Page 1
MUSIC SYSTEM FOR iPhone™
MODEL
Thank you for purchasing this SHARP product.
To obtain the best performance from this product, please read this
manual carefully. It will guide you in operating your SHARP product.
DK-AP7P
OPERATION MANUAL
iPod is a registered trademark of
Apple Inc., registered in the U.S. and
other countries.
iPhone is a trademark
of Apple Inc.
Accessories
Please confirm that only the following accessories are included.
AC/DC adaptor
RADPAA059AWZZ
y caserraC
HKASS
Adaptor A x 1 Adaptor B x 1 Adaptor 9 x 1 Adaptor 10 x 1
CG
BSWA571AAV0
iPhone adaptor 12 x 1 iPhone 3G adaptor 15 x 1
CG
1 x
nu( 1 x
)ti
ZZWA051A
D
ASWA832AAV0
y caserra
C
P7PA-KD
BSWA671AAV0CGB
D/CA( 1
x
rotpada doPi -
SWA
812AAV0CGB
rotpada Phonei - P7PA-K
)
rotpada C
ZZWA251AHKASS
SWA
912AAV0CG
ASWA932AAV0CG
Page 2
DK-AP7P
SPECIAL NOTES
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK).
NO USER-SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC
SHOCK, DO NOT EXPOSE THIS APPLIANCE TO RAIN OR
MOISTURE.
“Made for iPod” means that an ele ctronic accessory has been
designed to connect specifically to iPod and has b een certi fied
by the developer to meet Apple performance standards.
“Works with iPhone” means that an e lectronic accessory has been
designed to connect specifical ly to iP hone and h as bee n cert if ied
by the developer to meet Apple pe rfor mance st and ards .
Apple is not responsible for the operation of this device or its
compliance with safety and regulatory standards.
For your assistance in reporting this unit in case of loss or theft,
Important Instruction
please record below the model number and serial number which
are located on the bottom of the unit.
Please retain this information.
FOR YOUR RECORDS
Model number .......................................................
Serial number .......................................................
Date of purchase .......................................................
Place of purchase .......................................................
2
NOTE
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuan t to Part 15 of th e FCC
Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there is no
guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following
measures:
z Reorient or relocate the receiving antenna.
z Increase the separation between the equipment and receiver.
z Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
z Consult the dealer or an experienced radio/TV technician for
help.
WARNING
FCC Regulations state that any unauthorized changes or
modifications to this equipment not expressly approved by the
manufacturer could void the user's authority to operate this
equipment.
Page 3
IMPORTANT SAFETY INSTRUCTIONS
Electricity is used to pe rform many useful fu nctions, but it ca n
also cause personal in jur ies an d pr oper ty dama ge i f impr ope rly
handled. This product has been engineered and manufactured
with the highest priority on safety. However, improper use can
result in electric shock and/or fire. In order to prevent potential
danger, please observe the following instructions when
installing, operating and cl eaning the product. To ensure your
safety and prolong the service life of this product, please read
the following precautions carefully before use.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in accordance
with the manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including amplifiers)
that produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A p olarized plug has two blades with
one wider than the other. A grounding type plug has two
blades and a third grounding prong. The wide blade or the
third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on or pinched
particularly at plugs, convenience re cepta cles, and th e point
where they exit from the apparatus.
11)Only use attachments/accessories specified by the
manufacturer.
12)Use only with the cart, stand, tripod, bracket,
13) Unplug this apparatus during lightning storms or when
14) Refer all servicing to qualified service pe rsonnel. Servicing
Additional Safety Information
15)Power Sources - This product should be operated only from
16)Overloading - Do not overload wall outlets, extensio n co rd s,
17) Object and Liquid Entry - Never push objects of any kind into
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.
unused for long periods of time.
is required when the apparatus has been damaged in any
way, such as power-supply cord or plug is damaged, liquid
has been spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.
the type of power source indicated on the marking label. If
you are not sure of the type of power supply to your home,
consult your product deal er or local power company. For
product intended to operate from battery power, or other
sources, refer to the operating instructions.
or integral convenience receptacles as this can result in a
risk of fire or electric shock.
this product through openings as t hey may t ouch danger ous
voltage points or short-out parts that could result in a fire or
electric shock. Never spill liquid of any kind on the product.
