Page 1
21L-FG1L
SERVICE MANUAL
S677221LFG1L
COLOUR TELEVISION
Chassis No. GA6
Chassis No. GA6
MODEL
In the interests of user safety (Required by safety regulations in some countries) the set should be restored to its original
condition and only parts indentical to those specified should be used.
CONTENTS
IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................................... 1-1
LOCATION OF USER’S CONTROL ...................................................................................................................... 2-1
INSTALLATION AND SERVICE INSTRUCTIONS ................................................................................................. 3-1
SERVICE MODE ..................................................................................................................................................... 4-1
ADJUSTMENT METHOD ........................................................................................................................................ 5-1
WAVEFORMS ......................................................................................................................................................... 6-1
CHASSIS LAYOUT ................................................................................................................................................. 7-1
BLOCK DIAGRAM .................................................................................................................................................. 8-1
DESCRIPTION OF SCHEMATIC DIAGRAM .......................................................................................................... 9-1
SCHEMATIC DIAGRAMS ......................................................................................................................................10-1
PRINTED WIRING BOARD ASSEMBLIES ........................................................................................................... 11-1
Parts Guide
21L-FG1L
Page
ELECTRICAL SPECIFICATIONS
POWER INPUT............................AC 110-220 V, 50/60 Hz
POWER RATING .....................................................85W
PICTURE SIZE .............................1,239 cm
CONVERGENCE ............................................. Magnetic
SWEEP DEFLECTION .................................. .. Magnetic
FOCUS ........................................................ Electrostatic
INTERMEDIATE FREQUENCIES
Picture IF Carrier Frequency ...................... 45.75 MHz
Sound IF Carrier Frequency ...................... 41.25 MHz
Color Sub-Carrier Frequency ......................42.17 MHz
(Nominal)
AUDIO POWER
OUTPUT RATING... ...................... 3.0 W(RMS) x 2pcs
2
(192sq inch)
SPEAKER
SIZE ........................................................ 2” X 3.5”, 2pcs
VOICE COIL IMPEDANCE .................16 ohm at 400 Hz
ANTENNA INPUT IMPEDANCE
VHF/UHF ........................................75 ohm Unbalanced
TUNING RANGES
VHF-Channels ................................................. 2 thru 13
UHF-Channels ................................................14 thru 69
CATV Channels ............................................. 1 thru 125
(EIA, Channel Plan U.S.A.)
Specifications are subject to change without
prior notice.
SHARP CORPORATION
This document has been published to be used for after
sales service only.
The contents are subject to change without notice.
Page 2
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 1. IMPORTANT SERVICE SAFETY PRECAUTION
[1] IMPORTANT SERVICE SAFETY PRECAUTION
IMPORTANT SERVICE SAFETY PRECAUTION
Service work should be performed only by qualified service technicians who are
thoroughly familiar with all safety checks and the servicing guidelines which follow:
WARNING
1. For continued safety, no modification of any circuit
should be attempted.
2. Disconnect AC power before servicing.
3. Semiconductor heat sinks are potential shock
hazards when the chassis is operating.
4. The chassis in this receiver has two ground systems
which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage
regulator circuit and the horizontal output circuit. The
isolated ground system is for the low B+ DC voltages
and the secondary circuit of the high voltage
transformer.
To prevent electrical shock use an isolation
transformer between the line cord and power
receptacle, when servicing this chassis.
SERVICING OF HIGH VOLTAGE SYSTEM
AND PICTURE TUBE
When servicing the high voltage system,
remove the static charge by connecting a
10k ohm resistor in series with an insulated
wire (such as a test probe) between the picture tube ground and the anode lead. (AC
line cord should be disconnected from AC
outlet.)
1. Picture tube in this receiver employs integral
implosion protection.
2. Replace with tube of the same type number for
continued safety.
3. Do not lift picture tube by the neck.
4. Handle the picture tube only when wearing
shatterproof goggles and after discharging the high
voltage anode completely.
X-RADIATION AND HIGH VOLTAGE LIMITS
1. Be sure all service personnel are aware of the
procedures and instructions covering X-radiation.
The only potential source of X-ray in current solid
state TV receivers is the picture tube. However, the
picture tube does not emit measurable X-Ray
radiation, if the high voltage is as specified in the
"High Voltage Check" instructions.
It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the
picture tube including the lead in the glass material.
The important precaution is to keep the high voltage
below the maximum level specified.
2. It is essential that servicemen have available at all
times an accurate high voltage meter.
The calibration of this meter should be checked
periodically.
3. High voltage should always be kept at the rated value
−no higher. Operation at higher voltages may cause
a failure of the picture tube or high voltage circuitry
and;also, under certain conditions, may produce
radiation in exceeding of desirable levels.
4. When the high voltage regulator is operating properly
there is no possibility of an X-radiation problem.
Every time a color chassis is serviced, the brightness
should be tested while monitoring the high voltage
with a meter to be certain that the high voltage does
not exceed the specified value and that it is regulating
correctly.
5. Do not use a picture tube other than that specified
or make unrecommended circuit modifications to the
high voltage circuitry.
6. When trouble shooting and taking test
measurements on a receiver with excessive high
voltage, avoid being unnecessarily close to the
receiver.
Do not operate the receiver longer than is necessary
to locate the cause of excessive voltage.
1 – 1
Page 3
IMPORTANT SERVICE SAFETY PRECAUTION
(Continued)
BEFORE RETURNING THE RECEIVER
(Fire & Shock Hazard)
Before returning the receiver to the user, perform
the following safety checks.
1. Inspect all lead dress to make certain that leads are
not pinched or that hardware is not lodged between
the chassis and other metal parts in the receiver.
2. Inspect all protective devices such as non-metallic
control knobs, insulating materials, cabinet backs,
adjustment and compartment covers or shields,
isolation resistor-capacity networks, mechanical
insulators, etc.
3. To be sure that no shock hazard exists, check for
leakage current in the following manner.
•
Plug the AC cord directly into a 110~220 volt AC
outlet, (Do not use an isolation transformer for this
test).
•
Using two clip leads, connect a 1.5k ohm, 10 watt
resistor paralleled by a 0.15µF capacitor in series
with all exposed metal cabinet parts and a known
earth ground, such as electrical conduit or electrical
ground connected to earth ground.
•
Use an AC voltmeter having with 5000 ohm per volt,
or higher, sensitivity to measure the AC voltage drop
across the resistor.
•
Connect the resistor connection to all exposed metal
parts having a return to the chassis (antenna, metal
cabinet, screw heads, knobs and control shafts,
escutcheon, etc.) and measure the AC voltage drop
across the resistor.
AII checks must be repeated with the AC line cord
plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the
purpose of completing these check.)
Any current measured must not exceed 0.5 milliamp.
Any measurements not within the limits outlined
above indicate of a potential shock hazard and
corrective action must be taken before returning the
instrument to the customer.
DVM
AC SCALE
1.5k ohm
10W
21L-FG1L
SAFETY NOTICE
Many electrical and mechanical parts in television
receivers have special safety-related characteristics.
These characteristics are often not evident from visual
inspection, nor can protection afforded by them be
necessarily increased by using replacement components
rated for higher voltage, wattage, etc.
Replacement parts which have these special safety
characteristics are identified in this manual; electrical
components having such features are identified by "
and shaded areas in the Replacement Parts Lists and
Schematic Diagrams.
TO EXPOSED
METAL PARTS
For continued protection, replacement parts must be
identical to those used in the original circuit. The use of
substitute replacement parts which do not have the same
safety characteristics as the factory recommended
replacement parts shown in this service manual, may
create shock, fire, X-radiation or other hazards.
"
CONNECT TO
KNOWN EARTH
GROUND
1 – 2
Page 4
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 2. LOCATION OF USER'S CONTROL
[1] LOCATION OF USER'S CONTROL
Quic k R eference C ontrol O peration
L oc ation of C ontrols
Front Pa nel
MAIN P O W E R
→
Press Stand by.
Press again Off.
ON Indicator
Power can be turned on
bytheremotecontrolby
pressing CH( ) or (
on the T V s et when the
indica tor is lit red.
ME NU .
Press Access es MAIN ME N U.
P ress a ga in E xits M AI N ME N U.
→
→
→
.
)
Rear Panel
VOLUME UP/DOWN
(+) Increases sound.
(–) Decreases sound.
SENSOR AREAFOR
REMOTE CONTROL
CHANNEL UP/DOWN
( ) S elects next higher cha nnel.
( ) Selects next lower channel.
ANTE NNA/CAB LE INP UT T E R MINAL
AV OUT T E R MINA LS
AV-1 IN T E R MIN AL S
2 – 1
Page 5
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 3. INSTALLATION AND SERVICE INSTRUCTIONS
[1] INSTALLATION AND SERVICE INSTRUCTIONS
INSTALLATION AND SERVICE INSTRUCTIONS
Note: (1) When performing any adjustments to resistor controls and transformers use non-metallic
screwdrivers or TV alignment tools.
(2) Before performing adjustments, the TV set must be on at least 15 minutes.
21L-FG1L
CIRCUIT PROTECTION
The receiver is protected by a 3.15A fuse (F701),
mounted on PWB-A, wired into one side of the AC
line input.
X-RADIATION PROTECTOR CIRCUIT TEST
After service has been performed on the horizontal
deflection system, high voltage system, B+ system,
test the X-Radiation protection circuit to ascertain
proper operation as follows:
1. Apply 110~220V AC using a variac transformer for
accurate input voltage.
2. Allow for warm up and adjust all customer controls
for normal picture and sound.
3. Receive a good local channel.
4. Connect a digital voltmeter to C602 +ve Terminal
and make sure that the voltmeter reads 20 ±1.1V.
5. Apply external 27V DC at C602 +VE Terminal by
using an
6. To reset the protector, unplug the AC cord and
remove external 27V DC at C602 +VE Terminal.
Now make sure that normal picture appears on the
screen.
7. If the operation of the horizontal oscillator does not
stop in step 5, the circuit must be repaired before the
set is returned to the customer.
external DC supply, TV must shut off.
HIGH VOLTAGE CHECK
High voltage is not adjustable but must be checked
to verify that the receiver is operating within safe
and efficient design limitations as specified checks
should be as follows:
1. Connect an accurate high voltage meter between
ground and anode of picture tube.
2. Operate receiver for at least 15 minutes at 110~220V
AC line voltage, with a strong air signal or a properly
tuned in test signal.
3. Enter the service mode and set Y-mute ON by using
Service R/C.
4. The voltage should be approximately 28KV (at zero
beam).
If a correct reading cannot be obtained, check circuitry
for malfunctioning components. After the voltage test,
make Y-mute off to the normal mode.
3 – 1
Page 6
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 4. SERVICE MODE
[1] SERVICE MODE
SERVICE MODE
1. Service mode is switched by SERVICE key, CH UP + VOL DOWN when reset.
2. Service mode is cancelled by SERVICE key during service mode.
3. Service mode can be switched to the following 4 modes via MENU key;
Adjustment mode
Setting mode
Check mode
Option mode
First Mode of Service when entering by SERVICE
key.
First Mode of Service when entering by 2 local keys.
4. During Service mode, AFT operation is prohibited. The setting data for PLL is always set to f
5. During Service mode, the following user data are set to default value and stored as last memory.
°
PICTURE/TINT/COLOR/BRIGHT/SHARP/COLOR TEMP.(FAV.COLOR)
BASS/TREBLE/BALANCE/MTS/FAO/SPEAKER/ENERGY SAVE/VIEW TIMER
6. During Service mode, OSD display for ON/OFF is toggled via [CH CALL] key.
At display OFF condition, if changing adjustment data, channel, input source, it remains display OFF.
At display OFF condition, if changing adjustment item, it returns to display ON.
7. During Service mode, the following operation are prohibited.
CLOSED CAPTION/No signal BLUE SCREEN/AUTO INPUT
8. During Service mode, sound is muted except when selecting the following items.
V23, M01~M06
data.
4 – 1
Page 7
Memory Map Data
Caution:
to get into the service mode, one of the ways is press direct key for service items.
