Microwave Drawer
INSTALLATION MANUAL
SPECIAL WARNING
INSTALLATION AND SERVICE MUST BE PERFORMED BY A QUALIFIED INSTALLER.
IMPORTANT: SAVE THIS INSTALLATION MANUAL FOR LOCAL ELECTRICAL INSPECTOR’S USE.
READ AND SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE.
CLEARANCES AND DIMENSIONS
For SAFETY CONSIDERATIONS do not install drawer in any combustible cabinetry, which is not in accord with the stated
clearances and dimensions on pages 2 and 3. See Figure 1 (for 24") or Figures 3 and 4 (for 30") .
UNPACKING YOUR MICROWAVE DRAWER
• Remove all packing
materials from inside
the Microwave Drawer.
DO NOT REMOVE
THE WAVEGUIDE
COV E R, w h ich is
lo c ated on the top
of t h e Micr owave
Drawer.
• Remove the feature
sticker, if there is one.
Check the drawer for
any damage, such as
misalig ned or bent
drawer, damaged drawer seals and sealing surfaces, broken
or loose Microwave Drawer guides and dents inside the cavity
or on the front side of the drawer. If there is any damage, do
not operate the Microwave Drawer and contact your dealer or
a SHARP AUTHORIZED SERVICER.
Sealing
surface
Waveguide
cover
Sealing
surface
Oven
cavity
IMPORTANT NOTES TO THE INSTALLER
• Read all of the Installation Manual before installing the
Microwave Drawer.
• Remove all packing material before connecting the electrical
supply.
• Observe all governing codes and ordinances.
• Be sure to leave these instructions with the consumer.
IMPORTANT NOTES TO THE CONSUMER
Keep this manual with your Operation Manual for future
reference.
• As when using any microwave oven generating heat, there are
certain safety precautions you should follow. These are listed
in the Operation Manual. Read all and follow carefully.
• Be sure your Microwave Drawer is installed and grounded
properly by a qualified installer or service technician.
IMPORTANT SAFETY INSTRUCTIONS
If the information in this manual is not followed
exactly, a fire or electrical shock may result that could cause
property damage, personal injury or death.
To reduce the risk of tipping, the Microwave
Drawer must be secured by a properly installed Anti-Tip
block.
• This Microwave Drawer must be electrically grounded in
accordance with local codes.
• Make sure the wall coverings and the cabinets around the
Microwave Drawer can withstand the heat generated by the
Microwave Drawer.
Never leave children alone or unattended in
the area where a Microwave Drawer is in use. Never leave the
drawer open when the microwave is unattended.
Stepping, leaning or sitting on the drawer
may result in serious injuries and can also cause damage to the
Microwave Drawer.
• Do not use the Microwave Drawer as a storage space.
This creates a potentially hazardous situation.
• Check that the time-of-day is in the display. If not, touch
Stop/Clear to prevent unintended use.
1
21 19/32"
23 3/8"
14 19/32"
1 13/16"
door thickness
15 13/32"
23 7/8"
15"
auto drawer
opening
1 23/32"
4 11/16"
CLEARANCES AND DIMENSIONS
36"
countertop
height
24"
cabinet min.
22 1/8"
opening
14 13/16"
opening
Allow
7/16"
overlap.
Allow 7/8"
overlap.
Allow 7/8"
overlap.
19" to top
of floor
4"
5"
Electrical outlet location
Anti-Tip
block
Floor must
support 100 lbs.
14 13/16"
to bottom
of Anti-Tip
block
3 1/2"
(6")
23 1/2"
min depth
Allow 3/16"
overlap.
• Dimensions that are shown in Figure 1 (for 24") or Figures
3 and 4 (for 30") must be used. Given dimensions provide
minimum clearance. Locate electrical outlet in the shaded
area in the upper left-hand corner of the cutout. See Figure 7.
• Contact surface must be solid and level. Pay special attention
to the floor on which the Microwave Drawer will sit. The
floor of the opening should be constructed of plywood
strong enough to support the weight of the oven (about 100
pounds).
24" MICROWAVE DRAWER MEASUREMENTS
• Check location where the Microwave Drawer will be
installed for proper electrical supply.
• Your oven can be built into a cabinet or wall by itself or
under a gas or electric wall oven.
• Be sure that the clearance of the floor between the wall oven
and the microwave drawer is a minimum of 2-inches.
• The microwave interior will easily accommodate a 9" x 13"
oblong dish or a bag of microwave popcorn.
Figure 1
Figures 1 and 2 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.
2
Figure 2
36"
countertop
height
30"
cabinet min.
28 7/16"
opening
14 3/4"
opening
Allow 1/4"
overlap.
Allow
7/16"
overlap.
Allow 3/4"
overlap.
Allow 3/4"
overlap.
4"
5"
Electrical outlet
location
Anti-Tip
block
Floor must
support
100 lbs.
14 13/16"
to bottom
of Anti-Tip
block
3 1/2"
6"
23 1/2"
min depth
19" to top of floor
(recommended)
84"
wall
cabinet
30"
cabinet min.