DK-AP7P
Important Instruction
3
Page 4
DK-AP7P
IMPORTANT SAFETY INSTRUCTIONS (continued)
18) Damage Requiring Service - Unplug this product from the
wall outlet and refer servicing to qualified service personnel
under the following conditions:
a) When the AC cord or plug is damaged,
b) If liquid has been spilled, or objects have fallen into the
product,
c) If the product has been exposed to rain or water,
d) If the product does not operate normally by following
the operating instructions. Adjust only those controls
that are covered by the operating instructions as an
improper adjustment of other controls may result in
damage and will often require extensive work by a
qualified technician to restore the product to it s normal
operation,
e) If the product has been dropped or damaged in any
way, and
f ) When the product exhibits a distinct change in
performance - this indicates a need for service.
19)Replacement Parts - When replacement parts are required,
be sure the service techni cian has used repl acement parts
specified by the manufacturer or have the same
characteristics as the original part. Unauthorized
substitutions may result in fire, electric shock, or other
Important Instruction
hazards.
20)Safety Check - Upon completion of any service or repair s to
this product, ask the service technician to perform safety
checks to determine that the product is in proper operating
condition.
21)Wall or ceiling mounting - When mounting the product on a
wall or ceiling, be sure to install the product according to the
method recommended by the manufacturer.
4
22) Power Lines - An outside antenna system should not be
located in the vicinity of overhead power lines or other
electric light or power circuits, or where it can fall into such
power lines or circuits. When installing an outside antenna
system, extreme care should be taken to keep from touching
such power lines or circuits as contact with them might be
fatal.
23)Outdoor Antenna Grounding - If an outside antenna o r cable
system is connected to the product, be sure the antenna or
cable system is grounded so as to provide some protection
against voltage surges and built-up static charges.
Article810 of the National Electrical Code, ANSI/NFPA 70,
provides information with regards to proper grounding of the
mast and supporting structure, grou nding of th e lead- in wir e
to an antenna discharge unit, connection to grounding
electrodes, and requirements for the grounding electrode.
24)Protective Attachment Plug - The product is equipped with
an attachment plug having over load protection. This is a
safety feature. See Instruction Manual for replacement or
resetting of protective device. If replacement of the plug is
required, be sure the service technician has used a
replacement plug specified by the manufacturer that has the
same overload protection as the original plug.
25)Stand - Do not place the product on an unstable car t, st and,
tripod or table. Placing the prod uct on an un st able ba se can
cause the product to fall, resulting in serious personal
injuries as well as damage to the product. Use only a cart,
stand, tripod, bracket or table recommended by the
manufacturer or sold with th e product. When mountin g the
product on a wall, be sure to follow the manufacturer's
instructions. Use only the mounting hardware
recommended by the manufacturer.
Page 5
ENERGY STAR® Program Information
Products that have earned
the ENERGY STAR® are
designed to protect the
environment through
superior energy efficiency.
ENERGY STAR® is a U.S. registered mark.
