Sharp GL6ZV27 Datasheet
PREPARED BY: DATE:
Sdt3 I( &M
7 (/Ledc
APPROVED BY: DATE:
Jti‘, / /Myy
J L&S&
33’
DEVICE SPECIFICATION FOR
MODEL No.
ELECTRO~c CObiPONENTS GROUP
SHARP CORPORATION
SPECIJWATION
Light Emitting Diode
SPECNo. Ix996046
I
ISSUE
I
hut/l 6/99
\
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
* OA equipment * Audio visual equipment * Home appliance
* Telecommunication equipment (Terminal)
* Tooling machines
L
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3), please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures. such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers * Rescue and security equipment
* Other safety equipment
[
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
* Space equipment
* Nuclear power control equipment * Medical equipment
c
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
* Computers
* Telecommunication equipment (for trunk lines)
GL6ZV27
* Measuring equipment
1
1
CUSTOMER’S APPROVAL
‘DATE:
BY:
DATE:
PRESENTED BY:
M.Katoh,
Department General Manager of
Engineering DeptJII
Optc-Electronic Devices Division
Electronic Components Group
SHARP CORPORATION
Jm /fC
,
3fQ@@
/Y
ry
MODEL No.
GL6ZV27 Snecifrcation
1. Application
This specification applies to the light emitting diode device Model No. GL6ZV27.
[AlGaInP (dicing or scribe/brake type> Amber LED device]
DG996046
Jun/16/99
PAGE
GL6ZV27 l/10
2. Outline dimensions and pin
3. Ratings and characteristics
COMeCtiOIIS
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refer to the attached sheet Page 2.
Refer to the attached sheet Page 3-4.
3- 1. Absolute maximum ratings
3-2. Eleciro-optical characteristics
3-3. Derating Curve
3-4. Characteristics Diagram
4. Reliability
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refer to the attached sheet Page 5.
4-1. Test items and test conditions
4-2. Measurement items and Failure judgement criteria
5. Incoming inspection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*.............o
Refer to the attached sheet Page 6.
5- 1. Applied standard
5-2. Sampling method and level
5-3. Test items, judgement criteria and classifica of defect
5-4. Test items the surface is be applied for fiat type, judgement criteria and classifrca of defect
6. Supplement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..~
6-l. Packing
6-2. Luminous intensity rank
6-3. Dominant wavelength rank
64. Environment
7. Precautions for use
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7- 1. Lead forming method
7-2. Notice of installation
7-3. Soldering Conditions
.7-4. For cleaning
Refer to the attached sheet Page 7-8.
Refer to the attached sheet Page 9- 10.
MODELNo.
I
DG996046
GL6ZV27
JllnA6/%
PAGE
I z/l0
2. Outline dimensions and pin
COMeCtionS
5. 8 20. 2
9,
I/
I
I
Colorless transparency
2.54 OM
l-t-
I
%b-
I
pin COMIXtiOIlS
0
ote) Unspecified tol. to be ~0.2m-n
ate) Cold rolled steel leads are plated with but the tie-bar cut portions have no plating do not solder this part of the product.
unit
mm
Lead : (Fe) Cold rolled steel
Package : Epoxy resin
Material
Finish
Lead : Sn plated or wave soidering
0. Anode
0. cathode
Drawing No.
51106027
3.
Ratings and characteristics
(Note 1) Duty ratio=l/lO,Pulse width=O.lms
(Note 2) At the position of 1.6m.m from the bottom resin package
MODEL No.
DG996046
GL6ZV27
Jun/16/99
PAGE
3110
3-2.
Electra-optical
Parameter Sylllbol
Forward voltage
LLlminous interlsity (Note 3)
Peak emission wavelength
characteristics
vF
Iv
J-P
Conditions
IF=2OmA
Dominant wavelength Ad
Spectrum radiation bandwidth A ;1
Reverse current I,
Terminal capacitance
Viewing
Xaxis
28 l/2 IF=2OmA
Ct V=OV.f=lMHz
VR=4V
Angle YilXiS
(Note 3) Refer to the suplement item 6. regarding the standard of rank cla
3-3. Derating Curve
Peak Forward Current Derating Curve
120
a
.5
100
z
g 80
,”
2 60
-0
ii 40
i
,” 20
:
”
-25 0 25 50 7585 100 125
Forward Current Derating Curve
60
50
40
30
20
10
0
-25 0 25 50 75 85 100 125
(Ta=25”C
MIN. TYP. MAX. unit
-
2.1 2.6 V
w
;ification.
Ambient Temperature Ta(“C)
Ambient Temperature TarC)
Loading...