|
Date : |
Aug. 22, 1997 |
DIGITAL COPIER : AR-5132 |
No. : |
ARE-049 |
|
|
[Service Information] |
|
|
|
|
|
|
|
CHANGEINAUDINTERFACEHARNESSWIRING. |
|
|
|
|
|
1.Model Name: |
AR-5132 |
||
2.General: |
Because the 2P connector harness for the AUD interface harness counter in the control |
||
|
panel unit is too long, it may get caught when the cabinet is being put on during repair. |
||
|
Therefore the changes below have been made to the wiring method. |
||
|
|
LCD control PWB |
|
|
|
AUD interface harness |
|
|
White |
|
||
|
|
DHAI-2530FCZZ |
||
|
Wire so it catches
Red
on the boss.
Door SW
OP PWB
Panel side
To OPC PWB
Fastening band
As shown in the diagram above, bend connector C away from fastening band "a", and fasten the harness for connectors B & C 40mm from fastening band a with "a" fastening band.
3.Action: From the 1st lot of 1997 July production.
1/2
|
|
Green |
SHARP CORPORATION |
Reprography Division |
C |
|
Ref. |
Model |
|
|
|
|
Current parts |
|
New parts |
|
|
Effec- |
Inter- |
|
|
|
|
|
|
|
|
|
|
|
|
|
||||
Version |
|
P/G No. |
|
|
|
|
|
Parts name |
tive |
change- |
Note |
|||
No. |
name |
|
|
|
|
|
Price |
|||||||
|
|
|
|
Parts code |
|
Parts code |
|
time |
ability |
|
||||
|
|
|
|
|
|
|
rank |
|
|
|||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
LBNDJ0013FCZZ |
|
Q’ty change: |
|
|
1st lot |
|
|
|
|
AR-5132 |
All |
|
2 |
|
|
AA |
Fastening band |
---- |
|
||||
|
|
|
(Q’ty: 2) |
|
2 → 3 |
|
’97/7 |
|
||||||
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
<Interchange> |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
1. Interchangeable. |
|
|
|
|
|
|
4. Not interchangeable. |
|
|
|
|||
|
|
|
|
|
|
|||||||||
|
2. Current type can be used in place of new type. |
|
5. Interchangeable if replaced with same types of |
|||||||||||
|
New type cannot be used in place of current type. |
|
related parts in use. |
|
|
|
3. Current type cannot be used in place of new type.
6. Others.
New type can be used in place of current type.
Parts marked with ‘‘ ’’ is important for maintaining the safety of the set. Be sure to replace these parts with specified ones for maintaining the safety and performance of the set.
2/2