Shark Zero M Navigator Pet Pro ZU60 Series Owner's Manual
/MD
®
Navigator
TM/MC
Pet Pro
Upright Vacuum
Aspirateur vertical
Aspiradora vertical
ZU60 Series • Série • Serie
OWNER’S GUIDE
GUIDE D’UTILISATION
GUÍA DEL PROPIETARIO
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY • PLEASE READ CAREFULLY BEFORE USE
If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit,
contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
WARNING
To reduce the risk of fire, electric shock, injury, or property damage:
GENERAL WARNINGS
1. Your vacuum cleaner may consist of
a motorized nozzle, wand, hose, and/
or vacuum pod. This device contains
electrical connections, electrical
wiring, and moving parts that
QUICK
potentially present risk to the user.
2. Use only identical replacement parts.
START
3.
Carefully observe and follow the
instructions provided below to avoid
GUIDE
improper use of the appliance. DO NOT
use the vacuum for any purpose other
than those described in this manual.
4. Before use, carefully inspect all parts
for any damage. DO NOT use if any
parts are damaged.
5. The use of an extension cord is
NOT recommended.
6. This vacuum cleaner contains
no serviceable parts.
USE WARNINGS
7. DO NOT allow the appliance to be
used by children. Close supervision is
necessary when used near children.
This is not a toy.
8. Always turn off the vacuum cleaner
before connecting or disconnecting
any motorized nozzles or other
accessories.
9. DO NOT handle plug or vacuum
cleaner with wet hands.
10. DO NOT use without filters in place.
11. Only use Shark® branded filters
and accessories. Failure to do so
will also void the warranty.
12. DO NOT damage the power cord:
a) DO NOT pull or carry vacuum
cleaner by the cord or use the
cord as a handle.
b) DO NOT unplug by pulling
on cord. Grasp the plug, not
the cord.
c) DO NOT run the vacuum cleaner
over the power cord, close a door
on the cord, pull the cord around
sharp corners, or leave the cord
near heated surfaces.
13. DO NOT put any objects into nozzle
or accessory openings. DO NOT use
with any opening blocked; keep free
of dust, lint, hair, and anything that
may reduce airflow.
14. DO NOT use if nozzle or accessory
airflow is restricted. If the air paths or
the motorized floor nozzle become
blocked, turn the vacuum cleaner
off and unplug from electrical outlet.
Remove all obstructions before you
plug in and turn on the unit again.
15. Keep nozzle and all vacuum
openings away from hair, face,
fingers, uncovered feet, or
loose clothing.
16. DO NOT use if vacuum cleaner is
not working as it should, or has been
dropped, damaged, left outdoors, or
dropped into water.
17. Use extra care when cleaning
on stairs.
18. DO NOT leave the vacuum cleaner
unattended while plugged in.
19. When powered on, keep the vacuum
cleaner moving over the carpet surface
at all times to avoid damaging the
carpet fibers.
20. DO NOT place vacuum cleaner
on unstable surfaces such as chairs
or tables.
21. Your Shark® vacuum may not be
designed to stand up on its own. When
taking a break from cleaning, you may
need to lean it against furniture or a
wall, or lay it flat on the floor. Using
the vacuum for an application where
the unit lacks stability may result in
personal injury.
22. DO NOT use to pick up:
a) Liquids
b) Large objects
c) Hard or sharp objects
(glass, nails, screws, or coins)
d) Large quantities of dust (drywall
dust, fireplace ash, or embers).
DO NOT use as an attachment to
power tools for dust collection.
e) Smoking or burning objects
(hot coals, cigarette butts,
or matches)
f) Flammable or combustible
materials (lighter fluid, gasoline,
or kerosene)
g) Toxic materials (chlorine bleach,
ammonia, or drain cleaner)
To reduce the risk of electric shock, this appliance has a polarized plug (one blade
is wider than the other). This plug will fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a
qualified electrician to install the proper outlet. Do not change the plug in any way.
23. DO NOT use in the following areas:
a) Poorly lit areas
b) Wet or damp surfaces
c) Outdoor areas
d) Spaces that are enclosed and may
24. Turn off all controls before plugging in
25. Unplug from electrical outlet
26. Hand wash with water only.
27. During cleaning or routine
28. Allow all filters to air-dry completely
29. Make sure the dust cup and all filters
30. If provided, secure the power
contain explosive or toxic fumes
or vapors (lighter fluid, gasoline,
kerosene, paint, paint thinners,
mothproofing substances, or
flammable dust)
or unplugging the vacuum.
when not in use and before
any maintenance or cleaning.
