Sharp BL773CO User Manual

Download

Mega Kitchen System

BL773CO

OWNER’S GUIDE

www.ninjakitchen.com

1-877-646-5288

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only

WHEN USING ELECTRICAL APPLIANCES, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING:

READ ALL INSTRUCTIONS BEFORE USING YOUR NINJA® MEGA KITCHEN SYSTEM®.

POLARIZED PLUG WARNING: To reduce the risk of electric shock,

this appliance has a polarized plug (one blade is wider than the other). This plug will ﬁt into a polarized outlet only one way. If the plug does not ﬁt fully into the outlet, reverse the plug. If it still does not ﬁt, contact a qualiﬁed electrician to install the proper outlet. DO NOT modify the

plug in any way.

CAUTION: Blade assemblies are sharp, handle with care. When handling the blade assemblies, always hold by the shaft.

WARNING:

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR INJURY:

1. To protect against electrical shock, do not submerge the appliance or allow the power cord to come into contact with water or any other liquid.

2. DO NOT allow young children to operate the appliance or use as a toy. Close supervision is necessary when any appliance is used by or near children.

3. Never leave an appliance unattended when in use.

4. Turn the appliance Off and remove the power cord from the electrical outlet when not in use, before assembling or disassembling parts and before cleaning. To unplug, grasp the plug and pull from the electrical outlet. Never pull from the power cord.

5. DO NOT abuse the power cord. Never carry the appliance by the power cord or yank it to disconnect from electrical outlet; instead grasp the plug and pull to disconnect.

6. DO NOT operate any appliance with a damaged cord or plug, or after the appliance malfunctions, has been dropped or damaged in any manner. This appliance has no serviceable parts. Return the appliance to EURO-PRO Operating LLC for examination, repair or adjustment.

7. DO NOT let the power cord hang over the edge of table or counter or touch hot surfaces such as the stove.

8. Always use appliance on a dry, level surface.

Euro-Pro, Mega Kitchen System, Nutri Ninja, and Ninja are trademarks of Euro-Pro Operating LLC.

TOLL FREE: 1-877-646-5288

9. Keep hands, hair, clothing, as well as utensils out of container while processing to reduce the risk of severe injury to persons or damage to the appliance. A scraper may be used but only when the appliance is not running.

10. CAUTION: Blade assemblies are sharp,

handle with care. When handling the blade assemblies, always hold by the shaft.

11. Avoid contact with moving parts.

12. DO NOT attempt to sharpen blades.

13. DO NOT use the appliance if blade assembly is bent or damaged.

14. To reduce risk of injury, never place the blade assembly on base without pitcher or bowl properly attached.

15. DO NOT operate this appliance on or near any hot surfaces (such as gas or electric burner or in a heated oven).

16. The use of attachments or accessories including canning jars, not recommended by the manufacturer may result in ﬁre, electric shock or personal injury.

17. DO NOT remove the container from the motor base while the appliance is in operation.

18. To reduce the risk of injury, NEVER operate the appliance without the lid in place; DO NOT try to defeat the interlock mechanism; make sure that the blade assembly is properly installed before operating the appliance.

19. DO NOT expose containers to extreme temperature changes.

20. CAUTION: DO NOT PROCESS HOT FOODS OR

HOT LIQUIDS

21. DO NOT overﬁll.

22. Never feed food by hand when using the food processor. Always use the food pusher.

23. DO NOT operate the appliance empty.

24. To reduce the risk of burns, always allow the appliance to cool before taking off parts and before cleaning.

25. In the event that the unit overheats, the control panel lights will ﬂash and the unit will shut down. Unplug the unit and wait 15 minutes to reset.

26. THIS PRODUCT IS INTENDED FOR HOUSEHOLD USE ONLY. Do not use this appliance for anything other than its intended use. Do not use outdoors.

27. The maximum rating is based on the Stacked Blade Assembly (pitcher) that drives the greatest power and other recommended attachments may draw signiﬁcantly less power or current.

WARNING: Extension cords are not

recommended for use with this product.

SAVE THESE

INSTRUCTIONS

TECHNICAL SPECIFICATIONS

Voltage: 120V., 60Hz. Power: 1500 Watts Pitcher Capacity: 72 oz. (9 cups, 2.1 L) Bowl Capacity: 64 oz. (8 cups, 1.9 L) Nutri Ninja® Capacity: 16 oz. (2 cups, 470 mL)

www.ninjakitchen.com

Contents

Thank you for purchasing

the Ninja Mega Kitchen System®.

