Congratulations! You are the owner of the Shark 1600 Watt Professional Steam
Iron. To fully enjoy the advantages of your appliance, please take a few minutes to
read all the “Use & Care Instructions” and keep the instructions handy for easy
reference. Please review the product warranty and mail the owner registration
form.
Model EP480
Steam Iron
EURO-PRO Operating LLC, 21 Lawrence Paquette Industrial Drive, Champlain, New York 12919 (800) 798-7398
IMPORTANT SAFEGUARDS
When using your iron, basic safety precautions should always be followed, including the following:
1. Read all instructions before using the iron.
2. Use iron only for its intended use.
3. To protect against a risk of electrical shock, do not immerse in water or other liquids.
4. The iron thermostat should always be turned to its lowest position before plugging or unplugging from outlet.
Never yank cord to disconnect from outlet, instead grasp plug and pull to disconnect.
5. Do not allow cord to touch hot surfaces. Let iron cool completely before putting away. Loop cord loosely
around iron when storing.
6. Always disconnect iron from electrical outlet when filling iron with water or emptying and when not in use.
7. Do not operate iron with a damaged cord or if the iron has been dropped or damaged. To avoid the risk of
electrical shock, do not disassemble the iron. Send it to an authorized EURO-PRO Operating LLC service
center for examination and repair. Incorrect reassembly can cause a risk of electric shock when iron is used.
8. Close supervision is necessary for any appliance used by or near children. Do not leave iron unattended while
connected or on an ironing board.
9. Burns can occur from touching hot metal parts, hot water or steam. Use caution when you turn a steam iron
upside down as there may be hot water in the reservoir. Never direct steam at any person, especially when
using the iron in a vertical position. The steam is very hot and can cause burns.
10. The use of accessory attachments not recommended by EURO-PRO Operating LLC may result in fire,
electrical shock or personal injury.
11. Do not operate in the presence of explosive and/or flammable fumes.
12. Do not use iron outdoors.
13. This product is for household use only.
Rev. 02/03A
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
2
SPECIAL INSTRUCTIONS
1. To avoid a circuit overload, do not operate another high-wattage appliance on the same circuit.
2. If an extension is absolutely necessary, a 15-ampere rated cord with a polarized plug should be used.
Cords rated for less amperage may overheat. Care should be taken to arrange the cord so that it
cannot be pulled on or tripped over.
POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other).
As a safety feature, this plug will fit into a polarized outlet only one way. If
the plug does not fit fully into the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do no attempt to defeat this safety
feature.
SAVE THESE INSTRUCTIONS
3
SHARK PROFESSIONAL STEAM IRON
1. Power Supply Cord 8. Spray Nozzle
2. Auto Shut-Off Light 9. Temperature Control Dial
5. Burst of Steam Button12. Water Measuring Beaker
6. Spray Button13. Iron Heel Rest
7. Water Filling Inlet Cover
4
IMPORTANT
Resetting After Auto Shut-Off
The auto shut-off safety function of your SHARK EP480 Iron is designed to engage after
approximately 8 minutes of non use. The blue indicator light will flash when the auto shut-off has
activated.
To reset your iron and continue ironing follow these steps.
1)Lift iron from stand.
2) Holding the iron horizontally in front of you, gently rock the iron back and forth several times. This
motion will reset the safety switch inside the iron. Do not shake the iron.
The red temperature light will illuminate when the auto shut-off system has been reset. Allow time for
the iron to re-heat. The red indicator light will go out when the iron is ready for use.
Caution:
Do not use the auto shut-off feature as a substitute for turning
the iron off and unplugging the iron when not in use.
5
BEFORE FIRST USE
Remove any labels, stickers or tags which may be attached to the body or soleplate of the iron
before using the iron.
Read all instructions for use carefully. Always follow the Important Safeguards.
IMPORTANT
The first time an iron is used, some odor and small white particles may come out of the steam vents.
This is perfectly normal and will cease to occur after the iron has been in use for a short while.
Before you start using your iron, follow the instructions in the manual and do the following in
order to eliminate any odor and small white residue particles and to ensure optimum steam
performance.
Fill the iron with regular tap water.
Set the temperature control dial at its highest and steam control at ‘0’.
When the thermostat light goes off to indicate that the iron has reached the selected
temperature, set the steam control at MAX.
Keep the iron in a horizontal position and allow it to steam until the water runs out.
Press the steam burst button to eliminate white residue particles.
Repeat this procedure through 2 or 3 fillings of water.
6
CHOOSING THE IRONING TEMPERATURE
Set the temperature dial according to the type of fabric .
• Synthetics
(low temperature)
• • Silk, Wool
(medium temperature)
• • • Cotton, Linen
(high temperature)
Temperature Control DialVariable Steam Control
Please note: Before starting to iron delicate fabrics, it is best to first test the temperature of the iron
on a hem or an inside seam.
CONNECTING THE IRON TO THE POWER SUPPLY
• Make sure that the variable steam control dial is set at ‘0’.
• Place the iron upright on the heel rest.
• Select the required temperature setting on the temperature control dial.
• The red thermostat light will come on indicating that the iron is heating up.
• When the red light goes out, the set temperature has been reached and the iron is ready to use.
• The thermostat ready light will go on & off as the thermostat is switching the heating element
on & off to maintain the selected temperature.
7
FILLING WITH WATER
• Ensure the unit is unplugged from the main supply before filling.
• Set the variable steam control (4) to position "MIN" (ie. No steam)
• slide the water filling inlet cover (7) down and use the measuring
beaker (12) to pour the water in through the filling aperture (see
picture).
• Do not overfill.
Note: Regular tap water can be used up to 12 grains water hardness but if your water exceeds
this we suggest using 1/3 tap water and 2/3 distilled water. Never use 100% distilled water as
this could cause water spitting and low steam performance.
8
IRONING WITH STEAM
• Make sure iron is unplugged from power source.
• Set the variable steam control to ‘0’.
• Fill the iron with water following the instructions for filling.
• Plug the cord into a 120 Volt AC electrical outlet.
• Set the temperature control dial within the steam area i.e. ‘•••’.
• Make sure that the iron has reached the selected temperature with the variable steam control set at ‘0’.
IMPORTANT:Do not open the steam control until the thermostat light goes off to indicate that the
selected temperature within the steam range has been reached. If you move the
variable steam control up from ‘0’ before the correct temperature is reached, the iron
will drip water.
• The variable steam control offers a few different settings:
PLEASE NOTE: For maximum steam the temperature control dial should be set at ••• .
The temperature control should be set at the beginning only for very
delicate fabrics requiring very gentle steam (setting •).
• Steam is produced as soon as the iron is held in a horizontal position.
• Steam will stop coming out when the iron is put on its heel in a vertical position
or by turning the steam control dial to ‘0’.
• Vertical steam: For vertical burst of steam, pump control button (5) located on
the top of the handle selection of your iron. The vertical steam function is
useful for steaming curtains and drapes will still hanging, or for powering
out stubborn wrinkles while ironing on a board.
9
WATER SPRAY
• Use the spray button to add moisture to stubborn wrinkles.
• First make sure that there is water in the tank.
• Press the spray button (6) slowly to get a jet spray.
• Press the spray button strongly and quickly to get a mist.
• Please note: If spray does not come out when you press the spray button, cover the spray opening
with your finger and press a few times.
TO EMPTY THE IRON
• Always empty iron after each usage.
• After using the iron, turn the variable steam control to ‘0’ and the temperature
control dial to ‘minimum’.
• Unplug the iron from the power source.
• Set variable steam control to ‘MAX’.
• Open the water inlet cover and turn the iron up-side down over the sink
with the tip pointing downward and allow the water to flow from the
opening.
• Set variable steam control to ‘0’.
• Allow iron to cool on the iron rest before storing.
WARNING: Use caution when you turn the iron up-side down - there
may be hot water in the reservoir. Burns can occur from
touching hot metal parts, hot water or steam.
10
TO ADD WATER
• Unplug iron from the electrical outlet.
• Follow instructions to empty the iron.
• Then, follow the instructions for filling the iron.
Following this procedure will ensure that you do not overfill the iron.
SELF-CLEANING
In order to remove calcium and built-up particles, the self-cleaning system should be run at least once
a month.
• Fill the watering beaker provided to the half-full mark and then pour into the water reservoir.
• Set the variable steam control (4) to the no steam position.
• Insert the main plug into the wall socket.
• Set the temperature control dial (9) to the maximum temperature.
• Wait until the thermostat light (3) goes off and steam iron has reached preset temperature.
• Remove the plug from the wall socket.
• Hold the steam iron horizontally over a sink.
• Turn the variable steam control (4) to “Self-Clean ” position. Hot water and steam will be
emitted from the soleplate. Swing the steam iron lightly back and forth gently to allow lime and dust
particles to come out.
• When the water reservoir is empty, shift the variable steam control from “Self-Clean” position to “0”.
• Stand the iron upright and insert the plug into the wall socket to let the iron heat up again.
• Move the iron over a clean cotton cloth to clean the soleplate and let the remaining water on
the soleplate evaporate.
11
CLEANING, STORAGE & MAINTENANCE
• Always turn the variable steam control to ‘0’ after you have emptied the water tank.
• Allow iron to cool down.
• Always store the iron on the metal iron rest or in an upright position on it’s heel rest to
protect the soleplate.
• From time to time clean the exterior with a damp cloth and wipe dry.
• If you use spray starch, wipe the soleplate occasionally with a soft damp cloth to prevent the
forming of a deposit.
• If the iron has not been used for a few weeks, hold the iron horizontally and allow it to steam for
2 minutes before ironing.
