SHARP 20LK60A, 20LK30A Service Manual

Download

Page 1

20LK30A/60A

SERVICE MANUAL

S49F420LK30A/

COLOR TELEVISION

Chassis No. SN-70A

20LK30A

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.

20LK60A

MODELS

20LK30A/60A

CONTENTS

Page

» ELECTRICAL SPECIFICATIONS......................................................................................................... 1

» IMPORTANT SERVICE SAFETY PRECAUTION ................................................................................2

» LOCATION OF USER'S CONTROL.....................................................................................................4

» INSTALLATION AND SERVICE INSTRUCTIONS ............................................................................... 5

» CHASSIS LAYOUT .............................................................................................................................11

» BLOCK DIAGRAM ............................................................................................................................. 13

» SCHEMATIC DIAGRAMS .................................................................................................................. 15

» PRINTED WIRING BOARD ASSEMBLIES........................................................................................22

» REPLACEMENT PARTS LIST ........................................................................................................... 25

» PACKING OF THE SET ..................................................................................................................... 31

ELECTRICAL SPECIFICATIONS

POWER INPUT .........................................110-220 V AC 50/60 Hz

POWER RATING

20LK30A .............................................................................88 W

20LK60A .............................................................................98 W

PICTURE SIZE ........................................... 1,194cm2 (185sq inch)

CONVERGENCE............................................................. Magnetic

SWEEP DEFLECTION .....................................................Magnetic

FOCUS ............................................... Hi-Bi-Potential Electrostatic

INTERMEDIATE FREQUENCIES

Picture IF Carrier Frequency ..................................... 45.75 MHz

Sound IF Carrier Frequency ......................................41.25 MHz

Color Sub-Carrier Frequency..................................... 42.17 MHz

(Nominal)

AUDIO POWER

OUTPUT RATING

20LK30A ............................................ 1.3W (at 10% distortion)

20LK60A ............................................ 2.5W (at 10% distortion)

SHARP CORPORATION

SPEAKER

SIZE ........................................................................ 9 cm × 5 cm

VOICE COIL IMPEDANCE

20LK30A .......................................................8 ohm at 400 Hz

20LK60A .....................................................16 ohm at 400 Hz

ANTENNA INPUT IMPEDANCE

VHF/UHF .................................................... 75 ohm Unbalanced

TUNING RANGES

VHF-Channels .............................................................. 2 thru 13

UHF-Channels ............................................................14 thru 69

CATV Channels ..........................................................1 thru 125

Specifications are subject to change without prior notice.

Page 2

20LK30A/60A

IMPORTANT SERVICE SAFETY PRECAUTION

Service work should be performed only by qualified service technicians who are throughly familiar with all safety checks and the servicing guidelines which follow:

WARNING

1. For continued safety, no modification of any circuit should be attempted.

2. Disconnect AC power before servicing.

3. Semiconductor heat sinks are potential shock hazards when the chassis is operating.

4. The chassis in this receiver has two ground systems which are separated by insulating material. The nonisolated (hot) ground system is for the B+ voltage regulator circuit and the horizontal output circuit. The isolated ground system is for the low B+ DC voltages and the secondary circuit of the high voltage transformer. To prevent electrical shock use an isolation transformer between the line cord and power receptacle, when servicing this chassis.

SERVICING OF HIGH VOLTAGE SYSTEM AND PICTURE TUBE

When servicing the high voltage system, remove the static charge by connecting a 10k ohm resistor in series with an insulated wire (such as a test probe) between the picture tube ground and the anode lead. (AC line cord should be disconnected from AC outlet.)

1. Picture tube in this receiver employs integral implosion protection.

2. Replace with tube of the same type number for continued safety.

3. Do not lift picture tube by the neck.

4. Handle the picture tube only when wearing shatterproof goggles and after discharging the high voltage anode completely.

X-RADIATION AND HIGH VOLTAGE LIMITS

1. Be sure all service personnel are aware of the procedures and instructions covering X-radiation. The only potential source of X-ray in current solid state TV receivers is the picture tube. However, the picture tube does not emit measurable X-Ray radiation, if the high voltage is as specified in the "High Voltage Check" instructions. It is only when high voltage is excessive that Xradiation is capable of penetrating the shell of the picture tube including the lead in the glass material. The important precaution is to keep the high voltage below the maximum level specified.

2. It is essential that servicemen have available at all times an accurate high voltage meter. The calibration of this meter should be checked periodically.

3. High voltage should always be kept at the rated value

−no higher. Operation at higher voltages may cause a failure of the picture tube or high voltage circuitry and;also, under certain conditions, may produce radiation in exceeding of desirable levels.

4. When the high voltage regulator is operating properly there is no possibility of an X-radiation problem. Every time a color chassis is serviced, the brightness should be tested while monitoring the high voltage with a meter to be certain that the high voltage does not exceed the specified value and that it is regulating correctly.

5. Do not use a picture tube other than that specified or make unrecommended circuit modifications to the high voltage circuitry.

6. When trouble shooting and taking test measurements on a receiver with excessive high voltage, avoid being unnecessarily close to the receiver. Do not operate the receiver longer than is necessary to locate the cause of excessive voltage.

Page 3

2 2

IMPORTANT SERVICE SAFETY PRECAUTION

1.5k ohm 10W

0.15µF

TEST PROBE

CONNECT TO KNOWN EARTH GROUND

TO EXPOSED METAL PARTS

VOLTMETER

(Continued)

20LK30A/60A

BEFORE RETURNING THE RECEIVER (Fire & Shock Hazard)

Before returning the receiver to the user, perform the following safety checks.

1. Inspect all lead dress to make certain that leads are not pinched or that hardware is not lodged between the chassis and other metal parts in the receiver.

2. Inspect all protective devices such as non-metallic control knobs, insulating materials, cabinet backs, adjustment and compartment covers or shields, isolation resistor-capacity networks, mechanical insulators, etc.

3. To be sure that no shock hazard exists, check for leakage current in the following manner.

• Plug the AC cord directly into a 1 10~220 volt AC outlet, (Do not use an isolation transformer for this test).

• Using two clip leads, connect a 1.5k ohm, 10 watt resistor paralleled by a 0.15µF capacitor in series with all exposed metal cabinet parts and a known earth ground, such as electrical conduit or electrical ground connected to earth ground.

• Use an AC voltmeter having with 5000 ohm per volt, or higher, sensitivity to measure the AC voltage drop across the resistor.

• Connect the resistor connection to all exposed metal parts having a return to the chassis (antenna, metal cabinet, screw heads, knobs and control shafts, escutcheon and etc.) and measure the AC voltage drop across the resistor. AII checks must be repeated with the AC ine cord plug connection reversed. (If necessary, a nonpolarized adapter plug must be used only for the purpose of completing these check.) Any current measured must not exceed 0.5 milliamp. Any measurements not within the limits outlined above indicate of a potential shock hazard and corrective action must be taken before returning the instrument to the customer.

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

SAFETY NOTICE

Many electrical and mechanical parts in television receivers have special safety-related characteristics. These characteristics are often not evident from visual inspection, nor can protection afforded by them be necessarily increased by using replacement components rated for higher voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this manual; electrical components having such features are identified by "å" and shaded areas in the Replacement Parts Lists and Schematic Diagrams.

234567890123456789012345678901212345678901234567890123456789012123456789012345678901234567890121

For continued protection, replacement parts must be identical to those used in the original circuit. The use of substitute replacement parts which do not have the same safety characteristics as the factory recommended replacement parts shown in this service manual, may create shock, fire, X-radiation or other hazards.

Page 4

20LK30A/60A

INSTALLATION AND SERVICE INSTRUCTIONS

Note: (1)When performing any adjustments to resistor controls and transformers use non-metallic

screwdrivers or TV alignment tools.

(2)Before performing adjustments, the TV set must be on at least 15 minutes.

CIRCUIT PROTECTION

The receiver is protected by a 3.15A fuse (F701), mounted on PWB-A, wired into one side of the AC line input.