There is three stage of Service Mode data
First stage data from V01 ~ M06
to go into second stage of service mode data, press MENU key
Second stage data from F01 ~ F101
to go into third stage of service mode data, press MENU key
Third stage data from O01 ~ O34
Below is the contents of these data
First Stage
Data Function Range Default Data
V01 CONTRAST 0~127 127
V02 TINT 0~127 64
V03 COLOR 0~127 64
V04 BRIGHT 0~255 128
V05 VIDEO-TONE 0~63 38
V06 V-SHIFT 0~7 1
V07 H-PHASE 0~31 20
V08 RF-DELAY 0~127 64
V09 V-SIZE 0~63 29
V10 V-SHIFT(OFFSET) -7~+7 0
V11 H-PHASE(OFFSET) -15~+15 0
V12 V-SIZE(OFFSET) -31~+31 0
V13 VIF-VCO 0~63 40
V14 R-CUTOFF 0~255 127
V15 G-CUTOFF 0~255 127
V16 B-CUTOFF 0~255 127
V17 R-DRIVE 0~127 64
V18 B-DRIVE 0~127 64
V19 COLOR 0~127 64
V20 BASEBAND-TINT 0~127 64
V21 CC-POS 0~255 32
V22 CUT OFF 0~2 0
V23 A-ATT 0~127 127
V24 H-VCO 0~7 4
V25 S-TRAPFINEADJ 0~15 0
V26 VS-CORRECTION 0~63 36
V27 VS-CORRECTION -13~+13 0
V28 V-LINEARITY 0~63 13
V29 V-LINEARITY -13~+13 0
M01 ATT (MTS) 0~15 9
M02 VCO (MTS) 0~63 32
M03 FILTER (MTS) 0~63 28
M04 WIDEBAND (MTS) 0~63 40
M05 SPECTRAL (MTS) 0~63 17
M06 VOL (MTS) 0~63 63
Auto Adjustment Item
1. H-VCO
2. RF-AGC
3. PIF-VCO
V LINEARITY OFFSET
MTS-WIDEBAND
MTS-SPECTRAL
SUB-VOL
SUB-PICTURE
SUB-TINT
SUB-BRIGHT
SUB-COLOR
Service Mode
SUB-SHARP
V-SHIFT
H-SHIFT
RF-AGC
V-SIZE
PIF-VCO
R-CUTOFF
G-CUTOFF
V-SHIFT50
H-SHIFT50
V-SIZE50
SCREEN CUT OFF
SUB-VOL
B-CUTOFF
R-DRIVE
B-DRIVE
SUB-COLOR(YUV)
SUB-TINT(YUV)
CC-POS
H-VCO
MTS-ATT
MTS-VCO
MTS-FILTER
S-TRAP
VS-CORRECT
VS-CORRECT OFFSET
VLINEARITY
21L-FG1L
4 – 2
Page 8
21L-FG1L
A
A
A
Y
Y
Y
Y
Y
Y
Y
A
A
A
A
A
Second Stage
Data Function Range Setting Data
F01 V-TONE 0/1 0
F02 V-TONE 0/1 0
F03 V-TONE 0/1 0
F04
F05 BS-OFF 0/1 0
F06
F07 VIDEO-TONE(OFFSET) -16~+16 0
F08 VIDEO-TONE(OFFSET) -16~+16 0
F09 VIDEO-TONE(OFFSET) -31~+31 0
F10 VIDEO-TONE(OFFSET) -31~+31 0
F11 EXTRGB-CLIP 0/1 0
F12 CONTRAST(OFFSET) 0~63 30
F13
F14 VIF-GAIN 0~7 4
F15 Y-DELA
F16 Y-DELA
F17 Y-DELA
F18 Y-DELA
F19 Y-DELA
F20 Y-DELA
F21 Y-DELA
F22 TINT(OFFSET) -32~+32 -1
F23 COLOR(OFFSET) -32~+32 +2
F24 COLOR(OFFSET) -31~+31 +24
F25 COLOR(OFFSET) -31~+31 0
F26 R-DRI(OFFSET) -32~+32 +8
F27 R-DRI(OFFSET) -32~+32 +3
F28 R-DRI(OFFSET) -32~+32 -2
F29 B-DRI(OFFSET) -32~+32 -18
F30 B-DRI(OFFSET) -32~+32 -8
F31 B-DRI(OFFSET) -32~+32 +6
F32 V-FREE 0/1 1
F33 GAMM
F34 H-FREE 0/1 0
F35 V.WINDOW 0/1 0
F36 V.WINDOW 0/1 1
F37 YSW-LPF 0/1 0
F38 BS-DISCHARGE 0~3 0
F39 BS-CHARGE 0~3 0
F40 S-SLICE DOWN 0~7 2
F41 S-SLICE DOWN 0~7 2
F42 S-SLICE DOWN 0~7 0
F43
F44 VSYNC-DET 0~3 3
F45 VSYNC-DET 0~3 2
F46 VSYNC-DET 0~3 0
F47
F48
F49
F50 FBP VTH 0/1 0
F51 FBP VTH 0/1 0
F52 FBP VTH 0/1 0
F53 C.CLIP LEVEL 0/1 0
F54 PSW 0/1 0
F55 VOL 0~63 58
F56 CHARGE PUMP 0/1 1
F57 CC LEVEL 0~31 0
F58 OSD POS 0~31 0
F59 OSD POS 1~55 38
F60 OSD POS 1~50 23
F61 COLOR +14
F62 TINT -32~+32 0
Service Mode
SHPG
SHPG-P
SHPG-N3
ABCL
BS
ABCL-G
SHP-AV
SHP-YUV
SHP-P
SHP-N3
RGB-CLIP
E-SAVE
FAO-VOL
PIF-G
Y-DELAY(TV)
Y-DELAY(AV-P)
Y-DELAY(TV-N3)
Y-DELAY(AV)
Y-DELAY(AV-P)
Y-DELAY(AV-N3)
Y-DELAY(YUV)
TINT-AV
COL-AV
COL-P
COL-N3
R-DRI(R2)
R-DRI( R)
R-DRI(B)
B-DRI(R2)
B-DRI( R)
B-DRI(B)
V-FREE
GAMMA
H-FREE
1W(TV)
1W(AV)
YLPF
BS-D
BS-C
SL(TV)
SL(AV)
SL(YUV)
AFC2
VD(TV)
VD(AV)
VD(YUV)
AS(TV)
AS(AV)
AS(YUV)
FBP(TV)
FBP(AV)
FBP(YUV)
C.CLIP LEVEL
PSW
FAO-VOL
CP
CC LEVEL
OSD POS-H
OSD POS-V50
OSD POS-V60
OFFSET-ADJ-COL
OFFSET-ADJ-TINT
BCL 0/1 0
BCL-G 0/1 0
-ATT 0~127 120
0~7 5
0~7 5
0~7 3
0~7 5
0~7 5
0~7 5
0~7 0
0~3 1
FC2-G 0/1 0
UTO-SLICE 0/1 1
UTO-SLICE 0/1 1
UTO-SLICE 0/1 0
-32~+32
4 – 3
Page 9
21L-FG1L
(
)
(
(
(
A
A
A
A
A
A
A
A
j
j
(
)
(
)
)
)
p
F63 BASEBAND-TINT -32~+32 0
F64 (SLOW MODE) 0/1 1
F65 R-CUT(OFFSET) -63~+63 0
F66 G-CUT(OFFSET) -63~+63 0
F67 B-CUT(OFFSET) -63~+63 0
F68 R-DRI(OFFSET) -63~+63 0
F69 B-DRI(OFFSET) -63~+63 0
F70 CONTRAST (OFFSET) -63~+63 0
F71 CONTRAST
F72 㧮㧾㧵㧳㧴㨀
F73 㧮㧾㧵㧳㧴㨀
F74 㧮㧾㧵㧳㧴㨀
F75 TRAP-FINE 0~3 2
F76 TRAP-FINE 0~3 2
F77 TRAP-FINE 0~3 2
F78 0~3
OFFSET-ADJ-TINT-YUV
WAIT MD TIME
R-CUT-YUV
G-CUT-YUV
B-CUT-YUV
R-DRI-YUV
B-DRI-YUV
CONTRAST OFFSET
CONTRAST YUV OFFSET
㧮㧾㧵㧳㧴㨀 OFFSET
BRIGHT AV2 OFFSET
BRIGHT YUV OFFSET
TRAP
TRAP-P
TRAP-N3
AFC1-Gain-TV
FC1-G
OFFSET
OFFSET)[0Ah
-63~+63
-63~+63
OFFSET)[0Ah -15~+15 +1
OFFSET)[0Ah -63~+63 0
FC1 Gain Up2
F79 0~3 3
AFC1-Gain-AV
FC1-G
FC1 Gain Up2
F80 0~3
AFC1-Gain-YUV
FC1-G
FC1 Gain Up2
F81 OM-Det 0/1 0
F82 BS-Gain 0/1 0
F83 C.ANGLE 0/1 0
F84 V AGC
F85 V STD DETOFF
F86 V STD DETOFF
F87 V STD DETOFF
F88 HALF-H KILLER
F89 V-DL Fine 0~3 0
F90 U-DL Fine 0~3 0
F91 CTI
F92 MCU VOUT
F93
F94
F95 Cr Pedestal Ad
F96 Cb Pedestal Ad
F97 SIF BPF WIDE 0~3 1
F98 COL-SYSTEM
OM-DET
㧮㧿㧙㧳㨍㨕㨚
C-ANGLE
V-AGC
V-STD-TV
V-STD-AV
V-STD-YUV
HALF-H KILLER
㨂㧙㧰㧸
㨁㧙㧰㧸
CTI Adj
MCUVOUT
AS-SPEED-DN
AS-SPEED-UP
CR-PEDESTEL-ADJ
CB-PEDESTEL-ADJ
SIF-BPF-WIDE
COL-SYSTEM
S-SPEED-DN
S-SPEED-UP
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
0/1
.
.
0~15
0~15
0: 11XX
1: 0011
AUTO
PAL-M
2: 0111(PAL-N
3: 0110(N358
F99 0/1 1
F100 SIF45 GAIN DOWN
F101 S-Tra
Pow-Storage
SIF45 GAIN DOWN
S-TRAP OFF
0/1
0/1
0
0
0
3
0
0
0
0
1
1
0
0
0
8
8
3
1
1
4 – 4
Page 10
21L-FG1L
Third stage
Data DATA = " 0"
O01 DEMO DISABLE ENABLE 1
O02 V-CHIP OP DISABLE ENABLE 0
O03 V-CHIP DISABLE ENABLE 0
O04 SPEAKER DISABLE ENABLE 1
O05 FAO DISABLE ENABLE 1
O06 P.REF DISABLE ENABLE 0
O07 UNIV+ DISABLE ENABLE 0
O08 VIEW TIMER DISABLE ENABLE 1
O09 EZ-SETUP AUTO PRESET 0
O10 POWER-ON DISABLE ENABLE 1
O11 FAV-COL COL-TEMP 1
O12 COMPONENT DISABLE ENABLE 0
O13 AV DISABLE ENABLE 1
O14 AV1 AV2 0
O15 MTS DISABLE ENABLE 1
O16 S-ADJ DISABLE ENABLE 1
O17 AUTO-OFF DISABLE ENABLE 1
O18 STANDBY MODE
O19 NO SET UP AUTO SET UP 1
O20 1
O21 AV3/S-IN DISABLE ENABLE 0
O22 COMB DISABLE ENABLE 0
O23 AUTO-INPUT DISABLE ENABLE 0
O24 CLOCK DISABLE ENABLE 0
O25 SEMEX MODEL SPC MODEL 1
O26 FLAT DISABLE ENABLE 1
O27 BASS BOOST DISABLE ENABLE 0
O28 DSE DISABLE ENABLE 0
O29 SRS DISABLE ENABLE 0
O30 WHITE-OUT DISABLE ENABLE 0
O31 Disable Enable 0
OPTION FUNCTION
DEMO
DOWNLOAD
V-CHIP
SPEAKER
FAO
P.PREF
UNIV+
VIEW TIMER
EZ-SETUP
* PON-CH
FAV-COL
COMPONENT
AV
AV2
MTS
TONE-CTRL
AUTO-OFF
LAST POWER
SETUP-FLAG
AV-FR
AV3/S-IN
COMB
AUTO-INPUT
CLOCK
LED
FLAT
BASS BOOST
DSE
SRS
WHITE-OUT
FORCE-COL
"0"=NO AV "1"=REAR "2"=FRONT "3"=REAR & FRONT
DATA =" 1"
POWER OFF CH
Setting Data
0
O32 Disable Enable 1
O33 ENGLISH 0
H-SYNC JUDGE
INIT-LANG 1
SPANISH 1
PORTUGUESE 2
O34 Range: 1 … 7LANG-SEL
Bit 0: Spanish
Bit 1: French
Bit 2: Portuguese
* POWER ON BY CH-UP / DOWN KEY.
4 – 5
1
Page 11
21L-FG1L
SELF ADJUSTMENT
H-VCO
1. When there is H-VCO self-adjustment key input for adjustment item H-VCO, self-adjustment is performed.
2. H-FREE(1chip) is set to 1.
3. H-OUT is set by intelligent monitor output.
4. IM input is set as TIM input.
5. H-VCO(1chip) data is changed so that the number of input pulse is 125 inside 8ms interval.
6. When adjustment completed, OSD display and H-VCO self-adjustment status data of EEPROM are updated.
7. H-FREE(1chip), intelligent monitor output and IM input mode are recovered.
RF-AGC
1. When there is RF-AGC self-adjustment key input for adjustment item RF-AGC, self-adjustment is performed.
2. AGC-OUT is set by intelligent monitor output.
3. IM input is set as AD input.
4. By decreasing RF-AGC (1chip) data from current RF-AGC adjustment value to 0, AFT input voltage becomes the
maximum setting value.
5. Increase RF-AGC(1chip) data, when AFT input voltage is at (max. 0.3V) point, adjustment is completed.
6. When adjustment completed, OSD display and RF-AGC self-adjustment status data of EEPROM are updated.
7. Intelligent monitor output and IM input mode are recovered.
PIF-VCO
1. When there is PIF-VCO self-adjustment key input for adjustment item PIF-VCO, self-adjustment is performed.
2. VIF-DEF(1chip) is set to 1.
3. AFC is set by intelligent monitor output.
4. IM input is set as AD input.
5. VIF-VCO(1chip) data is changed so that input voltage becomes 2.5V.
6. When adjustment completed, OSD display and PIF-VCO self-adjustment status data of EEPROM are updated.
7. VIF-DEF(1chip), intelligent monitor output and IM input mode are recovered.
4 – 6
Page 12
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 5. ADJUSTMENT METHOD
[1] ADJUSTMENT METHOD
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
㪩㪜㪝㪜㪩㩷㪘㪪㩷㪙㪜㪣㪦㪮
䋭
䋭
䋭
㪉㪈㪣㪄㪝㪞㪈㪣
OSD CHECKING
BUS OPTION
FUNCTION
FOR THIRD STAGE SERVICE DATA
O01 O02 O03 O04 O05 O06 O07 O08 O09 O10
DEMO DOWNLOAD V-CHIP SP FAO P.PREF UNIV+ VIEW EZ PON-CH
21L-FG1L
OPTION SET UP
STEP RANGE REFER AS BELOW
ADJUSTMENT 21L-FG1L 1 0 0 1 1 0 0 1 0 1
PROCEDURE
DEF
"0"= DISABLE
"1"=ENABLE
009 --> "0"= EZ-SETUP "1"= AUTO PRESET
BUS OPTION
FOR THIRD STAGE SERVICE DATA
HISTORY
OF REVISION
FUNCTION
O11 O12 O13 O14 O15 O16 O17 O18 O19 O20
FAV-COL COMP AV AV2 MTS TONE AUTO
Last Pow
SETUP AV-FR
21L-FG1L 1 0 1 0 1 1 1 0 1 1
FUNCTION
O21 O22 O23 O24 O25 O26 O27 O28 O29 O30
AV3 COMB A-IN CLOCK LED FLAT BASS DSE SRS WHITE
21L-FG1L 0 0 0 0 1 1 0 0 0 0
FUNCTION
O31 O32
FORCE COL
H-SYNC
21L-FG1L 0 1
O33
INITIAL LAN
1
O34
LANG-SEL
1
DEF O11 --> "0" =FAV-COL "1"= COL-TEMP
O33 --> "0"= ENGLISH "1"= SPANISH "2"=PORTUGUESE
O19--> "0"= NO SET UP "1" = AUTO SETUP
O20--> "0"=NO AV "1"=REAR "2"=FRONT "3"=REAR&FRONT
O25--> "0"= SEMEX SPEC "1" = SPC SPEC
O34--> "1" ENGLISH + SPANISH
SYMBOL
REVISED CONTENT .