Contents
General Information
Precautions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Controls and indicators . . . . . . . . . . . . . . . . . . . . . 7
Preparation for Use
System connections . . . . . . . . . . . . . . . . . . . . 8 - 9
Basic Operation
General control . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
iPod and iPhone
Listening to the iPod and iPhone . . . . . . . . .11 - 12
Advanced Feature
Enhancing your system . . . . . . . . . . . . . . . . . . . . 13
References
Troubleshooting chart . . . . . . . . . . . . . . . . . . . . . 14
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
CONSUMER LIMITED WARRANTY . . . Back cover
Page
DK-AP7P
General Information
5
Page 6
DK-AP7P
Precautions
General
z Please ensure that the equipment is
positioned in a well-ventilated area
and ensure that there is at least
4" (10 cm) of free space along the
sides, top and back of the equipment.
z Use the unit on a firm, level surface
free from vibration.
z
Keep the unit away from direct
sunlight, strong magnetic
fields, excessive dust,
humidity and electronic/
electrical equipment (home
computers, facsimiles, etc.)
which generate electrical
General Information
noise.
z Do not place anything on top of the unit.
z Do not expose the unit to moisture, to temperatures higher
than 140°F (60°C) or to extremely low temperatures.
z If your system does not work properly, disconn ect the AC/DC
adaptor from the AC outlet. Plug the AC/DC adaptor back in,
and then turn on your system.
z In case of an electrical storm,
unplug the unit for safety .
4" (10 cm)
6
4" (10 cm)
z Hold the AC/DC adaptor by the
head when removing it from the
AC outlet, as pulling the cord
can damage internal wires.
z The AC/DC adaptor is used as
a disconnect device and shall
always remain readily operable.
z Do not remove the outer
cover, as this may result
in electric shock. Refer
internal service to your
local SHARP service
facility.
z This unit should only be us ed with in the range o f 41°F - 95°F
(5°C - 35°C).
Warning:
The voltage used must be the same as that specified on this
unit. Using this product with a higher voltage other than that
which is specified is dangerous and may result in a fire or other
type of accident causing damage. SHARP will not be held
responsible for any damage resulting from use of this unit with
a voltage other than that which is specified.
Volume control
The sound level at a given volume setting depends on speaker
efficiency, location and various other factors. It is advisable to
avoid exposure to high volume levels, which occurs while
turning the unit on with the volume control setting up high, or
while continually listening at high volumes.
Page 7
Controls and indicators
DK-AP7P
Front View
4
1. iPod Dock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
STEREO SPEAKER
2.1
BUILT-IN SUBWOOFER
1
Y
D-B
AN
T
N/S
2
3
VOL
–
O
VOL
+
2. ESOUND/TV Out Button. . . . . . . . . . . . . . . . . . . . . . 10
3. Volume Down Button . . . . . . . . . . . . . . . . . . . . . . 10
4. Subwoofer Port . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5. ON/STAND-BY Button . . . . . . . . . . . . . . . . . . . . . . .10
6. Volume Up Button . . . . . . . . . . . . . . . . . . . . . . . . . .10
5
6
Back View
1. Video Out Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2. Auxiliary Input Jack . . . . . . . . . . . . . . . . . . . . . . . . .13
Reference page
Reference page
3. DC Input Jack . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
Bottom View
312
The model name/serial no. label (*)
1
1. Battery Compartment . . . . . . . . . . . . . . . . . . . . . . . .9
DK-AP7P
S/NO.
VM
MUSIC SYSTEM
DC IN 6V 2000 mA
6V (UM-3/SUM-3, R6/AA) x4
[DO NOT USE UNSPECIFIED AC ADAPTOR - - -]
MARKETED BY : SHARP ELECTRONICS CORPORATION
SHARP PLAZA, MAHWAH, NEW JERSEY 07495 - 1163
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received,
including interference that may cause undesired operation.
The spec label illustration may be different
from the actual label used.
(*) Label is located at the bottom of the unit.
Reference page
The spec label (*)
MODEL NO.
DK-AP7P
MADE IN MALAYSIA
General Information
7
Page 8
DK-AP7P
Preparation for Use
8
System connections
Make sure to unplug the AC/DC adaptor before making
any connections.
Connecting iPod or iPhone to TV
Photo and video files from iPod or iPhone can be viewed by
connecting the system to TV/monitor.