Getting to Know Your Ninja® Mega Kitchen System® ............................................................3

Using the Ninja

Mega Kitchen System® ...........................................................................4

Assembly and Use for the 72 oz. Pitcher .............................................................................5

Assembly and Use for the Nutri Ninja

Cup .........................................................................7

Assembly and Use for the 64 oz. Bowl ................................................................................8

Assembly and Use for the Disc Attachments .....................................................................10

Speed Setting & Uses ......................................................................................................11

Care & Maintenance .......................................................................................................12

Troubleshooting Guide .....................................................................................................13

Replacement Parts ..........................................................................................................13

Warranty & Registration ...................................................................................................14

Getting To Know Your Ninja® Mega Kitchen System

Nutri Ninja

Food Processor Bowl Dough

Cup (x3)

To-Go Lid

(x3)

Chopping

Blade

Nutri Ninja®

Blade Assembly

Spindle for

Discs

Feed Chute Lid with

Two Part Pusher

Grating

Disc

Reversible Slicing/

Shredding Disc

Pitcher Lid72 oz. Pitcher

NOTE: Blade assemblies are not interchangeable. NOTE: All jars, lids, discs and blades are dishwasher safe.

All jars, lids and plastic components of blade and disc assemblies are BPA free.

TOLL FREE: 1-877-646-5288

Assembly (Pitcher)

Motor BaseStacked Blade

CAUTION: Blade assemblies are sharp, handle with care. When handling the blade assemblies, always hold by the shaft.

Using the Ninja® Mega Kitchen System

PLEASE KEEP THESE IMPORTANT SAFEGUARDS IN MIND WHEN USING THE APPLIANCE:

IMPO RTANT: Never add ingredients into the

container before placing the attachment in ﬁrst.

IM POR TA NT: Attachments are not

interchangeable.

CAUTION: Blades are sharp! Use extreme

caution when handling the blade assemblies. Always hold them by the shaft.

IMPORTANT: DO NOT attempt to operate the

appliance without the lid on.

IM POR TA NT: Never run the appliance empty.

CAUTION: DO NOT PROCESS HOT FOODS OR

HOT LIQUIDS.

CAUTION: Never remove the container while

the appliance is still running.

WARNING: Never leave the appliance

unattended while in use.

CAUTION: Blades

are not locked in place. If using the pour spout, ensure the lid is fully locked onto the blender pitcher.

CAUTION: Blades

are not locked in place. If pouring with the lid removed, ALWAYS remove the blade assembly ﬁrst.

BEFORE FIRST USE

CAUTION: Blade assemblies are sharp, not locked

in place and removable, handle with care. When handling the blade assemblies, always hold them by the shaf t.

1 Remove all packaging material and labels from the

appliance.

2 Wash the lids, pitcher, bowl, Nutri Ninja

blade assemblies in warm, soapy water with a soft cloth. Use caution when washing the blade

assemblies as the blades are very sharp.

3 Rinse and dry thoroughly.

4 The pitcher, bowl, Nutri Ninja

assemblies are all dishwasher safe. It is recommended that the lids and blade assemblies be placed on the top rack. Ensure that the blade assemblies are removed from the containers before placing in the dishwasher.

5 Wipe the motor base clean with a damp cloth.

cups and

cups, lids and blade

www.ninjakitchen.com

Assembly and Use for the 72 oz. Pitcher

Assembly

Fig. 1

Fig. 2

CAUTION:

IM POR TA NT: Make sure that the motor base is plugged

1 Place the motor base on a clean, dry, level surface such

2 Align and lower the pitcher onto the motor base. ( Fig. 1)

3 Rotate the pitcher clockwise as far as it will go to lock in

4 The pitcher can be placed on the motor base two ways;

5 Holding the Stacked Blade Assembly by the top of the

Blade assemblies are sharp, not locked in place and removable, handle with care. When handling the blade assemblies, always hold them by the shaf t.

in for use.

as a counter or table top.

Handle should be aligned slightly to the right of the “LOCK” symbol on the motor base.

place. (Fig. 2)

the handle can be on the front right corner or the front left corner. (Fig. 3a, Fig. 3b)

shaft, place it onto the drive gear inside the pitcher. Ensure that the standing upright. (Fig. 4)

blade assembly

is seated properly and is

Fig. 3a

Fig. 3b

Fig. 4

Fig. 5

NOTE: The Stacked Blade Assembly will ﬁt loosely on the

drive gear.