5 – 1
Page 13
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
䋭
䋭
䋭
㪉㪈㪣㪄㪝㪞㪈㪣
OSD CHECKING
㪩㪜㪝㪜㪩㩷㪘㪪㩷㪙㪜㪣㪦㪮
DATA SETUP
FUNCTION
FOR FIRST AND SECOND STAGE SERVICE DATA
V05 V25 V26
SHARP S-TRAP VS COR
ADJUSTMENT 21L-FG1L 38 0 37
PROCEDURE
DEF
21L-FG1L
BUS SET UP
STEP RANGE REFER AS BELOW
V28
V-LIN
9
F14
PIF-G)
4
F17 F22
Y-DELAY (TY-N3)
3
TINT-AV
-1
HISTORY
OF REVISION
FUNCTION
21L-FG1L 1
F23
COLOR-AV
+2 5
F61
OFFSET ADJ COL
+14
F62 F58
2
DEF
SYMBOL
REVISED CONTENT .
F100
OSD POS-HOFFSET ADJ TINT SIF45 GAIN DOWN
5 – 2
Page 14
21L-FG1L
A
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
H-POSITION
STEP RANGEV07 0-31
I2C BUS CONTROL
OPTION SET UP, BUS SET UP,CRT-PURITY
US 4 CH LION HEAD (MONOSCOPE)
AC 220V, US MAGNETIC FIELD
CONFIRMATION BY CRT SCREEN
1.ADJUST THE V07 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B.
2.IF CANNOT MAKE IT TO A=B, ADJ FROM THE BEST POINT SO THAT B SLIDELY SMALLER
THAN A
B
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL
HISTORY
OFREVISION
SYMBOL
REVISED CONTENT .
5 – 3
Page 15
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
V-SIZE
V09 STEP RANGE 0~63
I2C CONTROL
OPTION SET UP, BUS SET UP,CRT PURITY, V-PHASE , +B ADJUST
US 4 CH LION HEAD
AC 220
CONFIRMATION BY CRT SCREEN
ADJUST THE V09 BUS DATA UNTILL THE OVERSCAN BECOME AS SPECIFIED BELOW.
CAUTION:- PLEASE AGING TV MORE THAN 10 MINUTES BEFORE ADJUSTMENT.
HISTORY
OFREVISION
[CHECKING SPEC]
OVERSCAN 10 ± 2.5%
SYMBOL
REVISED CONTENT .
5 – 4
Page 16
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTOROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
V-PHASE
V06 STEP RANGE 0-7
I2C CONTROL
OPTION SET UP, BUS SET UP, CRT PURITY
US 4 CH LION HEAD (MONOSCOPE PATTERN)
220 V, RF INPUT, ZERO MAGNETIC FIELD
CONFIRMATION ON CRT SCREEN
ADJUST V06 BUS DATA TO HAVE A MOST ACCEPTABLE VERTICAL POSITION.
THE MONOSCOPE PATTERN SHOULD BE BALANCE IN VERTICAL POSITION
NOTE: THE DATA FOR V06 LIMIT AT <= 04,EVEN POSITION NOT GOOD ENOUGH
HISTORY
OFREVISION
[CHECKING CONFIRMATION ]
SYMBOL
REVISED CONTENT .
5 – 5
Page 17
21L-FG1L
A
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
CLOSED CAPTION SET UP
V21 STEP RANGE 0 - 255
㪠㪉㪚㩷㪚㪦㪥㪫㪩㪦㪣
OPTION SET UP, BUS SET UP
US 4 CH LION HEAD
AC 220
CONFIRMATION ON CRT DISPLAY.
1)BY SELECTING THE V21, BOX BLK TEXT WILL BE APPEARED.
2)ADJUST THE V21 BUS DATA TO HAVE A BALANCE POSITION TO SPEC OF A=B.
TEXT BOX BLK
HISTORY
OFREVISION
B
[CHECKING SPEC]
LEFT AND RIGHT SYMMETRICAL THEN V21 DATA REDUCE 3 STEP.
SYMBOL
REVISED CONTENT .
5 – 6
Page 18
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
H-VCO
V24 STEP RANGE 0 - 7
㪠㪉㪚㩷㪚㪦㪥㪫㪩㪦㪣
OPTION SET UP, BUS SET UP
NO SIGNAL (RASTER) CONDITION
AC 220
IC 801 PIN 15
(MANUAL ADJ)
1)GO TO SERVICE MODE,
2)GO TO SERVICE DATA V24, ADJ UNTIL FREQ AS BELOW
(SELF ADJ)
1) GO TO SERVICE MODE, BY SELECTING THE SERVICE DATA V24
2) PRESS THE R/C TO OPERATE AUTO H-VCO, OSD APPEAR "OK" AT SCREEN
3) IF APPEAR "NG" PLS REPEAT STEP 2
HISTORY
OF REVISION
[CHECKING SPEC]
FREQ = 15.735 ± .02 KHz
SYMBOL
REVISED CONTENT .
5 – 7
Page 19
21L-FG1L
HISTORY
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
V13 STEP RANGE 0 - 63
㪠㪉㪚㩷㪚㪦㪥㪫㪩㪦㪣
OPTION SET UP, BUS SET UP
NO SIGNAL (RASTER) CONDITION
AC 220
CONFIRMATION ON CRT DISPLAY(AUTO), IC801 PIN 9 VOLTAGE (MANUAL).
21L-FG1L
PIF-VCO
(AT SELF ADJUSTMENT MODE)
1)GO INTO SERVICE MODE,BY SELECTING THE SERVICE DATA V13
2)PRESS THE R/C FOR AUTO PIF-VCO KEY, OSD APPEAR "OK" AT SCREEN
3)IF APPEAR "NG" PLS REPEAT STEP 2
(AT MANUAL ADJUSTMENT MODE)
ADJUST
PROCEDURE 2) ADJUST THE DATA UP/DOWN UNTIL IC801 PIN 9 VOLTAGE BECOME AS SPECIFIED BELOW
1)GO INTO SERVICE MODE, BY SELECTING THE SERVICE DATA V13
[CHECKING SPEC]
2.5 ± 0.5 V DC (CHECKING SPEC : 2.50 ± 1.5 V)
SYMBOL
REVISED CONTENT .
5 – 8
Page 20
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
RF-AGC
V 08 STEP RANGE 0-127
I2C CONTROL
OPTION SET UP, BUS SET UP
US10CH HALF COLOR BAR
RF INPUT
FIELD STRENGTH 53dB㱘㪭㩿㪝㪠㪯㪀㩷㩷㩷㩷㩷㩷
TUNER AGC TERMINAL (JA442 OR TP 201) OR CRT DISPLAY CONFIRMATION
(AT SELF ADJUSTMENT MODE)
1.GO TO SERVICE MODE
2.GO TO SERVICE DATA V08, PRESS R/C TO OPEARATE AUTO-AGC KEY AND CONFIRM THE OK
DISPLAY ON THE SCREEN .
3.IF APPEAR NG PLS REPEAT STEP 2 AGAIN.
(AT MANUAL ADJUSTMENT MODE)
1.ADJUST THE V08 BUS DATA UNTIL AGC TERMINAL VOLTAGE BECOME MAXIMUM, THEN
DROP 0.1V BELOW MAXIMUM VOLTAGE.
2. CHANGE THE ANTENNA INPUT SIGNAL TO 63~67 dBuV, AND MAKE SURE THERE IS NO NOISE
HISTORY
OFREVISION
3. CHANGE THE ANTENNA INPUT SIGNAL TO 90~95 dBuV TO BE SURE THAT THERE IS NO
CROSS MODULATION BEAT.
[VOLTAGE CONFIRMATION ]
MAX - 0.1V dc
SYMBOL
REVISED CONTENT .
5 – 9
Page 21
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
PURITY
STEP RANGE 0~255
OPTION SET UP, BUS SET UP,ROUGH CONVERGENCE
ONE COLOR (GREEN)
220 V
CONFIRMATION ON CRT DISPLAY.
1)SELECT THE ONE COLOR (GREEN) AND ADJUST BEAM CURRENT WITH SCREEN CONTROL
TO 700uA
2)DEGAUSS CRT WITH DEGAUSSING COIL
3)THE PURITY MAGNET MUST BE PREVIOUSLY SET AT THE "0" MAGNETIC FIELD AND
CONVERGENCE MUST BE ADJUSTED(ROUGH).
4)WITH PURITY MAGNET ADJUST CENTER TO RANK "A".
5)ADJUST DYNAMIC PURITY BY MOVING DY BACK AND FORTH TO RANK "A". (OPTIMUM POINT)
6)TIGHTEN SCREW OF DY
7)APPLY THE ADJUSTMENT AFTER AGING MORE THAN 30 MINUTES.
HISTORY
OFREVISION
[CAUTION POINT ]
SPEC:(L),(R)
CPTM CRT = INSIDE 20 +/- 10um
OTHER CRT = INSIDE 0 +/- 10um
SYMBOL
REVISED CONTENT .
5 – 10
Page 22
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SCREEN
V14,V15,V16 STEP RANGE 0~255
I2C CONTROL
OPTION SET UP, BUS SET UP
US-4CH LION HEAD
220 V
CONFIRMATION ON CRT DISPLAY.
1) IN SERVICE MODE, SET V04 TO 127 AND V14&V15&V16 TO 127; V17&V18 TO 64 , GET IN YMUTE BY R/C AND SET V22 TO "1", PICTURE APPEAR IN CUT-OFF CONDITION
2)ADJUST THE SCREEN SO THAT CUT-OFF LINE APPEAR IN LOW BRIGHT, THEN JUDGE THAT
WHETHER THE CUT-OFF LINE APPEAR IN RED OR GREEN OR BLUE COLOR, IN THIS CONDITION
V14= R-CUTOFF,V15=G-CUTOFF,V16=B-CUTOFF, FIX THE DATA OF THE COLOR APPEAR IN CUTOFF LINE AND USE R/C TO ADJUST THE OTHER TWO CUT-OFF DATA SO THAT CUT-OFF LINE
COLOR BECOME WHITE.
3)TURN THE SCREEN VR OF FBT SO THAT CUT-OFF LINE JUST DISAPPEAR AND USE R/C TO
SET V22 TO "0", NEXT DISABLE THE Y-MUTE SO THAT PICTURE APPEAR IN NORMAL MODE.
HISTORY
OFREVISION
[VOLTAGE CONFIRMATION ]
SYMBOL
REVISED CONTENT .
5 – 11
Page 23
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
WHITE BALANCE
V17,V18,V14,V15,V16 STEP RANGE 0-127, 0~255
I2C BUS CONTROL
OPTION SET UP, BUS SET UP, SCREEN
23CH 50IRE WINDOW PATTERN
220 V
CRT SCREEN DISPLAY .
1)WHITE (HIGH BEAM)
FIRST LET THE GUN POINT AT BLACK POSITION (AS DRAWING ATTACH), ADJ V04
UNTIL BRIGHTNESS Y BECOME 5 cd/m2, THEN LET THE GUN POINT AT WHITE
POSITION (AS DRAWING ATTACH),ADJUST VO1 UNTIL BRIGHTNESS Y BECOME 150
cd/m2, ADJUST THE BUS DATA OF V17(R DRIVE),V18(B DRIVE) UNTLL THE AXIS OF
COLOUR TEMPERATURE BECOME X=0.273,Y=0.280
2)BLACK (LOW BEAM)
LET THE GUN POINT AT BLACK POSITION, IF THE VALUE SHIFTED AWAY FROM THE
DATA ADJUSTED IN STEP 1), ADJUST AGAIN THE TWO SERVICE DATA WHICH HAVE
CHOSEN AT SCREEN ADJUST SO THAT TO OBTAIN THE SIMILAR AXIS AS ABOVE.
*WARNING: DO NOT DISTURB THE MINI STEP GUN DATA DURING THIS ADJUSTMENT.
**REPEAT STEP 1),2) TO GET A REGULATED POSITION.
.
HISTORY
OFREVISION
WHITE
[CHECKING CONFIRMATION ]
X=0.273,Y=0.280 (11,600° K+1 MPCD)
SYMBOL
REVISED CONTENT .
US14
BLACK
5 – 12
Page 24
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SUB-BRIGHT
V04 STEP RANGE 0-255
I2C CONTROL
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE
WINDOW PATTERN
220 V
CRT SCREEN DISPLAY .
1)LET THE GUN POINT AT BLACK POSITION(AS ATTACH DRAWING), ADJUST V04 BUS DATA
UNTILL BRIGHTNESS Y = 0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
HISTORY
OFREVISION
BLACK
[VOLTAGER CONFIRMATION ]
BRIGHTNESS Y = 0.5 cd/m2, THEN STEP DOWN MORE 4 STEP
SYMBOL
REVISED CONTENT .
US14
5 – 13
Page 25
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SUB-PICTURE
V01 STEP RANGE 0-127
I2C BUS CONTROL
OPTION SET UP, BUS SET UP, SCREEN, WHITE BALANCE, SUB-BRIGHTNESS
WINDOW PATTERN
220 V
CRT SCREEN DISPLAY
1) LET THE GUN POINT AT WHITE POSITION (AS ATTACH DRAWING), ADJUST V01 BUS DATA
UNTILL BRIGHTNESS Y = 150 cd/m2.
NOTE: ALLOWABLE DATA FOR V01 IS >= 90, EVEN Y CAN'T MATCH THE SPEC
HISTORY
OFREVISION
WHITE
[VOLTAGE CONFIRMATION ]
BRIGHTNESS Y = 150 cd/m2
SYMBOL
REVISED CONTENT .