X-RADIATION PROTECTOR CIRCUIT TEST

After service has been performed on the horizontal deflection system, high voltage system, B+ system, test the X-Radiation protection circuit to ascertain proper operation as follows:

1. Apply 220V AC using a variac transformer for accurate input voltage.

2. Allow for warm up and adjust all customer controls for normal picture and sound.

3. Receive a good local channel.

4. Connect a digital voltmeter to TP653 and make sure that the voltmeter reads 20.6 ± 1.5V.

5. Apply external 26.8V DC at TP653 by using an external DC supply, TV must be shut off.

6. To reset the protector, unplug the AC cord and make a short circuit between TP651 and TP652. Now make sure that normal picture appears on the screen.

7. If the operation of the horizontal oscillator does not stop in step 5, the circuit must be repaired before the set is returned to the customer.

HIGH VOLTAGE CHECK

High voltage is not adjustable but must be checked to verify that the receiver is operating within safe and efficient design limitations as specified checks should be as follows:

1. Connect an accurate high voltage meter between ground and anode of picture tube.

2. Operate receiver for at least 15 minutes at 110~220V AC line voltage, with a strong air signal or a properly tuned in test signal.

3. Enter the service mode and select the service adjustment "S19" and Bus data "01" (Y-mute on).

4. The voltage should be approximately, 26.5kV (at zero beam). If a correct reading cannot be obtained, check circuitry for malfunctioning components. After the voltage test, make Y-mute off to the normal mode.

Page 5

20LK30A/60A

For adjustments of this model, the bus data is converted to various analog signals by the D/A converter circuit.

Note: There are still a few analog adjustments in this series such as focus and master screen voltage.

Follow the steps below whenever the service adjustment is required. See "Table-B" to determine, if service adjustments are required.

1. Service mode

Before putting unit into the service mode, check that customer adjustments are in the normal mode. Use the reset function in the video adjustment menu to ensure customer controls are in their proper (reset) position.

2. Service number selection

Once in the service mode, press the Ch-up or Chdown button on the remote controller or at the set. The service adjustment number will vary in increments of one, from "S01" to "M05". Select the item you wish to adjust.

3. Data number selection

Press the Vol-up or down button to adjust the data number.

DATA NUMBER (HEX) (HEXADEC: MAL)

SERVICE ADJUSTMENT NUMBER

To enter the service mode and exit service mode.

While pressing the Vol-up and Ch-up buttons at the sametime, plug the AC cord into a wall socket. Now the TV set is switched on and enters the service mode. To exit the service mode, turn the television off by pressing the power button.

CHANNEL

S01

Figure A.

S01 D:00

Page 6

20LK30A/60A

SERVICE

NUMBER

S01 PICTURE 55 00-7F S02 TINT 46 00-7F S03 COLOR 32 00-7F S04 BRIGHTNESS 40 00-7F S05 SHARPNESS 28 00-3F Must be set to "24" S06 VERTICAL PHASE 00 00-07 Must be set between "0" to "03" S07 HORIZONTAL PHASE 12 00-1F S08 RF-AGC 2A 00-3F S09 VERTICAL AMP 20 00-3F S10 VCO 2C 00-7F S11 R CUT-OFF 00 00-FF S12 G CUT -OFF 00 00-FF S13 B CUT-OFF 00 00-FF S14 G GAIN 7F 00-FF S15 B GAIN 7F 00-FF S16 TRAP(3.58MHz) 00 00 or 01 Must be set to "00" S17 BALANCE 20 00-3F Must be set to "20" S18 C.C.POSITION 18 00-7F S19 Y-MUTE 00 00,01,03 "00"=Normal, "01"=No-Y, "03"=No Vertical OP. OPTION (Set to each model) 80 00-FF Must be set to "08"=20LK30A, "09"=20LK60A M01 MTS LEVEL 0A 00-0F M02 STEREO-VCO 20 00-3F M03 FILTER 1C 00-3F M04 LOW SEPARATION 20 00-3F M05 HIGH SEPARATION 1B 00-3F

ADJUSTMENT ITEM

INITIAL VALUE

DATA

ADJUSTMENT CONTENTS

RANGE

Table - A

Holding down both the CH-up/down buttons on the TV set at service mode for more than 2 seconds will automatically write the above initial values into IC2101.

PART REPLACED

IC2001

IC201 X

IC2101

CRT IC3001

(20LK60A)

ADJUSTMENT

NECESSARY

X X

UNNECESSARY

Data is stored in IC2101.

The adjustment is needed to compensate for characteristics of parts including IC201.

Holding down both the CH-up/down buttons on the TV set in the service mode for more than 2 seconds will automatically write the above initial values into IC2101.

Adjust items related to picture tube only.

Adjust items related to MTS only (M01~M05).

NOTES

Table - B

Page 7

20LK30A/60A

SERVICE ADJUSTMENT

VCO Adjustment

1. Connect a digital voltmeter between pin (44) of IC201 and ground.

2. Receive a good local channel.

3. Enter the service mode and select the service adjustment "S10".

4. Adjust the data so that digital voltmeter reads 2.2V.

5. Adjustment is completed, remove the voltmeter, return to "normal" mode.

RF AGC Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S08".

3. Set the data value to point where no noise or beat appears.

4. Select another channel to confirm that no noise or beat appears. Note 1 : You will have to come out of the service

mode to select another channel.

Note 2 : Setting the data to "00" will produce a black

raster.

Screen Adjustment

1. Connect a digital voltmeter between TP852 and TP853 on the CRT socket PWB. Note : These test points may not be provided.

Then connect the voltmeter to both ends of R852 located near Q852 on the foil side.

2. Receive a good local channel.

3. Enter the service mode and select the service adjustment "S03" and set the data value to "00" to set the color level to minimum. (Record original data code under adjustment "S03" before changing) You may skip this step, if you selected a B/W picture or monoscope pattern.

4. Select the service adjustment "S19" and adjust the data value to "01", this turn off the luminance signal (Y-mute).

5. Select the service adjustment "S04" and adjust data value to obtain 0.17 volts on the oscilloscope screen.

6. Adjust the master screen control until the raster darkens to the point where raster is barely seen.

7. Adjust the service adjustments "S11" red, "S12" green and "S13" blue to obtain a good grey scale with normal whites at low brightness level.

8. Select the service adjustment "S19" and reset data to "00". Select the service adjustment "S03" and reset data to obtain normal color level.

9. Remove digital voltmeter, and reset the master screen control to obtain normal brightness range.

White Balance Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S03" and set to "00" (minimum color). "S03" does not have to be adjusted, if you selected a B/W picture or monoscope pattern.

3. Alternately adjust the service adjustment data of "S14" and "S15" until a good grey scale with normal whites is obtained.

4. Select the service adjustment "S03" and adjust data to obtain normal color level.

Sub-Picture Adjustment

1. Receive a good local channel.

2. Make sure the customer picture control is set to maximum.

3. Enter the service mode and select the service adjustment "S01".

4. Adjust the data value to achieve normal contrast range.

Sub-Tint Adjustment

1. Receive a good local channel.

2. Set customer tint control to center of it's range.

3. Enter the service mode and select the service adjustment "S02".

4. Adjust "S02" data value to obtain normal flesh tones.

+115V DC REGULATOR Adjustment

The +115V DC Adj. control (R721) is adjusted at the factory . However, should readjustment be required, proceed as follows:

1. Actuate the receiver with 220V AC input voltage.

2. Select a local channel.

3. Connect positive lead of Digital Voltmeter to R603 TP751 (positive side) on PWB-A; negative lead to chassis ground.

4. Adjust R721 to obtain a +115V DC reading.

CAUTION: The reading should be within +1 15V ±1VDC

to ensure normal function and circuitry reliability.

Page 8

20LK30A/60A

Sub-Color Adjustment

1. Receive a good local channel.

2. Make sure the customer color control is set to center position .

3. Enter the service mode and select the service adjustment "S03".

4. Adjust "S03" data value to obtain normal color level.

Sub-Brightness Adjustment

1. Receive a good local channel.

2. Make sure the customer brightness control is set to center position.

3. Enter the service mode and select the service adjustment "S04".

4. Adjust "S04" data value to obtain normal brightness level.

Vertical-Size Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S09".

