Shark SK140, SK141, SK140, SK141 Quick Start Guide
Thank you for choosing a
Shark® Easy Spray™ Steam Mop DLX!
• 99.9% Sanitization* with just water.
• Steam Energized™ Cleanser to break down tough,
stuck on stains.
• Disposable Sanifiber™ Pads are great for quick clean
ups and germy messes.
• Washable MicroFiber Pads lift and lock dirt so your
floors stay clean.
• Ready to use in 30 Seconds.
• Swivel steering for enhanced maneuverability.
STEAM MOP ASSEMBLY
1
1 Insert the extension
tubes into each other.
3 Open the water tank cap, use the
filling flask to fill the tank with water,
then replace & tighten the cap.
2 Place the Washable MicroFiber or
SaniFiber™ Disposable Pad on the
mop head and press down.
2
2
3
USING YOUR STEAM MOP
NOTE: Prime the unit by pumping the handle to release moisture into the pad before use.
4 The height of the mop is
adjustable. Lift the latch on the
tube 90 degrees, extend the
tube to the desired height, then
close and lock.
4
5 Plug in the mop and wait 30
second for the unit to heat up.
The push/pull motion releases
the steam as you mop. Steam
output is adjusted by the speed
of your moping motion.
5
STEPS TO A SHARK® CLEAN FLOOR
1 SWEEP OR VACUUM YOUR FLOOR
We recommend the use of the Shark® Vacuum and/or Sweeper to work
in conjunction with the steam mop for a complete cleaning system.
2 SANITIZE WITH A SHARK® STEAM MOP**
Shark® Steam Mops provide 99.9% sanitization* and are great for
cleaning up stuck on dirt, grime, and footprints.
For extra tough messes, try our new Shark® Steam Energized™ cleanser.
This gentle cleaning solution combines with steam for superior deep
cleaning.
3 REGULAR MAINTENANCE IS KEY
Daily spot cleaning is recommended to keep dirt and grime from
building up in your home.
The range of convenient, quick clean products from Shark® is
guaranteed to help you keep a clean and sanitized home.
** TIP: The initial use of the steam mop may cause streaking or clouding due to
the residue from chemicals and polish previously used on your floors. Regular
use of the steam mop will diminish this effect. For stubborn cases, you may
need to rinse the floor with a mixture of one part vinegar and two parts
water. Remember, a clean mop pad is essential for residue removal.
SK140_QSG
Paper: Quality A (Bright White) 157g/m2
Coating: Matte both sides
* Under controlled test conditions, results may vary.
Issue Resolution
The Easy Spray™ Steam Mop Deluxe will not turn-on. Ensure the power cord is plugged in correctly to a working 120 volt outlet.
P
Easy Spray™ Steam Mop Deluxe will not make steam. Check the water tank. If empty, add water to the steam mop by following the instructions above.
P
Easy Spray™ Steam Mop Deluxe leaves water on the
floor or is hard to push.
P
Easy Spray™ Steam Mop Deluxe left white spot on
the floor.
P
Problem Resolution Checklist
Be sure that the cleaning pad is soaked through and properly affixed to the entire mop head. If the
pad is over saturated, unplug the unit, wait 2 to 3 minutes for the pad to cool, and then replace with
a clean dry mop pad.
Check to see if the cleaning pad is soaked through. We recommend that you unplug the unit and
replace the cleaning pad. Make sure that the cleaning pad is attached correctly.
For brighter, streak free floors, try
ENERGIZEDENERGIZED
cleanser
• Breaks down tough
greasy & stuck on messes
• Non-toxic, biodegradable
Easy Spray™
Steam Mop DLX
P
P
Floors are cloudy, streaky or spotty after steaming.
Unable to Resolve Your Issue?
Looking for Replacement Parts or Accessories? Check out www.sharkclean.com or give our Customer Care Center a call at 1-800-798-7398.
The initial use of the Steam Mop may cause clouding, streaking, or spotting of floors due to the
residue from chemicals previously used to treat the floor. Be sure to follow the “Steps to a Shark®
Clean Floor”.
If you are still having difficulty using the Easy Spray™ Steam Mop, call our Customer Care Center at
1-800-798-7398.
• Safe around kids & pets†
• Great fresh scent
Cleanser available at select retailers and at
www.sharkclean.com
or by calling
†
When used as directed.
1-800-798-7398
GETTING
STARTED
Loading...