Sharp 32JW73H, 28JW73H User Manual

28JW-73H
32JW-73H

COLOUR TELEVISION

For easy installation

•

•

•

PRINTED IN SPAIN
TINS-7196BMN0
04/02

SHARPELECTRÓNICA

ESPAÑA, S.A.

SHARP ELECTRONICS

(U.K.) LTD.

Sharp House, Thorp Road, Newton Heath,

Manchester M40 5BE

5

NOW LET’S GET STARTED

INSTALLATION IS COMPLETE

PROBLEM

CHECK ITEM

PAGE

No picture or sound

Sound OK, poor picture

Picture OK, poor sound

Picture weak / No colour

Poor reception on some

channels

Remote control

does not work

TROUBLESHOOTING

6
9

6

19

6

16

16

19

20

6

16

14

6

6

9

9

3

If the TV does not react to Remote Control or hand buttons instructions, switch
ON/OFF and try again.

Fitting the batteries into the remote control
Connecting the aerial cable
Tuning the TV channels

Using this installation guide
should enable you to set up your
TV in less than 15 minutes - - -

- - - Refer to your operation
manual for more tips and advice

If problems persist, contact the SHARP Helpline (office hours only) on
tel: [phone] (or [phone] if telephoning from Ireland) and/or
WEB-SITE: www.sharp.co.uk/support

SAFETY WARNINGS

1 Select a well-ventilated location.

2 Avoid exposing the TV set to direct sunlight,

dust, heat sources, or moisture.

3 Do not place objects containing liquids or

candles on the top of the TV.

4 Never open the back cover.

5 Never insert objects into the TV.

6 Take care not to damage the power cord.

7 Keep the TV from strongly magnetic objects.

8 To prevent fire, never place any type of candle

or naked flames on the top or near the TV set.

Refer to the Operation Manual for:

Menu structures p.10
Channel selection p.15
Picture adjustments p.16
Wide mode p.17
Audio adjustments p.19
Timer settings (ON/OFF Timer) p.22
Child lock p.23
Postcode p.25
Teletext mode p.28

- TV not plugged in Outlet power OFF

- Main power button of TV not ON

- Aerial not connected to terminal at the
back of the TV set

- Check SOUND volume and SOUND mute

- Aerial not connected to terminal at the
back of the TV set

- Adjust COLOUR control

- Check if the Brightness or Contrast setting
in the picture adjustment mode might be
all the way to the minus side

- Increase the volume

- Check Audio levels

- Aerial not connected to terminal at the
back of the TV set

- Adjust COLOUR control

- Try fine tuning to correct

- Aerial not connected to terminal at the
back of the TV set

- Check for local interference

- Check in your home aerial installation

- TV not plugged in Outlet power OFF 6

- Main power button of TV not ON

- Turn OFF using the main power button,
then turn ON again after a minute.

- Check the batteries in the Remote Control

QUICK
START
GUIDE

1

2 The green power indicator will light.

3 The AUTO INSTALLATION message

will appear on your TV screen followed
by a diagram of typical connections.

Note:

If you need to repeat the AUTO
INSTALLATION, refer to the
relevant section on page 7 of the
operation manual.

The AUTO INSTALLATION function will tune all available
TV stations into your TV.
The TV is ready to preset automatically all local channels
for you.

Fitting the batteries

1.

2. 3.

1

2

Check List:

•

Is the TV connected to the mains?

•

Is the aerial connected to the TV?

3

4

If you do not intend to use your TV with
a VCR, proceed to stage 4.2.

1

2

Press any button on
the remote control to
start Auto Channel
Preset.

This tuning process may
take several minutes to
perform.

3 After searching is

finished, the channels
will be stored in the
following order.
Pr01 – BBC1,
Pr02 – BBC2,
Pr03 – ITV,
Pr04 – CH4,
Pr05 – CNN…

VCR

Remote Control

R-6 (“AA” size) Dry Batteries

Operation Manual

SHARP

AUTO INSTALLATION

Be sure the antenna cable. . .

Searching,
please wait.

Pr 01

TYPICAL CONNCETIONS

2

Aerial
(Not supplied)

Aerial Lead
(Not supplied)

30%

Stored programmes:

Pr01 CH21 BBC1
Pr02 CH31 BBC2
Pr03 CH41 ITV
Pr04 CH51 CH4
Pr05 CH61 CNN
Pr06 ----- - ----- ­Pr07 ----- - ----- ­Pr08 ----- - ----- ­Pr09 ----- - ----- ­Pr10 ----- - ----- -

Edit this program
Go to sorting mode
Delete this program
Exit this menu

(red)
(green)
(yellow)
(blue)

Back of TV

Back of TV

AUTO INSTALLATION

SUPPLIED ACCESORRIES

TYPICAL CONNECTIONS (Continued)

TURN ON TV FOR THE FIRST TIME

Press the main power button ( )
to start the AUTO INSTALLATION.

If the TV is used with a
VCR, turn on the VCR
and play back a
pre-recorded tape.

The Stored programmes menu will appear on screen and
you can change the order of the channels and change or
give the channels a four-letter name.

If you wish to rename the channels, or change the order,
refer to the page 8 chapter Stored programmes in the
operation manual.

Press the BLUE button to exit.

With your thumb
neil, pull up the
slit as shown.

Insert the two
batteries as shown.

Replace the cover.

Mains Socket Outlet
AC 220~240 V, 50 Hz

TV set

Power indicator

Main power button

A SCART lead (not supplied) is recommended for use with this TV, to
obtain the best communication between your TV and VCR, refer
to page 32 of the operation manual.

Press any button on
the handset to start.

28JW-73H
32JW-73H

COLOURTELEVISION

OPERATIONMANUAL

PRINTEDONENVIRONMENTALLYFRIENDLYPAPER