SHARP AR-M207E, AR-M162E Service Manual

AR-M162E

CODE : 00ZARM207EA1E

DIGITAL COPIER

AR-M207E

With the RSPF installed

[ 1 ] GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 - 1

[ 2 ] SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 - 1

[ 3 ] CONSUMABLE PARTS . . . . . . . . . . . . . . . . . . . Refer to AR-M207

[ 4 ] EXTERNAL VIEWS AND INTERNAL STRUCTURES . . Refer to AR-M207

[ 5 ] UNPACKING AND INSTALLATION . . . . . . . . . . Refer to AR-M207

[ 6 ] ADJUSTMENTS . . . . . . . . . . . . . . . . . . . . . . . . . Refer to AR-M207

[ 7 ] SIMULATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . Refer to AR-M207

[ 8 ] TROUBLE CODE LIST . . . . . . . . . . . . . . . . . . . . Refer to AR-M207

MODEL

CONTENTS

AR-M162E

[ 9 ] MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . Refer to AR-M207

[10] DISASSEMBLY AND ASSEMBLY . . . . . . . . . . . Refer to AR-M207

[11] KEY OPERATOR PROGRAM . . . . . . . . . . . . . . Refer to AR-M207

[12] FRASH ROM VERSION UP PROCEDURE . . . . Refer to AR-M207

[13] ELECTRICAL SECTION . . . . . . . . . . . . . . . . . . . Refer to AR-M207

Parts marked with “ “ are important for maintaining the safety of the set.

Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.

This document has been published to be used for

SHARP CORPORATION

after sales service only. The contents are subject to change without notice.

[1] GENERAL

1. Cautions on using

A. Warning

• The fusing area is hot. Exercise care in this area when removing misfed paper.

Fusing unit

•Do not look directly at the light source. Doing so may damage your eyes.

2. Installation requirements

Improper installation may damage this product. Please note the following during initial installation and whenever the machine is moved.

1. The machine should be installed near an accessible power outlet for easy connection.

2. Be sure to connect the power cord only to a power outlet that meets the specified voltage and current requirements. Also make certain the outlet is properly grounded.

• For the power supply requirements, see the name plate on the back of

the main unit.

Note: Connect the machine to a power outlet which is not used for other

electric appliances. If a lighting fixture is connected to the same outlet, the light may flicker.

3. Do not install your machine in areas that are:

• damp, humid, or very dusty

• exposed to direct sunlight

• poorly ventilated

• subject to extreme temperature or humidity changes, e.g., near an air

conditioner or heater.

4. Be sure to allow the required space around the machine for servicing and proper ventilation.

8" (20 cm)

B. Cautions

• Do not switch the machine rapidly on and off. After turning the machine off, wait 10 to 15 seconds before turning it back on.

• Place the machine on a firm, level surface.

• When the machine is not used for a long time, for example, during prolonged holidays, turn the power switch off and remove the power cord from the outlet.

• When moving the machine, be sure to turn the power switch off and remove the power cord from the outlet.

• Do not cover the machine with a dust cover, cloth or plastic film while the power is on. Doing so may prevent heat dissipation, damaging the machine.

• Do not make any modifications to this machine. Doing so may result in personal injury or damage to the machine.

• Do not make copies of anything which is prohibited from copying by law. The following items are normally prohibited from printing by national law. Other items may be prohibited by local law.

Money, Stamps, Bonds, Stocks Bank drafts, Checks, Passports, Driver’s licenses

• Do not touch the photoconductive drum. Scratches or smudges on the drum will cause dirty prints.

• Store spare toner cartridges in a cool dry place without removing from the package before use.

• If they are exposed to direct sunlight or excessive heat, poor copies may result.

(20 cm)

AR-M207E M162E GENERAL 1-1

3. Configuration

A. System Configurations

Job separator

(AR-TR4)

RSPF(AR-RP6N) SPF(AR-SP6N)

AR-M207E

With the RSPF installed

Network Box

(AR-NB3)

AR-M162E

2 X 250 sheet paper

feed unit

(AR-D25)

OPTION

MODEL

AR-RP6N REVERSING SINGLE PASS FEEDER OPT NO AR-SP6N SINGLE PASS FEEDER OPT OPT AR-VR5 DOCUMENT COVER OPT STD AR-D24 250-SHEET PAPER FEED UNIT OPT OPT AR-D25 2 x 250-SHEET PAPER FEED UNIT OPT OPT AR-TR4 JOB SEPARATOR TRAY KIT OPT OPT AR-EB9 DUAL FUNCTION BOARD STD STD AR-NB3 NETWORK PRINTING / SCANNING