3. While observing the top and bottom of the screen, adjust "S09" data value to proper vertical size.

Vertical Phase Adjustment

1. Enter the service mode and select the service adjustment "S06".

2. Adjust data value to "00" ~ "03" so that picture is approximate center. Note: This must be set "00" ~ "03" when adjust

another data retrace line will be appear.

Horizontal Position Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S07".

3. Adjust "S07" data value so that picture is centered.

Caption Position Adjustment (Horizontal)

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S18".

3. A black text box appears on the screen. (see Figure B. below)

4. Adjust "S18" data value so that text box is positioned in the center of the screen.

3.58MHz Trap Adjustment

1. Receive a good local channel.

2. Enter the service mode and select the service adjustment "S16".

3. This is a two position adjustment, "00" is ON, "01" is OFF.

4. Adjust data value to "00" for normal viewing.

Sharpness and Audio Balance Adjustments

1. Receive a good local channel.

2. Enter the service mode and select the service adjustments "S05" for sharpness and "S17" for balance.

» Sharpness Adjustment

3. Adjust data value to "24"(center of data range) for sharpness adjustment.

» Audio Balance Adjustment

4. Adjust data value to "20"(center of data range) for audio balance adjustment.

Figure B.

Page 9

20LK30A/60A

MTS ADJUSTMENT

(Only for 20LK60A)

MTS Level Adjustment

1. Feed the following monaural signal to pin (14) of IC3001.

Monaural signal : 300Hz, 245mVrms

2. Connect the rms voltmeter to pin (39) of IC3001.

3. Enter the service mode and select the service adjustment "M01".

4. Adjust the data so that the rms voltmeter reads.

Spec.: 490 ±10mVrms.

MTS VCO Adjustment

1. Keep the unit in no-signal state.

2. Connect the frequency counter to pin (39) of IC3001.

3. Connect a capacitor (100µF, 50V) in between positive(+) side of C3005 and ground.

4. Enter the service mode and select the service adjustment "M02"

5. Adjust the data so that the frequency counter reads.

Spec.: 62.94 ±0.75kHz.

Filter Adjustment

1. Feed the following stereo pilot signal to pin (14) of IC3001 . Stereo pilot signal: 9.4kHz, 600mVrms.

2. Enter the service mode and select the service adjustment "M03".

3. Adjust the data at the point where "OK" appears on the screen. The "OK" represents the approximate center of the adjustable range of the data.

Separation Adjustment

1. Connect the rms voltmeter to pin (39) of IC3001.

2. Receive the following composite stereo signal 1. Composite stereo signal: 30% modulation, left channel only, noise reduction on, 300Hz

3. Enter the service mode and select the service adjustment "M04".

4. Adjust the data until the AC voltage reading of the rms voltmeter is minimum.

5. Receive the following composite stereo signal 2. Stereo signal: 30% modulation, left channel only, noise reduction on, 3kHz

6. Enter the service mode and select the service adjustment "M05".

7. Adjust the data until the AC voltage reading of the rms voltmeter is minimum.

8. Take the above steps 1 thru 8 again for fine adjustment.

Page 10

MODEL 20LK30A CHASSIS LAYOUT

20LK30A/60A

PWB-B

PWB-C

PWB-A

654321

Page 11

20LK30A/60A

MODEL 20LK60A CHASSIS LAYOUT

PWB-B

PWB-C

PWB-A

654321

Page 12

MODEL 20LK30A BLOCK DIAGRAM

20LK30A/60A

654321

Page 13

20LK30A/60A

MODEL 20LK60A BLOCK DIAGRAM

654321

Page 14

DESCRIPTION OF SCHEMATIC DIAGRAM

20LK30A/60A

NOTES:

1. The unit of resistance "ohm" is omitted. (K=kΩ=1000Ω, M=MΩ)

2. All resistors are 1/16 watt, unless otherwise noted.

3. All capacitors are µ F, unless otherwise noted. (P=pF=µµF)

4. (G) indicates ±2% tolerance may be used.

5. indicates line isolated ground.

6. indicates hot ground.

VOLTAGE MEASUREMENT CONDITIONS:

1. All DC voltages are measured with DVM connected between points indicated and chassis ground, line voltage set at 110~220V AC and all controls set for normal picture unless otherwise indicated.

2. All voltages measured with 1000µ V B & W or Color

signal.

WAVEFORMS

WAVEFORM MEASUREMENT CONDITIONS:

1. Photographs taken on a standard gated color bar signal, the tint setting adjusted for proper color. The wave shapes at the red, green and blue cathodes of the picture tube depend on the tint, color level and picture control.

indicates waveform check points (See chart, waveforms are measured from point indicated to chassis ground.)

AND SHADED ( ) COMPONENTS = SAFETY RELATED PARTS.

MARK= X-RAY RELATED PARTS.

This circuit diagram is a standard one, printed circuits may be subject to change for product improvement without prior notice.

654321

Page 15

20LK30A/60A

MODEL 20LK30A SCHEMATIC DIAGRAM : MAIN Unit

87109654321

654321

Page 16

20LK30A/60A

1716 1918151413121110

654321

Page 17

20LK30A/60A

MODEL 20LK60A SCHEMATIC DIAGRAM : MAIN-1 Unit

87109654321

654321

Page 18

20LK30A/60A

1716 1918151413121110

654321

Page 19

20LK30A/60A

MODEL 20LK60A SCHEMATIC DIAGRAM : MAIN-2 Unit

654321

Page 20

SCHEMATIC DIAGRAM : FRONT AV and CRT Unit

20LK30A/60A

20LK30A

20LK60A

654321

Page 21

20LK30A/60A

PRINTED WIRING BOARD ASSEMBLIES

PWB-A: MAIN Unit (Wiring Side)

654321

Page 22

20LK30A/60A

PWB-A: MAIN Unit (Chip Parts Side)

654321

Page 23

20LK30A/60A

PWB-B: CRT Unit (Wiring Side)

PWB-C: FRONT AV Unit (Wiring Side)

654321

Page 24

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PARTS LIST

PWB-A: DUNTK9731WEV1(20LK30A)

PARTS REPLACEMENT

Replacement parts which have these special safety characteristics identified in this manual; electrical components having such features are identified by å and shaded areas in the Replacement Parts Lists and Schematic Diagrams. The use of a substitute replacement part which dose no have the same safety characteristic as the factory recommended replacement parts shown in this service manual may create shock, fire or other hazards.

"HOW TO ORDER REPLACEMENT PARTS"

To have your order filled promptly and correctly, please furnish the following informations.

1. MODEL NUMBER 2. REF. NO.

3. PART NO. 4. DESCRIPTION

★MARK : SPARE PARTS-DELIVERY SECTION

'MARK : X- RAY RELATED PARTS

Ref. No. Part No. ★ Description Code

PWB-A: DUNTK9731WEV2(20LK60A)

MAIN UNIT

TUNER

NOTE : THE PARTS HERE SHOWN ARE SUPPLIED AS AN

ASSEMBLY BUT NOT INDEPENDENTLY.

å TU51 VTU115B8025AM J VHF Tuner

INTEGRATED CIRCUITS

IC101 VHiKA78S05P-1 J KA78S05P AD

å IC201 RH-iX2701CEN1 J TA1201CN (20LK60A) AY

çå IC201 RH-iX2933CEZZ J TA1268N (20LK30A) AX

IC351 VHiTDA7056A-1 J TDA7056A AP IC352 VHiTDA7056A-1 J TDA7056A (20LK60A) AP

å IC501 VHiTA8403K/-1 J TA8403K AL å IC701 RH-iX1779CEZZ J TEA2261 AR å IC751 VHiKA7809Pi-1 R KA7809PI AE

VHiTA7809S/-1 IC2001 RH-iX2946CEZZ J TMPA8701CKF108 AX IC2040 VHiPST994C/-1 J PST994C AD IC2101 VHiM24C01B/-1 J M24C01-BN6 AF

RH-iX2447CEN1 IC3001 VHiCXA2053Q-1 J CXA2053Q (20LK60A) AX

PICTURE TUBE

çå V101 VB48KRD89X/3E R Picture Tube çå DY601 RCiLH0001GJZZ X Deflection Yoke

å L702 RCiLG0038PEZZ R Degaussing Coil AU

MSPRT0002MEZZ M Spring AA PMAGF3003CEZZ J Magnet AK

PRINTED WIRING BOARD ASSEMBLIES

(NOT REPLACEMENT ITEM)

