisation

When set “On” (default), double-byte characters such as European characters with an accent are converted into single-byte characters and sent.

When “Off”, double-byte characters are sent as displayed.

Please note that you may be charged double for doublebyte characters sent in an SMS when Optimisation is set “Off”.

→

“Text” → “Settings” → “Optimisation”

1. Select “On” or “Off”.

Email

(M 4-4)

About Email Messaging

The Email service allows you to send and receive Email messages. Email messages of up to 2000 characters can be sent. The size of the Email messages to be received depends on Email settings.

Note

• You cannot send Email messages with files attached.

If you forward Email messages with files attached, the attached files are deleted.

Creating a New Email Message

A → “Email” → “Create Message”

1. Enter the message.

2. Select the desired recipient from the Contacts List

entries. If the desired entry does not exist, select “Enter

Email Address” and enter the Email address.

3. Select “Send”.

After the message is sent, the message is moved to the Sent box.

Note

• If a message cannot be sent for some reason, the message stays in the Outbox. To re-send the message, carry out the following:

→

“Email” → “Outbox”

1. Highlight the desired message.

2. Press [Options] and select “Re-send”.

Tip

• You can use the text template to make it easier to complete the message, and you can add your signature at the end of the message. To use the text template, move the cursor to the point you wish to insert the template. Press [Options] and select “Add Text Template”. Select the desired template. To add the signature, press [Options] and select “Add Signature”. Select the desired signature.

• Select “Save to Drafts” instead in step 3 to save the message without sending.

• Select “Subject” in step 3 to enter the subject. Up to 40 characters as the subject can be entered.

• Select “Add Contact” instead in step 3 to add more recipients (up to 30 recipients (for To, Cc and Bcc)). Select “To”, “Cc” or “Bcc” and select or enter the desired address of the recipients.

Messages 73

Reading an Email Message

(M 4-4-7)

Incoming Messages

The Email indicator ( ) will appear when there are unread messages.

A → “Email” → “Inbox”

1. Select the message you wish to view.

2. Scroll the screen to read the message.

Tip

•

If you wish to download Email messages, press A during standby and select “Email”. Then select “Check Email”.

Storing the Email Address of a Sender in the Contacts List

→

“Email” → “Inbox”

1. Highlight the message from which you want to store

the Email address.

2. Press [Options] and select “Save Sender”.

For details on entering a name, see “Add New Contact” on page 45.

74 Messages

Setting Up Email

→

“Email” → “Settings”

1. Select the item you wish to set up.

• Download Size (Whole Message, First 20KB): Controls the download size of the Email. The “Whole Message” option is limited to a maximum of 300 KB.

• Edit Signature: Opens the text template screen to edit the signature.

• Auto Delete (Off, Inbox, Sent, Both): Deletes the oldest message automatically when the Inbox, Sent or both (Inbox and Sent) is full.

• Reply Message (Incl. Original Mail, Excl. Original Mail): Includes or excludes the original message when replying.

Alert Inbox

Displays a list of WAP push messages. You can receive push messages via WAP Services. This means that a service provider sends WAP content to your phone, without any set up.

Cell Broadcasts

You can receive Cell Broadcast messages or general messages such as weather forecasts and traffic reports. This information is broadcasted to subscribers in certain network areas.

This function may not be available on all mobile phone networks. Contact your network operator for more information.

Enabling/Disabling Cell Broadcasts

A → “Cell Broadcasts” → “Switch On/Off”

1. Select “On” or “Off”.

Reading Cell Broadcast Messages

→

“Cell Broadcasts” → “Read Messages”

1. Select the desired subject.

2. Scroll the screen to read the message.

3. Press [Back].

Setting Languages

You can select your preferred language for the cell broadcast message display.

→

“Cell Broadcasts” → “Settings” →

“Language”

The current language is displayed.

1. Press e.

The language list is displayed.

2. Select the desired language.

3. Press [Save].

Subscribing to Cell Broadcasts

Select the page of the cell broadcast message that you want.

A → “Cell Broadcasts” → “Settings” → “Set Info Subjects”

1. Select “Add/Remove”.

If “Add/Remove” is not displayed on the screen, press [Options].