US14
5 – 14
Page 26
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SUB-TINT
V02 STEP RANGE 0-127
I2C CONTROL
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
US 10 CH HALF COLOR BAR PATTERN
220 V
B-AMP TR BASE (JA410)
CONFIRRM WITH OSCILLOSCOPE
1)GET IN Y-MUTE FUNCTION BY R/C .
2)ADJUST THE V02 BUS DATA TO GET A WAVEFORM AS BELOW.
3) DISABLE THE Y-MUTE
B-AMP BASE (TP 47B)MUST BE IN
STEPPING LEVEL
HISTORY
OFREVISION
[CONFIRMATION ]
SYMBOL
REVISED CONTENT .
5 – 15
Page 27
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SUB-COLOR
V03 STEP RANGE 0-127
I2C BUS CONTROL
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC, SUB-PICT, SUB-TNT
US 10 CH HALF COLOR BAR PATTERN
220 V
R-AMP TR BASE (JA401)
CONFIRM WITH OSCILLOSCOPE
1)SET THE V03 BUS DATA TO GET A WAVEFORM AS BELOW
2)THIS WAVEFORM SHOWS THAT THE 75% WHITE & RED PORTIONS OF COLOR BAR BE AT THE
SAME LEVEL
Cy G
HISTORY
OFREVISION
Y
W
[CHECKING CONFIRMATION ]
SYMBOL
REVISED CONTENT .
100% WHITE
Mg R B
5 – 16
Page 28
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
X-RAY PROTECTION OPERATING CONFIRMATION
䋭
䋭
AFTER ALL ADJUSTMENT FINISHED.
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AC 220V, RF INPUT
CONFIRMATION BY THE CRT
SET THE USER CONTROL TO SHIPMENT POSITION.
[VOLTAGE CONFIRMATION]
CHECK THE VOLTAGE OF C602 +VE TERMINAL AS SPECIFIED BELOW.
[OPERATION CONFIRMATION]
SUPPLY THE DC VOLTAGE TO C602 +VE TERMINAL AND MAKE SURE THE PROTECTOR IS
FUNCTIONED , HORIZONTAL OSCILATION STOP AND PICTURE DISAPPEAR.
[RECOVER INFORMATION]
PULL OUT THE AC CORD .
STEP RANGE
䋭
HISTORY
OFREVISION
[CAUTION]
FROM THE RECOVER CONFIRMATION MENTIONED ABOVE,THE AC CODE MUST BE PULLED
OUT AT LEAST 4 SECOND BEFORE PLUGGING IN AGAIN. (IN ORDER TO MAKE SURE THE 㱘COM HAS BEEN RESET.)
[VOLTAGE COMFIRMATION]
TP VOLTAGE OPERATION VOLTAGE
26 ± 1.1V DC 27V
SYMBOL
㪤㪦㪛㪜㪣
21L-FG1L
REVISED CONTENT .
5 – 17
Page 29
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTOROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
HIGH VOLTAGE
䋭
䋭
AFTER ALL ADJUSTMENT FINISHED.
US 4 CH LION HEAD (MONOSCOPE PATTERN)
AC 220V, RF INPUT
CRT ANODE VOLTAGE
SET THE USER CONTROL TO SHIPMENT SETTING POSITION.PUSH ON Y - MUTE BY R/C
CONFIRM THE VOLTAGE OF CRT ANODE BY HIGH VOLTAGE METER AND MAKE SURE THE
READING IS AS BELOW.
STEP RANGE
䋭
HISTORY
OFREVISION
MODEL
㪉㪈㪣㪄㪝㪞㪈㪣
HIGH VOLTAGE
BELOW 30kV
[CAUTION POINT ]
USE ELECTROSTATIC HI-VOLTAGE METER AND FOLLOW THE UL / DHHS STANDARD TO MAKE
CORRECTION AND CONTROL.
SYMBOL
REVISED CONTENT .
5 – 18
Page 30
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
MS LEVEL ADJUSTMENT
㪤㪇㪈
㪠㪉㪚㩷㪙㪬㪪㩷㪚㪦㪥㪫㪩㪦㪣
OPTION SET UP, BUS SET UP, VCO ADJ, RF-AGC
MONORAL SIGNAL
(400HZ 100% MODULATION)
AC 220V, RF INPUT
IC 3001 39 PIN
1) SET THE SOUND VOLUME CONTROL MORE THAN 1.
2) ADJUST BUS DATA OF M01 UNTIL THE VOLTAGE OF 39 PIN BECOME AS SPECIFIED BELOW.
STEP RANGE
㪇㪄㪈㪌
HISTORY
OFREVISION
[CONFIRMATION VOLTAGE]
530m (+ 18m , -35m ) Vrms
SYMBOL
REVISED CONTENT .
5 – 19
Page 31
21L-FG1L
MODEL NAME
ADJUSTMENT
ITEM
ADJUSTMENT
POSITION
CONTOROL
PRE-ADJUST
REQUIREMENT
CONTENT
INPUT
CONDITION
OUTPUT
ADJUSTMENT
PROCEDURE
21L-FG1L
SEPARATION ADJUSTMENT
㪤㪇㪋㪃㪤㪇㪌
㪠㪉㪚㩷㪙㪬㪪㩷㪚㪦㪥㪫㪩㪦㪣
㪦㪧㪫㪠㪦㪥㩷㪪㪜㪫㩷㪬㪧㪃㩷㪙㪬㪪㩷㪪㪜㪫㩷㪬㪧㪃㩷㪭㪚㪦㩷㪘㪛㪡㪃㩷㪩㪝㪄㪘㪞㪚㪃㩷㪤㪪㪄㪣㪜㪭㪜㪣㪃
STEREO SIGNAL SIGNAL 1 : MODULATION 30%, L-CH ONLY, NR-ON, 300Hz
SIGNAL 2 : MODULATION 30%, L-CH ONLY, NR-ON, 3kHz
RF INPUT
IC 3001 39 PIN
1) INPUT SIGNAL 1, ADJUST BUS DATA OF M04 UNTIL THE OF 39 PIN BECOME MINIMUM LEVEL.
2) INPUT SIGNAL 2, ADJUST BUS DATA OF M05 UNTIL THE AC VOLTAGE OF 39 PIN BECOME
MINIMUM LEVEL.
3) REPEAT STEP 1) AND 2).
SET THE SOUND VOLUME TO MAXIMUM THEN MAKE SURE THE READING FROM THE SPEAKER
TERMINAL MUST BE OVER THE SPEC AS SPECIFIED BELOW.
STEP RANGE
㪇㪄㪍㪊
HISTORY
OFREVISION
[CONFIRMATION ]
OVER 25 dB
SYMBOL
REVISED CONTENT .
(CHECKING SPEC : OVER 20 dB)
5 – 20
Page 32
21L-FG1L
:$9()2506
+RUL]5DWH
9SS
+RUL]5DWH
9SS
+RUL]5DWH
9SS
+RUL]5DWH
9SS
9HUW5DWH
9SS
+RUL]5DWH
+RUL]5DWH
9SS
+RUL]5DWH
9SS
9SS
9SS
9SS
9SS
9SS
9HUW5DWH
9SS
+RUL]5DWH
9HUW5DWH
+RUL]5DWH
9SS
9HUW5DWH
+RUL]5DWH
9SS
+RUL]5DWH
9SS
+RUL]5DWH
9SS
9SS
+RUL]5DWH
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 6. WAVEFORMS
[1] WAVEFORMS
6 – 1
Page 33
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 7. CHASSIS LAYOUT
[1] CHASSIS LAYOUT
H
G
F
21L-FG1L
21L-FG1L
E
D
C
B
A
1
2
3
54
6
7
8
109
7 – 1
Page 34
21L-FG1L
A
C
B
D
E
F
G
H
2
109
8
7
6
54
3
1
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 8. BLOCK DIAGRAM
[1] BLOCK DIAGRAM: MAIN UNIT
8 – 1
Page 35
21L-FG1L
1110
12
13
14
15
16
17
18
19
8 – 2
Page 36
21L-FG1L
[2] BLOCK DIAGRAM: CRT UNIT
+
21L-FG1L
*
)
(
'
&
%
$
8 – 3
Page 37
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 9. DESCRIPTION OF SCHEMATIC DIAGRAM
[1] DESCRIPTION OF SCHEMATIC DIAGRAM
DESCRIPTION OF SCHEMATIC DIAGRAM
21L-FG1L
NOTES:
1. The unit of resistance "ohm" is omitted.
Ω
=1000Ω,M=MΩ)
(K=k
2. All resistors are 1/16 watt, unless otherwise noted.
3. All capacitors are
µµ
(P=pF=
4. (G) indicates
indicates line isolated ground.
5.
VOLTAGE MEASUREMENT CONDITIONS:
1. All DC voltages are measured with DVM connected
between points indicated and chassis ground, line
voltage set at 120V AC and all controls set for normal
picture unless otherwise indicated.
2. All voltages measured with 1000
signal.
F)
µ
F, unless otherwise noted.
±
2% tolerance may be used.
µ
V B & W or Color
WAVEFORM MEASUREMENT CONDITIONS:
1.
Photographs taken on a standard gated color bar
signal, the tint setting adjusted for proper color. The
wave shapes at the red, green and blue cathodes of
the picture tube depend on the tint, color level and
picture control.
2.
indicates waveform check points (See chart,
waveforms are measured from point indicated to
chassis ground.)
AND SHADED ( ) COMPONENTS
= SAFETY RELATED PARTS.
MARK= X-RAY RELATED PARTS.
DRGANNES MARQUES ET HACHRES ( ):
PIECES RELATIVES A LA SECURITE.
MARQUE : PIECS RELATIVE AUX RAYONS X.
This circuit diagram is a standard one, printed circuits
may be subject to change for product improvement
without prior notice.
9 – 1
Page 38
21L-FG1L
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 10. SCHEMATIC DIAGRAMS
[1] SCHEMATIC DIAGRAM: MAIN UNIT
H
G
21L-FG1L
F
E
D
C
B
A
1
2 109
3
54
6
7
8
10 – 1
Page 39
21L-FG1L
1110
12
13
14
15
16
17
18
19
10 – 2
Page 40
21L-FG1L
[2] SCHEMATIC DIAGRAM: CRT UNIT
H
G
21L-FG1L
F
E
D
C
B
A
1
2
3
54
6
7
8
109
10 – 3
Page 41
TV21L-FG1LService Manual21L-FG1LMarketE
CHAPTER 11. PRINTED WIRING BOARD ASSEMBLIES
[1] PWB-A: MAIN UNIT (Wiring Side)
+
*
)
21L-FG1L
(
'
&
%
$
11 – 1
Page 42
21L-FG1L
[2] PWB-A: MAIN UNIT (Chip Parts Side)
H
G
F
E
D
C
B
A
1
2 109
3
54
6
7
8
11 – 2
Page 43
[3] PWB-B: CRT UNIT (Wiring Side)
+
*
)
21L-FG1L
(
'
&
%
$
11 – 3
Page 44
21L-FG1L
[4] PWB-B: CRT UNIT (Chip Parts Side)
+
*
)
(
'
&
%
$
11 – 4
Page 45
PartsGuide
21L-FG1L
PARTS GUIDE
[1] PICTURE TUBE
[2] PRINTED WIRING BOARD
ASSEMBLIES
[3] MAIN UNIT
[4] CRT UNIT
MODEL
CONTENTS
No. XXXXXXXXXXXX
NO.S677221LFG1L
XXXXXXXX
21L-FG1L
[5] MISCELLANEOUS PARTS
[6] SUPPLIED ACCESSORIES
[7] CABINET PARTS
[8] PACKING PARTS
INDEX
Parts marked with " " are important for maintaining the safety of the set. Be sure to replace these
parts with specified ones for maintaining the safety and performance of the set.
This document has been published to be used
for after sales service only.
The contents are subject to change without notice.
Page 46
21L-FG1L
NO. PARTS CODE
PRICE
RANK
[1] PICTURE TUBE
!
!
VB550AJAC1S1E R Picture Tube
RCILGA115WJN1 R Degaussing Coil
QEARCA012WJZZ AG R Ground-Part
PMAGF3046CEZZ AF R Magnet
[2] PRINTED WIRING BOARD ASSEMBLIES
DUNTKE034WEA5 - - MAIN Unit
DUNTKE033WEA4 - - CRT Unit
[3] MAIN UNIT
TU201 RTUNQA037WJZZ R Tuner
!
IC301 VHIAN17821A-1 R AN17823A-1
IC501 VHILA78040N-1 AE R LA78040N-1
!
IC601 VHIPQ09RDA1-1 AF R PQ090RDA1SZ
IC701 VHISTRW5453-1 AM R I.C.
!
IC801 RH-IXC031WJZZQ R I.C.
IC1003 VHIBR24L04F-1Y AE R BR24L04F-WE2
IC3001 VHICXA2194Q-1S R I.C.
Q201 VS2SC2735//1EY R 2SC2735//1E
Q350 VS2SC3928AR-1Y AB R 2SC3928AR
Q351 VS2SC3928AR-1Y AB R 2SC3928AR
Q601 VS2SC2235Y/1E+ AE R 2SC2235
Q602 VSTT2140+++-F AG R TT2140
Q603 VS2SC3198-G-1+ AA R 2SC3198
Q604 VS2SC3928AR-1Y AB R 2SC3928AR
Q751 VS2SD468-C/-1+ AD R 2SD468
Q752 VS2SD468-C/-1+ AD R 2SD468
Q753 VS2SD468-C/-1+ AD R 2SD468
Q754 VS2SD468-C/-1+ AD R 2SD468
Q801 VS2SC3928AR-1Y AB R 2SC3928AR
Q802 VS2SA1530AR-1Y AB R 2SA1530AR
Q803 VS2SC3928AR-1Y AB R 2SC3928AR
Q805 VS2SA1530AR-1Y AB R 2SA1530AR
Q1001 VS2SC3928AR-1Y AB R 2SC3928AR
Q1002 VS2SC3928AR-1Y AB R 2SC3928AR
Q1801 VS2SC3928AR-1Y AB R 2SC3928AR
Q3001 VS2SC3928AR-1Y AB R 2SC3928AR
Q3002 VS2SC3928AR-1Y AB R 2SC3928AR
Q3004 VS2SC3928AR-1Y AB R 2SC3928AR
Q3005 VS2SC3928AR-1Y AB R 2SC3928AR
D201 RH-EX0676GEZZY AA R Zener Diode , 33V
D203 VHDHSS4148+-1Y AA R Diode
D204 VHDHSS4148+-1Y AA R Diode
D301 VHDHSS4148+-1Y AA R Diode
D393 RH-DX0247CEZZ AE R Diode , DX0247CE
D503 RH-EX0612GEZZY AB R Zener Diode , 5.1V
D505 RH-DX0441CEZZY AC R Diode , DX0441CE
D510 RH-DX0131CEZZY AC R Diode , DX0131CE
D602 VHD1SS244//-1Y AB R Diode , 1SS244
D603 RH-EX0667GEZZY AA R Zener Diode , 27V
D606 RH-DX0131CEZZY AC R Diode , DX0131CE
!