PWB-A DUNTK9731WEV1 – Main Unit (20LK30A) — PWB-A DUNTK9731WEV2 – Main Unit (20LK60A) — PWB-B DUNTK9432WEV5 – CRT Unit — PWB-CDUNTK9732WEV0 – Front AV Unit (20LK30A) — PWB-CDUNTK9732WEV2 – Front AV Unit (20LK60A) —

TRANSISTORS

You can substitute "VS2SC2462-C-1" for "VS2SD601AR/-1". Q201 VS2SC2735//1E J 2SC2735 AC Q301 VS2SD601AR/-1 J 2SD601AR (20LK60A) AC Q351 VS2SC2462-C-1 J 2SC2462(C) AB Q352 VS2SC2462-C-1 J 2SC2462(C) (20LK60A) AB Q401 VS2SD601AR/-1 J 2SD601AR AC Q402 VS2SB709AR/-1 J 2SB709AR AC Q403 VS2SD601AR/-1 J 2SD601AR AC Q404 VS2SB709AR/-1 J 2SB709AR AC Q451 VS2SB709AR/-1 J 2SB709AR AC Q601 VS2SC2482//-1 J 2SC2482 AD

å Q602 VS2SD2586//1E J 2SD2586 AM å Q701 VS2SD1884//-1 J 2SD1884 AN

Q730 VS2SC1983//-2 J 2SC1983 (20LK60A) AF Q752 VS2SC1815YW-1 J 2SC1815YW AC Q753 VS2SC1815YW-1 J 2SC1815YW AC Q2001 VS2SD601AR/-1 J 2SD601AR AC Q2002 VS2SD601AR/-1 J 2SD601AR AC Q2060 VS2SC2462-C-1 J 2SC2462(C) AB

DIODES

D51 RH-EX0611GEZZ J Zener Diode, 5.0V AA D52 RH-EX0676GEZZ J Zener Diode, 32V AA D103 VHD1SS119//-1 J Diode AB D401 VHD1SS119//-1 J Diode AB D402 RH-EX0092CEZZ J Zener Diode, 3.9V AB D454 RH-EX0103CEZZ J Zener Diode, 5.6V AB D455 VHD1SS119//-1 J Diode AB D501 RH-DX0441CEZZ J Diode AC

or RH-DX0110CEZZ

å D502 RH-DX0131CEZZ J Diode AC

D603 RH-DX0441CEZZ J Diode AC

RH-DX0110CEZZ D604 VHD1SS119//-1 J Diode AB D605 VHD1SS119//-1 J Diode AB D631 RH-EX0630GEZZ J Zener Diode, 9.1V AA D641 RH-EX0631GEZZ J Zener Diode, 9.1V AA

çå D651 RH-DX0131CEZZ J Diode AC çå D652 VHD1SS119//-1 J Diode AB çå D653 RH-EX0091CEZZ J Zener Diode, 22V AB

å D661 RH-DX0444CEZZ J Diode AH å D701 RH-DX0055TAZZ J Diode AD å D702 RH-DX0055TAZZ J Diode AD å D703 RH-DX0055TAZZ J Diode AD

Page 25

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK9731WEV1(20LK30A) PWB-A: DUNTK9731WEV2(20LK60A)

MAIN UNIT (Continued)

å D704 RH-DX0055TAZZ J Diode AD

D705 RH-DX0302CEZZ J Diode AC D706 RH-DX0130CEZZ J Diode AE D707 RH-DX0130CEZZ J Diode AE D708 RH-EX0647GEZZ J Zener Diode, 1.5V AA D709 RH-DX0027CEZZ J Diode AE D710 RH-EX0914CEZZ J Zener Diode, 3.9V AD D711 RH-DX0130CEZZ J Diode AE D712 VHD1SS119//-1 J Diode AB D731 RH-EX0638GEZZ J Zener Diode, 11V(20LK60A) AB D732 RH-DX0441CEZZ J Diode (20LK60A) AC

å D751 RH-DX0388CEZZ J Diode AE å D752 RH-DX0224CEZZ J Diode (20LK30A) AB å D753 RH-DX0461CEZZ J Diode (20LK60A) AG

D754 VHD1SS119//-1 J Diode AB D755 VHD1SS119//-1 J Diode AB

å D758 RH-DX0131CEZZ J Diode AC

D2001 VHD1SS119//-1 J Diode AB

å VA701 RH-VX0048CEZZ J Varistor AE

P ACKAGED CIRCUITS

å PR701 RMPTP0062CEZZ J Packaged Circuit AH

X801 RCRSB0001PEZZ R Crystal AL

or RCRSB0205CEZZ

FILTERS

CF301 RFiLC0403CEZZ J Ceramic Filter AE

RFiLC0029TAZZ CF302 RFiLC0404CEZZ J Ceramic Filter (20LK60A) AF CF401 RFiLC0013CEZZ J Ceramic Filter AE

RFiLC0004PEZZ CF631 RFiLA0034CEZZ J Ceramic Filter AD CF2040

RFiLC0121GEZZ J Ceramic Filter AD SF201 RFiLC0405CEZZ J SAW Filter AH

COILS

L201 VP-XF1R2K0000 J Peaking 1.2µH AB L202 RCiLi0612CEZZ J IF Coil AE

RCiLi0588CEZZ L301 VP-XF8R2K0000 J Peaking 8.2µH AB L302 RCiLi0613CEZZ J VCO Coil AE

RCiLi0605CEZZ L401 VP-XF6R8K0000 J Peaking 6.8µH AB L402 VP-XF3R3K0000 J Peaking 3.3µH AB L403 VP-XF100K0000 J Peaking 10µH AB L404 VP-XF8R2K0000 J Peaking 8.2µH AB L406 VP-XF680K0000 J Peaking 68µH AB L409 VP-XF100K0000 J Peaking 10µH AB

å L701 RCiLF0012PEZZ R Coil AN

L703 VP-CF100K0000 J Peaking 10µH AB L704 VP-CF3R3K0000 J Peaking 3.3µH AB L751 RCiLP0225CEZZ J Coil AF L2040 RCiLB0159CEZZ J Oscillation Coil AE

TRANSFORMERS

å T601 RTRNZ0367CEZZ J Transformer AK

çå T602 RTRNF0147PEZZ R H-Volt Transformer BC

å T701 RTRNZ0120PEZZ R Transformer AX

CONTROL

çå R721 RVR-M4324CEZZ J 220(B) 115V Adj. AC

CAPACITORS

[EL.··· Electrolytic, M-Poly.··· Metalized Polypro Film]

C51 VCEA0A1CW476M J 47 16V EL. AB

C52 VCSATA1CE226K J 22 16V Tantalum AD C53 VCEA0A1HW105M J 1.0 50V EL. AB C54 VCEA0A1HW225M J 2.2 50V EL. AB C55 VCEAGA1CW108M J 1000 16V EL. AD C102 VCEAGA1CW108M J 1000 16V EL. AD C201 VCKYCY1HF103Z J 0.01 50V Ceramic AA C202 VCKYPA1HF103Z J 0.01 50V Ceramic AA C203 VCKYCY1HF103Z J 0.01 50V Ceramic AA C204 VCKYCY1HF103Z J 0.01 50V Ceramic AA C205 VCEA0A1HW474M J 0.47 50V EL. AB C206 VCEA0A1CW227M J 220 16V EL. AC C207 VCKYCY1HF103Z J 0.01 50V Ceramic AA C208 VCEA0A1HW474M J 0.47 50V EL. AB C209 VCKYCY1HB222K J 2200p 50V Ceramic AA C210 VCKYCY1HB102K J 1000p 50V Ceramic AA C302 VCCCCY1HH330J J 33p 50V Ceramic AA C303 VCCCCY1HH390J J 39p 50V Ceramic AA

C303 VCKYCY1HB472K J 4700p 50V Ceramic AA C304 VCEA0A1HW225M J 2.2 50V EL.

