Shark Rotator, NV750REF Owner's Manual

Page 1
OWNER’S GUIDE
NV750REF
®
www.PoweredLiftAway.com
800.798.7398
Page 2
2
REGISTER YOUR PURCHASE:
www.PoweredLiftAway.com
800-798-7398
RECORD THIS INFORMATION:
Model Number: ________________________________
Date of Purchase (Keep receipt):
___________________________________________
TECHNICAL SPECIFICATIONS:
Voltage: 120V., 60Hz Watts: 1150W Amps: 9.5A
RECOMMENDED FILTER CLEANING SCHEDULE:
See the MAINTENANCE section for filter cleaning instructions
Foam filter: XFF650 Every 3 months Felt Filter: XFF650 Every 3 months HEPA Filter: XHF650 Every 12 months
Thank you for purchasing the Shark® Rotator® Powered Lift-Away®.
This Owner’s Guide is designed to help you get a complete understanding of your new vacuum cleaner. Please read it carefully and keep it future reference.
If you should have a question about your Shark Rotator, please call the Shark Customer service line at 800-798-7398.
Page 3
800.798.7398
3
FOR HOUSEHOLD USE ONLY
When using an electrical appliance, basic safety precautions should always be observed, including the
following:
WARNING
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK OR
INJURY: 1 DO NOT use outdoors or on wet surfaces. 2 Unplug from electrical outlet when not in use and before
servicing.
3 DO NOT use vacuum cleaner with a damaged cord or plug.
If vacuum cleaner is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to SharkNinja Operating LLC for examination, repair, or adjustment.
4 DO NOT pull or carry vacuum cleaner by the cord or use the
cord as a handle.
5 DO NOT unplug by pulling on cord; to unplug, grasp the
plug, not the cord. 6 DO NOT handle plug or vacuum cleaner with wet hands. 7 DO NOT run the vacuum cleaner over the power cord, close
a door on the cord or pull cord around sharp corners.
8 The use of an extension cord is not recommended. 9 DO NOT leave vacuum cleaner when plugged in. 10 Keep cord away from heated surfaces. 11 Turn off all controls before plugging or unplugging the
vacuum cleaner. 12 Always turn off the vacuum cleaner before connecting or
disconnecting motorized nozzle. 13 Store your vacuum cleaner with the power cord secured
around the two cord holders - as shown in the storage
instructions.
GENERAL USE
14 Use only as described in this manual.
15 DO NOT put any objects into openings. DO NOT use with
any opening blocked; keep free of dust, lint, hair, and
anything that may reduce air flow. 16 Keep your work area well lit. 17 Keep the vacuum cleaner moving over the carpet surface at
all times to avoid damaging the carpet fibers. 18 DO NOT place vacuum cleaner on unstable surfaces such
as chairs or tables.
19 DO NOT allow young children to operate the vacuum
cleaner or use as a toy. Close attention is necessary when used near children.
20 DO NOT use without dust cup and/or filters in place.
HOSE ATTACHMENTS
21 DO NOT use if air flow is restricted; if the air paths, the
hose, or the accessories become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.
22 Keep the end of the hose and accessory openings away
from face and body.
23 Keep cleaning tools and hose suction openings away from
hair, face, fingers, uncovered feet, or loose clothing.
24 Only use manufacturer’s recommended attachments.
DUST CUP/FILTERS/ACCESSORIES
Before turning on the vacuum: 25 Make sure that all filters are thoroughly dry after routine
cleaning.
26 Make sure that dust cup and all filters are in place after
routine maintenance.
27 Make sure accessories are free of blockages. 28 Only use filters and accessories provided by SharkNinja
Operating LLC. [Failure to do so will void the warranty.]
GENERAL CLEANING
29 DO NOT pick up large-sized objects. 30 DO NOT pick up hard or sharp objects such as glass, nails,
screws or coins that could damage the vacuum cleaner.
31 DO NOT pick up smoking or burning objects such as hot
coals, cigarette butts, fireplace ash or matches.
32 DO NOT use to pick up drywall dust. 33 DO NOT pick up flammable or combustible materials such
as lighter fluid, gasoline, or kerosene or use vacuum in areas where they may be present.
