SHARP DTE176 Technical Report
Date: Jul. 8, 1994
DUPLICATOR: SD-2060
1. CHANGES TO PARTS CODE OF THE CL GEAR INSIDE THE FUSING UNIT IN
ACCORDANCE WITH CHANGE OF THE CLIENT
2. PREVENTION OF FOLDING THE CORNER OF COPIES
3. SET THE ASSEMBLED FELT FOR AUXILIARY CL AS THE SERVICE P ARTS
4. PREVENTION OF THE IRREGULAR NOISE FROM THE COIL FOR COPY LAMPS
No. : DTE-176
1. Changes to parts code of the CL gear inside the fusing unit in accordance with
change of the client
1.Model name: SD-2060, 3062
2.General: The client who has delivered the CL gear inside the fusing unit has been changed.
According to that, we have changed parts code.
3.Action: From the first unit of June 1994 production.
2. Prevention of folding the corner of copies
1.Model name: SD-2060, 3062
2.General: We had attached the duct triangle mylar to the transport unit blowing duct section since
the start of mass production to prevent folding the corner of copies. We discontnued the
duct triangle mylar by padding the ribs of the blowing duct.
You can interchange between the older blowing duct with mylar and the new blowing
duct with the rib padding.
3.Action: From the first unit of June 1994 production.
3. Set the assembled felt for auxiliary CL as the service parts
1.Model name: SD-2060, 3062
2.General: We set the parts assembled the auxiliary CL attachment plate and the felt as the
assembled parts to supply it as the service parts.
Green
SHARP CORPORATION Reprography Division
1/2
C
The auxiliary CL attachment plate
The felt for auxiliary CL
The assembled felt for auxiliary CL
4.Action: From June 1994.
4. Prevention of the irregular noise from the coil for copy lamps
1.Model name: SD-2060, 3062, the 200V series only
2.General: To prevent the irregular noise (buzzing) from the coil for copy lamps inside the AC
circuit PWB, we changed the parts. We would supply new parts after current parts stock
run short because the noise was undisturbed. (You can hear it as far as putting you on
your ears.)
3.Description: (Current) (New)
The heat 70°C resistanc e wax The heat 103°C resistance wax
4.Action: From the first unit of June 1994 production.
Ref.
Model
No.
SD-2060
1
SD-3062
SD-2060
2
SD-3060
SD-2060
3
SD-3062
SD-2060
4
SD-3062
<Interchange>
1. Interc ha ng ea bl e. 4. N ot i nt er ch an ge ab l e.
2. Current type can be used in place of new type.
New type cannot be used in place of current type.
3. Current type cannot be used in place of new type.
New type can be used in place of current type.
Parts marked with “ ” is important for maintaining the safety of the set. Be sure to replace these parts with
specifi e d on es fo r m ai n ta ini ng t he s a fe ty an d pe r fo rmance o f th e s et .
name
Version P/G No.
12 -141 NGERH0946FCZZ NGERH0946FCZ1 AS
15 -45 PDUC-0081FCZZ PDUC-0081FCZ1 AK Blow duct lower 5
All
15 -76
12 — CFLT-0054FC01 AR
200V
83 -15 RCILF0043FCZZ RCILF0043FCZ1 Al Coil [L304]
series
!
Current parts New parts
Parts code Parts code
PSHEP3547FCZZ
(Q’ty: 2)
Effec-
Price
(Discontinued) — Duct sheet 5
5. Interchangeable if replaced with same types of
relate d parts in use .
6. Others .
Parts name
rank
Upper CL gear
(35T-20)
Assembled felt
for auxiliary CL as
tive
change-
time
1st lot
’94/6
’94/6 —
1st lot
’94/6
Interability
Note
1
New
part
1
2/2
Loading...