C305 VCKYPA1HB151K J 150p 50V Ceramic AA C306 VCKYPA1HF103Z J 0.01 50V Ceramic AA C307 VCEA0A1CW477M J 470 16V EL. AC C308 VCKYCY1HB102K J 1000p 50V Ceramic AA C309 VCEA0A1CW227M J 220 16V EL. AC C312 VCKYCY1EF104Z J 0.1 25V Ceramic AA C351 VCQYTA1HM823K J 0.082 50V Mylar AB C352 VCKYCY1HB182K J 1800p 50V Ceramic AA C353 VCEAGA1CW108M J 1000 16V EL. AD C354 VCEA0A1CW106M J 10 16V EL. AB C355 VCQYTA1HM104K J 0.1 50V Mylar AC C356 VCQYTA1HM823K J 0.082 50V Mylar AB

C357 VCKYCY1HB182K J 1800p 50V Ceramic AA C358 VCEA0A1CW106M J 10 16V EL.

C359 VCEAGA1CW108M J 1000 16V EL. C360 VCQYTA1HM104K J 0.1 50V Mylar AC

C402 VCCCCY1HH331J J 330p 50V Ceramic AA C403 VCCCCY1HH101J J 100p 50V Ceramic AA C405 VCEA0A1HW335M J 3.3 50V EL. AB C406 VCEA0A1HW335M J 3.3 50V EL. AB C408 VCEA0A1CW106M J 10 16V EL. AB C409 VCEA0A1HW105M J 1.0 50V EL. AB C410 VCKYCY1EF104Z J 0.1 25V Ceramic AA C411 VCEAGA1CW108M J 1000 16V EL. AD C413 VCKYCY1HF103Z J 0.01 50V Ceramic AA C414 VCKYCY1EF104Z J 0.1 25V Ceramic AA C419 VCCCCY1HH330J J 33p 50V Ceramic AA C420 VCCCCY1HH471J J 470p 50V Ceramic AA C451 VCQYTA1HM563K J 0.056 50V Mylar AB C454 VCEA0A1HW475M J 4.7 50V EL. AB C502 VCEA0A1EW477M J 470 25V EL. AD C504 VCKYPA2HB391K J 390p 500V Ceramic AA C505 VCQYTA1HM473K J 0.047 50V Mylar AB C507 VCQYTA1HM103K J 0.01 50V Mylar AB C508 VCEAGA1VW107M J 100 35V EL. AC C509 VCKYPA2HB102K J 1000p 500V Ceramic AA C510 VCEAGA1VW477M J 470 35V EL. AD C511 VCQYTA1HM473K J 0.047 50V Mylar AB C513 VCEACA1HC225M J 2.2 50V EL. AC C514 VCEACA1HC225J J 2.2 50V EL. AC C517 VCKYPA1HB102K J 1000p 50V Ceramic AA C522 VCKYCY1HF103Z J 0.01 50V Ceramic AA C551 VCSATA1CE225K J 2.2 16V Tantalum AB C552 VCEA0A1HW225M J 2.2 50V EL. AB C603 VCKYPB2HB562K J 5600p 500V Ceramic AB

å C604 VCEAGH2CW227M J 220 160V EL. AH

çå C608 VCFPPD3CA922H J 9200p 1.6kV M-Poly. AF

C609 VCKYPA2HB222K J 2200p 500V Ceramic AA C612 VCFPPJ2EB474J J 0.47 250V M-Poly. AF C631 VCEA0A1HW225M J 2.2 50V EL. AB C632 VCKYCY1HF103Z J 0.01 50V Ceramic AA C633 VCEA0A1HW105M J 1.0 50V EL. AB

(20LK60A) (20LK30A)

(20LK60A) (20LK60A)

(20LK60A)

(20LK30A)

(20LK60A) (20LK60A)

AB AD

Page 26

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK9731WEV1(20LK30A) PWB-A: DUNTK9731WEV2(20LK60A)

MAIN UNIT (Continued)

C652 VCEA0A1HW475M J 4.7 50V EL. AB C653 VCEA0A1CW106M J 10 16V EL. AB C661 VCKYPA2HB152K J 1500p 500V Ceramic AA C662 VCEA0A1CW477M J 470 16V EL. AC

å C701 RC-FZ015SCEZZ J 0.047

or RC-FZ002SCEZZ or RC-FZ027CUMZZ or

RC-FZ059SCEZZ C703 RC-KZ0029CEZZ J 0.01 C704 RC-KZ0029CEZZ J 0.01 C705 RC-KZ0029CEZZ J 0.01

å C706 RC-EZ0693CEZZ J 220 400V EL. AS

C707 VCKYPA2HB102K J 1000p 500V Ceramic AA C708 RC-KZ0029CEZZ J 0.01 C709 VCKYPA2HB102K J 1000p 500V Ceramic AA C710 VCKYPA2HB472K J 4700p 500V Ceramic AB C711 RC-KZ0341CEZZ J 1000p 2kV Ceramic AD C712 RC-KZ0029CEZZ J 0.01 C713 RC-KZ0029CEZZ J 0.01 C714 VCEA0A1CW477M J 470 16V EL. AC C715 VCFYHA1HA474J J 0.47 50V Mylar AD C716 VCEA0A1HW106M J 10 50V EL. AB C717 VCFYHA1HA684J J 0.68 50V Mylar AD C718 RC-QZA471TAYJ J 470p 50V Mylar AB C719 VCEA0A1CW107M J 100 16V EL. AC C720 VCEAGA1JW476M J 47 63V EL. AB C721 VCFYHA1HA394J J 0.39 50V Mylar AC C722 VCKYPA1HB272K J 2700p 50V Ceramic AA C723 VCKYPA2HB102K J 1000p 500V Ceramic AA C724 VCEA0A1HW105M J 1.0 50V EL. AB C725 VCQYTA1HM563K J 0.056 50V Mylar AB

å C730 RC-KZ0311CEZZ J 0.0033

RC-KZ0215CEZZ

å C751 VCEAGH2CW107M J 100 160V EL. AE

C752 RC-KZ0341CEZZ J 0.001 2kV Ceramic AD C754 VCKYPA2HB102K J 1000p 500V Ceramic AA C755 VCEA0A1CW477M J 470 16V EL. AC C757 RC-KZ0341CEZZ J 0.001 2kV Ceramic AD C758 VCEAGA2EW106M J 10 250V EL. AC C759 VCKYPA2HB102K J 1000p 500V Ceramic AA C760 VCEA0A1CW337M J 330 16V EL. AC C761 VCQYTA1HM104K J 0.1 50V Mylar AC C801 RC-QZA223TAYK J 0.022 50V Mylar AB C802 VCEA0A1HW474M J 0.47 50V EL. AB C803 VCCCCY1HH120J J 12p 50V Ceramic AA C804 VCEA0A1HW104M J 0.1 50V EL. AB C805 VCEA0A1HW104M J 0.1 50V EL. AB C806 VCEA0A1HW104M J 0.1 50V EL. AB C807 VCCCCY1HH820J J 82p 50V Ceramic AA C901 VCKYCY1EF104Z J 0.1 25V Ceramic AA C904 VCEA0A1HW335M J 3.3 50V EL. C905 VCEA0A1HW335M J 3.3 50V EL. AB C2001 VCCCCY1HH101J J 100p 50V Ceramic AA C2002 VCCCCY1HH101J J 100p 50V Ceramic AA C2003 VCEA0A1CW106M J 10 16V EL. AB C2021 VCCCCY1HH101J J 100p 50V Ceramic AA C2022 VCCCCY1HH101J J 100p 50V Ceramic AA C2023 VCCCCY1HH101J J 100p 50V Ceramic AA C2024 VCCCCY1HH101J J 100p 50V Ceramic AA C2040 VCEA0A1AW107M J 100 10V EL. AB C2041 VCEA0A1HW105M J 1.0 50V EL. AB C2060 VCQYTA1HM104K J 0.1 50V Mylar AC C2061 VCCCPA1HH101J J 100p 50V Ceramic AA C2062 VCEA0A1AW107M J 100 10V EL. AB C2401 VCCCPA1HH560J J 56p 50V Ceramic AA C2402 VCCCPA1HH560J J 56p 50V Ceramic AA C2601 VCEA0A1CW476M J 47 16V EL. AB C2602 VCCCCY1HH101J J 100p 50V Ceramic AA

AC250V

Plastic AE

AC250V

Ceramic AC

AC250V

Ceramic AC

AC250V

Ceramic AC

AC250V

Ceramic AC

AC250V

Ceramic AC

AC250V

Ceramic AC

AC250V

Ceramic AD

(20LK60A)

C3001 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3002 VCKYCY1HB562K J 5600p 50V Ceramic AA C3003 RC-QZA123TAYK J 0.012 50V Mylar AB C3004 VCEA0A1HW105M J 1.0 50V EL.