2. Select the desired page.

3. Press [Save].

Tip

• If the desired page is not in the list that appears in step 2, select “Create Subject” in step 1, then enter the subject code to add a page. For details on the subject code, contact your service provider.

Messages 75

Vodafone live!

(M 2)

Your phone is already configured to access Vodafone live! and the mobile Internet*.

Vodafone live! is a new mobile Internet portal which is your gateway to a new world of information, games, music and services.

Your phone uses GPRS, a system that is much faster than previous ways of getting information on a mobile phone. Also, the connection is ‘always on’ which means there is no need to wait for dialling up. You only have to pay for the data you send or receive, not how long you’re connected.

* If you have problems getting connected, please

phone Vodafone Customer Support.

Your phone contains a WAP browser used for surfing on the mobile Internet, where you can get a lot of useful information. Normally, pages are designed for a mobile phone.

76 Vodafone live!

Your phone is already setup to Vodafone site for WAP/ MMS Settings.

Starting the WAP Browser

1. Press C during standby.

To Exit the WAP Browser

1. Press F to exit the browser.

Navigating a WAP Page

• a b c d:

Move the highlights around in the screen.

• e: Executes the option displayed in the lower

centre of the screen.

• A: Launches browser option menu.

• C: Selects an action displayed in the lower

right corner of the screen. Used to access “Vodafone live!” by opening the browser.

• Q (press and hold):

Starts the “Go to URL”.

• G to O (press and hold):

Launches the Bookmark (WAP) after assigning “Hotkeys” with the “View bookmarks” option of the browser. For details on setting Hotkeys, see “Setting the Hotkeys to Web Page Bookmarks” on page 79.

• F: Exits the browser (short press).

Turns off the phone. (press and hold)

Browser Menu

When you are browsing, you can reach browsing options by pressing [Options].

•Select:

Selects the link you wish to see. (“Select” is displayed only when the link is highlighted.)

•Home:

Goes to the homepage you set in the WAP Settings.

• Add bookmark:

Adds the site you are currently browsing to your list of bookmarks.

• View bookmarks:

Displays a list of bookmarks.

• Save items:

Saves pictures, sounds or video clips in the appropriate My Items folder.

• Go to URL:

Inputs the URL of the site you wish to go to.

• History:

Displays a history list.

• Forward:

Moves to the next URL in the history list.

Vodafone live! 77

• Reload page: Refreshes the contents of the WAP page.

• Send URL: Sends current URL by SMS.

• Advanced...:

• Show URL:

Displays the URL of the site you are currently browsing.

• Save page:

Saves the page you are currently browsing to your list of Snap Shots.

• Snapshots:

Displays a list of Snap Shots.

• Alert Inbox:

Displays a list of WAP push messages. You can receive push messages via WAP Services. This means that a service provider sends WAP content to your phone, without any set up.

78 Vodafone live!

• Settings: Includes “Downloads”, etc.

• Security: Sets the security.

• Clear...: Clears history, cache, etc.

• Restart Browser: Restarts the browser.

• About ...: Displays the browser information.

Bookmarks

When you are browsing, press [Options] and select the appropriate option.

To Add a Bookmark

1. Select “Add bookmark”.

To Access Bookmarked Pages

1. Select “View bookmarks”.

2. Select the desired bookmark.

To Edit Bookmarks

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to edit.

4. Press [Options] and select “Details”.

5. Edit the title, then press b.

6. Edit the URL, then press b.

7. Select “Save”.

To Delete Bookmarks

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to delete.

4. Press [Options] and select “Delete”.

5. Press [Options] and select “OK”.

Setting the Hotkeys to Web Page Bookmarks

You can access Web pages quickly by pressing the shortcut keys (hotkeys). Follow the following to assign shortcuts:

1. Select “View bookmarks”.

2. Select “More…”.

3. Highlight a bookmark page you wish to edit.

4. Press [Options] and select “Hotkeys”.

The list of hotkeys is displayed.

5. Select the number to which you wish to assign

hotkeys. The list of registered bookmarks is displayed.

