Shark FA200 User Manual

Download

Page 1

FAN

FA200 Series

OWNER’S GUIDE

Page 2

IMPORTANT SAFETY INSTRUCTIONS

SUITABLE FOR OUTDOOR USE & HOUSEHOLD USE ONLY.

IMPORTANT SAFETY INSTRUCTIONS

SUITABLE FOR OUTDOOR USE & HOUSEHOLD USE ONLY.

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY: READ ALL THESE INSTRUCTIONS BEFORE USE.

This appliance is operated by a rechargeable battery. ONLY

recharge the battery with the charger supplied with the unit, battery charger for use only with model GQ36-120300-AUO power supply from Dongguan Gangqi Electronics Co., Ltd. or with model AJJ3-1 from Anlian. A charger that may be suitable for one type of battery may create a risk of ﬁre when used with another battery.

2. Do not attempt to destroy, remove, or disassemble the battery

pack from the machine. Do not incinerate battery cells. Consult your local waste authority for information regarding available recycling and/or disposal options.

3. This appliance comes with a remote control which contains

a coin battery. Dispose of batteries properly. Always keep batteries away from children (choke hazard). Even used batteries can cause injury.

4. To reduce the risk of electric shock, connect only to an outlet

provided with a ground fault circuit interrupting (GFCI) device.

5. The fan should be used on a stable and level surface.

6. Never use this fan near pools, bathtubs, showers, basins, or

other vessels containing water.

7. Do not operate any unit with a damaged power supply wire

or battery charger. Discard the unit or return to an authorized service facility for examination and/or repair.

8. Do not run cord under carpeting. Do not cover charge cord

with throw rugs, runners, or similar coverings. Do not route charger cord under furniture or appliances. Keep charger cord away from high-trac areas. Place charger in an area where the cord will not be tripped over.

9. If the charger cord is damaged, it should be replaced.

10. This appliance is not intended for use by anyone (including

children) with reduced physical, sensory, or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

11. Children should be supervised to ensure that they DO NOT play

with the appliance.

12. Cleaning and user maintenance shall not be made by children

without supervision.

13. Prior to cleaning or other maintenance, the appliance must be

unplugged from the electrical outlet.

14. Only use Shark branded accessories.

15. Do not use if appliance is not working as it should, or has been

dropped, damaged, left outdoors, or dropped into water.

16. Turn o all controls before plugging in or unplugging the

appliance.

17. Unplug from electrical outlet when not in use and before any

maintenance or cleaning.

18. Hand wash exterior/hard plastic/non-electronic parts with

water only. Do not immerse. Cleaning with chemicals could damage the unit.

19. Do not attempt to repair or adjust any electrical or mechanical

functions of this appliance, as this may cause danger and void the warranty.

BATTERY WARNINGS

1. Remove and immediately recycle or dispose of used batteries

according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.

2. Even used batteries may cause severe injury or death.

3. Call a local poison control center for treatment information.

4. Compatible battery type is CR2025.

5. The nominal battery voltage is 3V.

6. Non-rechargeable batteries are not to be recharged.

WARNING

• INGESTION HAZARD: This product contains a button cell or coin battery.

• DEATH or serious injury can occur if ingested.

• A swallowed button cell or coin battery can cause Internal Chemical

Burns in as little as 2 hours.

• KEEP new and used batteries OUT OF REACH of CHILDREN.

• Seek immediate medical attention

if a battery is suspected to be swallowed or inserted inside any part of the body.

7. Do not force discharge, recharge, disassemble, heat above (manufacturer's speciﬁed temperature rating) or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.

8. Ensure the batteries are installed correctly according to polarity (+ and -).

9. Do not mix old and new batteries, dierent brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.

10. Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.

11. Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

WARNING: Not suitable for use with solid-state

speed controls.

LITHIUM BATTERY SAFETY WARNINGS

LITHIUM BATTERIES STORE A LARGE AMOUNT OF ENERGY AND WILL VENT FIRE OR EXPLODE IF MISTREATED.

1. DO NOT DO ANY OF THE FOLLOWING TO THE BATTERY PACK:

a. Open d. Puncture b. Drop e. Incinerate c. Short-circuit f. Expose to temperatures

2. Keep battery pack dry.

3. Charge battery pack only according to its charger's

instructions.