C3005 VCEA0A1HW475M J 4.7 50V EL. C3006 VCEA0A1HW106M J 10 50V EL. C3007 VCEA0A1HW475M J 4.7 50V EL. C3008 VCKYCY1HF103Z J 0.01 50V Ceramic AA

C3009 VCEA0A1CW227M J 220 16V EL. C3010 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB

C3011 VCEA0A1HW475M J 4.7 50V EL. C3012 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB

C3013 VCKYCY1HB272K J 2700p 50V Ceramic AA C3014 RC-QZA473TAYK J 0.047 50V Mylar AB C3015 VCSATA1CE335K J 3.3 16V Tantalum AC C3016 VCE9GA1HW475M J 4.7 50V EL.(N.P) AB C3017 VCSATA1CE106K J 10 16V Tantalum AD C3018 VCEA0A1HW105M J 1.0 50V EL.

C3019 VCEA0A1HW475M J 4.7 50V EL. C3020 VCEA0A1HW475M J 4.7 50V EL.

(20LK60A) (20LK60A) (20LK60A)

(20LK60A)

(20LK60A) (20LK60A) (20LK60A) (20LK60A) (20LK60A) (20LK60A)

(20LK60A) (20LK60A) (20LK60A) (20LK60A)

(20LK60A)

(20LK60A) (20LK60A) (20LK60A)

AB AB AB AB

AB AB AB

RESISTORS

RJ1 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ2 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ4 VRS-CY1JF000J J 0 1/16W M-Ox. AA

RJ5 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ6 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ7 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ8 VRS-CY1JF000J J 0 1/16W M-Ox. AA

RJ11 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ12 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ13 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ15 VRS-CY1JF000J J 0 1/16W M-Ox. AA

RJ16 VRS-CY1JF000J J 0 1/16W M-Ox. AA RJ17 VRS-CY1JF000J J 0 1/16W M-Ox. AA

å R51 VRS-VV3DB151J J 150 2W M-Ox. AA

R52 VRD-RA2BE1R0J J 1.0 1/8W Carbon AA

å R53 VRS-VV3LB223J J 22k 3.0W M-Ox. AB

R54 VRS-CY1JF101J J 100 1/16W M-Ox. AA R55 VRS-CY1JF101J J 100 1/16W M-Ox. AA R56 VRS-CY1JF823J J 82k 1/16W M-Ox. AA R57 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R201 VRS-CY1JF221J J 220 1/16W M-Ox. AA R202 VRS-CY1JF122J J 1.2k 1/16W M-Ox. AA R203 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R204 VRS-CY1JF270J J 27 1/16W M-Ox. AA R205 VRS-CY1JF391J J 390 1/16W M-Ox. AA R206 VRD-RA2EE151J J 150 1/4W Carbon AA R208 VRS-CY1JF391J J 390 1/16W M-Ox. AA R301 VRD-RA2BE222J J 2.2k 1/8W Carbon AA R302 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R303 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R304 VRS-CY1JF333J J 33k 1/16W M-Ox. AA

R305 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA

[M-Ox.··· Metal Oxide, M-Film··· Metal Film]

(20LK60A)

(20LK30A) (20LK60A) (20LK60A) (20LK60A)

(20LK60A) (20LK60A)

Page 27

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK9731WEV1(20LK30A) PWB-A: DUNTK9731WEV2(20LK60A)

MAIN UNIT (Continued)

R306 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA

(20LK60A) R351 VRD-RA2BE153J J 15k 1/8W Carbon AA R352 VRD-RA2BE4R7J J 4.7 1/8W Carbon AA R353 VRD-RA2BE153J J 15k 1/8W Carbon AA

(20LK60A) R354 VRD-RA2BE4R7J J 4.7 1/8W Carbon AA

(20LK60A) R355 VRD-RA2BE333J J 33k 1/8W Carbon AA R401 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R403 VRS-CY1JF331J J 330 1/16W M-Ox. AA R404 VRS-CY1JF391J J 390 1/16W M-Ox. AA R405 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R406 VRS-CY1JF470J J 47 1/16W M-Ox. AA R407 VRS-CY1JF680J J 68 1/16W M-Ox. AA R408 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R409 VRS-CY1JF471J J 470 1/16W M-Ox. AA R410 VRD-RA2BE563J J 56k 1/8W Carbon AA R411 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R412 VRD-RA2EE561J J 560 1/4W Carbon AA R413 VRD-RA2BE470J J 47 1/8W Carbon AA R414 VRD-RA2BE470J J 47 1/8W Carbon AA R415 VRD-RA2BE470J J 47 1/8W Carbon AA R416 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R417 VRD-RA2BE101J J 100 1/8W Carbon AB R418 VRS-CY1JF152J J 1.5k 1/16W M-Ox. AA R419 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R423 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R426 VRS-CY1JF271J J 270 1/16W M-Ox. AA R440 VRS-CY1JF821J J 820 1/16W M-Ox. AA

å R451 VRS-VV3AB103J J 10k 1W M-Ox. AA

R452 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R454 VRD-RA2BE334J J 330k 1/8W Carbon AA R455 VRD-RA2BE392J J 3.9k 1/8W Carbon AA R456 VRS-CY1JF223J J 22k 1/16W M-Ox. AA R457 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R458 VRD-RA2BE334J J 330k 1/8W Carbon AA R459 VRD-RA2BE123J J 12k 1/8W Carbon AA R504 VRD-RA2BE471J J 470 1/8W Carbon AA R505 VRD-RA2BE101J J 100 1/8W Carbon AB R506 VRD-RA2BE683G J 68k 1/8W Carbon AA R507 VRD-RA2BE104G J 100k 1/8W Carbon AA R508 VRD-RA2BE473J J 47k 1/8W Carbon AA R510 VRD-RM2HD1R2J J 1.2 1/2W Carbon AA

å R511 VRN-SV2HB1R5J J 1.5 1/2W M-Film AB

R512 VRD-RM2HD331J J 330 1/2W Carbon AA R516 VRD-RA2BE683G J 68k 1/8W Carbon AA R517 VRD-RA2BE103G J 10k 1/8W Carbon AA R518 VRD-RA2BE154J J 150k 1/8W Carbon AA R524 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R525 VRD-RA2BE473J J 47k 1/8W Carbon AA R552 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R553 VRS-CY1JF273J J 27k 1/16W M-Ox. AA R554 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R602 VRD-RM2HD472J J 4.7k 1/2W Carbon AA

å R603 VRS-SV3LB182J J 1.8k 3.0W M-Ox. AB

R608 VRD-RA2BE471J J 470 1/8W Carbon AA R609 VRD-RA2BE331J J 330 1/8W Carbon AA

å R610 VRS-VV3DB391J J 390 2W M-Ox. AA

R620 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R621 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R631 VRS-CY1JF391J J 390 1/16W M-Ox. AA R632 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R633 VRS-CY1JF472J J 4.7k 1/16W M-Ox. AA R634 VRD-RM2HD101J J 100 1/2W Carbon AA

å R641 VRS-VV3AB682J J 6.8k 1W M-Ox. AA

R642 VRD-RA2BE821J J 820 1/8W Carbon AA

çå R651 VRD-RM2HD1R0J J 1.0 1/2W Carbon AA çå R653 VRD-RA2BE102J J 1.0k 1/8W Carbon AA çå R654 VRD-RA2BE473J J 47k 1/8W Carbon AA çå R655 VRS-CY1JF104J J 100k 1/16W M-Ox. AA