6. Select the desired bookmark.

Vodafone live! 79

My Items

(M 6)

(M 6-1)

My Items contains several types of picture, music, sound and video clip data. Also included in My Items are Text Templates and recently viewed WAP page addresses. You can also transmit picture, sound and video clip data via

Bluetooth

wireless technology to OBEX-enabled phones.

Note

• The phone can store approximately 30 MB of data across Pictures, Games & More, Sounds and Videos.

Pictures

Pictures that are taken by your phone’s camera or images that are downloaded from mobile Internet sites can be managed.

Viewing Pictures

“My Items” → “Pictures” → “Saved Pictures”

1. Press d to display the list from the memory card

and c to return to the handset memory.

2. Select the file you wish to view.

The selected picture is displayed.

80 My Items

Using Images as Wallpaper

“My Items” → “Pictures” → “Saved Pictures”

The list of pictures is displayed.

1. Highlight the file you wish to use as wallpaper.

2. Press [Options] and select “Set as Wallpaper”.

3. Specify the area you wish to display using the

navigation keys.

Editing Pictures

“My Items”

→

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to edit.

2. Press [Options] and select “Edit”.

3. Select the desired option:

“Rotate”: The picture is rotated 90º

“Adjust Size”: Select the desired option. “Rename”: Rename the file name. “Retouch”: Select the retouching option. “Add Frame”: Select the desired frame pattern. “Add Stamps”: Press [Stamps] and select the

anticlockwise. Press [Rotate] again for another 90º.

desired stamp pattern. Repeat this step to add more patterns.

Note

• The size of pictures that you can retouch is 52 dots

[W] × 52 dots [H] minimum.

• The size of pictures that you can add stamps to is 48

dots [W] × 48 dots [H] minimum.

• Images exceeding 240 [W] or 320 [H] are saved as

240 [W] × 320 [H] regardless of the original size.

• “Adjust Size” may not be available depending on the

original picture and copyright issued.

Sending a Picture File

“My Items” → “Pictures” → “Saved Pictures”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia”, “As Postcard” or “Via

Bluetooth”. For details on creating a message, see “Creating a

New MMS” on page 64.

Note

• The Postcard service is not available with some

service providers. Please contact your service provider for more information.

• Pictures protected with a copyright cannot be sent

attached to a message.

• Pictures stored in a memory card cannot be sent via

Bluetooth.

Tip

• For details on transmitting My Items data, see “Sending My Items Data” on page 87.

Saving to Contacts List

You can use this option only for pictures saved in the handset memory.

“My Items”

→

“Pictures” → “Saved Pictures”

1. Highlight the file you wish to add to Contacts List.

2. Press [Options] and select “Add to Contact”.

To overwrite, select “Existing Contact” and select the data you wish to save to. If the picture size exceeds 176 dots in width or 220 dots in height, specify the area you wish to display. To save as a new entry, select “New Contact”.

• For details on entering a name, see “Add New Contact” on page 45.

My Items 81

Uploading Picture Files

(M 6-1-3)

(M 6-2)

You can upload your pictures to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

“My Items” → “Pictures” → “Saved Pictures”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

4. Press [Yes].

Note

• Pictures protected with a copyright cannot be uploaded.

Downloading Picture Files

“My Items” → “Pictures” → “More Pictures”

The picture file download site is displayed.

82 My Items

Games & More

Along with the preloaded applications, downloaded applications are stored in Applications.

Note

• Applications can store up to 50 applications.

Using Applications

Various kinds of Vodafone specific applications can be used in this phone.

To use applications, download the applications via the mobile Internet.

Some applications offer the ability to connect to a network either within a game or network based application.

Note

• Applications may be both local (no connectivity) and network based (using the mobile Internet to update information/play games). The network may charge you more for using network-based applications. Please contact your service provider for more information.

Downloading Applications

(M 6-2-1)

(M 6-2-2)

(M 6-3)

Confirmation Screen

Before downloading the application you are asked to confirm what you are about to receive.

After checking the information on the confirmation screen, the application can be downloaded.

Note

• User authentication may be required before downloading the application on some information screens.