4. Inspect battery pack before every use: do not use or charge if damaged.

BATTERY REMOVAL AND DISPOSAL

This product contains an integral lithium battery (not replaceable), and the remote control uses a lithium coin battery. When the remote battery no longer has a charge, it should be removed from the remote and recycled. DO NOT incinerate or compost the product with its integral battery or the remote battery. When your remote battery needs to be replaced, dispose of it or recycle it in accordance with local ordinances or regulations. In some areas, it is illegal to place spent lithium batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop o the spent battery.

POWER SUPPLY SAFETY

1. Read and follow all instructions that are on the product

or provided with the product.

2. Do not use an extension cord.

3. Do not use within 10 feet of pool and do not use in

a bathroom.

4. WARNING: Risk of Electric Shock. When used outdoors, install

only to a covered Class A GFCI protected receptacle that is weatherproof with the power unit connected to the receptacle. If one is not provided, contact a qualiﬁed electrician for proper installation. Ensure that the power unit and cord do not interfere with closing the receptacle cover.

FCC WARNINGS

Note: This equipment has been tested and complies with the limits for a

Class B digital device - pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. To see if this equipment interferes with radio or television reception, try turning the equipment o and on. To correct any interference:

• Reorient or relocate the receiving antenna.

• Increase the distance between the equipment and the receiver.

• Connect the equipment to a dierent outlet than the receiver.

• Consult the dealer or an experienced technician for help.

This device complies with Part 15 of the FCC Rules. Operation is subject to two conditions:

1. This device may not cause harmful interference, and

2. this device must accept any interference received, including interference

that may cause undesired operation. Caution: Any changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

WARNING: Not for use with receptacles that are weatherproof only when

the receptacle is covered (attachment plug cap not inserted and receptacle cover closed)

WARNING: RISK OF ELECTRIC SHOCK. MOUNT THE UNIT AT A HEIGHT

GREATER THAN 0.3 M FROM THE GROUND SURFACE.

WARNING: Contains coin battery.

CAR CHARGER

1. SAVE THESE INSTRUCTIONS.

This manual contains important safety and operating instructions for battery charger model FA20XCAR from Dongguan City Gangqi Electronics Co., Ltd.

2. Before using this battery charger, read all instructions and cautionary markings on the battery charger, battery, and product using battery.

3. CAUTION: To reduce risk of injury, charge only the provided rechargeable battery. Other types of batteries may burst, causing injury to persons and damage.

4. Do not expose charger to rain, moisture, or snow.

5. Use of an attachment not recommended or sold by the

battery charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

6. To reduce damage to car charger and cord, do not attempt to remove the charger from the outlet by pulling the cord. Pull the entire car charger connection from the outlet.

7. To reduce risk of electric shock, unplug charger before attempting any maintenance or cleaning. Turning off controls will not reduce this risk.

8. Do not operate the car charger if any components are damaged.

9. To clean the charger, first unplug it, then gently wipe it with a damp cloth. Allow the charger to air-dry completely before using it.

10. The charger uses a replaceable 5-amp fuse. To remove the fuse, unscrew the chrome knob at the tip of the charging plug. Use only 5-amp fuses for replacement.

MISTING ACCESSORY

1. The misting accessory is suitable for OUTDOOR USE ONLY.

2. The misting accessory will continue to operate when the

fan is powered off. Turn off the water source to turn off the accessory.

3. DO NOT operate the misting accessory using water pressure above typical household pressure, 60 psi.

4. DO NOT use warm or hot water. Only use cold or room temperature water.

5. DO NOT handle live electrical products while in range of the misting stream.

FAN COVER

READ ALL INSTRUCTIONS BEFORE USE

The fan cover is not a toy. Children should not play with it as it may become unsanitary during outdoor use.

6. Keep non-waterproof electronic equipment and appliances out of the misting stream.

7. Children should be supervised to ensure that they DO NOT play with the misting accessory.

8. WARNING: CHOKING HAZARD. Always keep nozzles and

any other small parts out of the reach of children.