WARNING:
The anti-drip function reduces water dripping and water stains. It does
not prevent water dripping or water stains if you press the steam burst
button too often or if temperature is too low. The amount of water
droplets will eventually decrease after iron is used for 2 to 3 tankfuls of
steaming and ironing.
12
Iron Troubleshooting
ProblemPotential Reasons & Solutions
• Iron should be plugged into a 120V AC electrical outlet only.
Iron does not heat
Make sure that the plug is securely in the socket.
• Thermostat set too low. Turn to higher setting.
• Auto shut-off may be activated. Move iron gently or shake.
Thermostat Ready light
goes On and Off
Some odor or small particles
come out of steam vents of
new iron
Iron does not steam
Continued...
• This is normal. The light goes On and Off as the thermostat is switching
the heating element On and Off to maintain the selected temperature.
• This is normal. Follow instructions for first use and allow iron to steam
through 2-3 fillings & press the steam burst button occasionally to
eliminate small white particles.
• Water tank may be empty or water level is very low. Add water.
• Make sure that the temperature control dial and the variable steam
control are correctly set. For maximum steam, (setting ‘Max’ on steam
control), temperature control dial should be set on ‘•••’.
• Always allow the iron to reach the selected temperature with the steam
setting at ‘0’. Make sure the temperature control dial is set in the correct
steam area and the steam control is not
temperature dial to higher setting. e.g. ‘•••’ and the steam control to ‘Max’.
• If temperature setting and steam control setting are correct and there is no
steam, gently
variable steam control from ‘0’ to ‘Max’ a few times.
tap the soleplate on the ironing board a few times. Move the
on ‘0’. For more steam, turn
13
Iron Troubleshooting
(continued)
ProblemPotential Reasons & Solutions
Water droplets coming
from steam vents
• Iron may not be hot enough. Set thermostat to the ‘max’ position.
Always allow iron sufficient time to heat up (thermostat light goes
off) before activating the variable steam control.
• Auto-Off may be activated. Move iron or gently shake.
• Overuse of steam burst. Allow more time between each burst.
• Iron may have been overfilled. Turn iron off,empty water and follow
instructions for filling.
• Steam performance may be low if iron requires seasoning. Use
regular tap water for 1or 2 tanks until steam performance improves.
14
IMPORTANT SERVICE INFORMATION
In the event that your iron fails to operate properly or if your iron needs servicing
DO NOT RETURN IT TO THE STORE
First check the troubleshooting guide on the back of this page and make sure that you have
followed all the instructions in the operating manual. If your iron still does not operate properly,
send your iron, postage prepaid, together with a copy of your sales receipt to:
Warranty Dept.
EURO-PRO Operating LLC
21 Lawrence Paquette Industrial Drive
Champlain, N. Y. 12919
Tel: (800) 798-7398
If the warranty period has expired, please send your iron postage pre-paid to the Service Department of
EURO-PRO Operating LLC at the above address. You will be advised of the cost of repair before any servicing
is done unless you enclose a note indicating that you would like us to proceed with the repairs
and return the iron to you C.O.D.
DO NOT FORGET TO ENCLOSE YOUR NAME, ADDRESS, TELEPHONE NUMBER AND COPY
OF SALES RECEIPT.
ONE YEAR LIMITED WARRANTY
EURO-PRO Operating LLC
purchase. The liability of
This warranty does not cover damage caused by misuse, negligence, use on improper current or voltage, use contrary to operating instructions or
disassembly, repair or alteration by any person other than an authorized
Product repair or replacement, at our option, is your sole remedy. This warranty excludes all other legal and/or conventional warranties. The responsibility
EURO-PRO Operating LLC
of
EURO-PRO Operating LLC
of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights which vary from state to state.
If you have a claim under this warranty or if you require service
Send the product , postage prepaid to our factory service center:Warranty Department
Please include a copy of your sales receipt, $9.50 to cover the cost of return shipping & handling and a letter explaining the nature of your difficulty.
Do not forget to enclose your name, address and telephone number.
If the warranty period has expired, please send your iron postage pre-paid to: Service Department
You will be advised of the cost of repair before any servicing is done unless you enclose a note indicating that you would like us to proceed with
the repairs and return the iron to you C.O.D.
warrants this product to be free from defects in material and workmanship for a period of one (1) year from the date of
EURO-PRO Operating LLC
, if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is
liable for incidental or consequential damages of any nature whatsoever. Some States do not permit the exclusion or limitation
is limited solely to the repair or replacement of the product at
EURO-PRO Operating LLC
DO NOT RETURN THIS PRODUCT TO THE STORE!
EURO-PRO Operating LLC
21 Lawrence Paquette Industrial Drive
Champlain, N. Y. 12919
Tel: (800) 798-7398
Please complete and return within ten (10) days of purchase. The registration will enable us to contact you in the event a product defect is discovered. By
returning this card you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.