Executing Applications

“My Items”

Downloaded applications are sequentially displayed from the latest one.

→

“Games & More” → “Applications”

1. Select the title of the application you wish to

execute. The selected application is executed.

When using network connection type applications, connection to the network can be selected.

2. To end the application, press F and select “End”.

More Games

“My Items”

→

“Games & More” → “More Games”

1. Select the application you wish to download.

The WAP browser is started and a confirmation message will appear asking to confirm download.

2. Press e to start downloading.

3. Press e when finished.

Sounds

The ringtones, the sound files and the AMR data recorded by Voice Recorder are managed in Saved Sounds.

Sound files in the following formats can be played back.

SMAF/Standard MIDI/i Melody/WAVE/AMR/MP3/ AAC

Note

• The extensions which are supported by AAC are mp4/ 3gp/m4a.

Tip

• SMAF (Synthetic music Mobile Application Format) is a format of music data for mobile phones.

My Items 83

Playing Back Sound Files

“My Items”

→

“Sounds” → “Saved Sounds”

1. Press d to display the list from the memory card

and c to return to the handset memory.

2. Select the file you wish to play back.

To stop playback, press e.

Note

• The volume varies depending on the Multimedia Volume settings (p. 110). The sound is deactivated when “Multimedia Volume” is set to “Silent”. To adjust the volume, press a (or d/the side-up key) or b (or c/the side-down key).

84 My Items

Using the Sound Files as Ringtone

“My Items”

→

“Sounds” → “Saved Sounds”

1. Highlight the file you wish to use as ringtone.

2. Press [Options] and select “Set as Ringtone”.

The selected sound is automatically used for the ringtone of the current Profiles.

Note

• Files in the memory card cannot be used for the ringtone.

• Files in AMR or WAVE format cannot be used for the ringtone.

Sending a Sound File with MMS

“My Items”

→

“Sounds” → “Saved Sounds”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia”.

For details on creating a message, see “Creating a New MMS” on page 64.

Note

• Sounds protected with a copyright cannot be sent attached to a message.

Uploading Sound Files

(M 6-3-3)

(M 6-4)

You can upload your sounds to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

“My Items” → “Sounds” → “Saved Sounds”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

4. Press [Yes].

Note

•

Sounds protected with a copyright cannot be u ploaded.

Downloading Sound Files

“My Items”

The sound file download site is displayed.

→

“Sounds” → “More Sounds”

Videos

Video clips that are recorded by your phone’s video camera or video clips that are downloaded from mobile Internet sites can be managed.

Playing Back Video Clip Files

“My Items” → “Videos” → “Saved Videos”

1. Press d to display the list from the memory card

and c to return to the handset memory.

2. Select the file you wish to play back.

3. Press e.

To pause, press e again. To stop playback, press [Back]. To return to the original size, press [×1].

Note

My Items 85

Sending a Video Clip File with MMS

(M 6-4-3)

“My Items”

→

“Videos” → “Saved Videos”

1. Highlight the file you wish to send.

2. Press [Options] and select “Send”.

3. Select “As Multimedia”.

For details on creating a message, see “Creating a New MMS” on page 64.

Note

• Video clips protected with a copyright cannot be sent attached to a message.

86 My Items

Uploading Video Clip Files

You can upload your video clips to the Media Album.

Note

• This service is not available with some service providers. Please contact your service provider for more information.

“My Items”

→

“Videos” → “Saved Videos”

1. Highlight the file you wish to upload.

2. Press [Options] and select “Send”.

3. Select “To Album”.

4. Press [Yes].

Note

• Video clips protected with a copyright cannot be uploaded.

Downloading Video Clip Files

“My Items” → “Videos” → “More Videos”

The video clip file download site is displayed.

Sending My Items Data

Choose the appropriate menu. See page 102 (Connectivity) for further information on Bluetooth wireless technology.

“My Items” → “Pictures” → “Saved Pictures” “My Items” → “Sounds” → “Saved Sounds” “My Items” → “Videos” → “Saved Videos”

1. Highlight the desired file.

2. Press [Options] and select “Send”.

3. Select “Via Bluetooth”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the file is sent.

Note

• Data which has been saved onto memory cards cannot be sent.