28 7/16"
opening
14 3/4"
opening
Allow 1/4"
overlap.
Allow
7/16"
overlap.
Allow 3/4"
overlap.
Allow 3/4"
overlap.
4"
5"
2" min.
Electrical outlet
location
Anti-Tip
block
Optional
wall oven
cutout
illustrated
in sketch
Floor must
support 100 lbs.
14 13/16"
to bottom
of Anti-Tip
block
3 1/2"
(6")
23 1/2"
min depth
19" to top of floor
(recommended)
30" MICROWAVE DRAWER MEASUREMENTS
28 1/8"
23 3/8"
14 3/4"
15 13/32"
30"
15"
auto drawer
opening
2"
4 11/16"
Anti-Tip
block
(6")
Figure 4
Figures 3, 4 and 5 contain many Microwave Drawer measurements
for reference when planning the drawer’s location.
Figure 3
ANTI-TIP BLOCK
NORMAL INSTALLATION STEPS
ANTI-TIP BLOCK INSTALLATION INSTRUCTIONS
To reduce the risk of tipping of the drawer, the Anti-Tip block
must be properly installed located 14 3/4-inches above the floor
on which the Microwave Drawer will sit. The 6-inch Anti-Tip
block must be provided by the installer. See Figures 1 and 6 (for
24") or Figures 3, 4 and 6 (for 30"). The Anti-Tip block prevents
serious injury that might result from spilled hot liquids.
If the Microwave Drawer is ever moved to a different location, the
Anti-Tip block must also be moved and installed. When installed
to the wall, make sure that the screws completely penetrate the
dry wall and are secured in wood or metal so that the block is
Figure 5
totally stable. When fastening, be sure that the screws do not
penetrate electrical wiring or plumbing.
Figure 6
3
Mounting
flange
ELECTRICAL OUTLET
4"
5"
Electrical outlet location
Anti-Tip
block
(6")
3-Prong plug
Grounding pin
3-Prong receptacle
Ground receptacle box
Permanent and Correct Installation
Grounding adapter
Ground receptacle box
Screw
Tab for grounding screw
Temporary Use
4 Screws
Parts supplied
DRAWER INSTALLATION
Figure 8A
Figure 7
The electrical requirements are a 120 volt 60 Hz, AC only,
15 amp. or more protected electrical supply. It is recommended
that a separate circuit serving only this appliance be provided.
The drawer is equipped with a 3-prong grounding plug. It must
be plugged into a wall receptacle that is properly installed and
grounded. Should you only have a 2-prong outlet, have a qualified
electrician install a correct wall receptacle.
Note: If you have any questions about the grounding or electrical
instructions, consult a qualified electrician or service person.
GROUNDING INSTRUCTIONS
This appliance must be grounded. The Microwave Drawer is
equipped with a cord having a grounding wire with a grounding
plug. It must be plugged into a wall receptacle that is properly
inst a lle d and grounded in accorda nce with the National
Electrical Code and local codes
and ordinances. In the event of
an electr ica l sho r t circuit,
ground i n g re d uc e s r i s k of
electric shock by providing an
escape wire for the electric
current.
1. Place the drawer adjacent to the wall or
cabinet opening. Plug the power supply cord
into the electrical outlet.
2. Carefully guide the drawer into the prepared
opening. Avoid pinching the cord between
the oven and the wall.
Figure 8B
3. Slide the drawer all the way until the
mounting flange is flush with the face of the cabinet. See
Figure 8A.
4. Open the drawer. Using the 4 holes on the drawer as a template,
pre drill the cabinet using a 1/16" bit. See Figure 8A.
5. Secure the drawer with the 4 screws supplied. See Figure 8B.
MODEL AND SERIAL NUMBER LOCATION
For models KB-6015K and KB-6002L
The name plate, including model and serial number, is located
on the faceplate behind the Microwave Drawer front.
For model KB-6014L
The name plate includes model and serial number. Open the
Microwave Drawer fully. The label is slightly beyond the back
wall of the microwave cavity facing up from the flat surface.
– Improper use
of the grounding plug can result
in a risk of electric shock. Do
not use an extension cord.
TI N S E B 4 6 1 M R R 0
CARE, CLEANING AND MAINTENANCE
Refer to the Operation Manual for cleaning instructions.
BEFORE YOU CALL FOR SERVICE
Read the BEFORE YOU CALL and operating instruction sections
in your Operation Manual. It may save you time and expense.
The list includes common occurrences that are not the result of
defective workmanship or materials in this range.
Refer to the warranty in your Operation Manual for Sharp’s
toll-free service number and address. Please call or write if you
have inquiries about your microwave product and/or need to
order parts.
SHARP ELECTRONICS CORPORATION
Sh arp Plaza, Ma hwah, New Jer sey 0 7430 -2135
1- 800- BE-SHARP (237-4277 )
4
PRIN TED IN USA
Loading...