Page 1
Page 2
EFFECTIVE AND SPACIOUS
For hardware that’s not meant to be hidden, we’ve designed and developed the TG6 RGB. This midi ATX case
provides hardware with ample space and an exceptional platform for showcasing. Each of the four preinstalled 120 mm addressable RGB fans is equipped with three rows of encircling LEDs. These provide stepless
lighting effects within the entire RGB spectrum and optimally illuminate the installed hardware.
Page 3
8-PORT ADDRESSABLE RGB
5V
D G
5V
D G
5VD G
5V
D G
RGB SW
+
-
CONTROLLER
The TG6 RGB comes with a preinstalled addressable RGB controller. With compatible mainboards,
this will function as a hub for controlling and synchronizing up to
eight addressable LED components, which will illuminate in up
to 16.8 million colors. The controller is connected to the power
supply via a SATA connector and
to a mainboard via a 4-pin or 3-pin
header for addressable LEDs with
the pinout: 5V-D-coded-G or
V-D-G.
SATA
Addressable RGB LED Fans/ Strips
5V
D G5VD G
5V
D G5VD G5VD G5VD G
Addressable RGB LED Fans/ Strips
or
V D G
VDG
+5V D G
D G5VD G
Mainboard Addressable
RGB Pin Header
5V
MANUAL COLOR CONTROL
The TG6 RGB also has a manual color control function for mainboards which do not have headers for
addressable LED components. With this, the RGB controller is not connected to the mainboard, but
rather connected to the power supply and the reset switch of the PC case. The switch’s reset function
is then replaced with a new function which allows up to twenty lighting modes to be cycled through
and selected, or, if desired, the lighting can be turned off.
Yellow Cyan Pink
RGB
RGB
Mode 6
Mode 7
RGB
Mode 5
RGB
Mode 4
RGB
Mode 1
RGB
Mode 2
RGB
Mode 3
RGB
Mode 9
Blue White
RGB
Mode 8
RGB
Mode 13
RGB
Mode 12
RGB
Mode 11
Red Green
RGB
Mode 10
SATA
Addressable RGB LED Fans/ Strips
5V
D G5VD G
5V
D G5VD G5VD G5VD G
Addressable RGB LED Fans/ Strips
D G5VD G
5V
+
RGB SW
-
Page 4
RGB CONNECTION
COMPATIBILITY
The TG6 RGB case, along with all other Sharkoon products marked
with the Addressable RGB logo, are certified for Asus Aura Sync, MSI
Mystic Light Sync, Gigabyte Fusion and ASRock Polychrome SYNC.
These products are thus easy to incorporate into existing systems.
Sharkoon products marked with the "ADDRESSABLE RGB" logo
are compatible with mainboards which have headers for addressable RGB LED fans and strips. The headers should have the
pinout 5V-D-coded-G or 5V-D-G. Examples of these RGB connections from the most important mainboard manufacturers are
shown below. The RGB pin configuration is independent of manufacturer. However, the naming and marking of these connections
may vary between manufacturers. For further information concerning compatibility, refer to the manual of your mainboard, or visit
the manufacturer's website.
MSI ASUS ASROCK ASUSGIGABYTE
Page 5
DETACHABLE FAN TRAY DESIGN
If water cooling is the preferred method for heat removal, then the TG6 RGB is just the case you need. For just a radiator,
without fans, the front of the case offers considerable room - with an installation height up to 5.2 cm. This is due, for the
first time, to the three pre-installed front fans being secured to the front of the chassis and operating directly between
the front panel and fan tray. The fan tray can be removed together with the fans, facilitating the installation of a radiator
up to 360 mm in length.
MODULAR
FAN DESIGN
The pre-installed fans in
the TG6 RGB set themselves apart with their new
modular frame design
which has no visible
screws. The rubberized
contact points and aerodynamic fan blades sustain
both a strong and a quiet
airflow.
Page 6
THE PERFECT STAGE FOR
YOUR HARDWARE
The hardware is viewable through the tempered glass front and side panels, while the power supply, HDDs and cabling
disappear within the power supply tunnel or behind the mainboard tray. For a more elegant appearance and enhanced
protection of the glass, the side panel has been designed without any visible screws or bolts. Instead, it is attached via
thumbscrews on the rear panel of the case.
Page 7
ROOMY INTERIOR
45.2 cm
16.7 cm
Max. Length
Graphics Card: 40 cm
46.5 cm
1x 2.5" SSD 1x 2.5" SSD
Since demanding hardware requires
room, the TG6 RGB is spaciously
designed. It supports graphics cards
up to 40 cm in length, CPU coolers
with a height of up to 16.7 cm and
power supplies with a maximum
length of 20.5 cm. Up to three 3.5"
HDDs and up to four 2.5" SSDs can be
installed. If required, two of the SSDs
can be mounted on top of the power
supply tunnel.
1x 2.5" SSD
1x 2.5" SSD
3x 3.5" HDDs
or 2x 2.5" SSDs
Max. Length
Power Supply: 20.5 cm
8-Port Addressable
RGB Controller
Extra-Long Thumbscrew Slots
for Perfect Positioning of
HDD/SSD Cage
Page 8
STRONG AIRFLOW
4x
120 mm
Addressable
RGB LED Fans
Removable Dust Filters
in Both Sides of Front Panel
Easily Accessible Top I/O Ports
above Front Panel
Tempered Glass Cableless Front Panel Design
Removable Dust Filter
on the Bottom Panel
Magnetic, Easy-to-Clean
Dust Filter on Top Panel
Page 9
SPECIFICATIONS
General:
Form Factor: ATX
Expansion Slots: 7
Interior Painting:
Tool-Free Devices Installation:
Cable Management System:
Side Panel: Tempered Glass
Weight: 8.1 Kg
Dimensions (L x W x H): 45.2 x 21.5 x 46.5 cm
RGB Compatibility:
Type: Addressable
Port: 8-Port
Manual Control: 20 Modes
Mainboard Compatibility: MSI Mystic Light Sync,
ASUS Aura Sync, Gigabyte
RGB Fusion Ready,
ASRock Polychrome SYNC
RGB Pinout: 5V-D-G & 5V-D-coded-G
I/O:
USB 3.0 (Top): 2
USB 2.0 (Top): 2
Audio (Top):
Fan Configuration:
Front Panel: 3x 120 mm Addressable
RGB Fans (Pre-Installed)
or Radiator (Optional)*
Rear Panel: 1x 120 mm Addressable
RGB Fan (Pre-Installed)
Top Panel: 3x 120 mm or
2x 140 mm Fans (Optional)
Compatibility:
Mainboard: Mini-ITX, Micro-ATX, ATX
Max. Length Graphics Cards: 40 cm
Max. Height CPU Cooler: 16.7 cm
Max. Length Power Supply: 20.5 cm
Max. Height Radiator
(Front): 5.2 cm
Package Contents:
TG6 RGB
Accessory Set
Manual
*Optional radiators can be installed instead of fans
Maximum Drive Bays:
3.5": 3
2.5": 4
Loading...