6 Add the ingredients to the pitcher, making sure that they

do not exceed the highest measured marking line on the side of the pitcher.

7 Holding the lid by the handle in the upright position, place

it on top of the pitcher aligning the arrow ( ) located on the lid with the arrow ( ) located on the pitcher’s handle.

(Fig. 5) Press the handle down until you hear a click.

8 Plug the power cord into the electrical outlet and press

the power button ( ).

NOTE: As a safety feature, the power button

( ) will ﬂash and the motor will not work if the pitcher and lid are not installed correctly. When the pitcher and lid are installed properly, the power but ton ( ) will be solid, indicating that the appliance is ready for use.

TOLL FREE: 1-877-646-5288

WARNING: Never leave the appliance unattended while in use.

USE

Fig. 6 Fig. 8

9 Select the speed that best suits your needs. (Fig. 6)

NOTE: Pulse ingredients for even chopping by pressing

down in short intervals.

10 When you have reached your desired consistency, stop

the appliance by pressing the power button ( wait for the blade assembly to stop turning. (Fig. 7)

11 To remove the lid, press the release button on the lid,

pull the lid handle up to a 90° angle and lift the lid off. Turn the pitcher counter clockwise and then lift off the base. (Fig. 7, Fig. 8)

CAUTION: Never insert your hands in the pitcher as the blades are sharp. Always use a spatula to

dislodge food that has stuck to the sides of the pitcher.

Fig. 7

) and

REMOVAL

12 Depending on the consistency of the contents in the

container, open the pour spout cap and use the spout to empty liquid contents. For thicker consistencies, remove the lid and blade assembly carefully (by its shaft), then empty contents from the container.

13 Make sure that the unit is unplugged when not in use.

CAUTION: Blades are not locked

in place. If using the pour spout, ensure that the lid is fully locked onto the blender pitcher.

CAUTION: Blades are not

locked in place. If pouring with the lid removed, ALWAYS remove the blade assembly ﬁrst before pouring.

www.ninjakitchen.com

Assembly and Use for the Nutri Ninja® Cup

WARNING: Never leave the appliance unattended while in use.

ASSEMBLY PULSE

Fig. 1 Fig. 2

For best results, use short “PULSES”... Practice makes perfect!!

Use caution when handling the blade

assemblies.

IM POR TA NT: Make sure that the motor base is

plugged in for use.

1 Place the motor base on a clean, dry, level surface

such as a counter or table top.

2 Add ingredients to the Nutri Ninja

3 Place the Nutri Ninja

blade onto the cup and screw it

tightly until you have a good seal. ( Fig. 1)

4 Turn the Nutri Ninja

cup upside down and place it onto the motor base, aligning the tabs on the cup with the motor base. Turn the Nutri Ninja® cup clockwise until you hear a click. (Fig. 2) Turn the power button on, the Nutri Ninja® button will illuminate.

5 Press down on the Nutri Ninja

button in short intervals

to activate. (Fig. 3)

Fig. 3 Fig. 4 Fig. 5

cup.

REMOVAL

6 Once you have reached your desired consistency,

turn the power button off. Turn the Nutri Ninja® cup counterclockwise and pull straight up to remove.

(Fig. 4) (Fig. 5)

NOTE: Do not over ﬁll! To avoid spilling, do not add

ingredients past the “Max” ﬁll line.

cup, twist

blade

7 Turn the cup upright and remove the Nutri Ninja

by twisting the blade assembly counterclockwise.

8 Place the To-Go lid onto the Nutri Ninja

clockwise to seal and enjoy!

9 Make sure that the motor base is unplugged when not

in use.

NOTE: To order additional Nutri Ninja

Cups, please visit our website: www.ninjakitchen.com or feel free to contact customer service: 1-877-646-5288.

TOLL FREE: 1-877-646-5288

Assembly and Use for the 64 oz. Bowl

WARNING: Never leave the appliance unattended while in use.

ASSEMBLY

Fig. 1

Fig. 2

Use caution when handling the blade assemblies.

IM POR TA NT: Make sure that the motor base is

plugged in for use.

1 Place the motor base on a clean, dry, level surface such

as a counter or table top.

2 Align and lower the bowl onto the motor base. (Fig. 1)

Handle should be aligned slightly to the right of the “LOCK” symbol on the motor base.

