SHARP ARSP5, ARD16, ARPG2, AL-12PKM Service Manual
AR-SP5
AR-D16
SERVICE MANUAL
CODE : 00ZARSP5//A1E
DIGITAL COPIER OPTIONS
AR-PG2 AL-12PKM
[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1
[ 2 ] UNPACKING AND INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . 2 - 1
[ 3 ] AR-SP5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 - 1
[ 4 ] AR-D16 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 - 1
MODEL
CONTENTS
AR-SP5
AR-D16
AR-PG2
(SPF)
(1 TRAY UNIT)
(GDI/Scanner Kit)
AL-12PKM
(GDI/Scanner Kit)
[ 5 ] AR-PG2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 - 1
● PARTS GUIDE
Parts marked with “ ” are important for maintaining the safety of the set. Be sure to replace these parts with
specified ones for maintaining the safety and performance of the set.
This document has been published to be used
SHARP CORPORATION
for after sales service only.
The contents are subject to change without notice.
[1] GENERAL
1. List of available options
Model
AR-122E AR-152E AR-153E AR-157E
Option
AR-SP5
(SPF)
AR-D16
(1 TRAY UNIT)
AR-PG2
(GDI/Scanner Kit)
AL-12PKM
(GDI/Scanner Kit)
: Option available
: Option not available
B. AR-D16 (250 - Sheet Paper Feed Unit)
The paper feed unit provides the convenience of increased paper
capacity for the copier and a greater choice of paper sizes readily
available for copying.
Part names
Side cover
Tray
2. Outline and specifications of each option
A. AR-SP5 (Single Pass Feeder)
The single pass feeder (SPF) holds up to 30 originals for automatic
feeding.
Part names
Original guides
Document feeder tray
Specifications
Acceptable
originals
Power supply Drawn from the copier
Weight Approx. 6.6 lbs. (3kg)
Dimensions 19.6" (W)
Weight: 14 to 23.9 lbs.
Size: 5-1/2"
Capacity: Up to 30 sheets
(498 mm (W)
× 8-1/2" to 8-1/2" × 14"
× 15" (D) × 4.3" (H)
× 380 mm (D) × 110 mm (H))
Feeding roller cover
SPF exit area
Specifications
Copy paper size 5-1/2" × 8-1/2" to 8-1/2" × 14"
Paper weight 15 lbs. to 21 lbs.
Paper capacity One paper tray with capacity for 250 sheets of
Weight Approx. 6.6 lbs. (3 kg)
Dimensions 19.6" (W)
Power supply Drawn from the copier
21 lb. bond paper
× 15.6" (D) × 3.5" (H)
(498 mm (W)
× 395 mm (D) × 88 mm (H))
C. AR-PG2, AL-12PKM (GDI/Scanner Expansion Kit)
Printing system Dry, electrostatic transfer
Printing size A6 to A4 (3-1/2"
Print speed Max. 12 pages/min. (Letter or A4)
Continuous printing Max. 99 pages subtractive counter
First-print time
(Approximately)
Resolution Printer 600 dpi
Scanner 600
Emulation SHARP GDI
Page orientation Portrait or landscape
Interface port USB interface (USB1.1 Standard)/
*1: Feed paper lengthwise only.
*2: Data transmission time is not included.
9.6 seconds (Paper: A4) *2
× 1200 dpi
IEEE1284-compliant bi-directional parallel
interface (Only for printer)
× 5-1/2" to 8-1/2" × 14") *1
AR-SP5 GENERAL 1 - 1
[2] UNPACKING AND INSTALLATION
1. AR-SP5 Installation Manual
•
Parts included
• SPF unit
• Hinge guide L • Hinge guide R
• SPF rear cover, 1 pc.
• Screws (M3 × 8), 1 pcs.
3) Remove the hinge guides L and R.
Remove the screws (two for each) and then remove the hinge
guides L and R.
4) Remove the rear cover for the document glass.
<1> Remove the screw and then remove the right glass holder.
<2> Slide the rear cover for the document glass to remove it.
1
2
• Book sensor unit, 1 pc.
Turn the main switch to the “OFF” position and remove the power plug
from the outlet.
1) Remove the document cover.
Remove the document cover from the copier.
2) Remove the rear cabinet.
Remove the four screws and then remove the rear cabinet.
• Installation manual, 1 sheets
5) Attach the book sensor unit.