9. Cleaning and user maintenance of the misting accessory shall not be done by children without supervision.

BATTERY RE MOVAL AND DISPOSAL:

When the remote battery no longer has a charge, it should be removed from the remote and recycled. Contact your local recycling center for information on where to drop o the spent battery. If the integral fan battery is no longer able to be recharged, it should be recycled. Return un-rechargeable fan (w/integrated battery) to an authorized recycling center or to retailer for recycling, or contact your local recycling center for information on where to drop o spent batteries. DO NOT incinerate or compost the product with its integral battery or the remote battery.

This product contains an integral lithium battery (not replaceable), and the remote control uses a lithium coin battery.

READ AND SAVE THESE INSTRUCTIONS

Page 3

WHAT’S INCLUDED

ASSEMBLING YOUR FAN

Base

Pole

Fan Head

(already assembled)

1 A

Upper pole

The upper pole

has wider end.

1. Align and insert the

Upper Pole into the Lower Pole until it

clicks into place.

Align yellow arrow on

bottom of pole with

yellow dot on base

Align the yellow dot on the assembled pole with the yellow arrow on the Base, then slide the pole down onto the base. Make sure the pole is installed completely and securely.

Rotate clockwise to

tighten the bolt.

3. Turn the base on its

side, then insert the Bolt in the bottom of the Base. Use the Allen wrench to rotate the bolt on the bottom of the base. Rotate the bolt counterclockwise to loosen it, then remove it.

FEATURES

4. CAUTION: ﬁnger pinch

risk. Holding the fan by the handle, insert the the legs of the fan head into the top of the assembled pole until

they click into place.

Charging port labeled

with

5. Charge fan to 100%

battery power before use without the cord. First use: before using remote control, press Power Button on fan. Fan is operable while charging.

Allen Wrench

Remote ChargerBolt

ACCESSORIES

Dierent fan models come with dierent accessories. To purchase an accessory that was not included, go to sharkclean.com

CORDLESS OUTDOORS BREEZEBOOST™

This is a 2-in-1 fan that can be used with or without the cord.

This fan can be enjoyed indoors or outdoors.

DO NOT CHARGE OR USE IN THE RAIN.

OSCILLATION

This fan oers up to 180 degrees of oscillation as well as up to 55 degrees of vertical tilt.

Activate the extra-powerful BreezeBoost™ for maximum-strength airﬂow.

HOW TO USE YOUR FAN

Press between fan speeds. LED lights will indicate selected fan speed.

Fan Speeds

BreezeBoost™

Press

Oscillation

between oscillation settings. LED lights will indicate which setting is selected.

Horizontal Angle Adjust

Press the < of the fan at a distance.

MAXIMUM CORDLESS RUNTIME: 24 hours on fan speed 1.

Runtime

MAXIMUM CORDLESS PERFORMANCE: 2 hours on fan speed 5. PLUGGED IN: Indeﬁnite runtime; fan will charge while operating.

Charge Time FROM 0% TO FULLY CHARGED BATTERY: 5 hours

Battery Indicator

on the fan head or < > arrows on the remote to switch

For maximum-strength airﬂow, press and hold on the

Mode

fan head for 3 seconds, or press cordless use, fan speed will automatically decrease after

on the remote. During

20 minutes to save battery power.

on the fan head or < > arrows on the remote to toggle

> arrows on the remote to change the horizontal angle

100% charged: white light 51%-99%: green light 21%-50%: amber light

6%-20%: red light steady

5% and below: red light blinking

REMOTE STORAGE

Store the remote on the back of the fan head when not in use.

To preserve battery life, the

fan will enter IDLE mode if left

unplugged and powered o for

24 hours. In IDLE mode, the

remote cannot be used to turn

on the fan. To turn o IDLE

mode, press the power button

on top of the fan head.

Mister

Car Charger Cover

Page 4

CHARGING THE FAN

TABLETOP MODE

To convert the fan to portable, tabletop mode:

PEDESTAL MODE: To charge the fan in pedestal mode, insert the CHARGER PLUG into the charging port near the bottom of the POLE.

TABLETOP MODE: To charge the fan in tabletop mode, insert the CHARGER PLUG into the charging port under the center shaft of the fan, between the 4

support legs. DO NOT CHARGE OR USE IN THE RAIN.

Dierent fan models have dierent speed selections. See the charts below for runtime for the 5-speed model and the 3-speed model.