Washing with cleaning chemicals
could damage the unit.
maintenance, DO NOT cut anything
other than hair, fibers, or string
wrapped around the brushroll.
before replacing in the vacuum to
prevent liquid from being drawn
into electric parts.
are in place after routine maintenance.
cord around the two cord hooks
during storage.
SAVE THESE INSTRUCTIONS
sharkclean.comsharkclean.com
ASSEMBLY ASSEMBLY
Cord Clip
2
(Click)
1
(Click)
1. Insert wand into pod.
2. Insert handle into wand.
3. Attach hose to back of vacuum pod.
4. Attach hose to clip on wand.
5. Insert C-shaped clip onto base of vacuum pod and remove tape.
6. Store accessories on tool storage posts.
For proper operation, ensure all parts are firmly clicked into place.
(Click)
3
(Click)
5
(Click)
Upper Cord Hook
4
Tool Storage Posts
6
POWER CORD
UPPER CORD HOOK CORD CLIP
For cord access, rotate upper hook down and
remove cord.
Use cord clip located on the side of wand to
hold cord in place while vacuuming.
sharkclean.comsharkclean.com
WHOLE-HOME CLEANING
WHOLE-HOME CLEANING
Select surface setting:
O Power O
I Hard Floor
For bare floors and small area rugs.
II Carpet
For carpets.
SETTINGS
Your Suction Control slider located on the top of the
handle allows you to adjust your suction depending
on your floor type.
MIN: to reduce suction and increase maneuverability
on carpets.
MAX: to increase suction on bare floors.
BRUSHROLL INDICATOR LIGHT
CLEANING MODES
UPRIGHTPOWER/SURFACE SWITCH SUCTION CONTROL
To engage brushroll, place foot on floor nozzle
and tilt handle back.
Handle
INDICATOR LIGHT
WHAT DOES THE BRUSHROLL INDICATOR LIGHT MEAN?
Solid Green: The brushroll is spinning and working as it should.
Solid Red: There is a jam in the brushroll area. Turn your vacuum o, unplug from the wall and
remove any blockages in the nozzle.
Flashing Red: The motorized floor nozzle is overheating. Turn your vacuum o and wait a
minimum of 45 minutes for it to cool down.
Press the Handle Release button to detach the
handle from the wand.
NOTE: All accessories are compatible with both the wand and the handle.NOTE: For deep carpet cleaning per ASTM F608 (embedded dirt in carpets), set to MAX suction and use setting II, Carpet.
ABOVE-FLOOR—WANDABOVE-FLOOR—HANDLE
Press the Wand Release button to detach the
wand from the pod.
sharkclean.comsharkclean.com
EMPTYING THE DUST CUP
CLEANING AND REPLACING THE FILTERS
IMPORTANT: Unplug the power cord before performing any maintenance.
To remove Dust Cup, press button on top of dust
cup handle. Tilt dust cup forward, then lift to
remove.
Press lower release button to open bottom of
dust cup.
CLEANING FILTERS
Regularly clean and replace your filters to keep your vacuum's suction power optimal.
To clean filters, rinse with cold water only to prevent damage from cleaning chemicals. Allow all
filters to air-dry for at least 24 hours before reinstalling them to prevent liquid from being drawn
into electricparts.
IMPORTANT: DO NOT use soap when cleaning the filters.
Foam
Felt
CLEAN PRE-MOTOR FILTERS
EVERY 3 MONTHS
Remove Dust Cup, then lift out Filters.
Cover
latch
Press down top of Filter Door. Tilt Filter Door
and lift out. Press tab at top of HEPA Filter
and pull away from the base of the vacuum.
To reinstall, insert HEPA filter into unit and
replace the filter door.
Post-Motor
Filter
CLEAN HEPA FILTER
EVERY YEAR
To remove collected debris from Lint Screen,
press top release button and lift handle to
open. Gently brush lint screen to clean.
To reinstall, place bottom of dust cup into
pod and then tilt back until it clicks into place.
REPLACING FILTERS
Follow the previous instructions for removing filters. The Pre-Motor Filter should be replaced every
2.5 years. The HEPA Filter should be replaced every 3 years.
Replacement
Pre-Motor Foam &
Felt Filter Kit
NOTE: To order replacement parts and filters, visit sharkaccessories.com.
Replacement
HEPA Filter
sharkclean.comsharkclean.com
MAINTENANCE
Zero-M Technology
Shark’s Zero-M™ self-cleaning brushroll delivers non-stop hair removal. If you run over a hard or
sharp object or notice a noise change while vacuuming, check for blockages or objects caught in
the brushroll.
