Sharp CD-SW300H, CD-SW330H User Manual

MODEL

CD-SW300H/CD-SW330H

MINI COMPONENT SYSTEM

This quick Start Guide will help you to correctly install and
operate your system.

Illustration printed in this quick guide are for the model CD-SW300H.

2

Remote control battery installation

1

Accessories

Remote control × 1

FM aerial × 1

3

System connections

Right speaker

AM loop aerial × 1

FM aerial

Use 2 “AA” size batteries (UM/SUM-3, R6, HP-7 or similar).
Batteries are not included.

1 Open the battery cover.

2 Insert the batteries as shown.

3 Close the cover.

AM loop aerial

Left speaker

Subwoofer

Purple

Red

Black

AC INPUT

Red

Black

4

Turn on your system

The first time the unit is plugged in, the unit will enter the demonstration mode.

You will see words scroll.

Wall socket
(AC 230 V, 50 Hz)

Speaker light-up wire

1 Press the X-BASS(SURROUND)/DEMO button to cancel the demonstration mode.

ANTENNA

FM

GND

AM

75 OHMS

Subwoofer light-up wire

2 Press the ON/STAND-BY button to turn the power on.

TINSEA179AWZZ
07C R KI 1

Listening to the radioListening to a CD or MP3/WMA disc

1 Press the CD button.

2 Press the 1 button and within 5 seconds, press the button to

open the disc tray 1.

3 Place the disc on the disc tray 1, label side up.

12 cm (5”)

8 cm (3”)

4 Press the button to close the disc tray 1.

5 You can place discs on trays 2 - 5 by following steps 2 - 4.

6 Press the / button to start playback.

Listening to a cassette tape

FM stereo mode indicator

FM stereo receiving indicator

1 Press the TUNER (BAND) button repeatedly to select the desired

frequency band (FM or AM).

2 Press the TUNING ( or ) button to tune in to the desired station.

When the TUNING ( or ) button is pressed for more than 0.5 sec­onds, scanning will start automatically and the tuner will stop at the
first receivable broadcast station.

To receive an FM stereo transmission:
Press the TUNER (BAND) button to select stereo mode and “ST”
indicator will be displayed.

“ ” will appear when an FM broadcast is in stereo.

If trouble occurs

When this product is subjected to strong external interference (me­chanical shock, excessive static electricity, abnormal supply voltage
due to lightning, etc.) or if it is operated incorrectly, it may malfunction.

If such a problem occurs, do the following:

1. Set the unit to the stand-by mode and turn the power on again.

2. If the unit is not restored in the previous operation, unplug
and plug in the unit, and then turn the power on.

Note:

If neither operation above restores the unit, clear all the memory by
resetting it.

1 Open the cassette compartment by

pushing the area marked “ ”.

2 Load a cassette into the TAPE 1 compartment

or TAPE 2 compartment with the side to be
played facing towards you.

TAPE 1

TAPE 2

3 Press the TAPE (1 2) button to select the cassette you want to

listen to.

4 Press the / (TAPE ) button to start playback.

Clearing all the memory (reset)

1. Press the ON/STAND-BY button to enter the power stand-by
mode.

2. Whilst pressing down the button and the
the TUNER (BAND) button until “CLEAR ALL” appears.

Caution:

This operation will erase all data stored in memory including clock,
timer settings, tuner preset, and CD programme.

77

7 button, press

77

Maintenance

Routine maintenance is required for continued optimum perfor­mance, refer to the operation manual.