å R659 VRN-VV3ABR33J J 0.33 1W M-Film AA å R661 VRN-VV3ABR47J J 0.47 1W M-Film AA å R701 VRW-KQ4AC2R7K J 2.7 10W Cement AE å R702 VRW-KQ3HC1R5K J 1.5 5W Cement AE

R703 VRD-RM2HD184J J 180k 1/2W Carbon AA R704 VRD-RM2HD184J J 180k 1/2W Carbon AA

å R705 VRS-VV3LB272J J 2.7k 3.0W M-Ox. AB å R706 VRN-VV3AB3R3J J 3.3 1W M-Film AA å R707 VRS-KT3LB562J J 5.6k 3.0W M-Ox. AC å R708 VRS-KT3LB562J J 5.6k 3.0W M-Ox. AC å R709 VRN-RV3DB4R7J J 4.7 2W M-Film AB

R710 VRD-RA2BE124J J 120k 1/8W Carbon AA

å R711 VRN-VV3ABR22J J 0.22 1W M-Film AA

R712 VRD-RM2HD1R0J J 1.0 1/2W Carbon AA

å R713 VRN-SV2HBR68J J 0.68 1/2W M-Film AB

R714 VRD-RA2BE180J J 18 1/8W Carbon AA R715 VRD-RA2BE101J J 100 1/8W Carbon AB R716 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R717 VRD-RA2BE270J J 27 1/8W Carbon AA R718 VRD-RA2BE392J J 3.9k 1/8W Carbon AA R719 VRD-RA2BE153J J 15k 1/8W Carbon AA R720 VRD-RA2BE821J J 820 1/8W Carbon AA

å R725 VRC-UA2HG825K J 8.2M 1/2W Solid AA å R726 VRC-UA2HG825K J 8.2M 1/2W Solid AA

R730 VRS-SV3LB100J J 10 3.0W M-Ox. AC

(20LK60A)

R731 VRD-RA2EE330J J 33 1/4W Carbon AA

(20LK60A)

R732 VRS-KA3NG330J J 33 7.0W M-Ox. AE

(20LK60A) R751 VRN-SV2HBR22J J 0.22 1/2W M-Film AA R752 VRD-RA2BE561J J 560 1/8W Carbon AA

å R753 VRS-KA3HG3R3K J 3.3 5W M-Ox. AD å R755 VRS-VV3DB470J J 47 2W M-Ox. AA

R756 VRD-RA2BE562J J 5.6k 1/8W Carbon AA

å R757 VRN-VV3LBR47J J 0.47 3.0W M-Film AC å R758 VRS-SV2HC180J J 18 1/2W M-Ox. AA

R801 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R802 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R803 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R804 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R805 VRS-CY1JF222J J 2.2k 1/16W M-Ox. AA R806 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R902 VRS-CY1JF750J J 75 1/16W M-Ox. AA R905 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA

(20LK60A) R906 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R924 VRS-CY1JF104J J 100k 1/16W M-Ox. AA

(20LK60A) R925 VRS-CY1JF104J J 100k 1/16W M-Ox. AA R961 VRD-RA2BE101J J 100 1/8W Carbon AB R962 VRD-RA2BE101J J 100 1/8W Carbon AB R2002 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2006 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2008 VRD-RA2BE224J J 220k 1/8W Carbon AA R2009 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R2010 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R2011 VRS-CY1JF821J J 820 1/16W M-Ox. AA R2012 VRS-CY1JF471J J 470 1/16W M-Ox. AA R2020 VRD-RM2HD223J J 22k 1/2W Carbon AA R2022 VRD-RA2BE333J J 33k 1/8W Carbon AA R2024 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2025 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2026 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2027 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2028 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R2029 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R2031 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2032 VRD-RA2BE471J J 470 1/8W Carbon AA R2040 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA R2041 VRD-RA2BE333J J 33k 1/8W Carbon AA R2042 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2043 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2044 VRS-CY1JF682J J 6.8k 1/16W M-Ox. AA R2045 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2047 VRS-CY1JF221J J 220 1/16W M-Ox. AA

Page 28

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-A: DUNTK9731WEV1(20LK30A) PWB-A: DUNTK9731WEV2(20LK60A)

MAIN UNIT (Continued)

R2048 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA R2049 VRS-CY1JF333J J 33k 1/16W M-Ox. AA R2054 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2055 VRD-RA2BE103J J 10k 1/8W Carbon AA R2060 VRS-CY1JF221J J 220 1/16W M-Ox. AA R2061 VRS-CY1JF562J J 5.6k 1/16W M-Ox. AA R2062 VRS-CY1JF183J J 18k 1/16W M-Ox. AA R2063 VRD-RA2BE222J J 2.2k 1/8W Carbon AA R2064 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA R2066 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2067 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2068 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2070 VRS-CY1JF103J J 10k 1/16W M-Ox. AA R2101 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2102 VRS-CY1JF101J J 100 1/16W M-Ox. AA R2501 VRS-CY1JF123J J 12k 1/16W M-Ox. AA R2503 VRS-CY1JF273J J 27k 1/16W M-Ox. AA R2504 VRS-CY1JF123J J 12k 1/16W M-Ox. AA R2505 VRS-CY1JF563J J 56k 1/16W M-Ox. AA R2506 VRS-CY1JF563J J 56k 1/16W M-Ox. AA R2507 VRS-CY1JF823J J 82k 1/16W M-Ox. AA R2508 VRS-CY1JF153J J 15k 1/16W M-Ox. AA R2509 VRS-CY1JF272J J 2.7k 1/16W M-Ox. AA R2601 VRD-RA2BE470J J 47 1/8W Carbon AA R3001 VRD-RA2BE221J J 220 1/8W Carbon AA

(20LK60A)

R3002 VRD-RA2BE221J J 220 1/8W Carbon AA

(20LK60A)

R3003 VRS-CY1JF105J J 1.0M 1/16W M-Ox. AA

(20LK60A)

R3004 VRS-CY1JF104J J 100k 1/16W M-Ox. AA

(20LK60A)

R3005 VRS-CY1JF623J J 62k 1/16W M-Ox. AA

(20LK60A)

R3007 VRS-CY1JF332J J 3.3k 1/16W M-Ox. AA

(20LK60A)

R3008 VRS-CY1JF302J J 3.0k 1/16W M-Ox. AA

(20LK60A)

R3010 VRS-CY1JF392J J 3.9k 1/16W M-Ox. AA

(20LK60A)

R3011 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA

(20LK60A)

R3012 VRS-CY1JF102J J 1.0k 1/16W M-Ox. AA

(20LK60A)

R3013 VRD-RA2BE2R2J J 2.2 1/8W Carbon AA

(20LK60A)

P702 QPLGN0207CEZZ J Plug, 2-pin(M) AA P751 QPLGN0461CEZZ J Plug, 4-pin(YBN) AB P901 QPLGN0561CEZZ J Plug, 5-pin(E) AB P2001 QPLGN0561CEZZ J Plug, TP2001-5 AB

RMC2601

RRMCU0222CEZZ J R/C Receiver AL or

RRMCU0216CEZZ HM711 LX-GZ3001PEZZ R Screw AB HM712 LX-GZ3001PEZZ R Screw AB HM713 LX-GZ3001PEZZ R Screw AB HM714 LX-GZ3001PEZZ R Screw AB HM715 LX-GZ3001PEZZ R Screw AB HM716 LX-GZ3001PEZZ R Screw (20LK60A) AB HM717 LX-GZ3001PEZZ R Screw (20LK60A) AB HM718 LX-GZ3002PEZZ R Screw (20LK60A) AB HM719 LX-GZ3002PEZZ R Screw (20LK60A) AB HM721 LX-GZ3002PEZZ R Screw AB HM722 LX-GZ3002PEZZ R Screw AB HM723 LX-GZ3002PEZZ R Screw AB HM724 LX-GZ3002PEZZ R Screw AB HM729 LX-GZ3001PEZZ R Screw AB HM730 LX-GZ3001PEZZ R Screw AB HM731 LX-GZ3001PEZZ R Screw AB HM732 LX-GZ3001PEZZ R Screw AB HM733 LX-GZ3001PEZZ R Screw AB HM734 LX-GZ3001PEZZ R Screw AB HM735 LX-GZ3001PEZZ R Screw AB HM736 LX-GZ3001PEZZ R Screw AB HM737 LX-GZ3001PEZZ R Screw AB HM738 LX-GZ3001PEZZ R Screw (20LK60A) AB HM739 LX-GZ3001PEZZ R Screw (20LK60A) AB HM740 LX-GZ3001PEZZ R Screw AB RDA351