3 Rotate the bowl clockwise as far as it will go to lock in

place. (Fig. 2)

4 The bowl can be placed on the motor base two ways;

the handle can be on the front right corner or the front left corner. (Fig. 3a, Fig. 3b)

5 Holding the desired blade by the top of the shaft, place

it onto the drive gear inside the bowl. Ensure that the blade assembly is seated properly and is standing upright. (Fig. 4)

NOTE: The blade will ﬁt loosely on the drive gear.

Fig. 3a

Fig. 3b

6 Add the ingredients to the bowl, making sure that they

do not exceed the highest measured marking line on the side of the bowl.

7 Holding the lid from the feed chute, place it on top of

the bowl and turn clockwise aligning the arrow ( located on the lid with the arrow ( ) located on the bowl’s handle. You will hear a click when the lid is locked in place. (Fig. 5)

8 Plug the power cord into the electrical outlet and press

the power button (

NOTE: As a safety feature, the power button (

will ﬂash and the motor will not work if the bowl and lid are not installed correctly. When the bowl and lid are installed properly, the power button ( ) will be solid, indicating that the appliance is ready for use.

NOTE: The 64 oz. bowl is not intended for

blending drinks. Do not overﬁll. To add liquids during processing, remove the food pusher from the feed chute to drizzle in liquids. Do not remove the lid while in use.

Fig. 4

Fig. 5

)

www.ninjakitchen.com

Assembly and Use for the 64 oz. Bowl - cont.

USE

Fig. 1

REMOVAL

USING THE CHOPPING BLADE ASSEMBLY

1 Holding the chopping blade assembly by the shaft,

place it onto the gear shaft inside the bowl. Ensure that the blade assembly ﬁts around the gear shaft and that it is standing straight.

2 Add the ingredients and secure the bowl lid onto the

bowl. (Fig. 1)

3 Plug the power cord into the electrical outlet and press

the power button (

4 Select the speed that best suits your needs. Pulse

ingredients for even chopping by pressing down in short intervals.

NOTE: Please refer to “Speed Settings & Uses” chart

for suggested uses and speeds.

5 When you have reached your desired consistency, stop

the appliance by pressing the power button ( wait for the blade assembly to stop turning.

6 To remove the lid, press the release button and turn the

lid counterclockwise and lift the lid off. Turn the bowl counterclockwise and then lift off the base.

(Fig. 2, Fig. 3)

CAUTION: Blades are not locked in place. If

pouring from the bowl, ALWAYS remove the blade assembly ﬁrst before pouring.

) and

USE

Fig. 2

Fig. 4

Fig. 3

USING THE DOUGH BLADE

WARNING: Never leave the appliance unattended while

inuse.

IMPOR TA NT: Push down lightly on the base to ensure the

suction feet are adhered to the surface.

1 Holding the dough blade by the shaft, place it onto the

gear shaft inside the bowl. Ensure that the blade assembly ﬁts around the gear shaft and that it is standing straight.

(Fig. 4)

2 Add the ingredients and secure the bowl lid onto the bowl. 3 Plug the power cord into the electrical outlet and press on

the power button ( ). Select Speed 1 on the control panel and process until ingredients come together to form a mass.

NOTE: Please refer to “Speed Settings & Uses” chart for

suggested uses and speeds.

4 Once ﬁnished making dough, stop the appliance by

pressing the power button ( ) and wait for the blade assembly to stop turning.

5 To remove the lid, press the release button and turn the lid

counterclockwise. (Fig. 2)

6 Turn the bowl counterclockwise and lift it to remove it from

the motor base. (Fig. 3)

7 To release the motor base from the counter or table top,

lift the base up from underneath the sides of the unit. Release paddles on both sides will help to disengage the suction feet from the surface.

NOTE: The suction feet provide added stability.

TOLL FREE: 1-877-646-5288

Assembly and Use for the Disc Attachments

Use caution when handling the discs as the blades are very sharp.

The feed chute lid features a two part pusher to guide food through

NOTE:

the chute. Use the full pusher for larger items such as cucumbers. Twist and pull to remove the smaller pusher and use the narrow chute for smaller items such as carrots.

USING THE DISCS

IMPORTANT: Only use Speed 1 when using either

disc attachment.

NOTE: The Slicing/Shredding Disc is reversible. Use the

side labeled “Slicer” for Slicing. Carefully ﬂip the disc over to the side labeled “Shredder” for shredding.