EXPANSION KIT AR-FX11 FACSIMILE EXPANSION KIT OPT OPT AR-SM5 EXPANSION MEMORY OPT OPT AR-MM9 FAX EXPANSION MEMORY OPT OPT AR-PF1 BARCODE-FONT KIT OPT OPT The AR-NB3 is required AR-PK1N PS3 KIT OPT OPT The AR-NB3 is required AR-PF2 FLASH MEMORY KIT OPT OPT The AR-NB3 is required

AR-M207E AR-M162E Remark

OPT OPT

250 sheet paper

feed unit

(AR-D24)

AR-M207E M162E GENERAL 1-2

[2] SPECIFICATIONS

1. Basic Specification

A. Base Engine

(1) Type

AR-M207E, AR-M162E Desk-top

(2) Engine speed

Paper size AR-M207E AR-M162E

A4/8.5" x 11" 20ppm 16ppm

A4R/8.5" x 11"R 14/15ppm 12ppm

A5/5.5" x 8.5" 20ppm 16ppm

B5/16K 20ppm 16ppm

B5R/16KR 16/15ppm 14ppm

8.5" x 13" 12ppm 11ppm

B4/8.5" x 14 12ppm 10ppm

A3/11" x 17"/8K 11/10/11ppm 9/9/10ppm

(3) Print performance

AR-M207E AR-M162E

GDI Print* 12ppm 12ppm

SPLC Print 20ppm(ROPM) 16ppm(ROPM)

* GDI print measurement conditions: Host PC/CPU = 500 700MHz or

above, Windows 98SE, Data = TestChart-B1.doc, USB1.1, when supporting A4/Letter. Measurement method: With setting to 11, from completion of the first paper exit to completion of the 11th paper exit

(4) Copy speed(cpm)

AR-M207E AR-M162E

Normal

A4/8.5"x11" 20 20 20 16 16 16

A4R/

8.5"x11"R

A5/5.5"x8.5" 20 20 20 16 16 16

B5/16K 20 20 20 16 16 16

B5R/16KR 16/15 16/15 16/15 14 14 14

8.5x13"121212 101010

B4/8.5"x14 12 12 12 10 10 10

A3/11"x17"/8K11/10/1111/10/1111/10/119/9/10 9/9/10 9/9/10

14/15 14/15 14/15 12 12 12

Reduction

Enlargement

Normal

Reduction

Enlargement

(6) Job Speed

AR-M207E AR-M162E

S S 20 Sheets/min(100%) 16 Sheets/min(100%)

S D 9 Sheets/min(45%) -

D D 8 Sheets/min(40%) -

* S S(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document, 5

copies

* S D(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document, 5

copies

* D D(from No. 1 cassette): 10 sheets of A4/8.5" x 11" document(20

surfaces), 5 copies

(7) Continuous copying

Max. number of multi copy

1-999copies(Can be changed to 1-99 in key operator programs)

(8) Engine composition

Photoconductor type

Photoconductor drum dia.

Process cleaning Blade

Copy lamp Cold cathode fluorescent lamp(CCFL)

Developing system

Charging system Saw teeth charging

Transfer system (+)DC scorotron

Separation system (-)DC scorotron

Fusing system Heat roller

Process speed 88mm/s

OPC(Organic Photo Conductor)

30mm

Dry 2-component magnetic brush development

(9) Engine resolution

Resolution Reading: 600 x 300dpi1(600 x 600dpi selectable)

Writing: 600x600dpi

Gradation Reading: 256 gradation, Writing: 2 gradations

(10)Scanner section

Scanner(Document table)

(5) First copy time

First copy time 7.2sec or less

* Measurement conditions: When feeding paper of A4/8.5" x 11" from the

main unit tray, polygon rotation state

Main unit first stage

Main unit second stage

Option paper feed first stage

Option paper feed second stage

Manual tray 7.5sec or less

First copy time from the document feed unit

SPF 12sec or less

RSPF 12sec or less

7.2sec or less

8.5sec or less

9.5sec or less

10.5sec or less

AR-M207E M162E SPECIFICATIONS 2-1

+ 9 hidden pages