Sharp AN-PH80LP Installation Manual

LAMP UNIT (LAMP/CAGE MODULE)

2

3

5

6

FOR PROJECTOR

MODEL

AN-PH80LP

INSTALLATION MANUAL

CAUTION:

• Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or
Service Center* replace lamp if rupture occurs.

• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait
at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool
before removing the lamp unit.

It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi -

■

cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of
this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized
Projector Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or
Service Center*, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP

* Confi rm the name of the Dealer or Service Center referring to your projector operation manual.

Removing and Installing the
Lamp Unit

Warning!

Do not remove the lamp unit from the projector right

•

after use. The lamp and parts around the lamp will
be very hot and may cause burns or injury.

STANDBY/ON button

U.S.A. ONLY

Remove the lamp unit.

4

•

Loosen the securing screws (two for each lamp)
from the lamp unit. Hold the lamp unit by the
handle and pull it in the direction of the arrow. At
this time, keep the lamp unit horizontal and do not
tilt it.

Insert the new lamp unit.

5

•

Press the lamp unit fi rmly into the lamp unit
compartment. Fasten the securing screw.

Replace the lamp unit cover.

6

•

Align the lamp unit cover and slide it to close (1).
Then tighten the user service screw (2) to secure
the lamp unit cover.

Info

If the lamp unit and lamp unit cover are not

•
correctly installed, the power will not turn on,
even if the power cord is connected to the
projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

Make sure to reset the lamp timer only when

•
replacing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.
You can reset the lamp timer only when “STANDBY

•
mode” is set to “Standard”.

Info

•

Do not touch the glass surface of the lamp unit or
the inside of the projector.

•

To avoid injury to yourself and damage to the lamp,
make sure you carefully follow the steps below.

•

Do not loosen other screws except for the lamp unit
cover and lamp unit.

Press STANDBY/ON on the projector

1

or on the remote control to put the
projector into Standby mode.

Switch the MAIN POWER switch on

2

the projector to “OFF” and then
disconnect the power cord.

•

Unplug the power cord from the AC socket.

•

Leave the lamp until it has fully cooled down
(about 1 hour).

Remove the lamp unit cover.

3

•

Loosen the user service screw (1) that secures the
lamp unit cover. Remove the lamp unit cover (2).

MAIN POWER switch

AC socket

User service screw
(for lamp unit cover)

Connect the power cord and switch

1

1

the MAIN POWER switch on the
projector to “ON”.

•

Plug the power cord into the AC socket of the
projector.

Reset the lamp timer.

2

•

The projector enters Standby mode when you
reset the lamp timer.

For Lamp 1

•

When you reset the timer, press MENU → ENTER
→ ENTER → MENU → O → STANDBY/ON on
the projector.

•

“LAMP1 0000H” is displayed, indicating that the
lamp timer is reset.

For Lamp 2

•

When you reset the timer, press MENU → ENTER
→ ENTER → MENU → Q → STANDBY/ON on
the projector.

•

“LAMP2 0000H” is displayed, indicating that the
lamp timer is reset.

AC socket

MENU button

O/Q buttons

ENTER button

STANDBY/ON
button

Printed in China
9NK5012072400
11P05-CH-NM

DEUTSCH

FRANÇAIS

ESPAÑOL

ITALIANO

SVENSKA

PORTUGUÊS

Richten Sie sich bitte nach der beim Projektor mitgelieferten
Bedienungsanleitung.
Sie können die Bedienungsanleitung auch von der Website
(http://sharp-world.com/products/index.html) herunterladen.

Reportez-vous au mode d'emploi fourni avec le projecteur.
Vous pouvez également télécharger le mode d'emploi sur le site
Internet (http://sharp-world.com/products/index.html).

Consulte el manual de manejo que se suministra con el proyector.
También puede descargar el manual de manejo del sitio Web
(http://sharp-world.com/products/index.html).

Fare riferimento al manuale d'uso fornito con il proiettore.
È inoltre possibile scaricare lo stesso manuale d'uso dal sito web
(http://sharp-world.com/products/index.html).

NEDERLANDS

Verwijs naar de gebruiksaanwijzing die bij de projector wordt
geleverd.
U kunt de gebruiksaanwijzing ook vanaf internet downloaden
(http://sharp-world.com/products/index.html).

Anlita bruksanvisningen som medföljer projektorn.
Bruksanvisningen kan också nerladdas från vår webbsajt
(http://sharp-world.com/products/index.html).

Consulte o manual de operação fornecido com o projetor.
Pode-se também baixar o manual de operação pela internet
(http://sharp-world.com/products/index.html).