PREPARED BY: DATE: I 1 SPEC.No. Ix996047
ELECTRONIC COMPONENTS GROUP
SHARP
CORPORATION
I
Opto-Ekctronic Devices Division
SPiXIFICATION
DEVICE SPECIFICATION FOR
Light Emitting Diode
MODEL No.
GL6ZS27
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
* OA equipment * Audio visual equipment * Home appliance
* Telecommunication equipment (Terminal) * Measuring equipment
* Tooling machines
r
If the use of the prcxluct in the above application areas is for equipment listed in paragraphs
(2) or (3), please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals * Gas leakage sensor breakers * Rescue and security equipment
* Other safety equipment
[
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
* Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment * lMedica1 equipment
C
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
3. Please contact and consult with a Sharp sales representative for any questions about this product.
* Computers
1
I
1
1
CUSTOMER’S APPROVAL
DATE:
BY:
DATE:
PRESENTED BY:
,
M.Katoh,
Department General Manager of
Engineering Dept.,J.II
Opto-Electronic Devices Division
Electronic Components Group
SHARP CORPORATION
/
MODELa No.
I
GL6ZS27 Swcifkation
1. Application
This specification applies to the light emitting diode &vice Model No. GL6ZS27.
[AlGalnP (dicing or scribe/brake type) Sunset-orange LED
device1
DG996047
GL6ZS27 l/10
Jurd16/!w
PAGE
2. Outline dimensions and pin
3. Ratings and characteristics
3- 1. Absolute maximum ratings
3-2. Electra-optical characteristics
3-3. Derating Curve
3-4. Characteristics Diagram
4. Reliability
4- 1. Test items and test conditions
4-2. Measurement items and Failure judgement criteria
5. Incoming inspection
5- 1. Applied standard
5-2. Sampling method and level
5-3. Test items, judgement criteria and classifica of defect
54. Test items the surface is be applied for flat type, judgement criteria and classifica of defect
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
co~ections
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*.......
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..a
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refer to the attached sheet Page 2.
Refer to the attached sheet Page 3-4.
Refer to the attached sheet Page 5.
Refer to the attached sheet Page 6.
6. Supplement
6-1. Packing
6-2. Luminous intensity rank
6-3. Dominant wavelength rank
6-4. Environment
7 . ~ecau~onsforuse . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7-l. Lead forming method
7-2. Notice of installation
7-3. Soldering Conditions
7-4. For cleaning
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refer to the attached sheet Page 7-8.
Refer to the attached sheet Page g-10.
3. Ratings and characteristics
I
3- 1. Absolute maximum ratings
Parameter
Power dissipation
Symbol -.
P
Value
130
Storage temperature 1 Tstg 1 -40 - 100 1 “C
soldering temperature(Note 2) 1 Tsol 1 26O(within5 seconds) I “C
(Note 1) Duty ratio=l/lO,Pulse width=O.lms
(Note 2) At the position of 1.6mm from the bottom resin package
MODEL No.
I
(Ta=25”C)
Unit
mW
Dci996047
GL6ZS27
I Jun/16/99
PAGE
I 3110
I
(Note 3) Refer
to
the suplement item 6. regarding the standard of rank classification.
3-3. Derating Curve
Peak Forward Current Derating Curve
120
3
100
E
2 80
E
2 60
Ambient Temperature Ta(‘C)
Forward Current Derating Curve
60
3 5o
L
; 40
s
= 30
5
$ 20
r
li 10
0
-25 0 25 50 75 ‘%OO 125
Ambient Temperature Ta (“C)
MODEL No.
I
DG996047
GL6ZS27
Jun/16/99
PAGE
I 4110
Peak Forward Current vs. Duty Ratio
10
l/loo l/l0
Duty Raito DR
1
3-4. Characteristics Diagrarn(typ) (Note 1)
Forward Current vs.Forward Voltage
100
(Ta=25%1
10
(Ta=25"C)
Relative Luminous intensity
vs. Ambient Temperature
(IF=2OnA)
10
I i I I i
1
(),I I I I I I I/i 1 I I I I II 11
1 1.2 1.4 1.6 1.8 2 2.2 2.4 2.6
Forward Voltage VFW
Relative Luminous lntmrity vs. Froward Voltage
1000
100
0. 1
i / i i I
I I
Y
-60-40-20 0 20 40 60 80 100 120
Ambient Temprature Ta('C)
(Ta=25"C)
(Note 1)
0.01
0.
1 1 10 100
Forward Current IF(mA)
Above
characteristic data are
typical data and not a guarantteed data.
Loading...