Sharp AN-F310LP Installation Manual

LAMP UNIT (LAMP/CAGE MODULE)
FOR PROJECTOR

MODEL

AN-F310LP

4 Remove the lamp unit.

• Loosen the securing screws from the lamp unit.
Hold the lamp unit by the handle and pull it in
the direction of the arrow. At this time, keep the
lamp unit horizontal and do not tilt it.

Handle

INSTALLATION MANUAL

CAUTION:

•Potential hazard of glass particles if lamp ruptures. Please have a Sharp Authorized Projector Dealer or
Service Center* replace lamp if rupture occurs.

• Do not remove the lamp unit directly after operation of the projector. The lamp may be extremely hot. Wait at
least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before
removing the lamp unit.

■

It is recommended that the lamp be replaced when the remaining lamp life becomes 5% or less, or when you notice a signifi­cant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this
projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector
Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*,
please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information
www.lamprecycle.org or 1-800-BE-SHARP

* Confirm the name of the Dealer or Service Center referring to your projector operation manual.

U.S.A. ONLY

Removing and Installing the
Lamp Unit

Warning!

• Do not remove the lamp unit from the projector right
after use. The lamp and parts around the lamp will
be very hot and may cause burn or injury.

Info

• Make sure that you remove the lamp unit by the
handle. Do not touch the glass surface of the lamp
unit or the inside of the projector.

•To avoid injury to yourself and damage to the lamp,
make sure you carefully follow the steps below.

• Do not loosen other screws except for the lamp unit
cover and lamp unit.

STANDBY/ON button

AC socket

1 Press STANDBY/ON on the projector

or STANDBY on the remote control to
put the projector into standby mode.

•Wait until the cooling fan stops.

5 Insert the new lamp unit.

• Press the lamp unit firmly into the lamp unit
compartment. Fasten the securing screws.

6 Replace the lamp unit cover.

• Align the tab on the lamp unit cover (1) and
place it while pressing the tab (2) to close it.
Then tighten the user service screw (3) to se­cure the lamp unit cover.

Info

• If the lamp unit and lamp unit cover are not cor­rectly installed, the power will not turn on, even if
the power cord is connected to the projector.

Resetting the Lamp Timer

Reset the lamp timer after replacing the lamp.

Info

• Make sure to reset the lamp timer only when re­placing the lamp. If you reset the lamp timer and
continue to use the same lamp, this may cause the
lamp to become damaged or explode.

1 Connect the power cord.

• Plug the power cord into the AC socket of the
projector.

2 Reset the lamp timer.

• While simultaneously holding down
MENU/HELP, ENTER and R on the projector,
press STANDBY/ON on the projector.

• “LAMP 0000H” is displayed, indicating that the
lamp timer is reset.

Securing screws

AC socket

STANDBY/ON
button

ENTER button

MENU/HELP
button

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down
(about 1 hour).

3 Remove the lamp unit cover.

•Turn the projector over. Loosen the user ser­vice screw (1) that secures the lamp unit cover.
Remove the lamp unit cover (2).

R button

User service screw
(for lamp unit cover)

Printed in China
TINS-D168WJZZ
07P07-CH-NM

DEUTSCH

FRANÇAIS

ESPAÑOL

ITALIANO

NEDERLANDS

SVENSKA

PORTUGUÊS

Richten Sie sich bitte nach der beim Projektor mitgelieferten
Bedienungsanleitung.
Sie können die Bedienungsanleitung auch von der Website
(http://sharp-world.com/products/index.html) herunterladen.

Reportez-vous au mode d’emploi fourni avec le projecteur.
Vous pouvez également télécharger le mode d’emploi sur le site
Internet (http://sharp-world.com/products/index.html).

Consulte el manual de manejo que se suministra con el proyector.
También puede descargar el manual de manejo del sitio Web
(http://sharp-world.com/products/index.html).

Fare riferimento al manuale d’uso fornito con il proiettore.
È inoltre possibile scaricare lo stesso manuale d’uso dal sito web
(http://sharp-world.com/products/index.html).

Verwijs naar de gebruiksaanwijzing die bij de projector wordt
geleverd.
U kunt de gebruiksaanwijzing ook vanaf internet downloaden
(http://sharp-world.com/products/index.html).

Anlita bruksanvisningen som medföljer projektorn.
Bruksanvisningen kan också nerladdas från vår webbsajt
(http://sharp-world.com/products/index.html).

Consulte o manual de operação fornecido com o projetor.
Pode-se também baixar o manual de operação pela internet
(http://sharp-world.com/products/index.html).