1 Place the motor base on a clean, dry, level surface such

as a counter or table top. (Fig. 5)

2 Secure the bowl onto the motor base. 3 Place the spindle inside the bowl. 4 Use the ﬁnger holes to grasp the selected disc and place it

over the spindle.

5 Place the feed chute lid on the bowl and turn clockwise

until you here a click indicating the lid is locked in place.

(Fig. 5)

6 Plug the power cord into the electrical outlet and press the

power button (

7 Select Speed 1 on the control panel. The discs will

begin spinning.

8 Add the food that you want to slice, shred or grate through

the feed chute on the lid. (Fig. 5) Use the two-part food pusher to help guide the food through the feed chute. The middle piece of the food pusher is removable to use for smaller ingredients.

9 When ﬁnished, stop the appliance by pressing the power

button ( button on the feed chute lid located near the handle to unlock and turn the lid counterclockwise. Lift to remove

Fig. 5

from the processor bowl. Using the ﬁnger holes, carefully lift the disc out of the bowl and remove the spindle.

) to turn the unit “On”.

) and wait for the disc to stop turning. Press the

www.ninjakitchen.com

Speed Setting & Uses

FUNCTION CONTAINER BLADE ASSEMBLY

Nutrient & Vitamin

Extraction

Mincing Nutri Ninja

Nutri Ninja® Cup Nutri Ninja® Blade Nutri Ninja

Cup Nutri Ninja® Blade Nutri Ninja

SPEED

BUTTON

TYPE OF FOOD

Fruits

Vegetables

Onion Garlic Herbs

Bread dough

Kneading Bowl Dough Blade 1

Pizza dough

Pretzel dough

Dough Mixing Bowl Dough Blade 1 Cookie dough

Pâtés

Stewed fruits

Processing

Bowl

Nutri Ninja

Cup

Chopping Blade

Nutri Ninja® Blade

Pulse

Nutri Ninja

Dips

Apple sauce

Spreads

Soups

Baby food

Salad Dressings

Emulsifying Bowl Chopping Blade 2

Dips

Sauces

Grinding Bowl Chopping Blade 2 Meat

Grating Bowl Grating Disc 1

Chopping

Bowl

Nutri Ninja

Cup

Chopping Blade

Nutri Ninja® Blade

Nutri Ninja®

Mixing Bowl Dough Blade 1

Pulse

Grated cheese Bread crumbs

Salsa

Vegetables

Nuts

Light cake mixes

Batters

Ice Crushing Pitcher Stacked Blade Assembly 3 Ice

Pureeing

Pitcher

Nutri Ninja

Stacked Blade Assembly

Cup

Nutri Ninja® Blade

Nutri Ninja

Smoothies

Smooth soups

Milkshakes

Slicing/Shredding Bowl Slicing/Shredding Disc 1

TOLL FREE: 1-877-646-5288

Vegetables

Cheese

Care & Maintenance

HOW TO CLEAN

CAUTION: Make sure that the motor base is unplugged

from the power source before inserting or removing any blade assembly and before cleaning.

CAUTION: DO NOT immerse the motor base into water

or any other liquid.

NOTE: All jars, lids, discs and blades are dishwasher

safe. All jars, lids and plastic components of blade and disc assemblies are BPA free.

1 Separate/remove all parts from each other.

2 Clean the motor base with a damp cloth and wipe dry.

3 Place the pitcher, Nutri Ninja

dishwasher. Place the lids and blade assemblies on the top rack. Use caution when handling the blade

assemblies as the blades are very sharp.

NOTE: You may also wash the containers by ﬁlling ¾

of the container with warm water and a drop of dish washing detergent, placing the corresponding lid on the container and pressing the pulse button a few times. Once clean, remove the container from the motor base. Rinse the container, blade assembly and lid under running water. Allow all the parts to dry before storing.

Please call customer service if any servicing needs to

be performed on the appliance at 1-877-646-5288.

cup and bowl in the

HOW TO STORE

1 Store the Ninja® Mega Kitchen System® upright

with the pitcher on the motor base, Stacked Blade Assembly inside the pitcher and the lid locked on the pitcher. Do not place anything on top. Store

the bowl with the Chopping Blade assembly inside and the lid on top. Store the Nutri Ninja® cup with the blade assembly attached to the cup and all other attachments along side the appliance or in a cabinet where they will not be damaged and won’t cause a hazard.