• Pictures/Sounds/Video clips protected with a copyright cannot be sent.

Receiving the My Items Data

When the phone receives the My Items data, a confirmation message appears.

1. Press [Yes].

The received data is registered in the corresponding My Items folder. The data can only be stored in handset memory. Press [No] to reject.

Tip

• For details on Bluetooth wireless settings, see “Connectivity” on page 102.

Copying or Moving My Items Data

You can copy or move My Items data between the handset memory and the memory card.

“My Items” “My Items” → “Sounds” → “Saved Sounds” “My Items” → “Videos” → “Saved Videos”

→

“Pictures” → “Saved Pictures”

1. Highlight the desired file.

2. Press [Options] and select “Move to Card”, “Copy

to Card”, “Move to Handset” or “Copy to Handset”.

Note:

• Some large files may not be able to be copied/moved.

My Items 87

Text Templates

(M 6-5)

(M 6-7)

You can register up to 20 text templates for use in text messages and multimedia messages.

120 characters may be registered in any text template.

Adding Phrases to Text Templates

“My Items”

1. Select the number you wish to register.

2. Enter the text and press e.

Editing Text Templates

“My Items” → “Text Templates”

1. Highlight the text template you wish to edit.

2. Press [Options] and select “Edit”.

3. Enter new text and press e.

Viewing Text Templates

“My Items”

The list of Text Templates is displayed.

1. Highlight the text template you wish to view.

2. Press [Options] and select “View”.

88 My Items

→

“Text Templates”

→

“Text Templates”

Deleting Text Templates

“My Items”

→

“Text Templates”

1. Highlight the text template you wish to delete.

2. Press [Options] and select “Delete”.

Memory Status

This function helps you to check the memory status of the handset memory or memory card. Memory status covers the following.

Handset Memory: Applications, Pictures, Sounds,

Memory Card: Pictures, Sounds, Videos, Others,

“My Items”

1. Select “Handset Memory” or “Memory Card”.

Videos, Total and Free

Total and Free

→

“Memory Status”

Games & More

(M 1)

(M 1-1)

Applications

The list of Java™ applications is displayed. Downloaded applications are displayed in order

starting from the latest one.

Executing Applications

For details on executing applications, see “Executing Applications” on page 83.

Showing Application Details

“Games & More”

1. Highlight the desired Java™ application.

2. Press [Options] and select “Application Details”.

The detailed information is displayed.

Setting Permission

When using Java™ applications that access the network, online security for monetary transactions can be set with this option.

To Select the Function and Confirmation Method

“Games & More”

1. Highlight the desired Java™ application.

2. Press [Options] and select “Permission”.

→

“Applications”

→

“Applications”

3. Select “Network Access” to set how the Java™

application accesses the network.

4. Select the desired confirmation method.

Always Connect: Allows the Java™ application access

First Time: Informs you when the Java™

Per Session: Informs you when the Java™

Per Access: Informs you every time the Java™

Never Connect: Prevents the Java™ application from

without confirmation.

application accesses the network for the first time. If access is allowed, no more confirmations are made until you delete the application.

application accesses the network for the first time. If access is allowed, no more confirmations are made until the application finishes operation.

application accesses the network regardless of whether or not access is allowed.

accessing the network and no confirmation is made.

Games & More 89

To Reset Permissions

(M 1-2)

(M 1-2-2)

(M 1-2-3)

(M 1-3)

You can reset all permissions you made.

“Games & More” → “Applications”

1. Highlight the desired Java™ application.

2. Press [Options] and select “Permission”.

3. Select “Reset Permissions”.

Screensavers

You can download screensaver applications for the standby screen.

“Games & More” → “Screensavers” → “Switch On/Off”

1. Select “On” or “Off”.

Note

• If you select “On” and a screensaver application is not set, a list displaying available screensavers appears, asking you to make a selection.

Set Application

“Games & More” Application”

The downloaded applications are displayed.

1. Select the desired screensaver application.

90 Games & More

→

“Screensavers” → “Set

Resume Time

You can set the time period for the screensaver application to activate.

