Date: Aug. 4, 1994
DUPLEX: SD-3062
1. CHANGES TO THE MATERIALS OF MODE SELECTION GATE
2. IMPROVEMENT OF MARGINS BETWEEN GATE SENSOR PLATE AND PHOTO
SENSOR UP
3. CHANGES TO CENTER TRAY HARNESS
(THIS WAS MADE TO IMPROVE PRODUCTIVITY.)
No. : DTE-180
1. Changes to the materials of mode selection gate
1.Model name: SD-3062
2.General: The mode selection gate used in the finisher had had the curved part in shape and we
corrected it after it had been shaped. We found that it could use by changing its
materials, without correction. Therefore we have made changes of the materials. We
added the washer to the rear side to prevent backlash of the ST upper discharged roller
on the mode selection gate .
3.Description:
ST upper discharged roller
<Change>
Mode selection gate
Materials PC →ABS
Color White →Bright white
4.Action: From mid-July 1994 production
2. Improvement of margins between gate sensor plate and photo sensor up
1.Model name: SD-3062
<Addition>
LX-WZ0042FCZZ
Rear side
2.General: We have carried out to margin up between the photo sensor that controls operation of
the mode selection gate inside the finisher unit and its light proof plate: the gate sensor
plate.
Green
C
SHARP CORPORATION Reprography Division
1/3
3.Description: By changing the forms of the gate sensor plate, we have made margins between it and
the photo sensor up from 0.5 mm to 2.0 mm.
R24 R22.5
0.5mm~ 2.0mm
Photo sensor
4.Action: From the start of July 1994 production
3. Changes to center tray harness (This was made to improve productivity. )
1.Model name: SD-2060, 3062
2.General: We have changed the length and the path of the harness lead wire that is fixed on the
center tray unit to improve productivity.
3.Description:
Suction U11
Fix this point with convex.
➂ Discontinue Convex.
a
Notch
Be careful of the
connector’s direction.
➄ Change the drawing path of solenoids.
➃ Change the drawing direction of snap bands.
Fix the ground connective lead wire.
M4x8 S tight
Let it through inside
D frame R
➀ Fix three ground connective lead
wires at one time. M4x8, Cup screw
Let it through under the frame
➁ Fix it with convex.
Draw it to the arrow direction.
➆ Change the drawing
direction of Snap band.
➅ Let it through the rear side
of the drawer connector.
Caution:
Be sure to fasten Convex and Snap band tightly.
Fix the harness lead wire not
to loosen by snap bands. (Be
careful of the fixing direction)
Let it through the
frame rear side.
➇ Discontinue snap bands.
(On the harness side.)
2/3
parts indicate the operationally changed points in new parts (DHAI-2172FC11).
(From ➀ to ➇)
4.Action: From mid-July 1994 production (Running change)
Ref.
Model
No.
1 SD-3062
2 SD-3062
SD-2060
3
SD-3062
<Interchange>
1. Interc ha ng ea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
spec i fi e d on es fo r m ai n ta in i ng t he s a fe ty and pe rfo r ma nc e o f th e s et .
name
Version P/G No.
53 -6 PGIDM1469FCZ2 PGIDM1469FCZ3 AR
53 — LX-WZ0042FCZZ AA Washer
All
50 -67 LPLTP4514FCZZ LPLTP4514FCZ1 AB
31 -117 DHAI-2172FCZZ DHAI-2172FC11 BF
!
Current parts New parts
Parts code Parts code
5. Interchangeable if replaced with same types of
6. Others .
Price
relate d parts in use .
Parts name
rank
Mode change
gate
Gate sensor
plate
Center tray
harness
Effec-
tive
time
1st lot
’94/7
1st lot
’94/7
1st lot
’94/7
See
text
Inter-
change-
ability
1
— Added
1
1
Note
3/3
Loading...