D701 RH-DX0476CEZZ AG R Diode , DX0476CE
D706 RH-DX0066GEZZY AC R Diode , DX0066GE
D707 RH-DX0066GEZZY AC R Diode , DX0066GE
D709 RH-DX0066GEZZY AC R Diode , DX0066GE
D715 RH-EX0615GEZZY AA R Zener Diode , 5.73V
D721 RH-DX0066GEZZY AC R Diode , DX0066GE
D722 RH-EX0669GEZZY AB R Zener Diode , 27.64V
D723 RH-EX0640GEZZY AA R Zener Diode , 12.03V
D732 RH-EX0626GEZZY AB R Zener Diode , 7.92V
D736 RH-EX0680GEZZY AB R Zener Diode , 34.49V
D751 RH-DXA044WJZZ R Diode , DXA044WJ
D752 RH-DX0247CEZZ AE R Diode , DX0247CE
D801 VHDHSS4148+-1Y AA R Diode
D802 RH-EX0630GEZZY AA R Zener Diode , 9.01V
D803 VHDHSS4148+-1Y AA R Diode
D806 RH-EX1393CEZZY AB R Zener Diode , 5.1V
D807 RH-EX0263TAZZY AC R Zener Diode , 8.36V
D808 RH-EX0263TAZZY AC R Zener Diode , 8.36V
D809 RH-EX0263TAZZY AC R Zener Diode , 8.36V
D810 VHDHSS4148+-1Y AA R Diode
D1001 RH-PX0013PEZZ AC R Photodiode
D1002 RH-EX0636GEZZY AA R Zener Diode , 10.71V
D1005 VHDHSS4148+-1Y AA R Diode
D1006 RH-EX1393CEZZY AB R Zener Diode , 5.1V
D1007 RH-EX1393CEZZY AB R Zener Diode , 5.1V
D1008 VHDHSS4148+-1Y AA R Diode
D1081 RH-DX0066GEZZY AC R Diode , DX0066GE
D1094 VHDHSS4148+-1Y AA R Diode
D1801 VHDHSS4148+-1Y AA R Diode
VA701 RH-VXA182WJZZ R Varistor
X801 RCRSAA019WJZZ AF R Crystal
L203 VP-DF270K0000Y AB R Peaking 27mH
L205 VP-XF2R2K0000Y AB R Peaking 2.2mH
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
2
Page 47
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
[3] MAIN UNIT
L206 VP-XF1R2K0000Y AB R Peaking 1.2mH
L602 RCILP0223CEZZ+ AD R Coil
L701 RCILFA187WJZZ AD R Coil
L751 RCILP0179CEZZ+ AD R Coil
L801 VP-DF100K0000Y AB R Peaking 10mH
L802 VP-CF100K0000Y AB R Peaking 10mH
L803 VP-CF220K0000Y AB R Peaking 22mH
L804 VP-CF100K0000Y AB R Peaking 10mH
L807 VP-DF100K0000Y AB R Peaking 10mH
L808 VP-XF150K0000Y AB R Peaking 15mH
L3501 VP-DF100K0000Y AB R Peaking 10mH
SF201 RFILCA055WJQZS R Coil
T602 RTRNFA132WJZZ R H-Volt Transformer
T603 RTRNZA058WJZZ AD R Transformer
T701 RTRNWA193WJZZ R Transformer
C202 VCEA0A1AW108M+ AC R 1000 10V Electrolytic
C203 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C206 VCEA0A1HW106M+ AB R 10 50V Electrolytic
C207 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C208 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C209 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C210 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C213 VCKYCY1HB102KY AA R 1 50V Ceramic
C214 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C301 VCEA0A1EW477M+ AB R 470 25V Electrolytic
C304 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C308 VCKYCY1HB102KY AA R 1 50V Ceramic
C310 VCEA0A1HW104M+ AB R 0.1 50V Electrolytic
C311 VCEA0A1HW104M+ AB R 0.1 50V Electrolytic
C313 VCKYCY1HB102KY AA R 1 50V Ceramic
C322 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C383 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C387 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C391 VCKYPA1HB102K+ AA R 1000p 50V Ceramic
C393 VCEA0A1EW108M+ AD R 1000 25V Electrolytic
C451 VCEA0A1CW477M+ AC R 470 16V Electrolytic
C501 VCFYFA1HA154J+ AE R 0.15 50V Mylar
C505 VCEA0A1HW107M+ AB R 100 50V Electrolytic
C508 VCFYAA2AA224J+ AD R 0.22 100V Mylar
C511 VCEA0A1VW477M+ AB R 470 35V Electrolytic
C512 VCKYPA2HB102K+ AA R 1000p 500V Ceramic
C513 RC-EZA332WJZZ+ AD R Capacitor
C515 VCEACA1HC335J+ AC R 3.3 50V Electrolytic
C601 VCQYTA1HM563J+ AB R 0.56 50V Mylar
C602 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C604 VCEA0A2EW336M+ AD R 33 250V Electrolytic
C606 VCKYPA2HB102K+ AA R 1000p 500V Ceramic
C607 VCFPVC3ZA802H AD R 8 1.8KV Metalized Polypro Film
C608 VCQYTA2AA103K+ AC R 0.01 100V Mylar
C610 VCEA0A1EW227M+ AB R 220 25V Electrolytic
C611 VCFPVC2EC334J AD R 0.33 200V Metalized Polypro Film
C642 VCEA0A1EW476M+ AB R 47 25V Electrolytic
C643 VCEA0A1CW477M+ AC R 470 16V Electrolytic
C650 VCKYPA2HB101K+ AB R 100p 500V Ceramic
C701 RC-FZ029SCEZZ AD R 220 275V Metalized Plastic Film
C702 RC-KZ0029CEZZ+ AC R 0.01 250V Ceramic
C703 RC-KZ0029CEZZ+ AC R 0.01 250V Ceramic
C704 RC-KZ0029CEZZ+ AC R 0.01 250V Ceramic
C705 RC-EZA097WJZZ AM R 220 400V Electrolytic
C706 VCFYFA1HA105J+ AE R 1 50V Mylar
C708 VCKYPA1HB221K+ AB R 220p 50V Ceramic
C709 VCQYTA1HM103J+ AB R 0.01 50V Mylar
C710 VCQYTA1HM103J+ AB R 0.01 50V Mylar
C711 VCKYPA1HB472K+ AB R 4700p 50V Ceramic
C719 VCEA0A1HW476M+ AB R 47 50V Electrolytic
C743 VCKYPH3DB561K AC R 560p 2KV Ceramic
C750 VCKYPA2HB102K+ AA R 1000p 500V Ceramic
C751 RC-KZ0102GEZZ AC R 2kV Ceramic
C752 VCKYPH3DB561K AC R 560p 2KV Ceramic
C753 RC-EZA523WJZZ AD R 100 160V Electrolytic
C754 RC-EZA522WJZZ AD R 33 160V Electrolytic
C756 VCEA0A1EW228M+ AE R 2200 25V Electrolytic
C757 VCCCCY1HH471JY AA R 470p 50V Ceramic
C784 RC-KZ1018CEZZ+ AC R 1000p 2KV Ceramic
C801 VCCCCY1HH330JY AA R 33p 50V Ceramic
C802 VCEA0A1AW107M+ AB R 100 10V Electrolytic
C803 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C804 VCEA0A1HW474M+ AB R 0.47 50V Electrolytic
C805 VCKYCY1HB153KY AA R 0.15 50V Ceramic
C806 VCEA0A1CW476M+ AB R 47 16V Electrolytic
C807 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C809 VCEA0A1CW476M+ AB R 47 16V Electrolytic
C810 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C811 VCFYFA1HA104J+ AA R 0.1 50V Mylar
C814 VCKYCY1CB563KY AB R 0.56 16V Ceramic
21L-FG1L
DESCRIPTION
3
Page 48
21L-FG1L
NO. PARTS CODE
[3] MAIN UNIT
C815 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C816 VCEA9M1HW474M+ AB R 0.47 50V Electrolytic
C817 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C818 VCEA0A1CW476M+ AB R 47 16V Electrolytic
C819 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C820 VCFYFA1HA104J+ AA R 0.1 50V Mylar
C821 VCEA0A1CW476M+ AB R 47 16V Electrolytic
C822 VCKYCY1HB104KY AA R 0.1 50V Ceramic
C823 VCKYCY1HB104KY AA R 0.1 50V Ceramic
C824 VCKYCY1CF105ZY AB R 1 16V Ceramic
C825 VCEA0A1HW474M+ AB R 0.47 50V Electrolytic
C826 VCEA0A1HW335M+ AB R 3.3 50V Electrolytic
C827 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C828 VCEA9M1HW474M+ AB R 0.47 50V Electrolytic
C830 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C831 VCEA0A1AW477M+ AC R 470 10V Electrolytic
C832 VCFYFA1HA104J+ AA R 0.1 50V Mylar
C833 VCEA0A1HW104M+ AB R 0.1 50V Electrolytic
C834 VCKYCY1CF104ZY AB R 0.1 16V Ceramic
C835 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C836 VCCCCY1HH680JY AA R 68p 50V Ceramic
C837 VCKYCY1HB104KY AA R 0.1 50V Ceramic
C838 VCEA0A1CW477M+ AC R 470 16V Electrolytic
C839 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C840 VCKYCY1CF105ZY AB R 1 16V Ceramic
C841 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C842 VCKYCY1HB104KY AA R 0.1 50V Ceramic
C843 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C847 VCKYPA1HB471K+ AA R 470p 50V Ceramic
C1001 VCEA0A1AW107M+ AB R 100 10V Electrolytic
C1002 VCCCCY1HH101JY AA R 100p 50V Ceramic
C1003 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C1004 VCKYCY1CF474ZY AB R 0.47 16V Ceramic
C1006 VCEA0A1HW225M+ AB R 2.2 50V Electrolytic
C1012 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
C1013 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C1016 VCKYCY1EF104ZY AA R 0.1 25V Ceramic
C1017 VCKYCY1HB221KY AA R 220 50V Ceramic
C1018 VCEA0A1HW105M+ AB R 1 50V Electrolytic
C1019 VCKYCY1HB102KY AA R 1 50V Ceramic
C1020 VCKYCY1HB561KY AA R 560 50V Ceramic
C1021 VCKYCY1EF104ZY AA R 0.1 25V Ceramic
C1022 VCEA0A0JW477M+ AC R 470 6.3V Electrolytic
C1081 VCFYFA1HA104J+ AA R 0.1 50V Mylar
C1840 VCEA0A1CW226M+ AC R 22 16V Electrolytic
C1841 VCEA0A1CW477M+ AC R 470 16V Electrolytic
C1842 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C1843 VCKYCY1HB104KY AA R 0.1 50V Ceramic
C1846 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
C1847 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
C1849 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
C1852 VCKYCY1HB103KY AA R 0.01 50V Ceramic
C1853 VCEA0A1CW476M+ AB R 47 16V Electrolytic
C1858 VCCCCY1HH220JY AA R 22p 50V Ceramic
C1860 VCCCCY1HH220JY AA R 22p 50V Ceramic
C1868 VCEA0A1CW336M+ AB R 33 16V Electrolytic
C3001 VCE9GA1HW475M+ AB R 4.7 50V Electrolytic
C3002 VCKYCY1HB562KY AA R 5.6 50V Ceramic
C3003 VCQYTA1HM123K+ AB R 0.12 50V Mylar
C3004 VCEA0A1HW105M+ AB R 1 50V Electrolytic
C3005 VCE9GA1HW475M+ AB R 4.7 50V Electrolytic
C3006 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C3007 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C3008 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C3009 VCEA0A1CW227M+ AC R 220 16V Electrolytic
C3010 VCE9GA1HW475M+ AB R 4.7 50V Electrolytic
C3011 VCEA0A1HW475M+ AB R 4.7 50V Electrolytic
C3012 VCE9GA1HW475M+ AB R 4.7 50V Electrolytic
C3013 VCKYCY1HB272KY AA R 2.7 50V Ceramic
C3014 VCQYTA1HM473K+ AB R 0.47 50V Mylar
C3015 VCEACA1HC335K+ AC R 3.3 50V Electrolytic
C3016 VCE9GA1HW475M+ AB R 4.7 50V Electrolytic
C3017 VCEACA1CC106K+ R 10 16V Electrolytic
C3018 VCEA0A1HW105M+ AB R 1 50V Electrolytic
C3019 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C3021 VCEA0A1CW106M+ AB R 10 16V Electrolytic
C3023 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C3024 VCKYCY1HF103ZY AA R 0.01 50V Ceramic
C3025 VCKYCY1HF473ZY AA R 0.47 50V Ceramic
C3026 VCKYCY1HF473ZY AA R 0.47 50V Ceramic
C3030 VCQYTA1HM682K+ AB R 6.8 50V Mylar
C3031 VCKYCY1HF682ZY AA R 6.8 50V Ceramic
C3034 VCEA0A1HW224M+ AB R 0.22 50V Electrolytic
C3037 VCEA0A1HW335M+ AB R 3.3 50V Electrolytic
C3038 VCEA0A1HW335M+ AB R 3.3 50V Electrolytic
C3039 VCEA0A1HW224M+ AB R 0.22 50V Electrolytic
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
4
Page 49
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
[3] MAIN UNIT
C3042 VCKYCY1HB681KY AA R 680 50V Ceramic
C3043 VCKYCY1HB681KY AA R 680 50V Ceramic
C3044 VCEA0A1EW476M+ AB R 47 25V Electrolytic
C3045 VCEA0A1HW335M+ AB R 3.3 50V Electrolytic
C3046 VCEA0A1HW335M+ AB R 3.3 50V Electrolytic
RJ2 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ5 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ8 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ12 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ16 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ19 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ20 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
RJ24 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
R201 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R202 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R204 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R205 VRS-CY1JF680JY AA R 68 1/16W Metal Oxide
R206 VRS-CY1JF122JY AA R 1.2K 1/16W Metal Oxide