PRDAR0102GJFW X Heat Sink, for IC351 RDA352

PRDAR0102GJFW X Heat Sink, for IC352 RDA501

PRDAR0103GJFW X Heat Sink, IC501 RDA601

PRDAR0216PEFW R Heat Sink, for Q602 AE RDA701

PRDAR0222PEFW R Heat Sink, for Q701 AH

LHLDW1002PEZZ R Holder AB

LX-BZ3100CEFD J Screw AA

LX-BZ3100CEFD J Screw (20LK60A) AA

LX-TZ3004CEFD J Screw AA

QCNW-2047PEZZ R Connecting Cord AK

(20LK60A)

SWITCHES

S2501 QSW-K0079GEZZ J Power AB S2502 QSW-K0079GEZZ J Vol-Down AB S2503 QSW-K0079GEZZ J Vol-Up AB S2504 QSW-K0079GEZZ J Ch-Down AB S2505 QSW-K0079GEZZ J Ch-Up AB

MISCELLANEOUS PARTS

å RY701 RRLYU0036CEZZ J Relay AM å RY751 RRLYU0036CEZZ J Relay AM å F701 QFS-C3229CEZZ J Fuse, 3.15A AD

FB602 RBLN-0037CEZZ J Ferrite Bead AB FB603 RBLN-0037CEZZ J Ferrite Bead AB FB701 RBLN-0037CEZZ J Ferrite Bead AB FB702 RBLN-0037CEZZ J Ferrite Bead AB FB751 RBLN-0080CEZZ J Ferrite Bead AD FB752 RBLN-0037CEZZ J Ferrite Bead AB FH701 QFSHD1013CEZZ J Fuse Holder AC FH702 QFSHD1014CEZZ J Fuse Holder AC P302 QPLGN0461CEZZ J Plug, 4-pin(S) AB P401 QPLGN0561CEZZ J Plug, 5-pin(GNB) AB P601 QPLGN0603CEZZ J Plug, 6-pin(K) AB P651 QPLGN0361CEZZ J Plug, TP651-3 AB P701 QPLGN0269GEZZ J Plug, 2-pin(P) AB

Page 29

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

PWB-B: DUNTK9432WEV5

CRT UNIT

TRANSISTORS

Q852 VS2SC2229O/1E J 2SC2229 AD Q854 VS2SC2229O/1E J 2SC2229 AD Q856 VS2SC2229O/1E J 2SC2229 AD Q881 VS2SA1266-Y-1 J 2SA1266(Y) AA

or VS2SA1015-Y-1

DIODES

You can substitute "RH-DX0045GEZZ" and "RH-DX0446CEZZ" for "VHD1SS119//-1".

D881 VHD1SS119//-1 J Diode AB D882 VHD1SS119//-1 J Diode AB D885 VHD1SS119//-1 J Diode AB

COIL

L851 VP-DF151K0000 J Peaking 150µH AB

CAPACITORS

[EL.··· Electrolytic]

C851 VCKYPA1HB271K J 270p 50V Ceramic AA C852 VCKYPA1HB271K J 270p 50V Ceramic AA C853 VCKYPA1HB271K J 270p 50V Ceramic AA C854 RC-KZ0016CEZZ J 0.01 1.4kV Ceramic AC C881 VCEA0A1CW106M J 10 16V EL. AB C883 VCEA0A1CW336M J 33 16V EL. AB

RESISTORS

[M-Ox.··· Metal Oxide]

R851 VRD-RA2BE470J J 47 1/8W Carbon AA R852 VRD-RA2BE221J J 220 1/8W Carbon AA R853 VRD-RA2BE121J J 120 1/8W Carbon AA

å R857 VRS-VV3AB123J J 12k 1W M-Ox. AA

R858 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R859 VRD-RA2BE470J J 47 1/8W Carbon AA R860 VRD-RA2BE221J J 220 1/8W Carbon AA R861 VRD-RA2BE121J J 120 1/8W Carbon AA

å R865 VRS-VV3AB123J J 12k 1W M-Ox. AA

R866 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R867 VRD-RA2BE470J J 47 1/8W Carbon AA R868 VRD-RA2BE221J J 220 1/8W Carbon AA R869 VRD-RA2BE121J J 120 1/8W Carbon AA

å R873 VRS-VV3AB123J J 12k 1W M-Ox. AA

R874 VRD-RM2HD332J J 3.3k 1/2W Carbon AA R881 VRD-RA2BE102J J 1.0k 1/8W Carbon AA R882 VRD-RA2BE391J J 390 1/8W Carbon AA R883 VRD-RA2BE561J J 560 1/8W Carbon AA R884 VRD-RA2BE152J J 1.5k 1/8W Carbon AA R885 VRD-RA2BE470J J 47 1/8W Carbon AA

MISCELLANEOUS PARTS

å QACCZ3008PEZZ R AC Cord AN

QCNW-1964PEZZ R Connecting Cord AF QCNW-2011PEZZ R Connecting Cord AH QCNW-2110PEZZ R Connecting Cord AG VSP9050PB108A J Speaker (20LK30A) AP VSP9050PB11WA J Speaker (20LK60A) AP

SUPPLIED ACCESSORIES

TiNS-6487GJZZ X Operation Manual TiNS-6489GJZZ X Operation Manual RRMCG1339CESA J Infrared R/C Unit AT QANTR0018PEZZ R Rod Antenna AQ QPLGA0017CEZZ J Plug AK RUNTK0165CEZZ J Antenna Box Unit AM

(20LK30A) (20LK60A)

PACKING PARTS

(NOT REPLACEMENT ITEM)

SPAKC0002GJZZ – Packing Case(20LK30A) — SPAKC0003GJZZ – Packing Case(20LK60A) — SPAKP0102GJZZ – Polyethylene Foam Wrap — SPAKX0002GJZZ – Buffer Material — SSAKA0101GJZZ – Polyethylene Bag —

CABINET PARTS

1 CCABA0002WEH0 X Front Cabinet Ass'y 1 CCABA0003WEH0 X Front Cabinet Ass'y 1-1

Not Available

1-2 GCOVA0002GJSA X R/C Cover 1-3 HBDGB0019PESA R Badge, "SHARP" AD 1-4 JBTN-0002GJSA X Button 2 GCABB0002GJKA X Rear Cabinet

(20LK30A) (20LK60A)

– Front Cabinet —

MISCELLANEOUS PARTS

P851 QPLGN0561CEZZ J Plug, 5-pin(GBN) AB P852 QPLGN0461CEZZ J Plug, 4-pin(YBN) AB SC851 QSOCV0933CEZZ J CRT Socket AH

PWB-C: DUNTK9732WEV0(20LK30A) PWB-C: DUNTK9732WEV2(20LK60A)

FRONT A V UNIT

MISCELLANEOUS PARTS

J1001 QJAKE0150CEZZ J Jack, Video IN AD J1002 QJAKE0185CEZZ J Jack, Audio IN AE J1003 QJAKE0184CEZZ J Jack, Audio IN (20LK60A) AE P1001 QPLGN0561CEZZ J Plug, 5-pin(E) AB

1-2

1 21-1

1-3

1-4

Page 30

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

★ Polyethylene Foam Wrap

PACKING OF THE SET

★ Polyethylene Bag

Operation manual Infrared R/C Unit Rod Antenna AC Adapter Antenna Adapter

★ Batteries

★ Buffer Material

★ MARK : Not Replacement Items.

FRONT

★ Packing Case

Use tapes to fix the packing case.

REAR

Page 31

20LK30A/60A

Ref. No. Part No. ★ Description Code Ref. No. Part No. ★ Description Code

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

TQ0641-S

Apr. 1999 Printed in Japan

SY. KG

SHARP CORPORATION AV Systems Group Quality & Reliability Control Center Yaita, Tochigi 329-2193, Japan