Insert the actuator of the book sensor unit into the mounting por-
tion in the copier and fix it using the supplied screw (M3
Note: When attaching the sensor unit, fix it using the screw while
pushing the unit upward.
Connect the connector to the connector of the copier and arrange
the wiring as shown in the illustration.
1
Actuator
2
3
× 8).
AR-SP5 UNPACKING AND INSTALLATION 2 - 1
6) Attach the SPF rear cover.
<1> Pass the actuator of the book sensor into the hole of the SPF
rear cover and slide the SPF rear cover to attach it. At this
time, check that the pawl on the back side of the SPF rear
cover is inserted into the copier frame.
<2> Reattach the right glass holder to its original position and fix it
using the screw.
Note: Check that the actuator moves smoothly.
Take care to prevent entry of dirt into the scanner unit.
2
1
7) Attach the hinge guides L and R.
Attach the hinge guides L and R by fitting the pawls (two for each)
into the frame of the copier and secure them with the two screws
for each that have been removed in step 3.
9) Connect the SPF with the copier using the relay harness.
<1> Fit the snap band to the position shown in the illustration.
<2> Connect the connector.
<3> Fit the grounding terminal using the supplied screw (M3
1
3
10) Attach the rear cabinet.
Remove the rib from the rear cabinet.
Note: While pushing down the actuator of the sensor unit, attach
the rear cabinet so that the actuator is inserted into the hole
of the rear cabinet.
<1> Hang the four pawls shown in the illustration below on the
plate.
<2> Push down the actuator of the sensor unit.
<3> Position the cabinet to the upper screw positions.
<4> Ensure that the actuator is inserted into the square hole of
the cabinet.
2
× 8).
Pawls
8) Place the SPF on the copier.
Pawls
Side view
Pawl
M3×8
Pawl
M3×8
M4×12
AR-SP5 UNPACKING AND INSTALLATION 2 - 2
11) Attach the cover to the rear cabinet.
<1> Align the arrow marks as shown in the illustration.
<2> Then slide the cover to the left.
<3> Secure the cover with a screw.
17) Check the copy ratio, and then check the center displacement and
leading edge image void.
Place an original on the document glass and make a copy.
Then, place an original in the document feeder tray and make a
copy.
If the center of the copy from the document glass is displaced from
the copy from the document feeder, adjust the center referring to
the service manual.
2. AR-D16 Installation Manual
•
Parts included
12) Attach the SPF to the copier.
Attach the SPF by inserting the hinge guide sections of the SP5
into the hinge guides L and R.
1
2
2
13) Insert the power plug into the outlet and turn the main switch of the
copier to the “ON” position.
14) Perform SIM setting.
Execute simulation [2] of [26] and enter [1].
15) Check the ON/OFF operation of the open detection sensor.
Execute simulation [2] of [2] and check that the indicator on the
operation panel lights up and goes out by opening and closing the
SPF.
• Screws (M4 × 16), 4 pcs.
Turn the main switch to the “OFF” position and remove the power plug
from the outlet.
1) Remove the DV cartridge and the drum cartridge from the copier.
Open the tray, the side door, and the front cabinet, and then
remove the DV cartridge and the drum cartridge.
Note: Be sure to carry out the operation in the order of (1), (2), (3),
and (4).
1
4
3
2
2) Make the copier upright.
Close the front cover, side cover, and bypass tray, and then make
the copier upright in the orientation shown in the illustration.
16) Carry out automatic adjustment of SPF scanning position.
Execute simulation 53-08 to carry out automatic adjustment of
SPF scanning position.
For details, see the service manual.
AR-SP5 UNPACKING AND INSTALLATION 2 - 3
3) Remove the OP gear cover and rubber feet from the bottom of the
copier.
Remove the screw and remove the OP gear cover.
Then, take off and remove the rubber feet.
Rubber foot
OP gear cover
Rubber foot
5) Remove the rear cover and connect the connector.
Remove the screw and remove the rear cover.
Then, connect the connector of the second cassette unit to that of
the copier.
6) Attach the rear cover.
Attach the rear cover to its original position and secure it with the
screw (M4
× 12).
4) Install the second cassette unit to the copier.
If the second cassette unit is aligned to the copier, it can be posi-
tioned automatically.
Hold the copier lightly to prevent it from toppling down and secure
the second cassette unit with four screws (M4
× 16).
7) Return the copier to the normal orientation.
When returning the copier to the normal orientation, gently return it
without giving a shock.