R207 VRS-CY1JF221JY AA R 220 1/16W Metal Oxide
R208 VRS-CY1JF331JY AA R 330 1/16W Metal Oxide
R209 VRS-CY1JF392JY AA R 3.9K 1/16W Metal Oxide
R216 VRS-RG3LB393J+ AC R 39K 3W Metal Film
R220 VRS-CY1JF221JY AA R 220 1/16W Metal Oxide
R301 VRD-RA2BE102JY AA R 1K 1/8W Carbon
R302 VRN-KT3LB1R8J R 1.8 3W Metal Oxide
R303 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R304 VRD-RA2BE683JY AA R 68K 1/8W Carbon
R305 VRS-CY1JF274JY AA R 270K 1/16W Metal Oxide
R307 VRS-CY1JF222JY AA R 2.2K 1/16W Metal Oxide
R308 VRD-RA2BE392JY AA R 3.9K 1/8W Carbon
R314 VRD-RA2BE392JY AA R 3.9K 1/8W Carbon
R315 VRS-CY1JF222JY AA R 2.2K 1/16W Metal Oxide
R316 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R353 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R356 VRD-RA2BE102JY AA R 1K 1/8W Carbon
R362 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R366 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R372 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R373 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R374 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R376 VRD-RA2BE472JY AA R 4.7K 1/8W Carbon
R458 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R459 VRD-RA2EE750JY AA R 75 1/4W Carbon
R461 VRS-CY1JF750JY AA R 75 1/16W Metal Oxide
R462 VRD-RA2BE101JY AA R 100 1/8W Carbon
R503 VRN-RL3DB1R0J+ AB R 1 2W Metal Film
R504 VRS-CY1JF222JY AA R 2.2K 1/16W Metal Oxide
R506 VRS-RG3AB331J+ AB R 330 1W Metal Oxide
R507 VRD-RM2HD1R0JY AA R 1 1/2W Carbon
R513 VRD-RM2HD333JY AA R 33K 1/2W Carbon
R514 VRD-RM2HD682JY AA R 6.8K 1/2W Carbon
R520 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R523 VRD-RA2BE103JY AA R 10K 1/8W Carbon
R524 VRD-RA2BE103JY AA R 10K 1/8W Carbon
R525 VRD-RA2BE122JY AA R 1.2K 1/8W Carbon
R601 VRD-RM2HD270JY AA R 27 1/2W Carbon
R602 VRD-RA2BE393JY AA R 39K 1/8W Carbon
R603 VRD-RA2BE393JY AA R 39K 1/8W Carbon
R604 VRD-RA2BE473JY AA R 47K 1/8W Carbon
R605 VRD-RM2HD104JY AA R 100K 1/2W Carbon
R606 VRN-RL3LBR22J+ AD R 22 3W Metal Film
R608 VRD-RM2HD102JY AA R 1K 1/2W Carbon
R609 VRD-RM2HD270JY AA R 27 1/2W Carbon
R611 VRN-RL3AB1R8J+ AB R 1.8 1W Metal Film
R612 VRD-RM2HD270JY AA R 27 1/2W Carbon
R614 VRD-RA2BE154JY AA R 150K 1/8W Carbon
R615 VRD-RA2BE102JY AA R 1K 1/8W Carbon
R616 VRD-RA2BE102JY AA R 1K 1/8W Carbon
R617 VRS-CY1JF123JY AA R 12K 1/16W Metal Oxide
R618 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R621 VRN-RL2HC4R7J+ AB R 4.7 1/2W Metal Oxide
R622 VRS-VV3DB682J AA R 6.8K 2W Metal Oxide
R631 VRS-RG3LB391J+ R 390 3W Metal Oxide
R637 VRD-RA2BE331JY AA R 330 1/8W Carbon
R638 VRD-RA2BE181JY AA R 180 1/8W Carbon
R639 VRD-RM2HD271JY AA R 270 1/2W Carbon
R642 VRN-RL3DB1R0J+ AB R 1 2W Metal Film
R661 VRD-RA2BE102JY AA R 1K 1/8W Carbon
R662 VRD-RA2BE103JY AA R 10K 1/8W Carbon
R702 VRS-VV3DB124J AA R 120K 2W Metal Oxide
R704 VRD-RA2BE221JY AA R 220 1/8W Carbon
R705 VRN-RL3DBR82J+ AB R 82 2W Metal Film
R706 VRN-RL3DBR22J+ AB R 22 2W Metal Film
R710 VRD-RM2HD1R0JY AA R 1 1/2W Carbon
R720 VRD-RA2EE472JY AA R 4.7K 1/4W Carbon
21L-FG1L
DESCRIPTION
5
Page 50
21L-FG1L
NO. PARTS CODE
[3] MAIN UNIT
R722 VRD-RA2BE153JY AA R 15K 1/8W Carbon
R726 VRN-RL2HCR47J+ AB R 0.47 1/2W Metal Oxide
R733 VRD-RA2BE273JY AA R 27K 1/8W Carbon
R751 RR-DZ0049CEZZY R 39M 1/2W Carbon Film
R752 RR-DZ0049CEZZY R 39M 1/2W Carbon Film
R753 VRD-RM2HD124JY AA R 120K 1/2W Carbon
R754 VRN-RL3AB8R2J+ AB R 8.2 1W Metal Film
R755 VRS-RG3DB121J+ AB R 120 2W Metal Film
R801 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R802 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R803 VRD-RA2BE101JY AA R 100 1/8W Carbon
R804 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R805 VRD-RA2BE101JY AA R 100 1/8W Carbon
R806 VRS-CY1JF822JY AA R 8.2K 1/16W Metal Oxide
R807 VRS-CY1JF124JY AA R 120K 1/16W Metal Oxide
R808 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R809 VRD-RA2BE123JY AA R 12K 1/8W Carbon
R810 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R811 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R812 VRS-CY1JF822JY AA R 8.2K 1/16W Metal Oxide
R813 VRD-RM2HD151JY AA R 150 1/2W Carbon
R814 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R815 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R816 VRS-CY1JF471JY AA R 470 1/16W Metal Oxide
R817 VRS-CY1JF331JY AA R 330 1/16W Metal Oxide
R818 VRS-CY1JF220JY AA R 22 1/16W Metal Oxide
R819 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R820 VRD-RA2BE101JY AA R 100 1/8W Carbon
R822 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R823 VRS-CY1JF472JY AA R 4.7K 1/16W Metal Oxide
R824 VRS-CY1JF181JY AA R 180 1/16W Metal Oxide
R825 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R826 VRS-CY1JF181JY AA R 180 1/16W Metal Oxide
R827 VRS-CY1JF181JY AA R 180 1/16W Metal Oxide
R828 VRS-CY1JF223JY AA R 22K 1/16W Metal Oxide
R829 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R831 VRD-RA2BE122JY AA R 1.2K 1/8W Carbon
R832 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R833 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R834 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R835 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R837 VCKYCY1HB104KY AA R 0.1 50V Ceramic
R838 VRS-CY1JF472JY AA R 4.7K 1/16W Metal Oxide
R840 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R841 VRS-CY1JF470JY AA R 47 1/16W Metal Oxide
R843 VRS-CY1JF222JY AA R 2.2K 1/16W Metal Oxide
R1003 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R1004 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1008 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1010 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R1011 VRS-CY1JF183JY AA R 18K 1/16W Metal Oxide
R1012 VRD-RA2BE183JY AA R 18K 1/8W Carbon
R1013 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1014 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R1015 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1016 VRD-RA2BE332JY AA R 3.3K 1/8W Carbon
R1017 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1018 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R1019 VRD-RA2BE101JY AA R 100 1/8W Carbon
R1020 VRS-CY1JF183JY AA R 18K 1/16W Metal Oxide
R1021 VRS-CY1JF822JY AA R 8.2K 1/16W Metal Oxide
R1022 VRS-CY1JF183JY AA R 18K 1/16W Metal Oxide
R1024 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R1025 VRD-RA2BE103JY AA R 10K 1/8W Carbon
R1026 VRS-CY1JF183JY AA R 18K 1/16W Metal Oxide
R1027 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R1028 VRD-RA2BE391JY AA R 390 1/8W Carbon
R1030 VRS-CY1JF103JY AA R 10K 1/16W Metal Oxide
R1031 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R1032 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R1038 VRS-CY1JF562JY AA R 5.6K 1/16W Metal Oxide
R1039 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R1040 VRS-CY1JF101JY AA R 100 1/16W Metal Oxide
R1041 VRS-CY1JF105JY AA R 1M 1/16W Metal Oxide
R1042 VRS-CY1JF471JY AA R 470 1/16W Metal Oxide
R1044 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R1045 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R1046 VRS-CY1JF472JY AA R 4.7K 1/16W Metal Oxide
R1056 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R1074 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R1087 VRS-CY1JF000JY AA R 0 1/16W Metal Oxide
R1092 VRS-CY1JF472JY AA R 4.7K 1/16W Metal Oxide
R1801 VRS-CY1JF222JY AA R 2.2K 1/16W Metal Oxide
R1802 VRS-CY1JF124JY AA R 120K 1/16W Metal Oxide
R1803 VRS-CY1JF475JY AA R 4.7M 1/16W Metal Oxide
R1894 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
DESCRIPTION
6
Page 51
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
[3] MAIN UNIT
R1895 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R1896 VRS-CY1JF473JY AA R 47K 1/16W Metal Oxide
R3001 VRD-RA2BE221JY AA R 220 1/8W Carbon
R3002 VRD-RA2BE221JY AA R 220 1/8W Carbon
R3003 VRS-CY1JF105JY AA R 1M 1/16W Metal Oxide
R3004 VRS-CY1JF104JY AA R 100K 1/16W Metal Oxide
R3005 VRS-CY1JF623JY AA R 62K 1/16W Metal Oxide
R3007 VRS-CY1JF332JY AA R 3.3K 1/16W Metal Oxide
R3008 VRS-CY1JF302JY AA R 3K 1/16W Metal Oxide
R3010 VRS-CY1JF392JY AA R 3.9K 1/16W Metal Oxide
R3011 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R3012 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R3018 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R3021 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R3026 VRD-RA2BE331JY AA R 330 1/8W Carbon
R3027 VRS-CY1JF392JY AA R 3.9K 1/16W Metal Oxide
R3028 VRS-CY1JF683JY AA R 68K 1/16W Metal Oxide
R3029 VRS-CY1JF392JY AA R 3.9K 1/16W Metal Oxide
R3030 VRS-CY1JF683JY AA R 68K 1/16W Metal Oxide
R3031 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R3032 VRS-CY1JF223JY AA R 22K 1/16W Metal Oxide
R3033 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
R3034 VRS-CY1JF182JY AA R 1.8K 1/16W Metal Oxide
R3035 VRS-CY1JF223JY AA R 22K 1/16W Metal Oxide
R3036 VRS-CY1JF102JY AA R 1K 1/16W Metal Oxide
S701 QSW-P0612CEZZ AG R Switch , POWER
S1001 QSW-KA019WJZZ+ AC R Switch , CH UP
S1002 QSW-KA019WJZZ+ AC R Switch , CH DOWN
S1003 QSW-KA019WJZZ+ AC R Switch , VOL UP
S1004 QSW-KA019WJZZ+ AC R Switch , VOL DOWN
S1005 QSW-KA019WJZZ+ AC R Switch , MENU
!
F701 QFS-C3225CEZZ AC R Fuse , 3.15A 250V
FH701 QFSHD1013CEZZ+ AC R Fuse Holder
FH702 QFSHD1014CEZZ+ AC R Fuse Holder
J405 QTANJA080WJZZ R Jack
P302 QPLGN0461CEZZA AB R Plug ,4Pin(S)
P601 QPLGN0660CEZZ AC R Plug ,6Pin(F)
P602 LHLDW1104PEZZ AB R Plug
P701 QPLGN0260CEZZ AC R Plug ,2Pin(M)
P702 QPLGN0269GEZZ AB R Plug ,2Pin
P1001 LHLDW1105PEZZ AB R Plug
P1002 QPLGN0561CEZZ AB R Plug ,5Pin(BC)
RMC1001 RRMCUA022WJZZ AG R Remote Receiver
RDA501 PRDARA120WJFW AD R Heat Sink for IC501
RDA601 PRDARA167WJFW AD R Heat Sink for IC601
RDA602 PRDARA361WJFW R Heat Sink for Q602
RDA701 PRDARA119WJFW AF R Heat Sink for IC701
TP801 QLUGP0111GEFW AA R Lug
[4] CRT UNIT
Q853 RH-TX0110BMZZ+ AC R TX0110
Q854 RH-TX0110BMZZ+ AC R TX0110
Q855 RH-TX0110BMZZ+ AC R TX0110
Q894 VS2SA1530AR-1Y AB R 2SA1530AR
D859 VHDHSS4148+-1Y AA R Diode
D896 RH-EX0616GEZZY AA R Zener Diode , 5.6V
D898 VHDHSS4148+-1Y AA R Diode
L851 VP-MK820K0000+ AB R Peaking 82mH
C851 VCKYPA1HB561K+ AA R 560p 50V Ceramic
C852 VCKYPA1HB271K+ AB R 270p 50V Ceramic
C853 VCKYPA1HB331K+ AA R 330p 50V Ceramic
C880 RC-KZ0016CEZZ AC R 10000p 1.5KV Ceramic
C893 VCEA0A1CW336M+ AB R 33 16V Electrolytic
R849 VRS-CY1JF271JY AA R 270 1/16W Metal Oxide
R850 VRS-CY1JF470JY AA R 47 1/16W Metal Oxide
R851 VRS-CY1JF470JY AA R 47 1/16W Metal Oxide
R852 VRS-CY1JF470JY AA R 47 1/16W Metal Oxide
R854 VRS-CY1JF271JY AA R 270 1/16W Metal Oxide
R855 VRS-CY1JF271JY AA R 270 1/16W Metal Oxide
!
