Page 1
Floor and Handheld
Steam Cleaner
S6005UK
INSTRUCTIONS
sharkclean.eu
0800 862 0453
Page 2
THANK YOU
for purchasing the Shark Floor and Handheld Steam Cleaner
REGISTER YOUR PURCHASE
registeryourshark.eu
0800 862 0453
Scan QR code using mobile device
TIP: The QR Code
can be found on the
back panel of the
Steam Cleaner.
IPX4
RECORD THIS INFORMATION
Model Number: _________________________
Date Code: _____________________________
Date of Purchase (Keep receipt): ___________
Store of Purchase: _______________________
TECHNICAL SPECIFICATIONS
Voltage: 220-240V~, 50-60Hz
Watts: 1200W
Water Capacity: 500ml
PLEASE READ CAREFULLY AND KEEP FOR
FUTURE REFERENCE.
This instruction manual is designed to help
you get a complete understanding of your
new Steam Cleaner. If you have any questions,
please call the Customer Service line at
0800 862 0453.
CONTENTS
Important Safety Instructions . . . . . . . . . . . . . . . . . . . . . 3
Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Assembling Your Steam Cleaner . . . . . . . . . . . . . . . . . . 7
Using Your Steam Cleaner . . . . . . . . . . . . . . . . . . . . . . . . 9
Intelligent Steam Control® . . . . . . . . . . . . . . . . . . . . . . . .11
Above-Floor Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Using the Garment Steamer . . . . . . . . . . . . . . . . . . . . . 13
Using the Accessory Hose and the Small
Above-Floor Pocket Tool . . . . . . . . . . . . . . . . . . . . . . . . 14
Caring For Your Steam Cleaner . . . . . . . . . . . . . . . . . . . 15
Ordering Additional Accessories . . . . . . . . . . . . . . . . . 17
Troubleshooting Guide . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Frequently Asked Questions . . . . . . . . . . . . . . . . . . . . . 19
Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
This appliance complies with the WEEE-Directive 2012/19/EU on the disposal of
electrical and electronic equipment (WEEE).
This marking indicates that this product should not be disposed with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact
the retailer where this product was purchased. They can take this product
for environmental safe recycling.
This appliance complies with the European directives for electromagnetic compatibility
(EMC) 2014/30/EU and its revisions, as well as Low Voltage Directive (LVD) 2014/35/EU
and its revisions.
Thank you for purchasing the Shark® Floor and Handheld Steam Cleaner Steam Cleaner.
This Owner’s Guide is designed to help you get a complete understanding of your new
Floor and Handheld Steam Cleaner. Please read it carefully and keep for future reference.
For a list of what is included with this model, refer to inside flap of box.
If you should have a question about your Shark® Floor and Handheld Steam Cleaner
please call Shark® Customer Service at 0800 862 0453.
The Shark® Floor and Handheld Steam Cleaner is a complete solution for both deep
steam cleaning and quick everyday cleaning. Whether you need to clean up tough
stains with the Steam Blaster™ or need to quickly handle a spill, our next-generation
Klik ‘n’ Flip® Mop Head and Dirt Grip™ Pads work with the Steam Cleaner to oer the
ultimate in versatility and eciency, making cleaning simple, quick and easy.
1 20800 862 0453 sharkclean.eu
Page 3
IMPORTANT SAFETY INSTRUCTIONS
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
PLEASE READ CAREFULLY BEFORE USE
WARNING
To reduce the risk of injury, fire, electric shock and property damage
resulting from improper use of the appliance, carefully observe the
following instructions. This unit contains electrical connections and
moving parts that potentially present risk to the user.
DANGER OF SCALDING: THE
STEAM EMITTED FROM THE
STEAM CLEANER IS VERY HOT
AND MAY CAUSE SCALDING.
PLEASE USE CAUTION WHEN
USING THE STEAM CLEANER.
1 This appliance can be used by
persons with reduced physical,
sensory or mental capabilities
or lack of experience and
knowledge if they have been
given supervision or instruction
concerning use of the appliance
in a safe way and understand
the hazards involved. Cleaning
and user maintenance shall not
be made by children. Keep the
appliance and its cord out of
reach of children. Do not allow the
appliance to be used by children.
DO NOT allow to be used as a toy.
Close supervision is necessary
when used near children.
2 Keep the appliance out of reach
of children when it is energised or
cooling down.
3 When in use, NEVER turn the
Steam Cleaner over on its side
or direct steam toward people,
pets or plants. Liquid or steam
must not be directed towards
equipment containing electrical
components, such as the interior
of ovens.
4 The filling aperture should not be
opened during use.
5 Use the system O N LY for its
intended purpose.
6 DO NOT use to heat a room.
7 DO NOT use outdoors.
8 DO NOT leave the Steam Cleaner
unattended when plugged in.
ALWAYS unplug the power cord
from the electrical socket when
not in use and before servicing.
9 DO NOT allow the Steam Cleaner
to be used by children. Close
attention is necessary when used
near children, pets
or plants.
10 Use O N LY as described in this
instruction manual.
11 Use ON LY manufacturer’s
recommended accessories.
12 DO NOT use with damaged cord
or plug. If the Steam Cleaner is not
working as it should or has been
dropped, damaged, left outdoors
or immersed in water, return it
to SharkNinja Operating LLC for
examination and repair. Incorrect
reassembly or repair can cause
a risk of electrical shock or injury
when the Steam Cleaner is used.
13 To protect against a risk of electric
shock, DO NOT immerse the
Steam Cleaner in water or any
other liquid.
14 DO NOT handle the plug or Steam
Cleaner with wet hands or operate
it without wearing shoes.
15 DO NOT pull or carry by cord, use
cord as a handle, close a door on
cord or pull cord around sharp
edges or corners. DO NOT run
Steam Cleaner over cord. Keep
cord away from heated surfaces.
16 DO NOT unplug by pulling on
power cord. To unplug, grasp
the plug, not the power cord.
DO NOT use extension cords or
sockets with inadequate
current-carrying capacity.
17 DO NOT put any objects into
the steam nozzle openings.
Discontinue use if the steam
nozzle is blocked.
18 DO NOT put hands or feet
under the Steam Cleaner. It
gets very hot.
19 Use the floor mop ON LY on flat,
horizontal surfaces. DO NOT use
on walls, counters or windows.
20 DO NOT use on leather, wax-
polished furniture, synthetic
fabrics, velvet or other delicate,
steam-sensitive materials.
21 DO NOT add cleaning solutions,
vinegar, scented perfumes, oils
or any other chemicals to the
water used in the Steam Cleaner
as this may damage it or make
it unsafe for use. If you live in a
hard-water area, we recommend
using distilled water in your
Steam Cleaner.
22 NEVER store or leave Steam
Cleaner in one spot with Dirt Grip™
pad attached, as this may
damage surfaces.
23 Before removing Dirt Grip™ pad,
unplug the Steam Cleaner and
allow it to cool.
24 Unplug the Steam Cleaner before
cleaning. Use a dry or damp cloth
to clean the exterior. DO NOT
pour water on Steam Cleaner
or use alcohol, benzene or paint
thinner to clean.
25 Extreme caution should be
exercised when using the Steam
Cleaner to clean stairs.
26 NEVER use Steam Cleaner without
the Dirt Grip™ pad attached.
27 Keep your work area well lit.
28 Store Steam Cleaner indoors in a
cool, dry place.
29 To avoid circuit overload, DO NOT
operate another appliance on the
same socket (circuit) as the
Steam Cleaner.
30 To avoid scalding injuries,
ALWAYS unplug the Steam
Cleaner and allow it to cool before
removing or changing mop heads,
accessories or Dirt Grip™ pads.
31 Your Steam Cleaner is designed to
clean hard floor surfaces that will
withstand high heat. DO NOT use
on unsealed wood or unglazed
ceramic floors. On surfaces that
have been treated with wax and
on some no-wax floors, the sheen
may be removed by the heat and
steam action. We recommend
testing an isolated area of the
surface to be cleaned before
proceeding. We also recommend
that you check the use and care
instructions from the
floor manufacturer.
3 40800 862 0453 sharkclean.eu
Page 4
GETTING STARTED
WELCOME!
Congratulations
on your purchase.
Use this instruction
manual to learn
about your new
Steam Cleaner’s
great features.
From assembly
to use to
maintenance,
you will find it
all in here.
NOTE: When
assembling your Steam
Cleaner there may be a
little water in or around
the water tank. This is
because we test all our
Steam Cleaners before
you buy them.
CAUTION:
A
B
C
D
E
F
K
N
O
G
H
I
L
M
J
manufacturer/installer for specific information on your surface.
HANDHELD ACCESSORIES
GARMENT STEAMER
WITH BONNET AND BRISTLE FRAME
Ideal for removing wrinkles from clothing
and for freshening and grooming
upholstery.
Do not use this tool without the Microfiber
Bonnet attached.
ACCESSORY HOSE
For optimal range and mobility when
cleaning above-floor surfaces.
SMALL ABOVE-FLOOR POCKET TOOL
AND PAD
Ideal for small, uneven surfaces, corners,
and edges. Do not use without the pad
attached.
Test in a small inconspicuous area and contact your surface
ALSO INCLUDED FOR HANDHELD USE
A Steam Cleaner
Handle
B Upper Cord Wrap
C (1) 6 mm x 54 mm
Large Screw*
D Lower Cord Wrap
E Steam Cleaner
Body
*Flat head screwdriver required. Screwdriver not included.
5 60800 862 0453 sharkclean.eu
F Removable
Handheld Steamer
G Release Button for
Handheld Steamer
H Steam Trigger
I Steam Control
Panel
J Filling Flask
K Mop Head Release
Button
L Dirt Grip™ Pad
Release Buttons
M Steam Blaster™
Nozzle
N Intelli-Mop™ Head
O Dirt Grip™ Pad
1 Concentration
Nozzle
2 Steam Blast
Scrubbing
3 Copper Brush
4 Steam Crevice
tool
1 2 3 4
Page 5
ASSEMBLING YOUR STEAM CLEANER
WARNING :
Always make sure
the Steam Cleaner
is UNPLUGGED
when not in use.
Never fill the Steam
Cleaner or attach
the mop head
when the Steam
Cleaner is plugged
into an electrical
socket. To prolong
the life of your
Steam Cleaner, we
recommend using
distilled water.
Make sure you add
only water to the
tank. Chemicals or
cleaning solutions
(including vinegar)
may damage the
Steam Cleaner
and could be
unsafe for you
and your family.
Fig. 1
Fig. 2b
Fig. 2a
Fig. 3
Fig. 4
Fig. 5
Fig. 6Fig. 4
Fig. 7
Fig. 8
1 Screw the mop
handle into the
Steam Cleaner
body (screwdriver
not included)
(Fig. 1).
7 80800 862 0453 sharkclean.eu
2 Slide the Klik ‘n’ Flip®
Head connector into
the Steam Cleaner
body. Push until you
hear it click securely
into place. (Fig. 1)
To detach the Klik
‘n’ Flip
press the release
button on the front
of the unit above
the head connection
(Fig. 1) and slide o.
mop head,
3 To attach the Dirt Grip™ pad,
spread the pad on the floor with
the pockets face up. Lift the
mop and center the Klik ‘n’ Flip®
Head above the pad, then press
down on the release buttons on
the neck of the Steam Cleaner
head (Fig. 2a). Both sides of the
Klik ‘n’ Flip® Head will drop open
(Fig . 2b). Slip the Klik ‘n’ Flip®
Head’s four corner tabs into the
four corner pockets of the pad
(Fig. 3 and Fig. 4). Gently press
one side of the Klik ‘n’ Flip® Head
to the floor until that side clicks
into place (Fig. 5). Repeat on the
other side (Fig. 6).
4 Open the water tank cap
(Fig. 7), fill the tank with water,
then replace and tighten the cap.
Use the filling flask and pour
water into the tank (Fig. 8).
Do not overfill. Replace
the cap on the water tank.
Page 6
USING YOUR STEAM CLEANER
IMPORTANT: Make
sure you do not use
the Steam Cleaner
without attaching a
Dirt Grip™ pad and
adding water to the
water tank first.
When you are using
the Steam Cleaner
for the first time, it
might take longer
than the normal
30 seconds to
start steaming.
IMPORTANT: Do
not use on unsealed
wood or unglazed
ceramic floors. On
surfaces that have
been treated with
wax and on some
no-wax floors,
the sheen may be
removed by the heat
and steam action.
Test an isolated area
of the surface to
be cleaned before
proceeding. Check
the use and care
instructions from the
floor manufacturer.
NOTE: To prolong
the life of your
Steam Cleaner, we
recommend using
distilled water.
NOTE: Sweep or
vacuum your floors
prior to cleaning
with your Steam
Cleaner.
Fig. 9 Fig. 10
1 Twist the upper cord holder to unwrap the
power cord completely
electrical socket.
2 When it’s first plugged in, the unit will be in
Standby mode. The LO and HI lights below
the Steam Control Button will blink
to indicate Standby mode.
3 To select the steam mode, press the Steam
Control Button once for LO, twice for
HI and 3 times for Standby.
Clean your floors with a forward and
4
backward motion.
5 When you need an extra burst of steam to
clean a stuck-on stain, you can use the
Steam Blaster
so that it is behind the mop body, then
tilt the mop handle down. This will cause
the the Steam Blaster™ (Fig. 10) to emit a
concentrated blast of steam onto the stain.
™
feature. Flip the head over
(Fig. 9)
. Plug into an
Fig. 11a
Fig. 11b
CAUTION: While in Steam
Blaster™ mode, do not leave
stationary for more than one
minute.
CAUTION: Do not scrub any one
area for an extended period
of time.
6 To stop the Steam Blaster™
spray, simply raise the handle.
You can then flip the mop head
back into its original position and
continue cleaning.
When you are done mopping,
7
press the Steam Control Button
until you return to Standby mode
To remove the Dirt Grip™ pad,
8
simply lift the mop straight up by
the handle until the Intelli-Mop
Head is hanging straight down.
Press down on the pad release
buttons on the neck of the mop
head
(fig 11a),
the head will drop open, releasing
the pad
and both sides of
(fig 11b)
.
9
Once the Dirt Grip™ pad has been
rel
eased, close the Intelli-Mop™
Head. To close, gently p
side of the
the floor until that side clicks into
place. Repeat on the other side.
10 When the water tank is empty,
the Steam Cleaner will stop
producing steam. You can refill
the water tank at any time as
long as the Steam Cleaner is
unplugged. Follow the water
tank filling instructions on
page 7.
NOTE:
.
for the Steam Cleaner to cool o
before switching the mop head.
™
Never leave the Steam Cleaner
with a damp or wet Dirt Grip™
pad on any floor for an extended
period of time.
Intelli-Mop™ Head
Please wait 2 to 3 minutes
ress one
to
9 100800 862 0453 sharkclean.eu
Page 7
INTELLIGENT STEAM CONTROL
ABOVE-FLOOR CLEANING
The Shark Steam
Cleaner has 3 unique
Intelligent Steam
Control settings so
you can use the right
amount of steam for
the cleaning task at
hand.
See below for
tips on when to
use each setting.
* Sanitisation studies
were conducted
under controlled
test conditions.
Household conditions
and results may vary.
With Klik ‘n’ Flip®
Mop in HI mode
only when used with
Steam Cleaner.
Not in Steam
Blaster™ mode.
Setting Ideal For These
TOOLS
LO
HI
Sealed Surfaces
Laminate
Hardwood
Marble
Hardwood
Marble
Tile
Stone
Hardwood
Marble
Tile
Stone
Steam
Blaster
For an extra burst of steam, you can
use the Steam Blaster™ feature in LO or
™
HI. Follow the instructions found on the
“Using your Steam Cleaner” page.
Recommended
Usage
Cleaning delicate
surfaces.
Light cleaning and
dusting.
Loosening and
lifting light dirt.
Cleaning most
surfaces and large
areas.
Basic, everyday
cleaning.
Removing spots and
smaller messes.
Cleaning moderate
and heavy-trac
areas.
Deep-cleaning and
cleaning hard-toclean surfaces.
Tough cleaning and
removing stuck-on
messes and stains.
Deep-cleaning
heavy-trac areas.
Cutting through
heavy dirt
and grime.
Sanitizing* floors.
TO SANITIZE* WITH THE STEAM CLEANER USING THE
INTELLI-MOP™ HEAD AND THE DIRT GRIP™ PAD:
1 Attach a clean Dirt Grip™ pad to the mop head.
2 Plug in the unit and press the Steam Control Button
to select the HI Setting.
3 Wait 30 seconds for the unit to begin producing
steam.
4 Start mopping on an appropriate sealed hard floor
surface with a forward and backward motion. After
three minutes, your unit is ready to be used to sanitize.
5 Using a forward and backward motion, move the
unit over the area you seek to sanitize. Repeat at
least 5 times.
For a full list of what
is included with your
Steam Cleaner, please
refer to box’s top panel.
The Shark® Floor and Handheld Steam
Cleaner is designed to clean surfaces that can
withstand high heat and moisture. Do not use
on unsealed wood surfaces (especially antique
wood furniture), unglazed ceramic tile, painted
surfaces, or surfaces that have been treated
with wax, oils, varnishes, or shellac. The sheen
may be removed by the heat, steam, and
friction of the cleaning accessories. It is always
recommended to test an isolated area of the
surface to be cleaned before proceeding.
We also recommend you check the use and
care instructions from the surface manufacturer.
When cleaning finished wood surfaces, use
broad, continuous strokes. To prevent surface
damage, avoid focusing steam or allowing the
cleaning accessories to remain stationary in any
one spot.
Fig. 12
• Remove the Handheld Steamer by pressing
on the release button and pulling away from
the cradle.Be careful to NOT press the steam
trigger as you remove the handheld steamer.
(Fig. 12).
• The Handheld Steamer is automatically set
to TOOLS mode. Squeeze the steam trigger
to activate steam. You may select other
steam modes depending on the accessory
and the use.
• With all attachments, control Steam better by
using 3-to-5-second bursts of the trigger. This will
allow you to steam longer and with more control.
11 120800 862 0453 sharkclean.eu
Page 8
USING THE GARMENT STEAMER
Certain models only
For a full list of what
is included with your
Steam Cleaner, please
refer to box’s top panel.
CAUTION:
Make sure the
Handheld Steamer
is unplugged or
in Standby mode
while attaching
or removing the
accessory. Avoid
touching the
accessory, as it
will be very hot
after steaming.
CAUTION: To
avoid scalding
injuries, always
unplug and
allow the Steam
Cleaner to cool
before removing
or changing
accessories
or pads.
How to Attach/Detach:
• Use the lavender loop on the side of the
• Snap the bristle frame over the bonnet with
• Attach the assembled Garment Steamer to the
• To remove, wait 2 to 3 minutes for the tool to
Usage:
• The Garment Steamer is ideal for removing
• The bonnet and frame with bristles provide
Cleaning Tips:
• Pressing the steam trigger in 3-to-5-second
• Always determine color fastness of any fabric,
– Take a clean, moist, warm towel and gently
– If color bleeds onto the towel, you may need
Fig. 15
Fig. 17
bonnet to slide over the nozzle opening of the
Garment Steamer. (Fig. 15).
the bristles placed at the top of the Garment
Steamer bonnet.
Handheld Steamer by snapping it into the main
nozzle. (Fig. 16).
cool, hold the release button and pull the tool
away from the unit.
wrinkles from clothing and for freshening and
grooming upholstery.
controlled steaming for fabrics and upholstery.
bursts, move slowly up and down over your
garments or upholstery. (Fig. 17).
especially with reds or blues:
rub a small area on the fabric that is as out of
sight and out of the way as possible.
to have the piece professionally cleaned.
Fig. 16
USING THE ACCESSORY HOSE AND THE
SMALL ABOVE-FLOOR POCKET TOOL
For a full list of what
is included with your
Steam Cleaner, please
refer to box’s top panel.
CAUTION: Make
sure the Handheld
Steamer is
unplugged or in
Standby mode
while attaching
or removing the
accessory. Avoid
touching the
accessory, as it will
be very hot after
steaming.
CAUTION:
To avoid scalding
injuries, always
unplug and
allow the Steam
Cleaner to cool
before removing
or changing
accessories or pads.
Fig. 20
How to Attach/Detach:
• First attach the Accessory Hose to the
Handheld Steamer by snapping the Accessory
Hose into the main nozzle. (Fig. 18).
• Slide the pad over the Small Above-Floor Pocket
Tool so it fits snugly. Attach the elastic band and
slide the locking toggle to securely tighten the
pad over the tool.
• Connect the Small Above-Floor Pocket Tool to
the steam nozzle at the end of the accessory
hose. Slide the base of the tool over the tip of
the nozzle until the tool clicks securely into
place. (Fig. 19).
• Do not use the Small Above-Floor Pocket Tool
without the pad attached.
• To remove, wait 2 to 3 minutes for the tool to
cool, hold the release button and pull the tool
away from the unit.
Usage:
• The Small Above-Floor Pocket Tool is ideal for
small, uneven surfaces. The pointed tip is great
for edges and corners. (Fig. 20).
Cleaning Tips:
• Additional attachments are available for your
accessory hose. Please visit
sharkaccessories.com for more information.
Fig. 19Fig. 18
14sharkclean.eu13 0800 862 0453
Page 9
CARING FOR YOUR STEAM CLEANER
Fig. 23
Dirt Grip™ Pad Care InstructionsCare
Machine-wash the Dirt Grip™ pads separately
with warm water using liquid detergent.
NEVER USE BLEACH, POWDERED DETERGENT,
OR FABRIC SOFTENERS as they may damage
or leave a coating on the Dirt Grip™ pads that
will reduce their cleaning performance and
absorbency. Dirt Grip™ pads should be line-dried
or tumble-dried on a low setting, as this will
Fig. 22Fig. 21
After Use and Storage
1 Press the Steam Control Button until it starts
to blink, indicating that you are in Standby
mode. Unplug the cord from the socket and
place the Steam Cleaner into the upright
position. Let it cool.
2 To remove the Dirt Grip™ pad, lift the Steam
Cleaner straight up by the handle until the
Intelli-Mop™ Head is hanging straight down.
Press the pad release buttons on the neck of
the mop head, and both sides of the IntelliMop™ Head will drop open, releasing the pad.
Once the pad has been released, close the
Intelli-Mop™ Head.
3 If the Intelli-Mop™ Head is not attached to the
mop, the pad can still be removed. Press down
on the release button on the Intelli-Mop™ Head
post to release the pad (Fig. 21).
4 Empty the water tank before storing. To empty
the tank, hold the Steam Cleaner beside a sink.
Open the water tank lid, then lean the unit
over the sink. Let the water drain out, then
close the lid.
5 To store the Steam Cleaner, wait until after it
has cooled and the steam has been released.
15 160800 862 0453 sharkclean.eu
extend the life of the microfiber fabric
(Fig. 23).
Loose fibers can indicate wearing of the
microfiber fabric. Do not pull the loose fibers, as
this can cause the weave to come undone. Simply
trim the loose fibers with scissors (Fig. 24).
Fig. 24
Replacement Dirt Grip™ pads
For best cleaning results, we recommend
replacing your Dirt Grip™ pads every 3 to 4
months following normal use. As with any fabric,
dirt particles, grease, friction, and repeated
washing can cause the fibers to break down, and
you may notice an increase in the eort needed
to push or pull the mop.
You can purchase replacement Dirt Grip™ pads and
other accessories by visiting sharkclean.eu/parts
and accessories or calling 0800 862 0453.
Steam Nozzle Care
If you believe the main steam nozzle or the
Steam Blaster™ nozzle is clogged, please
contact Customer Service at 0800 862 0453 or
sharkclean.eu.
Page 10
ORDERING ADDITIONAL ACCESSORIES TROUBLESHOOTING GUIDE
ACCESSORY
Intelli-Mop™ Head
Great for all-purpose cleaning. Get an extra boost for
tough stains from the Steam Blaster™, and clean twice
the area with the hands-free two-sided pad.
Dirt Grip™ Pad
Double-sided pad. Easy, hands-free installation and
removal. Washable and reusable.
Triangle Scrubber Head
Triangle shape is perfect for cleaning corners and
hard-to-reach areas. Equipped with a Steam Blaster™
to help loosen stains and stuck on dirt.
Triangle Scrubber Pad
Ideal for cleaning corners and other hard-to-reach
spaces. Easy to install and remove.
WARNING: To reduce the risk of shock and unintended operation,
turn o power and unplug unit before servicing.
The Steam Cleaner isn’t producing any steam.
• The Steam Cleaner should be securely plugged into an electrical socket.
Check your fuse or circuit breaker or try a dierent socket.
• Make sure the water tank is full, the unit is plugged in, and the light around
the Steam Control Button is solid.
• If the lights below the Steam Control Button are not illuminated, try a
dierent electrical socket.
• If the lights below the Steam Control Button are blinking, press the Steam
Control Button to select a Steam setting.
• If the lights below the Steam Control Button are solid, wait 30 seconds for
the unit to warm up.
• If after following the above steps the Steam Cleaner still does not produce
any steam, contact Customer Service at 0800 862 0453 or sharkclean.eu
The Steam Cleaner is producing intermittent steam.
• This is normal—for more consistent steam select the HI setting.
• Also make sure the water tank is full.
I can’t select a Steam Setting.
• Make sure the Steam Cleaner is plugged in and the lights below the Steam
Control Button are solid.
• If your Steam Cleaner is producing steam but the lights below the Steam
Control Button are not lit, call customer service at 0800 862 0453.
I am getting streaky/cloudy floors.
• The Dirt Grip™ pad might be dirty. If it is, flip it over to the clean side
or change it entirely. If you washed the Dirt Grip™ pad with powdered
detergent, then it could be damaged and require replacement.
• This could also be an indication of soap or grease residue that has
accumulated on the floor. As the Steam Cleaner uses only a small amount of
water, it may not be enough to rinse o the accumulation of residue that the
steam is bringing to the surface. We suggest rinsing the floor with nothing
but water, letting it dry, and then steam clean again with a clean Dirt Grip™
pad. One or more rinses will generally remove the residue.
• A more stubborn case may require you to rinse the floor with a mix of one
part vinegar and two parts water* (but DO NOT put vinegar or any other
cleaner into the Steam Cleaner’s water tank.)
• *Please consult your flooring manufacturer’s care and maintenance
instructions before applying any cleaning products or solutions
including vinegar.
17 180800 862 0453 sharkclean.eu
Page 11
FREQUENTLY ASKED QUESTIONS WARRANTY TERMS
AND CONDITIONS
What surfaces can I use the Steam Cleaner on?
• The Steam Cleaner is designed for use on all sealed hard floor surfaces.
We recommend that you first test an isolated area of the floor surface
to be cleaned as well as review the use and care instructions from your
floor manufacturer.
• CAUTION : Do not use on leather, wax-polished furniture, synthetic
fabrics, velvet, or other delicate, steam-sensitive materials.
• NOTE: On surfaces treated with wax and on some no-wax floors, the
sheen may be removed by the heat or steam action of the unit. Test an
isolated area of flooring first to see if sheen is aected.
Can I put something other than water in the water tank of the Steam
Cleaner?
• DO NOT add cleaning solutions, scented perfumes, oils, or any other
chemicals to the water used in this appliance, as this may damage the
unit or make it unsafe for use. We recommend using distilled water in
your Steam Cleaner.
When a consumer buys a product in the UK, they get the benefit of legal rights relating to the quality of the
product (your “statutory rights”). You can enforce these rights against your retailer. However, at Shark® we
are so confident about the quality of our products that we give the original product owner an additional
manufacturer’s warranty of up to two years. (1 year as standard plus 1 year when you register) These terms
and conditions relate to our manufacturer’s warranty only – your statutory rights are unaected. Please note
that the 2 year guarantee is available in all EU countries and in the UK if it stops being an EU country during
the guarantee term.
The conditions below describe the prerequisites and scope of our warranty. They do not aect your
statutory rights or the obligations of your retailer and your contract with them.
Shark
Guarantees
A household appliance like a Steam Cleaner constitutes a sizeable investment. Your new machine needs
to work properly for as long as possible. The guarantee it comes with is an important consideration - and
reflects how much confidence the manufacturer has in its product and manufacturing quality.
Every Shark® machine comes with a free parts and labour guarantee. Our customer service helpline
(0800 862 0453) is open from 9.00am to 6.00pm Monday - Friday. It’s free to call, and you’ll be put straight
through to a Shark® representative. You’ll also find online support at www.sharkclean.eu/uk.
How do I register my extended Shark
You can register your guarantee online within 28 days of purchase. To save time, you’ll need the following
information about your machine:
• Date you purchased the machine (receipt or delivery note)
• To register online, please visit www.sharkclean.eu/uk/register-guarantee
IMPORTANT
• Both the 12 months and the extended 1 year guarantee will only cover your product from the date of
purchase.
• Please keep your receipt at all times. Should you need to use your extended guarantee we will need your
receipt to verify the information you have supplied to us is correct. The inability to produce a valid receipt
may invalidate your guarantee.
What are the benefits of registering my free Shark
When you register your guarantee we’ll have your details to hand if we ever need to get in touch. If you
further agree to receive communications from us, you can also receive tips and advice on how to get the
best out of your Shark® Steam Cleaner and hear the latest news about new Shark® technology and launches.
If you register your guarantee online, you’ll get instant confirmation that we’ve received your details.
How long are new Shark
Our confidence in our design and quality control means that your new Shark® Steam Cleaner is guaranteed
for a total of up to two years for the original owner (12 months plus an extended warranty of 1 year).
What is covered by the free Shark
Repair or replacement of your Shark® machine (at Shark’s discretion), including all parts and labour. A Shark®
guarantee is in addition to your legal rights as a consumer.
What is not covered by the free Shark
• Normal wear and tear.
• Accidental damage, faults caused by negligent use or care, misuse, neglect, careless operation or handling
of the Steam Cleaner which is not in accordance with the Shark® Operating Manual supplied with your
machine.
• Use of the Steam Cleaner for anything other than normal domestic household purposes.
• Use of parts not assembled or installed in accordance with the operating instructions.
• Use of parts and accessories which are not Shark® Genuine Components.
• Faulty installation (except where installed by Shark®).
• Repairs or alterations carried out by parties other than Shark® or its agents.
What happens when my guarantee runs out?
Shark® does not design products to last for a limited time. We do appreciate that there may be a desire for
our customers to want to repair their Steam Cleaner cleaners after the warranty has elapsed or the product
has been sold to a new owner. In this case please contact our free phone customer service help line and ask
about our out warranty program, on 0800 862 0453.
Where can I buy genuine Shark
Shark® spares and accessories are developed by the same engineers who developed your Shark® Steam
Cleaner. You’ll find a full range of Shark® spares, replacement parts and accessories for all Shark® machines at
www.sharkclean.eu.
Please remember that using non-Shark® spares invalidates your guarantee.
machines guaranteed for?
guarantee?
guarantee?
guarantee?
guarantee?
spares and accessories?
20sharkclean.eu19 0800 862 0453
Page 12
NOTES NOTES
21 220800 862 0453 sharkclean.eu
Page 13
NOTE: Save these instructions. Keep for future reference.
This marking indicates this product should not be disposed of with other
household wastes throughout the EU. To prevent possible harm to the
environment or human health from uncontrolled waste disposal, recycle it
responsibly to promote the sustainable reuse of material sources. To return
your used device, please use the return and collection systems or contact
the retailer where this product was purchased. They can take this product
for environmentally safe recycling.
Euro-Pro Europe Limited
3150 Century Way
Thorp e Park
Leeds
LS15 8ZB
0800 862 0453
sharkclean.eu
Illustrations may dier from actual product. We are constantly striving
to improve our products, therefore the specifications contained herein
are subject to change withoutnotice.
©2019 SharkNinja O perating LLC. SHARK, KLIK ‘N’ FLIP, INTELLIGENT STEAM
CONTROL and STEAM POCKET are registered trademarks of SharkNinja
Operating LLC . LIF T-AWAY, INTELLI- MOP HEAD, STEAM BL ASTER and
DIRT GRIP
S6005UK_Series_IB_MP_191213_MV1
PRINTED IN CHINA
are trademarks of
SharkNinja Operating LLC.
IPX4
@sharkcleaninguk
@sharkcleanuk
@sharkcleanuk
Loading...