“Games & More” → “Screensavers” → “Resume Time”

1. Enter the resume time in two digits using the digit

key.

More Games

You can download applications.

“Games & More”

The application download site is displayed.

1. Select the application you wish to download.

The WAP browser is started and a confirmation message will appear asking to confirm download.

2. Press e to start downloading.

3. Press e when finished.

→

“More Games”

Settings

(M 1-4)

(M 1-4-1)

(M 1-4-2)

(M 1-4-3)

Calls & Alarms

You can set the priority of incoming calls and alarms while an application is operating.

“Games & More”

1. Select “Incoming Call” or “Alarm”.

2. Select methods.

• “Call Priority” or “Alarm Priority”:

The application is suspended automatically, and you can receive a call, or the alarm will sound. After finishing the call or the alarm ends, the suspend icon ( ) is displayed letting know there is a suspended application.

• “Call Notice” or “Alarm Notice”:

The marquee (character scrolls) is displayed on the first line of the screen while the application continues. If you press D, the application is suspended, and you can receive a call. After finishing the call, the suspend icon ( ) is displayed letting you know there is a suspended application.

→

“Settings” → “Calls & Alarms”

Sound Volume

You can set the volume of the application such as sound effect to one of the five levels or silent. When “Multimedia Volume” (p. 110) is set to “Silent”, this setup has priority.

“Games & More”

The current volume level is displayed.

→

“Settings” → “Sound Volume”

1. Press a (or d) to increase the volume or press b

(or c) to decrease the volume and then press e.

Backlight

“Games & More” “Switch On/Off”

→

“Settings” → “Backlight” →

1. Select from “Always On”, “Always Off” or

“Default Settings”.

• “Always On”: Lit while the application

• “Always Off”: Unlit while the application is

• “Default Settings”: Works with the main backlight

is operated.

operated even if a key is pressed.

setting. (p. 114)

Games & More 91

To Set the Blinking Operation

(M 1-4-4)

(M 1-4-5)

(M 1-5)

This setting enables the backlight to be controlled by the application. If set to “Off”, the backlight cannot be turned on from the application.

“Games & More” → “Settings” → “Backlight” → “Blink”

1. Select “On” or “Off”.

Vibration

When the vibrator is set in the application, you can choose whether the operation is enabled or disabled.

When a SMAF file is specified in the application, you can operate the vibrator set in the SMAF file.

Note

• SMAF (Synthetic music Mobile Application Format) is a music data format for mobile phones.

“Games & More”

→

“Settings” → “Vibration”

1. Select from “On” or “Off”.

92 Games & More

Set to Default

To Reset All Items in Settings Menu

“Games & More”

→

“Settings” → “Set to Default”

1. Enter your handset code.

The default handset code is “0000”. For details on changing the handset code, see “To Change Handset Code” on page 126.

Java™ Information

The information about the licences belonging to Java™ is displayed.

Applications

(M 3)

(M 3-1)

(M 3-2)

SIM Application

You can refer to the information on the SIM. Contact your service provider for further details.

Calendar

The calendar allows you to easily schedule appointments.

These entries can also be sent via Bluetooth wireless technology to a PC to share the same schedules.

Creating a New Entry

“Applications”

1. Highlight the desired day to which you want to add

an event.

2. Press [Options] and select “Add New Entry”.

3. Enter the subject.

4. Enter the location.

5. Select the desired category.

6. Enter the start date.

7. Enter the start time.

8. Select the desired duration.

9. Select the desired reminder option.

→

“Calendar”

Note

• The reminder function sounds even if the phone is switched off.

• The reminder will not sound when “Ringer Volume” (p. 106) is set to “Silent”.

• When selecting “Other” in step 8, you can enter the desired end date and time.

• When selecting “Other” in step 9, you can enter the desired date and time.

• On the date entry screen when entering “Start Date” in step 6 or choosing “Other” in steps 8 and 9 and so on, press [Options] and select “Refer to Calendar” to make it easier to find the desired date from the monthly calendar that is displayed.

Applications 93

Editing the Reminder Tone

“Applications” → “Calendar”

1. Select the day including schedule entries the

reminder tone of which you wish to edit.