!
!
R859 VRS-VV3DB153J AA R 15K 12W Metal Oxide
R861 VRS-VV3DB153J AA R 15K 12W Metal Oxide
R863 VRS-VV3DB153J AA R 15K 12W Metal Oxide
R864 VRD-RA2BE470JY AA R 47 1/8W Carbon
R876 VRS-CY1JF121JY AA R 120 1/16W Metal Oxide
R877 VRS-CY1JF121JY AA R 120 1/16W Metal Oxide
R878 VRS-CY1JF121JY AA R 120 1/16W Metal Oxide
R880 VRD-RM2HD332JY AA R 3.3K 1/2W Carbon
R881 VRD-RM2HD332JY AA R 3.3K 1/2W Carbon
R882 VRD-RM2HD332JY AA R 3.3K 1/2W Carbon
R891 VRS-CY1JF152JY AA R 1.5K 1/16W Metal Oxide
R892 VRS-CY1JF391JY AA R 390 1/16W Metal Oxide
R894 VRS-CY1JF152JY AA R 1.5K 1/16W Metal Oxide
R895 VRD-RA2BE561JY AA R 560 1/8W Carbon
P860 LHLDW1104PEZZ AB R Plug 4Pin (H)
21L-FG1L
DESCRIPTION
7
Page 52
21L-FG1L
NO. PARTS CODE
PRICE
RANK
[4] CRT UNIT
P880 LHLDW1105PEZZ AB R Plug 5Pin (K)
SC851 QSOCVA023WJZZ AE R Socket , 12Pin
[5] MISCELLANEOUS PARTS
ACC701 QACCZA079WJPZ R AC Cord
!
SP301 VSP9050PA02WA AH R SPEAKER 16 OHM
QCNW-F201WJPZ R SP WIRE (+--+)
QCNW-A230WJZZ AD R H-WIRE
QCNW-A720WJZZ AD R K-WIRE
[6] SUPPLIED ACCESSORIES
RRMCGA257WJSB R Infrared Remote Control Unit
TINS-D209WJZZ R E/SPA Operation Manual
UBATU0247AJZZ R Battery
NEW
MARK
[7] CABINET PARTS
PAR T
DELIVERY
1-1
DESCRIPTION
1
2-1
1-2
1-5
2
1-4
1-3
1-6
3
8
Page 53
21L-FG1L
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVELY
[7] CABINET PARTS
1 CCABAB834WEV0 - R Front Cabinet Ass'y
1-1 Not Available - - Front Cabinet
1-2 GCOVAB580WJSA - R R/C Cover
1-3 HBDGB3155CESA - R Sharp Badge
1-4 JBTN-A551WJSB - R Power Button
1-5 MSPRCA067WJFW - R Power Button Spring
1-6 JBTN-A552WJSC - R Control Button
2 CCABBA755WEV1 - R Rear Cabinet Ass'y
2-1 Not Available - - Rear Cabinet
3 LHLDWA101WJZZ - R AC Cord Hook
[8] PACKING PARTS
POLYETHYLENE BAG
*
OPERATION MANUAL
BATTERIES
7
HOSO PP
*
R/C UNIT
6
PACKING FOAM
*
DESCRIPTION
5
CASE LABEL
*
USE 2 TAPES TO FIX
THE PACKING CASE
MARK*: NON REPLACEMENT ITEMS
NO. PARTS CODE
PRICE
RANK
[8] PACKING PARTS
4 SPAKCD591WJZZ - - Packing Case
5 TLABZB556WJZZ - - Case Label
6 SPAKXB002WJZZ - - Buffer Material
7 SPAKPA771WJZZ - - HOSO PP
NEW
MARK
PAR T
DELIVELY
4
PACKING CASE
*
DESCRIPTION
9
Page 54
21L-FG1L
NO. PARTS CODE
PRICE
RANK
NEW
MARK
PAR T
DELIVERY
INDEX
PRICE
NEW
PARTS CODE No.
[ C ]
CCABAB834WEV0 7-1 - R
CCABBA755WEV1 7-2 - R
[ D ]
DUNTKE033WEA4 2- - DUNTKE034WEA5 2- - -
[ G ]
GCOVAB580WJSA 7-1-2 - R
[ H ]
HBDGB3155CESA 7-1-3 - R
[ J ]
JBTN-A551WJSB 7-1-4 - R
JBTN-A552WJSC 7-1-6 - R
[ L ]
LHLDW1104PEZZ 3-P602 AB R
" 4-P860 AB R
LHLDW1105PEZZ 3-P1001 AB R
" 4-P880 AB R
LHLDWA101WJZZ 7-3 - R
[ M ]
MSPRCA067WJFW 7-1-5 - R
[ N ]
Not Available 7-1-1 - -
" 7-2-1 - -
[ P ]
PMAGF3046CEZZ 1- AF R
PRDARA119WJFW 3-RDA701 AF R
PRDARA120WJFW 3-RDA501 AD R
PRDARA167WJFW 3-RDA601 AD R
PRDARA361WJFW 3-RDA602 R
[ Q ]
QACCZA079WJPZ 5-ACC701 R
QCNW-A230WJZZ 5- AD R
QCNW-A720WJZZ 5- AD R
QCNW-F201WJPZ 5- R
QEARCA012WJZZ 1- AG R
QFS-C3225CEZZ 3-F701 AC R
QFSHD1013CEZZ+ 3-FH701 AC R
QFSHD1014CEZZ+ 3-FH702 AC R
QLUGP0111GEFW 3-TP801 AA R
QPLGN0260CEZZ 3-P701 AC R
QPLGN0269GEZZ 3-P702 AB R
QPLGN0461CEZZA 3-P302 AB R
QPLGN0561CEZZ 3-P1002 AB R
QPLGN0660CEZZ 3-P601 AC R
QSOCVA023WJZZ 4-SC851 AE R
QSW-KA019WJZZ+ 3-S1001 AC R
" 3-S1002 AC R
" 3-S1003 AC R
" 3-S1004 AC R
" 3-S1005 AC R
QSW-P0612CEZZ 3-S701 AG R
QTANJA080WJZZ 3-J405 R
[ R ]
RC-EZA097WJZZ 3-C705 AM R
RC-EZA332WJZZ+ 3-C513 AD R
RC-EZA522WJZZ 3-C754 AD R
RC-EZA523WJZZ 3-C753 AD R
RC-FZ029SCEZZ 3-C701 AD R
RCILFA187WJZZ 3-L701 AD R
RCILGA115WJN1 1- R
RCILP0179CEZZ+ 3-L751 AD R
RCILP0223CEZZ+ 3-L602 AD R
RC-KZ0016CEZZ 4-C880 AC R
RC-KZ0029CEZZ+ 3-C702 AC R
" 3-C703 AC R
" 3-C704 AC R
RC-KZ0102GEZZ 3-C751 AC R
RC-KZ1018CEZZ+ 3-C784 AC R
RCRSAA019WJZZ 3-X801 AF R
RFILCA055WJQZS 3-SF201 R
RH-DX0066GEZZY 3-D706 AC R
" 3-D707 AC R
" 3-D709 AC R
" 3-D721 AC R
" 3-D1081 AC R
RANK
MARK
PAR T
RANK
DESCRIPTION
10
Page 55
PRICE
NEW
PARTS CODE No.
PARTS CODE No.
" 3-D606 AC R
RH-DX0247CEZZ 3-D393 AE R
" 3-D752 AE R
RH-DX0441CEZZY 3-D505 AC R
RH-DX0476CEZZ 3-D701 AG R
RH-DXA044WJZZ 3-D751 R
RH-EX0263TAZZY 3-D807 AC R
" 3-D808 AC R
" 3-D809 AC R
RH-EX0612GEZZY 3-D503 AB R
RH-EX0615GEZZY 3-D715 AA R
RH-EX0616GEZZY 4-D896 AA R
RH-EX0626GEZZY 3-D732 AB R
RH-EX0630GEZZY 3-D802 AA R
RH-EX0636GEZZY 3-D1002 AA R
RH-EX0640GEZZY 3-D723 AA R
RH-EX0667GEZZY 3-D603 AA R
RH-EX0669GEZZY 3-D722 AB R
RH-EX0676GEZZY 3-D201 AA R
RH-EX0680GEZZY 3-D736 AB R
RH-EX1393CEZZY 3-D806 AB R
" 3-D1006 AB R
" 3-D1007 AB R
RH-IXC031WJZZQ 3-IC801 R
RH-PX0013PEZZ 3-D1001 AC R
RH-TX0110BMZZ+ 4-Q853 AC R
" 4-Q854 AC R
" 4-Q855 AC R
RH-VXA182WJZZ 3-VA701 R
RR-DZ0049CEZZY 3-R751 R
" 3-R752 R
RRMCGA257WJSB 6- R
RRMCUA022WJZZ 3-RMC1001 AG R
RTRNFA132WJZZ 3-T602 R
RTRNWA193WJZZ 3-T701 R
RTRNZA058WJZZ 3-T603 AD R
RTUNQA037WJZZ 3-TU201 R
[ S ]
SPAKCD591WJZZ 8-4 - SPAKPA771WJZZ 8-7 - SPAKXB002WJZZ 8-6 - -
[ T ]
TINS-D209WJZZ 6- R
TLABZB556WJZZ 8-5 - -
[ U ]
UBATU0247AJZZ 6- R
[ V ]
VB550AJAC1S1E 1- R
VCCCCY1HH101JY 3-C1002 AA R
VCCCCY1HH220JY 3-C1858 AA R
" 3-C1860 AA R
VCCCCY1HH330JY 3-C801 AA R
VCCCCY1HH471JY 3-C757 AA R
VCCCCY1HH680JY 3-C836 AA R
VCE9GA1HW475M+ 3-C3001 AB R
" 3-C3005 AB R
" 3-C3010 AB R
" 3-C3012 AB R
" 3-C3016 AB R
VCEA0A0JW477M+ 3-C1022 AC R
VCEA0A1AW107M+ 3-C802 AB R
" 3-C1001 AB R
VCEA0A1AW108M+ 3-C202 AC R
VCEA0A1AW477M+ 3-C831 AC R
VCEA0A1CW106M+ 3-C383 AB R
" 3-C387 AB R
" 3-C827 AB R
" 3-C1003 AB R
" 3-C3006 AB R
" 3-C3019 AB R
" 3-C3021 AB R
VCEA0A1CW226M+ 3-C1840 AC R
VCEA0A1CW227M+ 3-C3009 AC R
VCEA0A1CW336M+ 3-C1868 AB R
" 4-C893 AB R
VCEA0A1CW476M+ 3-C806 AB R
" 3-C809 AB R
" 3-C818 AB R
" 3-C821 AB R
RANK
PRICE
RANK
MARK
NEW
MARK
PART
RANK
PART
RANK
21L-FG1L
PRICE
NEW
PARTS CODE No.
" 3-C1853 AB R
VCEA0A1CW477M+ 3-C451 AC R
" 3-C643 AC R
" 3-C838 AC R
" 3-C1841 AC R
VCEA0A1EW108M+ 3-C393 AD R
VCEA0A1EW227M+ 3-C610 AB R
VCEA0A1EW228M+ 3-C756 AE R
VCEA0A1EW476M+ 3-C642 AB R
" 3-C3044 AB R
VCEA0A1EW477M+ 3-C301 AB R
VCEA0A1HW104M+ 3-C310 AB R
" 3-C311 AB R
" 3-C833 AB R
VCEA0A1HW105M+ 3-C1018 AB R
" 3-C3004 AB R
" 3-C3018 AB R
VCEA0A1HW106M+ 3-C206 AB R
VCEA0A1HW107M+ 3-C505 AB R
VCEA0A1HW224M+ 3-C3034 AB R
" 3-C3039 AB R
VCEA0A1HW225M+ 3-C1006 AB R
VCEA0A1HW335M+ 3-C826 AB R
" 3-C3037 AB R
" 3-C3038 AB R
" 3-C3045 AB R
" 3-C3046 AB R
VCEA0A1HW474M+ 3-C804 AB R
" 3-C825 AB R
VCEA0A1HW475M+ 3-C304 AB R
" 3-C322 AB R
" 3-C602 AB R
" 3-C843 AB R
" 3-C3007 AB R
" 3-C3011 AB R
VCEA0A1HW476M+ 3-C719 AB R
VCEA0A1VW477M+ 3-C511 AB R
VCEA0A2EW336M+ 3-C604 AD R
VCEA9M1HW474M+ 3-C816 AB R
" 3-C828 AB R
VCEACA1CC106K+ 3-C3017 R
VCEACA1HC335J+ 3-C515 AC R
VCEACA1HC335K+ 3-C3015 AC R
VCFPVC2EC334J 3-C611 AD R
VCFPVC3ZA802H 3-C607 AD R
VCFYAA2AA224J+ 3-C508 AD R
VCFYFA1HA104J+ 3-C811 AA R
" 3-C820 AA R
" 3-C832 AA R
" 3-C1081 AA R
VCFYFA1HA105J+ 3-C706 AE R
VCFYFA1HA154J+ 3-C501 AE R
VCKYCY1CB563KY 3-C814 AB R
VCKYCY1CF104ZY 3-C834 AB R
VCKYCY1CF105ZY 3-C824 AB R
" 3-C840 AB R
VCKYCY1CF474ZY 3-C1004 AB R
VCKYCY1EF104ZY 3-C1016 AA R
" 3-C1021 AA R
VCKYCY1HB102KY 3-C213 AA R
" 3-C308 AA R
" 3-C313 AA R
" 3-C1019 AA R
VCKYCY1HB103KY 3-C803 AA R
" 3-C807 AA R
" 3-C815 AA R
" 3-C819 AA R
" 3-C830 AA R
" 3-C835 AA R
" 3-C841 AA R
" 3-C1013 AA R
" 3-C1842 AA R
" 3-C1852 AA R
VCKYCY1HB104KY 3-C822 AA R
" 3-C823 AA R
" 3-C837 AA R
" 3-C842 AA R
" 3-R837 AA R
" 3-C1843 AA R
VCKYCY1HB153KY 3-C805 AA R
RANK
MARK
PART
RANK
11
Page 56
21L-FG1L
PRICE
NEW
PARTS CODE No.
VCKYCY1HB221KY 3-C1017 AA R
VCKYCY1HB272KY 3-C3013 AA R
VCKYCY1HB561KY 3-C1020 AA R
VCKYCY1HB562KY 3-C3002 AA R
VCKYCY1HB681KY 3-C3042 AA R
" 3-C3043 AA R
VCKYCY1HF103ZY 3-C203 AA R
" 3-C207 AA R
" 3-C208 AA R
" 3-C209 AA R
" 3-C210 AA R
" 3-C214 AA R
" 3-C810 AA R
" 3-C817 AA R
" 3-C839 AA R
" 3-C3008 AA R
" 3-C3023 AA R
" 3-C3024 AA R
VCKYCY1HF473ZY 3-C3025 AA R
" 3-C3026 AA R
VCKYCY1HF682ZY 3-C3031 AA R
VCKYPA1HB102K+ 3-C391 AA R
VCKYPA1HB221K+ 3-C708 AB R
VCKYPA1HB271K+ 4-C852 AB R
VCKYPA1HB331K+ 4-C853 AA R
VCKYPA1HB471K+ 3-C847 AA R
VCKYPA1HB472K+ 3-C711 AB R
VCKYPA1HB561K+ 4-C851 AA R
VCKYPA2HB101K+ 3-C650 AB R
VCKYPA2HB102K+ 3-C512 AA R
" 3-C606 AA R
" 3-C750 AA R
VCKYPH3DB561K 3-C743 AC R
" 3-C752 AC R
VCQYTA1HM103J+ 3-C709 AB R
" 3-C710 AB R
VCQYTA1HM123K+ 3-C3003 AB R
VCQYTA1HM473K+ 3-C3014 AB R
VCQYTA1HM563J+ 3-C601 AB R
VCQYTA1HM682K+ 3-C3030 AB R
VCQYTA2AA103K+ 3-C608 AC R
VHD1SS244//-1Y 3-D602 AB R
VHDHSS4148+-1Y 3-D203 AA R
" 3-D204 AA R
" 3-D301 AA R
" 3-D801 AA R
" 3-D803 AA R
" 3-D810 AA R
" 3-D1005 AA R
" 3-D1008 AA R
" 3-D1094 AA R
" 3-D1801 AA R
" 4-D859 AA R
" 4-D898 AA R
VHIAN17821A-1 3-IC301 R
VHIBR24L04F-1Y 3-IC1003 AE R
VHICXA2194Q-1S 3-IC3001 R
VHILA78040N-1 3-IC501 AE R
VHIPQ09RDA1-1 3-IC601 AF R
VHISTRW5453-1 3-IC701 AM R
VP-CF100K0000Y 3-L802 AB R
" 3-L804 AB R
VP-CF220K0000Y 3-L803 AB R
VP-DF100K0000Y 3-L801 AB R
" 3-L807 AB R
" 3-L3501 AB R
VP-DF270K0000Y 3-L203 AB R
VP-MK820K0000+ 4-L851 AB R
VP-XF150K0000Y 3-L808 AB R
VP-XF1R2K0000Y 3-L206 AB R
VP-XF2R2K0000Y 3-L205 AB R
VRD-RA2BE101JY 3-R462 AA R
" 3-R803 AA R
" 3-R805 AA R
" 3-R820 AA R
" 3-R1004 AA R
" 3-R1008 AA R
" 3-R1013 AA R
" 3-R1015 AA R
" 3-R1017 AA R
" 3-R1019 AA R
VRD-RA2BE102JY 3-R301 AA R
RANK
MARK
PAR T
RANK
PRICE
NEW
PARTS CODE No.
" 3-R356 AA R
" 3-R615 AA R
" 3-R616 AA R
" 3-R661 AA R
VRD-RA2BE103JY 3-R523 AA R
" 3-R524 AA R
" 3-R662 AA R
" 3-R1025 AA R
VRD-RA2BE122JY 3-R525 AA R
" 3-R831 AA R
VRD-RA2BE123JY 3-R809 AA R
VRD-RA2BE153JY 3-R722 AA R
VRD-RA2BE154JY 3-R614 AA R
VRD-RA2BE181JY 3-R638 AA R
VRD-RA2BE183JY 3-R1012 AA R
VRD-RA2BE221JY 3-R704 AA R
" 3-R3001 AA R
" 3-R3002 AA R
VRD-RA2BE273JY 3-R733 AA R
VRD-RA2BE331JY 3-R637 AA R
" 3-R3026 AA R
VRD-RA2BE332JY 3-R1016 AA R
VRD-RA2BE391JY 3-R1028 AA R
VRD-RA2BE392JY 3-R308 AA R
" 3-R314 AA R
VRD-RA2BE393JY 3-R602 AA R
" 3-R603 AA R
VRD-RA2BE470JY 4-R864 AA R
VRD-RA2BE472JY 3-R376 AA R
VRD-RA2BE473JY 3-R604 AA R
VRD-RA2BE561JY 4-R895 AA R
VRD-RA2BE683JY 3-R304 AA R
VRD-RA2EE472JY 3-R720 AA R
VRD-RA2EE750JY 3-R459 AA R
VRD-RM2HD102JY 3-R608 AA R
VRD-RM2HD104JY 3-R605 AA R
VRD-RM2HD124JY 3-R753 AA R
VRD-RM2HD151JY 3-R813 AA R
VRD-RM2HD1R0JY 3-R507 AA R
" 3-R710 AA R
VRD-RM2HD270JY 3-R601 AA R
" 3-R609 AA R
" 3-R612 AA R
VRD-RM2HD271JY 3-R639 AA R
VRD-RM2HD332JY 4-R880 AA R
" 4-R881 AA R
" 4-R882 AA R
VRD-RM2HD333JY 3-R513 AA R
VRD-RM2HD682JY 3-R514 AA R
VRN-KT3LB1R8J 3-R302 R
VRN-RL2HC4R7J+ 3-R621 AB R
VRN-RL2HCR47J+ 3-R726 AB R
VRN-RL3AB1R8J+ 3-R611 AB R
VRN-RL3AB8R2J+ 3-R754 AB R
VRN-RL3DB1R0J+ 3-R503 AB R
" 3-R642 AB R
VRN-RL3DBR22J+ 3-R706 AB R
VRN-RL3DBR82J+ 3-R705 AB R
VRN-RL3LBR22J+ 3-R606 AD R
VRS-CY1JF000JY 3-RJ2 AA R
" 3-RJ5 AA R
" 3-RJ8 AA R
" 3-RJ12 AA R
" 3-RJ16 AA R
" 3-RJ19 AA R
" 3-RJ20 AA R
" 3-RJ24 AA R
" 3-C1012 AA R
" 3-C1846 AA R
" 3-C1847 AA R
" 3-C1849 AA R
" 3-R1087 AA R
VRS-CY1JF101JY 3-R201 AA R
" 3-R202 AA R
" 3-R804 AA R
" 3-R808 AA R
" 3-R814 AA R
" 3-R815 AA R
" 3-R840 AA R
" 3-R1014 AA R
" 3-R1024 AA R
" 3-R1031 AA R
RANK
MARK
PART
RANK
12
Page 57
PRICE
NEW
PARTS CODE No.
" 3-R1040 AA R
VRS-CY1JF102JY 3-R353 AA R
" 3-R801 AA R
" 3-R819 AA R
" 3-R1003 AA R
" 3-R1039 AA R
" 3-R3011 AA R
" 3-R3012 AA R
" 3-R3018 AA R
" 3-R3021 AA R
" 3-R3033 AA R
" 3-R3036 AA R
VRS-CY1JF103JY 3-R316 AA R
" 3-R373 AA R
" 3-R458 AA R
" 3-R520 AA R
" 3-R618 AA R
" 3-R810 AA R
" 3-R811 AA R
" 3-R835 AA R
" 3-R1018 AA R
" 3-R1030 AA R
VRS-CY1JF104JY 3-R372 AA R
" 3-R374 AA R
" 3-R1010 AA R
" 3-R1027 AA R
" 3-R1045 AA R
" 3-R3004 AA R
VRS-CY1JF105JY 3-R1041 AA R
" 3-R3003 AA R
VRS-CY1JF121JY 4-R876 AA R
" 4-R877 AA R
" 4-R878 AA R
VRS-CY1JF122JY 3-R206 AA R
VRS-CY1JF123JY 3-R617 AA R
VRS-CY1JF124JY 3-R807 AA R
" 3-R1802 AA R
VRS-CY1JF152JY 4-R891 AA R
" 4-R894 AA R
VRS-CY1JF181JY 3-R824 AA R
" 3-R826 AA R
" 3-R827 AA R
VRS-CY1JF182JY 3-R822 AA R
" 3-R832 AA R
" 3-R833 AA R
" 3-R834 AA R
" 3-R3031 AA R
" 3-R3034 AA R
VRS-CY1JF183JY 3-R1011 AA R
" 3-R1020 AA R
" 3-R1022 AA R
" 3-R1026 AA R
VRS-CY1JF220JY 3-R818 AA R
VRS-CY1JF221JY 3-R207 AA R
" 3-R220 AA R
VRS-CY1JF222JY 3-R307 AA R
" 3-R315 AA R
" 3-R504 AA R
" 3-R843 AA R
" 3-R1801 AA R
VRS-CY1JF223JY 3-R828 AA R
" 3-R3032 AA R
" 3-R3035 AA R
VRS-CY1JF271JY 4-R849 AA R
" 4-R854 AA R
" 4-R855 AA R
VRS-CY1JF274JY 3-R305 AA R
VRS-CY1JF302JY 3-R3008 AA R
VRS-CY1JF331JY 3-R208 AA R
" 3-R817 AA R
VRS-CY1JF332JY 3-R204 AA R
" 3-R362 AA R
" 3-R366 AA R
" 3-R1032 AA R
" 3-R1056 AA R
" 3-R1074 AA R
" 3-R3007 AA R
VRS-CY1JF391JY 4-R892 AA R
VRS-CY1JF392JY 3-R209 AA R
" 3-R3010 AA R
" 3-R3027 AA R
" 3-R3029 AA R
RANK
MARK
PART
RANK
21L-FG1L
PRICE
NEW
PARTS CODE No.
VRS-CY1JF470JY 3-R841 AA R
" 4-R850 AA R
" 4-R851 AA R
" 4-R852 AA R
VRS-CY1JF471JY 3-R816 AA R
" 3-R1042 AA R
VRS-CY1JF472JY 3-R823 AA R
" 3-R838 AA R
" 3-R1046 AA R
" 3-R1092 AA R
VRS-CY1JF473JY 3-R303 AA R
" 3-R802 AA R
" 3-R825 AA R
" 3-R829 AA R
" 3-R1044 AA R
" 3-R1894 AA R
" 3-R1895 AA R
" 3-R1896 AA R
VRS-CY1JF475JY 3-R1803 AA R
VRS-CY1JF562JY 3-R1038 AA R
VRS-CY1JF623JY 3-R3005 AA R
VRS-CY1JF680JY 3-R205 AA R
VRS-CY1JF683JY 3-R3028 AA R
" 3-R3030 AA R
VRS-CY1JF750JY 3-R461 AA R
VRS-CY1JF822JY 3-R806 AA R
" 3-R812 AA R
" 3-R1021 AA R
VRS-RG3AB331J+ 3-R506 AB R
VRS-RG3DB121J+ 3-R755 AB R
VRS-RG3LB391J+ 3-R631 R
VRS-RG3LB393J+ 3-R216 AC R
VRS-VV3DB124J 3-R702 AA R
VRS-VV3DB153J 4-R859 AA R
" 4-R861 AA R
" 4-R863 AA R
VRS-VV3DB682J 3-R622 AA R
VS2SA1530AR-1Y 3-Q802 AB R
" 3-Q805 AB R
" 4-Q894 AB R
VS2SC2235Y/1E+ 3-Q601 AE R
VS2SC2735//1EY 3-Q201 R
VS2SC3198-G-1+ 3-Q603 AA R
VS2SC3928AR-1Y 3-Q350 AB R
" 3-Q351 AB R
" 3-Q604 AB R
" 3-Q801 AB R
" 3-Q803 AB R
" 3-Q1001 AB R
" 3-Q1002 AB R
" 3-Q1801 AB R
" 3-Q3001 AB R
" 3-Q3002 AB R
" 3-Q3004 AB R
" 3-Q3005 AB R
VS2SD468-C/-1+ 3-Q751 AD R
" 3-Q752 AD R
" 3-Q753 AD R
" 3-Q754 AD R
VSP9050PA02WA 5-SP301 AH R
VSTT2140+++-F 3-Q602 AG R
RANK
MARK
PART
RANK
13
Page 58
21L-FG1L
14
Page 59
EndPage
COPYRIGHT
COPYRIGHT©XXXX BYSHARP CORPORATION
2007 BY SHARP CORPORATION
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
COPYRIGHT©XXXX BYSHARP CORPORATION
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
ALL RIGHTS RESERVED.
No part of this publication may be reproduced,
stored in a retrieval system, or transmitted in
any form or by any means, electronic, mechanical,
photocopying, recording, or otherwise, without
prior written permission of the publisher.
RQ0069-S
Jun 2007 Printed in Malaysia
Design and Production Information
Design :SREC
Production :SREC
CHS.SREC
SHARP-ROXY ELECTRONICS
CORPORATION (M) SDN. BHD
QRC DEPARTMENT
Batu Pahat, Johor, Malaysia
P.O.BOX 513
– 1
Loading...