AR-SP5 UNPACKING AND INSTALLATION 2 - 4
8) Insert the drum cartridge and the DV cartridge into the copier.
Open the tray, the side door, and the front cabinet, insert the drum
cartridge and the DV cartridge, and then close the front cabinet,
the side door, and the tray.
Note: Be sure to carry out the operation in the order of (1), (2), (3),
and (4).
11) Load paper into the paper tray.
When loading paper, do not exceed the maximum height line.
3
1
2
9) Remove the paper tray lock for packing.
Remove the paper tray lock for packing that secures the turning
plate in the paper tray by rotating it in the direction of the arrow and
store it in the specified position.
10) Set the paper tray side guide.
Squeeze the lever of the paper tray side guide to slide the guide to
the position for the paper size to be used.
4
12) Insert the power plug into the outlet and turn the main switch to the
“ON” position. Then, perform the following procedure.
13) Perform SIM setting.
Execute simulation [3] of [26] and enter [1].
14) Check the center displacement.
Place an original on the document glass and make a copy using
the tray in the copier.
Then, make a copy using the tray in the installed optional paper
feed unit.
If the center of the copy from the optional paper feed unit is dis-
placed from the copy from the tray in the copier, adjust the center
referring to the service manual.
3. AR-PG2/AL-12PKM
A. Installation Manual
• Parts included
• Printer board ... 1
(AR-PG2)
• Screws ... 5
• Software CD-ROM ... 1
AR-SP5 UNPACKING AND INSTALLATION 2 - 5
• Printer board ... 1
(AL-12PKM)
• Core ... 1
• Cable ... 1
(AL-12PKM only)
• Screwdriver ... 1
(AL-12PKM only)
• Installation manual ... 1
Turn the main switch to the “OFF” position and remove the power plug
from the outlet.
1) Removing the cabinet cover.
<1> Ensure that the power switch on the unit is in the off position.
Remove the power cord from the power cord socket at the
rear of the unit.
<2> Remove the screw from the cabinet cover at the rear side of
the unit using the supplied screwdriver.
<3> Slide the cabinet cover in the direction indicated by the arrow
and pull the cover while raising it a little to remove it.
<4> Secure the printer board using the supplied five screws.
<5> Insert the cable into the printer board connector, with the side
with the blue parts facing right.
(AL-12PKM)
Printer board
connector
Blue parts
<6> Insert the core through to the middle position of the cable.
(AL-12PKM)
2) Installing the printer board.
<1> Remove the printer board from the protective bag.
<2> Insert the core as shown in the illustration.
<3> Install the printer board so that the parallel interface connec-
tor of the board is fitted into the hole for the connector.
(AR-PG2)
Hole for the
connector
Core
(AL-12PKM)
Hole for the
connector
<7> Connect the board cable to the connector of the unit.
3) Replace the cabinet cover.
<1> Bend the end of the cabinet cover at the slit and break it off.
Caution: Take care in handling the cabinet cover because the
exposed edge could be sharp and may injure your
hands.
<2> Secure the cabinet cover using the screw which has been
removed.
AR-SP5 UNPACKING AND INSTALLATION 2 - 6
B. Installing the software
The following term is used in this section.
MFP
Means the unit as a printer and scanner.
• For this description, it is assumed that the mouse is configured for
right hand operation.
• To print or scan, the MFP must be in the online state.
• The scanner feature only works when using a USB interface cable.
• If any error message appears, solve the problem following the
instructions on the screen. After your problem is solved, the installing
procedure will be continued. Depending on your problem, you may
have to exit the installer. In this case, click the "Cancel" button to exit
the installer. After solving your problem, reinstall the software from
the beginning.
(1) Windows XP (USB/parallel interface)
Before starting the installation, make sure the USB or parallel interface
cable is not connected to the MFP.
1) Insert the supplied CD-ROM into your CD-ROM drive.
2) Click the "start" button, click "My Computer", and then double-click
the CD-ROM icon.
• When any of "Found New Hardware Wizard" messages appear
during the software installation, be sure to click the "Cancel" button.
3) Double-click the "Setup" icon.
If the language selection screen appears after you double click the
"Setup" icon, select the language you wish to use and click the
"Next" button. (Normally, the correct language is selected automatically.)
4) Select the software packages to be installed, and then click the
"Next" button.
The software packages with checkmark on the list on the screen
will be installed.
Click the "Display README" button to show the information on the
selected package.
