Sharp AN-P610LP Installation Manual

Info

LAMP UNIT (LAMP/CAGE MODULE)

Info

STANDBY button

Power cord

User service screw

Power cord

ENTER button

, ",

| buttons

ON button

AN-P610LP

Compartment

for

Lamp 1

Compartment

for

Lamp 2

User service screw

Securing screws

Handle

FOR PROJECTOR

Model

AN-P610LP

INSTALLATION MANUAL

CAUTION:

•Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or Service Center* replace lamp if rupture occurs.

• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■

It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP

U.S.A. ONLY

3 Remove the lamp unit.

• Loosen the securing screws (two for each lamp) from the lamp unit. Hold the lamp unit by the handle and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

4 Insert the new lamp unit.

• Fully insert the lamp unit into the lamp unit compartment. Press the handles back to their positions, and tighten the securing screws.

5 Replace the lamp unit cover.

• Slide the lamp unit cover to the position where the indicator “|” of the lamp cover unit and the “\” of the projector will meet to close the cover. Then tighten the user service screw to secure the lamp unit cover.

* Confirm the name of the Dealer or Service Center referring to your projector operation manual.

Removing and Installing the Lamp Unit

Warning!

• Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.

• Make sure the lamp unit is removed using the handle. Make sure the glass surface of the lamp unit or the inside of the projector are not touched.

• To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY on the projector or

on the remote control to put the projector into standby mode.

• Disconnect the power cord and unplug the power cord from the AC socket after the cooling fan stops.

• The cooling fan may continue to run for a while even after the power cord is removed.

• Leave the lamp until it has fully cooled down (about 1 hour).

2 Remove the lamp unit cover.

• Loosen the user service screw (1) that secures the lamp unit cover. Remove the lamp unit cover to slide it in the direction of the arrow (2).

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

1 Connect the power cord.

•

Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

For Lamp 1

• When you reset the timer, while simultaneously

holding down \, " and ENTER, press ON on the projector.

• “LAMP1 0000H” is displayed, indicating that the lamp timer is reset.

For Lamp 2

• When you reset the timer, while simultaneously holding down |, " and ENTER, press ON on the projector.

• “LAMP2 0000H” is displayed, indicating that the lamp timer is reset.

Printed in China 9NK5010072000 08P03-CH-NM

DEUTSCH

FRANÇAIS

ESPAÑOL

ITALIANO

NEDERLANDS

SVENSKA

PORTUGUÊS

Richten Sie sich bitte nach der beim Projektor mitgelieferten Bedienungsanleitung. Sie können die Bedienungsanleitung auch von der Website (http://sharp-world.com/products/index.html) herunterladen.

Reportez-vous au mode d’emploi fourni avec le projecteur. Vous pouvez également télécharger le mode d’emploi sur le site Internet (http://sharp-world.com/products/index.html).

Consulte el manual de manejo que se suministra con el proyector. También puede descargar el manual de manejo del sitio Web (http://sharp-world.com/products/index.html).

Fare riferimento al manuale d’uso fornito con il proiettore. È inoltre possibile scaricare lo stesso manuale d’uso dal sito web (http://sharp-world.com/products/index.html).

Verwijs naar de gebruiksaanwijzing die bij de projector wordt geleverd. U kunt de gebruiksaanwijzing ook vanaf internet downloaden (http://sharp-world.com/products/index.html).

Anlita bruksanvisningen som medföljer projektorn. Bruksanvisningen kan också nerladdas från vår webbsajt (http://sharp-world.com/products/index.html).

Consulte o manual de operação fornecido com o projetor. Pode-se também baixar o manual de operação pela internet (http://sharp-world.com/products/index.html).