2. Highlight the desired entry.

3. Press [Options] and select “Edit”.

4. Select the reminder field and select the desired

option. If you select “No Reminder”, the reminder is turned

off.

5. Select “Tone” and select “Preset Sounds” or “My

Sounds”.

6. Select the desired tone.

For details on selecting a tone, see “Assigning Ringtone” on page 107.

7. Select “Vibration” and select from “On” or “Off”.

For details on selecting a vibration, see “Vibration” on page 107.

8. Select “Duration” and enter the desired time.

9. Press [OK].

10.Press [Save].

94 Applications

Sending a Schedule Entry

“Applications”

→

“Calendar”

1. Select the day including schedule entries you wish

to send.

2. Highlight the desired entry you wish to send.

3. Press [Options] and select “Send”.

4. Select “Via Bluetooth”.

For “Via Bluetooth”

The phone starts searching for Bluetooth wireless technology enabled devices within 10 metres.

When detected, a list of enabled devices is displayed allowing you to select the desired device. The connection can be established and the entry is sent.

Note

Receiving a Schedule Entry

When the phone receives a schedule entry, a confirmation message appears.

1. Press [Yes].

The received entry is registered in the Calendar. Press [No] to reject.

Tip

• For details on making Bluetooth wireless settings, see “Connectivity” on page 102.

Viewing an Entry

“Applications”

→

“Calendar”

1. Select the day including schedule entries you wish

to view. The list of entries is displayed.

2. Select the desired entry.

Press d to switch entries, if available, in the selected day.

To Search By Date

1. In the monthly or daily view, press [Options].

2. Select “Go to”.

3. Select “Today” to display today or “Enter date” to

enter the desired date.

To Search By Subject

1. In the monthly or daily view, press [Options].

2. Select “Find”.

3. Enter the desired text.

To Change the Week Format

1. In the monthly view, press [Options].

2. Select “Week Format”.

3. Select “Monday-Sunday” or “Sunday-Saturday”.

Deleting Entries

1. In the monthly or daily view, press [Options].

2. Select “Delete”.

3. Select the desired option.

• “This Entry” (daily view only):

• “All this Day”: Deletes all entries for the selected

• “All this Month”: Deletes all entries for the selected

• “Up to Last Month”:

• “All Entries”: Deletes all entries in this

Deletes the selected entry.

day.

month.

Deletes all entries before this month.

application.

Applications 95

Alarms

(M 3-3)

Setting the Alarms

The alarm function allows you to be alerted at a specified time. Note that the alarm may not function correctly if the clock has not been set.

Note

• The alarm functions even if the phone is switched off.

• The alarm will not ring when “Ringer Volume” (p. 106) is set to “Silent”.

“Applications”

1. Select the blank setting.

2. Enter the desired time.

To Change the Type of Alarm Tone

3. Select “Set Alarm Tone”.

4. Select “Tone”.

5. Select “Preset Sounds” or “My Sounds”.

96 Applications

→

“Alarms”

6. Select the desired tone.

For details on selecting a tone, see “Assigning Ringtone” on page 107.

To Change the Vibration of Alarm Tone

7. Select “Vibration”.

8. Select “On” or “Off”.

For details on selecting a vibration, see “Vibration” on page 107.

To Change the Duration of Alarm Tone

9. Select “Duration”.

10.Enter the desired time (02-59).

11.Press [OK].

To Set the Repeating Option

12.Select “Repeat Daily”.

13.Select “On” or “Off”.

14.Press [Save].

Editing the Alarm Setting

(M 3-4)

“Applications”

→

“Alarms”

1. Select the desired setting and edit it.

Resetting an Alarm Setting

“Applications”

→

“Alarms”

1. Select the alarm you wish to reset.

2. Press [Options] and select “Reset Alarm”.

Resetting All Alarm Settings

“Applications”

Deactivating or Activating an Alarm

“Applications”

→

“Alarms” → “Clear All”

→

“Alarms”

1. Highlight the alarm you wish to deactivate or

activate.

2. Press [Options] and select “Switch Off” or “Switch

On”.