If the TV/monitor has a video input, connect it to the VIDEO OUT
jack at the back of the unit and set the TV Out on the iPod or
iPhone unit to “ON” position.
TUO OEDIV
Video cable
(not supplied)
T o video
input jack
Watching videos on a TV connected to iPod or
iPhone
1 Enter the iPod or iPhone menu.
Press the ESOUND (TV OUT) button until the ESOUND
LED blinks twice to display video on the TV screen.
2 Select the desire d video from the iPod or iPhone unit.
3 Press the button on the iPod unit to start
playback.
For iPod touch and iPhone, playback will automatically
start once the desired video is selected.
Notes:
z If the TV Out setting is already turned ON at video menu, the
video is automatically displayed on the TV screen when iPod
or iPhone starts playback.
z To return to watching video on iPod or i Ph one scr ee n, r e pea t
steps 1 to 3.
z During iPod or iPhone video pl ayback, pr essing th e ESOUND
(TV OUT) button until the ESOUND LED blinks twice will not
toggle video out display between iPod or iPhone and TV.
VT
z Please make sure to set iPod or iPhone unit to either NTSC
or PAL to match your TV signal. Please visit Apple’s home
page for further information.
z Customer should also refer iPod or iPhone op eration manual
before making video out setting.
Using with the AC/DC adaptor
1 Plug the AC/DC adaptor cable into the DC IN jack on
the unit.
2 Plug the AC/DC adaptor into an AC outlet.
1
AC/DC Adaptor Cable
DC IN Jack
(DC 6V)
2
AC Outlet
(AC 100 - 240 V, 50/60 Hz)
Notes:
z Unplug the AC/DC adaptor from the AC outlet if the unit will
not be used for a prolonged period of time.
z Connecting the AC/DC adaptor to the unit disconnects the
batteries.
z Use only the supplied AC/DC adaptor. Using other AC/DC
adaptor may cause an electric shock or fire.
Page 9
DK-AP7P
Using with the batteries
Use 4 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.
1 Open the battery cover.
Slide the cover in the direction of the arrow.
2
Insert the batteries according to the direction indicated in
the battery compartment.
3
Close the cover.
Note:
Remove the batteries if the unit will not be used for a long period
of time to prevent battery leakage which may cause potential
damage.
Battery replacement:
When batteries are low, sound may become distorted and unit
may automatically turn off during high volume level. Reduce the
volume level or replace the batter ies.
Battery life:
Battery type ALKALINE (AA) (1.5V)
Usage time Approx. 8 hrs.
Output Front 48mW + 48mW
Output Subwoofer 80mW
Note:
Battery life may vary depending on the temperature, battery
types and usage conditions.
Precautions for battery use:
z Installing the batteries incorrectly may cause the unit to
malfunction.
z Insert the batteries according to the direction indicate d in the
battery compartment.
z Remove the batteries if the unit will not be used for a long
period of time. This will prevent potential damage due to
battery leakage.
z When using batteries, the brightness of all illumination light
(indicators) is reduced compared to using AC/DC adaptor.
z Replace all old batteries with new ones at the same time.
z Do not mix old and new batteries.
z Batteries (battery pack or batteries installed) shall not be
exposed to excessive heat such as sunshine, fire or the like.
Caution:
Do not use rechargeable batteries (nickeI-cadmium battery,
etc.).
Changing power source:
Turn off the unit before cha nging the power sour ce. If the 6V DC
power supply is directly plugged in dur ing power on, the unit m ay
automatically enter to stand-by mode. Press the ON/STAND-BY
button again to turn on the unit.
Preparation for Use
9
Page 10
DK-AP7P
Basic Operation
10
General control
STEREO SPEAKER
2.1
BUILT-IN SUBWOOFER
Y
AND-B
T
ON/S
VOL
–
To turn the power on
Press the ON/STAND-BY button to turn the power on. The
POWER and ESOUND indicator will turn on.