BATTERY LIFE - 5 FAN SPEEDS

Settings Runtime

Fan Speed 1 24.0 hours

Fan Speed 1

+ Oscillation

Fan Speed 2 14.0 hours

Fan Speed 2 + Oscillation

Fan Speed 3 6.3 hours

Fan Speed 3 + Oscillation

10.0 hours

7.5 hours

4.5 hours

Settings Runtime

Fan Speed 4 3.5 hours

Fan Speed 4 + Oscillation

Fan Speed 5 2.0 hours

Fan Speed 5 + Oscillation

BreezeBoost™ Mode 1.5 hours

BreezeBoost™ Mode

+ Oscillation

2.5 hours

1.7 hours

1.3 hours

Runtime subject to 10% variability.

To detach the fan from the pole, press the Lift-Away button, then slide the fan head off the pole.

1. Release the fan head by pressing the lift away button and carefully remove the fan from the pole.

DISASSEMBLY

2. Turn the pedestal base on its side to access the bolt on the bottom. Use the included Allen wrench to rotate the bolt counterclockwise, then remove the bolt.

Spread out the four support legs until they click into place. Place the fan on a flat, level surface and begin use.

3. Carefully lift the pole to remove it from the base.

4. Press the small button on the lower pole to detach the poles from one another. Carefully fold as needed for storage. DO NOT strain the cord.

BATTERY LIFE - 3 FAN SPEEDS

Settings Runtime

Fan Speed 1 24.0 hours

Fan Speed 1

+ Oscillation

Fan Speed 2 6.3 hours

Fan Speed 2 + Oscillation

10.0 hours

4.5 hours

Settings Runtime

Fan Speed 3 2.0 hours

Fan Speed 3 + Oscillation

BreezeBoost™ Mode 1.5 hours

BreezeBoost™ Mode

+ Oscillation

1.7 hours

1.3 hours

Runtime subject to 10% variability.

If grill screw, bolt, or Allen wrench have been lost, see Hardware Specs section for information on how to replace any hardware.

STORAGE

STORAGE TYPE INSTRUCTIONS

1. Carefully disassemble the fan OR place the assembled fan in the desired storage location. Ensure it is out of reach of children and pets.

Short-term storage indoors (<24 hours)

Long-term storage indoors (>24 hours)

2. Place the assembled fan in the desired storage location. Ensure it is

out of the reach of children and pets. If there is inclement weather, it is recommended to bring fan indoors.

1. Carefully disassemble the fan OR place the assembled fan in the desired storage location. Ensure it is out of reach of children and pets.

2. Store the fan indoors when not in use for long periods of time. Ensure it is

stored out of reach of children.

Page 5

SETTINGS

FAN SPEEDS

• Before ﬁrst use, pull out the plastic tab from the battery compartment of the remote control.

• To preserve battery life, the fan will enter IDLE mode if left unplugged and powered o for 24 hours. In IDLE mode, the

remote cannot be used to turn on the fan. To turn o IDLE mode and turn on the power, press the power button on top of the fan head.

• The LED lights on the fan head display will only remain illuminated for 20 seconds after a setting adjustment is made, before turning o to save battery.

• For information on how to activate or deactivate LOCK MODE for fan maintenance, please see the Maintenance section.

• Remote may be less eective when used outdoors.

POWER ON/OFF

To turn the fan on or o, press the POWER button on the remote or the POWER button on the fan head.

5-SPEED MODELS DISPLAY

LED animations will play once

(LEDs will turn on from left to right, then turn o from right to left)

Changing the FAN SPEED will increase or decrease the airﬂow of the fan. There are 5 fan speed settings.

To change the speed, press the fan icon on the fan head to cycle though the dierent speeds. With the remote, press the up or down arrows to change speeds.

SPEED DISPLAY

(5-SPEED MODELS)

BEST FOR

Quiet operation

Moderate cooling

Balance of noise level and fan power

Air circulation

High power cooling

OFF

LEDs will turn o

3-SPEED MODELS DISPLAY

LED animations will play once

(LEDs will turn on from left to right, then turn o from right to left)

OFF

LEDs will turn o

Hold for 3 seconds

SPEED DISPLAY

(3-SPEED MODELS)

BEST FOR

Quiet operation

Balance of noise level and fan power

High power cooling

BREEZEBOOST™ MODE

Turn on BreezeBoost for maximum-power airﬂow. When operating cordlessly, BreezeBoost will automatically turn o after 20 minutes to save battery. BreezeBoost will run indeﬁnitely when the fan is plugged in.

To activate BreezeBoost, press the UP ARROW button on the REMOTE or press and hold the fan icon on the fan head for 3 seconds. Repeat to manually deactivate BreezeBoost.

DISPLAY

(5-SPEED MODELS)

SPEED BEST FOR

LED animation will repeat 5 times

(LEDs will turn on from left to right)

DISPLAY

LED animation will repeat 5 times

(LEDs will turn on from left to right)

(3-SPEED MODELS)

BreezeBoost

Maximizing

fan power

SPEED BEST FOR

BreezeBoost

Maximizing

fan power

Page 6

OSCILLATION

Choose between oscillation settings to best suit your needs. 5-speed models have 3 options for angle of oscillation, while 3-speed models have one option.

To change the oscillation settings, press the up/down arrow on the REMOTE. To do so on the fan head, press the oscillation

To turn o oscillation, press the down arrow on the remote or the oscillation head until no LEDs are illuminated.

DISPLAY

(5-SPEED MODELS)

icon to cycle through the settings.

ANGLE BEST FOR

45°

90°

180°

Circulating air in small area,

Circulating air in moderate

area, 3-4 people

Circulating air in large area,

icon on the fan

1-2 people

5+ people

CLEANING THE FAN

Why is the remote not working?

Why are the remote and UI buttons not working?

When using the remote control, make sure it is pointed directly at the LEDs on the front of the fan.

The fan may have entered IDLE mode. To preserve battery life, the fan will enter IDLE mode if left unplugged and powered o for 24 hours. In IDLE mode, the remote cannot be used to turn on the fan. To turn o IDLE mode and turn on the power, press the power button on top of the fan head.

If the remote still doesn’t work, then try replacing the batteries in the remote.

Make sure the fan has battery power by pressing the Power button. If the Battery LED indicator blinks red, then the fan needs to be charged.

The fan may be in Lock mode, which deactivates the fan to allow you to safely maintain it. To turn o Lock mode, press the Oscillation ( 3 seconds.

) icon on the fan and hold it down for

DISPLAY

(3-SPEED MODELS)

ANGLE BEST FOR

180°

Circulating air in large area,

5+ people

HORIZONTAL ANGLE ADJUST

You can use the remote control to change the horizontal angle of the fan from a distance. Press the left or right arrows on the remote to adjust the horizontal angle.

Why is the battery light ﬂashing

GENERAL USE

red when I am trying to turn on BreezeBoost™ mode?

Can I leave the fan outdoors?

Why is the fan rattling?

The second LED indicator and the Battery LED (in amber) are ﬂashing. What is wrong?

Why do I have to activate Lock mode before maintenance?

How often should I clean the fan?

MAINTENANCE

If the battery level is under 10%, BreezeBoost mode cannot be activated. Charge the fan battery to use BreezeBoost.

This fan is water-resistant and will not be damaged by light rain. However, it is not suitable to withstand heavy rain or water submersion. Do not charge or use your fan

in the rain.

Ensure that the fan blade cap is fully installed before operating the fan. Please see the Maintenance section for more details.

This error state indicates an issue with the voltage of the charger. Please be sure to only use the provided Shark charging cable and power supply.

The fan must be in Lock mode when any maintenance is performed. Lock mode prevents the fan from accidentally powering on.

We recommend cleaning the fan every 6 months or as needed.

ACCESSORIES

How often should I clean the misting accessory?

Why is the misting accessory not working eectively or not producing mist?

Clean the misting accessory every 12 months or as needed. Please note: the hardness of your water source will impact the frequency at which the misting accessory will need to be maintained.

To work properly, the misting accessory must be maintained regularly. See Maintenance section for more information.

Page 7

TROUBLESHOOTING AND FREQUENTLY ASKED QUESTIONS

We recommend cleaning the fan every 6 months or as needed.

If grill screw, bolt, or Allen wrench have been lost, see the Hardware Specs section for information on how to replace any hardware.

