Sharp DK-AP2 User Manual
MODEL
DK-AP2
MUSIC SYSTEM FOR iPod
This quick Start Guide will help you to correctly install and operate your system.
Illustration printed in this quick guide are for the model DK-AP2.
Accessories
Remote control x 1
AC power lead x 1 iPod adaptor x 8
AC/DC adaptor x 1
RADPAA039AWZZ (DK-AP2)
RADPAA036AWZZ (DK-AP2(BK))
Remote control battery installation
Use the “CR 2025”, coin lithium battery.
Before using remote control
Before using remote control, please remove plastic shield
at battery holder.
Plastic shield
Remote control
Battery holder
1 Whilst pushing the locking tab towards the centre of the remote control, slide out the battery holder.
Back of remote control
Locking tab
2 Remove the old battery from the battery holder, insert the new battery and then slide the battery holder back into the
remote control.
Battery holder
Positive (+) side up
Polarity (+) symbol
Locking tab
Battery type
TINSEA197AWZZ
07G R MW
2
DC IN 6V
AUX IN
VIDEO
OUT
Power source
HH
H Using with the AC/DC adaptor
HH
1 Plug the AC power lead into the AC/DC adaptor.
2 Plug the AC/DC adaptor cable into the DC Input socket on
the unit.
Listening to the iPod
HH
H
To insert iPod adaptor
HH
1 Insert the iPod adaptor into unit and connect your
iPod.
3 Plug the AC power lead into a wall socket and switch on
the power supply. The STAND-BY indicator turns red and
when the power is on, the POWER indicator turns blue.
AC/DC Adaptor Cable
DC INPUT socket
(DC 6V)
AC Power Lead
AC/DC Adaptor
Wall Socket
(AC 110 - 240 V, 50/60 Hz)
HH
H Using with the batteries
HH
VIDEO
OUT
DC IN 6V
AUX IN
1 Disconnect the AC/DC adaptor, and open the battery
compartment.
iPod (bottom)
iPod
Dock connector
iPod adaptor
iPod dock
iPod connector
HH
H To remove iPod adaptor
HH
D
2
K
P
-
A
M
U
S
M
I
C
E
T
S
S
Y
+
L
O
V
-
Y
B
-
D
N
A
T
S
/
N
O
Insert the tip of a screwdriver (“–” type, small) into the iPod
adaptor hole as shown and lift upward to remove.
2 Insert 4 “AA” size batteries (UM-3, R6 or similar) into the
battery compartment.
+
1
3
2
+
+
+
4
3 Close the battery compartment.
4 The STAND-BY indicator will turn red.
Remove the batteries if the unit is not to be used for long
period of time to prevent battery leakage which may cause
potential damage.
When using batteries, the brightness of all illumination light
(indicators) is reduce compared to using AC/DC adaptor.
Turn on your system
Press the ON/STAND-BY button to turn the power on. The
POWER indicator turns blue to indicate power on.
E
SOUND
STAND-BY
HH
H iPod playback
HH
Note:
Do not connect the Audio cable to AUX IN socket during iPod
playback. Otherwise, sound from the iPod will not be heard.
1 Press the ON/STAND-BY button to turn the power on.
2 Insert iPod unit in iPod dock of main unit.
00
6 6
0
/
Press the
to start playback.
6 button if the iPod unit is in pause mode
00
6 6
iPod
iPod adaptor
+
L
O
V
-
Y
-B
D
N
TA
S
/
N
O
2
D
K
P
-
A
M
U
S
M
I
C
E
T
S
S
Y
HH
H To disconnect iPod
+
L
- VO
ON/STAND-BY
2
D
P
K
A
-
M
M
E
U
T
S
S
I
C
Y
S
-
-
HH
Simply remove the iPod from the iPod dock. It is safe to do
so even during playback.
Loading...