Calculator

The calculator function performs the 4 arithmetic calculations using up to 11 digits.

“Applications” → “Calculator”

The calculator is displayed on the display. Key operations for calculation are as follows:

To enter a decimal point, press R. To clear the entered number or operand, press [Clear]. To do the calculations, press e. To start a new calculation, press [Clear].

Applications 97

Rate Conversion

(M 3-5)

You can also use the calculator as a currency calculator to convert from/to a home currency using a conversion rate that you enter.

To Set a Currency Conversion Rate

“Applications” “Exchange Rate”

→

“Calculator” → [Options] →

1. Select “Foreign -> Domestic” or “Domestic ->

Foreign”.

2. Enter the currency conversion rate.

To delete all digits, press [Clear].

To Convert a Value

“Applications”

→

“Calculator”

1. Enter the value to be converted.

2. Press [Options] and select “In Domestic” or “In

Foreign”. The result is displayed.

Note

• You cannot perform step 2 when an arithmetic

+, −, ×

symbol (

98 Applications

or ÷) is displayed.

Voice Recorder

This allows you to record a voice clip of up to 180 seconds, which can be used to remind you of schedule entries or be sent within a multimedia message. The recorded voice clip is registered in Saved Sounds. Voice clips are saved in “.amr” format.

Recording a Voice Clip

“Applications” → “Voice Recorder”

1. Press e to start recording.

To stop recording before the recording time is over, press e.

2. Select “Save” to save the voice clip.

To play back the recorded voice clip, select “Playback”. To record a voice clip again, press [Cancel].

Note

• To change recorded size before recording, press [Options] and select “Record Size”. Then select “Extended Voice” or “For Message”.

• The volume varies depending on the Multimedia

(M 3-6)

Volume settings (p. 110). The sound is deactivated when “Multimedia Volume” is set to “Silent”. To adjust the volume, press a (or d/the side-up key) or b (or c/the side-down key).

Sending Voice Clips

“Applications” → “Voice Recorder”

1. Press e to start recording.

2. Press e to stop recording.

3. Select “Save and Send”.

For details on creating a message, see “Creating a New MMS” on page 64.

Note

• “Save and Send” is not displayed after recording in extended voice mode.

Phone Help

You can view the help list and use it to guide you in the phone’s functions.

“Applications” → “Phone Help”

1. Press a or b.

Applications 99

Sharp GX34 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

Introduction

Useful Functions and Services

SAFETY PRECAUTIONS

RADIOFREQUENCY (RF) EXPOSURE

DISTRACTIONS

PRODUCT HANDLING

ELECTRICAL SAFETY

INTERFERENCE

EXPLOSIVE ENVIRONMENTS

CONDITIONS OF USE

Table of Contents

List of Menu Functions

Your Phone

Optional Accessories

Getting Started

Charging the Battery

Inserting/Removing the Memory Card

Connecting the Handsfree Kit

Turning Your Phone On and Off

Display Indicators (Main Display)

Display Indicators (External Display)

Navigating Functions

Call Functions

Making a Call

Speed Dialling

Redialling

Answering a Call

Incall Menu

Entering Characters

Changing the Input Languages

Changing the Input Method

Using Text Templates

Using the Menu

Contacts

Contacts List

Selecting the Storage Memory

Changing the List Displayed

Changing the Name Order

Add New Contact

Copying Contacts List Entries between SIM Card and Handset

Finding a Name and Number

Dialling from the Contacts List

Editing Contacts List Entries

Deleting Contacts List Entries

Viewing Groups

Group Call

Assigning a Ringtone to Each Contacts List Entry

Memory Status

Speed Dial List

Sending a Contacts List Entry

Receiving a Contacts List Entry

Dialling a Service Phone Number

Call Log

Speed Dial List

My Numbers

Call Timers

Data Counter

Call Costs

Camera

Take Picture

Record Video

Messages

Multimedia (MMS)

Text (SMS)

Email

Alert Inbox

Cell Broadcasts

Vodafone live!

Starting the WAP Browser

Navigating a WAP Page

My Items

Pictures

Games & More

Sounds

Videos

Text Templates