Sharp CD-XP120H User Manual

CD-XP120H

2 Remote control battery installation

Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.

MINI COMPONENT SYSTEM

This Quick Guide will help you to correctly install and operate
your system.

If you require any advice or assistance regarding
your Sharp product, please visit our web-site
www.sharp.co.uk/support.
Customers without Internet access may telephone
08705 274277 during office hours (or [phone]
if telephoning from Ireland).

0101

1 Accessories

Remote

control × 1

AM loop aerial

× 1

FM aerial × 1 AC power lead

× 1

1 Remove the battery cover.

2 Insert the batteries as shown.

3 Replace the cover.

3 Removing the transport screw

Before turning the power on, be
sure to remove this transport
screw on the back of the unit us­ing a flat head screwdriver or a
coin.

Transport screw

CDXP120HE_QG 02.4.10, 6:34 PM1

– 1 –

TINSE0104SJZZ
02D N TO 1

4 System connections

5 Turn on your system

AM loop aerial

Right speaker

Wall socket
(AC 230 V, 50 Hz)

FM aerial

Left speaker

The first time the unit is plugged in, the
unit will enter the demonstration mode.
You will see words scroll.

1 Press the EQUALIZER/X-BASS/

DEMO button to cancel the demon­stration mode.

2 Press the ON/STAND-BY button to

turn the power on.

CDXP120HE_QG 02.4.10, 6:34 PM2

Plain

White line

– 2 –

Listening to a CD (CDs)

1 Press the CD button.
2 Press the
3 Place the CD(s) on the disc tray, label side up.

When loading a third disc, press the DISC SKIP button to turn the
disc tray, then place the CD in the open position.

7 7

7 OPEN/CLOSE button to open the disc tray.

7 7

12 cm (5") 8 cm (3")

Listening to the radio

1 Press the TUNER (BAND) button repeatedly to select the desired

frequency band (FM or AM).

XX

2 Press the TUNING (

When the TUNING button is pressed for more than 0.5 seconds, scan­ning will start automatically and the tuner will stop at the first re­ceivable broadcast station.

To receive an FM stereo transmission:

Press the TUNER (BAND) button to display the “ST” indicator.

● “j” will appear when an FM broadcast is in stereo.

WW

X or

W) button to tune in to the desired station.

XX

WW

4 Press the

7 7

7 OPEN/CLOSE button to close the disc tray.

7 7

5 To select the CD you want to listen to first, press one of

buttons on the remote control.

6 Press the

CDXP120HE_QG 02.4.10, 6:34 PM3

0 / R 0 / R

0 / R button to start playback.

0 / R 0 / R

ss

s 1 -

ss

ss

s 3

ss

FM stereo mode indicator

FM stereo receiving indicator

– 3 –

Listening to a cassette tape

H H

1 Press the
2 Load a cassette into the TAPE 1 or TAPE 2 cas-

sette compartment with the side to be played fac­ing toward you.

3 Press the TAPE button.
4 Press the

■

If trouble occurs

When this product is subjected to strong external interference (mechani­cal shock, excessive static electricity, abnormal supply voltage due to light­ning, etc.) or if it is operated incorrectly, it may malfunction.

If such a problem occurs, do the following:

1. Set the unit to the stand-by mode and turn the power on again.

2.

If the unit is not restored in the previous operation, unplug and
plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by reset­ting it.

7 7

H

7 button to open the cassette door.

H H

7 7

TAPE 1

0 0

0 button of TAPE 1 or TAPE 2 to start playback.

0 0

TAPE 2

■

Clearing all the memory (reset)

1. Press the ON/STAND-BY button to enter the power stand-by
mode.

2.

Whilst pressing down the TUNER (BAND) button and the DISC
SKIP button, press the ON/STAND-BY button until “CLEAR” ap­pears.

Caution:

This operation will erase all data stored in memory including clock, timer
settings, tuner preset, and CD programme.

■

Maintenance

● Dirty heads, capstans or pinch rollers can cause poor sound and tape
jams. Clean these parts with a cotton swab moistened with commercial
head/pinch roller cleaner or isopropyl alcohol.

● When cleaning the heads, pinch rollers, etc., unplug the unit which
contains high voltages.

C

B

TAPE 1

TAPE 2

● After long use, the deck’s heads and capstans may become magnetised,
causing poor sound. Demagenetise these parts once every 30 hours
of playing/recording time by using a commercial tape head
demagnetiser. Read the demagnetiser’s instructions carefully before
use.

● Clean the dust or stain on the CD pickup lens using a commercial clean­ing disc (brush type).

A

C

E

A Erase head

D

B Recording/

C Capstan

D

D Pinch roller
E Playback head

Playback head

CDXP120HE_QG 02.4.10, 6:34 PM4

– 4 –