Sharp AN-C430LP Installation Manual

LAMP UNIT (LAMP/CAGE MODULE) FOR PROJECTOR

Securing screws

Info

STANDBY/ON button

AC socket

User service screw (for lamp unit cover)

AC socket

" button

ENTER button

STANDBY/ON button

MENU button

Model AN-C430LP

INSTALLATION MANUAL

CAUTION:

••

• Potential hazard of glass particles if lamp ruptures. In case of lamp rupture, contact your nearest Sharp

••

Authorized Projector Dealer or Service Center* for replacement.

••

• Do not remove the lamp unit from the projector right after use. The lamp will be very hot and may cause burn

••

or injury. Wait at least one hour after the power cord is disconnected to allow the surface of the lamp unit to fully cool before removing the lamp unit.

■

It is recommended that the lamp unit be replaced when the remaining lamp life becomes 5% or less, or when you notice a significant deterioration in the picture and color quality. The lamp life (percentage) can be checked with the on-screen display.

IMPORTANT NOTE TO U.S. CUSTOMERS:

The lamp included with this projector is backed by a 90-day parts and labor limited warranty. All service of this projector under warranty, including lamp replacement, must be obtained through a Sharp Authorized Projector Dealer or Service Center*. For the name of the nearest Sharp Authorized Projector Dealer or Service Center*, please call toll-free: 1-888-GO-SHARP (1-888-467-4277).

Hg LAMP CONTAINS MERCURY For State Lamp Disposal Information www.lamprecycle.org or 1-800-BE-SHARP U.S.A. ONLY

* Confirm the name of the Dealer or Service Center referring to your projector operation manual.

Removing and Installing the Lamp Unit

Warning!

• Do not remove the lamp unit from the projector right after use. The lamp and parts around the lamp will be very hot and may cause burn or injury.

4 Remove the lamp unit.

• Loosen the securing screws from the lamp unit. Hold the lamp unit and pull it in the direction of the arrow. At this time, keep the lamp unit horizontal and do not tilt it.

5 Insert the new lamp unit.

• Press the lamp unit firmly into the lamp unit compartment. Fasten the securing screws.

6 Replace the lamp unit cover.

• Align the lamp unit cover and slide it to close. Then tighten the user service screw to secure the lamp unit cover.

• If the lamp unit and lamp unit cover are not correctly installed, the power will not turn on, even if the power cord is connected to the projector.

Resetting the Lamp Timer

• Do not touch the glass surface of the lamp unit or the inside of the projector.

• To avoid injury to yourself and damage to the lamp, make sure you carefully follow the steps below.

• Do not loosen other screws except for the lamp unit cover and lamp unit.

1 Press STANDBY/ON on the projec-

tor or trol to put the projector into standby

mode.

• Wait until the cooling fan stops.

2 Disconnect the power cord.

• Unplug the power cord from the AC socket.

• Leave the lamp until it has fully cooled down

(about 1 hour).

3 Remove the lamp unit cover.

• Loosen the user service screw (1) that se- cures the lamp unit cover. Slide down (2) and remove the lamp unit cover (3).

STANDBY on the remote con-

Reset the lamp timer after replacing the lamp.

• Make sure to reset the lamp timer only when replacing the lamp. If you reset the lamp timer and continue to use the same lamp, this may cause the lamp to become damaged or explode.

1 Connect the power cord.

• Plug the power cord into the AC socket of the projector.

2 Reset the lamp timer.

•

While simultaneously

MENU on the projector, press STANDBY/

ON on the projector.

• “LAMP 0000H” is displayed, indicating that the lamp timer is reset.

holding down ", and

Printed in China TINS-C573WJZZ 06P07-CH-NM

Für Anweisungen in Ihrer Sprache siehe Benutzerhandbuch im PDF-Format auf der mit dem Projektor mitgelieferten CD-ROM. Sie können das PDF-Benutzerhandbuch auch aus dem Internet herunterladen (http://sharp-world.com/products/index.html).

DEUTSCH

Pour des instructions dans votre langue, reportez-vous au mode d’emploi PDF contenu dans le CD-ROM fourni avec le projecteur. Vous pouvez également télécharger le mode d’emploi PDF d’Internet (http://sharp-world.com/products/index.html).

FRANÇAIS

Para recibir instrucciones en su idioma, consulte el manual de manejo PDF que se encuentra en el CD-ROM suministrado con el proyector. También puede descargar el manual de manejo PDF de Internet (http://sharp-world.com/products/index.html).

ESPAÑOL

Per ricevere istruzioni nella propria lingua, fare riferimento al manuale d’uso in formato PDF incluso nel CD-ROM fornito con il proiettore. È possibile, inoltre, scaricare lo stesso manuale d’uso da Internet dal sito http://sharp-world.com/products/index.html .

ITALIANO

Voor aanwijzingen in uw taal verwijzen wij u naar de PDFgebruiksaanwijzing op de CD-ROM die bij de projector wordt geleverd. U kunt de PDF-gebruiksaanwijzing ook vanaf internet downloaden (http://sharp-world.com/products/index.html).

NEDERLANDS

Vi hänvisar till de PDF-filer som återfinns på den medföljande CD-ROMskivan för en bruksanvisning på önskat språk. En bruksanvisning av formatet PDF kan också nerladdas från Internet (http://sharp-world.com/products/index.html).

SVENSKA

Para instruções no seu idioma, consulte o manual de operação em PDF contido no CD-ROM fornecido com o projetor. Pode-se também baixar o manual de operação em PDF pela internet (http://sharp-world.com/products/index.html).

PORTUGUÊS