After use:
Press the ON/STAND-BY button to enter the power stand-by
mode. The POWER indicator will turn off.
Note:
This unit consumes low current during stand-by mode.
However, please remove the batteries if the unit will not be used
for a long period of time.
VOL
+
Volume control
Press the VOL (+ or –) button to increase or decrease the
volume.
POWER indicator will be blinking when the volume reaches
maximum or minimum level.
ESOUND control
When ON/STAND-BY button is pressed, the ESOUND indicator
turns yellowish orange. You are now in the ESOUND mode,
where low bass and high frequency are automatically adju sted
according to the volume input.
To turn off ESOUND, press the ESOUND (TV OUT) button. The
ESOUND indicator will go off.
Page 11
Listening to the iPod or iPhone
Supported iPod models:
z iPod nano (software 1.2 above)
z iPod mini (software 1.2 above)
th
z iPod (5
generation) (software 1.3 above) (Dock connector
equipped Click Wheel model)
th
z iPod (4
generation) (software 3.0.2 above) (D ock connector
equipped Click Wheel model)
z iPod nano (2
z iPod nano (3
z iPod nano (4
z iPod classic (software 1.0.3 above)
z iPod touch (software 1.1 above)
z iPod touch (2
z iPhone (software 2.2.1 above)
z iPhone 3G (software 2.2.1 above)
Caution:
z Please update your iPod and iPhone unit to the latest
software version before using it. Please visit Apple’s
homepage to download the latest version for your iPod and
iPhone.
Notes:
z Once the iPod or iPhone is connected to the unit it will begin
charging when AC/DC adaptor is used.
z The iPod or iPhone unit will not be charged while the main
unit use the batteries as power supply.
nd
generation) (software 1.0.0 above)
rd
generation) (software 1.0.3 above)
th
generation) (software 1.0.3 above)
nd
generation) (software 2.1 above)
iPod or iPhone adaptor connection
Choose adaptor that fits your iPod or iPhone. Your iPod or iPhone
will fit snuggly into the correct adaptor. If your iPod is not mentioned
below, an iPod adaptor may have been included with your iPod
unit.
The marking shows which
iPod or iPhone fits
iPod
Adaptor No.
iPod or iPhone
Description
9 5G iPod (with video)
9 U2 iPod with video
9 iPod classic
10 5G iPod with video
10 iPod classic
A iPod mini
A 4G iPod & U2 iPod
A iPod photo & Color U2 iPod
A iPod with color display
B 4G iPod
B iPod photo
B iPod with color display
12 iPhone
15 iPhone 3G
Notes:
z iPod nano (2
nano (4th generation), iPod touch and iPod touch (2nd
generation) are not compa tible with the i Pod adapt ors lis ted
above. Please use the adaptor suppli ed wi th your iPo d uni t.
z If you have an iPod that does not have an iPod 30 Pin conn ector,
you can use an audio cable to con nect i t to th e AUX IN jack.
nd
generation), iPod nano (3rd generation), iPod
9
Capacity
30GB
30GB
80GB, 120GB
60GB & 80GB
160GB
4GB & 6GB
20GB
20GB & 30GB
20GB
40GB
40GB & 60GB
60GB
4GB & 8GB & 16GB
8GB & 16GB
DK-AP7P
iPod and iPhone
11
Page 12
DK-AP7P
Listening to the iPod or iPhone (continued)
To insert iPod or iPhone adaptor
1. Insert the adaptor into unit and connect your iPod or iPhone .
iPhone (bottom)
Dock connector
iPhone
iPod or iPhone playback
1 Press the ON/STAND-BY button to turn the power on.
2 Insert iPod or iPhone unit in the dock of main unit.
3 Press the button on the iPod unit to start
playback.
For iPod touch or iPhone, playback will automatically
start once the desired file is selected.
iPhone
iPhone adaptor
iPhone dock
iPod and iPhone
iPhone connector
Caution:
Unplug all accessories for the iPod or iPhone before inserting it
into the dock.