NOTE: Do not be alarmed if there is visible hair wrap on the brushroll at any given time, as it should
eventually make its way to the dust cup.
CLEANING THE BRUSHROLL
CHECKING FOR BLOCKAGES
Using a coin, turn locks counterclockwise, then lift the door to access Brushroll.
DEBRIS WRAPPED AROUND BRUSHROLL DEBRIS BEHIND BRUSHROLL
Detach hose from vacuum pod, and check hose and
opening on back of pod for blockages.
Detach wand from power unit, lay unit down, and
check opening for blockages.
Detach wand from floor nozzle and handle, and
check both ends for blockages.
Detach handle from wand and hose from the
vacuum pod, and check openings for blockages.
Clean o any debris on the bristles.
NOTE: If any hair is wrapped around the brushroll, extending
cleaning time will allow Zero-M technology to remove it for
you. If some fibers remain wrapped around brushroll after
continued use, carefully cut debris with scissors and remove
from brushroll.
If you run over a hard or sharp object or
notice a noise change while vacuuming, check
for blockages or objects caught behind the
brushroll.
Clear away any dust, dirt, or blockages in Debris
Intake.
To close the cover, push down until it clicks into
place, then close the locks with a coin.
Detach dust cup from vacuum pod. Empty dust
cup, remove debris from lint screen, and check for
blockages.
sharkclean.comsharkclean.com
AVAILABLE ACCESSORIES TROUBLESHOOTING
Duster Crevice Tool
A
Two cleaning tools in one. The crevice tool
gives you extended cleaning reach for small
spaces, while the soft dusting brush cleans a
multitude of surfaces.
Wide Upholstery Tool
B
Wide cleaning path helps remove pet hair,
dust, and large debris from mattresses,
couches, curtains, lampshades, and other
delicate upholstered surfaces.
C
Hair Removal Multi-Tool
A single convertible tool for cleaning tough
pet messes two ways: first, a rubber bristle
brush for cleaning stubborn hair from
carpeted areas. Then remove the bristles to
reveal an upholstery tool perfect for cleaning
couches and bedding.
Pet Power Brush
D
Designed to remove pet hair and ground-in
dirt from carpeted stairs and upholstery.
A
• Check filters to see if they need cleaning. Follow instructions for rinsing and air-drying the
filters before reinserting in the vacuum.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzle, wand, pod, and accessories for blockages. Clear any
blockages found.
(Refer to Checking for Blockages section for more information.)
• If any string, carpet fibers, or hair is wrapped around the brushroll, extend cleaning time to
allow Zero-M™ technology to remove it.
– If some hair or fibers remain wrapped around brushroll after continued use, remove the floor
Vacuum is not picking up debris. No suction or light suction.
B
nozzle cover and carefully cut debris with scissors and remove from brushroll. See Cleaning
the Brushroll section for more information.
Vacuum lifts area rugs.
• Make sure Power/Surface switch is set to Hard Floor (setting I).
• Suction is powerful. Take care when vacuuming area rugs or rugs with delicately sewn edges.
Brushroll does not spin in carpet cleaning mode.
• If the Brushroll Indicator Light turns red, immediately turn o and unplug the vacuum. Remove
pod from floor nozzle and clear any blockages. Reconnect nozzle, plug in vacuum, and turn on
C
power.
• With the power on, recline the handle, which will automatically turn on the brushroll.
• Ensure that the Power/Surface switch is set to Carpet (setting II) for brushroll
to spin.
Vacuum turns o on its own or indicator light flashes red.
This vacuum is equipped with a motor-protective thermostat. If your vacuum overheats, the
thermostat will automatically turn the suction motor o. Perform the following steps to restart
thethermostat:
1. Turn vacuum o and unplug it.
2. Empty dust cup and clean filters (see Emptying the Dust Cup and Cleaning the Filters).
3. Check for blockages in hose, accessories, and inlet openings.
D
4. Allow unit to cool for a minimum of 45 minutes.
5. Plug in vacuum and turn it on.
6. Restart the unit with the Power/Surface switch.
E
Under-Appliance Wand
E
Clean under and behind hard-to-move
appliances and furniture with this adjustable
36” tool. Flip the extension piece over to
clean the underside of appliances.
NOTE: Not all accessories come with all units. Please see the enclosed Quick Start Guide for your unit's
configuration. To order additional accessories, visit sharkaccessories.com.
For all other issues, please call Customer Service 1-800-798-7398.
sharkclean.comsharkclean.com
Loading...