5) Review the software packages to be installed on the screen, and
then click the "Start" button.
The software packages to be installed will be displayed on the
screen. If inappropriate packages are displayed, click the "Back"
button to select appropriate packages again.
6) Copying files for MFP driver installation and parallel interface setup
(This step will start if it was selected in step 4).
1. After confirming the message in the "Welcome" window, click
the "Next" button.
2. A dialog box appears asking you to verify that the USB or par-
allel interface cable is not connected to the MFP. Make sure
that the interface cable is not connected and click the "Next"
button.
3. Click the "Next" button in the dialog box to install the MFP
driver or Cancel to quit the installation.
The setup program will start to copy the files.
If the following screen appears while the files are being copied
(the message may appear more than once), click "Continue
Anyway".
• If you are using the parallel interface connection, do not select
the Button Manager checkbox because this feature is not supported with the parallel interface.
• If the following screen appears, click the "OK" button. Review
the contents in "BEFORE INSTALLATION", and then select only
appropriate the software packages to be installed.
4. When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
The Button Manager installer will start.
7) Begin installation of the Button Manager (This step will start if it
was selected in step 4).
1. After confirming the message in the "Welcome" window, click
the "Next" button.
2. Read the message in the "Please read the following informa-
tion." window, and then click the "Next" button.
3. When a message appears that lets you specify the location for
the software to be installed, click the "Next" button.
4. If the program displays, "Do you want the Button Manager
added to Windows Startup?", check "Yes" and click the "OK"
button.
The setup program will start to copy the files.
5. Click the "Finish" button when the message informs you that
setup is successful.
The Sharpdesk installer will start.
8) Begin installation of the Sharpdesk (This step will start if it was
selected in step 4).
1. After confirming the message in the "Welcome to Sharpdesk
installation" window, click the "Next" button.
2. Read the message in the "Information" window, and then click
the "Next" button.
3. When the "Choose Destination Location" window appears,
click the "Next" button.
AR-SP5 UNPACKING AND INSTALLATION 2 - 7
4. When the "Select Program Folder" window appears, click the
"Next" button.
The setup program will start to copy the files.
If the dialog box asking "If you have TIFF files saved using
Photo-Shop or Imaging for Windows you should hit Skip"
appears. Answer the question to continue the Sharpdesk
installation.
5. Click the "Finish" button when the message informs you that
Setup is complete.
9) Click the "Close" button when the message informs you that
"Setup has finished". When the "Now connect the MFP interface
cable to the PC" dialog box appears, click the "OK" button.
• After the installation, a message to restart your computer may be
displayed. In this case, click the "Yes" button to restart your computer.
• For parallel interface connection ensure that your computer and
MFP are turned off before connecting the cable.
(2) Windows 98/Me/2000 (USB interface)
Before starting the installation, make sure the USB interface cable is
not connected to the MFP.
1) Insert the supplied CD-ROM into your CD-ROM drive.
2) Double-click "My Computer", and then double-click the CD-ROM
icon.
• When any of "Hardware Found", or "Found New Hardware Wiz-
ard" messages appear during the software installation, be sure
to click the "Cancel" button.
3) Double-click the "Setup" icon.
• If the language selection screen appears after you double click
the "Setup" icon, select the language you wish to use and click
the "Next" button. (Normally, the correct language is selected
automatically.)
4) Select the software packages to be installed, and then click the
"Next" button.
The software packages with checkmark on the list on the screen
will be installed. Click the "Display README" button to show the
information on the selected package.
10) Connect the USB interface cable or parallel interface cable (see
page 5-8).
Windows will detect the MFP and the Plug and Play screen will
appear. If you are using Windows XP with the parallel interface, go
to step 12.
11) Begin installation of the scanner driver.
1. "SHARP AL-xxxx" (where xxxx is the model name of your
MFP) will appear in the "Found New Hardware Wizard" dialog
box. Select "Install the software automatically (Recommended)" and click the "Next" button.
2. The "Install hardware" dialog box will appear. Click the "Con-
tinue Anyway" button.
3. When installation of the driver is completed, click the "Finish"
button to finish the scanner driver installation.
12) Begin installation of the printer driver.
1. "SHARP AL-xxxx" (where xxxx is the model name of your
MFP) will appear in the "Found New Hardware Wizard" dialog
box. Select "Install the software automatically (Recommended)" and click the "Next" button.
2. The "Hardware Installation" dialog box will appear. Click the
"Continue Anyway" button.
3. When installation of the driver is completed, click the "Finish"
button to finish the printer driver installation.
You have completed the installation of all the software.
• If the following screen appears, click the "OK" button. Review
the contents in "BEFORE INSTALLATION", and then select the
appropriate driver software packages to be installed.
5) Review the software packages to be installed on the screen, and
then click the "Start" button.
The software packages to be installed will be displayed on the
screen. If inappropriate packages are displayed, click the "Back"
button to select appropriate packages again.
6) Copying files for MFP driver installation.
1. After confirming the message in the "Welcome" window, click
the "Next" button.
2. A dialog box appears asking you to verify that the interface
cable is not connected to the MFP. Make sure that the interface cable is not connected and click the "Next" button.
3. Click the "Next" button in the dialog box showing the files to be
copied for installation of the MFP driver.
The setup program will start to copy the files.
In Windows 2000, if the following screen appears while the
files are being copied (the message may appear more than
once), click "Yes" in Windows 2000.
AR-SP5 UNPACKING AND INSTALLATION 2 - 8
4. The following screen appears when all of the files for the USB
interface connection have been copied. If you are not using a
parallel interface cable for connection to the MFP, please click
the "No" button.
5. When the "The MFP driver installation is complete." dialog box
appears, click the "OK" button.
The Button Manager installer will start.
7) Begin installation of the Button Manager (This step will start if it
was selected in step 4).
1. After confirming the message in the "Welcome" window, click
the "Next" button.
2. Read the message in the "Please read the following informa-
tion." window, and then click the "Next" button.
3. When a message appears that lets you specify the location for
the software to be installed, click the "Next" button.
4. If the program displays, "Do you want to add Button Manager
to Startup program?", check "Yes" and click the "OK" button.
The setup program will start to copy the files.
5. Click the "Finish" button when the message to inform you of
the completion of the installation appears.
The Sharpdesk installer will start.
8) Begin installation of the Sharpdesk (This step will start if it was
selected in step 4).
1. After confirming the message in the "Welcome to Sharpdesk
installation" window, click the "Next" button.
2. Read the message in the "Information" window, and then
click the "Next" button.
3. When the "Choose Destination Location" window appears,
click the "Next" button.
4. When the "Select Program Folder" window appears, click the
"Next" button.
The setup program will start to copy the files.
If the dialog box asking "If you have TIFF files saved using
Photo-Shop or Imaging for Windows you should hit Skip"
appears. Answer the question to continue the Sharpdesk
installation.
9) Click the "Close" button when the message to inform you of the
completion of the installation appears. When the "Now connect the
MFP interface cable to the PC. This will finalize the drivers installation and settings." dialog box appears, click the "OK" button.
• After the installation, a message to restart your computer may be
displayed. In this case, click the "Yes" button to restart your computer.
10) Connect the USB interface cable (see page 5-8).
Windows will detect the MFP and the Plug and Play screen will
appear.
11) Follow the instructions in the Plug and Play screen that appears in
your version of Windows to begin the installation.
You have completed the installation of the software.
(3) Windows 95/98/Me/NT4.0/2000 (Parallel interface)
Before starting the installation, make sure the USB or parallel interface
cable is not connected to the MFP.
1) Insert the supplied CD-ROM into your CD-ROM drive.
2) Double-click "My Computer", and then double-click the CD-ROM
icon.
• When any of "Hardware Found", or "Found New Hardware Wiz-
ard" messages appear during the software installation, be sure
to click the "Cancel" button.
3) Double-click the "Setup" icon.
• If the language selection screen appears after you double click
the "Setup" icon, select the language you wish to use and click
the "Next" button. (Normally, the correct language is selected
automatically.)
4) Select the software packages to be installed, and then click the
"Next" button.
The software packages with checkmark on the list on the screen
will be installed.
Click the "Display README" button to show the information on the
selected package.
5. Click the "Finish" button when the message to inform you of
the completion of the installation appears.
AR-SP5 UNPACKING AND INSTALLATION 2 - 9
• In Windows 95/NT 4.0, "Button Manager" does not appear. In
Windows 98/Me/2000, do not select the "Button Manager"
checkbox. because this is not supported when using the parallel
interface.
5) The next screen appears. Make sure that the parallel interface
cable is not connected, and click "OK".
Windows 95/NT 4.0 Windows 98/Me/2000
Loading...