To remove iPod
or iPhone adaptor
Insert the tip of a screwdriver
(“-” type, small) into the adaptor
hole as shown and lift upward to
remove.
12
iPod adaptor
To disconnect iPod or iPhone
Simply remove the iPod or iPho ne from t he do ck. It is sa fe to do
so even during playback.
Page 13
Enhancing your system
The audio cable is not included. Purchase a separate audio
cable as shown below.
Portable audio
player
NI XUA
Computer
To the line
output jack
Audio cable
(not supplied)
Listening to the audio/video sounds from por-
table audio player, computer, etc.
1 Use Audio cable to connect the portable audio
player, computer etc. to the AUX IN jack.
When using video equipment, conne ct the au dio output
to this unit and the video output to a television.
2 Press the ON/STAND-BY button to turn the power
on.
3 Play the connected equipment.
If volume level of the connected device is too high,
sound distortion may occur. Should this happen, lower
the volume of the connected device.
Notes:
z To prevent noise interference, place the unit away from the
television.
z Make sure to undock the iPod or iPhone before makin g any
connections to AUX IN. Otherwise, sound from AUX IN will
not be heard.
DK-AP7P
Advanced Feature
13
Page 14
DK-AP7P
References
14
Troubleshooting chart
Many potential problems ca n be r eso lved b y t h e own e r wi th out
calling a service technician.
If something is wrong with this product, check the following
before calling your authorized SHARP dealer or service center.
General
Symptom Possible cause
z When a button is
pressed, the unit does
not respond.
z No sound is heard. z Is the volume level set to
iPod and iPhone
Symptom Possible cause
z No sound is produced.
No image appears on the
TV/monitor.
z iPod or iPhone will not
charge.
z Set the unit to the power
stand-by mode and then
turn it back on.
minimum?
z The iPod or iPhone is not
playing.
z The iPod or iPhone is not
properly connected to the
unit.
z Is the AC/DC adaptor of the
unit plugged in?
z The video cable is not
properly connected.
z The TV/monitor’s input
selection is not properly set.
z The iPod or iPhone is not
making full contact with the
connector.
z The main unit is using
batteries as power supply.
rd
z Using 3
generation iPod.
Condensation
Sudden temperature changes, storage or operation in an
extremely humid environment may cause condensation inside
the cabinet.
Condensation can cause the unit to malfunction. If this happens,
leave the power on until normal play back is possible (about 1
hour) before operating the unit.
If problem occurs
When this product is subjected to strong external interference
(mechanical shock, excessive static electricity, abnormal s upply
voltage due to lightning, etc.) or if it is operated incorrectly, it
may malfunction.
If such a problem occurs, do the following:
1 Set the unit to the stand-by mode and turn the power on
again.
2 If the unit is not restored in the previous operation, unplug
and plug in the unit, and then turn the power on.
Before transporting the unit
Undock the iPod or iPhone and close the unit. The unit will
automatically enter stand-by mode.
CAUTION: Carrying the unit with iPod or iPhone docked might
damage both systems.
Page 15
Maintenance
DK-AP7P
Cleaning the unit
Periodically wipe the unit with a clean soft cloth.
Caution:
z Do not use chemicals for cleaning (gasoline, paint thinner,
etc.). It may damage the unit finishing.
z Do not apply oil to the inside of the unit. It may cause
malfunctions.
Specifications
As part of our policy of continuous improvement, SHARP
reserves the right to make design and specificat io n cha ng es for
product improvement without prior notice. The performance
specification figures indicated are nominal values of production
units. There may be some deviations from these values in
individual units.
General
Power source DC IN 6V 2000mA: AC/DC adaptor
Power
consumption
Output power Front speakers:
(AC 100 - 240 V ~ 50/60 Hz)
DC IN 6V [ “AA” size (UM/SUM-3,
R6 or HP-7) battery x 4]
P W
1.2 watts minimum RMS per channel
into 8 ohms from 100 Hz to 20 KHz, 10%
total harmonic distortion.
