SGS Thomson Microelectronics TSL062ID, TS062ACD, TL062M, TL062IN, TL062I Datasheet
...
1 - Output 1
2 - Inverting input 1
3 - Non-inverting input1
4-V
CC
-
5 - Non-inverting input 2
6 - Inverting input 2
7 - Output 2
8-V
CC
+
TL062
TL062A - TL062B
LOW POWER J-FET DUALOPERATIONAL AMPLIFIERS
October 1997
1
2
3
45
6
7
8
-
+
-
+
PIN CONNECTIONS (top view)
■
VERYLOW POWERCONSUMPTION : 200µA
■
WIDE COMMON-MODE (UP TO V
CC
+
) AND
DIFFERENTIALVOLTAGERANGES
■
LOW INPUTBIAS AND OFFSETCURRENTS
■
OUTPUTSHORT-CIRCUIT PROTECTION
■
HIGH INPUT IMPEDANCE J-FET INPUT
STAGE
■
INTERNAL FREQUENCYCOMPENSATION
■
LATCHUP FREE OPERATION
■
HIGH SLEWRATE: 3.5V/µs
DESCRIPTION
The TL062, TL062A and TL062B are high speed
J-FETinput dualoperationalamplifier family. Each
of these J-FET input operational amplifiers incorporates well matched, high voltage J-FET and bipolar transistors in a monolithicintegratedcircuit.
The devicesfeature highslew rates, lowinput bias
and offsetcurrents,andlowoffsetvoltagetemperature coefficient.
ORDER CODES
Part Number Temperature Range
Package
ND
TL062M/AM/BM -55
o
C, +125oC ●●
TL062I/AI/BI -40oC, +105oC ●●
TL062C/AC/BC 0oC, +70oC ●●
Example : TL062IN
N
DIP8
(Plastic Package)
D
SO8
(Plastic Micropackage)
1/10
Notes : 1. All voltage values, except differential voltage, are withrespect to the zero reference level (ground) of the supply voltages where
the zero reference level is the midpointbetween V
CC
+
and V
CC
-
.
2. Differentialvoltagesare at the non-inverting input terminal with respect to the inverting input terminal.
3. The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is less.
4. The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to ensure that the
dissipation rating is not exceeded.
MAXIMUMRATINGS
Symbol Parameter TL062M,AM,BM TL062I,AI,BI TL062C,AC,BC Unit
V
CC
Supply Voltage - (note1) ±18 ±18 ±18 V
V
i
Input Voltage - (note3) ±15 ±15 ±15 V
V
id
Differential Input Voltage- (note 2) ±30 ±30 ±30 V
P
tot
Power Dissipation 680 680 680 mW
Output Short-Circuit Duration (Note 4) Infinite Infinite Infinite
T
oper
Operating Free-Air Temperature
Range
-55 to +125 -40 to +105 0 to +70
o
C
T
stg
Storage Temperature Range - 65 to + 150 -65 to + 150 - 65 to + 150
o
C
Non-inverting
Input
Inverting
Input
Output
1/2 TL062
4.2k
Ω
100 Ω
45k Ω
220
Ω
64Ω
270Ω
3.2k
Ω
V
CC
V
CC
SCHEMATIC DIAGRAM
TL062 - TL062A - TL062B
2/10
ELECTRICAL CHARACTERISTICS
V
CC
=± 15V, T
amb
=25oC (unless otherwisespecified)
Symbol Parameter
TL062M TL062I TL062C
Unit
Min. Typ. Max. Min. Typ. Max. Min. Typ. Max.
V
io
Input Offset Voltage (Rs=50Ω)
T
amb
=25oC
T
min
. ≤ T
amb
≤ T
max.
36
15
36
9
315
20
mV
DV
io
Temperature Coefficient of Input
Offset Voltage (R
s
=50Ω)101010
µV/
o
C
I
io
Input Offset Current *
T
amb
=25oC
T
min
. ≤ T
amb
≤ T
max.
5 100
20
5 100
10
5 2005pA
nA
I
ib
Input Bias Current *
T
amb
=25oC
T
min.
≤ T
amb
≤ T
max
.
30 200
50
30 200
20
30 40010pA
nA
V
icm
Input Common Mode Voltage
Range
±11.5 +15
-12
±11.5 +15
-12
±11 +15
-12
V
V
OPP
Output Voltage Swing (RL= 10kΩ)
T
amb
=25oC
T
min
. ≤ T
amb
≤ T
max
.
202027 202027 202027
V
A
vd
Large Signal Voltage Gain
(R
L
= 10kΩ,Vo=±10V)
T
amb
=25oC
T
min
. ≤ T
amb
≤ T
max
.
4
4
64
4
63
3
6
V/mV
GBP Gain Bandwidth Product
(T
amb
=25oC, RL= 10kΩ
C
L
= 100pF) 1 1 1
MHz
R
i
Input Resistance 10
12
10
12
10
12
Ω
CMR Common Mode Rejection Ratio
(R
s
= 50Ω) 8086 8086 7076
dB
SVR Supply Voltage Rejection Ratio
(R
s
=50Ω) 8095 8095 7095
dB
I
cc
Supply Current (Per Amplifier)
(T
amb
=25oC, no load, no signal) 200 250 200 250 200 250
µA
V
O1/VO2
Channel Separation
(A
v
= 100, T
amb
=25oC) 120 120 120
dB
P
D
Total Power Consumption
(Each Amplifier)
(T
amb
=25oC, no load, no signal) 6 7.5 6 7.5 6 7.5
mW
* Input bias currents of a FET-input operational amplifier are normal junction reverse currents, which are temperature sensitive.
Pulse techniques must be used that will maintain the junction temperature as closes to the ambient temperature as possible.
ELECTRICAL CHARACTERISTICS (continued)
V
CC
=± 15V, T
amb
=25oC
Symbol Parameter
TL062C,I,M
Unit
Min. Typ. Max.
SR Slew Rate (V
i
= 10V, RL= 10kΩ,CL= 100pF, AV= 1) 1.5 3.5 V/µs
t
r
Rise Time (Vi= 20mV, RL= 10kΩ,CL= 100pF, AV= 1) 0.2 µs
K
OV
Overshoot Factor (Vi= 20mV, RL= 10kΩ,CL= 100pF, AV=1)
(see figure 1) 10
%
e
n
Equivalent Input Noise Voltage
(R
s
= 100Ω, f = 1KHz) 42
nV
√Hz
TL062 - TL062A - TL062B
3/10
Loading...