RESETTING THE MOTOR THERMOSTAT

The Ninja® Mega Kitchen System® features a unique safety system which prevents damage to the unit’s motor and drive system should you inadvertently overload your appliance. If the appliance is being overloaded, the motor will stop and the power light will remain lit and speeds 1, 2 and 3 will ﬂash. To reset the appliance, follow the resetting procedure below:

1 Unplug the appliance from the electrical outlet.

2 Remove and empty the container and ensure that no

food is jamming the blade assembly.

3 Allow the appliance to cool for approximately 15

minutes.

4 Re-install the container onto the base and re-plug the

appliance into the electrical outlet.

5 Proceed to use the appliance as before making sure not

to exceed the recommended maximum capacities.

www.ninjakitchen.com

Troubleshooting Guide

PROBLEMS POSSIBLE REASONS & SOLUTIONS

Motor doesn’t start or attachment doesn’t rotate.

Make sure the container is securely placed on motor base.

Make sure the lid is securely on container in the correct position (align arrows).

The appliance is turned “Off”. Press the power button (

Check that the plug is securely inserted into the electrical outlet.

Check the fuse or circuit breaker.

The unit has overloaded. The appliance will stop and the power light will remain on while speeds 1, 2 and 3 will ﬂash. Unplug and wait approximately 15 minutes before using again.

The unit has overheated. Unplug and wait approximately 15 minutes before using again.

) to turn “On”.

Food is unevenly chopped.

Food is chopped too ﬁne or is too watery.

Food collects on lid or on the sides of the container.

You cannot achieve snow from solid ice.

Motor base won’t stick to counter or table top.

Leaking is occurring when using the Nutri Ninja® cup.

Ingredients are stuck and not fully blending.

The Nutri Ninja® button does not work.

Either you are chopping too much food at one time, or the pieces are not of an even size. Try processing smaller amounts per batch.

The food has been over processed. Use pulse button for controlled processing.

The mixture is to thick. Add more liquid.

Do not use ice that has been sitting out or has started to melt. Use ice straight from the freezer.

Make sure surface and suction feet are wiped clean. Suction feet will only stick to smooth surfaces. Suction feet WILL NOT stick on some surfaces such as, wood, tile and non-polished ﬁnishes.

DO NOT attempt to use appliance when the motor base is stuck to a surface that is not secure, (cutting board, platter, plates, etc.).

Ensure the blade is properly twisted into the cup and sealed tightly into place. Check to see that the lid gasket is properly in place.

You may have overloaded the Nutri Ninja® cup. Try pulsing 3-5 times and then resume blending. You may also add liquid to make blending easier.

The Nutri Ninja® button will only operate when you have the Nutri Ninja® cup assembled to the motor base. This function was designed speciﬁcally for the Nutri Ninja Cups to operate at the ideal speed.

Replacement Parts

ORDERING REPLACEMENT PARTS

To order additional parts and attachments, please visit our website: www.ninjakitchen.com or feel free to contact customer service: 1-877-646-5288.

TOLL FREE: 1-877-646-5288

ONE (1) YEAR LIMITED WARRANTY

EURO-PRO Operating LLC warrants this product to be free from material defects and workmanship for a

period of one (1) year from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.

The liability of EURO-PRO Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by EURO-PRO Operating LLC.

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer support, please call our customer care and product specialists at , call 1-877-646-5288 or visit our website www.ninjakitchen.com.

If the appliance is found to be defective in material or workmanship, EURO-PRO Operating LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *

This Limited Warranty is extended to the original purchaser of the unit and excludes all other legal, implied and/ or conventional warranties. The responsibility of EURO-PRO Operating LLC if any, is limited to the speciﬁc obligations expressly assumed by it under the terms of this Limited Warranty. In no event is EURO-PRO Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

This Limited Warranty gives you speciﬁc legal rights, and you may also have other rights which vary from state to state or from province to province.

*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.

PRODUCT REGISTRATION

Please visit www.ninjakitchen.com or call 1-877-646-5288 to register your new Ninja® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address.

The registration will enable us to contact you in the unlikely event of a product safety notiﬁcation. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.

www.ninjakitchen.com

Euro-Pro Operating LLC US: Newton, MA 02459 CAN: Ville St-Laurent, QC H4S 1A7

1-877-646-5288 www.ninjakitchen.com

Euro-Pro, Mega Kitchen System, Nutri Ninja, and Ninja are trademarks of Euro-Pro Operating LLC.

Illustrations may differ from actual product. We are constantly striving to improve our products, therefore the speciﬁcations contained herein are subject to change without notice.

Sharp BL773CO User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual