Sharp 28KF-84H, 32KF-84H Owner Manual

Download

Page 1

28KF-84H 32KF-84H

COLOUR TELEVISION

OPERATION MANUAL

Please read this operation manual carefully before using the colour television.

PRINTED ON ENVIRONMENTALLY FRIENDLY PAPER

Page 2

TERMS OF GUARANTEE

Subject to the conditions listed below Sharp Electronics (U.K.) Ltd.(Hereinafter called «the Company») guarantee to provide for the repair of, or at its option replace the Sharp Equipment, or any component thereof, (other than Batteries), which is faulty or below standard, as a result of inferior workmanship or materials.

The conditions of the Guarantee are:

1. This guarantee shall only apply to defects or faults which are notified to the Company, or its approved Service Facility within one year from the date of purchase of the equipment.

2. This guarantee covers equipment intended f or priv ate domestic use only.This guarantee does not apply to equipment used in the course of a business, trade or profession.

3. This guarantee does not cover any faults or defects caused by accident, misuse, fair wear and tear, neglect, tampering with the equipment, or any attempt at adjustment or repair other than by an approved Service Facility.

4. In the unlikely event of that your equipment should require repair, please contact the dealer or supplier from whom it was purchased.

5. The cost of carriage to and from the Dealer, Supplier or Sharp approved Service F acility shall be borne by the purchaser.

6. No person has any authority to vary the terms or conditions of this guarantee.

7. This guarantee is offered as an additional benefit to the consumer’s statutory rights and

does not affect rights in any way.

In the unlikely event of this equipment requiring repair during the guarantee period, you will need to provide proof of date of purchase to the repairing company. Please keep your invoice or receipt, which is supplied at the time of purchase.

Page 3

Safety Precautions

The tube of your TV has a special coating. Do not knock or rub on the tube face with sharp or hard surfaces, otherwise you will damage the coating. To prevent damaging the surface of the television screen, remove finger prints only with a soft cloth dampened with glass cleaner. Do not use any abrasive cleaners. Do not use thinner, benzene or other strong chemical cleaners.

To prevent fire or electrical shock, do not use the TV set in an excessively damp place.

Position the TV set out of direct sunlight and away from heat, as high temperatures can damage the cabinet, CRT, or other electronic parts.

Don't cover ventilation salts with objects such as newspapers, tablecloths, curtains, etc. Do not cover the ventilation holes at the back of the TV set, this can cause fire or other serious problems. Leave an adequate open space behind the TV set for good ventilation.

Always disconnect your television from the mains and the aerial cables during thunderstorms. Even if your television is switched off, it can still be damaged by lightning striking the mains and/or aerial cable.

Unplug the power cord from the wall outlet immediately if the TV set begins to make unusual noises or give off smoke or an odd smell, then call your dealer for service.

In order to ensure that the television is properly ventilated, leave a space of at least 10 cm around the set. Do not install this equipment in a confined space such as a bookcase or a built-in cabinet.

Television equipment and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the equipment and cart combination to overturn.

Wall or shelf mounting should follow the manufacturer's instructions, and should use a mounting kit approved by the manufacturer.

To prevent electrical shock, do not subject the AC power cord to damage by bending or twisting it, or by placing heavy items on top of it and do not place the AC power cord under the TV set. If the AC power cord becomes damaged, unplug it from the wall outlet immediately and call your dealer for service.

Do place the TV set onto an even stand, table or track which size is bigger than the TV set. If the TV set is put onto a smaller size or uneven stand, table or track may cause the TV cabinet distort. Do not put or insert anything between TV set and the stand, table or track.

In order to prevent electrical shocks and fires, ensure that the television is not subjected to splashes or spills of water, and avoid inserting objects or pouring any type of liquid into the set. To prevent fire, never place any type of candle or naked flames on the top or near the TV set. In the case that an object or liquid enters the set, don't use and contact technical service.

Never remove the back of the cabinet, as there is high voltage in the TV set. Please call for service.

Do not place this television equipment on an unstable cart, stand, or table. The television equipment may fall, causing serious injury to a child or an adult, and serious damage to the equipment. Use only with a cart or stand recommended by the manufacturer, or sold with the television equipment.

CAUTION: For environmental and safety reasons, it is recommended that the

television isn't left in stand-by mode while not in use. Switch it off using the main

button and unplug it during periods of absence from the home.

This equipment complies with the requirements of Directives 89/336/EEC, 92/31/EEC and 73/23/EEC as amended by 93/68/EEC.

Page 4

Congratulations! You are now the proud owner of a SHARP Colour Television Receiver. To ensure proper operation, please read this manual carefully. After reading, keep this manual in a safe place for future reference.

Dear SHARP Customer

Remote Control Battery Installation

Contents

Terms of guarantee ......................................................... 1

Safety precaution ............................................................ 2

Contents ......................................................................... 3

Accessories .................................................................... 3

Remote Control Battery Installation ................................ 3

Remote Control buttons ................................................. 4

Controls and Terminals ................................................... 5

Typical Connections (Aerial, VCR, DVD, etc.).................. 6

Auto Installation ............................................................ 11

Switching on ................................................................. 13

TV operation (Channel selection) .................................. 14

Menu Structures.............................................................15

Picture Adjustments ..................................................... 16

100 Hz Fast Menu ......................................................... 18

Wide Mode ................................................................... 19

Audio Adjustments .........................................................21

Sound Setting Mode.......................................................22

Features setting mode:

On Timer and Off Timer ................................................ 24

Child Lock (Channel Block) .......................................... 25

Demo ............................................................................ 26

Postcode Security ........................................................ 27

TV Channel Setting (Advanced):

To repeat the AUTO INSTALLATION ............................ 29

Manual Channel Preset ................................................. 30

After preset has been performed (Fine-tuning) ............. 32

TV/VIDEO Selector, Clock button, Headphone Jack

and Sub-titles button..................................................... 34

VCR Mode .................................................................... 35

Teletext Mode ............................................................... 36

21-pin Euro-SCART and 21-pin Audio/Video ............... 39

Troubleshooting ............................................................ 40

General Specifications for Television Receiver ............ 41

Index page .................................................................... 42

Remote control

Before using the TV set for the first time, install the supplied dry batteries in the remote control.

• Remove batteries if weak or if the unit is not in use for long periods.

• Do not mix old and new batteries.

• Incorrect installation of the batteries may damage the remote control.

Note:

1. With your thumb nail, pull up

the slit as indicated by the arrow to remove the battery cover.

2. Insert two batteries 1.5 V (R-6

"AA" size). Be sure to match the battery

±/— terminals with the

±/—marks inside the

compartment.

3. Replace the battery cover.

Respect the

environment and

put used batteries

in a container that is

especially designed

for this purpose.

Supplied Accessories

Note:

Typical

Connections

Quick Start

Guide

Operation

Manual

Type-AA

Dry-Batteries

Aerial connection - TV set only -

BACK OF TV

Aerial

(Not supplied)

Aerial IN

Aerial Connections - TV and VCR -

BACK OF TV

(Not supplied)

Aerial IN

Aerial Lead (Not supplied)

Scart Lead (Not supplied)

RF OUT

Audio/Video

Aerial IN

28/32KF-84H

Aerial Lead (Not supplied)

Aerial

Aerial Lead (Not supplied)

28KF-84H 32KF-84H

COLOUR TELEVISION

QUICK

START GUIDE

For easy installation

● Fitting the batteries into the remote control

● Connecting the aerial cable

● Tuning the TV channels

Using this installation guide should enable you to set up your TV in less than 15 minutes - - -

- - - Please refer to your operation manual for more tips and advice.

If problems persist, contact the SHARP Helpline (office hours only) on tel: 08705 274277 (or (01) 676 0648 if telephoning from Ireland) and/or WEB-SITE: www.sharp.co.uk/support

Typical Connections

AV/TERMINAL

(AV-1)

BACK OF VCR

For further details, please refer to operation manual of your VCR.

28KF-84H 32KF-84H

COLOUR TELEVISION OPERATION MANUAL

Please read this operation manual carefully before using the colour television.

PRINTED ON ENVIRONMENTALLY FRIENDLY PAPER

Page 5

Remote control buttons

TV 1. Stand-by ON/OFF switch (TV) Video 2. Power ON / OFF switch (VCR) TV 3. Digit buttons 0 ~ 9

4. Flashback button

Teletext 5. Green button

6. Red button

TV 7. Volume Down/Cursor control Left

8. Menu button

Teletext 9. Reveal button

10. List selector

11. Store button

12. Cancel button

13. Top/ Bottom/Full button

14. Reset button

Video 15. Rewind/picture search/reverse

16. Play button

17. Pause / Still button

18. Stop button

TV 19. TV/VIDEO selector

20. 100 Hz Fast Menu button

21. Single/Double entry

Teletext 22. Yellow button

23. Blue button

TV 24. Channel Up/Cursor control Up

25. Volume Up/Cursor control Right

26. Channel Down/Cursor control Down

27. Wide Mode Selector TV/Teletext 28. Time button TV 29. Sound mode selector Teletext 30. Hold button TV 31. Sound Mute button Teletext 32. Text/Mix/Picture button

33. Index button Video 34. Channel Up selector

35. Fast forward/picture search/forward

36. Channel Down selector

37. Record button

1. 19.

23.

21.

24.

25.

26.

27.

28.

29.

30.

31.

32.

34.

37.

36.

35.

33.

22.

20.

10.

11.

12.

13.

15.

18.

17.

16.

14.

Page 6

Controls and Terminals

FRONT TV

1. Main Power On/Off Switch

2. Power Indicator

3. Remote Control Sensor

4. Door

HOW TO OPEN THE DOOR

Put the finger in the lower part of the door and press upward.

Behind the door

5. Volume Button (DOWN)

6. Volume Button (UP)

7. Program Selector (NEXT)

8. Program Selector (PREVIOUS)

9. S-Video input terminal

10. Video Input Terminal (PAL/SECAM/NTSC)

11. Audio Input Terminal (left)

12. Audio Input Terminal (right)

13. Headphone Socket (3.5mm Ø, 16~600 ohms)

REAR TV 21-pin In/Out

1. 21-pin Audio/Video (AV-1) With

PAL/SECAM/NTSC/S-Video Input

2. 21-pin Euro SCART (RGB) With PAL/SECAM/NTSC Video Input

RF Input

3. Aerial terminal

1 2 3 4

5 6 7 8

10 11 12 13

31 2

Page 7

Typical Connections

Aerial connection - TV set only -

Aerial Connections - TV and VCR -

For further details, please refer to operation manual of your VCR.

Note:

BACK OF TV

BACK OF VCR

Aerial

(Not supplied)

Aerial

(Not supplied)

Aerial Lead (Not supplied)

Aerial IN

Audio/Video

Scart Lead (Not supplied)

RF OUT

AV/TERMINAL

(AV-1)

Aerial IN

Page 8

Typical Connections (Continued)

Connections - TV, DECODER and VCR (Videorecorder) -

For further details, please refer to operation manuals of your DECODER and DVD Player.

Note:

BACK OF TV

DECODER

Aerial

(Not supplied)

Scart Lead

(Not supplied)

AV/TERMINAL

(AV1)

Aerial IN

Aerial Lead (Not supplied)

Scart Lead

(Not supplied)

Audio/Video

RF OUT

Aerial Lead

(Not supplied)

BLACK OF VCR

Euro

SCART

(RGB)

Aerial Lead

(Not supplied)

BACK OF TV

DECODER

Scart lead (Not supplied)

AV/TERMINAL

(AV1)

Scart Lead (Not supplied)

Euro

SCART

(RGB)

Connections - TV, DECODER and DVD Player -

For further details, please refer to operation manuals of your DECODER and VCR.

Note:

Aerial

(Not supplied)

DVD

PLAYER

Page 9

Connections - TV

, DVD Player and Digital Set Top Box -

Typiccal Connections (Continued)

For further details, please refer to operation manuals of your DVD Player and Digital Set Top Box.

Note:

BACK OF TV

DVD PLAYER

Scart Lead

(Not supplied)

Aerial Lead

(Not supplied)

AV/TERMINAL

(AV 1)

Euro

SCART

(RGB)

Aerial IN

Scart Lead (Not supplied)

Dish Lead (Not supplied)

DISH IN

AERIAL IN

TV SCART

RF OUT

Satellite dish (Not supplied)

Aerial

(Not supplied)

Aerial Lead (Not supplied)

DIGITAL SET

TOP BOX

Page 10

Connections - TV, VCR and Digital Set Top Box -

Typical Connections (Continued)

For further details, please refer to operation manuals of your VCR and Digital Set Top Box.

Note:

BACK OF TV

Scart Lead

(Not supplied)

AV/TERMINAL

(AV1)

Euro

SCART

(RGB)

Aerial IN

Audio / Vídeo

Aerial Lead (Not supplied)

DISH IN

AERIAL IN

TV SCART

RF OUT

Satellite dish (Not supplied)

Aerial

(Not supplied)

Aerial Lead (Not supplied)

BACK OF VCR

DIGITAL SET

TOP BOX

RF OUT

Scart Lead

(Not supplied)

Scart Lead

(Not supplied)

Aerial Lead (Not supplied)

Dish Lead (Not supplied)

Page 11

Front connections -TV and V

ideo camera-

Connection-TV power cable to a 220 ~ 240 V system -

Typical Connections (Continued)

For further details, please refer to operation manual of your Video Camera.

Note:

FRONT TV

(Behind the door)

BACK OF TV

S-Video lead (Hi-8)

(Not supplied)

Audio/Video lead

(Not supplied)

WIEW CAM

Mains Socket Outlet

AC 220~240 V, 50 Hz

S-Video Input Terminal (Hi-8)

Video Input Terminal

Audio Input Terminal (left)

Audio Input Terminal (right)

Page 12

■ Auto Installation System (AIS)

Your television set is provided with an Automatic Installation System which makes Installation easier. This new system is activated when you turn on the TV for the first time.

You may not have to follow this procedure if it has already been done for you at the establishment where you purchased your TV. If this is the case, go on to the section entitled -Switching ON- (page 13).

Procedure:

1. Put batteries into the remote control, as shown on page 3.

2. Connect the aerial jack into the aerial input terminal on the rear

side of your TV, as shown on page 6.

3. Connect the TV power cable to a 220 ~ 240 V system, as shown

on page 10.

Press the main power button (®), on the front of the TV set, to start the “AUTO INSTALLATION”. The orange power indicator will light..

5. The «AUTO INSTALLATION» menu will appear on your TV screen.

 The TV is ready to preset automatically all local channels for you.  If the TV is being used with a VCR, turn on the VCR and play

back a pre-recorded tape. The signal from the RF terminal of your VCR is assigned to a TV channel.

6. Now, press any button on the TV remote control to start Auto

Channel Preset.

The TV will go through the following steps automatically and sequentially:

Automatic Channel Sorting System (ACSS): The TV set SEARCHES FOR FREQUENCIES, memorises the channels found, and sorts them (according to technical criteria) from Pr-01 of the TV, to a maximum of 99 programmes.

This tuning process may take several minutes to perform. If you need to repeat the “AUTO INSTALLATION”, go on to the section entitled -TV Channel Setting- (page 29).

Editing: When the TV has finished the automatic search, the «Stored programmes» menu will appears on the screen. In this menu, you can change the order of the channels and change or give the channels a four-letter name.

On next page is a detailed explanation of editing options about

«Stored programmes» menu.

Auto Installation

Be sure the antenna cable is connected…

Press any button on the handset to start.

SHARP

AUTOINSTALLATION

VÍDEO

Power Indicator

Main power button

Note:

«AUTO INSTALLATION»

VCR

Searching

please wait

Pr 01

01 %

Searching

Note:

Page 13

b) «Edit this program»  RED button . c) «Go to sorting mode»  GREEN button . d) «Delete this program»  YELLOW button .

e) «Exit this menu»  BLUE button . With these options, you will be able to organise the real channels (CH **) memorised in the TV programmes (Pr 01 ... Pr 99) and put them into your own preferred order. The following is a detailed explanation of options a), b), c), d) and e).

a) Select a programme to be edited.

Use this option to select a programme

from the list. Each time you press

/ the memorised channel will be viewed and will remain

selected on the list by means of white letters.

b) «Edit this program» (Change of name)

Use this option for giving a name

made up of four digits to the channels or for changing the one, which appears on some channels, in the following way: b.1 Select the channel using the Cursor UP/DOWN buttons / (marked in white letters).

b.2 Press the RED button to see the Edit name mode. b.3 Press the Cursor UP button to change the first letter.

Letters A to Z of the alphabet, a blank space and the numbers 0 to 9 will appear sequentially. Some of the broadcasting stations names such as BBC1 or ITV are already incorporated in the TV and appear among the alphabet to make this task easier. Press the Cursor DOWN button to go backwards in the sequence.

b.4 Press the buttons for changing the position of the cursor and the

/ buttons for changing the letters (repeat this action for other

letters). When you have finished the fourth letter, press the Cursor button to quit the Change of Name option.

c) «Go to sorting mode» (Sorting channels)

Use this option for sorting the channels

(CH) into the desired programme

(Pr), as follows: c.1 Select the programme (Pr) you wish to change using Cursor

UP/DOWN buttons / (marked in white letters).

c.2 Press the GREEN button to see the Sorting mode. c.3 Press the Cursor UP/DOWN buttons / to move the

channel (CH) to the required position (marked in red letters on a black background).

c.4 Press the GREEN button to finish.

d) «Delete this program» (Delete channels)

Use this option for cancelling programmes

, which are badly tuned or repeated. d.1 Select the channel you wish to delete using Cursor UP/DOWN buttons

/ (marked in white letters).

d.2 Press the YELLOW button to see the Delete mode. d.3 The TV will ask for confirmation that you wish to cancel, and you must

press the YELLOW button again. The channels that follow it on the list will automatically rearrange themselves by moving up one programme (Pr) place, to restore the space of the cancelled channel (CH).

e) «Exit this menu»

Use this option to quit the menu by pressing the BLUE button .

Stored programmes

When the TV has finished the automatic search, the «Stored programmes» menu will appear on screen with a list of the channels, which have been memorised with the available options:

a) Select programme to be edited  / .

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

Press the MENU button to exit.

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

Insert the marked programme in the position you wish.

Press green button to finish.

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

WARNING!

This programme

will be erased.

Press yellow button again

to confirm. Or press any other button

to cancel

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:



Edit this program



Go to sorting mode



Delete this program



Exit this menu

(red)

(green)

(yellow)

(blue)

«Stored programmes» menu

«Edit this program» Edit name mode

«Go to sorting mode» Sorting mode

«Delete this program» Delete mode

Page 14

Switching on

This TV memorizes the Mode last used when it was switched off. When the main power button (®) is pressed to turn on the set, the power indicator will light and the set will resume in either the Stand-by mode

or Programme

mode

, depending upon its condition when it was switched off.

When the TV is in Stand-by mode

, to turn ON the TV press the Stand-by button ( TV) on the remote control, or one of the four buttons on the TV (

V/\, VCH/\

). The TV will change from Stand-by mode to Program mode and an image will appear on the screen. Press the Stand-by button ( TV) again and the TV will return to Stand-by mode

If noise appears in TV or VCR mode, the screen turns blue. The blue back off-timer is then engaged and will automatically switch the set to Stand-by mode after 15 minutes.

Power supply on/off buton

On-Off/Stand-by button

Blue back off timer

Power Indicator

Main power button

Page 15

TV Operation

 Channel selector CH

/CH Ù buttons

Select the programme channel number you want to see, using the channel selector buttons (

/ ).

As you press these buttons a list of channels appears.

Press the

/ again to select another channel.

The channels that are in SKIP mode cannot be seen with these buttons. Use numerical buttons to display these channels.

 Single/Double entry selector

This button selects between one or two digit channel number entry.

 0~9 Digit buttons

You can select channels by pressing the 0 ~ 9 digit buttons on the remote control. For single and double-digit entry see section B above.

 Flashback button

Press this button to switch the currently viewed channel to the previously viewed channel, and vice versa. This function is only available in programme channel selection mode. I.e. not when AV terminals are in use.

Press

PR *

Single digit entry mode

PR * *

Double digit

entry mode

Press

PR 01

Previously

viewed channel

PR 12

Currently

viewed channel

Pr 01 Pr 02  Pr 03 Pr 04 Pr 05 Pr 06 Pr 07 Pr 08 Pr 09 Pr 10

Channel Selection

Note:

Page 16

Menu Functions / Options

CHANNEL: CH (Aerial) / CC (Cable) SEARCH (Frequency Tuning) FINE TUNE MODE: TV / VCR / SKIP EDIT: Edit this program / Go to sorting mode / Delete this program / Exit this menu AUTO-TUNE: AUTO INSTALLATION

Menu Structures

This TV set has: a MAIN MENU with four basic menus, which permit access to the different functions of the TV.

These menus are as indicated below.

MENU Button

By pressing the MENU Button :

CONTRAST COLOUR BRIGHTNESS SHARPNESS NORMALISE TINT CONTROL ECO MODE NOISE REDUCTOR BLACK STRETCHER ROTATION SVM

VOLUME EQUALIZER LOUDNESS BALANCE NORMALISE LOUDSPEAKERS (MODE) EFFECTS SOUND IDENTIFICATION

ON TIMER: TIME / SWITCH ON OFF TIMER: OFF / 120 Min. / 90 Min. / 60 Min. / 30 Min. CHILD LOCK: LOCK ALL / LOCK PROGRAMME / CLEAR LOCK DEMO POST CODE

VOLUME BASS TREBLE BALANCE NORMALISE HEADPHONES (MODE)

LOUDSPEAKERS

HEADPHONES

PICTURE

ADJUSTMENTS

AUDIO

ADJUSTMENTS

OTHER

FUNCTIONS

INSTALL

AND TUNE

Page 17

Picture quality (CONTRAST, COLOUR, BRIGHTNESS, SHARPNESS, NORMALISE, TINT CONTROL, ECO MODE, NOISE REDUCTOR, BLACK STRETCHER, ROTATION and SVM) are adjustable in this menu.

1. Press the MENU button to see the MAIN Menu.

MAIN Menu

2. Press the MENU button to see the PICTURE Menu.

PICTURE Menu

3. Press the Cursor UP/DOWN buttons

/ to select an

option from the list: «CONTRAST», «COLOUR», «BRIGHTNESS», «SHARPNESS», «NORMALISE», «TINT CONTROL», «ECO MODE», «NOISE REDUCTOR», «BLACK STRETCHER», «ROTATION» or «SVM».

The selected item will appear on screen in a blue box.

4. Adjust the picture quality to your liking with the Cursor LEFT/RIGHT buttons / .

NORMALISE Menu

5. Press the MENU button if you wish to normalize video levels

to default factory settings.

6. Press the Cursor DOWN button to see more options.

TINT CONTROL

7 Select «TINT CONTROL» and press the Cursor LEFT/RIGHT

buttons / to adjust your desired skin colour (blue or red).

Picture Adjustments

Picture Menu



NORMALISE

SHARPNESS

BRIGHTNESS

COLOUR

CONTRAST

➜

NORMALISE

SHARPNESS

BRIGHTNESS

COLOUR

CONTRAST

➜

TINT CONTROL

ECO MODE

NOISE

REDUCTOR

TINT

CONTROL

Press the MENU

button to

normalise...

NORMALISE Menu

➜

ROTATION

BLACK STRETCHER

MAIN Menu

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

Page 18

ECO MODE

8. Select «ECO MODE» and press the Cursor LEFT/RIGHT buttons

/ to reduce contrast in areas of the picture those are

excessively white (ON or OFF).

NOISE REDUCTOR

9. Select «NOISE REDUCTOR» and press the Cursor LEFT/RIGHT

buttons / to reduce the noise when receiving a weak signal and improve the picture quality (OFF, AUTO, MEDIUM or HIGH).

BLACK STRETCHER

10. Select «BLACK STRETCHER» and press the Cursor

LEFT/RIGHT buttons / to connect or disconnect (ON or OFF) the Dynamic Compensation in dark area of the picture.

ROTATION

11. If the picture is tilted, select Rotation and press the Cursor

LEFT/RIGHT buttons / to adjust the picture tilt.

12. Press the Cursor DOWN button to see more options.

SVM

13. Select SVM (Scan Velocity Modulator) and press the Cursor

LEFT/RIGHT buttons / to change the resolution of the picture (ON or OFF).

14. Press the MENU button to close the Menu.

ECO MODE

NOISE

REDUCTOR

TINT

CONTROL

➜

ROTATION

BLACK

STRETCHER

BLACK STRETCHER

ECO MODE

NOISE REDUCTOR

TINT

CONTROL

➜

ROTATION

BLACK

STRETCHER

OFF

ROTATION

ECO MODE

NOISE REDUCTOR

TINT

CONTROL

➜

ROTATION

BLACK

STRETCHER

NOISE REDUCTOR

ECO MODE

NOISE

REDUCTOR

TINT

CONTROL

➜

ROTATION

BLACK

STRETCHER

OFF

SVM

➜

OFF

Page 19

100 Hz Fast Menu

With this menu you can enter to the following functions: STILL Mode (Frozen picture), SCOPE Mode (Enlarge picture) and PICTURE MODE (Settings Audio and Video).

1. Press the 100 Hz FAST MENU button

lto see the 100 Hz Fast Menu.

100 Hz Fast Menu

2. Press the corresponding coloured button:

Press the RED button «STILL» to freeze the picture. Press the GREEN button «SCOPE» to enlarge picture. Press the YELLOW button «PICTURE MODE» to change the audio and video Settings. Press the BLUE button «EXIT» to quit the Menu.

STILL Mode

In this mode the TV set freezes the picture. You can also enter to the following functions: «STILL» ON/OFF by RED button . «SCOPE» ON/OFF by GREEN button . «PICTURE MODE» by YELLOW button . «EXIT» by BLUE button .

SCOPE Mode

In this mode you can enlarge and move the picture by means of UP/DOWN/LEFT/RIGHT buttons E/F/

C/I.

You can also enter to the following functions: «STILL» ON/OFF by RED button . «SCOPE» ON/OFF by GREEN button . «EXIT» by BLUE button .

PICTURE Mode

Press the YELLOW button «PICTURE MODE» to select a predetermined level (Video and Audio): FACTORY SETTINGS / CINEMA / CINEMA PLUS / SOFT / PERSONAL / SPORT / RICH / FILMS. You can also enter to the following functions: «STILL» ON/OFF by RED button . «SCOPE» ON/OFF by GREEN button . «PICTURE MODE» by YELLOW button . «EXIT» by BLUE button .

100 Hz Fast Menu

RED GREEN

YELLOW

BLUE

(NORMAL PICTURE)

STILL Mode

(FROZEN PICTURE)

FACTORY SETTINGS

STILL ON

SCOPE Mode

(ENLARGE PICTURE)

SCOPE ON

PICTURE MODE

FACTORY SETTINGS

STILL

SCOPE

PICTURE

MODE

EXIT

STILL

SCOPE

PICTURE

MODE

EXIT

RED GREEN

YELLOW

BLUE

RED GREEN

BLUE

STILL

SCOPE EXIT

STILL

SCOPE

PICTURE

MODE

EXIT

RED GREEN

YELLOW

BLUE

FACTORY SETTINGS

Page 20

Wide Mode Menu

With this menu you can select the width of the picture: AUTO, PANORAMA, FULL, NORMAL, ZOOM 14:9 or CINEMA, by pressing

the WIDE MODE button .

Each time you press the WIDE MODE button , the width of the picture changes as indicated:

AUTO * ➔ PANORAMA ➔ FULL ➔ NORMAL ➔ ZOOM 14:9 ➔ CINEMA

When you Select: PANORAMA, ZOOM 14:9 or CINEMA, 4 options appear on the screen:

 V-SCROLL: Press the RED button to see the Vertical SCROLL menu.

 V-SIZE: Press the GREEN button to see the Vertical SIZE menu.

 NORMAL: Press the YELLOW button to normalize the Vertical SCROLL and Vertical SIZE.

 EXIT: Press the BLUE button to quit the menu.

 V-SCROLL menu: Press the Cursor LEFT/RIGHT buttons /

to adjust the Vertical SCROLL (UP/DOWN).  V-SIZE menu: Press the Cursor LEFT/RIGHT buttons / to

adjust the Vertical SIZE (LARGE/SMALL).

* AUTO mode (VPS code): The VPS signal is sent by some

broadcasting stations with information of the original size. When the TV is in AUTO mode and receives the VPS signal, it changes the size automatically as indicated below:

When the TV is receiving VPS code 16:9 the TV selects

CINEMA automatically.

When the TV is receiving VPS code 14:9 the TV selects ZOOM

14:9 automatically.

When the TV is receiving VPS code 4:3 the TV selects

PANORAMA automatically.

When the TV does NOT receive VPS code the TV selects

PANORAMA automatically.

External source: When you are watching the TV-set through the Euro-SCART or AV-1 terminals and it receives information of 16:9 format (through the audio-video control pin) the TV selects FULL

automatically.

WIDE MODE

button

Vertical SIZE menu

Vertical SCROLL Menu

BLUE

EXIT

V-SCROLL

V-SIZE

V-SCROLL

V-SIZE

NORMAL

EXIT

RED GREEN YELLOW BLUE

BLUE

DOWN

SMALL

LARGE

AUTO.

PANORAMA

Page 21

PANORAMA

The Panorama Mode adapts the broadcast picture to 16:9 format without changing the centre of view. This is especially useful for programmes like the News when the speaker in the centre of the picture needs to be seen clearly.

FULL

With Full Mode you adapt the picture 16:9 format while also stretching the centre of view. This is an advantage, for example, when watching sports games where there is no real fixed centre of the picture.

NORMAL

You can watch 4:3 programs in 4:3 format by switching to Normal Mode function.

ZOOM 14:9

Adapts the 14:9 broadcast cinema movies to the 14:9 Mode.

CINE (16:9)

Adapts the 16:9 broadcast cinema movies to the 16:9 Mode, thereby getting rid of the black borders.

Special detail information about PANORAMA, FULL, NORMAL, ZOOM 14:9 and CINEMA (16:9).

16:9

4:3

Wide Mode (Special detail information)

Page 22

Audio Adjustments

 Loudspeakers Sound Volume /

Use the / buttons to increase/decrease the volume level. The volume indicator will appear on the screen.

To adjust the headphones volume, go on to the section entitled -SOUND menu- (page 22).

 Sound mute button

Press the button to mute the sound. «MUTE» appears on the screen. Press the button again to turn the sound back on.

 Sound Mode Selector button

Press the button to change the sound in the speakers. The sound mode will appear on the screen.

Depending on the sound transmission the sound reproduction can be chosen as indicated below:

When the TV set is receiving a STEREO programme, the TV selects STEREO automatically, and you can change:

STEREOMONO

When the TV is receiving a BILINGUAL programme, the TV selects DUAL CHANNEL A automatically, and you can change:

DUAL CHANNEL ADUAL CHANNEL BDUAL CHANNEL A B MONO

When the TV is receiving a MONO (NICAM) programme, the TV set selects MONO NICAM automatically, and you can change:

MONO NICAMMONO (FM)

When the TV is receiving a MONO (FM) programme, the TV set selects MONO automatically but the sound mode cannot be change.

See the -SOUND MODE- (page 23) to change the Sound Mode in the headphones.

External source: When you are watching the TV-set through the Euro-SCART, AV-1 or S-Video terminals, the Sound Mode Selector button is not operative.

MUTE

STEREO

MONO

Note:

Page 23

Sound qualities are adjustable in this menu.

1. Press the MENU button to see the MAIN Menu.

2. Press the Cursor DOWN button to select «AUDIO ADJUSTMENTS».

3. Press the MENU button to see the SOUND Menu

SOUND Menu

4. Press the RED button to select «LOUDSPEAKERS» or press the GREEN button to select «HEADPHONES».

5. Press the Cursor UP / DOWN buttons

/ to select an option from the list:

For «LOUDSPEAKERS»: VOLUME, EQUALIZER, LOUDNESS, BALANCE or NORMALISE. For «HEADPHONES»: VOLUME, BASS, TREBLE, BALANCE or NORMALISE. The selected option will appear in white letters on a blue background.

6. Adjust the sound quality according to your preferences with the Cursor

LEFT / RIGHT buttons

/ .

«EQUALIZER» Menu

Select «EQUALIZER» to adjust the equalization. a) Press the Cursor LEFT / RIGHT buttons

/ to select:

120 Hz, 500 Hz, 1K Hz, 5 KHz or 10 KHz.

b) Press the Cursor UP / DOWN buttons

/ to Adjust.

The Equalizer adjustments are not operative for the headphones.

«LOUDNESS» mode

Select «LOUDNESS» to improve the sound quality [].

Press the Cursor LEFT / RIGHT buttons

/ to select:

Normal, Special or Off

The «LOUDNESS» modes are not operative for the headphones.

CHCHCH

Sound Setting Mode

 «LOUDNESS» increases the volume of low and high frequency signals according to the current volume setting. In «NORMAL» mode keeping the amplitude of the 1 KHz reference frequency constant. In «SPECIAL» mode keeping the amplitude of the 2 KHz reference frequency constant.

NORMALISE

BALANCE

LOUDNESS

EQUALIZER

VOLUME

➜

LOUDSPEAKERS

MAIN Menu

SOUND Menu «LOUDSPEAKERS»

«LOUDNESS» mode

EQUALIZER

LOUDSPEAKERS

OFF

VOLUME

LOUDNESS

BALANCE

NORMALISE

EQUALIZER

VOLUME

LOUDNESS

BALANCE

NORMALISE

120 500 1k 5k 10k

➜

«EQUALIZER» Menu



LOUDSPEAKERS

HEADPHONES

RED GREEN

NORMALISE

BALANCE

TREBLE

BASS

VOLUME

➜

HEADPHONES

SOUND Menu «HEADPHONES»



LOUDSPEAKERS

HEADPHONES

LOUDSPEAKERS HEADPHONES

RED GREEN

PICTURE

ADJUSTMENTS

AUDIO

ADJUSTMENTS

Note:

Page 24

«NORMALISE»

Select «NORMALISE» and press the MENU button to normalise

audio levels to default factory settings.

7. Press the Cursor DOWN button to see more options: «LOUDSPEAKERS» (Mode), «HEADPHONES» (Mode), «EFFECTS» and «SOUND IDENTIFICATION».

SOUND MODE

8. Press the Cursor UP / DOWN buttons

/ to select:

«LOUDSPEAKERS» or «HEADPHONES».

9. Press the Cursor LEFT / RIGHT buttons

/ to change the

sound mode, as indicated on page 21, in the -Sound Mode Selector- chapter.

«EFFECTS»

Select «EFFECTS» and press the Cursor LEFT / RIGHT buttons

/ to activate (ON) or deactivate (OFF) the spatial effect [].

«SOUND IDENTIFICATION»

Select «SOUND IDENTIFICATION» and press the Cursor LEFT /

RIGHT buttons

/ to activate (ON) or deactivate (OFF) the auto-

matic Identification of audio system of the current program [].

10. Press the MENU button to close the Menu.

CHCHCH

EFFECTS

HEADPHONES

STEREO

LOUDSPEAKERS

NORMALISE

BALANCE

LOUDNESS

EQUALIZER

VOLUME

➜

Press the MENU button to normalise...

LOUDSPEAKERS

«NORMALISE»

SOUND MODE

SOUND

IDENTIFICATION

EFFECTS

HEADPHONES

OFF

«EFFECTS»

 «EFFECTS»

EFFECT OFF: Normal sound without sound effect. EFFECT ON: the spatial effect depends on whether the feed is MONO or STEREO. If the source feed is MONO, it produces a “Pseudo Stereo” effect. If the source feed is STEREO, it produces a spatial effect, expanding the stereophonic image.

 «SOUND IDENTIFICATION»

IDENTIFICATION ON: The TV automatically identifies the received audio system MONO FM, STEREO or DUAL SIGNAL. IDENTIFICATION OFF: Disqualifies the automatic identification of the audio system and forces the sound into MONO FM. This mode can be convenient when the level of the signal received is extremely weak. This function is independent for every program. Note: the audio «EFFECTS» do not work with headphones.

SOUND

IDENTIFICATION

EFFECTS

«SOUND IDENTIFICATION»

Page 25

In this mode you can set the «ON-TIMER» an «OFF-TIMER», set the CHILD LOCK, view the all functions implemented in your TV set demonstration and set the POSTCODE.

1. Press the MENU button to see the MAIN Menu.

2. Press the Cursor DOWN button F to select «OTHER FUNC-

TIONS».

Press the MENU button to see the «OTHER FUNCTIONS» Menu.

«OTHER FUNCTIONS» Menu

4. Press the Cursor UP/DOWN buttons E/F to select an option

from the list: «ON TIMER», «OFF TIMER», «CHILD LOCK», «DEMO» or «POSTCODE». The selected item will appear on screen in white letters on a blue background.

«OTHER FUNCTIONS» Menu «ON TIMER»

The On-Timer is used to automatically switch on the TV set during the day. If necessary, repeat steps 1. to 4. to see the «ON TIMER» Menu.

5. Press the Cursor RIGHT button to select the «TIME» (current time) in white letters.

6. To programme the current Time: In order to be able to run this function, it is essential to adjust the current time. Automatic Time adjustment: If you are receiving a channel with Teletext, the Time is automatically synchronized with the Teletext clock.

Important: If a signal via satellite is being received, or if correct time cannot be obtained, the time will have to be adjusted manually. Manual Time adjustment: To adjust the time manually, this should be done with the 0 to 9 digit buttons.

7. Adjusting the «SWITCH ON» Time: select «SWITCH ON» in white letters with the Cursor RIGHT button and press the 0 * 9 digit buttons to adjust the desired switch on time.

The GREEN button is used to cancel the «SWITCH ON» function.

8. Press the MENU button to close the Menu.

9. Press the Stand-by button (æ TV) on the remote control to put the

TV into switch on Stand-by Mode. When the preset time is reached, the TV set turns ON automatically.

* As a safety precaution, in the case of nobody being home when the

television switches on automatically, the television will return to Stand-by Mode after 120 minutes; if it is to continue to run, any button on the remote control functions should be pressed.

In the event of a power cut, disconnection from the plug or television switch, all the data on the «ON TIMER» will be cancelled.

«OTHER FUNCTIONS» Menu «OFF TIMER»

The «OFF TIMER» automatically switches the TV set to standby mode after a predetermined period, (30, 60, 90 or 120 minutes). If necessary, repeat steps 1. to 4. to see the «OFF TIMER» Menu.

5. Pressing the Cursor RIGHT button , select the desired period in

white letters. Select «OFF» to disconnect off-timer.

6. Press the MENU button to close the Menu.

After the selected time has passed, the TV will turn itself off automatically, and switch to Stand-by mode.

The «OFF TIMER» data will be cancelled if you turn off the TV by the Standby button (æ TV) on the remote control or with the Main power button (®) on the TV set.

Features setting mode

MAIN Menu

GREEN

CANCEL

DEMO

CHILD LOCK

OFF TIMER

ON TIMER

TIME 08:30 SWITCH ON **:**

«OTHER FUNCTIONS» Menu «ON TIMER»

➜

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

AJUSTMENTS

PICTURE

ADJUSTMENTS

Note:

DEMO

CHILD LOCK

OFF TIMER

ON TIMER

OFF

120 Min.

90 Min. 60 Min. 30 Min.

«OTHER FUNCTIONS» Menu «OFF TIMER»

➜

Note:

Page 26

Child Lock (Channel Block)

You can lock a TV channel to prevent unsupervised TV viewing by following these procedures; the protection can apply to the television itself «LOCK ALL» or to specific programmes «LOCK PROGRAMME». With the CHILD LOCK function, you can also programme a time period during which the TV will be protected. (Your children cannot select the channel, which you locked).

1. Press the MENU button to see the MAIN Menu.

MAIN Menu

2. Press the Cursor DOWN button F to select «OTHER FUNCTIONS».

3. Press the MENU button to see the «OTHER FUNCTIONS» Menu.

«OTHER FUNCTIONS» Menu

4. Press the Cursor DOWN button F to select «CHILD LOCK» in white

letters on a blue background.

5. Press the MENU button to see the CHILD LOCK Menu.

CHILD LOCK Menu

6. Press the Cursor UP/DOWN buttons E/F to select an option from

the list: «LOCK ALL», «LOCK PROGRAMME» or «CLEAR LOCK» The selected item will appear on screen in a blue box.

CHILD LOCK Menu «LOCK ALL»

Select this option for protecting the access to the whole TV. If necessary, repeat steps 1. to 5. to see the CHILD LOCK Menu.

7. Press the Cursor RIGHT button to select the protection type (white letters):

Select «NONE»: To cancel the protection. Select «ALWAYS LOCKED»: The access to the TV will be protected

throughout the day. Select «START: **:**/STOP: **:**»: to block access to the TV during the desired period of time. Enter the hours and minutes using the numeric buttons 0 ~ 9 to set the starting and ending times of the lock period.

8. Press the GREEN button to memorize.

9. Press the MENU button to clear the on-screen display.

From this time forward, whenever the protection conditions are met, the screen will be blocked and the «LOCKED MODE» message will be displayed. Press any number key on the remote control to unlock the TV.

Since the “key” for unlocking the TV is the remote control, make sure you do not misplace it.

MAIN Menu

CHILD LOCK Menu «LOCK ALL»

MEMORIZE

NONE ALWAYS LOCKED START: **:** STOP: **:**

LOCK ALL

LOCK PROG.

CLEAR LOCK

GREEN

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

Note:

«OTHER FUNCTIONS» Menu

DEMO

CHILD LOCK

OFF TIMER

ON TIMER

Press the MENU button to enter the CHILD LOCK menu.

➜

Page 27

«LOCK PROGRAMME» menu

Select this option to protect the access to separate programmes.

1. Press the MENU button to clear the on-screen display.

2. Select the programme channel number you want to protect using

the 0 ~ 9 digit buttons or the channel selector E/F buttons.

3. Repeat steps 1. to 5. (Page 25) to see the CHILD LOCK Menu.

4. Press the Cursor DOWN button F to select «LOCK

PROGRAMME» (blue background).

5. Press the Cursor RIGHT button to select the protection type (white letters): Select «NONE»: To cancel the protection from the selected programme. Select «ALWAYS LOCKED»: To protect the access from the selected programme throughout the day. Select «START **:** / STOP **:**»: to block access to the selected channel during the desired period of time. Enter the hours and minutes using the number keys (0 ~ 9) set the starting and ending times of the lock period.

6. Press the GREEN button to memorize.

7. Press the MENU button to clear the on-screen display.

From this time forward, whenever the protection conditions are met, the screen will be blocked and the «LOCKED MODE» message will be displayed. Press any digit button to unlock the TV.

Since the “key” for unlocking the TV is the remote control, make sure you do not misplace it.

«CLEAR LOCK» menu

This option enables you to erase all the adjustments made to the CHILD-LOCK function. If necessary repeat steps 1. to 5. (Page 25) to see the CHILD LOCK Menu.

6. Press the Cursor UP button E to select «CLEAR LOCK».

7. Press the MENU button to confirm that you want to initialise

the CHILD LOCK system.

8. Press the MENU button to clear the on-screen display. Use the «CLEAR LOCK» to cancel any previously set CHILD

LOCK programmes to avoid malfunction when a new program is set.

«LOCK PROGRAMME» menu

MEMORIZE

NONE ALWAYS LOCKED START: **:** STOP: **:**

LOCK ALL

LOCK PROG.

CLEAR LOCK

GREEN

«CLEAR LOCK» menu

Press the MENU button to clear the CHILD LOCK system

LOCK ALL

LOCK PROG.

CLEAR LOCK

Notes: In order for the timed protection to function correctly, the internal TV clock must be set at the right time. To check the time setting, see section -Automatic or Manual time adjustment- on page 24.

Note:

The demonstration function allows you to see all the menus implemented in this TV set.

1. Press the MENU button to see the MAIN Menu.

2. Press the Cursor DOWN button F to select «OTHER FUNCTIONS».

3. Press the MENU button to see the «OTHER FUNCTIONS» Menu.

4. Press the Cursor DOWN button F to select «DEMO».

The selected item will appear on screen in white letters on a blue background.

5. Press the MENU button to begin the demonstration.

6. Press any button on remote control to exit this function when you wish.

DEMO

CHILD LOCK

OFF TIMER

ON TIMER

Press the MENU button to start the DEMO.

➜

Demo (Demonstration)

Page 28

This option allows you to set a code (Postcode), which will be displayed at TV switch on time. There is a Password (PSW) to change the code.

 SET PASSWORD AND POSTCODE

1. Press the MENU button to see the MAIN Menu.

MAIN Menu

2. Press the Cursor DOWN button F to select «OTHER

FUNCTIONS».

3. Press the MENU button to see the «OTHER FUNCTIONS»

Menu.

«OTHER FUNCTIONS» Menu

4. Press the Cursor UP button E to see the POSTCODE Menu.

POSTCODE Menu / ENTER PSW (Password)

It is indispensable to enter a Password in order to continue configuring the Postcode.

5. Enter the 4-digits using the number buttons 0 to 9 to set the

Password.

Password set (confirmation)

6. When the Password is first entered, the TV will ask for

confirmation. If this is the case, press the BLUE button . Then the "ENTER CODE" will appear on screen.

ENTER CODE (Postcode)

7. Press the Cursor UP/DOWN buttons E/F to set or change

the first letter/number. Letters A to Z of the alphabet, a blank space and the numbers 0 to 9 will appear sequentially.

8. Press the Cursor LEFT / RIGHT buttons

/ for changing the

position of the cursor (red background) and the E/F buttons for changing the letter/number. Repeat this action for other letters/numbers.

9. When you have finished the eighth letter/number, press the BLUE

button to confirm the Postcode.

Postcode set

10. When the Postcode has been set:

Press the GREEN button to activate the Postcode, which will be displayed at TV switch on time (for some seconds) or Press the RED button if you wish to deactivate the Postcode; in this case it will not be displayed.

About Postcode: If you memorize a «Post Code», in the events of lose or robbery of TV set and later recovery, you can identify your TV set by Postcode. Notes: As a precautionary measure, make a note of your «Password» and the «Postcode», and keep it in a familiar place (see last page of this manual).

IF YOU LOSE OR FORGET YOUR «PASSWORD», CONTACT YOUR TECHNICAL SERVICE OR DEALER.

ENTER CODE

- -------

Postcode Security

MAIN Menu

OTHER

FUNCTIONS

INSTALL

AND TUNE

«OTHER FUNCTIONS» Menu

ON TIMER

OFF TIMER

TIME 08:30 SWITCH ON **:**

POSTCODE Menu ENTER PSW (Password)

POSTCODE

INTRODUCE PASSWORD

ENTER PSW

- - - -

Pasword set (Confirmation)

POSTCODE

Press BLUE button to confirm

ENTER PSW

****

ENTER CODE (Postcode)

POSTCODE

Press BLUE button to confirm

ENTER CODE

********

Postcode set

POSTCODE

DEACTIVATE : RED BUTTON. ACTIVATE : GREEN BUTTON.

Page 29

 CHANGE PASSWORD AND/OR POSTCODE

If necessary, repeat steps 1. to 4. (page 27) to see the POSTCODE Menu.

POSTCODE Menu / ENTER PSW (Password)

It is indispensable to enter the current Password in order to change the Password and/or the Postcode.

5. Enter the current Password (4-digits) using the number buttons 0 to 9 to see the CHANGE PASSWORD Menu.

CHANGE PASSWORD Menu

If you do not intend to change the Password, press the GREEN button to continue and then please proceed to stage 9..

6. Press the RED button to change the Password

CHANGE PASSWORD Menu / ENTER PSW

7. Enter the 4-digits using the number buttons 0 to 9 to set the new

Password.

Password set (confirmation)

8. When the new Password is first entered, the TV will ask for

confirmation. If this is the case, press the BLUE button . Then the "ENTER CODE" will appear on screen.

ENTER CODE (Postcode)

9. Press the Cursor UP/DOWN buttons E/F to set or change

the first letter/number. Letters A to Z of the alphabet, a blank space and the numbers 0 to 9 will appear sequentially.

10. Press the Cursor LEFT / RIGHT buttons

/ for changing the

position of the cursor (red background) and the E/F buttons for changing the letter/number. Repeat this action for other letters/numbers.

11. When you have finished the eighth letter/number, press the BLUE button to confirm the Postcode.

Postcode set

12. When the Postcode has been set:

IF YOU LOSE OR FORGET YOUR «PASSWORD», CONTACT YOUR TECHNICAL SERVICE OR DEALER.

ENTER CODE

- -------

POSTCODE Menu ENTER PSW (Password)

POSTCODE

INTRODUCE PASSWORD

ENTER PSW

- - - -

Pasword set (Confirmation)

POSTCODE

Press BLUE button to confirm

ENTER PSW

****

ENTER CODE (Postcode)

POSTCODE

Press BLUE button to confirm

ENTER PSW

********

CHANGE PASSWORD Menu

POSTCODE

CHANGE PASSWORD Menu ENTER PSW

POSTCODE

INTRODUCE PASSWORD

ENTER PSW

- - - -

ENTER CODE

********

Postcode set

POSTCODE

DEACTIVATE : RED BUTTON. ACTIVATE : GREEN BUTTON.

RED BUTTON: CHANGE PASSWORD GREEN BUTTON: CONTINUE

Page 30

 To repeat the AUTO INST ALLATION

In this mode you can to do again the AUTO INSTALLATION (e.g.; after moving house). This function frees you of troublesome channel presetting procedures. Simply follow the instructions below to automatically store all onair and cable real channels into the programme channel memories.

1. Press the MENU button to see the MAIN Menu.

MAIN Menu

2. Press the Cursor DOWN button F to select «INSTALL AND

TUNE».

3. Press the MENU button to see the TUNE Menu.

TUNE Menu

4. Press the Cursor UP button E to select «AUTO-TUNE» (blue

box).

5. Press the MENU button to start the “AUTO INSTALLATION”.

The «AUTO INSTALLATION» menu will appear on your TV screen.

 The TV is ready to preset automatically all local channels for you.  If the TV is being used with a VCR, turn on the VCR and play back

a pre-recorded tape. The signal from the RF terminal of your VCR is assigned to a TV channel.

6. Now, press any button on the TV remote control to start Auto Channel Preset.

The TV will go through the following steps automatically and sequentially:

Automatic Channel Sorting System (ACSS): The TV set

SEARCHES FOR FREQUENCIES, memorises the channels found, and sorts them (according to technical criteria) from Pr-01 of the TV, to a maximum of 99 programmes.

This tuning process may take several minutes to perform.

Editing: When the TV has finished the automatic search, the «Stored programmes» menu will appears on the screen. If you wish to rename the channels or change the order, go on to

the section entitled -Stored programmes- (page 12). If you wish to go out of the menu, press the BLUE button .

Press MENU button

to Auto-tune

WARNING! All

pretuned channels

will be lost.

MAIN Menu

TUNE Menu

TV Channel Setting (Advanced)

INSTALL

AND TUNE

OTHER

FUNCTIONS

MODE

EDIT

AUTO-TUNE

Be sure the antenna cable is connected…

Press any button on

the handset to start.

SHARP

AUTOINSTALLATION

VÍDEO

«AUTO INSTALLATION»

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:



Edit this program



Go to sorting mode



Delete this program



Exit this menu

(red)

(green)

(yellow)

(blue)

«Stored programmes»

VCR

Note:

Searching

please wait

Pr 01

01 %

Searching

Page 31

 Manual Channel Preset (Preset using real channel numbers)

1. Select the programme channel number you want to preset with

the 0 ~ 9 digit buttons.

2. Press the MENU button to see the MAIN Menu.

MAIN Menu

3. Press the Cursor DOWN button F to select «INSTALL AND

TUNE».

4. Press the MENU button to see the TUNE Menu.

TUNE Menu «CHANNEL»

5. Press the Cursor RIGHT button to select (with white letters)

the Channel type: CH (Aerial) or CC (Cable).

6. Enter the real channel number you want to store with the 0 ~ 9

digit buttons (two digit entry only).

7. Press the GREEN button to memorize.

8. Press the MENU button to clear the on-screen display.

9. Repeat the above procedure for presetting other programme.

MEMORIZE

Pr 06 CH21

CH CC

MAIN Menu

TUNE Menu «CHANNEL»

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

GREEN

Page 32

 Manual Channel Preset (Preset using frequency tuning)

1. Select the programme channel number you want to preset with

the 0 ~ 9 digit buttons.

2. Press the MENU button to see the MAIN Menu.

MAIN Menu

3. Press the Cursor DOWN button F to select «INSTALL AND

TUNE».

4. Press the MENU button to see the TUNE Menu.

TUNE Menu «CHANNEL»

5. Press the Cursor RIGHT buttons to select (with white letters)

the Channel type: CH (Aerial) or CC (Cable).

6. Press the Cursor DOWN button F to select «SEARCH» (White

letters on a blue background).

TUNE Menu «SEARCH»

7. Press the Cursor LEFT/RIGHT buttons

/ to start preset.

The tuning sequence will stop when a signal is detected, if the signal is not the required channel press or to continue.

8. Press the GREEN button to memorize.

9. Press the MENU button to clear the on-screen display.

10. Repeat the above procedure for presetting other programme

channels.

MEMORIZE

Pr 06

CH21

MAIN Menu

TUNE Menu «SEARCH»

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

MEMORIZE

Pr 06

CH21

CH CC

TUNE Menu «CHANNEL»

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

GREEN

Page 33

 After preset has been performed

The following features are available for preset channels:

 Fine-tuning

When a preset programme channel is not exactly tuned, you can fine-tune the channel in this mode.

1. Select the programme channel number you want to tune using the

0 ~ 9 digit buttons.

2. Press the MENU button to see the MAIN Menu.

MAIN Menu

3. Press the Cursor DOWN button F to select «INSTALL AND

TUNE».

4. Press the MENU button to see the TUNE Menu.

TUNE Menu

5. Press the Cursor DOWN button F to select «F-TUNE» (FINE

TUNE) (White letters on a blue background).

FINE-TUNE Menu

6. Press and hold the Cursor LEFT or RIGHT buttons, until the

best tuning position is found, for the best picture and sound.

After Fine-tuning the programme number will turn from green to

yellow.

7. Press the GREEN button to memorize.

8. Press the MENU button to clear the on-screen display.

Repeat the above procedure for other programme channels as required.

 MODE

This feature allows you to select TV, VCR, SKIP. First follow the above

steps 1., 2., 3., and 4. The TUNE Menu will appear on screen.

5. Press the Cursor DOWN button F to select «MODE».

6. Press the Cursor RIGHT button to select (with white letters)

TV, VCR or SKIP: TV: If the TV signal is weak the image can shake.

In this case put it in TV mode.

VCR: In some case, the upper part of the picture may be distorted

when receiving signal from a VCR via RF terminal on the TV set. Selecting this option will help to reduce his effect.

SKIP:Allows you to SKIP channels you do not want to view when

using channels selector buttons E/F.

7. Press the GREEN button to memorize.

8. Press the MENU button to clear the on-screen display.

9. Repeat the above procedure for other programme channels as

required.

MEMORIZE

Pr 06

CH21

MEMORIZE

TV VCR SKIP

Pr 06

CH21

TUNE Menu

FINE-TUNE Menu

MODE

Pr 06

CH21

CH CC

GREEN

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

GREEN

MAIN Menu

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

MEMORIZE

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

Page 34

 Edit (Stored programmes)

This features allows you to delete, sort or input name for each one of the programmes with A ~ Z, 0 ~ 9 and hyphen.

1. Press the MENU button to see the MAIN Menu.

MAIN Menu

2. Press the Cursor UP button E to select «INSTALL AND

TUNE».

3. Press the MENU button to see the TUNE Menu.

TUNE Menu

4. Press the Cursor UP button E to select «EDIT» (blue box).

5. Press the MENU button to see the Stored programmes

«Stored programmes» menu

The «Stored programmes» menu will appear on screen with a list of the channels, which have been memorised with the available options:

a) Select programme to be edited  E/F. b) «Edit this program»  RED button . c) «Go to sorting mode»  GREEN button . d) «Delete this program»  YELLOW button . e) «Exit this menu»  BLUE button .

With these options, you will be able to organise the real channels (CH **) memorised in the TV programmes (Pr 01 ... Pr 99) and put them into your own preferred order.

For more explanation, please go on to the section entitled -Stored programmes- (page 12).

MAIN Menu

INSTALL

AND TUNE

OTHER

FUNCTIONS

AUDIO

ADJUSTMENTS

PICTURE

ADJUSTMENTS

CHANNEL

F-TUNE

MODE

EDIT

AUTO-TUNE

Press the MENU

button to enter...

Pr 06

CH21

TUNE Menu

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:



Edit this program



Go to sorting mode



Delete this program



Exit this menu

(red)

(green)

(yellow)

(blue)

«Stored programmes» menu

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

Press the MENU button to exit.

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

Insert the marked programme in the position you wish.

Press green button to finish.

Pr 01 CH21 BBC1 Pr 02 CH31 BBC2 Pr 03 CH41 ITV Pr 04 CH51 CH4 Pr 05 CH61 CNN Pr 06 - - - - - - - Pr 07 - - - - - - - Pr 08 - - - - - - - Pr 09 - - - - - - - Pr 10 - - - - - - - -

Stored programmes:

WARNING!

This programme

will be erased.

Press yellow button again

to confirm. Or press any other button

to cancel

«Edit this program» Edit name mode

«Go to sorting mode» Sorting mode

«Delete this program» Delete mode

Page 35

 TV/Video selector button

With this button you can select either source of input for the TV.

1. When the TV/VIDEO button is first pressed, the TV/Video

menu appears and TV mode changes to VIDEO mode.

The screen is displayed in the last VIDEO mode.

2. Press the corresponding COLOUR button to select one of

the input sources, as indicated in the diagram. If you press any COLOUR button during VIDEO mode, the

TV/Video menu will appears again.

Each time the corresponding COLOUR button is pressed, AV1 / S-VIDEO and FRONT / FRONT S-VIDEO change as indicated below.

GREEN button : AV1 S-VIDEO BLUE button : FRONT FRONT S-VIDEO The selected input will appear on the screen.

3. Press the MENU button to remove the menu from the screen or press the TV/VIDEO button and you will

exit the menu and VIDEO mode will change back to TV mode.

 CLOCK button

Press the button to display the current time on the screen.

That this function operates only if the station you are tuned to broadcasts a teletext signal.

 Headphone jack

The headphone jack is located behind the door. How to open the door: Put the finger in the lower part of the door

and press upward.

1. Press the MENU button to see the MAIN Menu.

2. Press the Cursor DOWN button F to select

«AUDIO ADJUSTMENTS»

3. Press the MENU button to see the SOUND Menu

4. Press the GREEN button to select «HEADPHONES VOLUME».

5. Turn down the volume with the Cursor LEFT button .

6. Insert the headphone plug all the way into the headphone jack as indicated on the drawing.

7. Adjust the headphone volume with the Cursor LEFT / RIGHT

/ buttons.

8. Press the MENU button to close the Menu.

The audio «EFFECTS» cannot be adjusted for the headphones.

 Sub-titles button h

This set has a quick access function for teletext subtitles, so that they can be selected by the press of one button. Simply press the h button on the remote control whilst in viewing mode (I.E. not teletext etc.) and subtitles will automatically be selected and displayed on the screen. To exit this mode, press h button again on the remote control.

The subtitle page is 888 by default. Maybe it is possible that a broadcaster doesn't use this page for subtitle. Please check and choose in Teletext mode the correct page manually.

Safety: In order to protect your ears, turn down the volume of the headphones before connecting them.

Other Features

TV/Video Menu

GREEN

BLUE

REED

DOOR

BEHIND THE DOOR

3.5 mm Ø Jack plug Earphone or Headphone Impedance 16~600 Ω

SCART

AV-1

S-VIDEO

FRONT

S-VIDEO

EURO-SCART

➜

Note:

Page 36

SHARP VCR can be operated using the TV remote control.

Channel selector buttons (VCR) CH

These buttons are used for changing channels and setting the timer.

Play button

Press this button to start playback.

Record button

Press this button to start recording. If the videocassette is protected against recording, it will be ejected.

Stop button

Press this button to stop playback or recording.

Operate button VCR

Press this button to turn your VCR on.

Fast forward/picture search forward and Rewind/picture search reverse buttons

Both these buttons have the following function:

Fast Forwarding and Rewinding

 To move through the cassette faster, press the STOP button to stop and then press the or button to fast forward or rewind the cassette.  Press the STOP button to stop fast forward or rewind.

Picture Search

 During playback, press the button for forward picture search, or the button for reverse search.  Press the PLAY button to resume normal playback. For further details, please refer to operation manual of your VCR.

VCR mode

Page 37

TELETEXT Mode

 What is Teletext?

Teletext is an information service, organized like a magazine, which is provided by some television stations in addition to regular television broadcasting. Your television receives special Teletext signals broadcast by a TV station, processes the information and displays it graphically on the screen. News, weather and sports information, stock exchange prices, program previews and closed captioning for the deaf are among the many services available through Teletext. Teletext information is organized much like a magazine: according to pages and sub-pages. The basic unit of displayed information is the page. A sub-page is one of a series of pages. Teletext reception is controlled by using the remote control. Refer to the appropriate button descriptions for operation of the Teletext functions.

 Teletext features

Depending on the TV programme, the Teletext pages are transmitted using different system. Your SHARP TV is adjusted to receive 2 Teletext systems, namely FLOF and LIST, which are automatically identified by the receiver. The user can easily identify them by the manner in which they appear on the screen.

TELETEXT

News Sports

Movie

Weather

FLOF

LIST

TELETEXT

100 200

300

400

RED GREEN

YELLOW

BLUE

RED GREEN

YELLOW

BLUE

 To switch ON and switch OFF the Teletext

1. Select the TV channel with Teletext information that you want to see.

2. Press the TEXT/MIX/PICTURE button a/b/Q to select Teletext mode.

3. Press the TEXT/MIX/PICTURE button a/b/Q two times to go out from Teletext mode.

a) Fast Page Selection

1. Select the appropriate programme channel.

2. Press the TEXT/MIX/PICTURE button a/b/Q to select Teletext mode.

3. To recall a page number displayed in the coloured brackets, simply press the corresponding coloured button.

b) 0-9 digi buttons

Enter a desired page number with the 0-9 digit buttons. (To select P.100: press 1, 0, 0).

c) Page selector (UP/DOWN)

You can sequentially select page numbers by pressing the Cursor UP/DOWN buttons E/F (channel selector buttons in the TV mode).

Basic TEXT features

Page 38

 TEXT/MIX/PICTURE button a/b/Q Every time this button is pressed, the Teletext is displayed in different modes, following the sequence described:

In TV mode: Press the TEXT/MIX/PICTURE button a/b/Q to enter the teletext mode. In teletext mode: Press the TEXT/MIX/PICTURE button a/b/Q to superimpose a teletext broadcast onto the

current TV programme screen (mixed mode). In mixed mode: Press the button again to return to the normal screen(TV mode).

 HALF PAGE button

Each time you press the button, the upper/lower half of the teletext page is magnified and displayed on the screen.

 HOLD button

Any teletext page or subpage can be held on the screen by pressing the HOLD button a. Press the button again to cancel the hold mode.

 REVEAL button

Press this button to reveal hidden information such as the answer to a quiz. Press the button again to hide the information.

Other TEXT features

 CLOCK button

In TV mode: When the TV signal with TEXT data is received, by pressing this button the real time information will appear on the top right area of the screen. In Teletext mode: When a selected Teletext page has hidden subpages or timed pages, these subpages can be seen in the following manner:

1. Press the CLOCK button

. Screen will show - + XXX / 0001

2. Using the RED button you can select the previous subpage, while with the YELLOW button you can move on to the following subpage. These two buttons are shown on the screen by the signs (—) and (+).

3. Wait until the subpage appears. You can use this button together with the display CANCEL button

. This means that you can view the main TV picture until the subpage has been found. The on screen TV icon in the top left side of the screen will show «TXT». When the subpage has been found, the screen will change to the subpage number. Press the TEXT/MIX/PICTURE button a/b/Q to view the subpage.

 CANCEL button

With this button Teletext information is cancelled and TV picture is restored. «TXT» Indication is shown on screen. In this position, the TV programme cannot be changed, being in Teletext/Cancelled mode. When a change takes place in the Teletext information, the upper time of the cancelled page or some other indication of special pages is shown on screen. To uncancel, press TEXT/MIX/PICTURE button a/b/Q and the whole teletext is shown.

This button can be used together with the clock button while awaiting subpages.

 RESET button

Press the reset button hto return back to index page, and go out from Teletext mode.

 LIST button (LIST)

Pressing this button you force the teletext to LIST Mode. It means that row 24 (bottom row of Teletext) will not have transmitter information, only the pages that user you have previously stored in the memory (More information on the next page -Teletext Page memory List-). Pressing «LIST» button again we go out from LIST Mode and system is going to be identified again (FLOF).

 INDEX button

Press the INDEX button jto return back to index page.

Note:

Page 39

Teletext Page memory List a) How to Operate Page Memory

Your TV has 40 teletext page number memories for fast recall of teletext information. In programme positions 1 through 9, four teletext page numbers can be stored in each position; a total of 36 pages. In programme positions 10 through 99, only one programme with 4 page numbers can be stored. If you try to store

more than 4 page numbers in a programme position between 10 and 99, the previously stored page numbers will be erased.

Select the programme channel number into which you want to store teletext page numbers.

1. Press the TEXT/MIX/PICTURE button a/b/Q to enter the teletext mode.

2. Press the «LIST» button to change from FLOF system to LIST mode.

3. Press a coloured button corresponding to the coloured brackets on the screen for page number storage.

4. Enter the teletext page number using the 0 ~ 9 digit buttons (enter three digits) or channel selector E/F

buttons.

5. Repeat steps 3. and 4. until the numbers for the desired pages have been entered.

6. Press the STORE

g button to memorize the page numbers you require. The symbol «STORE» appears on the

screen.

7. Press the TEXT/MIX/PICTURE button a/b/Q two times to go out from Teletext mode.

b) Fast Page Selection - LIST mode -

1. Select the appropriate programme channel.

2. Press the TEXT/MIX/PICTURE button a/b/Q to enter the teletext mode.

3. Press the «LIST» button to change from FLOF system to LIST mode.

4. To recall a page number displayed in the coloured brackets, simply press the corresponding coloured button.

5. Press the «LIST» button again to return to FLOF system.

Advanced TEXT operation - LIST mode -

(FLOF TELETEXT)

(LIST TELETEXT)

Press

LIST

and

YELLOW

buttons

Input

4, 2, 5

If you want to store,

press

g button

YELLOW

RED GREEN

YELLOW

BLUE

LIST

NEWS

SPORTS MOVIE WEATHER

Page 40

21-pin Euro-SCART and 21-pin Audio/V ideo

REAR TV 21-pin In/Out

1. 21-pin Audio/Video (AV-1) With

PAL/SECAM/NTSC/S-Video Input

2. 21-pin Euro SCART (RGB) With PAL/SECAM/NTSC Video Input

RF Input

3. Aerial terminal

21-pin Euro-SCART (RGB)

21-pin Audio/Video (AV-1) with S-Video Input

1. Audio right output 8. Audio-video control 15. Red input

2. Audio right input 9. Earth for green 16. Red/Green/Blue control

3. Audio left output 10. Not used 17. Earth for video

4. Common earth for audio 11. Green input 18. Earth for Red/Green/Blue control

5. Earth for blue 12. Not used 19. Video output

6. Audio left input 13. Earth for red 20. Video input

7. Blue input 14. Not used 21. Plug shield

1. Audio right output 8. Audio-video control 15. Chroma S-Video input

2. Audio right input 9. Earth 16. Not used

3. Audio left output 10. Not used 17. Earth for video

4. Common earth for audio 11. Not used 18. Earth

5. Earth 12. Not used 19. Video output

6. Audio left input 13. Earth 20. Video input / S-Video input

7. Not used 14. Not used 21. Plug shield

31 2

20 18 16 14 12 10 8 6 4 2

19 17 15 13 11 9 7 5 3 1

Page 41

If the fault cannot be corrected by using this guide, remove the mains plug from the wall socket and contact the dealer or supplier from whom it was purchased. Where this is not possible, please visit our web-site at www.sharp.co.uk/support. Customers without Internet access may telephone 08705 274277 [or (01) 676 0648 if telephoning form Ireland] during office hours. Certain replacement parts and accessories may be obtained from our Main Parts Distributor, who can be contacted on the following numbers: Willow Vale Electronics Ltd. 0121 766 5414 and 0161 205 7531 In the unlikely event of this equipment requiring any repair during the guarantee period, you will need to provide proof of the date of purchase to the repairing company. Please keep your invoice or Receipt, which is supplied at the time of purchasing.

Troubleshooting

PROBLEMS

PAGE

POSSIBLE CAUSES / REMEDIES

TV not plugged in Outlet power OFF Main power button of TV not ON Turn OFF using the Main Power button, then turn ON again after a minute Check batteries in the Remote Control Try a new channel to check for possible station trouble Aerial not connected to terminal at the back of the TV set

If outside aerial is used, check for broken wires Adjust COLOUR control

Try fine tuning to correct

Try a new channel to check for possible station trouble Aerial not connected to terminal at the back of the TV set If outside aerial is used, check for broken wires

Check for local interference

Try a new channel to check for possible station trouble Aerial not connected to terminal at the back of the TV set

If outside aerial is used, check for broken wires Check for local interference

Adjust COLOUR control Try fine tuning to correct

Check if the Brightness or Contrast setting in the picture setting mode might be all the way to the minus side

Try a new channel to check for possible station trouble

Check for local interference

Increase the volume

Try a new channel to check for possible station trouble TV not plugged in Outlet power OFF

Main power button of TV not ON Aerial not connected to terminal at the back of the TV set

If outside aerial is used, check for broken wires Turn OFF using the Main Power button, then turn ON again after a minute Check if the Brightness or Contrast setting in the picture setting mode might be all

the way to the minus side Increase the volume

Remote control does not work

13 13

Picture OK, sound poor

21, 22

Sound OK, picture poor

16 32

No picture or sound

14 10

No colour / Picture wear

Poor reception on some channels

21, 22

Page 42

General Specifications for Television Receiver

Models: 28KF-84H and 32KF-84H

1. Receiving Broadcast Standard CCIR TV Standard system PAL-I

2. Receiving Channel VHF: IRA - IRJ (CH01-CH09) UHF: I21 - I69 (CH21-CH69) CATV: S01 – S68 CC (Hyper band)

3. Receiving System Sound: FM MONO and DIGITAL STEREO NICAM

Colour System: PAL (SECAM and NTSC playback through the AV Inputs)

Field Frequency: 50/60 Hz Capability

4. Power Source 220V-240V AC 50 Hz

28KF-84H 32KF-84H

5. Power Consumption at 240V AC 50Hz 100 W 110 W

6. Power Consumption at (Stand-by) 1,5 W max. 1,5 W max.

7. Audio Output (mpo): 10 + 10 W 10 + 10 W

8. Dimensions (Approx.) Width: 824 m/m 930 m/m

Height: 495 m/m 558 m/m

Depth: 508 m/m 563 m/m

9. Viewing Area (diagonal measurement) 66 cm (28") 76 cm (32")

10. Weight (Approx.) 37 Kg 52 Kg

11. Speaker (2 pcs.) 6x13 cm. 6x13 cm.

12. Aerial Input Impedance UHF 75 ohm Unbalanced

13. Safety CE - MARK

14. EMC CE - MARK

15. Accessories & etc.

a) User Instruction Yes b) Quick Start Guide Yes c) Typical Connections Yes b) Remote Control Yes c) Battery 2 pcs.

● Auto Installation System (AIS)

● Automatic Channel Sorting System (ACSS)

● 99 Channel Programming System

● Cable and Hyperband

● Blue Back Noise Mute Function

● OSD System (On Screen Display)

● Flashback

● Simple Scan (100 Hz - Line Flicker Reduction)

● Digital Noise reduction

● Tint Control

● Picture rotation

● ECO mode

● Scope function

● Still mode

● Wide Mode Function

● Stereo (IGR) / Digital Stereo NICAM

● Graphic Equalizer

● ON-OFF Timer

● Child Lock System

● Teletext

● 21 pin Euro SCART Connector (RGB)

● 21 pin Audio/Video Connector (AV-1)

With S-Video Input

● NTSC playback AV Input

● Front Audio/Video Input Terminal

● Front S-Video Input Terminal

● Headphone Terminal

● Postcode Security

NOTE: THE “AV LINK” FUNCTION IS NOT AVAILABLE IN THIS MODEL

Page 43

Index

100 Hz Fast Menu ..................................................... 18

21-pin Audio/Video ................................................... 39

21-pin Euro-SCART (RGB) ....................................... 39

Accessories ................................................................ 3

After preset has been performed .............................. 32

Aerial Connections ...................................................... 6

Audio Adjustments ................................................... 21

Auto Channel Preset ........................................... 11, 29

Auto Installation System ........................................... 11

Automatic Channel Sorting System .................... 11, 29

Balance ..................................................................... 22

Bass .......................................................................... 22

Bilingual .................................................................... 21

Black Stretcher ......................................................... 17

Blue back off-timer ................................................... 13

Brightness ................................................................. 16

Clock button ....................................................... 34, 37

Colour ....................................................................... 16

Contents ..................................................................... 3

Contrast .................................................................... 16

Controls and Terminals ............................................... 5

Current time .............................................................. 24

Channel Selection ..................................................... 14

Child Lock (Channel Block) ...................................... 25

Delete (Programme) .................................................. 12

Demo (Demonstration) .............................................. 26

ECO mode .................................................................17

Edit (Programme) ...................................................... 12

Effects (Sound) .......................................................... 23

Equalizer ................................................................... 22

Features Setting Mode ............................................. 24

Fine tuning ................................................................ 32

FLOF (Teletext) ......................................................... 36

Front TV ...................................................................... 5

Headphone jack ........................................................ 34

Identification (Sound) ................................................ 23

LIST (Teletext) ............................................... 36, 37, 38

Loudness .................................................................. 22

Main power button .................................................... 13

Manual Channel Preset ....................................... 30, 31

Menu Structures ....................................................... 15

Mono ......................................................................... 21

Noise reductor .......................................................... 17

OFF-Timer ................................................................. 24

ON-Timer .................................................................. 24

Other Features .......................................................... 34

Picture Adjustments ................................................. 16

Picture Mode ............................................................ 18

Postcode Security .................................................... 27

Rear TV ....................................................................... 5

Remote Control buttons ............................................. 4

Remote Control Battery Installation ............................ 3

Rotation .................................................................... 17

Safety precaution ........................................................ 2

Scope Mode ............................................................. 18

Sharpness ................................................................. 16

SKIP .......................................................................... 32

Sorting (Programme) ................................................. 12

Sound mute .............................................................. 21

Sound Setting Mode ................................................. 22

Specifications ........................................................... 41

Stand-by button ........................................................ 13

Stereo ....................................................................... 21

Still Mode................................................................... 18

Stored programmes .................................................. 12

Sub-titles button ........................................................34

SVM ...........................................................................17

Switching on ............................................................. 13

Teletext ..................................................................... 36

Terms of guarantee ..................................................... 1

Tint control ................................................................ 16

Treble ........................................................................ 22

Troubleshooting ........................................................ 40

TV/Video selector ...................................................... 34

Typical connections .................................................... 6

Volume (Headphones) ........................................ 34, 22

Volume (Loudspeakers) ...................................... 21, 22

Wide Mode ............................................................... 19

Page 44

SHARP ELECTRÓNICA ESPAÑA, S. A.

SHARP ELECTRONICS (U.K.) LTD.

Sharp House, Thorp Road, Newton Heath,

Manchester M40 5BE

PRINTED IN SPAIN

TINS-A828WJN0 06/03

PASSWORD

POSTCODE SECURITY

TV SHARP 28/32KF-84H

✂