General Specification ..................................................................................................................... ... . 3-1
TOC-1
TOC-2Installation Manual
Chapter 1: Introduction
This manual is intended to provide guidance for the proper installation of your printer.
If you require more information to install your printer, consult the User’s Guide
located on the CD-ROM. For further help, please contact your dealer or responsible
representative.
Conventions
The following conventions are used throughout this manual to emphasize certain
procedures or information:
NOTE:A note is a tip or extra information that may be helpful in installing or using the printer.
CAUTION: A caution message provides information that may help you avoid
equipment damage, process failure, or inconvenience. Read all caution
messages carefully.
General Safety Guidelines
Before operating the printer, read the following instructions carefully:
•Follow all the operating procedures provided in this manual.
•Follow all the hazard warnings on the printer and in the manual. Failure to do so
can cause injury to yourself or damage to the printer.
•Do not perform any operation or action in any way other than provided in this
manual. When in doubt, contact your dealer or service company.
•Keep in mind that hazard warnings in this manual or on the printer cannot cover
every possible case, as it is impossible to predict and evaluate all circumstances
beforehand. Be alert and use your common sense.
Safety Precautions
This printer is available in the power specifications 110 V and 230 V. The
specifications that apply to your printer depend on your machine configuration. To
prevent fire or shock hazards, connect the power plug only to a properly rated power
outlet.
WARNING! A warning message indicates the possibility of personal injury if a
specific procedure is not performed exactly as described in the manual. Pay
close attention to these sections and read them fully to prevent possible injury.
1-1
General Safety Guidelines
Introduction
Handling the Printer
•The weight of the printer without toner cartridge and paper is about 22 kg/ 48 lbs. Never
attempt to lift the printer alone.
•To lift the printer, have two individuals facing each other from the front and the rear of the
printer grasp the recessed areas on each side of the printer. Do not lift the printer by
grasping any area other than these recessed areas.
•The machine should be installed near an accessible power outlet for easy connection. For
a complete electrical disconnection, pull out the main plug.
•A small amount of ozone is produced within the printer during operation. The emission
level is insufficient to cause any health hazard. It is advisable to place the printer in a
ventilated area, since the small amount of ozone that is emitted may have an objectionable
odor.
Laser Information for North America
Use of controls or adjustments or performance of
procedures other than those specified herein may result
in hazardous radiation exposure.
TypeDX-B350PDX-B450P
Wave length785nm 785nm
Pulse times6.7us8.2us
Output power0.12mW0.22mW
This Digital Equipment is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 of the
CDRH standards.
This means that the equipment does not produce hazardous laser radiation. For your safety,
observe the precautions below.
•Do not remove the cabinet, operation panel, or any other covers.
•The equipment's exterior covers contain several safety interlock switches. Do not bypass
any safety interlock by inserting wedges or other items into switch slots.
1-2Installation Manual
Printer Orientation
Throughout this manual, the four sides of the printer are referred to as front, rear, right, and left.
The front of the printer is the side near the Operator Panel, and the rear of the printer is opposite
the front. The left and right sides of the printer are defined as the sides to the left and right,
respectively, of a person who is facing the front of the printer.
Warranty
While every effort has been made to make this document as accurate and helpful as possible,
SHARP CORPORATION makes no warranty of any kind with regard to its content. All
information included herein is subject to change without notice. SHARP is not responsible for
any loss or damages, direct or indirect, arising from or related to the use of this operation
manual.
Printer Orientation
Introduction
FCC Regulations state that any unauthorized changes or modifications to
this equipment not expressly approved by the manufacturer could void the
user's authority to operate this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates,
uses and can radiate radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be determined by turning
the equipment off and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the receiver
is connected.
•Consult the dealer or an experienced radio/TV technician for help.
Installation Manual1-3
Warranty
Introduction
Declaration of Conformity
SHARP Laser Printer, DX-B350P/DX-B450P
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
Responsible Party: SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495
TEL: 1-800-BE-SHARP
Notice for Users in the USA
BE SURE TO ASK YOUR AUTHORIZED SHARP DEALER ABOUT THE WARRANTY
THAT YOUR SELLING DEALER EXTENDS TO YOU. In order to assure you, the end-user,
of warranty protection, Sharp extends a limited warranty to each of its authorized dealers and,
in turn, requires each of its authorized dealers to extend its own warranty to you on terms that
are no less favorable than those given to the dealer by Sharp. You should be aware, however,
that Sharp does not itself extend any warranties, either express or implied, directly to you, the
end-user, and no one is authorized to make any representations or warranties on behalf of
Sharp. Specifically, SHARP DOES NOT EXTEND TO YOU, THE END-USER, ANY
EXPRESS WARRANTY OR ANY IMPLIED WARRANTY OF MERCHANTABILITY,
FITNESS FOR USE OR FITNESS FOR ANY PARTICULAR PURPOSE IN CONNECTION
WITH THE HARDWARE, SOFTWARE OR FIRMWARE EMBODIED IN, OR USED IN
CONJUNCTION WITH THIS PRODUCT. Sharp is not responsible for any damages or loss,
either direct, incidental or consequential, which you, the end-user, may experience as a result of
your purchase or use of the hardware, software or firmware embodied in or used in conjunction
with this Product. Your sole remedy, in the event that you encounter any difficulties with this
Product, is against the authorized dealer from which you purchased the Product.
DX-B350P Laser Printer
DX-B450P Laser Printer
In the event that this authorized dealer does not honor its warranty commitments, please contact
the General Manager, Business Products Group, Sharp Electronics Corporation, Sharp Plaza,
Mahwah, New Jersey 07495-1163, so that Sharp can try to help assure complete satisfaction of
the warranty rights to which you are entitled from the authorized dealer.
1-4Installation Manual
Compliance
Warranty
Introduction
Products that have earned the ENERGY STAR
®
are designed to
protect the environment through superior efficiency.
DX-B450P model requires the optional DX-DUX2 duplex module to fully
qualify for ENERGY STAR
®
.
The EcoLogo Program guidelines are applied to only the products in
Canada. The products that meet the EcoLogo Program guidelines carry
the logo shown to the left. The products without the logo may not meet
the EcoLogo Program guidelines.
Installation Manual1-5
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.