• LOCK MODE must be activated prior to performing maintenance. This will temporarily block all fan functions until deactivated. Lock mode prevents the fan from accidentally powering on.

1 2 3 4

Hold for 3 seconds

HARDWARE SPECS

Grill Screw

For securing the grill to the fan

Drive Type Phillips

Thread Size / Pitch M3 x 0.5mm

Length 16mm

Screwdriver

For driving the screw

Drive Type Phillips

Lights will blink three

times when Lock mode

has been activated

1. Turn on Lock mode before performing maintenance for safety. To activate, hold down the OSCILLATION icon on the fan head for 3 seconds.

5. Gently pull to remove

the FAN BLADES. With a slightly damp cloth, wipe down the interior parts of the fan.

2. Place the fan upright on a ﬂat, level surface in tabletop mode. Use the Phillips-head end of your Allen wrench to loosen the screw at the bottom of the FAN GRILL. Set screw aside.

6. Carefully replace

the BLADES onto the center shaft.

3. Rotate the FAN GRILL counterclockwise to remove it from the fan head. Set grill aside

7. Reinstall the fan blade

cap. Hold the fan blades in place while rotating the fan blade cap counterclockwise to reinstall it to the shaft.

4. Remove the fan blade cap. Hold the fan blades in place while rotating the fan blade cap clockwise to remove it from the shaft.

Size No. 1

Bolt

For securing base to pole

Drive Type Hex

Thread Size / Pitch M6 x 1mm

Length 85mm

Allen Wrench

For driving the bolt

Drive Type Hex

Size 5mm

8. Rotate the FAN GRILL

clockwise to secure it to the fan head.

9. Place the fan upright on

a ﬂat, level surface. Use the Phillips-head end of your Allen wrench to replace and tighten the screw at the bottom of the FAN GRILL.

Hold for 3 seconds

Lights will blink three

times when Lock mode

has been deactivated

10. Turn o Lock mode by pressing the Oscillation icon for 3 seconds.

Page 8

AVAILABLE ACCESSORIES

MISTING ACCESSORY

OFF

ASSEMBLY:

1. Carefully align the misting accessory with the circle in the center of the fan grill, and push it in to install. Do not use excessive force.

2. Screw the end of the misting accessory into the nozzle of a standard garden hose,

3. Turn on the hose to generate mist.

4. To adjust the amount of mist, increase or decrease the fan speed, or adjust the water pressure from the hose. Higher water

pressure or fan speed will produce more mist.

5. The valve is open when the misting accessory is taken out of the packaging. Rotate the valve clockwise to stop the flow of water of water, as shown in the diagram.

Remote Control

Use the remote control to operate your fan from a distance.

Misting Accessory

Connect the misting accessory to the front grill to produce a ﬁne mist. For assembly instructions and more information, see the Misting Accessory section.

If your misting accessory becomes less effective or stops working, follow the steps listed in below. Do NOT twist nozzles unless they are being removed for cleaning

INSTRUCTIONS FOR MAINTENANCE:

FOR BEST RESULTS, CLEAN THE MISTING ACCESSORY ONCE A YEAR , OR AS NEEDED. USING HARDER WATER WILL REQUIRE

MORE FREQUENT CLEANING.

1. Turn off the water supply and unscrew the misting accessory from the water source. Remove the other end from the fan grill

2. Unscrew the misting accessory from the water source, then pull the other end of the fan grill.

3. Place the accessory on a flat surface and carefully remove each brass nozzle, one at a time. CAUTION: Residual pressure may remain in the misting accessory.

4. To remove a nozzle, twist it counterclockwise. Do not use a wrench or any other tool. WARNING: CHOKING

HAZARD. Keep nozzles out of the reach of children.

5. To flush the misting system, once the nozzles are all

removed, connect the accessory to a garden hose or other outdoor water source. Aim the accessory away from yourself or anyone else, then turn on the water and run it through the system for 30 seconds to flush out any debris.

6. Soak the nozzles in a solution of undiluted distilled white vinegar (5% acetic acid by volume) to loosen debris that may be clogging or restricting the nozzle.

DO NOT soak the nozzles for more than 2 hours.

7. After soaking the nozzles in the solution, rinse them

thoroughly with water.

8. Carefully reinstall each nozzle by twisting clockwise until you feel resistance.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

1. The misting accessory is suitable for OUTDOOR US E O NLY.

2. The misting accessory will continue to operate when the

fan is powered off. Turn off the water source to turn off the accessory.

3. DO NOT operate the misting accessory using water pressure above typical household pressure, 60 psi.

4. DO NOT use warm or hot water. Only use cold or room temperature water.

5. DO NOT handle live electrical products while in range of the misting stream.

6. Keep non-waterproof electronic equipment and appliances out of the misting stream.

7. Children should be supervised to ensure that they DO NOT play with the misting accessory.

8. WARNING: CHOKING HAZARD. Always keep nozzles

and any other small parts out of the reach of children.

9. Cleaning and user maintenance of the misting accessory shall not be done by children without supervision.

READ AND SAVE THESE INSTRUCTIONS

Car Charger

Charge your fan on the go with the car charger accessory. For more information, see the Car Charger section.

Fan Cover

Protect your fan from damage and dust. For more information, see the Fan Cover section.

Page 9

CAR CHARGER

@sharkhome

INSTRUCTIONS FOR USE:

1. Firmly insert the car charger plug into a 12-volt outlet in your vehicle.

2. Insert the charger connector into the charging port on the underside of the fan head, between the 4 support legs.

3. If the fan is charging in a moving vehicle, be sure to position the fan in a secure location.

FAN COVER

INSTRUCTIONS FOR USE:

1. Position the cover over fan head, then slide it on until the fan is completely covered.

2. Cinch the drawstring on the bottom of the cover to secure it

in place.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

1. SAVE THESE INSTRUCTIONS. This manual contains important safety

and operating instructions for battery charger model FA20XCAR

and operating instructions for battery charger model FA20XCAR from Dongguan City Gangqi Electronics Co., Ltd.

from Dongguan City Gangqi Electronics Co., Ltd.

2. Before using this battery charger, read all instructions and cautionary

markings on the batter y charger, battery, and product using battery.

3. CAUTION: To reduce risk of injury, charge only the provided

rechargeable battery.

rechargeable battery. Other types of batteries may burst, causing injury to persons and damage.

Other types of batteries may burst, causing injury to persons and damage.

4. Do not expose charger to rain, moisture, or snow.

5. Use of an attachment not recommended or sold by the battery

charger manufacturer may result in a risk of fire, electric shock, or

charger manufacturer may result in a risk of fire, electric shock, or injury to persons.

injury to persons.

6. To reduce risk of damage to cigarette lighter connector and cord,

pull by cigarette lighter connector rather than cord when

pull by cigarette lighter connector rather than cord when disconnecting charger.

disconnecting charger.

7. To reduce risk of electric shock, unplug charger before attempting any

maintenance or cleaning. Turning off controls will not reduce this risk.

8. Do not operate charger with damaged cord or cigarette lighter

connector. Replace it immediately.

9. The car charger may be wiped clean with water once removed from

the power socket. Allow car charger to fully dry prior to use.

10. The car charger contains a 5-amp replaceable fuse. Only replace the

fuse with a 5-amp fuse, no higher. To do so, unscrew the chrome knob

fuse with a 5-amp fuse, no higher. To do so, unscrew the chrome knob at the top end of the car charging por t to access the fuse.

at the top end of the car charging por t to access the fuse.

READ AND SAVE THESE INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

1. The fan cover is not a toy. Children should not play with it as it may become unsanitary during outdoor use.

TWO (2) YEAR LIMITED WARRANTY

The Two (2) Year Limited Warranty applies to purchases made from authorized retailers of SharkNinja Operating LLC. Warranty coverage applies to the original owner and to the original product only and is not transferable.

SharkNinja warrants that the unit shall be free from defects in material and workmanship for a period of two (2) years from the date of purchase when it is used under normal household conditions and maintained according to the requirements outlined in the Owner’s Guide, subject to the following conditions and exclusions:

What is covered by this warranty?

1. The original unit and/or non-wearable parts deemed defective, in SharkNinja’s sole discretion , will be repaired or replaced up to two (2) years from the original purchase date.

2. In the event a replacement unit is issued, the warranty coverage ends six (6) months following the receipt date of the replacement unit or the remainder of the existing warranty, whichever is later. SharkNinja reserves the right to replace the unit with one of equal or greater value.

What is not covered by this warranty?

1. Normal wear and tear of wearable parts (such as batteries, etc.), which require regular maintenance and/or replacement to ensure the proper functioning of your unit, are not covered by this warranty. Replacement parts are available for purchase at sharkaccessories.com.

2. Any unit that has been tampered with or used for commercial purposes.

3. Damage caused by misuse, abuse, negligent handling, failure to per form required maintenance (e.g., not replacing the ﬁlters), or damage due to mishandling in transit.

4. Consequential and incidental damages.

IMPORTANT INFORMATION

registeryourshark.com

Scan QR code using

mobile device

RECORD THIS INFORMATION

Model Number:

Serial Number:

Date of Purchase: (Keep receipt)

Store of Purchase:

TECHNICAL SPECIFICATIONS

Voltage: 120V 60Hz / 3A Watts: 36W 4000 mAh

Beneﬁts of registering your product and creating an account:

• Get easier, faster product support and access to

warranty information

• Access troubleshooting and product care instructions

• Be among the ﬁrst to know about exclusive product promotions

TIP: You can ﬁnd the model and serial numbers on the QR code label on the underside of the fan head.

��

5. Defects caused by repair persons not authorized by SharkNinja . These defects include damages caused in the process of shipping, altering, or repairing the SharkNinja product (or any of its par ts) when the repair is performed by a repair person not authorized by SharkNinja.

6. Products purchased, used, or operated outside North America.

How to get service

If your appliance fails to operate properly while in use under normal household conditions within the warranty period, visit sharkclean.com/ support for product care and maintenance self-help. Our Customer Service Specialists are also available at 1- 855-523-4061 to assist with product support and warranty service options, including the possibility of upgrading to our VIP warranty service options for select product categories. So we may better assist you, please register your produc t online at registeryourshark. com and have the product on hand when you call.

SharkNinja will cover the cost for the customer to send in the unit to us for repair or replacement. A fee of $25.95 (subject to change) will be charged when SharkNinja ships the repaired or replacement unit.

How to initiate a warranty claim

You must call 1-855-523-4061 to initiate a warranty claim. You will need the receipt as proof of purchase. We also ask that you register your product online at registeryourshark.com and have the product on hand when you call, so we may better assist you. A Customer Service Specialist will provide you with return and packing instruction information.

How state law applies

This warranty gives you speciﬁc legal rights, and you also may have other rights that vary from state to state. Some states do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you.

BATTERY RE MOVAL AND DISPOSAL

This product contains an integral lithium battery (non-replaceable), and the remote control uses a lithium coin battery (replaceable). DO NOT incinerate or compost the product with its integral battery or the remote battery. When the fan battery can no longer hold a charge, dispose of it or recycle it (with integral battery) in accordance with local ordinances or regulations. Remove, replace, and dispose of or recycle the spent remote battery likewise. In some areas, it is illegal to place spent lithium batteries in the trash or in a municipal solid waste stream. Return spent battery to an authorized recycling center or to retailer for recycling. Contact your local recycling center for information on where to drop o the spent battery.

FCC WARNINGS

Note: This unit has been tested and found to comply with FCC limits for Class B digital devices. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This unit generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

To see if this unit interferes with radio or television reception, try turning it o and on.

To correct any interference:

■ Reorient or relocate the receiving antenna.

■ Increase the distance between the unit and the receiver.

■ Connect the unit to a dierent outlet than the receiver.

■ Consult the dealer or an experienced technician for help.

Caution: Any changes or modiﬁcations to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate it.

PLEASE READ CAREFULLY AND KEEP FOR FUTURE REFERENCE.

This Owner’s Guide is designed to help you get a complete understanding of your new Shark® fan. SharkNinja Operating LLC

US: Needham, MA 02494 CAN: Ville St-Laurent, QC H4S 1A7

1-800-798-7398 sharkclean.com

Illustrations may dier from actual product. We are constantly striving to improve our products; therefore the speciﬁcations contained herein are subject to change without notice.

This product may be covered by one or more U.S. patents. See sharkninja.com/patents for more information.

FA222�IB�A4-Online�REV�Mv1

Shark FA200 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual