PREPARED BY: DATE:
ZJ-dtx
/t6 /?7’
T. cleda
DEVICE SPECIFICATION FOR
ELECTRONIC COMPONENTS GROUP
SHARP CORPORATION
s PEC~CATION 1 Opto-Electronic Devices Division
Light Emitting Diode
MODEL No.
I
1. These specification sheets include materials protected under the copyright of Sharp Corporation (“Sharp”).
Please do not reproduce or cause anyone to reproduce them without Sharps consent.
2. When using this product, please observe the absolute maximum ratings and the instructions for use outlined
in these specification sheets, as well as the precautions mentioned below. Sharp assumes no responsibility
for any damage resulting from use of the product which does not comply with the absolute maximum ratings
and the instructions included in these specification sheets, and the precautions mentioned below.
(Precautions)
(1) This products is designed for use in the following application areas;
* OA equipment * Audio visual equipment * Home appliance
* Telecommunication equipment (Terminal) * Measuring equipment
* Tooling machines
L
If the use of the product in the above application areas is for equipment listed in paragraphs
(2) or (3), please be sure to observe the precautions given in those respective paragraphs.
(2) Appropriate measures, such as fail-safe design and redundant design considering
the safety design of the overall system and equipment, should be taken to ensure reliability
and safety when this product is used for equipment which demands high reliability and
safety in function and precision, such as ;
* Transportation control and safety equipment (aircraft, train, automobile etc.)
* Traffic signals
* Other safety equipment
c
(3) Please do not use this product for equipment which require extremely high reliability
and safety in function and precision, such as ;
* Space equipment * Telecommunication equipment (for trunk lines)
* Nuclear power control equipment * Medical equipment
C
(4) Please contact and consult with a Sharp sales representative if there are any questions
regarding interpretation of the above three paragraphs.
* Computers
* Gas leakage sensor breakers * Rescue and security equipment
GL6ZJ27
1
I
1
1
1
3. Please contact and consult with a Sharp sales representative for any questions about this product.
DATE:
CUSTOMER’S APPROVAL.
DATE:
BY: Eiectronic Components Group
PRESENTED BY:
MKatoh,
Department General Manager of
Engineering Dept.,IH
Ooto-Electronic Devices Division
SHARP CORPORATION
MODEL No.
GL6ZT27 Snecification
1. Application
This specification applies to the light emitting diode device Model No. GL6ZJ27.
[AlGalnP (dicing or scribe/brake type)
Grange LED device]
DG996048
GL6Zl27
Jun/16/99
PAGE
l/10 _
2. Outline dimensions and pin connections
3. Ratings and characteristics
. . . . . . . . . . . . . . . . . . . . . ..*................
. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Refer to the attached sheet Page 2.
Refer to the attached sheet Page 3-4.
3- 1. Absolute maximum ratings
3-2. Electra-optical characteristics
3-3. Derating Curve
3-4. Characteristics Diagram
4. Reliability
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*............
Refer to the attached sheet Page 5.
4- 1. Test items and test conditions
4-2. Measurement items and Failure judgement criteria
5. Incoming inspection
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*.........
Refer to the attached sheet Page 6.
5- 1. Applied standard
5-2. Sampling method and level
5-3. Test items, judgement criteria and classifica of defect
54. Test items the surface is be applied for flat type, judgement criteria and classifica of defect
6. Supplement
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ..*...............
6-l. Packing
6-2. Luminous intensity rank
6-3. Dominant wavelength rank
6-4. Environnient
7. Precautions for use
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7- 1. Lead forming method
7-2. Notice of installation
7-3. Soldering Conditions
.7-4. For cleaning
Refer to the attached sheet Page 7-8.
Refer to the attached sheet Page 9- 10.
MODEL No.
IX996048 Jun/16/99
PAGE
2 ~the dimensions and pin
COMeCtionS
Colorless transparency
I
2. 54 OM
i
Pin coMections
0. Anode
0. cathode
iote) Unspecified tol. to be +0&m
rote) Cold rolled steel leads are plated with but the tie-bar cut portions have no plating do not solder this part of the product.
unit
mm
Material
Lead : (Fe) Cold rolled steel
Package : Epoxy resin
Fiih
Lead : Sn plated or wave soldering
Drawing No.
51106029
3. Ratings and characteristics \
(Note 1) Duty ratb=l/lO,Pulse tidth=O. lms
(Note 2) At the position of 1.6mm from the bottom resin package
MODEL No.
DG996048
Junl16l99
PAGE
GL6ZJ27 3110
(Note 3) Refer to the suplement item 6. regarding the standard of rank classification.
3-3. Derating Curve
Peak Forward Current Derating Curve
120
5
- 100
e
-25 0 25 50
Ambient Temperature Ta?C)
1585100
Forward
125
Current Derating Curve
01 I I I I 1
-25 0 25 50
Ambient Temperature Ta("C)
795
I
100 125