Subwoofer:
2 watts minimum RMS into 4 ohms from
50 Hz to 120 Hz, 10% total harmonic
distortion.
Speaker 2.1-way type speaker system
Speaker maximum
input power
Speaker rated
input power
Output terminals Video output: 1Vp-p
Input terminals Auxiliary (aud io signal):
Dimensions Width: 7-4/5" (198 mm)
Weight 1.4 lbs. (0.62 kg)
Front speaker: 1-1/8" (3.0 cm)
Subwoofer: 1-3/4" (4.6 cm)
Front speaker: 2.0 W/Channel
Subwoofer: 4 W
Front speaker: 1.2 W/Channel
Subwoofer: 2 W
500 mV/47 k ohms
Height: 2-7/10" (69.8 mm)
Depth: 3" (77 mm)
References
15
Page 16
CONSUMER LIMITED WARRANTY
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand product (the “Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option, either repair the defect or replace the defective Product or part thereof
with a new or remanufactured equivalent at no charge to the purchaser for parts or labor for the period(s) set forth below.
This warranty does not apply to any appearance items of the Product nor to the additional excluded item(s) set forth below nor
been damaged or defaced, which has been subjected to improper voltage or other misuse, abnormal service or handling, or which has been altered or modified in
design or construction.
In order to enforce the rights under this limited warranty, the purchaser should follow the steps set forth below and provide proof of purchase to the servicer.
The limited warranty described herein is in addition to whatever implied warranties may be granted to purchasers by law. ALL IM
THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR USE ARE LIMITED TO THE PERIOD(S) FROM THE DA TE OF PURCHASE SET FORTH BELOW
Some states do not allow limitations on how long an implied warranty lasts, so the above limitation may not apply to you.
Neither the sales personnel of the seller nor any other person is authorized to make any warranties other than those described
warranties beyond the time period described herein on behalf of Sharp.
The warranties described herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive
Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all liabilities and responsibilities of Sharp to the
purchaser with respect to the Product, and shall constitute full satisfaction of all claims, whether based on contract, negligence, strict liability or otherwise. In no event
shall Sharp be liable, or in any way responsible, for any damages or defects in the Product which were caused by repairs or attempted repairs performed by anyone
other than an authorized servicer. Nor shall Sharp be liable or in any way responsible for any incidental or consequential economic or property damage. Some states
do not allow the exclusion of incidental or consequential damages, so the above exclusion may not apply to you.
THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS WHICH VARY FROM STATE TO STATE.
Model Specific Section
Y
our Product Model Number & Description:
Warranty Period for this Product: One (1) year parts and labor from the date of purchase.
Additional Item(s) Excluded from W
Where to Obtain Service:
What to do to Obtain Service:
arranty Coverage (if any): Non-functional accessories, supplies, and consumable items.
DK-AP7P Music System for iPhone
(Be sure to have this information available when you need service for your Product.)
At a Sharp Authorized Servicer located in the United States.
To find a location of the nearest Sharp Authorized Servicer , call Sharp toll free at 1-800-BE-SHARP.
Ship prepaid or carry in your Product to a Sharp Authorized Servicer.
Be sure to have Proof of Purchase
packaged securely.
available. If you ship the Product, be sure it is insured and
to any Product the exterior of which has
PLIED WARRANTIES INCLUDING
herein, or to extend the duration of any
remedy available to the purchaser.
TO OBTAIN SUPPLY, ACCESSOR Y OR PRODUCT INFORMATION, CALL 1-800-BE-SHARP.
SHARP ELECTRONICS CORPORATION
Sharp Plaza, Mahwah, New Jersey 07495 - 1163
Printed in Malaysia
TINSEA297AWZZ
09F R KI 1
.
Loading...