34 DO NOT pick up toxic solutions such as chlorine bleach,
ammonia, or drain cleaner.
35 DO NOT use in an enclosed space where vapors are pres-
ent from paint, paint thinner, moth-proofing substances, flammable dust or other explosive or toxic materials.
36 DO NOT vacuum up any liquids. 37 DO NOT immerse vacuum cleaner in water or other liquids. 38 DO NOT use outdoors or on wet surfaces; use only on dry
surfaces.
39 Use extra care when cleaning on stairs.
SAVE THESE INSTRUCTIONS
POLARIZED PLUG
To reduce the risk of electric shock, this vacuum cleaner has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. If the plug does not fit fully into the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT force into outlet or try to modify to fit.
READ ALL INSTRUCTIONS BEFORE USE
IMPORTANT SAFEGUARDS
SAVE THESE INSTRUCTIONS
Page 4
4
1 Place the nozzle on the floor and insert the wand.
2 Insert the handle into the wand.
3 Slide the POD onto the wand.
4 Attach the hose to the back of the pod.
5 Insert the duster crevice tool and upholstery tool into the accessory clips as shown.
ASSEMBLY
2
1
4
3
5
Page 5
Hard Floor
Carpet
Deep Carpet
5
800.798.7398
1 Press POWER and push the surface selector to THICK CARPET/AREA RUG for the best setting for High Pile and Thick
Carpets, Area Rugs, and Specialty Carpets if the vacuum is difficult to push or pull due to high suction. This setting produces reduced suction with motorized brush roll.
2 Press POWER and push the surface selector to CARPET/LOW PILE for the best setting for low pile and normal carpet
types. High suction with motorized brush roll. This is the default carpet setting.
3 Press POWER and push the surface selector to HARD FLOOR for the best setting for hard floors and accessories. High
suction and brush roll off.
4 Place your left foot gently on the floor nozzle and tilt the handle back to start cleaning. Note: The brushroll will only spin
once the vacuum is reclined back.
NOTE: For deep cleaning per ASTM F 608 (embedded dirt in carpets) please set to CARPET/LOW PILE.
THEN
4
2
3
1
Best setting for High Pile Carpet, Area Rugs, and Specialty Carpets if the vacuum is difficult to push or pull due to high suction. Low suction with motorized brushroll.
Best setting for Low Pile Carpet, and Normal Carpet Types. High suction with motorized brushroll. This is the default carpet setting.
Best setting for Hard Floors and Accessories. High suction and brushroll off.
UPRIGHT CLEANING
Page 6
6
Handle
Release Wand
OR
OR
6
5
ABOVE FLOOR CLEANING
5 To clean with the hose, press the WAND or HANDLE release button (depending on the amount of reach required) then lift
handle up.
6 Insert wand or handle directly into desired tool.
Page 7
7
800.798.7398
3
1
2
2
4
1 Press LIFT-AWAY to lift the pod off the wand.
2 To clean with hose, press the WAND or HANDLE release button then lift handle up.
3 Attach desired cleaning tool.
4 For best suction, push the surface selector to HARD FLOOR setting.
NOTE: Select cleaning accessories are included with this model. Additional accessories are available for purchase at
www.PoweredLiftAway.com or by calling 800 798-7398.
LIFT-AWAY™ CLEANING
Use for portable cleaning on stairs or anywhere
Page 8
8
Hard Floor Genie
XHFG650
Durable enough for big crumbs and thumb­tacks, but gentle enough for the most delicate dusting on hardwood and tile floors.
Dusting Brush
134FLI480
Cleans hard surfaces and upholstery.
Caddy
XCAD650
Transform your Rotator into a fully powered canister, giving you the freedom to roll the pod along while keep­ing cleaning tools close by.
Power Brush
150FLI340
Designed for removal of pet hair and ground in dirt from carpeted stairs and upholstery.
Upholstery Tool
159FLI650
ACCESSORIES
NOTE: Select cleaning accessories are included. Others are available for purchase at www.PoweredLiftAway.com or by calling 800 798-7398.
Duster Crevice Tool
158FLI650
Two cleaning tools in one. The crevice tool gives you extended cleaning reach for small spaces, while the dusting brush cleans a multitude of surfaces.
Page 9
Hard Floor
Carpet
Deep Carpet
9
800.798.7398
POWER BUTTON
1 The POWER button turns the vacuum on.
SURFACE SELECTOR
2 Selecting the Hard Floor setting will stop the brushroll from spinning and allow you to clean bare floor and above floor
surfaces with ease. Thick Carpet/Area Rug and Carpet/Low Pile settings refer to the strength of the suction power. “Carpet/ Low Pile” is the default carpet setting and gives you the greatest suction and deep cleaning power. “Thick Carpet/Area Rug” deep cleans higher pile, thicker carpets, specialty carpets, and area rugs with less suction. If the vacuum is difficult to push or pull on certain carpets or area rugs, you can either disengage the brush roll and use the suction only setting or switch the surface selector to Thick Carpet/Area Rug mode.
NOTE: For deep cleaning per ASTM F 608 (embedded dirt in carpets) please set to CARPET/LOW PILE.
CORD HOOKS
3 For quick cord access, rotate upper hook 180° and remove cord. Rotate it back for cord storage.
HEADLIGHTS
4 Illuminozzle designed to illuminate debris in dark areas, the headlights illuminate any time the power is on. The headlights are
long-lasting and designed to last the life of the vacuum.
The LED light on the Illuminator handle will enable you to see dark areas when using the handheld accessories.
FILTERS
5 Remember to clean your filters regularly under normal use. Also, for optimal performance, tap clean filters between washes
as needed.
1
3
2
HELPFUL TIPS
4
5
Page 10
10
EMPTY THE DUST CUP
1 Pull up on the dust cup release latch and lift the dustcup off the pod.
2 Holding the dust cup over a garbage bag or can, press the bottom empty release latch.
3 Press the top dust cup release latch to access the dust screen and remove built-up debris as required.
1
2
3
MAINTENANCE
Page 11
11
800.798.7398
CLEAN THE FILTERS See cleaning schedule on page 2
4 With the dust cup removed, remove and rinse the foam and felt filters every 3 months. Let air dry completely before replacing.
Hand wash only. Tap loose dirt off filters between washes as needed.
5 Once a year open the filter grill and remove and rinse the HEPA filter. Let air dry completely before replacing. Hand wash only.
5
HEPA
4
FOAM FILTER
FILTER FRAME
FELT FILTER
MAINTENANCE
Page 12
12
CHECK FOR BLOCKAGES
REMOVE AND INSPECT:
1 HOSE AND TUBES
Remove floor nozzle and extension wand and shine a flashlight up from the bottom to check for possible blockage. Remove
dustcup and hose to check intake opening and hose elbow.
2 BOTTOM OF FLOOR NOZZLE
a Using a coin, turn the locking screws to the unlock position and pull up to expose the airway. Remove any obstructions,
close and relock.
b Remove any string, carpet fibers or hair that may be wrapped around the brushroll.
MAINTENANCE
a
a
Page 13
13
800.798.7398
Vacuum is not picking up dirt. No suction or light suction
Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the
vacuum.
• Dust cup may be full; empty dust cup.
• Check hose, hose connections, nozzles and accessories for blockages; clear blockages if required.
Vacuum lifts area rugs
• Turn off the unit to disengage the brush roll and restart with the POWER button for suction only cleaning.
Brush roll does not spin
• Pull the handle toward you and release the floor nozzle to disengage the auto-off feature.
• Make sure that the carpet height selector is not on the HARD FLOOR setting.
• Immediately turn off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum
back on.
Vacuum turns off on its own
If the hose connection is not properly latched, it can cause a poor electrical connection and the hose can come loose and power
vacuum OFF.
1. Turn the unit off; unplug the vacuum.
2. Empty the dust cup and clean filters.
3. Check for blockages in hose, accessories and inlet openings.
4. Remove cord from cord hook so hose latch can be seen and engaged. Reassemble.
5. Ensure hose latch makes an audible “click” where the hose meets the back of the vacuum. Also, make sure the hose latch
makes a “click” where the wand plugs into the neck of the floor nozzle, and where the handle plugs into the wand. The
connection of the back of the dust cup to the hose often requires additional force. Ensure you hear the audible click.
6. Pull on hose to ensure latch is fully engaged.
7. If latch is not flush to hose connector, hose is not fully engaged.
8. Plug in the vacuum.
9. Restart the vacuum.
This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat
will automatically turn the unit off. Should this occur, perform the following steps to restart the motor thermostat:
1. Turn the unit off.
2. Unplug the vacuum.
3. Empty the dust cup and clean filters.
4. Check for blockages in hose, accessories and inlet openings.
5. Allow the unit to cool for a minimum of 45 minutes.
6. Plug in the vacuum.
7. Restart the unit.
Note: If vacuum still does not start, contact Customer Service at: 800 798-7398.
TROUBLE-SHOOTING GUIDE
Page 14
14
NOTES
Page 15
800.798.7398
15
SharkNinja Operating LLC warrants this product to be free from material defects and workmanship for a period of one hundred eighty (180) days from the date of purchase when utilized for normal household use, subject to the following conditions, exclusions and exceptions.
The liability of SharkNinja Operating LLC is limited solely, at our option, to either: 1) the cost of the repair or replacement of the unit with a refurbished unit; or 2) an upgrade to a similar model refurbished unit of equal or greater value. Replacement units/parts will be warranted for the remaining portion of the original (180) one hundred eighty day warranty period.
This Limited Warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This Limited Warranty does not cover damage caused by accident, misuse, abuse, negligent handling, incorrect voltage, vandalism, unsuitable environments, damage due to faulty packaging or mishandling in transit, natural disasters or other damages beyond SharkNinja Operating LLC’s control. This Limited Warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alteration to the product or any of its parts, which have been performed by a repair person not authorized by SharkNinja Operating LLC. Since this unit has been represented and sold as a refurbished item, this Limited Warranty does not apply to cosmetic damages or defects, including, but not limited to, scratches, scuffs, dents, or dings. Operating the unit in violation of the instructions in the owner’s manual will void the warranty terms.
If your appliance fails to operate properly while in use under normal household conditions within the Limited Warranty period, you may return the complete appliance and accessories with proof of purchase and date, freight prepaid. For Customer Service support and product specialists, call 1-800-798-7398 or visit our website sharkclean.com.
If the appliance is found by SharkNinja Operating LLC to be defective, in SharkNinja Operating LLC’s sole discretion, we will repair or replace it as set out in the second paragraph above, free of charge. Proof of purchase date and a check made payable to SharkNinja Operating LLC in the amount of $19.95 to cover the cost of return shipping and handling must be included.*
Non-durable parts including, but not limited to, filters, brushes and electrical parts which normally require replacement are specifically excluded from this Limited Warranty.
This Limited Warranty is extended to the original purchaser of this refurbished unit and excludes all other legal, implied and/or conventional warranties. The responsibility of SharkNinja Operating LLC, if any, is limited to the specific obligations expressly assumed by it under the terms of this Limited Warranty. In no event is SharkNinja Operating LLC liable for incidental or consequential damages to anyone of any nature whatsoever. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.
This Limited Warranty gives you specific legal rights, and you may also have other rights which vary from state to state or from province to province.
*IMPORTANT: Carefully pack item to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your Limited Warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.
ONE HUNDRED EIGHTY (180) DAY REFURBISHED PRODUCT LIMITED WARRANTY
Page 16
www.PoweredLiftAway.com
800.798.7398
NV750REF_31_IB_160518_5
© 2016 SharkNinja Operating LLC
Illustrations may dif fer from actual product. We are constantly striving to improve our products,
therefore the specifications contained herein
are subject to change without notice.
For SharkNinja U.S. Patent information visit
sharkninja.com/USPatents.
Lift-Away, Rotator and Shark are registered
trademarks of SharkNinja Operating LLC.
Shar kNinja Operating L LC
Newton, MA USA 02459
Ville St. Laurent, Québec Canada H4S 1A7
www.sharkrocket.com
1.800.798.7398
JOIN THE
CONVERSATION
WATCH AND LEARN
MORE
WE WANT TO HEAR
FROM YOU!
@sharkcleaning
youtube.com/shark
Loading...